Nitrogen-Doped Titanium Dioxide as Visible-Light-Sensitive Photocatalyst: Designs, Developments, and Prospects

Nitrogen-doped titanium dioxide/schwertmannite nanocomposites as heterogeneous photo-Fenton catalysts with enhanced efficiency for the degradation of bisphenol A

Potential health risks related to environmental endocrine disruptors (EEDs) have aroused research hotspots at the forefront of water treatment technologies. Herein, nitrogen-doped titanium dioxide/schwertmannite nanocomposites (N-TiO2/SCH) have been successfully developed as heterogeneous catalysts for the degradation of typical EEDs via photo-Fenton processes. Due to the sustainable Fe(III)/Fe(II) conversion induced by photoelectrons, as-prepared N-TiO2/SCH nanocomposites exhibit much enhanced efficiency for the degradation of bisphenol A (BPA; ca. 100% within 60 min under visible irradiation) in a wide pH range of 3.0-7.8, which is significantly higher than that of the pristine schwertmannite (ca. 74.5%) or N-TiO2 (ca. 10.8%). In this photo-Fenton system, the efficient degradation of BPA is mainly attributed to the oxidation by hydroxyl radical (•OH) and singlet oxygen (1O2). Moreover, the possible catalytic mechanisms and reaction pathway of BPA degradation are systematically investigated based on analytical and photoelectrochemical analyses. This work not only provides a feasible means for the development of novel heterogeneous photo-Fenton catalysts, but also lays a theoretical foundation for the potential application of mineral-based materials in wastewater treatment.

Recent Progress of Ion-Modified TiO2 for Enhanced Photocatalytic Hydrogen Production

Harnessing solar energy to produce hydrogen through semiconductor-mediated photocatalytic water splitting is a promising avenue to address the challenges of energy scarcity and environmental degradation. Ever since Fujishima and Honda's groundbreaking work in photocatalytic water splitting, titanium dioxide (TiO2) has garnered significant interest as a semiconductor photocatalyst, prized for its non-toxicity, affordability, superior photocatalytic activity, and robust chemical stability. Nonetheless, the efficacy of solar energy conversion is hampered by TiO2's wide bandgap and the swift recombination of photogenerated carriers. In pursuit of enhancing TiO2's photocatalytic prowess, a panoply of modification techniques has been explored over recent years. This work provides an extensive review of the strategies employed to augment TiO2's performance in photocatalytic hydrogen production, with a special emphasis on foreign dopant incorporation. Firstly, we delve into metal doping as a key tactic to boost TiO2's capacity for efficient hydrogen generation via water splitting. We elaborate on the premise that metal doping introduces discrete energy states within TiO2's bandgap, thereby elevating its visible light photocatalytic activity. Following that, we evaluate the role of metal nanoparticles in modifying TiO2, hailed as one of the most effective strategies. Metal nanoparticles, serving as both photosensitizers and co-catalysts, display a pronounced affinity for visible light absorption and enhance the segregation and conveyance of photogenerated charge carriers, leading to remarkable photocatalytic outcomes. Furthermore, we consolidate perspectives on the nonmetal doping of TiO2, which tailors the material to harness visible light more efficiently and bolsters the separation and transfer of photogenerated carriers. The incorporation of various anions is summarized for their potential to propel TiO2's photocatalytic capabilities. This review aspires to compile contemporary insights on ion-doped TiO2, propelling the efficacy of photocatalytic hydrogen evolution and anticipating forthcoming advancements. Our work aims to furnish an informative scaffold for crafting advanced TiO2-based photocatalysts tailored for water-splitting applications.

A Facile Strategy for the Preparation of N-Doped TiO2 with Oxygen Vacancy via the Annealing Treatment with Urea

Although titanium dioxide (TiO2) has a wide range of potential applications, the photocatalytic performance of TiO2 is limited by both its limited photoresponse range and fast recombination of the photogenerated charge carriers. In this work, the preparation of nitrogen (N)-doped TiO2 accompanied by the introduction of oxygen vacancy (Vo) has been achieved via a facile annealing treatment with urea as the N source. During the annealing treatment, the presence of urea not only realizes the N-doping of TiO2 but also creates Vo in N-doped TiO2 (N-TiO2), which is also suitable for commercial TiO2 (P25). Unexpectedly, the annealing treatment-induced decrease in the specific surface area of N-TiO2 is inhibited by the N-doping and, thus, more active sites are maintained. Therefore, both the N-doping and formation of Vo as well as the increased active sites contribute to the excellent photocatalytic performance of N-TiO2 under visible light irradiation. Our work offers a facile strategy for the preparation of N-TiO2 with Vo via the annealing treatment with urea.

Synthesis and preliminary evaluation of Ag-TiO2/CNT hybrid nanocomposite for the degradation of polystyrene microplastics under solar irradiation

Currently, microplastics (MPs) are considered as emerging aqueous pollutants. However, existing methods for the separation and treatment of MPs from an aquatic environment are limited by their low efficiency. Advanced oxidation processes (AOPs) are novel techniques that employ photo-induced electron/hole pairs to generate active radicals for MP mineralization. Thus, in this study, a photocatalyst, i.e., Ag+ ion-doped TiO2, heterojunctioned with carbon nanotubes (CNT), was synthesized to study the degradation of typical MPs such as polystyrene (PS) under solar irradiation. Effectiveness of the prepared photocatalyst for the PS degradation was estimated through FESEM, FTIR, total organic carbon (TOC) analyzer, and gas chromatography-mass spectroscopy (GC-MS). Quantitatively, 31.7% degradation of PS microbeads was achieved within 48 h. Therefore, this study provides an efficient and cost-effective strategy for the degradation of MPs from the aqueous medium.

Interfacial Electronic States of GeC/g-C3N4 van der Waal Heterostructure with Promising Photocatalytic Activity via Hydrogenation

The bandgap of most known two-dimensional materials can be tuned by hydrogenation, although certain 2D materials lack a sufficient wide bandgap. Currently, it would be perfect to design non-toxic, low-cost, and high-performance photocatalysts for photocatalytic water splitting via hydrogenation. We systematically examine the impact of hydrogenation on the optical and electronic characteristics of GeC/g-C3N4 vdW heterostructures (vdWHs) with four different stacking patterns using first-principles calculations. The phonon spectra, interlayer distance, binding energies and ab initio molecular dynamics calculations show the kinetic, mechanical, and thermal stability of GeC/g-C3N4 vdWH after hydrogenation at 300, 500 and 800 K and possesses anisotropic Poisson's ratio, Young's and bulk modulus, suggesting that it's a promising candidate for experimental fabrication. According to an investigation of its electronic properties, GeC/g-C3N4 vdWH has a bandgap of 1.28 eV, but hydrogenation dramatically increases it to 2.47 eV. As a result of interface-induced electronic doping, the electronic states in g-C3N4 might be significantly adjusted by coming into contact with hydrogenated GeC sheets. The vdWH exhibits a type-II semiconductor, which can enhance the spatial separation of electron-hole pairs and has a strong red-shift of absorption coefficient than those of the constituent monolayers. The high potential drop caused by the significant valence and conduction band offsets effectively separated the charge carriers. The absorption coefficient of GeCH2/g-C3N4 vdWH is highly influenced by a biaxial compressive strain more than the biaxial tensile strain. Our theoretical research implies that the hydrogenated GeCH2/g-C3N4 vdWH possesses tunable optical and electronic behaviour for use as a hole-transport material in solar energy harvesting, nanoelectronic and optoelectronic devices.

Enhancing air treatment through controlled fabrication of transition metal-doped titanium dioxide nanocomposites for photocatalytic toluene degradation

Rapid industrial growth and urbanization have resulted in a significant rise in environmental pollution issues, particularly indoor air pollutants. As a result, it is crucial to design and develop technologies and/or catalysts that are not only cost-effective but also promising high performance and practical applicability. However, achieving this goal has been so far remained a challenging task. Herein, a series of transition metal M - TiO2 (M = W, Fe, Mn) nanocrystals was prepared for photocatalytic degradation of volatile organic compounds (VOCs), i.e., toluene. Of the nanocomposites tested, W-TiO2 showed significantly improved photocatalytic activity for VOC degradation under UV irradiation compared to the others. In particular, the optimized W dopant amount of 0.5 wt% resulted in the outstanding degradation performance of toluene (96%) for the obtained W-TiO2(0.5%) nanocomposite. Moreover, W-TiO2(0.5%) nanocomposite exhibited good stability for 32 h working under high toluene concentration (10 ppm) compared to the pristine TiO2. The current work demonstrates the potential usage of M - TiO2 nanocrystals, particularly W-TiO2(0.5%), as a promising photocatalyst for efficient VOCs degradation.

Charge transfer in TiO2-based photocatalysis: fundamental mechanisms to material strategies

Semiconductor-based photocatalysis has attracted significant interest due to its capacity to directly exploit solar energy and generate solar fuels, including water splitting, CO2 reduction, pollutant degradation, and bacterial inactivation. However, achieving the maximum efficiency in photocatalytic processes remains a challenge owing to the speedy recombination of electron-hole pairs and the limited use of light. Therefore, significant endeavours have been devoted to addressing these issues. Specifically, well-designed heterojunction photocatalysts have been demonstrated to exhibit enhanced photocatalytic activity through the physical distancing of electron-hole pairs generated during the photocatalytic process. In this review, we provide a systematic discussion ranging from fundamental mechanisms to material strategies, focusing on TiO2-based heterojunction photocatalysts. Current efforts are focused on developing heterojunction photocatalysts based on TiO2 for a variety of photocatalytic applications, and these projects are explained and assessed. Finally, we offer a concise summary of the main insights and challenges in the utilization of TiO2-based heterojunction photocatalysts for photocatalysis. We expect that this review will serve as a valuable resource to improve the efficiency of TiO2-based heterojunctions for energy generation and environmental remediation.

Recent developments, advances and strategies in heterogeneous photocatalysts for water splitting

Photocatalytic water splitting (PWS) is an up-and-coming technology for generating sustainable fuel using light energy. Significant progress has been made in the developing of PWS innovations over recent years. In addition to various water-splitting (WS) systems, the focus has primarily been on one- and two-steps-excitation WS systems. These systems utilize singular or composite photocatalysts for WS, which is a simple, feasible, and cost-effective method for efficiently converting prevalent green energy into sustainable H2 energy on a large commercial scale. The proposed principle of charge confinement and transformation should be implemented dynamically by conjugating and stimulating the photocatalytic process while ensuring no unintentional connection at the interface. This study focuses on overall water splitting (OWS) using one/two-steps excitation and various techniques. It also discusses the current advancements in the development of new light-absorbing materials and provides perspectives and approaches for isolating photoinduced charges. This article explores multiple aspects of advancement, encompassing both chemical and physical changes, environmental factors, different photocatalyst types, and distinct parameters affecting PWS. Significant factors for achieving an efficient photocatalytic process under detrimental conditions, (e.g., strong light absorption, and synthesis of structures with a nanometer scale. Future research will focus on developing novel materials, investigating potential synthesis techniques, and improving existing high-energy raw materials. The endeavors aim is to enhance the efficiency of energy conversion, the absorption of radiation, and the coherence of physiochemical processes.

Chemically Engineered Titanium Oxide Interconnecting Layer for Multijunction Polymer Solar Cells

We report chemically tunable n-type titanium oxides using ethanolamine as a nitrogen dopant source. As the amount of ethanolamine added to the titanium oxide precursor during synthesis increases, the Fermi level of the resulting titanium oxides (ethanolamine-incorporated titanium oxides) significantly changes from -4.9 eV to -4.3 eV, and their free charge carrier densities are enhanced by two orders of magnitudes, reaching up to 5 × 1018 cm-3. Unexpectedly, a basic ethanolamine reinforces not only the n-type properties of titanium oxides, but also their basicity, which facilitates acid-base ionic junctions in contact with acidic materials. The enhanced charge carrier density and basicity of the chemically tuned titanium oxides enable multi-junction solar cells to have interconnecting junctions consisting of basic n-type titanium oxides and acidic p-type PEDOT:PSS to gain high open-circuit voltages of 1.44 V and 2.25 V from tandem and triple architectures, respectively.

High-throughput experimentation for photocatalytic water purification in practical environments

High-throughput screening instrument was developed for photocatalytic water purification, enabling the simultaneous testing of 132 photocatalytic reactions under uniform visible light irradiation, temperature control, and stirring. The instrument was used to investigate the effects of different catalysts (TiO2, ZnO, α-Fe2O3) and environmental waters (seawater, urban wastewater, and industrial wastewater) on dye degradation. It was observed environmental ions, particularly carbonate and phosphate ions, significantly reduced catalyst activity by inhibiting the adsorption of dye molecules. To develop effective catalysts for dye degradation in industrial wastewater, 15 types of noble metal nanoparticles (NPs) were supported on photocatalysts. The study found that noble metal NPs with high work functions and oxidation resistance, such as Au and Pt, exhibited higher activity even in the industrial wastewater, likely converting environmental ions into active species. These findings, based on 432 test results, demonstrate the effectiveness of the developed high-throughput screening instrument for optimizing photocatalytic water purification.

New Transition Metal Coordination Polymers Derived from 2-(3,5-Dicarboxyphenyl)-6-carboxybenzimidazole as Photocatalysts for Dye and Antibiotic Decomposition

Coordination polymers (CPs) are an assorted class of coordination complexes that are gaining attention for the safe and sustainable removal of organic dyes from wastewater discharge by either adsorption or photocatalytic degradation. Herein, three different coordination polymers with compositions [Ni(HL)(H2O)2·1.9H2O] (1), [Mn3(HL)(L)(μ3-OH)(H2O)(phen)2·2H2O] (2), and [Cd(HL)4(H2O)]·H2O (3) (H3L = 2-(3,5-dicarboxyphenyl)-6-carboxybenzimidazole; phen = 1,10-phenanthroline) have been synthesized and characterized spectroscopically and by single crystal X-ray diffraction. Single crystal X-ray diffraction results indicated that 1 forms a 2D layer-like framework, while 2 exhibits a 3-connected net with the Schläfli symbol of (44.6), and 3 displays a 3D supramolecular network in which two adjacent 2D layers are held by π···π interactions. All three compounds have been used as photocatalysts to catalyze the photodegradation of antibiotic dinitrozole (DTZ) and rhodamine B (RhB). The photocatalytic results suggested that the Mn-based CP 2 exhibited better photodecomposition of DTZ (91.1%) and RhB (95.0%) than the other two CPs in the time span of 45 min. The observed photocatalytic mechanisms have been addressed using Hirshfeld surface analyses.

Ru(N^N)3-docked cationic covalent organic frameworks for enhanced sulfide and amine photooxidation

Covalent organic frameworks (COFs) have emerged as significant candidates for visible-light photocatalysis due to their ability to regulate performance which is achieved through the careful selection of building modules, framework conjugation, and post-modification. This report focused on the efficient transformation of an imine-linked I-COF into a π-conjugated quinoline-based Q-COF, which enhanced both the chemical stability and conjugation of the network. By methylating the pyridyl groups in the Q-COF, an N+-COF was obtained. Subsequently, the Ru(N^N)3-photosensitizer ([Ru(dcbpy)3]4-) was incorporated into the channels of the cationic N+-COF through electrostatic interactions, resulting in the formation of [Ru(dcbpy)3]4-⊂N+-COF. This composite exhibited exceptional photocatalytic activity, demonstrating high yields and selectivity in the oxidation of sulfides or amines to their respective products.

Topochemical Fluorination of LaBaInO4 to LaBaInO3F2, Their Optical Characterization, and Photocatalytic Activities for Hydrogen Evolution

We report on a nonoxidative topochemical route for the synthesis of a novel indate-based oxyfluoride, LaBaInO3F2, using a low-temperature reaction of Ruddlesden-Popper-type LaBaInO4 with polyvinylidene difluoride as a fluorinating agent. The reaction involves the replacement of oxide ions with fluoride ions as well as the insertion of fluoride ions into the interstitial sites. From the characterization via powder X-ray diffraction (PXRD) and Rietveld analysis as well as automated electron diffraction tomography (ADT), it is deduced that the fluorination results in a symmetry lowering from I4/mmm (139) to monoclinic C2/c (15) with an expansion perpendicular to the perovskite layers and a strong tilting of the octahedra in the ab plane. Disorder of the anions on the apical and interstitial sites seems to be favored. The most stable configuration for the anion ordering is estimated based on an evaluation of bond distances from the ADT measurements via bond valence sums (BVSs). The observed disordering of the anions in the oxyfluoride results in changes in the optical properties and thus shows that the topochemical anion modification can present a viable route to alter the optical properties. Partial densities of states (PDOSs) obtained from ab initio density functional theory (DFT) calculations reveal a bandgap modification upon fluoride-ion introduction which originates from the presence of the oxide anions on the interstitial sites. The photocatalytic performance of the oxide and oxyfluoride shows that both materials are photocatalytically active for hydrogen (H2) evolution.

Solvothermal synthesis of 3D rod-shaped Ti/Al/Cr nano-oxide for photodegradation of wastewater micropollutants under sunlight: a green way to achieve SDG:6

Waterbodies are day-by-day polluted by the various colored micropollutants, e.g., azo dyes enriched (carcinogenic, non-biodegradable) colored wastewater from textile industries. Water pollution has become a serious global issue as ~ 25% of health diseases are prompted by pollution as reported by WHO. Around 1 billion people will face water scarcity by 2025 and this water crisis is also a prime focus to the UNs' sustainable development goal 6 (SDG6: clean water and sanitation). To prevent the water pollution caused by micropollutants, a mesoporous, 3D rod-like nano-oxide Ti/Al/Cr (abbreviated as TAC) has been synthesized via the solvothermal method. TAC degraded all classes of azo dyes (mono, di, tri, etc.) with > 90% efficiency under renewable energy source solar irradiation within the pH range 2-11. The detailed study was done on the photodegradation of carcinogenic di-azo dye Congo red (CR) which is banned in many countries. TAC showed 90.64 ± 2% degradation efficiency for CR at pH 7. The proposed photodegradation mechanism of CR was confirmed by the high-resolution liquid chromatography-mass spectroscopy (HRLC-MS) analysis obeying the Pirkanniemi path. The photodegradation obeyed the pseudo-1st-order kinetics and was reusable up to successive 5 cycles which can be an efficient tool to meet the UNs' SDG:6.

Spent Coffee Grounds Derived Carbon Loading C, N Doped TiO2 for Photocatalytic Degradation of Organic Dyes

Titanium dioxide (TiO₂) is an ideal photocatalyst candidate due to its high activity, low toxicity and cost, and high chemical stability. However, its practical application in photocatalysis is seriously hindered by the wide band gap energy of TiO₂ and the prone recombination of electron-hole pairs. In this study, C, N doped TiO₂ were supported on spent coffee grounds-derived carbon (ACG) via in situ formation, which was denoted as C, N-TiO₂@ACG. The obtained C, N-TiO₂@ACG exhibits increased light absorption efficiency with the band gap energy decreasing from 3.31 eV of TiO₂ to 2.34 eV, a higher specific surface area of 145.8 m²/g, and reduced recombination rates attributed to the synergistic effect of a spent coffee grounds-derived carbon substrate and C, N doping. Consequently, the optimal 1:1 C, N-TiO₂@ACG delivers considerable photocatalytic activity with degradation efficiencies for methylene blue (MB) reaching 96.9% within 45 min, as well as a high reaction rate of 0.06348 min^-1, approximately 4.66 times that of TiO₂ (0.01361 min^-1). Furthermore, it also demonstrated greatly enhanced photocatalytic efficiency towards methyl orange (MO) in the presence of MB compared with a single MO solution. This work provides a feasible and universal strategy of synchronous introducing nonmetal doping and biomass-derived carbon substrates to promote the photocatalytic performance of TiO₂ for the degradation of organic dyes.

Selective Thermal and Photocatalytic Decomposition of Aqueous Hydrazine to Produce H2 over Ag-Modified TiO2 Nanomaterial

An Ag-modified TiO₂ nanomaterial was prepared by a one-pot synthesis method using tetra butyl titanate, silver nitrate, and sodium hydroxide in water at 473 K for 3 h. X-ray diffraction, scanning electron microscopy, and transmission electron microscopy were used to determine the structure and morphology of the synthesized Ag-modified TiO₂ nanomaterial. The diffuse reflectance UV-visible and photoluminescence spectroscopy results revealed that metallic Ag nanoparticles decreased the optical band gap and photoluminescence intensity of the TiO₂. In addition, the Raman peak intensity and absorbance were increased after Ag modification onto TiO₂. The photocatalytic efficiency of the synthesized samples was tested for decomposition of aqueous hydrazine solution under visible light irradiation. The photocatalytic efficiency of Ag-modified TiO₂ nanomaterials was higher than that of bare TiO₂ and Ag metal NPs due to the synergistic effect between the Ag metal and TiO₂ structures. In addition, the surface plasmon resonance (SPR) electron transfer from Ag metal particles to the conduction band of TiO₂ is responsible for superior activity of TiO₂-Ag catalyst. The Ag-modified TiO₂ nanomaterials offered a 100% H₂ selectivity within 30 min of reaction time and an apparent rate constant of 0.018 min^-1 with an activation energy of 34.4 kJ/mol under visible light radiation.

Sputter -coated N-enriched mixed metal oxides (Ta2O5-Nb2O5-N) composite: A resilient solar driven photocatalyst for water purification

This study demonstrated the formation of N-enriched mixed metal oxides (Ta₂O₅-Nb₂O₅-N and Ta₂O₅-Nb₂O₅) thin film composites used as photocatalysts to degrade P-Rosaniline Hydrochloride (PRH-Dye) dye under solar radiation. By controlling the N gas flow rate during the sputtering process, the N concentration in the Ta₂O₅-Nb₂O₅-N composite is significantly included, and demonstrated by XPS and HRTEM analysis. With the help of XPS and HRTEM investigations, it was determined that the addition of N to Ta₂O₅-Nb₂O₅-N significantly enhances the active sites. The Ta-O-N bond (N 1 s and Ta 4p_3/2 spectra) was verified by the XPS spectra. Ta₂O₅-Nb₂O₅ was found to have a lattice interplanar distance (d-spacing) of 2.52, whereas Ta₂O₅-Nb₂O₅-N showed the 2.5 (620 planes). A sputter-coated Ta₂O₅-Nb₂O₅and Ta₂O₅-Nb₂O₅-N photocatalysts were prepared, and their photocatalytic activity was evaluated using PRH-Dye as a model pollutant under solar radiation by adding H₂O₂ (0.01 mol). The photocatalytic activity of the Ta₂O₅-Nb₂O₅-N composite was compared with TiO₂ (P-25) and Ta₂O₅-Nb₂O₅. Ta₂O₅-Nb₂O₅-N showed very high photocatalytic activity compared to Degussa P-25 TiO₂ and Ta₂O₅-Nb₂O₅ under solar radiation and confirmed the presence of N in Ta₂O₅-Nb₂O₅-N significantly increased the generation of ˙OH radicals (in pH 3, 7 and 9). With the use of LC/MS, the stable intermediates or metabolite created during the photooxidation of PRH-Dye were assessed. The results of this study will provide useful insights on how Ta₂O₅-Nb₂O₅-N influences the efficiency of water pollution remediation.

Skin B/N-doped anatase TiO2 {001} nanoflakes for visible-light photocatalytic water oxidation

The limited visible-light-responsive photoactivities of most doped wide-bandgap photocatalysts with widened absorption range have long been the obstacles for the efficient conversion of solar energy to chemical energy by photocatalysis. The weak transport ability of visible-light-induced low-energy charge carriers, and numerous recombination centers arising from the energy-band modifiers along the transport path are two major factors responsible for such a mismatch. A potential solution is to shorten the transport path of photo-induced charges in well-modulated light absorbers with low-dimensional structure and the spatially concentrated dopants underneath their surfaces. As a proof of concept, skin B/N-doped red anatase TiO₂ {001} nanoflakes with the absorption edge up to 675 nm were synthesized in this study. Experimental results revealed that boron dopants in the TiO₂ nanoflakes from the hydrolysis of nanosized TiB₂ played a crucial role in controlling nitrogen doping in the surface layer of the nanoflakes. As visible light excitation occurs at the surface layer, the photons can be sufficiently absorbed by the formed energy levels at the surface layers, and the photogenerated charge carriers can effectively migrate to the surface, thus leading to efficient visible-light-responsive photocatalytic oxygen evolution activity from water oxidation.

Ti4+-dopamine/sodium alginate multicomponent complex derived N-doped TiO2@carbon nanocomposites for efficient removal of methylene blue

A one-pot route for the preparation of TiO₂@carbon nanocomposite from Ti⁴⁺/polysaccharide coordination complex has been developed and shown advantages in operation, cost, environment, etc. However, the photodegradation rate of methylene blue needs to be improved. N-doping has been proven as an efficient means to enhance photodegradation performance. Thus, the present study upgraded the TiO₂@carbon nanocomposite to N-doped TiO₂@carbon nanocomposite (N-TiO₂@C) from Ti⁴⁺-dopamine/sodium alginate multicomponent complex. The composites were characterized by FT-IR, XRD, XPS, UV-vis DRS, TG-DTA, and SEM-EDS. TiO₂ was a typical rutile phase, and the carboxyl groups existed on N-TiO₂@C. The photocatalyst consequently showed high removal efficiency of methylene blue (MB). The cycling experiment additionally indicated the high stability of N-TiO₂@C. The present work provided a novel route for preparing N-TiO₂@C. Moreover, it can be extended to prepare N-doped polyvalent metal oxides@carbon composites from all water-soluble polysaccharides such as cellulose derivatives, pectin, starch, and guar gum.

Application of Electrochemical Oxidation for Water and Wastewater Treatment: An Overview

In recent years, the discharge of various emerging pollutants, chemicals, and dyes in water and wastewater has represented one of the prominent human problems. Since water pollution is directly related to human health, highly resistant and emerging compounds in aquatic environments will pose many potential risks to the health of all living beings. Therefore, water pollution is a very acute problem that has constantly increased in recent years with the expansion of various industries. Consequently, choosing efficient and innovative wastewater treatment methods to remove contaminants is crucial. Among advanced oxidation processes, electrochemical oxidation (EO) is the most common and effective method for removing persistent pollutants from municipal and industrial wastewater. However, despite the great progress in using EO to treat real wastewater, there are still many gaps. This is due to the lack of comprehensive information on the operating parameters which affect the process and its operating costs. In this paper, among various scientific articles, the impact of operational parameters on the EO performances, a comparison between different electrochemical reactor configurations, and a report on general mechanisms of electrochemical oxidation of organic pollutants have been reported. Moreover, an evaluation of cost analysis and energy consumption requirements have also been discussed. Finally, the combination process between EO and photocatalysis (PC), called photoelectrocatalysis (PEC), has been discussed and reviewed briefly. This article shows that there is a direct relationship between important operating parameters with the amount of costs and the final removal efficiency of emerging pollutants. Optimal operating conditions can be achieved by paying special attention to reactor design, which can lead to higher efficiency and more efficient treatment. The rapid development of EO for removing emerging pollutants from impacted water and its combination with other green methods can result in more efficient approaches to face the pressing water pollution challenge. PEC proved to be a promising pollutants degradation technology, in which renewable energy sources can be adopted as a primer to perform an environmentally friendly water treatment.

Simultaneous photocatalytic removal of organic dye and heavy metal from textile wastewater over N-doped TiO2 on reduced graphene oxide

Methylene blue (MB) and hexavalent chromium Cr(VI) are hazardous pollutants in textile waste and cannot be completely removed using conventional methods. So far, there have been no specific studies examining the synthesis and activity of N-TiO₂/rGO as a photocatalyst for removing MB and Cr(VI) from textile wastewater. This work especially highlights the synthesis of N-TiO₂/rGO as a photocatalyst which exhibits a wider range of light absorption and is highly effective for simultaneous removal of MB-Cr(VI) under visible light. Titanium tetrachloride (TiCl₄) was used as the precursor for N-TiO₂ synthesis using the sol-gel method. Graphite was oxidized using Hummer's method and reduced with hydrazine to produce rGO. N-TiO₂/rGO was synthesized using a hydrothermal process and then analyzed using several characterization instruments. The X-ray diffraction pattern (XRD) showed that the anatase N-TiO₂/rGO phase was detected at the diffraction peak of 2θ = 25.60°. Scanning electron microscopy and transmission electron microscopy (SEM-EDS and TEM) dispersive X-ray spectrometry images show that N-TiO₂ particles adhere to the surface of rGO with uniform size and N and Ti elements are present in the N-TiO₂/rGO combined investigated. Gas absorption analysis data (GSA) shows that N-TiO₂/rGO had a surface area of 77.449 m²/g, a pore volume of 0.335 cc/g, and a pore size of 8.655 nm. The thermogravimetric differential thermal analysis (TG-DTA) curve showed the anatase phase at 500-780 °C with a weight loss of 0.85%. The N-TiO₂/rGO composite showed a good photocatalyst application. The photocatalytic activity of N-TiO₂/rGO for textile wastewater treatment under visible light showed higher effectiveness than ultraviolet light, with 97.92% for MB and 97.48% for Cr(VI). Combining N-TiO₂ with rGO is proven to increase the light coverage in the visible light region. Removal of MB and Cr(VI) can be carried out simultaneously and results in a removal efficiency of 95.96%.

Nitrogen doped bimetallic sludge biochar composite for synergistic persulfate activation: Reactivity, stability and mechanisms

As a recycling use of waste activated sludge (WAS), we used high-temperature pyrolysis of WAS to support bimetallic Fe-Mn with nitrogen (N) co-doping (FeMn@N-S), a customized composite catalyst that activates peroxysulphate (PS) for the breakdown of tetracycline (TC). First, the performance of TC degradation was evaluated and optimized under different N doping, pH, catalyst dosages, PS dosages, and contaminant concentrations. Activating PS with FeMn@N-S caused the degradation of 91% of the TC in 120 min. Next, characterization of FeMn@N-S by XRD, XPS and FT-IR analysis highlights N doping is beneficial to take shape more active sites and reduces the loss of Fe and Mn during the degradation reaction. As expected, the presence of Fe-Mn bimetallic on the catalyst surface increases the rate of electron transfer, promoting the redox cycle of the catalyst. Other functional groups on the catalyst surface, such as oxygen-containing groups, accelerated the electron transfer during PS activation. Free radical quenching and ESR analysis suggest that the main contributor to TC degradation is surface-bound SO₄^•-, along with the presence of single linear oxygen (¹O₂) oxidation pathway. Finally, the FeMn@N-S composite catalyst exhibits excellent pH suitability and reusability, indicating a solid practicality of this catalyst in PS-based removal of antibiotics from wastewater.

Sulfur Substitution and Defect Engineering in an Unfavored MnMoO4 Catalyst for Efficient Hydrogen Evolution under Visible Light

A novel and nonstoichiometric Mn_1-xMo(S,O)_4-y oxysulfide catalyst with oxygen vacancies and a partial Mo⁶⁺-to-Mo⁴⁺ transition after the substitution of sulfur was synthesized for an efficient photocatalytic hydrogen evolution reaction (PHER). With appropriate sulfur substitution, a MnMoO₄ semiconductor with a wide band gap was converted to Mn_1-xMo(S,O)_4-y with a narrow gap and a suitable band position for PHER. MnMo oxysulfide of 50 mg achieved a high PHER rate of 415.8 μmol/h under visible light, an apparent quantum efficiency (AQE) of 4.31% at 420 nm, and a solar-to-hydrogen (STH) conversion efficiency of 1.28%. Oxygen vacancies (V_O) surrounded by low coordination metal atoms act as active reaction sites, which strengthen water adsorption and activation. Here, we demonstrate that sulfur substitution of MnMoO₄ for lowering its wide band gap can not only disturb the strict periodicity of the lattice but also the valence states of Mn and Mo for enhancing PHER via material design.

Persulfate promoted visible photocatalytic elimination of bisphenol A by g-C3N4-CeO2 S-scheme heterojunction: The dominant role of photo-induced holes

In the last few years, coupling heterogeneous photocatalysis with persulfate (PDS) activation process is an efficient approach to generate abundant reactive oxidative species towards organic contaminant removal in water, however, the key role of PDS in photocatalytic process remains ambiguous. Herein, a novel g-C₃N₄-CeO₂ (CN-CeO₂) step-scheme (S-scheme) composite was constructed to photo-degrade bisphenol A (BPA) with the presence of PDS under visible irradiation. At 2.0 mM PDS, 0.7 g/L CN-CeO₂ and natural pH 6.2, 94.2% of BPA could be eliminated in 60 min under visible light (Vis) illumination. Aside from the previous view of free radical generation, it tends to assume that most of PDS molecules acted as electron sacrificial agents for capturing photo-induced e^- to form sulfate ions, greatly improving the charge carrier separation and thus enhancing the oxidation capacity of nonradical hole (h⁺) for the removal of BPA. Good correlations are further found between the rate constant and descriptor variables (i.e., Hammett constant σ^-/σ⁺ and half-wave potential E_1/2), exhibiting selective oxidation for organic pollutants in the Vis/CN-CeO₂/PDS system. The study brings more insights into mechanistic understanding of persulfate-enhanced photocatalytic process for addressing water decontamination.

Efficient Photodegradation of Rhodamine B by Fiber-like Nitrogen-Doped TiO2/Ni(OH)2 Nanocomposite under Visible Light Irradiation

N-TiO₂/Ni(OH)₂ nanofiber was successfully prepared by combining the electrospinning and solvothermal method. It has been found that under visible light irradiation, the as-obtained nanofiber exhibits excellent activity for the photodegradation of rhodamine B, and the average degradation rate reaches 3.1%/min^-1. Further insight investigations reveal that such a high activity was mainly due to the heterostructure-induced increase in the charge transfer rate and separation efficiency.

Topologically Porous Heterostructures for Photo/Photothermal Catalysis of Clean Energy Conversion

As a straightforward way to fix solar energy, photo/photothermal catalysis with semiconductor provides a promising way to settle the energy shortage and environmental crisis in many fields, especially in clean energy conversion. Topologically porous heterostructures (TPHs), featured with well-defined pores and mainly composed by the derivatives of some precursors with specific morphology, are a major part of hierarchical materials in photo/photothermal catalysis and provide a versatile platform to construct efficient photocatalysts for their enhanced light absorption, accelerated charges transfer, improved stability, and promoted mass transportation. Therefore, a comprehensive and timely review on the advantages and recent applications of the TPHs is of great importance to forecast the potential applications and research trend in the future. This review initially demonstrates the advantages of TPHs in photo/photothermal catalysis. Then the universal classifications and design strategies of TPHs are emphasized. Besides, the applications and mechanisms of photo/photothermal catalysis in hydrogen evolution from water splitting and CO_x hydrogenation over TPHs are carefully reviewed and highlighted. Finally, the challenges and perspectives of TPHs in photo/photothermal catalysis are also critically discussed.

Inactivation of SARS-CoV-2 variants by nitrogen-doped titanium dioxide loaded with metals as visible-light photocatalysts

PURPOSE

We examined the inactivation of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) by a nitrogen-doped titanium dioxide (N-TiO2) visible-light photocatalyst that was activated via light irradiation in the natural environment and was safe for human use as a coating material.

METHODS

The photocatalytic activity of glass slides coated with three types of N-TiO2 without metal or loaded with copper or silver and copper was investigated by measuring acetaldehyde degradation. The titer levels of infectious SARS-CoV-2 were measured using cell culture after exposing photocatalytically active coated glass slides to visible light for up to 60 min.

RESULTS

N-TiO2 photoirradiation inactivated the SARS-CoV-2 Wuhan strain and this effect was enhanced by copper loading and further by the addition of silver. Hence, visible-light irradiation using silver and copper-loaded N-TiO2 inactivated the Delta, Omicron, and Wuhan strains.

CONCLUSION

N-TiO2 could be used to inactivate SARS-CoV-2 variants, including emerging variants, in the environment.

Kinetic Aspects of Benzene Degradation over TiO2-N and Composite Fe/Bi2WO6/TiO2-N Photocatalysts under Irradiation with Visible Light

In this study, composite materials based on nanocrystalline anatase TiO2 doped with nitrogen and bismuth tungstate are synthesized using a hydrothermal method. All samples are tested in the oxidation of volatile organic compounds under visible light to find the correlations between their physicochemical characteristics and photocatalytic activity. The kinetic aspects are studied both in batch and continuous-flow reactors, using ethanol and benzene as test compounds. The Bi2WO6/TiO2-N heterostructure enhanced with Fe species efficiently utilizes visible light in the blue region and exhibits much higher activity in the degradation of ethanol vapor than pristine TiO2-N. However, an increased activity of Fe/Bi2WO6/TiO2-N can have an adverse effect in the degradation of benzene vapor. A temporary deactivation of the photocatalyst can occur at a high concentration of benzene due to the fast accumulation of non-volatile intermediates on its surface. The formed intermediates suppress the adsorption of the initial benzene and substantially increase the time required for its complete removal from the gas phase. An increase in temperature up to 140 °C makes it possible to increase the rate of the overall oxidation process, and the use of the Fe/Bi2WO6/TiO2-N composite improves the selectivity of oxidation compared to pristine TiO2-N.

Formation Mechanism and Bandgap Reduction of GaN-ZnO Solid-Solution Thin Films Fabricated by Nanolamination of Atomic Layer Deposition

Nanolamination of GaN and ZnO layers by atomic layer deposition (ALD) is employed to fabricate GaN-ZnO homogenous solid-solution thin films because it offers more precise control of the stoichiometry. By varying the ALD cycle ratios of GaN:ZnO from 5:10 to 10:5, the (GaN)_{1- x} (ZnO)_x films with 0.39 ≦ x ≦ 0.79 are obtained. The formation of solid solution is explained based on the atomic stacking and preferred orientation of the layers of GaN and ZnO. However, the growth rates of GaN and ZnO during the lamination process are different from those of pure GaN and ZnO films. It is found that GaN grows faster on ZnO, whereas ZnO grows slower on GaN. The density functional theory (DFT) calculations are performed using a superlattice model for GaN and ZnO laminated layers fabricated by ALD to understand the difference of density of states (DOS) and evaluate the bandgaps for various atomic configurations in the solid-solution films. The band positions are experimentally defined by ultraviolet photoelectron spectroscopy. Significant bandgap reduction of the solid solutions is observed, which can be explained by the DOS from the DFT calculations. Visible-light-driven photocatalytic hydrogen evolution is conducted to confirm the applicability of the solid-solution films.

Lychee-like TiO2@Fe2O3 Core-Shell Nanostructures with Improved Lithium Storage Properties as Anode Materials for Lithium-Ion Batteries

In this study, lychee-like TiO₂@Fe₂O₃ microspheres with a core-shell structure have been prepared by coating Fe₂O₃ on the surface of TiO₂ mesoporous microspheres using the homogeneous precipitation method. The structural and micromorphological characterization of TiO₂@Fe₂O₃ microspheres has been carried out using XRD, FE-SEM, and Raman, and the results show that hematite Fe₂O₃ particles (7.05% of the total mass) are uniformly coated on the surface of anatase TiO₂ microspheres, and the specific surface area of this material is 14.72 m² g^-1. The electrochemical performance test results show that after 200 cycles at 0.2 C current density, the specific capacity of TiO₂@Fe₂O₃ anode material increases by 219.3% compared with anatase TiO₂, reaching 591.5 mAh g^-1; after 500 cycles at 2 C current density, the discharge specific capacity of TiO₂@Fe₂O₃ reaches 273.1 mAh g^-1, and its discharge specific capacity, cycle stability, and multiplicity performance are superior to those of commercial graphite. In comparison with anatase TiO₂ and hematite Fe₂O₃, TiO₂@Fe₂O₃ has higher conductivity and lithium-ion diffusion rate, thereby enhancing its rate performance. The electron density of states (DOS) of TiO₂@Fe₂O₃ shows its metallic nature by DFT calculations, revealing the essential reason for the high electronic conductivity of TiO₂@Fe₂O₃. This study presents a novel strategy for identifying suitable anode materials for commercial lithium-ion batteries.

Iron oxide/hydroxide-nitrogen doped graphene-like visible-light active photocatalytic layers for antibiotics removal from wastewater

Hybrid layers consisting of Fe oxide, Fe hydroxide, and nitrogen doped graphene-like platelets have been synthesized by an eco-friendly laser-based method for photocatalytic applications. The complex composite layers show high photodecomposition efficiency towards degradation of antibiotic molecules under visible light irradiation. The photodecomposition efficiency was investigated as a function of relative concentrations of base materials, Fe oxide nanoparticles and graphene oxide platelets used for the preparation of target dispersions submitted to laser irradiation. Although reference pure Fe oxide/Fe hydroxide layers have high absorption in the visible spectral region, their photodecomposition efficiency is negligible under the same irradiation conditions. The high photocatalytic decomposition efficiency of the nanohybrid layer, up to 80% of the initial antibiotic molecules was assigned to synergistic effects between the constituent materials, efficient separation of the electron-hole pairs generated by visible light irradiation on the surface of Fe oxide and Fe hydroxide nanoparticles, in the presence of conducting graphene-like platelets. Nitrogen doped graphene-like platelets contribute also to the generation of electron-hole pairs under visible light irradiation, as demonstrated by the photocatalytic activity of pure, reference nitrogen doped graphene-like layers. The results also showed that adsorption processes do not contribute significantly to the removal of antibiotic molecules from the test solutions. The decrease of the antibiotic concentration under visible light irradiation was assigned primarily to photocatalytic decomposition mechanisms.

Doped and immobilized titanium dioxide photocatalysts as a potential source of nitrosamine formation

Immobilized and visible-light-active titanium dioxide (TiO₂) is widely used for water treatment. However, the accelerated generation of degradation byproducts is a potential risk of TiO₂-based photocatalysis. This study aimed to investigate the structural effect of engineered TiO₂ samples on the formation of major nitrosamines during photocatalysis. The nitrogen-containing impurities and leached metal ions from doped-TiO₂ samples could exacerbate nitrosamine formation potential (FP) in distilled water, secondary effluent, and chloraminated water. Doped-TiO₂ with 2-ethylimidazole, trimethylamine, triethylamine, and N-carbon nanotubes could leach in the range of 47-64 ng L^-1 nitrosamines (including N-nitrosomethylethylamine, N-nitrosodiethylamine, N-nitrosodimethylamine, and N-nitrosopyrrolidine) even under dark conditions. Furthermore, we investigated the role of metal dopants on nitrosamine-FP during the chloramination of precursors such as dimethylamine and microcystin-LR. Metal ions such as Cu that leached from the metal-doped catalysts may catalyze the nitrosamine-FP. Therefore, pre-purification (washing) and immobilization of doped-TiO₂ samples on substrates are suggested to remove a considerable amount of nitrosamines. However, during the prolonged tryout, the selection of substrates was critical. Polymeric supports, such as polyimide and polyvinylpyrrolidone, can produce up to 85 ng L^-1 nitrosamine, whereas TiO₂ immobilized onto steel mesh can remove nitrosamine formation during photocatalytic oxidation followed by chloramination. This study systematically screened a diverse range of dopants, supports, and solvents in engineered TiO₂ photocatalysts, in 61 samples, and provided novel insights into their effect on nitrosamine formation.

Construction of a novel Cu1.8S/NH2-La MOFs decorated Black-TNTs photoanode electrode for high-efficiently photoelectrocatalytic degradation of 2, 4-dichlorophenol

Photoelectrocatalysis (PEC) has long been regarded as an efficient and green method to eliminate various organic pollutants from wastewater. However, the lack of highly photoelectrocatalytic active and stable electrodes limits the development of the PEC technologies. Herein, a novel hierarchical photo-electrode with hollow Cu_1.8S/NH₂-La MOFs decorated black titanium dioxide nanotubes (Cu_1.8S/NH₂-La MOFs/Black TNTs) was fabricated by a two-step water-heating method. The prepared photoelectrode was used to degradation of 2, 4-dichlorophenol (2, 4-DCP). Analysis of photoelectrocatalytic degradation process of 2, 4-DCP was evaluated using UV-Vis absorption spectroscopy and the main degradation paths were analyzed by LC-MS. The results showed that 99.3% of the pollutant could be rapidly degraded within 180 min. Furthermore, the Cu_1.8S/NH₂-La MOFs/Black TNTs photoelectric pole exhibited excellent stability after 15 cycling experiments.

Recent Advances in Black TiO2 Nanomaterials for Solar Energy Conversion

Titanium dioxide (TiO₂) nanomaterials have been widely used in photocatalytic energy conversion and environmental remediation due to their advantages of low cost, chemical stability, and relatively high photo-activity. However, applications of TiO₂ have been restricted in the ultraviolet range because of the wide band gap. Broadening the light absorption of TiO₂ nanomaterials is an efficient way to improve the photocatalytic activity. Thus, black TiO₂ with extended light response range in the visible light and even near infrared light has been extensively exploited as efficient photocatalysts in the last decade. This review represents an attempt to conclude the recent developments in black TiO₂ nanomaterials synthesized by modified treatment, which presented different structure, morphological features, reduced band gap, and enhanced solar energy harvesting efficiency. Special emphasis has been given to the newly developed synthetic methods, porous black TiO₂, and the approaches for further improving the photocatalytic activity of black TiO₂. Various black TiO₂, doped black TiO₂, metal-loaded black TiO₂ and black TiO₂ heterojunction photocatalysts, and their photocatalytic applications and mechanisms in the field of energy and environment are summarized in this review, to provide useful insights and new ideas in the related field.

Fabrication of bio-inspired metal-based superhydrophilic and underwater superoleophobic porous materials by hydrothermal treatment and magnetron sputtering

Oil-water separation using porous superhydrophilic materials is a promising method to circumvent the issue of oil-polluted water by separating water from oil-water mixtures. However, fabricating metal-based porous superhydrophilic materials with stable superhydrophilicity that can recover their strong hydrophilicity and have acceptable oil-water separation efficiency without complex external stimuli is still a challenge. Inspired by the anti-wetting behavior of broccoli buds, this study successfully fabricated metal-based superhydrophilic and underwater superoleophobic porous materials by hydrothermal treatment of stainless steel meshes (SSMs) combined with magnetron sputtering of metallic Ti and W. The process was then followed with annealing at 300 °C for 4 hours. The effects of coating materials, annealing temperature, and surface structure on the wetting behavior of the prepared meshes were studied and analyzed. The modified meshes exhibited unique broccoli-like microstructures coated with thin TiO_2-x N _x /WO₃ films and showed superhydrophilicity with a 0° water contact angle (WCA) and underwater superoleophobicity with underwater oil contact angles (UOCAs) higher than 155°. They also maintained strong hydrophilicity for more than three weeks with WCAs of less than 13°. Besides, they could recover their initial superhydrophilicity with a 0° WCA after post-annealing at 80 °C for 30 minutes. Notably, the broccoli-like structures and the strong hydrophilic coatings contributed to a significant water flow rate (Q) of 3650 L m^-2 h^-1 and satisfactory oil-water separation efficiency of 98% for more than 15 separation cycles toward various oil-water mixtures. We believe that the presented method and fabricated material are promising and can be applied to induce hydrophilicity of various metallic materials for practical applications of oil-water separation, anti-fouling, microfluidic transport, and water harvesting.

Immobilization of photocatalytic materials for (waste)water treatment using 3D printing technology - advances and challenges

Photocatalysis has been considered a promising technology for the elimination of a wide range of pollutants in water. Various types of photocatalysts (i.e., homojunction, heterojunction, dual Z-scheme photocatalyst) have been developed in recent years to address the drawbacks of conventional photocatalysts, such as the large energy band gap and rapid recombination rate of photogenerated electrons and holes. However, there are still challenges in the design of photocatalytic reactors that limit their wider application for real (waste)water treatment, such as difficulties in their recovery and reuse from treated (waste)waters. 3D printing technologies have been introduced very recently for the immobilization of materials in novel photocatalytic reactor designs. The present review aims to summarize and discuss the advances and challenges in the application of various 3D printing technologies (i.e., stereolithography, inkjet printing, and direct ink writing) for the fabrication of stable photocatalytic materials for (waste)water treatment purposes. Furthermore, the limitations in the implementation of these technologies to design future generations of photocatalytic reactors have been critically discussed, and recommendations for future studies have been presented.

Recent Advances in Ternary Metal Oxides Modified by N Atom for Photocatalysis

Ternary metal oxides (TMOs) with flexible band structures are of significant potential in the field of photocatalysis. The efficient utilization of renewable and green solar energy is of great importance to developing photocatalysts. To date, a wide range of TMOs systems has been developed as photocatalysts for water and air purification, but their practical applications in visible light-assisted chemical reactions are hindered mainly by its poor visible light absorption capacity. Introduction of N atoms into TMOs can narrow the band-gap energy to a lower value, enhance the absorption of visible light and suppress the recombination rate of photogenerated electrons and holes, thus improving the photocatalytic performance. This review summarizes the recent research on N-modified TMOs, including the influence of N doping amounts, N doping sites, and N-induced phase transformation. The introduced N greatly tuned the optical properties, electronic structure, and photocatalytic activity of the TMOs. The optimal N concentration and the influence of N doping sites are investigated. The substitutional N and interstitial N contributed differently to the band gap and electron transport. The introduced N can tune the vacancies in TMOs due to the charge compensation, which is vital for inducing different activity and selectivity. The topochemical ammonolysis process can convert TMOs to oxynitride with visible light absorption. By altering the band structures, these oxynitride materials showed enhanced photocatalytic activity. This review provides an overview of recent advances in N-doped TMOs and oxynitrides derived from TMOs as photocatalysts for environmental applications, as well as some relevant pointers for future burgeoning research development.

A critical review on biochar-based catalysts for the abatement of toxic pollutants from water via advanced oxidation processes (AOPs)

Proper waste disposal is a key towards sustainable development. Wastewater treatment is delineated by the application of efficient, economic and novel catalysts. Biochar is derived from the thermochemical conversion of biomass or any carbonaceous materials and is considered as one of the most eco-friendly substitute for activated carbon. Owing to its large surface area, porosity, crystallinity and active functional groups, the biochar-based catalysts has been extensively applied for the abatement of toxic pollutants from wastewater streams. While most of the reviews focus on the adsorptive properties of the biochar, this review critically analyses the recent development of biochar-based catalysts in the field of advanced oxidation processes (Fenton-like systems, photocatalytic and sonocatalytic systems). The presence of persistent free radicals and oxygen-containing functional groups renders biochar to act as catalyst. The mechanisms accompanying catalytic performance of biochar-based catalysts have also been reviewed. However, the research in this area is quite at an initial phase, and many advancements schemes are essential prior to scale-up and commercialization. Future researches should be devoted to more efficient and rigorous understanding of the structural properties of biochar to engineer the catalytic degradation of targeted pollutants in wastewater treatment.

Nitrogen-Doped Titanium Dioxide as a Hole Transport Layer for High-Efficiency Formamidinium Perovskite Solar Cells

Perovskite solar cells (PSCs) offer advantages over widely deployed silicon solar cells in terms of ease of fabrication; however, the device is still under rigorous materials optimization for cell performance, stability, and cost. In this work, we explore a version of a PSC by replacing the polymeric hole transport layer (HTL) such as Spiro-OMeTAD, P3HT, and PEDOT: PSS with a more air-stable metal oxide, viz., nitrogen-doped titanium dioxide (TiO₂:N). Numerical simulations on formamidinium (FA)-based PSCs in the FTO/TiO₂/FAPbI₃/Ag configuration have been carried out to depict the behaviour of the HTL as well as the effect of absorber layer thickness (∆t) on photovoltaic parameters. The results show that the cell output increases when the HTL bandgap increases from 2.5 to 3.0 eV. By optimizing the absorber layer thickness and the gradient in defect density (Nt), the device structure considered here can deliver a maximum power conversion efficiency of ~21.38% for a lower HTL bandgap (~2.5 eV) and ~26.99% for a higher HTL bandgap of ~3.0 eV. The results are validated by reproducing the performance of PSCs employing commonly used polymeric HTLs, viz. Spiro-OMeTAD, P3HT, and PEDOT: PSS as well as high power conversion efficiency in the highly crystalline perovskite layer. Therefore, the present study provides high-performing, cost-effective PSCs using TiO₂:N.

Rapid Microwave-Assisted Synthesis of N/TiO2/rGO Nanoparticles for the Photocatalytic Degradation of Pharmaceuticals

Nanocomposites comprising nitrogen-doped TiO₂ and reduced graphene oxide (N/TiO₂/rGO), with different rGO loading qualities, were prepared by a cost-effective microwave-assisted synthesis method. The synthesized materials were broadly characterized by Raman spectroscopy, X-ray diffraction (XRD), infrared spectroscopy (FTIR), photoelectron spectroscopy (XPS), diffuse reflectance spectroscopy (DRS), electron microscopy (SEM-EDS), and nitrogen adsorption/desorption isotherms. Anatase was the only crystalline phase observed for all synthesized materials. The rGO loading did not affect the morphological properties, but it positively influenced the photocatalytic activity of the nanocomposite materials, especially at low rGO loading. Photocatalysts were evaluated via the degradation of specific organic micropollutant (OMP) pharmaceuticals: ciprofloxacin (CIP), diclofenac (DCF), and salicylic acid (SA), under different radiation sources: ultraviolet A (UVA), solar light simulator (SLS), blue visible light (BVL) and cold visible light (CVL). CIP and SA were removed effectively via the synergy of adsorption and photocatalysis, while DCF degradation was achieved solely by photocatalysis. After implementing scavenger agents, photocatalytic degradation processes mainly depended on the specific pollutant type, while irradiation sources barely defined the photocatalytic mechanism. On the other hand, changes in irradiation intensity significantly influenced the photolysis process, while photocatalysis was slightly affected, indicating that irradiation spectra are more relevant than intensity.

In situself-assembly fabrication of ultrathin sheet-like CuS modified g-C3N4heterojunction and its enhanced visible-light photocatalytic performance

Photocatalysts with heterojunction structure have been widely used for organic degradation. In this study, CuS/g-C₃N₄heterojunction was formed byin situself-assembly via a simply hydrothermal method. A series of characterizations were applied to analyzing the morphology, structure, optical properties and photo-induced electron transfer of the samples. The effect of CuS mass ratio in the CuS/g-C₃N₄composite on methyl blue (10 mg l^-1) degradation under visible-light illumination was discussed. When CuS mass ratio was 60%, CuS/g-C₃N₄behaved the highest photocatalytic efficiency which is 17 times higher than that of pure g-C₃N₄, and the optimal heterojunction exhibited promising photocatalytic stability as well. The synthesized CuS/g-C₃N₄with intimate contact and promising photocatalytic performance provides important implications on analogous researches on g-C₃N₄-based heterojunctions for photocatalytic applications.