Photocurrent Enhancement of n-Type Cu2O Electrodes Achieved by Controlling Dendritic Branching Growth

Direct Electrochemical Synthesis of Metal-Organic Frameworks: Cu3 (BTC)2 and Cu(TCPP) on Copper Thin films and Copper-Based Microstructures

Cu thin films and Cu2 O microstructures were partially converted to the Metal-Organic Frameworks (MOFs) Cu3 (BTC)2 or Cu(TCPP) using an electrochemical process with a higher control and at milder conditions compared to the traditional solvothermal MOF synthesis. Initially, either a Cu thin film was sputtered, or different kinds of Cu or Cu2 O microstructures were electrochemically deposited onto a conductive ITO glass substrate. Then, these Cu thin films or Cu-based microstructures were subsequently coated with a thin layer of either Cu3 (BTC)2 or Cu(TCPP) by controlled anodic dissolution of the Cu-based substrate at room temperature and in the presence of the desired organic linker molecules: 1,3,5-benzenetricarboxylic acid (BTC) or photoactive 4,4',4'',4'''-(Porphine-5,10,15,20-tetrayl) tetrakis(benzoic acid) (TCPP) in the electrolyte. An increase in size of the Cu micro cubes with exposed planes [100] of 38,7 % for the Cu2 O@Cu3 (BTC)2 and a 68,9 % increase for the Cu2 O@Cu(TCPP) was roughly estimated. Finally, XRD, Raman spectroscopy and UV-vis absorption spectroscopy were used to characterize the initial Cu films or Cu-based microstructures, and the obtained core-shell Cu2 O@Cu(BTC) and Cu2 O@Cu(TCPP) microstructures.

Spectrally Resolved Single Particle Photoluminescence Microscopy Reveals Heterogeneous Photocorrosion Activity of Cuprous Oxide Microcrystals

Photocorrosion of cuprous oxide (Cu₂O) has notably limited its application as an efficient photocatalyst. We report a facile approach to visualize in situ formation of copper and oxygen vacancies on the Cu₂O surface under ambient condition. By imaging photoexcited single Cu₂O particles, the resultant photoluminescence generated at Cu₂O surface enable effective localization of copper and oxygen vacancies. Single particle photoluminescence imaging showed substantial heterogeneity in the rate of defect formation at different facets with the truncated corners achieving the fastest initial rate of photooxidation before subsequently changing to the face and edge sites as the photocorrosion proceeds. The generation of copper or oxygen vacancy is proportional to the photoexcitation power, while pH-dependent studies rationalized alkaline conditions for the formation of copper vacancy. Reaction in an electron-hole scavenger system showed that photooxidation and photoreduction will simultaneously occur, yet heterogeneously on the surface of Cu₂O, with rate of copper vacancy formation being fastest.

Exploration of Copper Oxide Nanoneedle Electrosynthesis Applied in the Degradation of Methylene Blue

In this study, we report a low cost, fast and unexplored electrochemical synthesis strategy of copper oxide nanoneedles films as well as their morphological and chemical characterization. The nanostructured films were prepared using electrochemical anodization in alkaline electrolyte solutions of ethylene glycol, water and fluoride ions. The film morphology shows nanoneedle-shaped structures, with lengths up to 1–2 μm; meanwhile, high-resolution X-ray photoelectron spectroscopy (HRXPS) and spectroscopy Raman analyses indicate that a mixture of Cu(II) and Cu(I) oxides, or only Cu(I) oxide, is obtained as the percentage of water in the electrolyte solution decreases. A preliminary study was also carried out for the photocatalytic degradation of the methylene blue (MB) dye under irradiation with simulated sunlight in the presence of the nanoneedles obtained, presenting a maximum degradation value of 88% of MB and, thus, demonstrating the potential characteristics of the material investigated in the degradation of organic dyes.

Defective Indium Tin Oxide Forms an Ohmic Back Contact to an n-Type Cu2O Photoanode to Accelerate Charge-Transfer Kinetics for Enhanced Low-Bias Photoelectrochemical Water Splitting

In significant contrast to the tremendous research efforts mostly geared to addressing the severe hole accumulation at the back contact of a p-type Cu₂O photocathode with a fluorine-doped tin oxide (FTO) substrate, sluggish electron transfer from an n-type Cu₂O photoanode to a tin-doped indium oxide (ITO) substrate has been largely overlooked. To tackle this issue that has been reported to largely limit the photoelectrochemical performance of n-type Cu₂O photoanodes at a low bias, the present contribution puts forward a strategy to introduce oxygen vacancies into the ITO substrate via an unprecedented yet facile electrochemical approach. Such defect engineering turns out to decrease the work function of the ITO substrate, which in turn approaches the conduction band extremum of n-Cu₂O to highly efficiently extract the photoexcited electrons therein. Moreover, the dendritic growth of n-Cu₂O is, in the meantime, interfered by the oxygen vacancy manifested as pinholes distributed over the ITO substrate, which is thereby crystallized into several small grains with augmented surface roughness that is in favor of the injection of the photoexcited hole into the electrolyte. Such facile interfacial charge-transfer kinetics leads to a significant cathodic shift amounting to 200 mV of the onset potential to 0 V_Ag/AgCl, whereat the n-Cu₂O photoanode deposited on the defective ITO substrate delivers the maximum photocurrent density reaching 2 mA cm^-2 and, more significantly, its applied bias photon-to-current efficiency (ABPE) reaches 1.1%, which is among the highest performance reported to date for a variety of state-of-the-art metal oxide-based photoanodes in the literature.

TiO2@Cu2O n-n Type Heterostructures for Photochemistry

A TiO2@Cu2O semiconductor heterostructure with better photochemical response compared to TiO2 was obtained using an electrochemical deposition method of Cu2O on the surface of TiO2 nanotubes. The choice of 1D nanotubes was motivated by the possibility of achieving fast charge transfer, which is considered best suited for photochemical applications. The morphology and structural properties of the obtained heterojunction were determined using standard methods -SEM and Raman spectroscopy. Analysis of photoelectrochemical properties showed that TiO2@Cu2O heterostructures exhibit better properties resulting from an interaction with sunlight than TiO2. A close relationship between the morphology of the heterostructures and their photoproperties was also demonstrated. Investigations representing a combination of photoelectrochemical cells for hydrogen production and photocatalysis-photoelectrocatalysis-were also carried out and confirmed the observations on the photoproperties of heterostructures. Analysis of the Mott-Schottky plots as well as photoelectrochemical measurements (Iph-V, Iph-t) showed that TiO2 as well as, unusually, Cu2O exhibit n-type conductivity. On this basis, a new energy diagram of the TiO2@Cu2O system was proposed. It was found that TiO2@Cu2O n-n type heterostructure prevents the processes of photocorrosion of copper(I) oxide contained in a TiO2-based heterostructure.

The effect of redox potential on the removal characteristic of divalent cations during activated carbon-based capacitive deionization

The main objective of the study is to explore the removal characteristics of Cu²⁺ and Zn²⁺ ions in activated carbon-based capacitive deionization (CDI). In this work, CDI experiments were performed to remove divalent ions (e.g., Cu²⁺, Zn²⁺, and Ca²⁺) from single- and multicomponent aqueous solutions. As evidenced, divalent heavy metals could be successfully removed by charging the CDI cell at 1.2 V. Notably, the preferential removal of Cu²⁺ ions over Zn²⁺ and Ca²⁺ ions was observed in the charging step. The removal capacities for Cu²⁺, Zn²⁺, and Ca²⁺ ions in a competitive environment were 29.6, 19.6, and 13.8 μmol/g, respectively. In contrast, the regeneration efficiencies for the removal of Cu²⁺ and Zn²⁺ were much lower than that of Ca²⁺, suggesting the occurrence of irreversible Faradaic reactions on the cathode. X-ray photoelectron spectroscopy analysis demonstrated that Cu²⁺ ions were reduced to Cu(I) and Zn²⁺ ions were transformed to ZnO/Zn(OH)₂ on the cathode. Therefore, there were two major mechanisms for the removal of divalent heavy metal ions: capacitive electrosorption and cathodic electrodeposition. Specifically, the reduction potential played a crucial role in determining the removal characteristics. When regarding divalent cations with similar hydrated sizes, the divalent cation with a higher reduction potential tended to be separated by cathodic electrodeposition rather than double-layer charging, indicating the high removal selectivity of activated carbon-based CDI. This paper constitutes a significant contribution to promoting the application of CDI for contaminant sequestration.

Grey hematite photoanodes decrease the onset potential in photoelectrochemical water oxidation

Photoelectrochemical (PEC) water splitting for solar energy conversion into chemical fuels has attracted intense research attention. The semiconductor hematite (α-Fe₂O₃), with its earth abundance, chemical stability, and efficient light harvesting, stands out as a promising photoanode material. Unfortunately, its electron affinity is too deep for overall water splitting, requiring additional bias. Interface engineering has been used to reduce the onset potential of hematite photoelectrode. Here we focus instead on energy band engineering hematite by shrinking the crystal lattice, and the water-splitting onset potential can be decreased from 1.14 to 0.61 V vs. the reversible hydrogen electrode. It is the lowest record reported for a pristine hematite photoanode without surface modification. X-ray absorption spectroscopy and magnetic properties suggest the redistribution of 3d electrons in the as-synthesized grey hematite electrode. Density function theory studies herein show that the smaller-lattice-constant hematite benefits from raised energy bands, which accounts for the reduced onset potential.

Morphology control of Cu and Cu2O through electrodeposition on conducting polymer electrodes

Here we demonstrate the morphology control of Cu and Cu₂O through electrodeposition on conducting polymer surface.

3D-printed Cu2O photoelectrodes for photoelectrochemical water splitting

Photoelectrochemical (PEC) water splitting is an alternative to fossil fuel combustion involving the generation of renewable hydrogen without environmental pollution or greenhouse gas emissions. Cuprous oxide (Cu₂O) is a promising semiconducting material for the simple reduction of hydrogen from water, in which the conduction band edge is slightly negative compared to the water reduction potential. However, the solar-to-hydrogen conversion efficiency of Cu₂O is lower than the theoretical value due to a short carrier-diffusion length under the effective light absorption depth. Thus, increasing light absorption in the electrode-electrolyte interfacial layer of a Cu₂O photoelectrode can enhance PEC performance. In this study, a Cu₂O 3D photoelectrode comprised of pyramid arrays was fabricated using a two-step method involving direct-ink-writing of graphene structures. This was followed by the electrodeposition of a Cu current-collecting layer and a p-n homojunction Cu₂O photocatalyst layer onto the printed structures. The performance for PEC water splitting was enhanced by increasing the total light absorption area (A _a) of the photoelectrode via controlling the electrode topography. The 3D photoelectrode (A _a = 3.2 cm²) printed on the substrate area of 1.0 cm² exhibited a photocurrent (I _ph) of -3.01 mA at 0.02 V (vs. RHE), which is approximately three times higher than that of a planar photoelectrode with an A _a = 1.0 cm² (I _ph = -0.91 mA). Our 3D printing strategy provides a flexible approach for the design and the fabrication of highly efficient PEC photoelectrodes.

Recent Advances in the Design and Photocatalytic Enhanced Performance of Gold Plasmonic Nanostructures Decorated with Non-Titania Based Semiconductor Hetero-Nanoarchitectures

Plasmonic photocatalysts combining metallic nanoparticles and semiconductors have been aimed as versatile alternatives to drive light-assisted catalytic chemical reactions beyond the ultraviolet (UV) regions, and overcome one of the major drawbacks of the most exploited photocatalysts (TiO2 or ZnO). The strong size and morphology dependence of metallic nanostructures to tune their visible to near-infrared (vis-NIR) light harvesting capabilities has been combined with the design of a wide variety of architectures for the semiconductor supports to promote the selective activity of specific crystallographic facets. The search for efficient heterojunctions has been subjected to numerous studies, especially those involving gold nanostructures and titania semiconductors. In the present review, we paid special attention to the most recent advances in the design of gold-semiconductor hetero-nanostructures including emerging metal oxides such as cerium oxide or copper oxide (CeO2 or Cu2O) or metal chalcogenides such as copper sulfide or cadmium sulfides (CuS or CdS). These alternative hybrid materials were thoroughly built in past years to target research fields of strong impact, such as solar energy conversion, water splitting, environmental chemistry, or nanomedicine. Herein, we evaluate the influence of tuning the morphologies of the plasmonic gold nanostructures or the semiconductor interacting structures, and how these variations in geometry, either individual or combined, have a significant influence on the final photocatalytic performance.

Solution-Processed Synthesis of Copper Oxide (Cu x O) Thin Films for Efficient Photocatalytic Solar Water Splitting

This article reports a solution-processed synthesis of copper oxide (Cu x O) to be used as a potential photocathode for solar hydrogen production in the solar water-splitting system. Cu x O thin films were synthesized through the reduction of copper iodide (CuI) thin films by sodium hydroxide (NaOH), which were deposited by the spin coating method from CuI solution in a polar aprotic solvent (acetonitrile). The phase and crystalline quality of the synthesized Cu x O thin films prepared at various annealing temperatures were investigated using various techniques. The X-ray diffraction and energy dispersive X-ray spectroscopy studies confirm the presence of Cu2O, CuO/Cu2O mixed phase, and pure CuO phase at annealing temperatures of 250, 300, and 350 °C, respectively. It is revealed from the experimental findings that the synthesized Cu x O thin films with an annealing temperature of 350 °C possess the highest crystallinity, smooth surface morphology, and higher carrier density. The highest photocurrent density of -19.12 mA/cm2 at -1 V versus RHE was achieved in the photoelectrochemical solar hydrogen production system with the use of the Cu x O photocathode annealed at a temperature of 350 °C. Therefore, it can be concluded that Cu x O synthesized by the spin coating method through the acetonitrile solvent route can be used as an efficient photocathode in the solar water-splitting system.

Effect of bandgap alignment on the photoreduction of CO2 into methane based on Cu2O-decorated CuO microspheres

Semiconductors' band gap alignment is important for the photoreduction of CO2 to methane. In the paper, two kinds of Cu2O-decorated CuO microspheres composed with nanoflakes were prepared by using two different methods. Their electron behaviors were studied from the XPS spectra and photoelectrochemical measurements. Both samples are p-type CuO covered with an amount of Cu2O nanoparticles on their surface. Combined with their bandgaps and flat band potentials, CuO-Mic has a well-matched bandgap alignment between Cu2O and CuO, which is favorable for the separation of photogenerated electron-hole pairs. Those photogenerated carriers are beneficial for the conversion of CO2 to CH4, as an 8-electron process for the conversion of CO2 to CH4 will consume more photogenerated electrons for the chemical reactions than that of the 2-electron process for CO2 reduction to CO. Therefore, CuO-Mic has much better photocatalytic activity for CO2 reduction to CH4 with a CH4 yield ten times higher than that of CuO-Hyd under a visible light irradiation, the CO yields of the CO2 reduction are identical.

Surfactant-assisted synthesis of copper oxide nanorods for the enhanced photocatalytic degradation of Reactive Black 5 dye in wastewater

In this study, copper oxide nanorods were synthesized via surfactant-assisted chemical precipitation method and characterized by using X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and UV-Visible spectrometer. XRD result reveals that CuO nanorods were structured in the monoclinic phase. SEM image suggested that synthesized CuO were shaped like nanorod with approximately 20-40 nm width and 500-800 nm length. The observed band gap calculated from UV-Visible absorption studies is 1.45 eV. As-prepared CuO nanorods were applied as a photocatalyst for the degradation of textile dye Reactive Black 5 (RB-5) in aqueous solution under the presence of visible light. The result exhibited that an enhanced degradation of RB-5 was achieved around 98% within 300 min and the experimental values were well matched with the linear fit model (R² = 0.97) and the observed rate constant found to be 5 × 10^-3 min^-1. Therefore, as-synthesized CuO nanorods can be applied as a potential photocatalyst material for the degradation of organic pollutants in the wastewater.

Defect-Cluster-Boosted Solar Photoelectrochemical Water Splitting by n-Cu2 O Thin Films Prepared Through Anisotropic Crystal Growth

Anisotropic growth of Cu₂ O crystals deposited on an indium-doped tin oxide-coated glass substrate through facile electrodeposition and low-temperature calcination results in favorable solar photoelectrochemical water splitting. XRD, TEM, and SEM reveal that appreciable oxygen vacancies are populated in the Cu₂ O crystals with a highly branched dendritic thin film morphology, which are further substituted by Cu atoms to form Cu antisite defects exclusively along the [111] direction. The post-thermal treatment presumably accelerates such migration of the lattice imperfections, favoring the exposure of the catalytically active (111) facets. The Cu₂ O thin film derived in this way shows n-type conduction with a donor concentration in the order of 10¹⁷  cm^-3 and a flat-band potential of -1.19 V vs. Ag/AgCl, which is also confirmed by Mott-Schottky analysis. The material is employed as a photoanode and delivers a photocurrent density of 2.2 mA cm^-2 at a potential of 0.3 V vs. Ag/AgCl, surpassing reported values more than twofold. Such superiority mostly originates from the synergism of the selective facet exposure within the Cu₂ O crystals, which have decent crystallinity, as shown by Raman and photoluminescence spectroscopy, and a favorable bandgap of 2.1 eV, as confirmed by UV/Vis spectroscopy. The n-type Cu₂ O thin film reported herein holds excellent promise for solar-related applications.

Sandwich-Nanostructured n-Cu2O/AuAg/p-Cu2O Photocathode with Highly Positive Onset Potential for Improved Water Reduction

An n-Cu₂O layer formed a high-quality buried junction with p-Cu₂O to increase the photovoltage and thus to shift the turn-on voltage positively. Mott-Schottky measurements confirmed that the improvement benefited from a positive shift in flat-band potential. The obtained extremely positive onset potential, 0.8 V_RHE in n-Cu₂O/AuAg/p-Cu₂O, is comparable with measurements from water reduction catalysts. The AuAg alloy sandwiched between the homojunction of n-Cu₂O and p-Cu₂O improved the photocatalytic performance. This alloy both served as an electron relay and promoted electron-hole pair generation in nearby semiconductors; the charge transfer between n-Cu₂O and p-Cu₂O in the sandwich structure was measured with X-ray absorption spectra. The proposed sandwich structure can be considered as a new direction for the design of efficient solar-related devices.

Giant Defect-Induced Effects on Nanoscale Charge Separation in Semiconductor Photocatalysts

Defects can markedly impact the performance of semiconductor-based photocatalysts, where the spatial separation of photogenerated charges is required for converting solar energy into fuels. However, understanding exactly how defects affect photogenerated charge separation at nanometer scale remains quite challenging. Here, using time- and space-resolved surface photovoltage approaches, we demonstrate that the distribution of surface photogenerated charges and the direction of photogenerated charge separation are determined by the defects distributed within a 100 nm surface region of a photocatalytic Cu₂O particle. This is enabled by the defect-induced charge separation process, arising from the trapping of electrons at the near-surface defect states and the accumulation of holes at the surface states. More importantly, the driving force for defect-induced charge separation is greater than 4.2 kV/cm and can be used to drive photocatalytic reactions. These findings highlight the importance of near-surface defect engineering in promoting photogenerated charge separation and manipulating surface photogenerated charges; further, they open up a powerful avenue for improving photocatalytic charge separation and solar energy conversion efficiency.

Facet- and structure-dependent catalytic activity of cuprous oxide/polypyrrole particles towards the efficient reduction of carbon dioxide to methanol

The preparation of cost-effective, stable catalysts for the selective reduction of carbon dioxide (CO2) to C1 products such as methanol is extremely important because methanol can be used directly as a fuel or it can be converted into other value-added products. However, the catalysts currently used for the reduction of CO2 to methanol exhibit poor selectivity, poor stability and very low faradaic efficiency. Herein, we used low-cost, stable cuprous oxide/polypyrrole (Cu2O/Ppy) particles having structures of octahedra and icosahedra (microflowers) that were prepared on linen texture (LT) papers for the selective reduction of CO2 to form a value-added single C1 product, methanol. The Cu2O/Ppy particles possessing both octahedral and microflower shapes with exposed low-index (111) facets and high-index (311) and (211) facets are denoted as Cu2O(OL-MH)/Ppy particles. The as-prepared Cu2O(OL-MH)/Ppy particles exhibited high catalytic activity and selectivity towards the electrochemical reduction of CO2 at -0.85 V vs. RHE to form methanol, with a faradaic efficiency of 93 ± 1.2% and an average methanol formation rate of 1.61 ± 0.02 μmol m-2 s-1. The X-ray photoelectron spectroscopy (XPS) analysis revealed that the pyrrolic nitrogen atoms present in the Ppy shell played a dominant role as active sites for CO2 molecules. The Raman bands of Ppy and Cu2O did not shift even after being subjected to electrolysis for several hours, suggesting superior stability of the Cu2O(OL-MH)/Ppy particles. The high resolution microscopic, spectroscopic, diffraction and electrochemical analysis results clearly revealed that the Ppy shell protected the Cu2O particles and avoided corrosion, dissolution, and structural and crystal facet changes, leading to greater stability. The low-cost, durable, flexible, and catalytically active Cu2O(OL-MH)/Ppy LT paper holds great potential for catalytic, photocatalytic and energy storage applications.

Tremella-like ZnIn2S4/graphene composite based photoelectrochemical sensor for sensitive detection of dopamine

Tremella-like ZnIn₂S₄ (ZISt) and flower-like microsphere ZnIn₂S₄ (ZISm) were synthesized via a straightforward hydrothermal method. It was found that the ZISt was superior to ZISm for photoelectrochemical (PEC) sensing because of its large surface area and high photocatalytic activity. A composite of ZISt and graphene (GR) was prepared and used for the PEC sensing of dopamine (DA). Here DA acted as an electron donor to scavenge the hole and inhibit the charge recombination. The GR enhanced visible light absorption and accelerated electron transfer, amplifying the photocurrent signal. The strong chelating coordination interaction between DA and Zn(II) in ZISt guaranteed the selective adsorption of target analyte. Thus the resulting ZISt/GR photoelectrode showed sensitive and selective PEC response to DA. Under the optimized conditions, the linear response range was from 0.01 to 20 μM, and the detection limit was down to 0.001 μM. Additionally, the sensor had good stability and reproducibility, and it could be used for the detection of DA in real samples.

Optimization of photoelectrochemical performance in Pt-modified p-Cu2O/n-Cu2O nanocomposite

As it is expected to be one of the most promising materials for utilizing solar energy, Cu2O has attracted considerable attention with respect to the achievement of solar energy conversion. Until now, the photocurrent densities of all planar structure of the Cu2O photocathode have not even come close to the theoretical value of -14.7 mA cm-2 due to the incompatible light absorption and charge carrier diffusion lengths. Here, we have fabricated p-n Cu2O homojunction nanocomposite by multiple steps of electrochemical deposition processing with the optimization of deposition periods. The p-Cu2O/n-Cu2O nanocomposite fabricated by optimized pH (4.9) and deposition time (4 min) exhibited double the photocurrent density of that of the bare p-Cu2O photocathode. And the highest photocurrent density of nanostructured p-n Cu2O nanorod homojunction photocathode with a p-Cu2O blocking layer reached -10.0 mA cm-2 at 0 V versus the reversible hydrogen electrode under simulated AM 1.5G illumination (100 mW cm-2).

Controllable synthesis, formation mechanism, and enhanced microwave absorption of dendritic AgFe alloy/Fe3O4 nanocomposites

Dendritic AgFe alloy/Fe₃O₄ nanocomposites with tunable composition and size synthesized via a selective attachment and anisotropic growth exhibit enhanced microwave absorption.

Electrochemical fabrication of shape-controlled Cu2O with spheres, octahedrons and truncated octahedrons and their electrocatalysis for ORR

Morphology-controlled synthesis of Cu₂O is achieved by potentiostatic electrodeposition and it is used as an electrocatalyst for the oxygen reduction reaction.

Effect of cuprous oxide with different sizes on thermal and combustion behaviors of unsaturated polyester resin

Cuprous oxide (Cu₂O) as an effective catalyst has been applied to enhance the fire safety of unsaturated polyester resin (UPR), but the particle size influence on combustion behaviors has not been previously reported. Herein, the UPR/Cu₂O composites (metal oxide particles with average particle-size of 10, 100, and 200nm) were successfully synthesized by thermosetting process. The effects of Cu₂O with different sizes on thermostability and combustion behaviors of UPR were characterized by TGA, MCC, TG-IR, FTIR, and SSTF. The results revel that the addition of Cu₂O contributes to sufficient decomposition of oxygen-containing compounds, which is beneficial to the release of nontoxic compounds. The smallest-sized Cu₂O performs the excellent catalytic decomposition effect and promotes the complete combustion of UPR, which benefits the enhancement of fire safety. While the other additives retard pyrolysis process and yield more char residue, and thus the flame retardancy of UPR composites was improved. Therefore, catalysis plays a major role for smaller-sized particles during thermal decomposition of matrix, while flame retarded effect became gradual distinctly for the larger-sized additives.

Stoichiometry, Morphology, and Size-Controlled Electrochemical Fabrication of CuxO (x = 1, 2) at Underpotential

A new one-step electrochemical approach has been developed for the morphology, size, and stoichiometry-controlled synthesis of Cu₂O, CuO, and Cu₂O/CuO composite structures at room temperature without using surfactants, capping agents, or any other additives. The electrochemical deposition of a Cu monolayer using underpotential deposition (UPD) and the flow rate of oxygen gas bubbled through the deposition solution used for oxidation of the Cu layer are the key parameters for controlling the stoichiometry of the Cu_xO (x = 1, 2) structures. The morphologies, crystallinity, stoichiometries, optical properties, and photoelectrochemical properties of the as-electrodeposited Cu₂O and CuO materials were analyzed using scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), energy dispersive spectroscopy (EDS), UV-vis absorption, and photoelectrochemical (PEC) techniques. The results indicated that the Cu₂O and CuO materials electrodeposited on both indium tin oxide coated (ITO) quartz and gold electrodes using this new electrochemical technique exhibit high-quality single crystalline structures and high photoactivity with rapid photoelectrical response to light irradiation.

Morphology and phase tuning of α- and β-MnO2 nanocacti evolved at varying modes of acid count for their well-coordinated energy storage and visible-light-driven photocatalytic behaviour

α and β of MnO₂ nanocacti (comprising nanowires with 1–10 nm diameter self assembled by ultrathin sheets) as well as MnO₂ nanorods (10–40 nm diameter) are synthesized without any seed or template.

The exceptional adsorption ability and gas-detection sensitivity of Cu2O with tunable morphologies

The systematic and delicate geometry control of Cu₂O nanostructures with different size can be achieved by simply tuning the dropping speed of NH₂OH HCl, the volume of solvent and the concentration of NaOH.

One-pot synthesis and first-principles elasticity analysis of polymorphic MnO2 nanorods for tribological assessment as friction modifiers

XRD analysis of hydrothermally synthesized polymorphic MnO₂ nanorods and their frictional torque when added with palm oil as against pure palm oil.

Hollow CuxO (x = 2, 1) micro/nanostructures: synthesis, fundamental properties and applications

In this review, we comprehensively summarize the important advances in hollow Cu_xO micro/nanostructures, including the universal synthesis strategies, the interfacial Cu–O atomic structures as well as the intrinsic properties, and potential applications. Remarks on emerging issues and promising research directions are also discussed.

P–N depleted bulk BiOBr/α-Fe2O3 heterojunctions applied for unbiased solar water splitting

P–N depleted bulk BiOBr/α-Fe₂O₃ heterojunction (DBH) nanostructures with the growth of (001) BiOBr facets were prepared via a simple hydrothermal method. Such DBH nanostructures show superior hydrogen evolution efficiency.

A one-pot hydrothermal synthesis of graphene/CdS:Mn photocatalyst for photoelectrochemical sensing of glutathione

The GR/CdS:Mn composite was fabricated by a simple hydrothermal synthesis which illustrates excellent performance for the photoelectrochemical detection of glutathione.

High spatial dynamics-photoluminescence imaging reveals the metallurgy of the earliest lost-wax cast object

Photoluminescence spectroscopy is a key method to monitor defects in semiconductors from nanophotonics to solar cell systems. Paradoxically, its great sensitivity to small variations of local environment becomes a handicap for heterogeneous systems, such as are encountered in environmental, medical, ancient materials sciences and engineering. Here we demonstrate that a novel full-field photoluminescence imaging approach allows accessing the spatial distribution of crystal defect fluctuations at the crystallite level across centimetre-wide fields of view. This capacity is illustrated in archaeology and material sciences. The coexistence of two hitherto indistinguishable non-stoichiometric cuprous oxide phases is revealed in a 6,000-year-old amulet from Mehrgarh (Baluchistan, Pakistan), identified as the oldest known artefact made by lost-wax casting and providing a better understanding of this fundamental invention. Low-concentration crystal defect fluctuations are readily mapped within ZnO nanowires. High spatial dynamics-photoluminescence imaging holds great promise for the characterization of bulk heterogeneous systems across multiple disciplines.

Photoluminescence is a powerful probe of chemical composition and structure, but it is challenging to image heterogeneous materials over large scale. Thoury et al. develop a full-field imaging approach to map two cuprous oxide phases in the earliest known lost-wax cast artefact manufactured 6,000 years ago.

Profiling Photoinduced Carrier Generation in Semiconductor Microwire Arrays via Photoelectrochemical Metal Deposition

Au was photoelectrochemically deposited onto cylindrical or tapered p-Si microwires on Si substrates to profile the photoinduced charge-carrier generation in individual wires in a photoactive semiconductor wire array. Similar experiments were repeated for otherwise identical Si microwires doped to be n-type. The metal plating profile was conformal for n-type wires, but for p-type wires was a function of distance from the substrate and was dependent on the illumination wavelength. Spatially resolved charge-carrier generation profiles were computed using full-wave electromagnetic simulations, and the localization of the deposition at the p-type wire surfaces observed experimentally correlated well with the regions of enhanced calculated carrier generation in the volumes of the microwires. This technique could potentially be extended to determine the spatially resolved carrier generation profiles in a variety of mesostructured, photoactive semiconductors.

Cu2O Photocathode for Low Bias Photoelectrochemical Water Splitting Enabled by NiFe-Layered Double Hydroxide Co-Catalyst

Layered double hydroxides (LDHs) are bimetallic hydroxides that currently attract considerable attention as co-catalysts in photoelectrochemical (PEC) systems in view of water splitting under solar light. A wide spectrum of LDHs can be easily prepared on demand by tuning their chemical composition and structural morphology. We describe here the electrochemical growth of NiFe-LDH overlayers on Cu₂O electrodes and study their PEC behavior. By using the modified Cu₂O/NiFe-LDH electrodes we observe a remarkable seven-fold increase of the photocurrent intensity under an applied voltage as low as −0.2 V vs Ag/AgCl. The origin of such a pronounced effect is the improved electron transfer towards the electrolyte brought by the NiFe-LDH overlayer due to an appropriate energy level alignment. Long-term photostability tests reveal that Cu₂O/NiFe-LDH photocathodes show no photocurrent loss after 40 hours of operation under light at −0.2 V vs Ag/AgCl low bias condition. These improved performances make Cu₂O/NiFe-LDH a suitable photocathode material for low voltage H₂ production. Indeed, after 8 hours of H₂ production under −0.2 V vs Ag/AgCl the PEC cell delivers a 78% faradaic efficiency. This unprecedented use of Cu₂O/NiFe-LDH as an efficient photocathode opens new perspectives in view of low biasd or self-biased PEC water splitting under sunlight illumination.