Titanium Dioxide Nanomaterials for Photovoltaic Applications

Alkyl effects on charge recombination in copper electrolyte-based dye-sensitized solar cells: Insights for targeted molecular design towards high performance

Two quinoxaline dyes utilized in copper-electrolyte-based dye-sensitized solar cells (Cu-DSSCs) are theoretically investigated to analyze the impact of alkyl chains on dye performance. The investigation shows that ZS4, known for its record efficiency of up to 13.2 %, exhibits higher electron coupling and fewer binding sites for dye-[Cu(tmby)2]2+ interaction compared to ZS5. Contrary to common belief, alkyl chains are found to not only provide shielding but also hinder the interaction between dye and [Cu(tmby)2]2+ by influencing the optimal conformation of dyes, thereby impeding the charge recombination process. It is crucial to consider the influence of alkyl chains on dye conformation when discussing the relationship between dye structure and performance, rather than oversimplifying it as often done traditionally. Building on these findings, eight dyes are strategically designed by adjusting the position of the alkyl chain to further decrease charge recombination compared to ZS4. Theoretical evaluation of these dyes reveals that changing the alkyl chain on the nitrogen atom from 2-ethylhexyl (ZS4) to 1-hexylheptyl (D3-2) not only reduces the charge recombination rate but also enhances light harvesting ability. Therefore, D3-2 shows potential as a candidate for experimental synthesis of high-performance Cu-DSSCs with improved efficiency.

Illuminating Pathways to Dynamic Nanotribology: Light-Mediated Active Control of Interfacial Friction with Nanosuspensions

Active control of nanotribological properties is a challenge. Materials responsive to external stimuli may catalyze this paradigm shift. Recently, the nanofriction of a thin film is modulated by light, ushering in phototribology. This frontier is expanded here, by investigating photoactive nanoparticles in lubricants to confer similar functionality to passive surfaces. Quartz-crystal microbalance (QCM) is employed to assess the phototribological behavior of aqueous suspensions of titanium dioxide nanoparticles. A comparison of dark and illuminated conditions provides the first demonstration of tuning the interfacial friction in solid-nanosuspension interfaces by light. Cyclic tests reveal reversible transitions between higher (dark) and lower friction (illuminated) regimes. These transitions are underpinned by transient states with surface charge variations, as confirmed by Zeta potential measurements. The accumulated surface charge increases repulsion within the system and favors sliding. Upon cessation of illumination, the system returns to its prior equilibrium state. These findings impact not only nanotribology but nanofluidics and nanorheology. Furthermore, the results underscore the need to consider light-induced effects in other scenarios, including the calculation of activity coefficients of photoactive suspensions. This multifaceted study introduces a new dimension to in operando frictional tuning, beckoning a myriad of applications and fundamental insights at the nanoscale.

Facile Synthesis of Organic-Inorganic Hybrid Heterojunctions of Glycolated Conjugated Polymer-TiO2-X for Efficient Photocatalytic Hydrogen Evolution

The utilization of the organic-inorganic hybrid photocatalysts for water splitting has gained significant attention due to their ability to combine the advantages of both materials and generate synergistic effects. However, they are still far from practical application due to the limited understanding of the interactions between these two components and the complexity of their preparation process. Herein, a facial approach by combining a glycolated conjugated polymer with a TiO2-X mesoporous sphere to prepare high-efficiency hybrid photocatalysts is presented. The functionalization of conjugated polymers with hydrophilic oligo (ethylene glycol) side chains can not only facilitate the dispersion of conjugated polymers in water but also promote the interaction with TiO2-X forming stable heterojunction nanoparticles. An apparent quantum yield of 53.3% at 365 nm and a hydrogen evolution rate of 35.7 mmol h-1 g-1 is achieved by the photocatalyst in the presence of Pt co-catalyst. Advanced photophysical studies based on femtosecond transient absorption spectroscopy and in situ, XPS analyses reveal the charge transfer mechanism at type II heterojunction interfaces. This work shows the promising prospect of glycolated polymers in the construction of hybrid heterojunctions for photocatalytic hydrogen production and offers a deep understanding of high photocatalytic performance by such heterojunction photocatalysts.

Low density phases of TiO2 by cluster self-assembly

The interest in titanium dioxide (TiO2 ) phases is growing due to the number of applications in cosmetics, food industry and photocatalysis, an increase that is driven by its exceptional properties when engineered at the nanoscale like in the form of nanoparticles. Our goal is to discover unknown low-density phases of TiO2 , with potential for applications in various fields. We then use well-known TiO2 clusters as fundamental building blocks to be self-assembled into unique structures to study their distinct characteristics. Density functional calculations are employed to relax the structures and identify the most stable TiO2 structures within an energy range of 0.1 eV per atom from the rutile and anatase phases, which are confirmed, validating our methodology. Going beyond conventional phases, we found two-dimensional TiO2 structures, previously explored in separate studies, and showing typical structures of transition metal dichalcogenide layers, that forge a bridge between different TiO2 structures. It is noteworthy that our investigation uncovered an entirely novel class of TiO2 structures featuring hexagonal cages like beehive channels, opening novel phases with huge potential. These discovered low-density phases are interesting, particularly the hexagonal cage structures with remarkable large gaps, because they introduce other dimensions for uncharted applications in the ever-growing TiO2 landscape.

Synthesis, Characterization, and Properties of a Titanium(IV)-Tetrathiafulvalene-Based Complex

To deeply investigate the interaction between a tetrathiafulvalene (TTF) unit and a Ti(IV) center, a monomeric heteroleptic octahedral Ti(IV) complex containing a diimine ligand composed of a 1,10-phenanthroline core fused with a TTF fragment (ligand 2a) was prepared. The stable complex formulated as Ti(1)2(2a), where 1 is a 2,2'-biphenolato derivative, was efficiently synthesized by following a one-step approach. This complex and its model species [Ti(1)2(2b)] were fully characterized in solution, and their solid-state structures were established by single-crystal X-ray diffraction analysis. Density functional theory calculations allowed the assignment of the frontier orbitals involved in the electronic transitions characterized by ultraviolet-visible absorption spectroscopy. Electrochemical and spectroelectrochemical studies revealed that the TTF unit within Ti(1)2(2a) can undergo two reversible one-electron oxidation processes; a reversible one-electron reduction of the Ti(IV) atom was highlighted. The photophysical measurements performed for this donor-acceptor molecular system indicated that an electron transfer process upon light excitation occurred within Ti(1)2(2a).

Photonic post-processing of a multi-material transparent conductive electrode architecture for optoelectronic device integration

Emerging flexible optoelectronic devices require multi-material processing capabilities to fully enable the use of temperature-sensitive substrates and materials. This report demonstrates how photonic sintering enables the processing of materials with very different properties. For example, charge carrier transport/blocking metal-oxides, and transparent conductive silver nanowire-based electrodes ought to be compatible with low-energy and high-throughput processing for integration onto flexible low-temperature substrates. Compared to traditional post-processing methods, we show a rapid fabrication route yielding highly-stable hybrid electrode architectures on polyethylene terephthalate (PET). This architecture consists of an interconnected silver nanowire network encapsulated with a thin crystalline photo-sensitive titanium dioxide (TiO2) coating, allowing both layers to be treated using independent photonic post-processing sintering steps. The first step sinters the nanowires, while the second completes the conversion of the top metal-oxide layer from amorphous to crystalline TiO2. This approach improves on the fabrication speed compared to oven processing, while delivering optical and electrical characteristics comparable to the state of the art. Optimized transparency values reach 85% with haze values down-to 7% at 550 nm, while maintaining a sheet resistance of 18.1 Ω sq.-1. However, this hybrid architecture provides a much stronger resilience to degradation, which we demonstrate through exposure to harsh plasma conditions. In summary, this study shows how carefully-optimized photonic curing post-processing can provide more-stable hybrid architectures while using a multi-material processing technique suitable for high-volume manufacturing on low-temperature substrates.

Ecofriendly alkali metal cations diffusion improves fabrication of mixed-phase titania polymorphs on fixed substrate by chemical vapor deposition (CVD) for photocatalytic degradation of azo dye

Controlling the nanoscale synthesis of semiconductor TiO2 on a fixed substrate has fascinated the curiosity of academics for decades. Synthesis development is required to give an easy-to-control technique and parameters for TiO2 manufacture, leading to advancements in prospective applications such as photocatalysts. This study, mixed-phase TiO2(B)/other titania thin films were synthesized on a fused quartz substrate utilizing a modified Chemical vapor depodition involving alkali-metal ions (Li+, Na+, and K+) solution pre-treatment. It was discovered that different cations promote dramatically varied phases and compositions of thin films. The films had a columnar structure with agglomerated irregular-shaped particles with a mean thickness of 800-2000 nm. Na+ ions can promote TiO2(B) more effectively than K+ ions, however Li+ ions cannot synthesize TiO2(B). The amounts of TiO2(B) in thin films increase with increasing alkali metal (K+ and Na+) concentration. According to experimental and DFT calculations, the hypothesized TiO2(B) production mechanism happened via the meta-stable intermediate alkaline titanate transformation caused by alkali-metal ion diffusion. The mixed phase of TiO2(B) and anatase TiO2 on the fixed substrate (1 × 1 cm2) obtained from Na+ pre-treated procedures showed significant photocatalytic activity for the degradation of methylene blue. K2Ti6O12, Li2TiO3, Rutile TiO2, and Brookite TiO2 phase formations produced by K+ and Li + pretreatment are low activity photocatalysts. Photocatalytic activities were more prevalent in NaOH pre-treated samples (59.1% dye degradation) than in LiOH and KOH pre-treated samples (49.6% and 34.2%, respectively). This revealed that our developed CVD might generate good photocatalytic thin films of mixed-phase TiO2(B)/anatase TiO2 on any substrate, accelerating progress in future applications.

Comprehensive Analysis of Titanium Oxide Nanoparticle Size and Surface Properties on Neuronal PC-12 Cells: Unraveling Cytotoxicity, Dopaminergic Gene Expression, and Acetylcholinesterase Inhibition

Titanium oxide nanoparticles can penetrate the blood-brain barrier, infiltrate the central nervous system, and induce neurotoxicity. One of the most often utilized nanoparticles has been investigated for their neurotoxicity in many studies. Nonetheless, there remains an unexplored aspect regarding the comparative analysis of particles varying in size and nanoparticles of identical dimensions, both with and devoid of surface coating. In the current study, we synthesized two differently sized nanoparticles, TiO2-10 (10 nm) and TiO2-22 (22 nm), and nanoparticles of the same size but with a polyvinylpyrrolidone surface coating (TiO2-PVP, 22 nm) and studied their toxic effects on neural PC-12 cells. The results highlighted significant dose- and time-dependent cytotoxicity at concentrations ≥10 μg/mL. The exposure of TiO2 nanoparticles significantly elevated reactive oxygen and nitrogen species levels, IL-6 and TNF-α levels, altered the mitochondrial membrane potential, and enhanced apoptosis-related caspase-3 activity, irrespective of size and surface coating. The interaction of the nanoparticles with acetylcholinesterase enzyme activity was also investigated, and the results revealed a dose-dependent suppression of enzymatic activity. However, the gene expression studies indicated no effect on the expression of all six genes associated with the dopaminergic system upon exposure to 10 μg/mL for any nanoparticle. The results demonstrated no significant difference between the outcomes of TiO2-10 and TiO2-22 NPs. However, the polyvinylpyrrolidone surface coating was able to attenuate the neurotoxic effects. These findings suggest that as the TiO2 nanoparticles get smaller (towards 0 nm), they might promote apoptosis and inflammatory reactions in neural cells via oxidative stress, irrespective of their size.

Microbial synthesis of titanium dioxide nanoparticles and their importance in wastewater treatment and antimicrobial activities: a review

Nanotechnology (NT) and nanoparticles (NPs) have left a huge impact on every field of science today, but they have shown tremendous importance in the fields of cosmetics and environmental cleanup. NPs with photocatalytic effects have shown positive responses in wastewater treatment, cosmetics, and the biomedical field. The chemically synthesized TiO2 nanoparticles (TiO2 NPs) utilize hazardous chemicals to obtain the desired-shaped TiO2. So, microbial-based synthesis of TiO2 NPs has gained popularity due to its eco-friendly nature, biocompatibility, etc. Being NPs, TiO2 NPs have a high surface area-to-volume ratio in addition to their photocatalytic degradation nature. In the present review, the authors have emphasized the microbial (algae, bacterial, fungi, and virus-mediated) synthesis of TiO2 NPs. Furthermore, authors have exhibited the importance of TiO2 NPs in the food sector, automobile, aerospace, medical, and environmental cleanup.

Colloidal semiconductor nanocrystals: from bottom-up nanoarchitectonics to energy harvesting applications

Colloidal semiconductor nanocrystals (NCs) have been extensively investigated owing to their unique properties induced by the quantum confinement effect. The advent of colloidal synthesis routes led to the design of stable colloidal NCs with uniform size, shape, and composition. Metal oxides, phosphides, and chalcogenides (ZnE, CdE, PbE, where E = S, Se, or Te) are few of the most important monocomponent semiconductor NCs, which show excellent optoelectronic properties. The ability to build quantum confined heterostructures comprising two or more semiconductor NCs offer greater customization and tunability of properties compared to their monocomponent counterparts. More recently, the halide perovskite NCs showed exceptional optoelectronic properties for energy generation and harvesting applications. Numerous applications including photovoltaic, photodetectors, light emitting devices, catalysis, photochemical devices, and solar driven fuel cells have demonstrated using these NCs in the recent past. Overall, semiconductor NCs prepared via the colloidal synthesis route offer immense potential to become an alternative to the presently available device applications. This feature article will explore the progress of NCs syntheses with outstanding potential to control the shape and spatial dimensionality required for photovoltaic, light emitting diode, and photocatalytic applications. We also attempt to address the challenges associated with achieving high efficiency devices with the NCs and possible solutions including interface engineering, packing control, encapsulation chemistry, and device architecture engineering.

Photoelectrochemical Engineering for Light-Assisted Rechargeable Metal Batteries: Mechanism, Development, and Future

Rechargeable battery devices with high energy density are highly demanded by  our  modern society. The use of metal anodes is extremely attractive for future rechargeable battery devices. However, the notorious metal dendritic and instability of solid electrolyte interface issues pose a series of challenges for metal anodes. Recently, considering the indigestible dynamical behavior of metal anodes, photoelectrochemical engineering of light-assisted metal anodes have been rapidly developed since they efficiently utilize the integration and synergy of oriented crystal engineering and photocatalysis engineering, which provided a potential way to unlock the interface electrochemical mechanism and deposition reaction kinetics of metal anodes. This review starts with the fundamentals of photoelectrochemical engineering and follows with the state-of-art advance of photoelectrochemical engineering for light-assisted rechargeable metal batteries where photoelectrode materials, working principles, types, and practical applications are explained. The last section summarizes the major challenges and some invigorating perspectives for future research on light-assisted rechargeable metal batteries.

Indoor Photovoltaic Fiber with an Efficiency of 25.53% under 1500 Lux Illumination

Photovoltaic devices represent an efficient electricity generation mode. Integrating them into textiles offers exciting opportunities for smart electronic textiles-with the ultimate goal of supplying power for wearable technology-which is poised to change how electronic devices are designed. Many human activities occur indoors, so realizing indoor photovoltaic fibers (IPVFs) that can be woven into textiles to power wearables is critical, although currently unavailable. Here, a dye-sensitized IPVF is constructed by incorporating titanium dioxide nanoparticles into aligned nanotubes to produce close contact and stable interfaces among active layers on a curved fiber substrate, thus presenting efficient charge transport and low charge recombination in the photoanode. With the combination of highly conductive core-sheath Ti/carbon nanotube fiber as a counter electrode, the IPVF shows a certified power conversion efficiency of 25.53% under 1500 lux illuminance. Its performance variation is below 5% after bending, twisting, or pressing for 1000 cycles. These IPVFs are further integrated with fiber batteries as self-charging power textiles, which are demonstrated to effectively supply electricity for wearables, solving the power supply problem in this important direction.

Nanorobot-Mediated Synchronized Neuron Activation

Interactions between active materials lead to collective behavior and even intelligence beyond the capability of individuals. Such behaviors are prevalent in nature and can be observed in animal colonies, providing these species with diverse capacities for communication and cooperation. In artificial systems, however, collective intelligence systems interacting with biological entities remains unexplored. Herein, we describe black (B)-TiO2@N/Au nanorobots interacting through photocatalytic pure water splitting-induced electrophoresis that exhibit periodic swarming oscillations under programmed near-infrared light. The periodic chemical-electric field generated by the oscillating B-TiO2@N/Au nanorobot swarm leads to local neuron activation in vitro. The field oscillations and neurotransmission from synchronized neurons further trigger the resonance oscillation of neuron populations without synaptic contact (about 2 mm spacing), in different ways from normal neuron oscillation requiring direct contact. We envision that the oscillating nanorobot swarm platforms will shed light on contactless communication of neurons and offer tools to explore interactions between neurons.

Molecular Thin Films Enable the Synthesis and Screening of Nanoparticle Megalibraries Containing Millions of Catalysts

Megalibraries are centimeter-scale chips containing millions of materials synthesized in parallel using scanning probe lithography. As such, they stand to accelerate how materials are discovered for applications spanning catalysis, optics, and more. However, a long-standing challenge is the availability of substrates compatible with megalibrary synthesis, which limits the structural and functional design space that can be explored. To address this challenge, thermally removable polystyrene films were developed as universal substrate coatings that decouple lithography-enabled nanoparticle synthesis from the underlying substrate chemistry, thus providing consistent lithography parameters on diverse substrates. Multi-spray inking of the scanning probe arrays with polymer solutions containing metal salts allows patterning of >56 million nanoreactors designed to vary in composition and size. These are subsequently converted to inorganic nanoparticles via reductive thermal annealing, which also removes the polystyrene to deposit the megalibrary. Megalibraries with mono-, bi-, and trimetallic materials were synthesized, and nanoparticle size was controlled between 5 and 35 nm by modulating the lithography speed. Importantly, the polystyrene coating can be used on conventional substrates like Si/SiO_x, as well as substrates typically more difficult to pattern on, such as glassy carbon, diamond, TiO_2, BN, W, or SiC. Finally, high-throughput materials discovery is performed in the context of photocatalytic degradation of organic pollutants using Au-Pd-Cu nanoparticle megalibraries on TiO₂ substrates with 2,250,000 unique composition/size combinations. The megalibrary was screened within 1 h by developing fluorescent thin-film coatings on top of the megalibrary as proxies for catalytic turnover, revealing Au_0.53Pd_0.38Cu_0.09-TiO₂ as the most active photocatalyst composition.

Functional Materials for Fabrication of Carbon-Based Perovskite Solar Cells: Ink Formulation and Its Effect on Solar Cell Performance

Perovskite solar cells (PSCs) have rapidly developed into one of the most attractive photovoltaic technologies, exceeding power conversion efficiencies of 25% and as the most promising technology to complement silicon-based solar cells. Among different types of PSCs, carbon-based, hole-conductor-free PSCs (C-PSCs), in particular, are seen as a viable candidate for commercialization due to the high stability, ease of fabrication, and low cost. This review examines strategies to increase charge separation, extraction, and transport properties in C-PSCs to improve the power conversion efficiency. These strategies include the use of new or modified electron transport materials, hole transport layers, and carbon electrodes. Additionally, the working principles of various printing techniques for the fabrication of C-PSCs are presented, as well as the most remarkable results obtained from each technique for small-scale devices. Finally, the manufacture of perovskite solar modules using scalable deposition techniques is discussed.

Improving the Electron Transport Performance of TiO2 Film by Regulating TiCl4 Post-Treatment for High-Efficiency Carbon-Based Perovskite Solar Cells

Titanium oxide (TiO₂ ) has been widely used as an electron transport layer (ETL) in perovskite solar cells (PSCs). Typically, TiCl₄ post-treatment is indispensable for modifying the surfaces of TiO₂ ETL to improve the electron transport performance. However, it is challenging to produce the preferred anatase phase-dominated TiO₂ by the TiCl₄ post-treatment due to the higher thermodynamic stability of the rutile phase. In this work, a mild continuous pH control strategy for effectively regulating the hydrolysis process of TiCl₄ post-treatment is proposed. As the weak organic base, urea has been demonstrated can maintain a moderate pH decrease during the hydrolysis process of TiCl₄ while keeping the hydrolysis process relatively mild due to the ultra-weak alkalinity. The improved pH environment is beneficial for the formation of anatase TiO₂ . Consequently, a uniform anatase-dominated TiO₂ surface layer is formed on the mesoporous TiO₂ , resulting in reduced defect density and superior band energy level. The interfacial charge recombination is effectively suppressed, and the charge extraction efficiency is improved simultaneously in the fabricated solar cells. The efficiency of the fabricated carbon electrode-based PSCs (C-PSCs) is improved from 16.63% to 18.08%, which is the highest for C-PSCs based on wide-bandgap perovskites.

Bio-inspired and metal-derived superwetting surfaces: Function, stability and applications

Due to their exceptional anti-icing, anti-corrosion, and anti-drag qualities, biomimetic metal-derived superwetting surfaces, which are widely employed in the aerospace, automotive, electronic, and biomedical industries, have raised significant concern. However, further applications in other domains have been hampered by the poor mechanical and chemical durability of superwetting metallic surfaces, which can result in metal fatigue and corrosion. The potential for anti-corrosion, anti-contamination, anti-icing, oil/water separation, and oil transportation on surfaces with superwettability has increased in recent years due to the advancement of research in biomimetic superwetting interface theory and practice. Recent developments in functionalized biomimetic metal-derived superwetting surfaces were summarized in this paper. Firstly, a detailed presentation of biomimetic metal-derived superwetting surfaces with unique capabilities was made. The problems with the long-term mechanical and chemical stability of biomimetic metal-derived superwetting surfaces were then examined, along with potential solutions. Finally, in an effort to generate fresh concepts for the study of biomimetic metal-derived superwetting surfaces, the applications of superwetting metallic surfaces in various domains were discussed in depth. The future direction of biomimetic metal-derived superwetting surfaces was also addressed.

Nonlinear optical response of graphene oxide quantum dots fabricated from electrospun polyacrylonitrile fibers

The nonlinear optical response of graphene oxide quantum dots (GOQDs) fabricated by the carbonization and exfoliation of electrospun polyacrylonitrile (PAN) fibers is reported. Electrospun and carbonized fibers were characterized by SEM and XPS. SEM micrograph confirmed the formation of PAN fibers of 153.44 ± 6.44 nm, while by XPS the binding energies associated with sp² and sp³ carbon hybridizations were found, after the carbonization process. On the other hand, the GOQDs obtained were characterized by photoluminescence (PL), UV-Vis, Raman spectroscopy, and High-Resolution Transmission Electron Microscopy (HRTEM). The GOQDs size of 10 nm was estimated by HRTEM. Raman spectroscopy showed the D and G bands associated with the sp² and sp³ hybridizations of the GOQDs, by PL two energy values of 2.67 and 2.97 eV were calculated. The UV-Vis spectrum showed two absorption bands confirming the presence of GOQDs. The nonlinear characterization was carried out using the P-scan technique, previously photodepositing GOQDs onto an optical fiber, using a coherent radiation source at a wavelength of 1550 nm. The results obtained showed a saturable absorption behavior with a value of β = - 2.474 × 10 - 4 m / W and a nonlinear susceptibility of χ ( 3 ) ≈ - 7.749 × 10 - 4 ( e s u ) . The results of this work showed that GOQDs obtained can be used for optical switching applications.

Solvothermal synthesis of soluble, surface modified anatase and transition metal doped anatase hybrid nanocrystals

Titanium dioxide, or titania, is perhaps the most well-known and widely studied photocatalytic material, with myriad applications, due to a high degree of tunability achievable through the incorporation of dopants and control of phase composition and particle size. Many of the applications of titanium dioxide require particular forms, such as gels, coatings, or thin films, making the development of hybrid solution processable nanoparticles increasingly attractive. Here we report a simple solvothermal route to highly dispersible anatase phase titanium dioxide hybrid nanoparticles from amorphous titania. Solvothermal treatment of the amorphous titania in trifluoroacetic acid leads to the formation of anatase phase nanoparticles with a high degree of size control and near complete surface functionalisation. This renders the particles highly dispersible in simple organic solvents such as acetone. Dopant ions may be readily incorporated into the amorphous precursor by co-precipitation, with no adverse effect on subsequent crystallisation and surface modification.

Recent Developments of Microscopic Study for Lanthanide and Manganese Doped Luminescent Materials

Luminescent materials are indispensable for applications in lighting, displays and photovoltaics, which can transfer, absorb, store and utilize light energy. Their performance is closely related with their size and morphologies, exact atomic arrangement, and local configuration about photofunctional centers. Advanced electron microscopy-based techniques have enabled the possibility to study nanostructures with atomic resolution. Especially, with the advanced micro-electro-mechanical systems, it is able to characterize the luminescent materials at the atomic scale under various environments, providing a deep understanding of the luminescent mechanism. Accordingly, this review summarizes the recent achievements of microscopic study to directly image the microstructure and local environment of activators in lanthanide and manganese (Ln/Mn²⁺ )-doped luminescent materials, including: 1) bulk materials, the typical systems are nitride/oxynitride phosphors; and 2) nanomaterials, such as nanocrystals (hexagonal-phase NaLnF₄ and perovskite) and 2D nanosheets (Ca₂ Ta₃ O₁₀ and MoS₂ ). Finally, the challenges and limitations are highlighted, and some possible solutions to facilitate the developments of advanced luminescent materials are provided.

Hydrothermal preparation of high purity TiO2 from industrial metatitanic acid by response surface methodology

The response surface methodology of Box Behnken design was used to investigate the effects of hydrothermal conditions on the high purity TiO2 preparation from industrial metatitanic acid. The method had a good fitting result in the prediction model, and the effects could be calculated from a second-order polynomial equation. The hydrothermal conditions greatly affected the structure and purity for the metatitanic acid and rutile TiO2, influenced the process of nucleation and crystallization, grain growth, polymerization, agglomeration and aggregation, further improved the particle size distribution, structure and surface adsorption capacity of metatitanic acid, reduced the adsorption of impurity ions, and finally improved the purity of TiO2. The variables such as hydrothermal temperature, slurry concentration and hydrothermal time had synergistic effects, and the effects of hydrothermal time were larger than the other two. The verification experiments confirmed that the predicted values could be achieved at 99.99% under the optimal hydrothermal conditions.

Tunable Ti3C2Tx MXene-Derived TiO2 Nanocrystals at Controlled pH and Temperature

While two-dimensional (2D) Ti₃C₂T_x MXene in aqueous dispersions spontaneously oxidizes into titanium dioxide (TiO₂) nanocrystals, the crystallization mechanism has not been comprehensively understood and the resultant crystal structures are not controlled among three representative polymorphs: anatase, rutile, and brookite. In this study, such control on the lattice structures and domain sizes of the MXene-derived TiO₂ crystallites is demonstrated by means of the oxidation conditions, pH, and temperature (3.0-11.0 and 20-100 °C, respectively). It is observed that the formation of anatase phase is preferred against rutile phase in more basic and hotter oxidizing solutions, and even 100% anatase can be obtained at pH 11.0 and 100 °C. At lower pH and temperature, the portion of rutile phase increases such that it reaches ∼70% at pH 3 and 20 °C. Under certain circumstances, small portion of brookite phase is also observed. Smaller domain sizes of both anatase and rutile phases are observed in more basic oxidizing solutions and at lower temperatures. Based on these experimental results, we propose the crystallization mechanism in which the oxidative dissociation of Ti₃C₂T_x first produces Ti ions as the intermediate state, and they bind to abundant oxygen in the aqueous dispersions, and nucleate and crystallize into TiO₂.

Reactivity of anatase (001) surface from first-principles many-body Green's function theory

The anatase (001) surface has attracted a lot of interest in surface science due to its excellent performance. However, its reactivity is under debate since it can undergo a (1 × 4) reconstruction. Herein, we applied the many-body Green's function theory to investigate the electronic properties and excitons as well as the water adsorption behavior of the (1 × 4) unreconstructed anatase (001) surface and two reconstructed patterns, namely ADM and AOM. Our results revealed that the high reactivity of the (001) surface is probably not relevant to the reconstructed shape. The unreconstructed (001) surface and reconstructed ADM surface were very reactive for dissociating H₂O molecules among three surfaces, but the lower-energy singlet exciton for ADM was completely confined within the inner atomic layers in TiO₂, which is unfavorable for hole transfer to the reactant on the surface. Also, the required photon energy for initiating photochemical reactions on the reconstructed ADM surface should be higher than for the unreconstructed (001) surface, implying it is more difficult for the reaction to happen on the former surface. The unreconstructed (001) surface exhibited the highest reactivity due to the smaller optical absorption edge and the photoholes distributed on surface sites.

The unreconstructed (001) surface seems to have superior reactivity than the reconstructed shapes.

The enhanced photocatalytic performance and first-principles computational insights of Ba doping-dependent TiO2 quantum dots

Degradation in the presence of visible light is essential for successfully removing dyes from industrial wastewater, which is pivotal for environmental and ecological safety. In recent years, photocatalysis has emerged as a prominent technology for wastewater treatment. This study aimed to improve the photocatalytic efficiency of synthesized TiO2 quantum dots (QDs) under visible light by barium (Ba) doping. For this, different weight ratios (2% and 4%) of Ba-doped TiO2 QDs were synthesized under ambient conditions via a simple and modified chemical co-precipitation approach. The QD crystal structure, functional groups, optical features, charge-carrier recombination, morphological properties, interlayer spacing, and presence of dopants were analyzed. The results showed that for 4% Ba-doped TiO2, the effective photocatalytic activity in the degradation process of methylene blue (MB) dye was 99.5% in an alkaline medium. Density functional theory analysis further corroborated that the band gap energy was reduced when Ba was doped into the TiO2 lattice, implying a considerable redshift of the absorption edge due to in-gap states near the valence band.

Recent Advances in Ferroelectric Materials-Based Photoelectrochemical Reaction

Inorganic perovskite ferroelectric-based nanomaterials as sustainable new energy materials, due to their intrinsic ferroelectricity and environmental compatibility, are intended to play a crucial role in photoelectrochemical field as major functional materials. Because of versatile physical properties and excellent optoelectronic properties, ferroelectric-based nanomaterials attract much attention in the field of photocatalysis, photoelectrochemical water splitting and photovoltaic. The aim of this review is to cover the recent advances by stating the different kinds of ferroelectrics separately in the photoelectrochemical field as well as discussing how ferroelectric polarization will impact functioning of photo-induced carrier separation and transportation in the interface of the compounded semiconductors. In addition, the future prospects of ferroelectric-based nanomaterials are also discussed.

Synthesis of innovative triphenylamine-functionalized organic photosensitizers outperformed the benchmark dye N719 for high-efficiency dye-sensitized solar cells

Herein, we present a thorough photovoltaic investigation of four triphenylamine organic sensitizers with D-π-A configurations and compare their photovoltaic performances to the conventional ruthenium-based sensitizer N719. SFA-5-8 are synthesized and utilized as sensitizers for dye-sensitized solar cell (DSSC) applications. The effects of the donor unit (triphenylamine), π-conjugation bridge (thiophene ring), and various acceptors (phenylacetonitrile and 2-cyanoacetamide derivatives) were investigated. Moreover, this was asserted by profound calculations of HOMO (highest occupied molecular orbital) and LUMO (lowest unoccupied molecular orbital) energy levels, the molecular electrostatic potential (MEP), and natural bond orbital (NBO) that had been studied for the TPA-sensitizers. Theoretical density functional theory (DFT) was performed to study the distribution of electron density between donor and acceptor moieties. The sensitization by the absorption of sensitizers SFA-5-8 leads to an obvious enhancement in the visible light absorption (300-750 nm) as well as a higher photovoltaic efficiency in the range of (5.53-7.56%). Under optimized conditions, SFA-7 showed outstanding sensitization of nanocrystalline TiO2, resulting in enhancing the visible light absorption and upgrading the power conversion efficiency (PCE) to approximately 7.56% over that reported for the N719 (7.29%). Remarkably, SFA-7 outperformed N719 by 4% in the total conversion efficiency. Significantly, the superior performance of SFA-7 could be mainly ascribed to the higher short-circuit photocurrents (Jsc) in parallel with larger open-circuit voltages (Voc) and more importantly, the presence of different anchoring moieties that could enhance the ability to fill the gaps on the surface of the TiO2 semiconductor. That could be largely reflected in the overall enhancement in the device efficiency. Moreover, the theoretical electronic and photovoltaic properties of all studied sensitizers have been compared with experimental results. All the 2-cyanoacrylamide derivative sensitizers demonstrated robust photovoltaic performance.

Light-Programmable Assemblies of Isotropic Micromotors

“Life-like” nonequilibrium assemblies are of increasing significance, but suffering from limited steerability as they are generally based on micro/nanomotors with inherent asymmetry in chemical composition or geometry, of which the vigorous random Brownian rotations disturb the local interactions. Here, we demonstrate that isotropic photocatalytic micromotors, due to the persistent phoretic flow from the illuminated to shadowed side irrespective of their Brownian rotations, experience light-programmable local interactions (reversibly from attraction to repulsion and/or alignment) depending on the direction of the incident lights. Thus, they can be organized into a variety of tunable nonequilibrium assemblies, such as apolar solids (i.e., immobile colloidal crystal), polar liquids (i.e., phototactic colloidal stream), and polar solids (i.e., phototactic colloidal crystal), which can further be “cut” into a predesigned pattern by utilizing the switching motor-motor interactions at superimposed-light edges. This work facilitates the development of active matters and motile functional microdevices.

Detection and Correction of Delocalization Errors for Electron and Hole Polarons Using Density-Corrected DFT

Modeling polaron defects is an important aspect of computational materials science, but the description of unpaired spins in density functional theory (DFT) often suffers from delocalization error. To diagnose and correct the overdelocalization of spin defects, we report an implementation of density-corrected (DC-)DFT and its analytic energy gradient. In DC-DFT, an exchange-correlation functional is evaluated using a Hartree-Fock density, thus incorporating electron correlation while avoiding self-interaction error. Results for an electron polaron in models of titania and a hole polaron in Al-doped silica demonstrate that geometry optimization with semilocal functionals drives significant structural distortion, including the elongation of several bonds, such that subsequent single-point calculations with hybrid functionals fail to afford a localized defect even in cases where geometry optimization with the hybrid functional does localize the polaron. This has significant implications for traditional workflows in computational materials science, where semilocal functionals are often used for structure relaxation. DC-DFT calculations provide a mechanism to detect situations where delocalization error is likely to affect the results.

Role of Surface Coverage and Film Quality of the TiO2 Electron Selective Layer for Optimal Hole-Blocking Properties

Titanium dioxide (TiO2) is a commonly used electron selective layer in thin-film solar cells. The energy levels of TiO2 align well with those of most light-absorbing materials and facilitate extracting electrons while blocking the extraction of holes. In a device, this separates charge carriers and reduces recombination. In this study, we have evaluated the hole-blocking behavior of TiO2 compact layers using charge extraction by linearly increasing voltage in a metal-insulator-semiconductor structure (MIS-CELIV). This hole-blocking property was characterized as surface recombination velocity (S R) for holes at the interface between a semiconducting polymer and TiO2 layer. TiO2 layers of different thicknesses were prepared by sol-gel dip coating on two transparent conductive oxide substrates with different roughnesses. Surface coverage and film quality on both substrates were characterized using X-ray photoelectron spectroscopy and atomic force microscopy, along with its conductive imaging mode. Thicker TiO2 coatings provided better surface coverage, leading to reduced S R, unless the layers were otherwise defective. We found S R to be a more sensitive indicator of the overall film quality, as varying S R values were still observed among the films that looked similar in their characteristics via other methods.

Plasmon-assisted nanophase engineering of titanium dioxide for improved performances in single-particle based sensing and photocatalysis

Titanium dioxide (TiO₂) due to its large bandgap, has a very limited efficiency in utilizing sunlight for photocatalysis and photoanode applications. Sensitizing with metallic nanoparticles is one of the promising routes for resolving this issue but it requires thermal annealing and proper bandgap engineering to optimize the Schottky junctions. Here we use plasmonic nanoheating to locally anneal the TiO₂ medium with a sub-nanometer (sub-nm) feature, which results in a nanophase transition from amorphous TiO₂ to anatase and rutile with a gradient configuration. Such gradient nanocoatings of rutile/anatase establish a cascade hot electron transfer via a conduction band and defect states, which improves the surface enhanced Raman scattering (SERS) performance and photocatalytic efficiency over an order of magnitude. Unlike conventional global annealing, this nanoannealing strategy with plasmonic heating enables sub-nm control at the interface between the metal and semiconductors, and this strategy not only provides new opportunities for single particle SERS, but also shows significant implications for photocatalysis and hot-electron chemistry.

Withania somnifera: Progress towards a Pharmaceutical Agent for Immunomodulation and Cancer Therapeutics

Chemotherapy is one of the prime treatment options for cancer. However, the key issues with traditional chemotherapy are recurrence of cancer, development of resistance to chemotherapeutic agents, affordability, late-stage detection, serious health consequences, and inaccessibility. Hence, there is an urgent need to find innovative and cost-effective therapies that can target multiple gene products with minimal adverse reactions. Natural phytochemicals originating from plants constitute a significant proportion of the possible therapeutic agents. In this article, we reviewed the advances and the potential of Withania somnifera (WS) as an anticancer and immunomodulatory molecule. Several preclinical studies have shown the potential of WS to prevent or slow the progression of cancer originating from various organs such as the liver, cervix, breast, brain, colon, skin, lung, and prostate. WS extracts act via various pathways and provide optimum effectiveness against drug resistance in cancer. However, stability, bioavailability, and target specificity are major obstacles in combination therapy and have limited their application. The novel nanotechnology approaches enable solubility, stability, absorption, protection from premature degradation in the body, and increased circulation time and invariably results in a high differential uptake efficiency in the phytochemical’s target cells. The present review primarily emphasizes the insights of WS source, chemistry, and the molecular pathways involved in tumor regression, as well as developments achieved in the delivery of WS for cancer therapy using nanotechnology. This review substantiates WS as a potential immunomodulatory, anticancer, and chemopreventive agent and highlights its potential use in cancer treatment.

Detection and Characterization of TiO2 Nanomaterials in Sludge from Wastewater Treatment Plants of Chihuahua State, Mexico

TiO₂ nanoparticles (TiO₂-NPs) have a wide range of industrial applications (paintings, sunscreens, food and cosmetics) and is one of the most intensively used nanomaterials worldwide. Leaching from commercial products TiO₂-NPs are predicted to significantly accumulate in wastewater sludges, which are then often used as soil amendment. In this work, sludge samples from four wastewater treatment plants of the Chihuahua State in Mexico were obtained during spring and summer (2017). A comprehensive characterization study was performed by X-ray based (laboratory and synchrotron) techniques and electron microscopy. Ti was detected in all sludge samples (1810–2760 mg/kg) mainly as TiO₂ particles ranging from 40 nm up to hundreds of nm. Micro-XANES data was analyzed by principal component analysis and linear combination fitting enabling the identification of three predominant Ti species: anatase, rutile and ilmenite. Micro-XANES from the smaller Ti particles was predominantly anatase (68% + 32% rutile), suggesting these TiO₂-NPs originate from paintings and cosmetics. TEM imaging confirmed the presence of nanoscale Ti with smooth surface morphologies resembling engineered TiO₂-NPs. The size and crystalline phase of TiO₂-NPs in the sludge from this region suggest increased reactivity and potential toxicity to agro-systems. Further studies should be dedicated to evaluating this.

Synthesis and Characterization of Anatase TiO2 Nanorods: Insights from Nanorods’ Formation and Self-Assembly

Highly crystalline, organic-solvent-dispersible titanium dioxide (TiO2) nanorods (NRs) present promising chemicophysical properties in many diverse applications. In this paper, based on a modified procedure from literature, TiO2 NRs were synthesized via a ligand-assisted nonhydrolytic sol-gel route using oleic acid as the solvent, reagent, and ligand and titanium (IV) isopropoxide as the titanium precursor. This procedure produced monodisperse TiO2 NRs, as well as some semi-spherical titania nanocrystals (NCs) that could be removed by size-selective precipitation. X-ray diffraction and selected area electron diffraction results showed that the nanorods were anatase, while the semipheres also contained the TiO2(B) phase. By taking samples during the particle growth, it was found that the average length of the initially grown NRs decreased during the synthesis. Possible reasons for this unusual growth path, partially based on high-resolution transmission electron microscopy (HRTEM) observations during the growth, were discussed. The dispersion of anatase TiO2 nanorods was capable of spontaneous formation of lyotropic liquid crystals on the TEM grid and in bulk. Considering high colloidal stability together with the large optical birefringence displayed by these high refractive index liquid crystalline domains, we believe these TiO2 NRs dispersions are promising candidates for application in transparent and switchable optics.

Prediction of stable silver selenide-based energy materials sustained by rubidium selenide alloying

Silver selenide (Ag2Se) is a ductile material with a low lattice thermal conductivity that can be a valuable substitute for both PbSe and Bi2Se3 for Pb toxicity free and Bi scarcity.

Global distribution, genesis, exploitation, applications, production, and demand of industrial heavy minerals

Heavy minerals (HMs) are used in many high-tech applications (e.g. nuclear reactors, photovoltaic cells, electronics, green, and nano- and space technology), and thus global demand is increasing day by day. This review article is focused on the global distribution, genesis, economic geology, exploration and exploitation, demand (i.e. past, present, and future status of annual global production, consumption, and price), applications (geological and industrial uses), and major environmental issues mostly related to the HM sand industry. Heavy mineral deposits are distributed in more than 45 countries. Major HM deposits are located in Australia, Asia, and Africa, as secondary coastal placers bordering the Indian Ocean. Onshore and offshore deposits in the Americas, Europe, and other countries also contribute to the global HM market. Heavy mineral deposits are categorised as primary (magmatic, hydrothermal, metamorphic) or secondary (weathered, eroded, and transported sediments) deposits. Titanium, zirconium, and rare earth element (REEs) bearing minerals are key industrial commodities in the current global market. The heavy mineral industry has experienced healthy growth in unit price and global production due to increased demand generated by rapidly expanding economies such as those of China and India. Global production of zircon, ilmenite, and rutile has gradually increased over the last few decades. Global apparent consumption of ilmenite declined slightly from 1970 to 1995, in part due to introduction of stringent regulatory measures and government environmental policies in Europe and North America, as the main consumers of HMs at present. Mining and utilisation planning following the United Nations Sustainable Development Goals are highly appropriate for the sustainability of the HM industry, and to overcome ecological challenges, health issues, and social resistance towards HM exploitation. Finally, we forecast changes in production and price of three HMs (ilmenite, rutile, and zircon) for the decade from 2020 to 2030, assuming there are no disturbances in production due to external factors such as the Covid-19 global pandemic or unfavourable geopolitical interventions.

Synergic fabrication of succimer coated titanium dioxide nanomaterials delivery for in vitro proliferation and in vivo examination on human aortic endothelial cells

The probable nanotoxicity to human health and the environment is a significant challenge for the sustainable application of nanomaterials in medicine. The cytototoxical effect of succimer (meso-2,3-dimercaptosuccinic acid-DMSA) coated titanium dioxide (DMSA-TiO2) with cultured human aortic endothelial cells (HAoECs) was assessed in this investigation. Our findings have shown that DMSA-TiO2 can be accumulated in HAoECs and dispersed in a cytoplasm on the culture medium. DMSA-cytotoxicity TiO2 effects were dose-responsive, and the concentrations were of little toxicity, and MTT stain testing showed that they had only 0.02 mg ml-1. Meanwhile, the lactate dehydrogenase biomarker was not considerably more remarkable than the biomarker from untreated (control) cells (free DMSA-TiO2). Though, also without any apparent signs of cell damage, the endocrine functions for prostacyclin I-2 and endothelin-1 and the urea transporter functions were modified. In addition, in vitro endothelial tube development has been shown that HAoECs could induce angiogenesis even with small amounts of DMSA-TiO2 (0.01 and 0.02 mg ml-1). Further, we have examined the in vivo toxicity and biochemical parameter by animal model. Furthermore, in vivo assessments designated that the resulting DMSA-TiO2 presented synergistic activities of angiogenesis activity. Overall, these findings show the cytotoxicity of DMSA-TiO2 and could induce adverse effects on normal endothelial cells.

Unveiling the Electronic Structure of Grain Boundaries in Anatase with Electron Microscopy and First-Principles Modeling

Polycrystalline anatase titanium dioxide has drawn great interest, because of its potential applications in high-efficiency photovoltaics and photocatalysts. There has been speculation on the electronic properties of grain boundaries but little direct evidence, because grain boundaries in anatase are challenging to probe experimentally and to model. We present a combined experimental and theoretical study of anatase grain boundaries that have been fabricated by epitaxial growth on a bicrystalline substrate, allowing accurate atomic-scale models to be determined. The electronic structure in the vicinity of stoichiometric grain boundaries is relatively benign to device performance but segregation of oxygen vacancies introduces barriers to electron transport, because of the development of a space charge region. An intrinsically oxygen-deficient boundary exhibits charge trapping consistent with electron energy loss spectroscopy measurements. We discuss strategies for the synthesis of polycrystalline anatase in order to minimize the formation of such deleterious grain boundaries.