Enhanced performance of NaOH-modified Pt/TiO2 toward room temperature selective oxidation of formaldehyde

Synthesis of δ-MnO2 via ozonation routine for low temperature formaldehyde removal

Nowadays, it is still a challenge to prepared high efficiency and low cost formaldehyde (HCHO) removal catalysts in order to tackle the long-living indoor air pollution. Herein, δ-MnO2 is successfully synthesized by a facile ozonation strategy, where Mn2+ is oxidized by ozone (O3) bubble in an alkaline solution. It presents one of the best catalytic properties with a low 100% conversion temperature of 85°C for 50 ppm of HCHO under a GHSV of 48,000 mL/(g·hr). As a comparison, more than 6 times far longer oxidation time is needed if O3 is replaced by O2. Characterizations show that ozonation process generates a different intermediate of tetragonal β-HMnO2, which would favor the quick transformation into the final product δ-MnO2, as compared with the relatively more thermodynamically stable monoclinic γ-HMnO2 in the O2 process. Finally, HCHO is found to be decomposed into CO2 via formate, dioxymethylene and carbonate species as identified by room temperature in-situ diffuse reflectance infrared fourier transform spectroscopy. All these results show great potency of this facile ozonation routine for the highly active δ-MnO2 synthesis in order to remove the HCHO contamination.

Enhanced 1,2-dichloroethane removal using g-C3N4/Blue TiO2 nanotube array photoanode in microbial photoelectrochemical cells

The compound 1,2-dichloroethane (1,2-DCA), a persistent and ubiquitous pollutant, is often found in groundwater and can strongly affect the ecological environment. However, the extreme bio-impedance of C-Cl bonds means that a high energy input is needed to drive biological dechlorination. Biotechnology techniques based on microbial photoelectrochemical cell (MPEC) could potentially convert solar energy into electricity and significantly reduce the external energy inputs currently needed to treat 1,2-DCA. However, low electricity-generating efficiency at the anode and sluggish bioreaction kinetics at the cathode limit the application of MPEC. In this study, a g-C3N4/Blue TiO2-NTA photoanode was fabricated and incorporated into an MPEC for 1,2-DCA removal. Optimal performance was achieved when Blue TiO2 nanotube arrays (Blue TiO2-NTA) were loaded with graphitic carbon nitride (g-C3N4) 10 times. The photocurrent density of the g-C3N4/Blue TiO2-NTA composite electrode was 2.48-fold higher than that of the pure Blue TiO2-NTA electrode under light irradiation. Furthermore, the MPEC equipped with g-C3N4/Blue TiO2-NTA improved 1,2-DCA removal efficiency by 45.21% compared to the Blue TiO2-NTA alone, which is comparable to that of a microbial electrolysis cell. In the modified MPEC, the current efficiency reached 69.07% when the light intensity was 150 mW cm-2 and the 1,2-DCA concentration was 4.4 mM. The excellent performance of the novel MPEC was attributed to the efficient direct electron transfer process and the abundant dechlorinators and electroactive bacteria. These results provide a sustainable and cost-effective strategy to improve 1,2-DCA treatment using a biocathode driven by a photoanode.

Efficient and Durable Oxidation Removal of Formaldehyde over Layered Double Hydroxide Catalysts at Room Temperature

Room temperature catalytic oxidation (RTCO) using non-noble metals has emerged as a highly promising technique for removal of formaldehyde (HCHO) under ambient conditions; however, non-noble catalysts still face the challenges related to poor water resistance and low stability under harsh conditions. In this study, we synthesized a series of layered double hydroxides (LDHs) incorporating various dual metals (MgAl, ZnAl, NiAl, NiFe, and NiTi) for formaldehyde oxidation at ambient temperature. Among the synthesized catalysts, the NiTi-LDH catalyst showed an HCHO removal efficiency and CO2 yield close to 100.0%, and exceptional water resistance and chemical stability on running 1300 min. The abundant hydroxyl groups in LDHs directly bonded with HCHO, leading to the production of CO2 and H2O, thus inhibiting the formation of CO, even in the absence of O2 and H2O. The coexistence of O2 effectively reduced the reaction barrier for H2O molecule dissociation, facilitating the formation of hydroxyl groups and their subsequent backfill on the catalyst surface. The mechanisms underlying the involvement and regeneration of hydroxyl groups in room temperature oxidation of formaldehyde were elucidated with the combined in situ DRIFTS, HCHO-TPD-MS, and DFT calculations. This work not only demonstrates the potential of LDH catalysts in environmental applications but also advances the understanding of the fundamental processes involved in room temperature oxidation of formaldehyde.

Modulating the Electronic Structures of Pt on Pt/TiO2 Catalyst for Boosting Toluene Oxidation

Surface hydroxyl groups commonly exist on the catalyst and present a significant role in the catalytic reaction. Considering the lack of systematical researches on the effect of the surface hydroxyl group on reactant molecule activation, the PtOx/TiO2 and PtOx-y(OH)y/TiO2 catalysts were constructed and studied for a comprehensive understanding of the roles of the surface hydroxyl group in the oxidation of volatiles organic compounds. The PtOx/TiO2 formed by a simple treatment with nitric acid presented greatly enhanced activity for toluene oxidation in which the turnover frequency of toluene oxidation on PtOx/TiO2 was around 14 times as high as that on PtOx-y(OH)y/TiO2. Experimental and theoretical results indicated that adsorption/activation of toluene and reactivity of oxygen atom on the catalyst determined the toluene oxidation on the catalyst. The removal of surface hydroxyl groups on PtOx promoted strong electronic coupling of the Pt 5d orbital in PtOx and C 2p orbital in toluene, facilitating the electron transfers from toluene to PtOx and subsequently the adsorption/activation of toluene. Additionally, the weak Pt-O bond promoted the activation of surface lattice oxygen, accelerating the deep oxidation of activated toluene. This study clarifies the inhibiting effect of surface hydroxyl groups on PtOx in toluene oxidation, providing a further understanding of hydrocarbon oxidation.

Enhanced Visible-Light H2O2 Production over Pt/g-C3N4 Schottky Junction Photocatalyst

Photocatalytic for hydrogen peroxide (H2O2) production is thought as a promising technology owing to its clean and green properties with the cheap and easily available raw materials of H2O and O2. Herein, Pt/g-C3N4 Schottky junction photocatalysts with ultralow Pt contents (0.025-0.1 wt %) were successfully fabricated by an impregnation-reduction method. It can efficiently reduce O2 to generate H2O2 without a sacrificial agent under visible-light irradiation. The yield of H2O2 produced over Pt0.05/g-C3N4 with the optimal 0.05 wt % Pt reached 31.82 μM, which was 2.46 times that of g-C3N4 and higher than most of those in the literature. It also showed good stability in three repeated tests. The deposition of highly dispersed metal Pt nanoparticles with low and limited content can expose enough active Pt atoms, significantly enhance the separation efficiency of photogenerated carriers, and reduce its negative effect on H2O2 decomposition, resulting in improved and outstanding efficiency of H2O2 production. The ·O2- radicals were found to be the main active species. The mechanism of photocatalytic H2O2 production was confirmed to be a two-step single electron route (O2 + e-→ ·O2- → H2O2).

Room temperature removal of high-space-velocity formaldehyde boosted by fixing Pt nanoparticles into Beta zeolite framework

Catalytic oxidation of volatile organic compounds like formaldehyde (HCHO) over the noble metals catalysts at room temperature is among the most promising strategies to control indoor pollution but remains one challenge to maximize the efficiency of noble metal species. Herein, we demonstrated the straightforward encapsulation of highly dispersive Pt nanoparticles (NPs) within BEA zeolite and adjacent with the surface hydroxyl groups to reach the synergistic HCHO oxidation at 25 °C. High efficiency and long-term stability was reached under large space velocity (∼100% conversion at 180,000 mL (g_cat × h)^-1 and >95% at 360,000 mL (g_cat × h)^-1), affording rapid elimination rate of 129.4 μmol (g_Pt × s)^-1 and large turnover frequency of 2.5 × 10^-2 s^-1. This is the first synergy example derived from the hydroxyl groups and confined noble metals within zeolites that accelerated the rate-determining step, the formate transformation, in the HCHO elimination.

Room-temperature activation of the C-H bond in the dehydrogenation of ethane over a Cu/TiO2 catalyst

A novel photocatalytic system of Cu/TiO₂ for activation the C-H bond in the dehydrogenation of ethane to ethylene at room temperature is proposed. The optimized 1%-Cu/TiO₂ catalyst achieved C₂H₆ conversion of 1.70%, C₂H₄ selectivity of 98.41%, and exhibited excellent stability. The active site Cu^δ+ showed high dispersion on the TiO₂ surface. Theoretical calculations and in situ diffuse reflectance infrared Fourier transform spectroscopy revealed a reaction mechanism: C₂H₆ is first activated by adsorption over the Cu_4C/TiO₂ catalyst with elongation of the C-H bond, attacked by h⁺/˙OH to form ethyl radicals, which are then converted to C₂H₄.

Effect of preparation method of noble metal supported catalyts on formaldehyde oxidation at room temperature: Gas or liquid phase reduction

Formaldehyde (HCHO) is toxic to the human body and is one of the main threats to the indoor air quality (IAQ). As such, the removal of HCHO is imperative to improving the IAQ, whereby the most useful method to effectively remove HCHO at room temperature is catalytic oxidation. This review discusses catalysts for HCHO room-temperature oxidation, which are categorized according to their preparation methods, i.e., gas-phase reduction and liquid-phase reduction methods. The HCHO oxidation performances, structural features, and reaction mechanisms of the different catalysts are discussed, and directions for future research on catalytic oxidation are reviewed.

Harnessing Waste Heat from Indoor lamps for Sustainable Thermocatalytic Mineralization of Acetaldehyde using Platinized TiO2

This study demonstrates the first reported thermocatalytic oxidation of an indoor volatile organic compound (VOC), acetaldehyde, by harnessing the waste-heat energy from indoor light sources (e.g., halogen lamps) without additional energy inputs. With an optimal Pt-TiO₂ catalyst, the designed catalyst-coated lampshade was successfully activated under waste-heat energy (∼120 °C) and achieved the complete mineralization of CH₃CHO into CO₂ (k = 0.02 min^-1). The catalytic activity of Pt-TiO₂ was extremely dependent on its preparation method which greatly influenced the characteristics (e.g., oxidation state and size) of Pt. The thermocatalytic oxidation mechanism of CH₃CHO over Pt-TiO₂ was investigated, which revealed that O₂ and H₂O sources play vital roles. Although Pt is an expensive noble metal, the thermocatalytic process on the Pt-TiO₂-coated lampshade without additional energy, along with its outstanding activity, can offset the high material cost. The proposed strategy offers a sustainable and feasible method for the degradation of indoor VOCs.

Acid-Modified Sepiolite-Supported Pt (Noble Metal) Catalysts for HCHO Oxidation at Ambient Temperature

The critical need to enhance the quality of indoor air leads to the improvement of catalyst activity for the removal of formaldehyde. Sepiolite can be utilized in catalytic reactions for its unique structure, composition and high surface area. The adhesion between sepiolite fibers and the blocked microporous channel (by impurities) demands the activation of natural sepiolite through acid treatment. This treatment successfully produces acid-modified sepiolite Pt-supported samples. The impacts of different acid concentrations, Pt loading content and calcination temperature on catalytic activity for formaldehyde (HCHO) oxidation are studied. The catalytic activity of HCHO is characterized and evaluated by techniques including specific surface area, X-ray diffraction, Fourier transform infrared spectrum, X-ray photoelectron spectroscopy and transmission electron microscopy. The results show the maximum specific area of sepiolite at the optimized 0.06 M acid concentration. Among all the prepared samples, the 0.02Pt/Sep catalyst calcined at 500 °C exhibits the highest catalytic activity for the oxidation of HCHO.

High-efficient mineralization of formaldehyde by three-dimensional "PIZZA"-like bismuth molybdate-titania/diatomite composite

The application of TiO₂-based photocatalysts in air pollution control has attracted much attention thanks to their advantageous green and sustainable performance. However, how to improve the degradation efficiency under visible light is still challenging. Herein, we report a ternary three-dimensional "PIZZA"-like Bi₂MoO₆-TiO₂/diatomite (BTD) composite with high-efficient mineralization and recycling performance towards gaseous formaldehyde (HCHO) under visible light. The high-efficient adsorption-photocatalysis collaborative system with intimate interface combination is successfully established among Bi₂MoO₆ (BMO), TiO₂ and diatomite. The HCHO mineralization rate constant of BTD-1:2 composite is up to around 4.03 times and 2.18 times higher than those of bare BMO and binary Bi₂MoO₆-TiO₂ composite, respectively. It is indicated that the introduction of diatomite increases active sites and plays the vital role in the improvement of photocatalysis. In addition, the photogenerated holes (h⁺) and hydroxyl radical (OH) are proved to be the main active species for HCHO mineralization. Furthermore, there is a competitive adsorption relationship between water (H₂O) molecules and HCHO molecules, and both H₂O molecules and oxygen (O₂) molecules participated in the reaction of HCHO mineralization based on in-situ DRIFTs spectra analysis. Our work would give a new perspective on gaseous HCHO purification.

Highly Active Amino-Fullerene Derivative-Modified TiO2 for Enhancing Formaldehyde Degradation Efficiency under Solar-Light Irradiation

Formaldehyde (HCHO) is a ubiquitous indoor pollutant that seriously endangers human health. The removal of formaldehyde effectively at room temperature has always been a challenging problem. Here, a kind of amino-fullerene derivative (C60-EDA)-modified titanium dioxide (C60-EDA/TiO2) was prepared by one-step hydrothermal method, which could degrade the formaldehyde under solar light irradiation at room temperature with high efficiency and stability. Importantly, the introduction of C60-EDA not only increases the adsorption of the free formaldehyde molecules but also improves the utilization of sunlight and suppresses photoelectron-hole recombination. The experimental results indicated that the C60-EDA/TiO2 nanoparticles exhibit much higher formaldehyde removal efficiency than carboxyl-fullerene-modified TiO2, pristine TiO2 nanoparticles, and almost all other reported formaldehyde catalysts especially in the aspect of the quality of formaldehyde that is treated by catalyst with unit mass (mHCHO/mcatalyst = 40.85 mg/g), and the removal efficiency has kept more than 96% after 12 cycles. Finally, a potential formaldehyde degradation pathway was deduced based on the situ diffuse reflectance infrared Fourier transform spectrometry (DRIFTS) and reaction intermediates. This work provides some indications into the design and fabrication of the catalysts with excellent catalytic performances for HCHO removal at room temperature.

Photocatalytic destruction of volatile aromatic compounds by platinized titanium dioxide in relation to the relative effect of the number of methyl groups on the benzene ring

The photocatalytic destruction (PCD) of volatile organic compounds (VOC) into environmentally benign compounds is one of the most ideal routes for the management of indoor air quality. It is nevertheless not easy to achieve the mineralization of aromatic VOC through PCD technology because of their recalcitrant structures (i.e., conjugated π benzene ring). In this research, the PCD potential against three model aromatic hydrocarbons (i.e., benzene (B), toluene (T), and m-xylene (X): namely, BTX) has been explored using a titanium dioxide (TiO₂) supported platinum (Pt) catalyst after the high-temperature hydrogen (H₂)-based reduction (R) pre-treatment (i.e., Pt/TiO₂-R). The effects of the key process variables (e.g., relative humidity (RH), oxygen (O₂) content, flow rate, VOC concentration, and the co-presence of VOC) on the PCD efficiency and related mechanisms were also assessed in detail. The PCD efficiency is seen to increase with the rise in the increasing number of methyl groups on the benzene ring (in the order of benzene (46.5%), toluene (68.2%), and m-xylene (95.9%)), as the adsorption and activation of the VOC molecule on the photocatalyst surface are promoted by the increased distribution of electrons on the benzene ring. The BTX were oxidated subsequently by the photogenerated reactive oxygen species (ROS), i.e., the hydroxyl radicals (•OH) and superoxide anion radicals (•O₂^-). The overall results of this study are expected to help expand the applicability of photocatalysis towards air quality management by offering detailed insights into the factors and processes governing the photocatalytic decomposition of aromatic VOCs.

Bifunctional zeolites-silver catalyst enabled tandem oxidation of formaldehyde at low temperatures

Bifunctional catalysts with tandem processes have achieved great success in a wide range of important catalytic processes, however, this concept has hardly been applied in the elimination of volatile organic compounds. Herein, we designed a tandem bifunctional Zeolites-Silver catalyst that enormously boosted formaldehyde oxidation at low temperatures, and formaldehyde conversion increased by 50 times (100% versus 2%) at 70 °C compared to that of monofunctional supported silver catalyst. This is enabled by designing a bifunctional catalyst composed of acidic ZSM-5 zeolite and silver component, which provides two types of active sites with complementary functions. Detached acidic ZSM-5 activates formaldehyde to generate gaseous intermediates of methyl formate, which is more easily oxidized by subsequent silver component. We anticipate that the findings here will open up a new avenue for the development of formaldehyde oxidation technologies, and also provide guidance for designing efficient catalysts in a series of oxidation reactions.

Reheat treatment under vacuum induces pre-calcined α-MnO2 with oxygen vacancy as efficient catalysts for toluene oxidation

Engineering α-MnO₂ with abundant oxygen vacancies is efficient to enhance its catalytic activity towards toluene oxidation. A simple and facile method was introduced to fabricate oxygen vacancies on α-MnO₂ surface by reheating the pre-calcined samples under vacuum condition. The reheat treatment especially at 180 °C is beneficial for the formation of oxygen vacancies on α-MnO₂ surface, enhancing the oxidation of toluene. The toluene conversion is up to 100% at 270 °C, which is 30 °C lower than that of α-MnO₂ without reheat treatment. The apparent activation energy (16.8 kJ mol^-1) of MnO₂-180 catalyst is lowest among these catalysts, which is essential for accelerating the oxidation of toluene. In-situ DRIFTS results indicate that the MnO₂-180 sample promotes the formation of benzaldehyde and the occurrence of ring-opening reaction, thus effectively improving the catalytic performance for toluene oxidation. A possible catalytic oxidation mechanism of toluene over α-MnO₂ catalysts after reheat treatment was proposed.

Synergy of surface sodium and hydroxyl on NaTi2HO5 nanotubes accelerating the Pt-dominated ambient HCHO oxidation

Surface hydroxyl is widely perceived as conducive to HCHO degradation. Here, a kind of sodium titanate with interlayered hydroxyls (NaTi₂HO₅) was prepared to study the action conditions of surface hydroxyls in HCHO oxidation. The nanotubes mainly exposing (001) and nanobelts mainly exposing (100) are synthesized as the two morphologies of NaTi₂HO₅. We found the (001) facet is much more favored to HCHO adsorption via HRTEM and XPS analysis. The DFT calculations prove that the synergy of surface hydroxyl and Na atom is perfect for HCHO chemisorption. By this means NaTi₂HO₅ nanotubes can partially oxidize HCHO into formate and release very few CO, measured by in situ DRIFTS. Dominated by Pt nanoparticles, the complete oxidation of HCHO can be performed on NaTi₂HO₅ nanotubes with enhanced early reaction speed. Rather than simple surface hydroxyl, the effective synergy of hydroxyl and positive ion is proposed as an advantage for HCHO oxidation.

One-step fabrication of electrospun flexible and hierarchically porous Pt/γ-Al2O3 nanofiber membranes for HCHO and particulate removal

A flexible Pt/γ-Al2O3 nanofiber membrane with optimal 2 wt% Pt content can effectively decompose HCHO into CO2 at room temperature.

Photocatalytic Air Purification Using Functional Polymeric Carbon Nitrides

The techniques for the production of the environment have received attention because of the increasing air pollution, which results in a negative impact on the living environment of mankind. Over the decades, burgeoning interest in polymeric carbon nitride (PCN) based photocatalysts for heterogeneous catalysis of air pollutants has been witnessed, which is improved by harvesting visible light, layered/defective structures, functional groups, suitable/adjustable band positions, and existing Lewis basic sites. PCN-based photocatalytic air purification can reduce the negative impacts of the emission of air pollutants and convert the undesirable and harmful materials into value-added or nontoxic, or low-toxic chemicals. However, based on previous reports, the systematic summary and analysis of PCN-based photocatalysts in the catalytic elimination of air pollutants have not been reported. The research progress of functional PCN-based composite materials as photocatalysts for the removal of air pollutants is reviewed here. The working mechanisms of each enhancement modification are elucidated and discussed on structures (nanostructure, molecular structue, and composite) regarding their effects on light-absorption/utilization, reactant adsorption, intermediate/product desorption, charge kinetics, and reactive oxygen species production. Perspectives related to further challenges and directions as well as design strategies of PCN-based photocatalysts in the heterogeneous catalysis of air pollutants are also provided.

Fast organic degradation on Ti- and Bi-based photocatalysts via co-deposited Pt and Ni3(PO4)2 nanoparticles

Environmental remediation via semiconductor (SC) photocatalysis has attracted great attention over the past three decades. However, prospect for large scale application is still under debate, basically due to the bottleneck of fast charge recombination and/or slow surface reaction. Herein we report a universal solution of speeding up organic degradation simply via co-deposited Pt and nickel phosphate (NiP). Several representative SCs have been examined, including TiO₂ (anatase, rutile, and brookite) under a 320 nm light, and Bi-based SC (BiVO₄, Bi₂WO₆, and Bi₂MoO₆) under a 420 nm light. In all cases, the rates of phenol degradation in aqueous solution always varied not only in the order of NiP/Pt/SC > Pt/SC > NiP/SC > SC, but also NiP/Pt/SC > (Pt/SC + NiP/SC + SC). Meanwhile, hydroquinone and benzoquinone were produced as the main intermediates, but their concentration was much lower than that of phenol decreased, especially for NiP-containing sample. The solid was characterized with several techniques, including photoluminescence and (photo)electrochemical measurement. It is proposed that Pt and NiP act as co-catalysts for O₂ reduction and phenol oxidation, respectively. Such electron and hole transfer promote each other, additionally improving the efficiency of charge separation, and further increasing the rates of surface reactions. This work highlights the necessity of a versatile co-catalyst in SC photocatalysis.

Insoluble matrix proteins from shell waste for synthesis of visible-light response photocatalyst to mineralize indoor gaseous formaldehyde

HCHO is the most concerned indoor air pollutant that photocatalytic degradation is a feasible approach. To achieve efficient and complete degradation of HCHO under visible light irradiation, heteroatoms are usually doped in TiO₂. But using natural materials as a dopant instead of expensive and toxic chemicals to fertilize TiO₂ remains challenging. This paper proposes a sustainable and green approach to synthesize an efficient N, Ca co-doped TiO₂ photocatalyst (TIMP) by using the insoluble matrix proteins (IMPs) extracted from abalone shell. TIMP-0.8 achieves near completely degradation HCHO within 45 min under visible light at ambient temperature and exhibits superior stability after 7 cycles. TIMP-0.8 has monodispersity with smaller diameter, high porosity, abundant defects and high adsorption affinity for surface hydroxyls compared with pure TiO₂. With the assistance of IMPs, the rate-determining step of HCHO degradation changes from -COOH oxidation to spontaneous decomposition of HCO₃^-, significantly facilitating the elimination and mineralization of HCHO. Overall, IMPs from abalone shell are natural surfactant, bio-templet, and dopant for TiO₂ modification, contributing to desirable visible-light photocatalytic performance for HCHO degradation. This paper provides new insight for high-value utilization of waste shell and photocatalytic indoor purification.

One Pot Synthesis, Surface and Magnetic Properties of Cu2O/Cu and Cu2O/CuO Nanocomposites

A series of copper-based systems containing two different nanocomposites (Cu2O/CuO and Cu2O/Cu) was synthesized by the egg white assisted auto-combustion route. This method was distinguished by the simplicity of its steps, low cost, one-pot synthesis process at low temperature and, short time. The characterization of the as prepared nanocomposites was carried out by using X-ray diffraction (XRD), Fourier-transform infrared (FTIR), Scanning electron microscope (SEM) and transmission electron micrograph (TEM), Energy dispersive spectrometry (EDS) techniques. Surface and magnetic properties of the obtained systems were determined by using N2 adsorption/desorption isotherms at 77 K and the vibrating sample magnetometer (VSM) technique. XRD results confirmed the formation of Cu2O/CuO and Cu2O/Cu nanocomposites with different ratios of well crystalline CuO, Cu2O, and Cu phases. FTIR results of the combusted product displays the presence of both CuO and Cu2O, respectively. SEM/EDS and TEM results confirm the formation of a porous nanocomposite containing Cu, O, and C elements. The change in concentration of the oxygen vacancies at the surface or interface of both Cu2O/CuO and Cu2O/Cu nanoparticles resulted in different changes in their magnetization. Based on this study, it is possible to obtain nanocomposite-based copper with multiple valances by a simple and inexpensive route which can be suitable for the fabrication of different transition metal composites.

Fabrication of Cu1.5Mn1.5O4 Nanoparticles Using One Step Self-Assembling Route to Enhance Energy Consumption

The preparation of copper manganite (hopcalite, Cu1.5Mn1.5O4), as a single phase, was achieved by using a sustainable method of green synthesis. This method is based on the replacement of the conventional “brute force” ceramic preparation by the recent “soft force” green synthesis via the egg white assisted one-step method. In other words, we present a facile and rapid methodology to prepare the nanocrystalline Cu1.5Mn1.5O4 spinel as a single phase, compared to our previous work using ceramic and glycine-assisted combustion methods. The as-synthesized copper manganite was characterized using X-ray diffraction (XRD), Fourier-transform infrared (FTIR), energy-dispersive spectroscopy (EDS), and scanning electron microscope (SEM). We used a vibrating sample magnetometer to determine the magnetic properties of the prepared sample (VSM). XRD, FTIR, SEM, EDS and transmittance electron micrograph (TEM) resulted in synthesis of a successful cubic spinel Cu1.5Mn1.5O4 system with a sponge crystal structure. The particles of the prepared materials are polycrystalline in their nature and the sizes ranged between 50 and 100 nm. The magnetic measurement demonstrated that the generated nanostructure has been found to exhibit ferromagnetism at room temperature with an optimum saturation magnetization value (0.2944 emu/g).

Highly efficient Ru/CeO2 catalysts for formaldehyde oxidation at low temperature and the mechanistic study

Ru species have a high redox capacity on a CeO₂ support, and the metallic Ru species could be easily oxidized back to RuO_x species.

Hierarchical nanostructures self-assembled from δ-MnO2 ultrathin nanosheets and Mn3O4 octahedrons for efficient room-temperature HCHO oxidation

Self-assembling ultrathin active δ-MnO₂ nanosheets and Mn₃O₄ octahedrons into hierarchical texture enhances room-temperature formaldehyde oxidation at a low-level of Pt.

Selective photocatalytic oxidation of 3-pyridinemethanol on platinized acid/base modified TiO2

TEM micrographs of selected platinized samples.

Reverse water-gas shift reaction over Pt/MoOx/TiO2: reverse Mars–van Krevelen mechanism via redox of supported MoOx

Pt/MoO_x/TiO₂ shows excellent catalytic performance for the reverse water-gas shift reaction at 250 °C via reverse Mars–van Krevelen mechanism.

Abatement of formaldehyde with photocatalytic and catalytic oxidation: a review

Formaldehyde is one of the vital chemicals produced by industries, transports, and domestic products. Formaldehyde emissions adversely affect human health and it is well known for causing irritation and nasal tumors. The major aim of the modern indoor formaldehyde control study is in view of energy capacity, product selectivity, security, and durability for efficient removal of formaldehyde. The two important methods to control this harmful chemical in the indoor environments are photocatalytic oxidation and catalytic oxidation with noble metals and transition metal oxides. By harmonizing different traditional photocatalytic and catalytic oxidation technologies that have been evolved already, here we give a review of previously developed efforts to degrade indoor formaldehyde. The major concern in this article is based on getting the degradation of formaldehyde at ambient temperature. In this article, different aspects of these two methods with their merits and demerits are discussed. The possible effects of operating parameters like preparation methods, support, the effect of light intensity in photocatalytic oxidation, relative humidity, etc. have been discussed comprehensively.

From platinum atoms in molecules to colloidal nanoparticles: A review on reduction, nucleation and growth mechanisms

Platinum (Pt) is one of the most studied materials in catalysis today and considered for a wide range of applications: chemical synthesis, energy conversion, air treatment, water purification, sensing, medicine etc. As a limited and non-renewable resource, optimized used of Pt is key. Nanomaterial design offers multiple opportunities to make the most of Pt resources down to the atomic scale. In particular, colloidal syntheses of Pt nanoparticles are well documented and simple to implement, which accounts for the large interest in research and development. For further breakthroughs in the design of Pt nanomaterials, a deeper understanding of the intricate synthesis-structures-properties relations of Pt nanoparticles must be obtained. Understanding how Pt nanoparticles form from molecular precursors is both a challenging and rewarding area of investigation. It is directly relevant to develop improved Pt nanomaterials but is also a source of inspiration to design other precious metal nanostructures. Here, we review the current understanding of Pt nanoparticle formation. This review is aimed at readers with interest in Pt nanoparticles in general and their colloidal syntheses in particular. Readers with a strongest interest on the study of nanomaterial formation will find here the case study of Pt. The preferred model systems and characterization techniques used to perform the study of Pt nanoparticle syntheses are discussed. In light of recent achievements, further direction and areas of research are proposed.