Incorporation of Antifreeze Proteins into Polymer Coatings Using Site-Selective Bioconjugation

Anti-freezing hydrogel regulated by ice-structuring proteins/cellulose nanofibers system as flexible sensor for winter sports

Conductive hydrogels are widely used as sensors in wearable devices. However, hydrogels cannot endure harsh low-temperature environments. Herein, a new regulatory system based on natural ice-structuring proteins (ISPs) and cellulose nanofibers (CNFs) is introduced into hydrogel network consisting of chemically crosslinked network of copolymerized acrylamide and 2-acrylamide-2-methylpropanesulfonic acid, and physically crosslinked polyvinyl alcohol chains, affording an anti-freezing hydrogel with high conductivity (2.63 S/m). These hydrogels show excellent adhesion behavior to various matrices (including aluminum, glass, pigskin, and plastic). Their mechanical properties are significantly improved with the increase in CNF content (tensile strength of 106.4 kPa, elastic modulus of 133.8 kPa). In addition, ISPs inhibit the growth of ice. This endows the hydrogels with anti-freezing property and allows them to maintain satisfactory mechanical properties, conductivity and sensing properties below zero degrees. Moreover, this hydrogel shows high sensitivity to tensile and compressive deformation (GF = 5.07 at 600-800 % strain). Therefore, it can be utilized to develop strain-type pressure sensors that can be attached directly to human skin for detecting various body motions accurately, reliably, and stably. This study proposes a simple strategy to improve the anti-freezing property of hydrogels, which provides new insights for developing flexible hydrogel electronic devices for application in winter sports.

Generating Ice-Binding Protein-Polymer Bioconjugates

Protein-polymer conjugates combine the stability of polymers with the diversity, specificity, and functionality of proteins. The resulting hybrid materials can display properties not found in the individual components and can be particularly relevant for engineering new functionalities. Ice-binding proteins have many potential biotechnical and biomedical applications. However, their widespread use has been limited due to cost of production, limited activity, and relative instability. Polymer attachment has led to higher thermal hysteresis activities with less protein and superior stabilities. Thus, IBP-polymer conjugates have the ability to overcome a number of these challenges and lead to materials to tackle biomedical applications.

On the Durability of Icephobic Coatings: A Review

Ice formation and accumulation on surfaces has a negative impact in many different sectors and can even represent a potential danger. In this review, the latest advances and trends in icephobic coatings focusing on the importance of their durability are discussed, in an attempt to pave the roadmap from the lab to engineering applications. An icephobic material is expected to lower the ice adhesion strength, delay freezing time or temperature, promote the bouncing of a supercooled drop at subzero temperatures and/or reduce the ice accretion rate. To better understand what is more important for specific icing conditions, the different types of ice that can be formed in nature are summarized. Similarly, the alternative methods to evaluate the durability are reviewed, as this is key to properly selecting the method and parameters to ensure the coating is durable enough for a given application. Finally, the different types of icephobic surfaces available to date are considered, highlighting the strategies to enhance their durability, as this is the factor limiting the commercial applicability of icephobic coatings.

Inhibition of Defect-Induced Ice Nucleation, Propagation, and Adhesion by Bioinspired Self-Healing Anti-Icing Coatings

Anti-icing coatings on outdoor infrastructures inevitably suffer from mechanical injuries in numerous icing scenarios such as hailstorms, sandstorms, impacts of foreign objects, and icing-deicing cycles. Herein, the mechanisms of surface-defect-induced icing are clarified. At the defects, water molecules exhibit stronger adsorption and the heat transfer rate increases, accelerating the condensation of water vapor as well as ice nucleation and propagation. Moreover, the ice-defect interlocking structure increases the ice adhesion strength. Thus, a self-healing (at -20 °C) antifreeze-protein (AFP)-inspired anti-icing coating is developed. The coating is based on a design that mimics the ice-binding and non-ice-binding sites in AFPs. It enables the coating to markedly inhibit ice nucleation (nucleation temperature < -29.4 °C), prevent ice propagation (propagation rate < 0.00048 cm²/s), and reduce ice adhesion on the surface (adhesion strength < 38.9 kPa). More importantly, the coating can also autonomously self-heal at -20 °C, as a result of multiple dynamic bonds in its structure, to inhibit defect-induced icing processes. The healed coating sustains high anti-icing and deicing performance even under various extreme conditions. This work reveals the in-depth mechanism of defect-induced ice formation as well as adhesion, and proposes a self-healing anti-icing coating for outdoor infrastructures.

Recent advances of bio-inspired anti-icing surfaces

The need for improved anti-icing surfaces is the demand of the time and closely related to many important aspects of our lives as surface icing threatens not only industrial production but also human safety. Freezing on a cold surface is usually a heterogeneous nucleation process induced by the substrate. Creating an anti-icing surface is mainly achieved by changing surface morphology and chemistry to regulate the interaction between the surface and the water/ice to inhibit freezing on the surface. In this paper, recent research progress in the creation of biomimetic anti-icing surfaces is reviewed. Firstly, basic strategies of bionic anti-icing are introduced, and then bionic anti-icing surface strategies are reviewed according to four aspects: the process of ice formation, including condensate self-removing, inhibiting ice nucleation, reducing ice adhesion, and melting accumulated ice on the surface. The remaining challenges and the direction of future development of biomimetic anti-icing surfaces are also discussed.

Antifreeze Proteins: A Tale of Evolution From Origin to Energy Applications

Icing and formation of ice crystals is a major obstacle against applications ranging from energy systems to transportation and aviation. Icing not only introduces excess thermal resistance, but it also reduces the safety in operating systems. Many organisms living under harsh climate and subzero temperature conditions have developed extraordinary survival strategies to avoid or delay ice crystal formation. There are several types of antifreeze glycoproteins with ice-binding ability to hamper ice growth, ice nucleation, and recrystallization. Scientists adopted similar approaches to utilize a new generation of engineered antifreeze and ice-binding proteins as bio cryoprotective agents for preservation and industrial applications. There are numerous types of antifreeze proteins (AFPs) categorized according to their structures and functions. The main challenge in employing such biomolecules on industrial surfaces is the stabilization/coating with high efficiency. In this review, we discuss various classes of antifreeze proteins. Our particular focus is on the elaboration of potential industrial applications of anti-freeze polypeptides.

Kinetic Inhibition of Clathrate Hydrate by Copolymers Based on N-Vinylcaprolactam and N-Acryloylpyrrolidine: Optimization Effect of Interfacial Nonfreezable Water of Polymers

Amphiphilic polymers have now been designed to achieve an icephobic performance and have been used for ice adhesion prevention. They may function by forming a strongly bonded but nonfreezable water shell which serves as a self-lubricating interfacial layer that weakens the adhesion strength between ice and the surface. Here, an analogous concept is built to prevent the formation of clathrate hydrate compounds during oil and natural gas production, in which amphiphilic water-soluble polymers act as efficient kinetic hydrate inhibitors (KHIs). A novel group of copolymers with N-vinylcaprolactam and N-acryloylpyrrolidine structural units are investigated in this study. The relationships among the amphiphilicity, lower critical solution temperature, nonfreezable bound water, and kinetic hydrate inhibition time are analyzed in terms of the copolymer compositions. Low-field NMR relaxometry revealed the crucial interfacial water in tightly bound dynamic states which led to crystal growth rates changing with the copolymer compositions, in accord with the rotational rheometric analysis results. The nonfreezable bound water layer confirmed by a calorimetry analysis also changes with the polymer amphiphilicity. Therefore, in the interface between the KHI polymers and hydrate, water surrounding the polymers plays a critical role by helping to delay the nucleation and growth of embryonic ice/hydrates. Appropriate amphiphilicity of the copolymers can achieve the optimal interfacial properties for slowing down hydrate crystal growth.

Beetle and mussel-inspired chimeric protein for fabricating anti-icing coating

Ice accretion on surfaces can cause serious damages and economic losses in industries and civilian facilities. Antifreeze proteins (AFPs) as evolutionary adaptation products of organisms to cold climates, provide solutions for alleviating icing problems. In this work, a chimeric protein Mfp-AFP was rationally designed combining mussel-inspired adhesive domain with Tenebrio molitor-derived antifreeze protein domain. Expectedly, the multifunctional Mfp-AFP can lower the freezing point of water and inhibit ice recrystallization. The chimeric protein could also readily modify diverse solid surfaces due to the adhesive domain containing Dopa, and resist frosting and delay ice formation due to the beetle-derived antifreeze fragment. Moreover, Mfp-AFP coatings display excellent biocompatibility proved by cytocompatibility and hemolysis assays. Here, the designed multifunctional protein coatings provide an alternative strategy for fabricating anti-icing surfaces.

Anti freeze proteins (Afp): Properties, sources and applications - A review

Extreme cold marine and freshwater temperatures (below 4 °C) induce massive deterioration to the cell membranes of organisms resulting in the formation of ice crystals, consequently causing organelle damage or cell death. One of the adaptive mechanisms organisms have evolved to thrive in cold environments is the production of antifreeze proteins with the functional capabilities to withstand frigid temperatures. Antifreeze proteins are extensively identified in different cold-tolerant species and they facilitate the persistence of cold-adapted organisms by decreasing the freezing point of their body fluids. Various structurally diverse types of antifreeze proteins detected possess the ability to modify ice crystal growth by thermal hysteresis and ice recrystallization inhibition. The unique properties of antifreeze proteins have made them a promising resource in industry, biomedicine, food storage and cryobiology. This review collates the findings of the various studies carried out in the past and the recent developments observed in the properties, functional mechanisms, classification, distinct sources and the ever-increasing applications of antifreeze proteins. This review also summarizes the possibilities of the way forward to identify new avenues of research on anti-freeze proteins.

Low-temperature adaptive conductive hydrogel based on ice structuring proteins/CaCl2 anti-freeze system as wearable strain and temperature sensor

Conductive hydrogels as wearable devices meet the basic demands of mechanical flexibility and smart sensing. However, achieving anti-freeze property in conductive hydrogels is still challengeable. Here, a novel anti-freezing system based on ice structuring proteins and CaCl₂ was introduced to enable a conductive hydrogel with low-temperature adaptability. Both formation of ice nuclei and ice growth of the hydrogel at sub-zero temperature could be inhibited. Supported by the anti-freeze system, the hydrogel revealed good flexibility (890% at -20 °C), recovery and conductivity (0.50 S/m at -20 °C) at both room temperature and sub-zero temperature. The low-temperature adaptability enabled the hydrogel to be used as strain and temperature sensors at both room temperature and sub-zero temperature. The anti-freeze system in this work is expected to open up a new avenue to promote the conductive hydrogel with low-temperature adaptability.

Design and applications of surfaces that control the accretion of matter

Surfaces that provide control over liquid, solid, or vapor accretion provide an evolutionary advantage to numerous plants, insects, and animals. Synthetic surfaces inspired by these natural surfaces can have a substantial impact on diverse commercial applications. Engineered liquid and solid repellent surfaces are often designed to impart control over a single state of matter, phase, or fouling length scale. However, surfaces used in diverse real-world applications need to effectively control the accrual of matter across multiple phases and fouling length scales. We discuss the surface design strategies aimed at controlling the accretion of different states of matter, particularly those that work across multiple length scales and different foulants. We also highlight notable applications, as well as challenges associated with these designer surfaces' scale-up and commercialization.

Advanced Nanomaterials-Assisted Cell Cryopreservation: A Mini Review

Cell cryopreservation is of vital significance both for transporting and storing cells before experimental/clinical use. Cryoprotectants (CPAs) are necessary additives in the preserving medium in cryopreservation, preventing cells from freeze-thaw injuries. Traditional organic solvents have been widely used in cell cryopreservation for decades. Given the obvious damage to cells due to their undesirable cytotoxicity and the burdensome post-thaw washing cycles before use, traditional CPAs are more and more likely to be replaced by modern ones with lower toxicity, less processing, and higher efficiency. As materials science thrives, nanomaterials are emerging to serve as potent vehicles for delivering nontoxic CPAs or inherent CPAs comparable to or even superior to conventional ones. This review will introduce some advanced nanomaterials (e.g., organic/inorganic nanoCPAs, nanodelivery systems) utilized for cell cryopreservation, providing broader insights into this developing field.

Ice Inhibition for Cryopreservation: Materials, Strategies, and Challenges

Cryopreservation technology has developed into a fundamental and important supporting method for biomedical applications such as cell-based therapeutics, tissue engineering, assisted reproduction, and vaccine storage. The formation, growth, and recrystallization of ice crystals are the major limitations in cell/tissue/organ cryopreservation, and cause fatal cryoinjury to cryopreserved biological samples. Flourishing anti-icing materials and strategies can effectively regulate and suppress ice crystals, thus reducing ice damage and promoting cryopreservation efficiency. This review first describes the basic ice cryodamage mechanisms in the cryopreservation process. The recent development of chemical ice-inhibition molecules, including cryoprotectant, antifreeze protein, synthetic polymer, nanomaterial, and hydrogel, and their applications in cryopreservation are summarized. The advanced engineering strategies, including trehalose delivery, cell encapsulation, and bioinspired structure design for ice inhibition, are further discussed. Furthermore, external physical field technologies used for inhibiting ice crystals in both the cooling and thawing processes are systematically reviewed. Finally, the current challenges and future perspectives in the field of ice inhibition for high-efficiency cryopreservation are proposed.

Pyridine-2,6-dicarboxaldehyde-Enabled N-Terminal In Situ Growth of Polymer-Interferon α Conjugates with Significantly Improved Pharmacokinetics and In Vivo Bioactivity

Polymer-protein conjugates are a class of biohybrids with unique properties that are highly useful in biomedicine ranging from protein therapeutics to biomedical imaging; however, it remains a considerable challenge to conjugate polymers to proteins in a site-specific, mild, and efficient way to form polymer-protein conjugates with uniform structures and properties and optimal functions. Herein we report pyridine-2,6-dicarboxaldehyde (PDA)-enabled N-terminal modification of proteins with polymerization initiators for in situ growth of poly(oligo(ethylene glycol)methyl ether methacrylate) (POEGMA) conjugates uniquely at the N-termini of a range of natural and recombinant proteins in a mild and efficient fashion. The formed POEGMA-protein conjugates showed highly retained in vitro bioactivity as compared with free proteins. Notably, the in vitro bioactivity of a POEGMA-interferon α (IFN) conjugate synthesized by this new chemistry is 8.1-fold higher than that of PEGASYS that is a commercially available and Food and Drug Administration (FDA) approved PEGylated IFN. The circulation half-life of the conjugate is similar to that of PEGASYS but is 46.2 times longer than that of free IFN. Consequently, the conjugate exhibits considerably improved antiviral bioactivity over free IFN and even PEGASYS in a mouse model. These results indicate that the PDA-enabled N-terminal grafting-from method is applicable to a number of proteins whose active sites are far away from the N-terminus for the synthesis of N-terminal polymer-protein conjugates with high yield, well-retained activity, and considerably improved pharmacology for biomedical applications.

The Inhibition of Icing and Frosting on Glass Surfaces by the Coating of Polyethylene Glycol and Polypeptide Mimicking Antifreeze Protein

The development of anti-icing, anti-frosting transparent plates is important for many reasons, such as poor visibility through the ice-covered windshields of vehicles. We have fabricated new glass surfaces coated with polypeptides which mimic a part of winter flounder antifreeze protein. We adopted glutaraldehyde and polyethylene glycol as linkers between these polypeptides and silane coupling agents applied to the glass surfaces. We have measured the contact angle, the temperature of water droplets on the cooling surfaces, and the frost weight. In addition, we have conducted surface roughness observation and surface elemental analysis. It was found that peaks in the height profile, obtained with the atomic force microscope for the polypeptide-coated surface with polyethylene glycol, were much higher than those for the surface without the polypeptide. This shows the adhesion of many polypeptide aggregates to the polyethylene glycol locally. The average supercooling temperature of the droplet for the polypeptide-coated surface with the polyethylene glycol was lower than for the polypeptide-coated surface with glutaraldehyde and the polyethylene-glycol-coated surface without the polypeptide. In addition, the average weight of frost cover on the specimen was lowest for the polypeptide-coated surface with the polyethylene glycol. These results argue for the effects of combined polyethylene glycol and polypeptide aggregates on the locations of ice nuclei and condensation droplets. Thus, this polypeptide-coating with the polyethylene glycol is a potential contender to improve the anti-icing and anti-frosting of glasses.

Site-specific conjugation of antifreeze proteins onto polymer-stabilized nanoparticles

Antifreeze proteins (AFPs) have many potential applications, ranging from cryobiology to aerospace, if they can be incorporated into materials. Here, a range of engineered AFP mutants were prepared and site-specifically conjugated onto RAFT polymer-stabilized gold nanoparticles to generate new hybrid multivalent ice growth inhibitors. Only the SNAP-tagged AFPs lead to potent 'antifreeze' active nanomaterials with His-Tag capture resulting in no activity, showing the mode of conjugation is essential. This versatile strategy will enable the development of multivalent AFPs for translational and fundamental studies.

Heterogeneous ice nucleation correlates with bulk-like interfacial water

Establishing a direct correlation between interfacial water and heterogeneous ice nucleation (HIN) is essential for understanding the mechanism of ice nucleation. Here, we study the HIN efficiency on polyvinyl alcohol (PVA) surfaces with different densities of hydroxyl groups. We find that the HIN efficiency increases with the decreasing hydroxyl group density. By explicitly considering that interfacial water molecules of PVA films consist of "tightly bound water," "bound water," and "bulk-like water," we reveal that bulk-like water can be correlated directly to the HIN efficiency of surfaces. As the density of hydroxyl groups decreases, bulk-like water molecules can rearrange themselves with a reduced energy barrier into ice due to the diminishing constraint by the hydroxyl groups on the PVA surface. Our study not only provides a new strategy for experimentally controlling the HIN efficiency but also gives another perspective in understanding the mechanism of ice nucleation.

Design of surfaces for controlling hard and soft fouling

In this review, we present a framework to guide the design of surfaces which are resistant to solid fouling, based on the modulus and length scale of the fouling material. Solid fouling is defined as the undesired attachment of solid contaminants including ice, clathrates, waxes, inorganic scale, polymers, proteins, dust and biological materials. We first provide an overview of the surface design approaches typically applied across the scope of solid fouling and explain how these disparate research efforts can be united to an extent under a single framework. We discuss how the elastic modulus and the operating length scale of a foulant determine its ability or inability to elastically deform surfaces. When surface deformation occurs, minimization of the substrate elastic modulus is critical for the facile de-bonding of a solid contaminant. Foulants with low modulus or small deposition sizes cannot deform an elastic bulk material and instead de-bond more readily from surfaces with chemistries that minimize their interfacial free energy or induce a particular repellant interaction with the foulant. Overall, we review reported surface design strategies for the reduction in solid fouling, and provide perspective regarding how our framework, together with the modulus and length scale of a foulant, can guide future antifouling surface designs. This article is part of the theme issue 'Bioinspired materials and surfaces for green science and technology'.

Icephobic Strategies and Materials with Superwettability: Design Principles and Mechanism

Ice formation and accretion on surfaces is a serious economic issue in energy supply and transportation. Recent strategies for developing icephobic surfaces are intimately associated with superwettability. Commonly, the superwettability of icephobic materials depends on their surface roughness and chemical composition. This article critically categorizes the possible strategies to mitigate icing problems from daily life. The wettability and classical nucleation theories are used to characterize the icephobic surfaces. Thermodynamically, the advantages/disadvantages of superhydrophobic surfaces are discussed to explain icephobic behavior. The importance of elasticity, slippery liquid-infused porous surfaces (SLIPSs), amphiphilicity, antifreezing protein, organogels, and stimuli-responsive materials has been highlighted to induce icephobic performance. In addition, the design principles and mechanism to fabricate icephobic surfaces with superwettability are explored and summarized.

Suppression of droplets freezing on glass surfaces on which antifreeze polypeptides are adhered by a silane coupling agent

The development of ice-phobic, glass-substrate surfaces is important for many reasons such as poor visibility through the ice-covered windshields of vehicles. The present authors have developed new glass surfaces coated with a silane coupling agent and polypeptides whose amino-acid sequence is identical to a partial sequence of winter flounder antifreeze protein. We have conducted experiments on the freezing of sessile water droplets on the glass surfaces, and measured the droplet temperature, contact angle, contact area and surface roughness. The results show that the supercooling temperature decreased noticeably in the case where a higher concentration solution of polypeptide was used for the coating. The adhesion strength of frozen droplets was lowest in the same case. In addition, we observed many nanoscale humps on the coated surface, which were formed by polypeptide aggregates in the solution. We argue that the combination of the hydrophilic humps and the hydrophobic base surfaces causes water molecules adjacent to the surfaces to have a variety of orientations in that plane, even after the ice layer started to grow. This then induces a misfit of water-molecule spacing in the ice layers and consequent formation of fragile polycrystalline structure. This explains the lower values of ice adhesion strength and supercooling enhancement in the cases of the polypeptide-coated glass plates.

Photothermal trap utilizing solar illumination for ice mitigation

Ice buildup is an operational and safety hazard in wind turbines, power lines, and airplanes. Traditional deicing methods, including mechanical and chemical means, are energy-intensive or environmentally unfriendly. Superhydrophobic anti-icing surfaces, while promising, can become ineffective due to frost formation within textures. We report on a "photothermal trap"-a laminate applied to a base substrate-that can efficiently deice by converting solar illumination to heat at the ice-substrate interface. It relies on the complementing properties of three layers: a selective absorber for solar radiation, a thermal spreader for lateral dispersal of heat, and insulation to minimize transverse heat loss. Upon illumination, thermal confinement at the heat spreader leads to rapid increase of the surface temperature, thereby forming a thin lubricating melt layer that facilitates ice removal. Lateral heat spreading overcomes the unavoidable shadowing of certain areas from direct illumination. We provide a design map that captures the key physics guiding illumination-induced ice removal. We demonstrate the deicing performance of the photothermal trap at very low temperatures, and under frost and snow coverage, via laboratory-scale and outdoor experiments.

Falling water ice affinity purification of ice-binding proteins

Ice-binding proteins (IBPs) permit their hosts to thrive in the presence of ice. The ability of IBPs to control ice growth makes them potential additives in industries ranging from food storage and cryopreservation to anti-icing systems. For IBPs to be used in commercial applications, however, methods are needed to produce sufficient quantities of high-quality proteins. Here, we describe a new method for IBP purification, termed falling water ice affinity purification (FWIP). The method is based on the affinity of IBPs for ice and does not require molecular tags. A crude IBP solution is allowed to flow over a chilled vertical surface of a commercial ice machine. The temperature of the surface is lowered gradually until ice crystals are produced, to which the IBPs bind but other solutes do not. We found that a maximum of 35 mg of IBP was incorporated in 1 kg of ice. Two rounds of FWIP resulted in >95% purity. An ice machine that produces 60 kg of ice per day can be used to purify one gram of IBP per day. In combination with efficient concentration of the protein solution by tangential flow filtration the FWIP method is suitable for the purification of grams of IBPs for research purposes and applications.

Bioinspired Materials for Controlling Ice Nucleation, Growth, and Recrystallization

Ice formation, mainly consisting of ice nucleation, ice growth, and ice recrystallization, is ubiquitous and crucial in wide-ranging fields from cryobiology to atmospheric physics. Despite active research for more than a century, the mechanism of ice formation is still far from satisfactory. Meanwhile, nature has unique ways of controlling ice formation and can provide resourceful avenues to unravel the mechanism of ice formation. For instance, antifreeze proteins (AFPs) protect living organisms from freezing damage via controlling ice formation, for example, tuning ice nucleation, shaping ice crystals, and inhibiting ice growth and recrystallization. In addition, AFP mimics can have applications in cryopreservation of cells, tissues, and organs, food storage, and anti-icing materials. Therefore, continuous efforts have been made to understand the mechanism of AFPs and design AFP inspired materials. In this Account, we first review our recent research progress in understanding the mechanism of AFPs in controlling ice formation. A Janus effect of AFPs on ice nucleation was discovered, which was achieved via selectively tethering the ice-binding face (IBF) or the non-ice-binding face (NIBF) of AFPs to solid surfaces and investigating specifically the effect of the other face on ice nucleation. Through molecular dynamics (MD) simulation analysis, we observed ordered hexagonal ice-like water structure atop the IBF and disordered water structure atop the NIBF. Therefore, we conclude that the interfacial water plays a critical role in controlling ice formation. Next, we discuss the design and fabrication of AFP mimics with capabilities in tuning ice nucleation and controlling ice shape and growth, as well as inhibiting ice recrystallization. For example, we tuned ice nucleation via modifying solid surfaces with supercharged unfolded polypeptides (SUPs) and polyelectrolyte brushes (PBs) with different counterions. We found graphene oxide (GO) and oxidized quasi-carbon nitride quantum dots (OQCNs) had profound effects in controlling ice shape and inhibiting ice growth. We also studied the ion-specific effect on ice recrystallization inhibition (IRI) with a large variety of anions and cations. All functionalities are achieved by tuning the properties of interfacial water on these materials, which reinforces the importance of the interfacial water in controlling ice formation. Finally, we review the development of novel application-oriented materials emerging from our enhanced understanding of ice formation, for example, ultralow ice adhesion coatings with aqueous lubricating layer, cryopreservation of cells by inhibiting ice recrystallization, and two-dimensional (2D) and three-dimensional (3D) porous materials with tunable pore sizes through recrystallized ice crystal templates. This Account sheds new light on the molecular mechanism of ice formation and will inspire the design of unprecedented functional materials based on controlled ice formation.

Fabrication of Anti-Icing Surfaces by Short α-Helical Peptides

We designed 12-amino acid peptides as antifreeze protein (AFP) mimetics and tuned the antifreeze activity of the peptides by their structures. Moreover, these short peptides were first immobilized to surfaces as an anti-icing coating. We discovered that the peptides with higher antifreeze activity exhibited better anti-icing performance. It is the first time that short peptides were successfully applied to fabricate anti-icing surfaces, which is certainly advantageous in comparison to the AFP anti-icing coatings previously reported.

Inhibition of Heterogeneous Ice Nucleation by Bioinspired Coatings of Polyampholytes

Control of heterogeneous ice nucleation (HIN) on foreign surfaces is of great importance for anti-ice-nucleation material design. In this work, we studied the HIN behaviors on various ion-modified poly(butylene succinate) (PBS) surfaces via chain-extension reaction. Inspired by antifreeze proteins (AFPs), the PBS-based polyampholytes, containing both negative and positive charge groups on a single chain, show excellent performance of ice nucleation inhibition and freezing delay. Unlike the extremely high price and low availability of AFPs, these PBS-based polyampholytes can be commercially synthesized under mild reaction conditions. Through water freezing tests on a wide range of substrates at different temperatures, these PBS-based polyampholytes have shown application value of tuning ice nucleation via a simple spin-coating method.

Inhibition of Tetrahydrofuran Hydrate Formation in the Presence of Polyol-Modified Glass Surfaces

Glycerol was conjugated to glass test tube surfaces in four configurations by employing two different silane spacers, covalent attachment to glycerol at either the 1- or the 2-position, and with a succinic acid spacer. The resulting surfaces were tested for their ability to inhibit the nucleation of tetrahydrofuran hydrate (THF hydrate) in comparison with polyvinylpyrrolidone (PVP), a known polymeric inhibitor of THF hydrate formation. Contact angle measurements were used as an indication of surface modification throughout the glass derivatization steps. Of the four final surfaces modified with glycerol, only the coating with (3-aminopropyl)triethoxysilane (APTES) and glycerol coupled at the 1-position (leaving a free 1,2-diol) showed significant inhibition of the formation of THF hydrate. The corresponding N-[3-(trimethoxysilyl)propyl]-ethylenediamine (AEAPTMS) coating with glycerol coupled at the 1-position did not show a significant difference over the untreated test tubes. Attachment of glycerol at the 2-position yielded a coating with no benefit over the untreated test tubes regardless of the silane used, and a surface modified with APTES and succinic acid alone enhanced the formation of THF hydrate. The ability to inhibit THF hydrate formation using a polyol-modified surface is a first step in the development of a coating that, alone or in combination with known gas hydrate inhibitors, could be used to prevent gas hydrates from plugging pipelines in field applications.

From ice-binding proteins to bio-inspired antifreeze materials

Ice-binding proteins (IBP) facilitate survival under extreme conditions in diverse life forms. IBPs in polar fishes block further growth of internalized environmental ice and inhibit ice recrystallization of accumulated internal crystals. Algae use IBPs to structure ice, while ice adhesion is critical for the Antarctic bacterium Marinomonas primoryensis. Successful translation of this natural cryoprotective ability into man-made materials holds great promise but is still in its infancy. This review covers recent advances in the field of ice-binding proteins and their synthetic analogues, highlighting fundamental insights into IBP functioning as a foundation for the knowledge-based development of cheap, bio-inspired mimics through scalable production routes. Recent advances in the utilisation of IBPs and their analogues to e.g. improve cryopreservation, ice-templating strategies, gas hydrate inhibition and other technologies are presented.

Effect of antifreeze protein on heterogeneous ice nucleation based on a two-dimensional random-field Ising model

Antifreeze proteins (AFPs) are the key biomolecules that protect many species from suffering the extreme conditions. Their unique properties of antifreezing provide the potential of a wide range of applications. Inspired by the present experimental approaches of creating an antifreeze surface by coating AFPs, here we present a two-dimensional random-field lattice Ising model to study the effect of AFPs on heterogeneous ice nucleation. The model shows that both the size and the free-energy effect of individual AFPs and their surface coverage dominate the antifreeze capacity of an AFP-coated surface. The simulation results are consistent with the recent experiments qualitatively, revealing the origin of the surprisingly low antifreeze capacity of an AFP-coated surface when the coverage is not particularly high as shown in experiment. These results will hopefully deepen our understanding of the antifreeze effects and thus be potentially useful for designing novel antifreeze coating materials based on biomolecules.

Durable Anti-Icing Coatings Based on Self-Sustainable Lubricating Layer

A versatile, convenient, and cost-effective method that can be used for grafting anti-icing materials onto different surfaces is highly desirable. Based on mussel-inspired chemistry, the anti-icing coating with extremely low ice adhesion is enabled by constructing a self-sustainable lubricating layer, achieved via modifying solid substrates with a highly hydrophilic conjugate of poly(acrylic acid)-dopamine. Both unfreezable and freezable water remain liquidlike at subzero conditions and synergistically fulfill the role of lubrication for reducing the ice adhesion. The anti-icing coatings show excellent stability in harsh environments and durability after the cross-linking. More importantly, this coating can be applied to various substrates and is of great promise for practical applications.

Icephobic Surfaces Induced by Interfacial Nonfrozen Water

It is known that smooth, hydrophobic solid surfaces exhibit low ice adhesion values, which have been shown to approach a lower ice adhesion strength limit (∼150 kPa) defined by the water receding contact angle. To overcome this limit, we have designed self-lubricating icephobic coatings by blending polydimethylsiloxane (PDMS)-poly(ethylene glycol) (PEG) amphiphilic copolymers into a polymer matrix. Such coatings provide low ice adhesion strength values (∼50 kPa) that can substantially reduce the lower bound of the ice adhesion strength achieved previously on smooth, hydrophobic solid surfaces. Different molecular mechanisms are responsible for the low ice adhesion strength attained by these two approaches. For the smooth hydrophobic surfaces, an increased water depletion layer thickness at the interface weakens the van der Waals' interactions between the ice and the polymeric substrate. For the self-lubricating icephobic coatings, the PEG component of the amphiphilic copolymer is capable of strongly hydrogen bonding with water molecules. The surface hydrogen-bonded water molecules do not freeze, even at substantial levels of subcooling, and therefore serve as a self-lubricating interfacial liquid-like layer that helps to reduce the adhesion strength of ice to the surface. The existence of nonfrozen water molecules at the ice-solid interface is confirmed by solid-state nuclear magnetic resonance (NMR) spectroscopy.

Janus effect of antifreeze proteins on ice nucleation

The mechanism of ice nucleation at the molecular level remains largely unknown. Nature endows antifreeze proteins (AFPs) with the unique capability of controlling ice formation. However, the effect of AFPs on ice nucleation has been under debate. Here we report the observation of both depression and promotion effects of AFPs on ice nucleation via selectively binding the ice-binding face (IBF) and the non-ice-binding face (NIBF) of AFPs to solid substrates. Freezing temperature and delay time assays show that ice nucleation is depressed with the NIBF exposed to liquid water, whereas ice nucleation is facilitated with the IBF exposed to liquid water. The generality of this Janus effect is verified by investigating three representative AFPs. Molecular dynamics simulation analysis shows that the Janus effect can be established by the distinct structures of the hydration layer around IBF and NIBF. Our work greatly enhances the understanding of the mechanism of AFPs at the molecular level and brings insights to the fundamentals of heterogeneous ice nucleation.

Design and synthesis of fluorescence-labeled nucleotide with a cleavable azo linker for DNA sequencing

A cleavable azo linker was synthesized and reacted with 5-(6)-carboxytetramethyl rhodamine succinimidyl ester, followed by further reactions with di(N-succinimidyl) carbonate and 5-(3-amino-1-propynyl)-2'-deoxyuridine 5'-triphosphate [dUTP(AP3)] to obtain the terminal product dUTP-azo linker-TAMRA as a potential reversible terminator for DNA sequencing by synthesis with no need for 3'-OH blocking.

Influence of Block Copolymerization on the Antifreeze Protein Mimetic Ice Recrystallization Inhibition Activity of Poly(vinyl alcohol)

Antifreeze (glyco) proteins are produced by many cold-acclimatized species to enable them to survive subzero temperatures. These proteins have multiple macroscopic effects on ice crystal growth which makes them appealing for low-temperature applications-from cellular cryopreservation to food storage. Poly(vinyl alcohol) has remarkable ice recrystallization inhibition activity, but its mode of action is uncertain as is the extent at which it can be incorporated into other high-order structures. Here the synthesis and characterization of well-defined block copolymers containing poly(vinyl alcohol) and poly(vinylpyrrolidone) by RAFT/MADIX polymerization is reported, as new antifreeze protein mimetics. The effect of adding a large second hydrophilic block is studied across a range of compositions, and it is found to be a passive component in ice recrystallization inhibition assays, enabling retention of all activity. In the extreme case, a block copolymer with only 10% poly(vinyl alcohol) was found to retain all activity, where statistical copolymers of PVA lose all activity with very minor changes to composition. These findings present a new method to increase the complexity of antifreeze protein mimetic materials, while retaining activity, and also to help understand the underlying mechanisms of action.

Synthesis and evaluations of an acid-cleavable, fluorescently labeled nucleotide as a reversible terminator for DNA sequencing

An acid-cleavable linker based on a dimethylketal moiety was synthesized and used to connect a nucleotide with a fluorophore to produce a 3'-OH unblocked nucleotide analogue as an excellent reversible terminator for DNA sequencing by synthesis.

A superrepellent coating with dynamic fluorine chains for frosting suppression: effects of polarity, coalescence and ice nucleation free energy barrier

We designed 3 types oleophobic smooth surface (DTMS, FAS13, FAS17) with dynamic molecular chains and investigated their anti-frosting property under freezing conditions.

The emergence of oxime click chemistry and its utility in polymer science

The synthesis of new, highly functional and dynamic polymeric materials has risen dramatically since the introduction of click chemistry in 2001.

Doubly-dynamic-covalent polymers composed of oxime and oxanorbornene links

Two sets of reversible covalent linkages distributed in series along a polymer backbone were used to prepare a new class of doubly dynamic-covalent polymers capable of reversibly dissociatingviatwo distinct pathways.

Rational, yet simple, design and synthesis of an antifreeze-protein inspired polymer for cellular cryopreservation

Antifreeze (glyco) proteins AF(G)Ps are potent ice recrystallization inhibitors, which is a desirable property to enhance cryopreservation of donor tissue/cells. Here we present the rational synthesis of a new, biomimetic, ice-recrystallization inhibiting polymer derived from a cheap commodity polymer, based on an ampholyte structure. The polymer is used to enhance the cryopreservation of red blood cells, demonstrating a macromolecular solution to tissue storage.

Self-healing hydrogels containing reversible oxime crosslinks

Self-healing oxime-functional hydrogels have been developed that undergo a reversible gel-to-sol transition via oxime exchange under acidic conditions. Keto-functional copolymers were prepared by conventional radical polymerization of N,N-dimethylacrylamide (DMA) and diacetone acrylamide (DAA). The resulting water soluble copolymers (P(DMA-stat-DAA)) were chemically crosslinked with difunctional alkoxyamines to obtain hydrogels via oxime formation. Gel-to-sol transitions were induced by the addition of excess monofunctional alkoxyamines to promote competitive oxime exchange under acidic conditions at 25 °C. The hydrogel could autonomously heal after it was damaged due to the dynamic nature of the oxime crosslinks. In addition to their chemo-responsive behavior, the P(DMA-stat-DAA) copolymers exhibit cloud points which vary with the DAA content in the copolymers. This thermo-responsive behavior of the P(DMA-stat-DAA) was utilized to form physical hydrogels above their cloud point. Therefore, these materials can either form dynamic-covalent or physically-crosslinked gels, both of which demonstrate reversible gelation behavior.

Creating Anti-icing Surfaces via the Direct Immobilization of Antifreeze Proteins on Aluminum

Cryoprotectants such as antifreeze proteins (AFPs) and sugar molecules may provide a solution for icing problems. These anti-icing substances protect cells and tissues from freezing by inhibiting ice formation. In this study, we developed a method for coating an industrial metal material (aluminum, Al) with AFP from the Antarctic marine diatom, Chaetoceros neogracile (Cn-AFP), to prevent or delay ice formation. To coat Al with Cn-AFP, we used an Al-binding peptide (ABP) as a conjugator and fused it with Cn-AFP. The ABP bound well to the Al and did not considerably change the functional properties of AFP. Cn-AFP-coated Al (Cn-AFP-Al) showed a sufficiently low supercooling point. Additional trehalose coating of Cn-AFP-Al considerably delayed AFP denaturation on the Al without affecting its antifreeze activity. This metal surface–coating method using trehalose-fortified AFP can be applied to other metals important in the aircraft and cold storage fields where anti-icing materials are critical.

Design and synthesis of new acid cleavable linkers for DNA sequencing by synthesis

A new kind of acid sensitive tetrahydrofuranyl (THF) linker was synthesized and then reacted with 5-(6)-carboxytetramethylrhodaminesuccinimidyl ester (5(6)-TAMRA, SE), followed by di(N-succinimidyl) carbonate (DSC) and modified 2'-deoxyuridine triphosphate (dUTP); the final product, as a reversible terminator for DNA sequencing by synthesis (DNA SBS), was given obtained and confirmed by 1H-NMR, 31P-NMR, and HRMS with purity of up to 99%. The synthesized dye-labeled terminator incorporated into DNA strand successfully, and the fluorophore was cleaved completely under acidic conditions. The preliminary results encourage us to explore more acid-sensitive linkers for DNA SBS to increase the cleavage efficiency under weakly acidic conditions.

Tunable Hydrophilic or Amphiphilic Coatings: A "Reactive Layer Stack" Approach

Thin films with tunable properties are very interesting for potential applications as functional coatings with, for example, anti-icing or improved easy-to-clean properties. A novel "reactive layer stack" approach was developed to create covalently grafted mono- and multilayers of poly(glycidyl methacrylate)/poly(tert-butyl acrylate) diblock copolymers. Because these copolymers contain poly(glycidyl methacrylate) blocks they behave as self-cross-linking materials after creation of acrylic acid functionalities by splitting off the tert-butyl units. The ellipsometrically determined coating thickness of the resulting hydrophilic multilayers depended linearly on the number of applied layers. Amphiphilic films with tunable wettability were prepared using triblock terpolymers with an additional poly(methyl methacrylate) block. The mechanism of the formation of the (multi)layers was investigated in detail by studying the acidolysis of the surface-linked tert-butyl acrylate blocks by infrared reflection absorbance spectroscopy, accompanied by surface analysis using atomic force microscopy and contact angle measurements. In the case of the amphiphilic and switchable terpolymer layers this reaction was very sensitive to the used acidic reagent.

Quantitative study on the antifreeze protein mimetic ice growth inhibition properties of poly(ampholytes) derived from vinyl-based polymers

Antifreeze (glyco) proteins (AF(G)Ps) from the blood of polar fish species are extremely potent ice recrystallization inhibitors (IRI), but are difficult to synthesise or extract from natural sources. Despite this challenge, materials which display IRI are appealing due to their ability to enhance cellular cryopreservation, for applications including regenerative and transplantation medicine. Here, poly(ampholytes), which contain a mixture of cationic and anionic side chains are quantitatively evaluated for their IRI activity. Poly(aminoethyl methacrylate), obtained by RAFT polymerization, is functionalised with succinic anhydride to generate the poly(ampholytes). The charge balance of the side chains is shown to be crucial, with only 50 : 50 mixtures having strong IRI activity, which also scales with molecular weight. This is the first example of a non-hydroxylated synthetic polymer with quantifiable IRI activity and raises questions about the mechanism of IRI, as the polymers have no obvious ice-binding motif. The ampholytic structure is shown to be transferable to carbohydrate-centred polymers with activity retained, but poly(betaines) are shown to be inactive.