Photocurrent generation from surface assembled photosystem I on alkanethiol modified electrodes

Molecular interactions of photosystem I and ZIF-8 in bio-nanohybrid materials

Bio-nanohybrid devices featuring natural photocatalysts bound to a nanostructure hold great promise in the search for sustainable energy conversion. One of the major challenges of integrating biological systems is protecting them against harsh environmental conditions while retaining, or ideally enhancing their photophysical properties. In this mainly computational work we investigate an assembly of cyanobacterial photosystem I (PS I) embedded in a metal-organic framework (MOF), namely the zeolitic imidazolate framework ZIF-8. This complex has been reported experimentally [Bennett et al., Nanoscale Adv., 2019, 1, 94] but so far the molecular interactions between PS I and the MOF remained elusive. We show via absorption spectroscopy that PS I remains intact throughout the encapsulation-release cycle. Molecular dynamics (MD) simulations further confirm that the encapsulation has no noticeable structural impact on the photosystem. However, the MOF building blocks frequently coordinate to the Mg2+ ions of chlorophylls in the periphery of the antenna complex. High-level quantum mechanical calculations reveal charge-transfer interactions, which affect the excitonic network and thereby may reversibly change the fluorescence properties of PS I. Nevertheless, our results highlight the stability of PS I in the MOF, as the reaction center remains unimpeded by the heterogeneous environment, paving the way for applications in the foreseeable future.

Dependence of Protein Immobilization and Photocurrent Generation in PSI-FTO Electrodes on the Electrodeposition Parameters

This study investigates the immobilization of cyanobacterial photosystem I (PSI) from Synechocystis sp. PCC 6803 onto fluorine-doped tin oxide (FTO) conducting glass plates to create photoelectrodes for biohybrid solar cells. The fabrication of these PSI-FTO photoelectrodes is based on two immobilization processes: rapid electrodeposition driven by an external electric field and slower adsorption during solvent evaporation, both influenced by gravitational sedimentation. Deposition and performance of photoelectrodes was investigated by UV-Vis absorption spectroscopy and photocurrent measurements. We investigated the efficiency of PSI immobilization under varying conditions, including solution pH, applied electric field intensity and duration, and electrode polarization, with the goals to control (1) the direction of migration and (2) the orientation of the PSI particles on the substrate surface. Variation in the pH value of the PSI solution alters the surface charge distribution, affecting the net charge and the electric dipole moment of these proteins. Results showed PSI migration to the positively charged electrode at pH 6, 7, and 8, and to the negatively charged electrode at pH 4.4 and 5, suggesting an isoelectric point of PSI between 5 and 6. At acidic pH, the electrophoretic migration was largely hindered by protein aggregation. Notably, photocurrent generation was consistently cathodic and correlated with PSI layer thickness, and no conclusions can be drawn on the orientation of the immobilized proteins. Overall, these findings suggest mediated electron transfer from FTO to PSI by the used electrolyte containing 10 mM sodium ascorbate and 200 μM dichlorophenolindophenol.

Photoelectrochemical Two-Dimensional Electronic Spectroscopy (PEC2DES) of Photosystem I: Charge Separation Dynamics Hidden in a Multichromophoric Landscape

We present a nonlinear spectroelectrochemical technique to investigate photosynthetic protein complexes. The PEC2DES setup combines photoelectrochemical detection (PEC) that selectively probes the protein photogenerated charges output with two-dimensional electronic spectroscopy (2DES) excitation that spreads the nonlinear optical response of the system in an excitation-detection map. PEC allows us to distinguish the contribution of charge separation (CS) from other de-excitation pathways, whereas 2DES allows us to disentangle congested spectral bands and evaluate the exciton dynamics (decays and coherences) of the photosystem complex. We have developed in operando phase-modulated 2DES by measuring the photoelectrochemical reaction rate in a biohybrid electrode functionalized with a plant photosystem complex I-light harvesting complex I (PSI-LHCI) layer. Optimizing the photoelectrochemical current signal yields reliable linear spectra unequivocally associated with PSI-LHCI. The 2DES signal is validated by nonlinear features like the characteristic vibrational coherence at 750 cm-1. However, no energy transfer dynamics is observed within the 450 fs experimental window. These intriguing results are discussed in the context of incoherent mixing resulting in reduced nonlinear contrast for multichromophoric complexes, such as the 160 chlorophyll PSI. The presented PEC2DES method identifies generated charges unlike purely optical 2DES and opens the way to probe the CS channel in multichromophoric complexes.

Controlled electron transfer by molecular wires embedded in ultrathin insulating membranes for driving redox catalysis

Organic bilayers or amorphous silica films of a few nanometer thickness featuring embedded molecular wires offer opportunities for chemically separating while at the same time electronically connecting photo- or electrocatalytic components. Such ultrathin membranes enable the integration of components for which direct coupling is not sufficiently efficient or stable. Photoelectrocatalytic systems for the generation or utilization of renewable energy are among the most prominent ones for which ultrathin separation layers open up new approaches for component integration for improving efficiency. Recent advances in the assembly and spectroscopic, microscopic, and photoelectrochemical characterization have enabled the systematic optimization of the structure, energetics, and density of embedded molecular wires for maximum charge transfer efficiency. The progress enables interfacial designs for the nanoscale integration of the incompatible oxidation and reduction catalysis environments of artificial photosystems and of microbial (or biomolecular)-abiotic systems for renewable energy.

Protein Orientation Defines Rectification of Electronic Current via Solid-State Junction of Entire Photosystem-1 Complex

We demonstrate that the direction of current rectification via one of nature's most efficient light-harvesting systems, the photosystem 1 complex (PS1), can be controlled by its orientation on Au substrates. Molecular self-assembly of the PS1 complex using four different linkers with distinct functional head groups that interact by electrostatic and hydrogen bonds with different surface parts of the entire protein PS1 complex was used to tailor the PS1 orientation. We observe an orientation-dependent rectification in the current-voltage characteristics for linker/PS1 molecule junctions. Results of an earlier study using a surface two-site PS1 mutant complex having its orientation set by covalent binding to the Au substrate supports our conclusion. Current-voltage-temperature measurements on the linker/PS1 complex indicate off-resonant tunneling as the main electron transport mechanism. Our ultraviolet photoemission spectroscopy results highlight the importance of the protein orientation for the energy level alignment and provide insight into the charge transport mechanism via the PS1 transport chain.

Observation of anomalous carotenoid and blind chlorophyll activations in photosystem I under synthetic membrane confinements

The role of natural thylakoid membrane confinements in architecting the robust structural and electrochemical properties of PSI is not fully understood. Most PSI studies till date extract the proteins from their natural confinements that can lead to non-native conformations. Recently our group had successfully reconstituted PSI in synthetic lipid membranes using detergent-mediated liposome solubilizations. In this study, we investigate the alterations in chlorophylls and carotenoids interactions and reorganization in PSI based on spectral property changes induced by its confinement in anionic DPhPG and zwitterionic DPhPC phospholipid membranes. To this end, we employ a combination of absorption, fluorescence, and circular dichroism (CD) spectroscopic measurements. Our results indicate unique activation and alteration of photoresponses from the PSI carotenoid (Car) bands in PSI-DPhPG proteoliposomes that can tune the Excitation Energy Transfer (EET), otherwise absent in PSI at non-native environments. Specifically, we observe broadband light harvesting via enhanced absorption in the otherwise non-absorptive green region (500-580 nm) of the Chlorophylls (Chl) along with ~64% increase in the full-width half maximum of the Qy band (650-720 nm). The CD results indicate enhanced Chl-Chl and Chl-Car interactions along with conformational changes in protein secondary structures. Such distinct changes in the Car and Chl bands are not observed in PSI confined in DPhPC. The fundamental insights into membrane microenvironments tailoring PSI subunits reorganization and interactions provide novel strategies for tuning photoexcitation processes and rational designing of biotic-abiotic interfaces in PSI-based photoelectrochemical energy conversion systems.

Printable logic circuits comprising self-assembled protein complexes

This paper describes the fabrication of digital logic circuits comprising resistors and diodes made from protein complexes and wired together using printed liquid metal electrodes. These resistors and diodes exhibit temperature-independent charge-transport over a distance of approximately 10 nm and require no encapsulation or special handling. The function of the protein complexes is determined entirely by self-assembly. When induced to self-assembly into anisotropic monolayers, the collective action of the aligned dipole moments increases the electrical conductivity of the ensemble in one direction and decreases it in the other. When induced to self-assemble into isotropic monolayers, the dipole moments are randomized and the electrical conductivity is approximately equal in both directions. We demonstrate the robustness and utility of these all-protein logic circuits by constructing pulse modulators based on AND and OR logic gates that function nearly identically to simulated circuits. These results show that digital circuits with useful functionality can be derived from readily obtainable biomolecules using simple, straightforward fabrication techniques that exploit molecular self-assembly, realizing one of the primary goals of molecular electronics.

Proteins are promising molecular materials for next-generation electronic devices. Here, the authors fabricated printable digital logic circuits comprising resistors and diodes from self-assembled photosystem I complexes that enable pulse modulation.

Graphene oxide decorated with gold enables efficient biophotovolatic cells incorporating photosystem I

This paper describes the use of reduced graphene oxide decorated with gold nanoparticles as an efficient electron transfer layer for solid-state biophotovoltic cells containing photosystem I as the sole photo-active component. Together with polytyrosine–polyaniline as a hole transfer layer, this device architecture results in an open-circuit voltage of 0.3 V, a fill factor of 38% and a short-circuit current density of 5.6 mA cm⁻² demonstrating good coupling between photosystem I and the electrodes. The best-performing device reached an external power conversion efficiency of 0.64%, the highest for any solid-state photosystem I-based photovoltaic device that has been reported to date. Our results demonstrate that the functionality of photosystem I in the non-natural environment of solid-state biophotovoltaic cells can be improved through the modification of electrodes with efficient charge-transfer layers. The combination of reduced graphene oxide with gold nanoparticles caused tailoring of the electronic structure and alignment of the energy levels while also increasing electrical conductivity. The decoration of graphene electrodes with gold nanoparticles is a generalizable approach for enhancing charge-transfer across interfaces, particularly when adjusting the levels of the active layer is not feasible, as is the case for photosystem I and other biological molecules.

This paper describes the use of reduced graphene oxide decorated with gold nanoparticles as an efficient electron transport layer for solid-state biophotovoltic cells containing photosystem I as the sole photo-active component.

Distance and Potential Dependence of Charge Transport Through the Reaction Center of Individual Photosynthetic Complexes

Charge separation and transport through the reaction center of photosystem I (PSI) is an essential part of the photosynthetic electron transport chain. A strategy is developed to immobilize and orient PSI complexes on gold electrodes allowing to probe the complex's electron acceptor side, the chlorophyll special pair P700. Electrochemical scanning tunneling microscopy (ECSTM) imaging and current-distance spectroscopy of single protein complex shows lateral size in agreement with its known dimensions, and a PSI apparent height that depends on the probe potential revealing a gating effect in protein conductance. In current-distance spectroscopy, it is observed that the distance-decay constant of the current between PSI and the ECSTM probe depends on the sample and probe electrode potentials. The longest charge exchange distance (lowest distance-decay constant β) is observed at sample potential 0 mV/SSC (SSC: reference electrode silver/silver chloride) and probe potential 400 mV/SSC. These potentials correspond to hole injection into an electronic state that is available in the absence of illumination. It is proposed that a pair of tryptophan residues located at the interface between P700 and the solution and known to support the hydrophobic recognition of the PSI redox partner plastocyanin, may have an additional role as hole exchange mediator in charge transport through PSI.

Fullerenes Enhance Self-Assembly and Electron Injection of Photosystem I in Biophotovoltaic Devices

This paper describes the fabrication of microfluidic devices with a focus on controlling the orientation of photosystem I (PSI) complexes, which directly affects the performance of biophotovoltaic devices by maximizing the efficiency of the extraction of electron/hole pairs from the complexes. The surface chemistry of the electrode on which the complexes assemble plays a critical role in their orientation. We compared the degree of orientation on self-assembled monolayers of phenyl-C61-butyric acid and a custom peptide on nanostructured gold electrodes. Biophotovoltaic devices fabricated with the C61 fulleroid exhibit significantly improved performance and reproducibility compared to those utilizing the peptide, yielding a 1.6-fold increase in efficiency. In addition, the C61-based devices were more stable under continuous illumination. Our findings show that fulleroids, which are well-known acceptor materials in organic photovoltaic devices, facilitate the extraction of electrons from PSI complexes without sacrificing control over the orientation of the complexes, highlighting this combination of traditional organic semiconductors with biomolecules as a viable approach to coopting natural photosynthetic systems for use in solar cells.

Rational design of artificial redox-mediating systems toward upgrading photobioelectrocatalysis

Photobioelectrocatalysis has recently attracted particular research interest owing to the possibility to achieve sunlight-driven biosynthesis, biosensing, power generation, and other niche applications. However, physiological incompatibilities between biohybrid components lead to poor electrical contact at the biotic-biotic and biotic-abiotic interfaces. Establishing an electrochemical communication between these different interfaces, particularly the biocatalyst-electrode interface, is critical for the performance of the photobioelectrocatalytic system. While different artificial redox mediating approaches spanning across interdisciplinary research fields have been developed in order to electrically wire biohybrid components during bioelectrocatalysis, a systematic understanding on physicochemical modulation of artificial redox mediators is further required. Herein, we review and discuss the use of diffusible redox mediators and redox polymer-based approaches in artificial redox-mediating systems, with a focus on photobioelectrocatalysis. The future possibilities of artificial redox mediator system designs are also discussed within the purview of present needs and existing research breadth.

Layer-by-Layer Assembly of Photosystem I and PEDOT:PSS Biohybrid Films for Photocurrent Generation

The design of electrode interfaces to achieve efficient electron transfer to biomolecules is important in many bioelectrochemical processes. Within the field of biohybrid solar energy conversion, constructing multilayered Photosystem I (PSI) protein films that maintain good electronic connection to an underlying electrode has been a major challenge. Previous shortcomings include low loadings, long deposition times, and poor connection between PSI and conducting polymers within composite films. Here, we show that PSI protein complexes can be deposited into monolayers within a 30 min timespan by leveraging the electrostatic interactions between the protein complex and the poly(3,4-ethylenedioxythiophene)-polystyrenesulfonate (PEDOT:PSS) polymer. Further, we follow a layer-by-layer (LBL) deposition procedure to produce up to 9-layer pairs of PSI and PEDOT:PSS with highly reproducible layer thicknesses as well as distinct changes in surface composition. When tested in an electrochemical cell employing ubiquinone-0 as a mediator, the photocurrent performance of the LBL films increased linearly by 83 ± 6 nA/cm² per PSI layer up to 6-layer pairs. The 6-layer pair samples yielded a photocurrent of 414 ± 13 nA/cm², after which the achieved photocurrent diminished with additional layer pairs. The turnover number (TN) of the PSI-PEDOT:PSS LBL assemblies also greatly exceeds that of drop-casted PSI multilayer films, highlighting that the rate of electron collection is improved through the systematic deposition of the protein complexes and conducting polymer. The capability to deposit high loadings of PSI between PEDOT:PSS layers, while retaining connection to the underlying electrode, shows the value in using LBL assembly to produce PSI and PEDOT:PSS bioelectrodes for photoelectrochemical energy harvesting applications.

Enhancement of the Photocurrent of a Single Photosystem I Complex by the Localized Plasmon of a Gold Nanorod

A combination of conductive atomic force microscopy (AFM) and confocal fluorescence microscopy was used to measure photocurrents passing through single trimeric photosytem I (PSI) complexes located in the vicinity of single gold nanorods (AuNRs). Simultaneous excitation of PSI and of the AuNR longitudinal plasmon mode and detection of photocurrents from individual PSI in relation to the position of single AuNRs enable insight into plasmon-induced phenomena that are otherwise inaccessible in ensemble experiments. We have observed photocurrent enhancement by the localized plasmons by a factor of 2.9 on average, with maximum enhancement values of up to 8. Selective excitation of the longitudinal plasmon modes by the polarization of the excitation laser enables controllable switch-on of the photocurrent enhancement. The dependence of the extent of enhancement on the distance between PSI and AuNRs indicates that, apart from the enhancement of absorption, there is an additional enhancement mechanism affecting directly the electron transport process. The present study provides deeper insight into the molecular mechanisms of plasmon-enhanced photocurrents, not only in PSI but also potentially in other systems as well.

Scalable Three-Dimensional Photobioelectrodes Made of Reduced Graphene Oxide Combined with Photosystem I

Photobioelectrodes represent one of the examples where artificial materials are combined with biological entities to undertake semi-artificial photosynthesis. Here, an approach is described that uses reduced graphene oxide (rGO) as an electrode material. This classical 2D material is used to construct a three-dimensional structure by a template-based approach combined with a simple spin-coating process during preparation. Inspired by this novel material and photosystem I (PSI), a biophotovoltaic electrode is being designed and investigated. Both direct electron transfer to PSI and mediated electron transfer via cytochrome c from horse heart as redox protein can be confirmed. Electrode preparation and protein immobilization have been optimized. The performance can be upscaled by adjusting the thickness of the 3D electrode using different numbers of spin-coating steps during preparation. Thus, photocurrents up to ∼14 μA/cm² are measured for 12 spin-coated layers of rGO corresponding to a turnover frequency of 30 e^- PSI^-1 s^-1 and external quantum efficiency (EQE) of 0.07% at a thickness of about 15 μm. Operational stability has been analyzed for several days. Particularly, the performance at low illumination intensities is very promising (1.39 μA/cm² at 0.1 mW/cm² and -0.15 V vs Ag/AgCl; EQE 6.8%).

Fast Photo-Chrono-Amperometry of Photosynthetic Complexes for Biosensors and Electron Transport Studies

Photosynthetic reactions in plants, algae, and cyanobacteria are driven by photosystem I and photosystem II complexes, which specifically reduce or oxidize partner redox biomolecules. Photosynthetic complexes can also bind synthetic organic molecules, which inhibit their photoactivity and can be used both to study the electron transport chain and as herbicides and algicides. Thus, their development, characterization, and sensing bears fundamental and applied interest. Substantial efforts have been devoted to developing photosensors based on photosystem II to detect compounds that bind to the plastoquinone sites of this complex. In comparison, photosystem I based sensors have received less attention and could be used to identify novel substances displaying phytotoxic effects, including those obtained from natural product extracts. We have developed a robust procedure to functionalize gold electrodes with photo- and redox-active photosystem I complexes based on transparent gold and a thiolate self-assembled monolayer, and we have obtained reproducible electrochemical photoresponses. Chronoamperometric recordings have allowed us to measure photocurrents in the presence of the viologen derivative paraquat at concentrations below 100 nM under lock-in operation and a sensor dynamic range spanning six orders of magnitude up to 100 mM. We have modeled their time course to identify the main electrochemical processes and limiting steps in the electron transport chain. Our results allow us to isolate the contributions from photosystem I and the redox mediator, and evaluate photocurrent features (spectral and power dependence, fast transient kinetics) that could be used as a sensing signal to detect other inhibitors and modulators of photosystem I activity.

Photosynthesis Z-Scheme biomimicry: Photosystem I/BiVO4 photo-bioelectrochemical cell for donor-free bias-free electrical power generation

Photo-bioelectrochemical cells that are based on photosynthetic proteins are drawing increased attention for both fundamental and applied research. While novel photosynthetic based systems have been introduced, further optimization in terms of stability and efficiency is required. Photosystem I has been utilized extensively in bioelectronic devices, often in conjugation with viologen moieties which act as electron acceptors. It has been shown previously that a partial reduction of oxygen to H₂O₂ can facilitate damage to proteins hence, limits their long-term activation. Here, we show a newly developed bias-free, donor-free photo-bioelectrochemical system that mimics the natural photosynthetic Z-scheme. Polymethylene blue and polybutyl-viologen were tailored to fit the photosystem I donor and acceptor sides, respectively. Furthermore, we show that by coupling the developed biocathode with a BiVO₄/CoP photoanode, a power output of 25 μW/cm² can be achieved. We further show that our configuration can minimize the damaging effect of H₂O₂ by two different pathways, oxidation at the photoanode or reduction by the polymethylene blue layer at the biocathode.

A new platform for development of photosystem I based thin films with superior photocurrent: TCNQ charge transfer salts derived from ZIF-8

The transmembrane photosynthetic protein complex Photosystem I (PSI) is highly sought after for incorporation into biohybrid photovoltaic devices due to its remarkable photoactive electrochemical properties, chiefly driving charge separation with ∼1 V potential and ∼100% quantum efficiency. In pursuit of these integrated technologies, three factors must be simultaneously tuned, namely, direct redox transfer steps, three-dimensional coordination and stabilization of PSI aggregates, and interfacial connectivity with conductive pathways. Building on our recent successful encapsulation of PSI in the metal-organic framework ZIF-8, herein we use the zinc and imidazole cations from this precursor to form charge transfer complexes with an extremely strong organic electron acceptor, TCNQ. Specifically, the PSI-Zn-H2mim-TCNQ charge transfer salt complex was drop cast on ITO to form dense films. Subsequent voltammetric cycling induced cation exchange and electrochemical annealing of the film was used to enhance electron conductivity giving rise to a photocurrent in the order of 15 μA cm-2. This study paves the way for a myriad of future opportunities for successful integration of this unique class of charge transfer salt complexes with biological catalysts and light harvesters.

Photosystem I Enhances the Efficiency of a Natural, Gel-Based Dye-Sensitized Solar Cell

The photosystem I (PSI) protein complex is known to enhance bioelectrode performance for many liquid-based photoelectrochemical cells. A hydrogel as electrolyte media allows for simpler fabrication of more robust and practical solar cells in comparison to liquid-based devices. This paper reports a natural, gel-based dye-sensitized solar cell that integrates PSI to improve device efficiency. TiO₂-coated FTO slides, dyed by blackberry anthocyanin, act as a photoanode, while a film of PSI deposited onto copper comprises the photocathode. Ascorbic acid (AscH) and 2,6-dichlorophenolindophenol (DCPIP) are the redox mediator couple inside an agarose hydrogel, enabling PSI to produce excess oxidized species near the cathode to improve device performance. A comparison of performance at low pH and neutral pH was performed to test the pH-dependent properties of the AscH/DCPIP couple. Devices at neutral pH performed better than those at lower pH. The PSI film enhanced photovoltage by 75 mV to a total photovoltage of 0.45 V per device and provided a mediator concentration-dependent photocurrent enhancement over non-PSI devices, reaching an instantaneous power conversion efficiency of 0.30% compared to 0.18% without PSI, a 1.67-fold increase. At steady state, power conversion efficiencies for devices with and without PSI were 0.042 and 0.028%, respectively.

Photosensing System Using Photosystem I and Gold Nanoparticle on Graphene Field-Effect Transistor

In this study, a light sensor is fabricated based on photosystem I (PSI) and a graphene field-effect transistor (FET) that detects light at a high quantum yield under ambient conditions. We immobilized PSI on a micrometer-sized graphene FET using Au nanoparticles (AuNPs) and measured the I-V characteristics of the modified graphene FET before and after light irradiation. The source-drain current (I_sd) increased upon illumination, exhibiting a photoresponsivity of 4.8 × 10² A W^-1, and the charge neutrality point of graphene shifted by -12 mV. This system represents the first successful photosensing system based on proteins and a solution-gated graphene FET. The probable mechanism of this negative shift can be explained by the increase in negative charge carriers in graphene induced by a hole trap in the AuNP resulting from electron transfer from the AuNP to PSI. Photoresponses were only observed in the presence of two surface-active agents, n-hexyltrimethylammonium bromide and sodium dodecylbenzenesulfonate, because they caused the formation of a hydrophobic environment on the surface of the graphene. The lipid layer of these agents caused dissociation of ascorbate ions from the graphene sheet, thereby expanding the Debye screening length of the electrolyte solution. The hydrophobic environment above graphene also enhanced hole storage in the AuNP through electron transfer from the AuNP to PSI.

Extended Operational Lifetime of a Photosystem-Based Bioelectrode

The development of bioelectrochemical assemblies for sustainable energy transformation constitutes an increasingly important field of research. Significant progress has been made in the development of semiartificial devices for conversion of light into electrical energy by integration of photosynthetic biomolecules on electrodes. However, sufficient long-term stability of such biophotoelectrodes has been compromised by reactive species generated under aerobic operation. Therefore, meeting the requirements of practical applications still remains unsolved. We present the operation of a photosystem I-based photocathode using an electron acceptor that enables photocurrent generation under anaerobic conditions as the basis for a biodevice with substantially improved stability. A continuous operation lifetime considerably superior to previous reports and at higher light intensities is paving the way toward the potential application of semiartificial energy conversion devices.

Jolly green MOF: confinement and photoactivation of photosystem I in a metal-organic framework

Photosystem I (PSI) is a ∼1000 kDa transmembrane protein that enables photoactivated charge separation with ∼1 V driving potential and ∼100% quantum efficiency during the photosynthetic process. Although such properties make PSI a potential candidate for integration into bio-hybrid solar energy harvesting devices, the grand challenge in orchestrating such integration rests on rationally designed 3D architectures that can organize and stabilize PSI in the myriad of harsh conditions in which it needs to function. The current study investigates the optical response and photoactive properties of PSI encapsulated in a highly stable nanoporous metal-organic framework (ZIF-8), denoted here as PSI@ZIF-8. The ZIF-8 framework provides a unique scaffold with a robust confining environment for PSI while protecting its precisely coordinated chlorophyll networks from denaturing agents. Significant blue shifts in the fluorescence emissions from UV-vis measurements reveal the successful confinement of PSI in ZIF-8. Pump-probe spectroscopy confirms the photoactivity of the PSI@ZIF-8 composites by revealing the successful internal charge separation and external charge transfer of P₇₀₀ ⁺ and F_B ^- even after exposure to denaturing agents and organic solvents. This work provides greater fundamental understanding of confinement effects on pigment networks, while significantly broadening the potential working environments for PSI-integrated bio-hybrid materials.

Engineering of supramolecular photoactive protein architectures: the defined co-assembly of photosystem I and cytochrome c using a nanoscaled DNA-matrix

The engineering of renewable and sustainable protein-based light-to-energy converting systems is an emerging field of research. Here, we report on the development of supramolecular light-harvesting electrodes, consisting of the redox protein cytochrome c working as a molecular scaffold as well as a conductive wiring network and photosystem I as a photo-functional matrix element. Both proteins form complexes in solution, which in turn can be adsorbed on thiol-modified gold electrodes through a self-assembly mechanism. To overcome the limited stability of self-grown assemblies, DNA, a natural polyelectrolyte, is used as a further building block for the construction of a photo-active 3D architecture. DNA acts as a structural matrix element holding larger protein amounts and thus remarkably improving the maximum photocurrent and electrode stability. On investigating the photophysical properties, this system demonstrates that effective electron pathways have been created.

Elucidating the role of methyl viologen as a scavenger of photoactivated electrons from photosystem I under aerobic and anaerobic conditions

We present electrochemical investigations into the role of dissolved O₂ in electrolyte solutions in scavenging photoactivated electrons from photosystem I (PS I) while using methyl viologen (MV²⁺) as the redox mediator.

Energy transfer cascade in bio-inspired chlorophyll-a/polyacrylamide hydrogel: towards a new class of biomimetic solar cells

Efficient solar energy harvesting in natural photosystem inspired chlorophyll-a/hydrogel based soft, simple system, revealing the effect of coherence-dephasing interpaly.

Electrochemical preparation of Photosystem I-polyaniline composite films for biohybrid solar energy conversion

In this work, we report for the first time the entrapment of the biomolecular supercomplex Photosystem I (PSI) within a conductive polymer network of polyaniline via electrochemical copolymerization. Composite polymer-protein films were prepared on gold electrodes through potentiostatic electropolymerization from a single aqueous solution containing both aniline and PSI. This study demonstrates the controllable integration of large membrane proteins into rapidly prepared composite films, the entrapment of such proteins was observed through photoelectrochemical analysis. PSI's unique function as a highly efficient biomolecular photodiode generated a significant enhancement in photocurrent generation for the PSI-loaded polyaniline films, compared to pristine polyaniline films, and dropcast PSI films. A comprehensive study was then performed to separately evaluate film thickness and PSI concentration in the initial polymerization solution and their effects on the net photocurrent of this novel material. The best performing composite films were prepared with 0.1 μM PSI in the polymerization solution and deposited to a film thickness of 185 nm, resulting in an average photocurrent density of 5.7 μA cm(-2) with an efficiency of 0.005%. This photocurrent output represents an enhancement greater than 2-fold over bare polyaniline films and 200-fold over a traditional PSI multilayer film of comparable thickness.

Photocurrent generation in diamond electrodes modified with reaction centers

Photoactive reaction centers (RCs) are protein complexes in bacteria able to convert sunlight into other forms of energy with a high quantum yield. The photostimulation of immobilized RCs on inorganic electrodes result in the generation of photocurrent that is of interest for biosolar cell applications. This paper reports on the use of novel electrodes based on functional conductive nanocrystalline diamond onto which bacterial RCs are immobilized. A three-dimensional conductive polymer scaffold grafted to the diamond electrodes enables efficient entrapment of photoreactive proteins. The electron transfer in these functional diamond electrodes is optimized through the use of a ferrocene-based electron mediator, which provides significant advantages such as a rapid electron transfer as well as high generated photocurrent. A detailed discussion of the generated photocurrent as a function of time, bias voltage, and mediators in solution unveils the mechanisms limiting the electron transfer in these functional electrodes. This work featuring diamond-based electrodes in biophotovoltaics offers general guidelines that can serve to improve the performance of similar devices based on different materials and geometries.

Linker-free deposition and adhesion of Photosystem I onto nanostructured TiO2 for biohybrid photoelectrochemical cells

Photosystem I (PSI) from oxygenic photosynthetic organisms is an attractive sensitizer for nano-biohybrid solar cells as it has a combined light-harvesting and reaction center in one protein complex and operates at a quantum yield close to one in biological systems. Using a linker-free deposition technique enabled by an electrospray system, PSI was coupled to 1-D nanostructured titanium dioxide thin films to fabricate an electrode for a photoelectrochemical cell. After deposition, the surfactant in the PSI aggregate was dissolved in the surfactant-free electrolyte, ensuring that partly hydrophobic PSI was not resuspended and stayed in contact with titanium dioxide. A maximum current density of 4.15 mA cm(-2) was measured after 10 min of electrospray deposition, and this is the highest current density reported so far for PSI-based photoelectrochemical cells. The high current is attributed to 1D nanostructure of titanium dioxide and orientation of the PSI onto the surface, which allows easy transfer of electrons.

Sortase-mediated ligation of PsaE-modified photosystem I from Synechocystis sp. PCC 6803 to a conductive surface for enhanced photocurrent production on a gold electrode

Sortase-mediated ligation was used to attach the photosystem I (PSI) complex from Synechocystis sp. PCC 6803 in a preferential orientation to enhance photoinduced electron flow to a conductive gold surface. Ideally, this method can result in a uniform monolayer of protein, covalently bound unidirectionally to the electrode surface. The exposed C-termini of the psaE subunits of the PSI trimer were targeted to contain an LPETG-sortase recognition sequence to increase noncompeting electron transfer by uniformly orienting the PSI stromal side proximal to the surface. Surface characterization with atomic force microscopy suggested that monolayer formation and optimal surface coverage occurred when the gold surfaces were incubated with peptide at 100 to 500 μM concentrations. When photochronoamperometry with potassium ferrocyanide and ferricyanide as redox mediators was used, photocurrents in the range of 100 to 200 nA/cm(2) were produced, which is an improvement over other attachment techniques for photosystem monolayers that produce approximately 100 nA/cm(2) or less. This work demonstrated that sortase-mediated ligation aided in the control of PSI orientation on modified gold surfaces with a distribution of 94% stromal side proximal and 6% lumenal side proximal to the surface for current-producing PSI.

Photoelectrochemistry of photosystem I bound in nafion

Developing a solid state Photosystem I (PSI) modified electrode is attractive for photoelectrochemical applications because of the quantum yield of PSI, which approaches unity in the visible spectrum. Electrodes are constructed using a Nafion film to encapsulate PSI as well as the hole-scavenging redox mediator Os(bpy)2Cl2. The photoactive electrodes generate photocurrents of 4 μA/cm(2) when illuminated with 1.4 mW/cm(2) of 676 nm band-pass filtered light. Methyl viologen (MV(2+)) is present in the electrolyte to scavenge photoelectrons from PSI in the Nafion film and transport charges to the counter electrode. Because MV(2+) is positively charged in both reduced and oxidized states, it is able to diffuse through the cation permeable channels of Nafion. Photocurrent is produced when the working electrode is set to voltages negative of the Os(3+)/Os(2+) redox potential. Charge transfer through the Nafion film and photohole scavenging at the PSI luminal surface by Os(bpy)2Cl2 depends on the reduction of Os redox centers to Os(2+) via hole scavenging from PSI. The optimal film densities of Nafion (10 μg/cm(2) Nafion) and PSI (100 μg/cm(2) PSI) are determined to provide the highest photocurrents. These optimal film densities force films to be thin to allow the majority of PSI to have productive electrical contact with the backing electrode.

Two-dimensional protein crystals for solar energy conversion

Two-dimensional photosynthetic protein crystals provide a high density of aligned reaction centers. We reconstitute the robust light harvesting protein Photosystem I into a 2D crystal with lipids and integrate the crystals into a photo-electrochemical device. A 4-fold photocurrent enhancement is measured by incorporating conjugated oligoelectrolytes to form a supporting conductive bilayer in the device which produces a high photocurrent of ∼600 μA per mg PSI deposited.

Photosystem I protein films at electrode surfaces for solar energy conversion

Over the course of a few billion years, nature has developed extraordinary nanomaterials for the efficient conversion of solar energy into chemical energy. One of these materials, photosystem I (PSI), functions as a photodiode capable of generating a charge separation with nearly perfect quantum efficiency. Because of the favorable properties and natural abundance of PSI, researchers around the world have begun to study how this protein complex can be integrated into modern solar energy conversion devices. This feature article describes some of the recent materials and methods that have led to dramatic improvements (over several orders of magnitude) in the photocurrents and photovoltages of biohybrid electrodes based on PSI, with an emphasis on the research activities in our laboratory.

Growing green electricity: progress and strategies for use of photosystem I for sustainable photovoltaic energy conversion

Oxygenic photosynthesis is driven via sequential action of Photosystem II (PSII) and (PSI)reaction centers via the Z-scheme. Both of these pigment-membrane protein complexes are found in cyanobacteria, algae, and plants. Unlike PSII, PSI is remarkably stable and does not undergo limiting photo-damage. This stability, as well as other fundamental structural differences, makes PSI the most attractive reaction centers for applied photosynthetic applications. These applied applications exploit the efficient light harvesting and high quantum yield of PSI where the isolated PSI particles are redeployed providing electrons directly as a photocurrent or, via a coupled catalyst to yield H₂. Recent advances in molecular genetics, synthetic biology, and nanotechnology have merged to allow PSI to be integrated into a myriad of biohybrid devices. In photocurrent producing devices, PSI has been immobilized onto various electrode substrates with a continuously evolving toolkit of strategies and novel reagents. However, these innovative yet highly variable designs make it difficult to identify the rate-limiting steps and/or components that function as bottlenecks in PSI-biohybrid devices. In this study we aim to highlight these recent advances with a focus on identifying the similarities and differences in electrode surfaces, immobilization/orientation strategies, and artificial redox mediators. Collectively this work has been able to maintain an annual increase in photocurrent density (Acm⁻²) of ~10-fold over the past decade. The potential drawbacks and attractive features of some of these schemes are also discussed with their feasibility on a large-scale. As an environmentally benign and renewable resource, PSI may provide a new sustainable source of bioenergy. This article is part of a special issue entitled: photosynthesis research for sustainability: keys to produce clean energy.

Advanced unidirectional photocurrent generation via cytochrome c as reaction partner for directed assembly of photosystem I

Engineering biohybrid photodiodes using surface-fixed cytochrome c as scaffold for efficiently connecting photosystem I with electrodes in 3D protein architectures.

Application of peptide gemini surfactants as novel solubilization surfactants for photosystems I and II of cyanobacteria

We designed novel peptide gemini surfactants (PG-surfactants), DKDKC12K and DKDKC12D, which can solubilize Photosystem I (PSI) of Thermosynecoccus elongatus and Photosystem II (PSII) of Thermosynecoccus vulcanus in an aqueous buffer solution. To assess the detailed effects of PG-surfactants on the original supramolecular membrane protein complexes and functions of PSI and PSII, we applied the surfactant exchange method to the isolated PSI and PSII. Spectroscopic properties, light-induced electron transfer activity, and dynamic light scattering measurements showed that PSI and PSII could be solubilized not only with retention of the original supramolecular protein complexes and functions but also without forming aggregates. Furthermore, measurement of the lifetime of light-induced charge-separation state in PSI revealed that both surfactants, especially DKDKC12D, displayed slight improvement against thermal denaturation below 60 °C compared with that using β-DDM. This degree of improvement in thermal resistance still seems low, implying that the peptide moieties did not interact directly with membrane protein surfaces. By conjugating an electron mediator such as methyl viologen (MV(2+)) to DKDKC12K (denoted MV-DKDKC12K), we obtained derivatives that can trap the generated reductive electrons from the light-irradiated PSI. After immobilization onto an indium tin oxide electrode, a cathodic photocurrent from the electrode to the PSI/MV-DKDKC12K conjugate was observed in response to the interval of light irradiation. These findings indicate that the PG-surfactants DKDKC12K and DKDKC12D provide not only a new class of solubilization surfactants but also insights into designing other derivatives that confer new functions on PSI and PSII.

Covalent immobilization of oriented photosystem II on a nanostructured electrode for solar water oxidation

Photosystem II (PSII) offers a biological and sustainable route of photochemical water oxidation to O2 and can provide protons and electrons for the generation of solar fuels, such as H2. We present a rational strategy to electrostatically improve the orientation of PSII from a thermophilic cyanobacterium, Thermosynechococcus elongatus , on a nanostructured indium tin oxide (ITO) electrode and to covalently immobilize PSII on the electrode. The ITO electrode was modified with a self-assembled monolayer (SAM) of phosphonic acid ITO linkers with a dangling carboxylate moiety. The negatively charged carboxylate attracts the positive dipole on the electron acceptor side of PSII via Coulomb interactions. Covalent attachment of PSII in its electrostatically improved orientation to the SAM-modified ITO electrode was accomplished via an amide bond to further enhance red-light-driven, direct electron transfer and stability of the PSII hybrid photoelectrode.