Efficient photocatalytic decomposition of perfluorooctanoic acid by indium oxide and its mechanism

Efficient photodegradation of perfluoroalkyl substances under visible light by hexagonal ZnIn2S4 nanosheets

Perfluoroalkyl substances (PFASs) are typical persistent organic pollutants, and their removal is urgently required but challenging. Photocatalysis has shown potential in PFASs degradation due to the redox capabilities of photoinduced charge carriers in photocatalysts. Herein, hexagonal ZnIn2S4 (ZIS) nanosheets were synthesized by a one-pot oil bath method and were well characterized by a series of techniques. In the degradation of sodium p-perfluorous nonenoxybenzenesulfonate (OBS), one kind of representative PFASs, the as-synthesized ZIS showed activity superior to P25 TiO2 under both simulated sunlight and visible-light irradiation. The good photocatalytic performance was attributed to the enhanced light absorption and facilitated charge separation. The pH conditions were found crucial in the photocatalytic process by influencing the OBS adsorption on the ZIS surface. Photogenerated e- and h+ were the main active species involved in OBS degradation in the ZIS system. This work confirmed the feasibility and could provide mechanistic insights into the degradation and defluorination of PFASs by visible-light photocatalysis.

Efficient photocatalytic decomposition of PFOA over BiOI1-x with low power LED light

In recent years, the academic community has shown significant interest in per- or polyfluoroalkyl compounds (PFAS) due to their challenging degradation and potential health risks. Photocatalysis has been investigated for PFAS decomposition due to its environmentally friendly nature. In this study, BiOI with abundant iodine vacancies was synthesized through solvothermal and calcination methods (referred to as BiOI1-x), and was used for PFAS degradation with a low power UV light source. Compared to pure BiOI, BIOI1-x showed higher photocatalytic activity towards PFOA (perfluorooctanoic acid). Within 5 h under 5 W LED light irradiation, the degradation rate of PFOA reached 51.9 % with BiOI1-x calcined at 440 °C (No significant degradation of PFAS was observed with pure BiOI). Capture experiments, electron paramagnetic resonance spectroscopy, and electrochemical experiments revealed that the main active species in the system were photogenerated holes, followed by hydroxyl radicals. Furthermore, the presence of iodine vacancies significantly improved the efficiency of charge carrier separation and enhanced the photocatalytic performance. Finally, a hypothetical degradation pathway for PFOA in this system was suggested. This study achieved efficient degradation of PFAS under low power LED light (5 W), emphasizing its significant practical importance in terms of energy conservation.

Innovative techniques for combating a common enemy forever chemicals: A comprehensive approach to mitigating per- and polyfluoroalkyl substances (PFAS) contamination

The pervasive presence of per and polyfluoroalkyl substances (PFAS), commonly referred to as "forever chemicals," in water systems poses a significant threat to both the environment and public health. PFAS are persistent organic pollutants that are incredibly resistant to degradation and have a tendency to accumulate in the environment, resulting in long-term contamination issues. This comprehensive review delves into the primary impacts of PFAS on both the environment and human health while also delving into advanced techniques aimed at addressing these concerns. The focus is on exploring the efficacy, practicality, and sustainability of these methods. The review outlines several key methods, such as advanced oxidation processes, novel materials adsorption, bioremediation, membrane filtration, and in-situ chemical oxidation, and evaluates their effectiveness in addressing PFAS contamination. By conducting a comparative analysis of these techniques, the study aims to provide a thorough understanding of current PFAS remediation technologies, as well as offer insights into integrated approaches for managing these persistent pollutants effectively. While acknowledging the high efficiency of adsorption and membrane filtration in reducing persistent organic pollutants due to their relatively low cost, versatility, and wide applicability, the review suggests that the integration of these methods could result in an overall enhancement of removal performance. Additionally, the study emphasizes the need for researcher attention in key areas and underscores the necessity of collaboration between researchers, industry, and regulatory authorities to address this complex challenge.

Efficient Removal of PFASs Using Photocatalysis, Membrane Separation and Photocatalytic Membrane Reactors

Perfluoroalkyl and polyfluoroalkyl substances (PFASs) are persistent compounds characterized by stable C-F bonds giving them high thermal and chemical stability. Numerous studies have highlighted the presence of PFASs in the environment, surface waters and animals and humans. Exposure to these chemicals has been found to cause various health effects and has necessitated the need to develop methods to remove them from the environment. To date, the use of photocatalytic degradation and membrane separation to remove PFASs from water has been widely studied; however, these methods have drawbacks hindering them from being applied at full scale, including the recovery of the photocatalyst, uneven light distribution and membrane fouling. Therefore, to overcome some of these challenges, there has been research involving the coupling of photocatalysis and membrane separation to form photocatalytic membrane reactors which facilitate in the recovery of the photocatalyst, ensuring even light distribution and mitigating fouling. This review not only highlights recent advancements in the removal of PFASs using photocatalysis and membrane separation but also provides comprehensive information on the integration of photocatalysis and membrane separation to form photocatalytic membrane reactors. It emphasizes the performance of immobilized and slurry systems in PFAS removal while also addressing the associated challenges and offering recommendations for improvement. Factors influencing the performance of these methods will be comprehensively discussed, as well as the nanomaterials used for each technology. Additionally, knowledge gaps regarding the removal of PFASs using integrated photocatalytic membrane systems will be addressed, along with a comprehensive discussion on how these technologies can be applied in real-world applications.

A review on the advancement in photocatalytic degradation of poly/perfluoroalkyl substances in water: Insights into the mechanisms and structure-function relationship

Poly/perfluoroalkyl substances (PFAS) are persistent organic pollutants and ubiquitous in aquatic environment, which are hazardous to organisms and human health. Several countries and regions have taken actions to regulate or limit the production and emission of some PFAS. Even though a series of water treatment technologies have been developed for removal of PFAS to eliminate their potential adverse effects, the removal and degradation performance are usually unsatisfactory. Photocatalytic degradation of PFAS is considered as one of the most effective approaches due to the mild operation conditions and environmental friendliness. This review systematically summarized the recent advances in photocatalytic degradation of PFAS based on heterogeneous photocatalysts, including TiO2-, Ga2O3-, In2O3-, ZnO-, Bi-based, and others. Overall, two mainly degradation mechanisms were involved, including photo-oxidation (involving the holes and oxidative radicals) and photo-reduction types (by e- and reductive radicals). The band structures of the photocatalysts, degradation pathways, structure-function relationship, and impacting factors were further discussed to elucidate the essential reasons for the enhanced degradation of PFAS. Furthermore, the review identified the major knowledge gaps to solve the issues of photocatalysis in real application. This paper also propounded several strategies to promote the design and optimization of high-efficient photocatalysts, and meet the challenges to remove PFAS through photodegradation technologies.

PFOA-contaminated soil remediation: a comprehensive review

Soil and groundwater contamination has been raised as a concern due to the capability of posing a risk to human health and ecology, especially in facing highly toxic and emerging pollutants. Because of the prevalent usage of perfluorooctanoic acid (PFOA), in industrial and production processes, and subsequently the extent of sites contaminated with these pollutants, cleaning up PFOA polluted sites is paramount. This research provides a review of remediation approaches that have been used, and nine remediation techniques were reviewed under physical, chemical, and biological approaches categorization. As the pollutant specifications, environmental implications, and adverse ecological effects of remediation procedures should be considered in the analysis and evaluation of remediation approaches, unlike previous research that considered a couple of PFAS pollutants and generally dealt with technical issues, in this study, the benefits, drawbacks, and possible environmental and ecological adverse effects of PFOA-contaminated site remediation also were discussed. In the end, in addition to providing sufficient and applicable understanding by comprehensively considering all aspects and field-scale challenges and obstacles, knowledge gaps have been found and discussed.

Mechanisms for synergistically enhancing cadmium remediation performance of biochar: Silicon activation and functional group effects

This work proposes an advanced biochar material (β-CD@SiBC) for controllable transformation of specific silicon (Si) forms through endogenous Si activation and functional group introduction for efficient cadmium (Cd) immobilization and removal. The maximum adsorption capacity of β-CD@SiBC for Cd(II) reached 137.6 mg g-1 with a remarkable removal efficiency of 99 % for 200 mg L-1Cd(II). Moreover, the developed β-CD@SiBC flow column exhibited excellent performance at the environmental Cd concentration, with the final concentration meeting the environmental standard for surface water quality (0.05 mg L-1). The remediation mechanism of β-CD@SiBC could be mainly attributed to mineral precipitation and ion exchange, which accounted for 42 % and 29 % of the remediation effect, respectively, while functional group introduction enhanced its binding stability with Cd. Overall, this work proposes the role and principle of transformation of Si forms within biochar, providing new strategies for better utilizing endogenous components in biomass.

Analysis of perfluorinated compounds in sewage sludge and hydrochar by UHPLC LTQ/Orbitrap MS and removal assessment during hydrothermal carbonization treatment

Wastewater treatment plants have been recognized as important sinks for per- and polyfluoroalkyl substances (PFAS) because of their ineffectiveness in removing them reflecting both water and sewage sludge discharge routes. Hydrothermal treatment represents an alternative technology for treating sludge to recover energy and other valuable products. In this study, 15 PFAS were determined in sludge and hydrochar substrates using sonication-solid phase extraction procedure and analyzed using LC-Orbitrap-High Resolution-MS/MS. The method was fully validated, exhibiting very good linearity, recoveries in the range of 48 to 126 %, low detection and quantification limits with expanded uncertainty and precision below 32 % and 21.9 %, respectively. The method was applied to sludge samples from the WWTP of Ioannina city (Greece), as well as to hydrothermally treated samples under various conditions. The most abundant PFAS were PFHxA (0.5-38.3 ng g-1) and PFOS (4.4-22.1 ng g-1). Finally, the hydrothermally treated sludge samples spiked with PFAS presented removal efficiencies for total PFAS of 86.9 %, 91.8 % and 95.7 % at three spiking levels namely 10, 50 and 200 ng g-1, respectively. Results indicated that PFCAs were almost completely removed, except for PFOA, while the concentrations of PFSAs increased in the produced hydrochar with the formation of several intermediates, as detected by HR-LC-MS/MS. The results of this study demonstrate the effect of hydrothermal treatment to the fate of PFAS in sewage sludge and contribute for further studies on design and scale up of hydrothermal carbonization technology as a management option for safer disposal of municipal wastewater sludge.

Progress and perspectives on carbon-based materials for adsorptive removal and photocatalytic degradation of perfluoroalkyl and polyfluoroalkyl substances (PFAS)

Per- and polyfluoroalkyl substances (PFAS) (also known as 'forever chemicals') have emerged as trace pollutants of global concern, attributing to their persistent and bio-accumulative nature, pervasive distribution, and adverse public health and environmental impacts. The unregulated discharge of PFAS into aquatic environments represents a prominent threat to the wellbeing of humans and marine biota, thereby exhorting unprecedented action to tackle PFAS contamination. Indeed, several noteworthy technologies intending to remove PFAS from environmental compartments have been intensively evaluated in recent years. Amongst them, adsorption and photocatalysis demonstrate remarkable ability to eliminate PFAS from different water matrices. In particular, carbon-based materials, because of their diverse structures and many exciting properties, offer bountiful opportunities as both adsorbent and photocatalyst, for the efficient abatement of PFAS. This review, therefore, presents a comprehensive summary of the diverse array of carbonaceous materials, including biochar, activated carbon, carbon nanotubes, and graphene, that can serve as ideal candidates in adsorptive and photocatalytic treatment of PFAS contaminated water. Specifically, the efficacy of carbon-mediated PFAS removal via adsorption and photocatalysis is summarised, together with a cognizance of the factors influencing the treatment efficiency. The review further highlights the neoteric development on the novel innovative approach 'concentrate and degrade' that integrates selective adsorption of trace concentrations of PFAS onto photoactive surface sites, with enhanced catalytic activity. This technique is way more energy efficient than conventional energy-intensive photocatalysis. Finally, the review speculates the cardinal challenges associated with the practical utility of carbon-based materials, including their scalability and economic feasibility, for eliminating exceptionally stable PFAS from water matrices.

Photocatalysts for chemical-free PFOA degradation - What we know and where we go from here?

Perfluorooctanoic acid (PFOA) is a toxic and recalcitrant perfluoroalkyl substance commonly detected in the environment. Its low concentration challenges the development of effective degradation techniques, which demands intensive chemical and energy consumption. The recent stringent health advisories and the upgrowth and advances in photocatalytic technologies claim the need to evaluate and compare the state-of-the-art. Among these systems, chemical-free photocatalysis emerges as a cost-effective and sustainable solution for PFOA degradation and potentially other perfluorinated carboxylic acids. This review (I) classifies the state-of-the-art of chemical-free photocatalysts for PFOA degradation in families of materials (Ti, Fe, In, Ga, Bi, Si, and BN), (II) describes the evolution of catalysts, identifies and discusses the strategies to enhance their performance, (III) proposes a simplified cost evaluation tool for simple techno-economical analysis of the materials; (IV) compares the features of the catalysts expanding the classic degradation focus to other essential parameters, and (V) identifies current research gaps and future research opportunities to enhance the photocatalyst performance. We aim that this critical review will assist researchers and practitioners to develop rational photocatalyst designs and identify research gaps for green and effective PFAS degradation.

Photodegradation and photocatalysis of per- and polyfluoroalkyl substances (PFAS): A review of recent progress

Per- and polyfluoroalkyl substances (PFAS) are oxidatively recalcitrant organic synthetic compounds. PFAS are an exceptional group of chemicals that have significant physical characteristics due to the presence of the most electronegative element (i.e., fluorine). PFAS persist in the environment, bioaccumulate, and have been linked to toxicological impacts. Epidemiological and toxicity studies have shown that PFAS pose environmental and health risks, requiring their complete elimination from the environment. Various separation technologies, including adsorption with activated carbon or ion exchange resin; nanofiltration; reverse osmosis; and destruction methods (e.g., sonolysis, thermally induced reduction, and photocatalytic dissociation) have been evaluated to remove PFAS from drinking water supplies. In this review, we will comprehensively summarize previous reports on the photodegradation of PFAS with a special focus on photocatalysis. Additionally, challenges associated with these approaches along with perspectives on the state-of-the-art approaches will be discussed. Finally, the photocatalytic defluorination mechanism of perfluorooctanoic acid (PFOA) and perfluorooctanesulfonic acid (PFOS) following complete mineralization will also be examined in detail.

Strategies to improve adsorption and photocatalytic performance of metal-organic frameworks (MOFs) for perfluoroalkyl and polyfluoroalkyl substances (PFASs) removal from water: A review

Perfluoroalkyl and polyfluoroalkyl substances (PFASs) represent a category of persistent and hazardous organic pollutants extensively prevalent across aquatic environments. The combination of adsorption and photocatalytic degradation has been identified as an effective approach for removing trace amounts of PFASs from water. Among the various materials explored for this purpose, metal-organic frameworks (MOFs) have structural solid tunability, and suitable modification methods could endow them with rich adsorption capabilities and excellent photocatalytic performance, which has potential for applications involving the treatment of trace, multi-chain-length PFASs in water. The research within this realm is currently in its nascent phase, and a holistic knowledge of modification methods can provide a comprehensive framework for future studies. Therefore, this review intends to (1) summarize the mechanism underlying the adsorption and photocatalytic removal of PFASs by MOFs; (2) present various modification methods aimed at enhancing the adsorption and photocatalytic performance of MOFs in alignment with the goal mentioned above; (3) provide an outlook on the prospects of utilizing MOFs for PFASs removal based on current trends and data. Ultimately, the findings from these studies will contribute to advancing knowledge in this area and facilitate the development of effective strategies for addressing PFASs contamination in water systems.

Molecular Cu Electrocatalyst Escalates Ambient Perfluorooctanoic Acid Degradation

Groundwater reservoirs contaminated with perfluoroalkyl and polyfluoroalkyl substances (PFASs) need purifying remedies. Perfluorooctanoic acid (PFOA) is the most abundant PFAS in drinking water. Although different degradation strategies for PFOA have been explored, none of them disintegrates the PFOA backbone rapidly under mild conditions. Herein, we report a molecular copper electrocatalyst that assists in the degradation of PFOA up to 93% with a 99% defluorination rate within 4 h of cathodic controlled-current electrolysis. The current-normalized pseudo-first-order rate constant has been estimated to be quite high for PFOA decomposition (3.32 L h-1 A-1), indicating its fast degradation at room temperature. Furthermore, comparatively, rapid decarboxylation over the first 2 h of electrolysis has been suggested to be the rate-determining step in PFOA degradation. The related Gibbs free energy of activation has been calculated as 22.6 kcal/mol based on the experimental data. In addition, we did not observe the formation of short-alkyl-chain PFASs as byproducts that are typically found in chain-shortening PFAS degradation routes. Instead, free fluoride (F-), trifluoroacetate (CF3COO-), trifluoromethane (CF3H), and tetrafluoromethane (CF4) were detected as fragmented PFOA products along with the evolution of CO2 using gas chromatography (GC), ion chromatography (IC), and gas chromatography-mass spectrometry (GC-MS) techniques, suggesting comprehensive cleavage of C-C bonds in PFOA. Hence, this study presents an effective method for the rapid degradation of PFOA into small ions/molecules.

Subnanoscale spatially confined heterogeneous Fenton reaction enables mineralization of perfluorooctanoic acid

Superoxide radical (•O2-) is capable of degrading perfluorinated compounds that are persistent in nature and cannot be removed by biological or advanced oxidation treatments, but the inherent drawback is the negligible reactivity of •O2-in aqueous phases due to the hydration effect. Here, we explored an innovative way to make use of •O2- by modulating a partial hydration state through spatial confinement control. We demonstrated this idea by conducting heterogeneous Fenton reaction with layered iron oxychloride (FeOCl) catalyst, wherein •O2-radicals produced and confined within the catalyst structure (interlayer spacing of 7.92 Å) showed defluorination effect dealing with perfluorooctanoic acid (PFOA) as model compound. The defluorination combined with advanced oxidation achieved mineralization. Mechanism study revealed that the confinement frustrated the hydration shell of •O2-with coordination number reduced from 3.3 (for bulk phase) to 1.89, and thereby changed its orbital electron properties and enhanced the nucleophilic ability. We further demonstrated a compact FeOCl membrane reactor with highly efficient degradation of PFOA (kobs up to 1.2 min-1) and cost-effective mineralization (2 × 10-6 $ per mgC), operated under ultrafiltration reaction mode. Our findings highlight the great interest of developing spatial confinement technology to modulate •O2--based reactions, as well as the feasibility of combining confinement catalyst structures with heterogeneous Fenton reaction to achieve the mineralization treatment goal.

Semiconductor-hydrophobic material interfaces as a new active site paradigm for photocatalytic degradation of perfluorocarboxylic acids

Photocatalytic degradation of long-chain perfluorocarboxylic acid (PFCA) water contaminants has been reported for numerous of semiconductors, including composite TiO₂ particles decorated with graphitic carbon co-catalysts. While pristine TiO₂ degrades PFCAs inefficiently, the carbon components purportedly enhance activity due to their conductive nature and resultant charge separation enhancement. Yet herein, we present evidence that the catalytic activity of a graphene oxide (GO)-TiO₂ composite from the literature arose not due to from charge separation, but to a unique mode of PFCA adsorption occurring at the interface of TiO₂ and hydrophobic GO. Photocatalytic degradation rates by GO-TiO₂ were compared to those of composites containing nonconductive polymer microparticles (polyethylene, polytetrafluoroethylene). Results showed that polymer-TiO₂ composites performed as well as GO-TiO₂ in degrading both perfluorooctanoic acid and oxalate, a common hole scavenger. Thus, the enhanced activity may occur for any TiO₂-hydrophobic interface, regardless of co-catalyst conductivity. Furthermore, compared to an unmodified reference catalyst, chain length dependence of PFCA degradation by a polymer-TiO₂ composite was found to be less severe, with greater activity toward short-chain species indicating enhanced adsorption behavior. Potential adsorption mechanisms are presented, along with broader implications toward improving the applicability of heterogeneous processes toward a wider range of perfluoroalkyl contaminants.

Research Updates on the Mechanism and Influencing Factors of the Photocatalytic Degradation of Perfluorooctanoic Acid (PFOA) in Water Environments

Perfluorooctanoic acid is ubiquitous in water bodies and is detrimental to the health of organisms. Effectively removing perfluorooctanoic acid (PFOA), a persistent organic pollutant, has been a hot topic around the world. With traditional physical, chemical, and biological methods, it is difficult to effectively and completely remove PFOA, the costs are high, and it is easy to cause secondary pollution. There are difficulties in applying some technologies. Therefore, more efficient and green degradation technologies have been sought. Photochemical degradation has been shown to be a low-cost, efficient, and sustainable technique for PFOA removal from water. Photocatalytic degradation technology offers great potential and prospects for the efficient degradation of PFOA. Most studies on PFOA have been conducted under ideal laboratory conditions at concentrations that are higher than those detected in real wastewater. This paper summarizes the research status of the photo-oxidative degradation of PFOA, and it summarizes the mechanism and kinetics of PFOA degradation in different systems, as well as the influence of key factors on the photo-oxidative degradation and defluoridation process, such as system pH, photocatalyst concentration, etc. PFOA photodegradation technology's existing problems and future work directions are also presented. This review provides a useful reference for future research on PFOA pollution control technology.

Synthesis of Petitjeanite Bi3O(OH)(PO4)2 Photocatalytic Microparticles: Effect of Synthetic Conditions on the Crystal Structure and Activity toward Degradation of Aqueous Perfluorooctanoic Acid (PFOA)

The discovery of synthetic Bi₃O(OH)(PO₄)₂ [BOHP] and its application toward photocatalytic oxidation of the water contaminant perfluorooctanoic acid (PFOA) have prompted further interest in development. Despite its high activity toward PFOA degradation, the scarce appearance in the literature and lack of research have left a knowledge gap in the understanding of BOHP synthesis, formation, and photocatalytic activity. Herein, we explore the crystallization of BOHP microparticles via hydrothermal syntheses, focusing on the influence of ions and organics present in the reaction solution when using different hydroxide amendments (NaOH, NH₄OH, NMe₄OH, and NEt₄OH). To better understand the unique structure-activity aspects of BOHP, the related bismuth oxy phosphate (BOP) structural family was also explored, including A-BOP (A = Na⁺ and K⁺) and M-BOP derivatives (M = Ca²⁺, Sr²⁺, and Pb²⁺). Results from materials characterization, including X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray spectroscopy, indicated that the crystal structure, morphology, and atomic composition were significantly influenced by solution pH, inorganic metal cations (Na⁺, K⁺, Ca²⁺, Sr²⁺, and Pb²⁺), and organic amines. Experiments involving ultraviolet photocatalytic destruction of PFOA by a BOHP suspension revealed that catalytic activity was influenced by the choice of reagents and their variable effect on surface facet growth and crystal defects in the resulting microparticles. Together, this work provides a strategy for crystal facet and surface defect engineering with the potential to expand to other metal oxides within the hydrothermal system.

A review on superior advanced oxidation and photocatalytic degradation techniques for perfluorooctanoic acid (PFOA) elimination from wastewater

Perfluorooctanoic acid (PFOA) has been identified as the most toxic specie of the family of perfluorinated carboxylic acids (PFCAs). It has been widely distributed and frequently detected in environmental wastewater. The compound's unique features such as inherent stability, rigidity, and resistance to harsh chemical and thermal conditions, due to its multiple and strong C-F bonds have resulted in its resistance to conventional wastewater remediations. Photolysis and bioremediation methods have been proven to be inefficient in their elimination, hence this article presents intensive literature studies and summarized findings reported on the application of advanced oxidation processes (AOPs) and photocatalytic degradation techniques as the best alternatives for the PFOA elimination from wastewater. Techniques of persulfate, photo-Fenton, electrochemical, photoelectrochemical and photocatalytic degradation have been explored and their mechanisms for the degradation and defluorination of the PFOA have been demonstrated. The major advantage of AOPs techniques has been centralized on the generation of active radicals such as sulfate (SO₄^•-) hydroxyl (•OH). While for the photocatalytic process, photogenerated species (electron (e) and holes (h ⁺ _vb)) initiated the process. These active radicals and photogenerated species possessed potentiality to attack the PFOA molecule and caused the cleavage of the C-C and C-F bonds, resulting in its efficient degradation. Shorter-chain PFCAs have been identified as the major intermediates detected and the final stage entails its complete mineralization to carbon dioxide (CO₂) and fluoride ion (F^-). The prospects and challenges associated with the outlined techniques have been highlighted for better understanding of the subject matter for the PFOA elimination from real wastewaters.

Cationic surfactants influencing the enhancement of energy efficiency for perfluorooctanoic acid (PFOA) removal in the electrocoagulation-flotation (ECF) system

From an environmental perspective, approaching sustainability requires a fundamental conceptual shift from the wastewater treatment process toward integrated treatment systems that consider efficient and effective utilization. This study aims to investigate the effects of different surfactants on the removal of perfluorooctanoic acid (PFOA). We used cationic surfactants as both frothers and collectors in the electrocoagulation-flotation (ECF) method to improve the removal efficiency of PFOA. The results showed that, under a monopolar aluminum electrode and with an initial PFOA concentration of 0.25 mM, the ECF method with decyl-trimethyl-ammonium bromide (DTAB) was able to remove over 98% of PFOA within 10 min. Cationic surfactants with a similar linear alkyl chain shape to PFOA, but a longer chain length, are more effective at removing PFOA through the ECF process. The removal mechanism is thought to involve co-precipitation with aluminum hydroxides through Al-F bonding, co-flotation with cationic surfactants, and mixed micelle formation with cationic surfactants. The optimal conditions were tested in both synthetic and realistic wastewater matrices and produced similar results. It has the potential for real wastewater application. The energy yield (G₅₀) of ECF with 5 mM DTAB is 497 g·kWh^-1, superior to other treatments, and is an extremely energy-effective method for separating PFOA from wastewater.

Multiple interactions steered high affinity toward PFAS on ultrathin layered rare-earth hydroxide nanosheets: Remediation performance and molecular-level insights

The global occurrence of per- and polyfluoroalkyl substances (PFAS) in aquatic systems has raised concerns about their adverse effects on ecosystems and human health. Adsorption is a promising technique for the remediation of PFAS, yet effective adsorbents with rapid uptake kinetics and high adsorption capacity are still in high demand, and molecular-level understanding of the interfacial adsorption mechanisms is lacking. In this study, we developed a superior layered rare-earth hydroxide (LRH) adsorbent, ultrathin Y₂(OH)_4.86Cl_1.44·1·07H₂O (namely YOHCl) nanosheets, to achieve the effective removal of perfluorooctanoic acid (PFOA). YOHCl nanosheets exhibited ultra-high adsorption capacity toward PFOA (up to 957.1 mg/g), which is 1.9 times and 9.3 times higher than the state-of-the-art layered double hydroxides (MgAl-LDH) and benchmark granular activated carbon (GAC) under the same conditions, respectively. Furthermore, YOHCl nanosheets pose stable performance on the removal of PFOA under various water matrices with robust reusability. We also developed YOHCl-based continuous-flow column, demonstrating its promise in simultaneously removing multiple PFAS with wide range of chain lengths at environmentally relevant concentrations. With the molecular-level investigations, we have revealed that multi-mechanism, including ion exchange, electrostatic attraction and bidentate/bridging coordination, contributed to the strong PFOA-YOHCl affinity, leading to the ultra-high adsorption capacity of PFOA. We have provided emerging LRHs-based adsorbents for the effective remediation of PFAS with molecular-level insights on the interfacial mechanisms.

Removal of perfluorooctanoic acid via polyethyleneimine modified graphene oxide: Effects of water matrices and understanding mechanisms

This research aimed to evaluate the adsorption behaviors and mechanisms of perfluorooctanoic acid (PFOA) onto polyethyleneimine modified graphene oxide (GO-PEI) from aqueous solutions. The adsorption capacity was significantly improved by doping polyethyleneimine (PEI) onto graphene oxide (GO). The Brunauer-Emmett-Teller (BET) isotherm model was considered as the best isotherm model in describing the PFOA adsorption onto GO-PEI3 (w_PEI/w_GO = 3). GO-PEI3 exhibited high adsorption capacity (q_e = 368.2 mg/g, calculated from BET isotherm model) and excellent stability. The maximum monolayer amount of PFOA adsorption onto GO-PEI3 (q_m = 231.2 mg/g) was successfully evaluated. The calculated saturated concentration (C_s = 169.9 mg/L) of PFOA on GO-PEI3 closely agrees with its critical micelle concentration (CMC = 157.0 mg/L), suggesting the formation of multilayer hemi-micelles or micelles PFOA structures on the surface of GO-PEI3. PFOA adsorption onto GO-PEI3 was inhibited by several factors including: the presence of humic acid (HA) by competing with the adsorption sites, background salts through the double-layer compression effect, and the competition from soluble ions for the amine or amide functional groups on GO-PEI3. Finally, both the FT-IR and XPS results confirmed that the adsorption of PFOA onto GO-PEI3 was through electrostatic attraction and hydrophobic interaction (physical adsorption), but not chemical adsorption. This work provides fundamental knowledge both in understanding the adsorption behavior through the BET isotherm model and in developing a stable adsorbent for PFOA adsorption. In addition, the findings highlight the potential of PFOA remediation from wastewater systems using GO-PEI in engineering applications.

Increasing electron density by surface plasmon resonance for enhanced photocatalytic CO2 reduction

The photocatalytic CO₂ reduction reaction is a multi-electron process, which is greatly affected by the surface electron density. In this work, we synthesize Ag clusters supported on In₂O₃ plasmonic photocatalysts. The Ag-In₂O₃ compounds show remarkedly enhanced photocatalytic activity for CO₂ conversion to CO compared to pristine In₂O₃. In the absence of any co-catalyst or sacrificial agent, the CO evolution rate of optimal Ag-In₂O₃-10 is 1.56 μmol/g/h, achieving 5.38-folds higher than that of In₂O₃ (0.29 μmol/g/h). Experimental verification and DFT calculation demonstrate that electrons transfer from Ag clusters to In₂O₃ on Ag-In₂O₃ compounds. In Ag-In₂O₃ compounds, Ag clusters serving as electron donators owing to the SPR behaviour are not helpful to decline photo-induced charge recomnation rate, but can provide more electron for photocatalytic reaction. Overall, the Ag clusters promote visible-light absorption and accelerate photocatalytic reaction kinetic for In₂O₃, resulting in the photocatalytic activity enhancement of Ag-In₂O₃ compounds. This work puts insight into the function of plasmonic metal on enhancing photocatalysis performance, and provides a feasible strategy to design and fabricate efficient plasmonic photocatalysts.

Complete mechanochemical defluorination of perfluorooctanoic acid using Al2O3 and Al powders through matching electron-mediated reduction with decarboxylation

This work reports a mechanochemical (MC) method for complete defluorination of perfluorooctanoic acid (PFOA) by using Al and Al₂O₃ as milling agents. Both the Al/Al₂O₃ molar ratio ( [Formula: see text] ) and the pre-thermal treatment of Al₂O₃ strongly influenced the defluorination of PFOA. When commercial γ-Al₂O₃ was pre-treated at 1200 °C, the use of Al and heat-treated γ-Al₂O₃ with [Formula: see text] of 1: 1 led to PFOA defluorination of 100% after ball milling for 26 min at 350 rpm, being much higher than those (8.3%-58.1%) for using singlet milling agents or binary milling agents containing γ-Al₂O₃ pre-heated at temperatures lower than 700 °C. It was clarified that the carboxylate-mediated adsorption of PFOA on Al₂O₃ was essential for the MC decarboxylation as a degradation initiation step, and the in-situ generated electron on milled Al consequently caused the reductive dissociation of C-F bonds in the decarboxylation intermediate. A larger [Formula: see text] increased the in-situ electron generation rate (r_e), and a higher heat-treatment temperature decreased OH^-/H₂O adsorbed on Al₂O₃ to low the PFOA decarboxylation rate (r_dec). The r_e/r_dec ratio determined defluorination pathways, and the percentage of the defluorination of PFOA in its total degradation including the generation of any degradation intermediates increased linearly with increasing r_e/r_dec.

Electrooxidation of per- and polyfluoroalkyl substances in chloride-containing water on surface-fluorinated Ti4O7 anodes: Mitigation and elimination of chlorate and perchlorate formation

Electrooxidation (EO) has been shown effective in degrading per- and polyfluoroalkyl substances (PFASs) in water, but concurrent formation of chlorate and perchlorate in the presence of chloride is of concern due to their toxicity. This study examined EO treatment of three representative PFASs, perfluorooctane sulfonate (PFOS), perfluorooctanoic acid (PFOA) and 6:2 fluorotelomer sulfonate (6:2 FTS), in chloride-containing solutions on pristine and surface-fluorinated Ti₄O₇ anodes having different percentage of surface fluorination. The experiment results indicate that surface fluorination of Ti₄O₇ anodes slightly inhibited PFAS degradation, while significantly decreased the formation of chlorate and perchlorate. Further studies with spectroscopic and electrochemical characterizations and density functional theory (DFT) computation reveal the mechanisms of the impact on EO performance by anode fluorination. In particular, chlorate and perchlorate formation were fully inhibited when fluorinated Ti₄O₇ anode was used in reactive electrochemical membrane (REM) under a proper anodic potential range (<3.0 V vs Standard Hydrogen Electrode), resulting from slower intermediate reaction steps and short residence time of the REM system. The results of this study provide a basis for design and optimization of modified Ti₄O₇ anodes for efficient EO treatment of PFAS while limiting chlorate and perchlorate formation.

Photodegradation of per- and polyfluoroalkyl substances in water: A review of fundamentals and applications

Per- and polyfluoroalkyl substances (PFAS) are persistent, mobile, and toxic chemicals that are hazardous to human health and the environment. Several countries, including the United States, plan to set an enforceable maximum contamination level for certain PFAS compounds in drinking water sources. Among the available treatment options, photocatalytic treatment is promising for PFAS degradation and mineralization in the aqueous solution. In this review, recent advances in the abatement of PFAS from water using photo-oxidation and photo-reduction are systematically reviewed. Degradation mechanisms of PFAS by photo-oxidation involving the holes (h_vb⁺) and oxidative radicals and photo-reduction using the electrons (e_cb^-) and hydrated electrons (e_aq^-) are integrated. The recent development of innovative heterogeneous photocatalysts and photolysis systems for enhanced degradation of PFAS is highlighted. Photodegradation mechanisms of alternative compounds, such as hexafluoropropylene oxide dimer acid (GenX) and chlorinated polyfluorinated ether sulfonate (F-53B), are also critically evaluated. This paper concludes by identifying major knowledge gaps and some of the challenges that lie ahead in the scalability and adaptability issues of photocatalysis for natural water treatment. Development made in photocatalysts design and system optimization forges a path toward sustainable treatment of PFAS-contaminated water through photodegradation technologies.

Removal of PFASs from water by carbon-based composite photocatalysis with adsorption and catalytic properties: A review

Per- and polyfluoroalkyl substances (PFASs) are a class of persistent organic pollutants widely distributed in aquatic environments. The adsorption and photocatalytic methods have been widely used to remove PFASs in water because of their respective advantages. Still, they have apparent defects when used alone. Therefore, the adsorption and photocatalytic technologies are combined through suitable preparation methods, and the excellent properties of the two are used to synergize the treatment of organic pollutants. This strategy of "concentrating" pollutants and then degrading them in a centralized manner plays an essential role in removing trace PFASs. Nevertheless, a review focusing on this kind of adsorption photocatalyst system is lacking. This review will fill this gap and provide a reference for developing a carbon-based composite photocatalyst. Firstly, different carbon-based composite photocatalysts are reviewed in detail, focusing on the differences in various composite materials' excellent adsorption and catalytic properties. Secondly, the factors influencing the removal effect of carbon-based composite photocatalysts are discussed. Thirdly, the removal mechanism of carbon-based composite photocatalysts is summarized in detail. The removal process involves two steps: adsorption and photodegradation. The adsorption process involves multiple cooperative adsorption mechanisms, and photocatalytic degradation includes oxidative and reductive degradation. Fourthly, the comparison of adsorption-photocatalysis with common treatment techniques (including removal rate, range of adaptation, cost, and the possibility of expanding application) is summarized. Finally, the prospects of carbon-based composite photocatalysts for repairing PFASs are given by evaluating the performance of different composites.

Concentrate and degrade PFOA with a photo-regenerable composite of In-doped TNTs@AC

"Concentrate-and-degrade" is an effective strategy to promote mass transfer and degradation of pollutants in photocatalytic systems, yet suitable and cost-effective photocatalysts are required to practice the new concept. In this study, we doped a post-transition metal of Indium (In) on a novel composite adsorptive photocatalyst, activated carbon-supported titanate nanotubes (TNTs@AC), to effectively degrade perfluorooctanoic acid (PFOA). In/TNTs@AC exhibited both excellent PFOA adsorption (>99% in 30 min) and photodegradation (>99% in 4 h) under optimal conditions (25 °C, pH 7, 1 atm, 1 g/L catalyst, 0.1 mg/L PFOA, 254 nm). The heterojunction structure of the composite facilitated a cooperative adsorption mode of PFOA, i.e., binding of the carboxylic head group of PFOA to the metal oxide and attachment of the hydrophobic tail to AC. The resulting side-on adsorption mode facilitates the electron (e^‒) transfer from the carboxylic head to the photogenerated hole (h⁺), which was the major oxidant verified by scavenger tests. Furthermore, the presence of In enables direct electron transfer and facilitates the subsequent stepwise defluorination. Finally, In/TNTs@AC was amenable to repeated uses in four consecutive adsorption-photodegradation runs. The findings showed that adsorptive photocatalysts can be prepared by hybridization of carbon and photoactive semiconductors and the enabled "concentrate-and-degrade" strategy is promising for the removal and degradation of trace levels of PFOA from polluted waters.

Efficient photodegradation of PFOA using spherical BiOBr modified TiO2 via hole-remained oxidation mechanism

Photo-induced holes (h⁺) oxidation is an efficient approach for perfluorooctanoic acid (PFOA; C₇F₁₅COOH) removal. To maintain a high amount of h⁺ on the surface of photocatalysts participating in the PFOA photodegradation could be a critical issue. Herein, a highly efficient spherical BiOBr-modified nano-TiO₂ (P25) was synthesised and used for PFOA photodegradation through direct oxidation with h⁺. A high number of h⁺ could be generated and remain on the surface of P25/BiOBr due to the appropriate position of the conduction band (CB) and valence band (VB) levels between P25 and BiOBr. Meanwhile, PFOA molecules were coordinated to the P25/BiOBr's surface via unidentate binding, being directly activated and oxidised by h⁺, resulting in a decomposition yield of 99.5% (100 mg/L) under simulated solar light irradiation within 100 min, at the initial pH condition (3.5). A stepwise photodegradation pathway was proposed due to the significant intermediates detected as the short-chain perfluorinated carboxylic acids (C2-C7). Reactive oxygen species (ROS) generation, scavenging and trapping analysis indicated that the direct oxidation on h⁺ followed PFOA degradation. In a real aqueous environment of Tangxun lake (adjusted pH 3.5), stable common anions and natural organic matter (NOM) would restrain the PFOA photodegradation. However, adding 10 mg/L of NO₃^- or HA could reduce the inhibition effect of PFOA photodegradation. These findings gave an alternative strategy to drive an h⁺ directly oxidation to treat PFOA contaminated water bodies.

Integrated Photocatalytic Reduction and Oxidation of Perfluorooctanoic Acid by Metal-Organic Frameworks: Key Insights into the Degradation Mechanisms

The high porosity and tunability of metal-organic frameworks (MOFs) have made them an appealing group of materials for environmental applications. However, their potential in the photocatalytic degradation of per- and polyfluoroalkyl substances (PFAS) has been rarely investigated. Hereby, we demonstrate that over 98.9% of perfluorooctanoic acid (PFOA) was degraded by MIL-125-NH₂, a titanium-based MOF, in 24 h under Hg-lamp irradiation. The MOF maintained its structural integrity and porosity after three cycles, as indicated by its crystal structure, surface area, and pore size distribution. Based on the experimental results and density functional theory (DFT) calculations, a detailed reaction mechanism of the chain-shortening and H/F exchange pathways in hydrated electron (e_aq^-)-induced PFOA degradation were revealed. Significantly, we proposed that the coordinated contribution of e_aq^- and hydroxyl radical (^•OH) is vital for chain-shortening, highlighting the importance of an integrated system capable of both reduction and oxidation for efficient PFAS degradation in water. Our results shed light on the development of effective and sustainable technologies for PFAS breakdown in the environment.

Nanoparticle-embedded hydrogel synthesized electrodes for electrochemical oxidation of perfluorooctanoic acid (PFOA) and perfluorooctanesulfonic acid (PFOS)

In this study, sliver (Ag) and gold (Au) nanoparticles (NPs) were embedded on poly (acrylic acid) (PAA)/poly (allylamine) hydrochloride (PAH) hydrogel fibers for improved electrochemical oxidation (EO) of perfluorooctanoic acid (PFOA) and perfluorooctanesulfonic acid (PFOS) removal. The NPs-loaded PAA/PAHs shows the better charge transport compared to the ceramic nanofiber membranes (CNM) electrodes. At 10 mA cm^-2 of current density, the Ag-PAA/PAH electrodes showed a faster removal of PFAS compared to the Ag-CNM electrode probably due to large surface area-volume ratio and high porosity from the hydrogel. Among NPs-loaded PAA/PAH electrodes, the Ag/Au-PAA/PAH electrodes showed the highest removal of PFOA (72%) and PFOS (91%) in 2 h with the maximum removal rate of PFOA (0.0046 min^-1) and PFOS (0.0093 min^-1). The rapid PFOS removal is possibly due to the high activity of electron transfer with a higher redox potential of SO₄^•- than •OH. The highly stable F^- generation was obtained from each electrode during reproducibility (n = 3). The net energy consumption from Ag/Au-PAA/PAH electrode was 164.9 kWh m^-3 for 72% PFOA removal and 90 kWh m^-3 for 91% PFOS removal, respectively. The developed Au-PAA/PAH electrodes were applied to lake water samples and showed acceptable PFOS removal (65%) with relative standard deviations (RSD) of 10.2% (n = 3) at 10 mA cm^-2 of current density. Overall, the NP-embedded hydrogel nanofibers were proven to be a promising sustainable catalyst for the electrochemical PFAS oxidation in water.

Integrated flow anodic oxidation and ultrafiltration system for continuous defluorination of perfluorooctanoic acid (PFOA)

While flow anodic oxidation systems can efficiently generate hydroxyl radicals (·OH) and significantly enhance direct electron transfer (DET) processes that result in the oxidation of target contaminants via the charge percolating network of flow anode particles, challenges remain in constructing a flow anodic oxidation system that can be operated continuously with stable performance. Here we incorporate an ultrafiltration (UF) membrane module into the flow anodic oxidation system and achieve the continuous defluorination of perfluorooctanoic acid (PFOA) for 12 days with high efficiency (94.1%) and reasonable energy consumption (38.1 Wh mg^-1) compared to other advanced oxidation processes by using a mixture of conducting Ti_xO_2x-1 and Pd/CNT particles as the flow anode. The results indicate that DET, ·OH mediated oxidation and adsorption processes play critical roles in the degradation of PFOA during the flow anodic oxidation processes. The synergistic effect of the Ti_xO_2x-1 and Pd/CNT particles enhances the defluorination efficiency by 3.2 times at 4.5 V vs Ag/AgCl compared to the control experiment (no flow anode particles present) and promotes the release of F^- into solution while other intermediate products remain adsorbed to the surface of the Pd/CNT particles. Although the Pd/CNT particles were oxidized after the long-term operation, no obvious Pd ion leakage into solution was observed. Results of this study support the feasibility of continuous operation of a flow anode/UF system with stable performance and pave the way for the translation of this advanced oxidation technology to practical application.

Application of Hydrothermal Alkaline Treatment for Destruction of Per- and Polyfluoroalkyl Substances in Contaminated Groundwater and Soil

Hydrothermal alkaline treatment (HALT) can effectively degrade per- and polyfluoroalkyl substances (PFASs) present in aqueous film-forming foam (AFFF). However, information is lacking regarding the treatment of PFASs in actual groundwater and soil from AFFF-impacted sites, especially for complex soil matrices. Given the lack of studies on direct soil treatment for PFAS destruction, we herein applied HALT to two groundwater samples and three soil samples from AFFF-impacted sites and characterized the destruction of PFASs using high-resolution mass spectrometry. Results showed that the 148 PFASs identified in all collected field samples, including 10 cationic, 98 anionic, and 40 zwitterionic PFASs, were mostly degraded to nondetectable levels within 90 min when treated with 5 M NaOH at 350 °C. The near-complete defluorination, as evidenced by fluoride release measurements, confirmed the complete destruction of PFASs. While many structures, including perfluoroalkyl carboxylic acids and polyfluorinated substances, were readily degraded, perfluoroalkyl sulfonates (PFSAs, C_nF_2n+1-SO₃^-), most notably with short chain lengths (n = 3-5), were more recalcitrant. Rates of PFSA destruction in groundwater samples were similar to those measured in laboratory water solutions, but reactions in soil were slow, presumably due to base-neutralizing properties of the soil. Further, the degradation of PFASs in groundwaters and soils was found to be a function of reaction temperature, NaOH concentration, and reaction time. These findings have important implications for the remediation of AFFF-impacted sites.

High-performance photocatalytic decomposition of PFOA by BiOX/TiO2 heterojunctions: Self-induced inner electric fields and band alignment

BiOX (X = Cl, Br and I) and BiOX/TiO₂ photocatalysts were prepared by a facile hydrothermal approach. The BiOX/TiO₂ heterojunctions demonstrated significantly enhanced efficiency for photocatalytic decomposition of perfluorooctanoic acid (PFOA) compared with sole BiOX or TiO₂. PFOA (10 mg L¹) was completely degraded by BiOCl(Br)/TiO₂ in 8 h. Moreover, BiOCl/TiO₂ attained deep decomposition of PFOA with a high defluorination ratio of 82%. The p-n heterojunctions between BiOX and TiO₂ were confirmed by a series of characterizations. The photo-induced holes would migrate from the valance band (VB) of TiO₂ to BiOX, driven by the built-in electric field (BIEF) near the interfaces of p-n heterojunctions, the inner electric fields (IEF) in BiOX and the higher VB position of BiOX. The X-ray diffraction (XRD) and TEM characterizations indicated that TiO₂ combined with BiOX along the [110] facet, which facilitated photo-induced electron transfer in the [001] direction, thus benefiting PFOA decomposition.

Photocatalytic degradation of perfluoroalkyl substances in water by using a duo-functional tri-metallic-oxide hybrid catalyst

The recalcitrant nature of perfluoroalkyl substances (PFASs) urges scientists to discover solutions to permanently remove PFAS contaminations from water with less energy in contrast to incineration. Herein, a duo-functional tri-metallic-oxide (f-TMO) hybrid photocatalyst was developed via a facile process, which displayed both high adsorption capacity and high defluorination rate of a series of PFASs including PFOA, PFOS, PFHpA, PFHxA and PFBA due to the generated holes/electrons (h⁺/e^-) and multi-radicals such as O₂^•- and SO₄^•-. Particularly the Langmuir adsorption capacities up to 827.84 and 714.46 mg g^-1 along with the adsorption efficiency of 99.8% and 99.4% for PFOS and PFOA were respectively achieved. A defluorination ratio of as high as 74.8% with PFOA and a ratio up to 67.6% with PFOS were respectively received. Over 98% PFOA molecules were degraded within as fast as 15 min under initial concentrations ranging from 1 ppb to 1000 ppb, which demonstrates an excellent degradation kinetics. As for the sulfonic acid of PFOS, an as high as 95.5% degradation efficiency was obtained within 300 min. The degradation rates were 4.5 mg L^-1 h^-1 for PFOA and 0.54 mg L^-1 h^-1 for PFOS, respectively. In parallel, the f-TMO photocatalyst still exhibited a >96.2% degradation efficiency after eight regeneration cycles. The high physical adsorption capacity and high defluorination rate make this f-TMO catalyst promising applications in removing various PFASs from a broad range of residential and industrial water systems.

Degradation of perfluoroalkyl substances using UV/Fe0 system with and without the presence of oxygen

The wide presence of per- and poly-fluoroalkyl substances (PFAS) in the environment is a global concern, thus their degradation is an imminent task. In this study, oxidative and/or reductive degradation of three representative PFAS - perfluorooctanoic acid (PFOA), perfluorononanoic acid (PFNA), and perfluorooctane sulfonate (PFOS) was achieved using nanoscale zero-valent iron (Fe⁰ NPs) under ultraviolet (UV) light, both with and without the presence of oxygen. Higher degradation and defluorination rates were obtained for a longer chain PFNA compared to PFOA, and a higher removal of PFAS was achieved without the presence of O₂ compared to that with O₂. The degradation followed first-order reaction kinetics, and obtained the highest rates of 97.6, >99.9, and 98.5% without the presence of O₂ for PFOA, PFNA, and PFOS, respectively. The degradation rates increased with an increase in the nanoparticle concentrations in the range of 1-100 mg/L. In addition to fluoride ions, shorter chain perfluorocarboxylic acids (PFCAs) were detected as the main intermediates during PFAS degradation; PFHpS and 6:2 FTS were also detected during PFOS degradation. Hydroxyl radicals (·OH) and superoxide radicals (·O₂^-) were not involved in the degradation of PFOA, but likely involved in the degradation of PFOS. Emerging contaminants PFAS degradation using the UV/Fe⁰ system is a cost-effective technology owing to the low cost and recyclability of Fe⁰ nanomaterials, low energy consumption in the system, and its capability to degrade PFAS both with and without the presence of oxygen. This technology can be potentially applied to treat PFAS-contaminated waters in the environment.

Theoretical and experimental insights into the mechanisms of C6/C6 PFPiA degradation by dielectric barrier discharge plasma

As an emerging alternative legacy perfluoroalkyl substance, C6/C6 PFPiA (perfluoroalkyl phosphinic acids) has been detected in aquatic environments and causes potential risks to human health. The degradation mechanisms of C6/C6 PFPiA in a dielectric barrier discharge (DBD) plasma system were explored using validated experimental data and density functional theory (DFT) calculations. Approximately 94.5% of C6/C6 PFPiA was degraded by plasma treatment within 15 min at 18 kV. A relatively higher discharge voltage and alkaline conditions favored its degradation. C6/C6 PFPiA degradation was attributed to attacks of •OH, •O₂^-, and ¹O₂. Besides PFHxPA and C2 -C6 shorter-chain perfluorocarboxylic acids, several other major intermediates including C4/C6 PFPiA, C4/C4 PFPiA, and C3/C3 PFPiA were identified. According to DFT calculations, the potential energy surface was proposed for possible reactions during C6/C6 PFPiA degradation in the discharge plasma system. Integrating the identified intermediates and DFT results, C6/C6 PFPiA degradation was deduced to occur by stepwise losing CF₂, free radical polymerization, and C-C bond cleavage. Furthermore, the DBD plasma treatment process decreased the toxicity of C6/C6 PFPiA to some extent. This study provides a comprehensive understanding of C6/C6 PFPiA degradation by plasma advanced oxidation.

Efficient removal of PFOA with an In2O3/persulfate system under solar light via the combined process of surface radicals and photogenerated holes

The environmental persistence, high toxicity and wide spread presence of perfluorooctanoic acid (PFOA) in aquatic environment urgently necessitate the development of advanced technologies to eliminate PFOA. Here, the simultaneous application of a heterogeneous In₂O₃ photocatalyst and homogeneous persulfate oxidation (In₂O₃/PS) was demonstrated for PFOA degradation under solar light irradiation. The synergistic effect of direct hole oxidation and in-situ generated radicals, especially surface radicals, was found to contribute significantly to PFOA defluorination. Fourier infrared transform (FTIR) spectroscopy, Raman, electrochemical scanning microscope (SECM) tests and density functional theory (DFT) calculation showed that the pre-adsorption of PFOA and PS onto In₂O₃ surface were dramatically critical steps, which could efficiently facilitate the direct hole oxidation of PFOA, and boost PS activation to yield high surface-confined radicals, thus prompting PFOA degradation. Response surface methodology (RSM) was applied to regulate the operation parameters for PFOA defluorination. Outstanding PFOA decomposition (98.6%) and near-stoichiometric equivalents of fluorides release were achieved within illumination 10 h. An underlying mechanism for PFOA destruction was proposed via a stepwise losing CF₂ unit. The In₂O₃/PS remediation system under solar light provides an economical, sustainable and environmentally friendly approach for complete mineralization of PFOA, displaying a promising potential for treatment of PFOA-containing water.

Effective Breaking of the Fluorocarbon Chain by the Interface Bi2O2X···PFOA Complex Strategy via Coordinated Se on Construction of the Internal Photogenerated Carrier Pathway

The destruction of perfluorooctanoic acid (PFOA) from outside was inhibited by the "barrel spiral" barrier, but the construction of the photocatalyst-PFOA complex provided a direct attack on photogenerated reactive species (RSs). Here, we investigated the bridging ability of bismuth oxychalcogenide (Bi₂O₂X) for constructing an effective photocarrier pathway to PFOA. The experimental results and DFT calculations showed that a more intense internal access of Bi₂O₂Se was built via the terminal carboxylate tail, and the weaker electrostatic interaction of Bi-Se bonds helped realize the smaller band gap and slower recombination of photocarriers, thereby inhibiting the invalid annihilation of holes with H₂O and facilitating the transformation of electrons to O₂^-•. The pseudo-first-order rate coefficient (k_obs) was 2 and 4 times higher than Bi₂O₂S and TiO₂, respectively, showing the outstanding photocatalytic activity of Bi₂O₂Se. A broad pH (4-8) adaptability of Bi₂O₂Se was observed for defluorination, especially in alkali condition. This new understanding may inspire the development of Se-coordinated catalysts.

Quantification of perfluorooctanoic acid decomposition mechanism applying negative voltage to anode during photoelectrochemical process

Perfluorooctanoic acid (PFOA) is a carcinogen with a high binding energy between fluorine and carbon and is symmetrically linked, making it difficult to treat. In this study, a self-doped TiO₂ nanotube array (TNTA) was used as the anode and platinum as the cathode to quantify the PFOA removal mechanism using a photoelectrochemical (PEC) system. The external voltage was negative compared to that of the anode. In addition, NO₃^- and t-BuOH were used as scavengers to quantify the PFOA oxidation/reduction mechanism in the PEC system. As a result of the study, TNTA crystals are TiO₂ anatase, and the band gap energy was 3.42. The synergy index of PEC was 1.25, and the best electrolyte was SO₄^2-. The PFOA decomposition activation energy corresponds to 70.84 kJ mol^-1. Moreover, ΔH^# and ΔS^# correspond to 68.34 kJ mol^-1 and 0.190 kJ mol^-1 K^-1, respectively. When the external negative voltage was 1 V, the contributions of the oxidation/reduction reaction during PFOA decomposition were 60% and 40%, and when the external negative voltage was 5 V, the contributions of the redox reaction were 45% and 55%. As the external negative voltage increased, the contribution of the reduction reaction increased as the number of electrons applied to the anode increased. When PFOA was decomposed, the by-products were C₇F₁₃O₂H, C₆F₁₁O₂H, C₅F₉O₂H, and C₄F₇O₂H, respectively. This study is expected to be used as basic data for research on the effects of other factors on the oxidation/reduction as well as the selection of anode and cathode materials on the decomposition of pollutants other than PFOA when using a PEC system.

Occurrence and removal of poly/perfluoroalkyl substances (PFAS) in municipal and industrial wastewater treatment plants

The presence of poly- and perfluoroalkyl substances (PFAS) has caused serious problems for drinking water supplies especially at intake locations close to PFAS manufacturing facilities, wastewater treatment plants (WWTPs), and sites where PFAS-containing firefighting foam was regularly used. Although monitoring is increasing, knowledge on PFAS occurrences particularly in municipal and industrial effluents is still relatively low. Even though the production of C8-based PFAS has been phased out, they are still being detected at many WWTPs. Emerging PFAS such as GenX and F-53B are also beginning to be reported in aquatic environments. This paper presents a broad review and discussion on the occurrence of PFAS in municipal and industrial wastewater which appear to be their main sources. Carbon adsorption and ion exchange are currently used treatment technologies for PFAS removal. However, these methods have been reported to be ineffective for the removal of short-chain PFAS. Several pioneering treatment technologies, such as electrooxidation, ultrasound, and plasma have been reported for PFAS degradation. Nevertheless, in-depth research should be performed for the applicability of emerging technologies for real-world applications. This paper examines different technologies and helps to understand the research needs to improve the development of treatment processes for PFAS in wastewater streams.

Treatment of electrochemical plating wastewater by heterogeneous photocatalysis: the simultaneous removal of 6:2 fluorotelomer sulfonate and hexavalent chromium

6:2 fluorotelomer sulfonate (6:2 FtS) is being widely used as a mist suppressant in the chromate (Cr(vi)) plating process. As a result, it is often present alongside Cr(vi) in the chromate plating wastewater (CPW). While the removal of Cr(vi) from CPW has been studied for decades, little attention has been paid to the treatment of 6:2 FtS. In this study, the removal of Cr(vi) and 6:2 FtS by Ga2O3, In2O3, and TiO2 photocatalysts was investigated. In the Ga2O3/UVC system, over 95% of Cr(vi) was reduced into Cr(iii) after only 5 min. Simultaneously, 6:2 FtS was degraded into F- and several perfluorocarboxylates. The predominant reactive species responsible for the degradation of 6:2 FtS in the Ga2O3 system were identified to be hVB + and O2˙-. In addition, it was observed that the presence of Cr(vi) helped accelerate the degradation of 6:2 FtS. This synergy between Cr(vi) and 6:2 FtS was attributable to the scavenging of eCB - by Cr(vi), which retarded the recombination of eCB - and hVB +. The In2O3/UVC system was also capable of removing Cr(vi) and 6:2 FtS, although at significantly slower rates. In contrast, poor removal of 6:2 FtS was achieved with the TiO2/UVC system, because Cr(iii) adsorbed on TiO2 and inhibited its reactivity. Based on the results of this study, it is proposed that CPW can be treated by a treatment train that consists of an oxidation-reduction step driven by Ga2O3/UVC, followed by a neutralization step that converts dissolved Cr(iii) into Cr(OH)3(S).

A Review on Emerging Pollutants in the Water Environment: Existences, Health Effects and Treatment Processes

Emerging pollutants (EPs), also known as micropollutants, have been a major issue for the global population in recent years as a result of the potential threats they bring to the environment and human health. Pharmaceuticals and personal care products (PPCPs), antibiotics, and hormones that are used in great demand for health and cosmetic purposes have rapidly culminated in the emergence of environmental pollutants. EPs impact the environment in a variety of ways. EPs originate from animal or human sources, either directly discharged into waterbodies or slowly leached via soils. As a result, water quality will deteriorate, drinking water sources will be contaminated, and health issues will arise. Since drinking water treatment plants rely on water resources, the prevalence of this contamination in aquatic environments, particularly surface water, is a severe problem. The review looks into several related issues on EPs in water environment, including methods in removing EPs. Despite its benefits and downsides, the EPs treatment processes comprise several approaches such as physico-chemical, biological, and advanced oxidation processes. Nonetheless, one of the membrane-based filtration methods, ultrafiltration, is considered as one of the technologies that promises the best micropollutant removal in water. With interesting properties including a moderate operating manner and great selectivity, this treatment approach is more popular than conventional ones. This study presents a comprehensive summary of EP’s existence in the environment, its toxicological consequences on health, and potential removal and treatment strategies.

Significant Role of Oxygen Dopants in Photocatalytic PFCA Degradation over h-BN

The activation of the C(sp³)-F bond is extremely difficult due to its unreactive nature. The importance of this bond activation is recently highlighted because extensive distribution of perfluorocarboxylic acids (PFCAs) (C_nF_2n+1COOH) has emerged as a challenging environmental issue. Photocatalytic degradation of PFCAs over a few semiconducting light absorbers is known to remove these water and soil resilient contaminants but with limited efficiency. This work reports density functional theory calculations, through which we present a detailed mechanistic study of photocatalytic degradation of CF₃COOH (the shortest member of the PFCA family) over hexagonal boron nitride (h-BN). Our results clearly demonstrate that the existence of point defects is necessary to activate the h-BN plane for photocatalytic dissociation of the C-F bond. Specifically, we show that vacancies create strong Lewis acid or base sites (B or N vacancy, respectively) that facilitate the activation of the C(sp³)-F bond considerably. Furthermore, this study presents vivid theoretical evidence for the significant role of oxygen dopants, which mitigate the strength of the active sites and promote PFCA degradation over h-BN. Our calculations suggest that while the very stable intermediates generated during the reaction, in the case of h-BN with B or N vacancies, practically poison the catalyst, oxygen dopants make the degradation much more plausible and controllable. This work thus provides both an explanation for recently observed photocatalytic activity of h-BN to decompose PFCAs and valuable insights for exploring defected two-dimensional materials for activating and removing the fluorine-containing contaminants from water and soil.

Improvement mechanism of NO photocatalytic degradation performance of self-cleaning synergistic photocatalytic coating under high humidity

Photocatalytic coating has been widely studied as a promising material to remove air pollutants. However, the effectiveness and long-term effect of photocatalysis in high relative humidity environment is still the main challenge in this field. In this study, a fluorinated WO₃-TiO₂ nanorods/SiO₂ epoxy photocatalytic superamphiphobic coating (FTSE coating) was prepared using a simple spraying method. The micromorphology and chemical composition of FTSE coating was characterized by SEM, EDS, FT-IR, XPS and TGA techniques. The advanced contact angle and hysteresis angle test show that the FTSE coating had excellent superamphiphobicity. The mechanical abrasions, corrosion resistance and UV aging tests show that the FTSE coating exhibited reasonable durability. Besides, the NO degradation efficiency of hydrophilic and superamphiphobic coatings with contact angles of 20.19°, 87.74°, 162.93° and 164.47° was tested in different humidity environment. The results showed that the superamphiphobic coating exhibited more superior photocatalytic degradation efficiency (84.02%) than the hydrophilic coating (51.38%) at a high relative humidity (RH=98%). Finally, FTSE coating exhibited prominent photocatalytic stability and the synergistic effect of photocatalysis and self-cleaning. After 30 d outdoor weathering test, the NO degradation efficiency decreased by 13.07% and recovered to the original level after flushing. The improvement mechanism of NO degradation performance was proposed based on the characteristics of superamphiphobic surface.

Light-Induced Advanced Oxidation Processes as PFAS Remediation Methods: A Review

PFAS substances, which have been under investigation in recent years, are certainly some of the most critical emerging contaminants. Their presence in drinking water, correlated with diseases, is consistently being confirmed by scientific studies in the academic and health sectors. With the aim of developing new technologies to mitigate the water contamination problem, research activity based on advanced oxidation processes for PFAS dealkylation and subsequent mineralization is active. While UV radiation could be directly employed for decontamination, there are nevertheless considerable problems regarding its use, even from a large-scale perspective. In contrast, the use of cheap, robust, and green photocatalytic materials active under near UV-visible radiation shows interesting prospects. In this paper we take stock of the health problems related to PFAS, and then provide an update on strategies based on the use of photocatalysts and the latest findings regarding reaction mechanisms. Finally, we detail some brief considerations in relation to the economic aspects of possible solutions.

Engineering and modeling perspectives on photocatalytic reactors for water treatment

The debate on whether photocatalysis can reach full maturity at commercial level as an effective and economical process for treatment and purification of water and wastewater has recently intensified. Despite a bloom of scientific investigations in the last 30 years, particularly with regards to innovative photocatalytic materials, photocatalysis has so far seen a few industrial applications. Regardless of the points of view, it has been realized that research on reactor design and modeling are now equally urgent to match the extensive research carried out on innovative photocatalytic materials. In reality, the development of photocatalytic reactors has advanced steadily in terms of modeling and reactor design over the last two decades, though this topic has captured a smaller specialized audience. In this critical review, we introduce the latest developments on photocatalytic reactors for water treatment from an engineering perspective. The focus is on the modeling and design of photocatalytic reactors for water treatment at pilot- or at greater scale. Photocatalytic reactors utilizing both natural sunlight and UV irradiation sources are comprehensively discussed. The most promising photoreactor designs and models are examined giving key design guidelines. Other engineering considerations, such as operation, cost analysis, patents, and several industrial applications of photocatalytic reactors for water treatment are also presented. The dissemination of key photocatalytic reactor design principles among the scientific community and the water industry is currently one of the greatest obstacles in translating PWT research into widespread real-world application.