Enhanced stability of low fouling zwitterionic polymer brushes in seawater with diblock architecture

Novel Antifouling Coatings by Zwitterionic Silica Grafting on Glass Substrates

Zwitterionic silica coatings for surface functionalization are greatly prominent because of their simple and fast preparation, high availability, and effective antifouling properties. In this work, two zwitterionic sulfobetaine silane coatings, i.e., mono-SBSi and tris-SBSi, were deposited on glass surfaces and tested for antifouling of biological material and biofilm using human cancer cell and seawater, respectively. The used zwitterionic precursors mono-SBSi and tris-SBSi differ by the number of hydrolyzable silane groups: mono-SBSi contains one trimethoxysilane group, whereas tris-SBSi contains three of these functions. First, X-ray photoelectron spectroscopy indicates the successful grafting of zwitterionic coatings onto a glass surface. Characterization using atomic force microscopy shows the different morphologies and roughness of the two coatings. The glass surface became more hydrophilic after the grafting of zwitterionic coatings than the bare glass substrate. The antifouling properties of two coatings were evaluated via human cancer cell adsorption. Interestingly, the tris-SBSi coating displays a significantly lower level of cell adsorption compared to that of both mono-SBSi coating and the non-modified control surface. The same trend was observed for biofilm formation in seawater. Finally, the toxicity of mono-SBSi and tris-SBSi coatings was evaluated on zebrafish embryos, indicating the good biocompatibility of both coatings. Our results indicate interesting antifouling properties of zwitterionic coatings. The chemical constitution of the used precursor has an impact on the antifouling properties of the formed coating: the tris-SBSi-based zwitterionic silica coatings display improved antifouling properties compared to those of the mono-SBSi-based coating. Besides, the use of trisilylated precursors should result in the formation of more resistant and robust coatings due to the higher number of grafting functions. For all these reasons, we anticipate that tris-SBSi coatings will open new perspectives for antifouling applications for biological environments and implants.

Biomimetic redox-responsive smart coatings with resistance-release functions for reverse osmosis membranes

Membrane fouling induces catastrophic loss of separation performance and seriously restricts the applications of reverse osmosis (RO) membranes. Inspired by the mussel structure, polydopamine (PDA) and cystamine molecules (CA) with excellent anti-fouling properties were used to prepare accessible, biocompatible, and redox-responsive coatings for RO membranes. The PDA/CA-coated RO membranes exhibit a superior water flux of 65 L m-2 h-1 with a favourable NaCl rejection exceeding 99%. The water permeability through the PDA/CA-coated membrane is much higher than that of most membranes with similar rejection rates. Due to the formed protective hydration layers by PDA/CA coatings, anti-fouling properties against proteins, polysaccharides and surfactants were evaluated separately, and ultralow fouling properties were demonstrated. Moreover, the disulfide linkages in CA molecules can cleave in a reducing environment, yielding the degradation of PDA/CA coatings, thereby removing the foulants deposited on the coatings. The degradation endows the coated membranes with satisfying longtime anti-fouling properties, where the flux recovery reaches up to 90%. The construction of redox-responsive smart coatings not only provided a promising route to alleviate membrane fouling but can also be upscaled for use in numerous practical applications like sensors, medical devices, and drug delivery.

Colloidal Rod-Like Particles with Temperature-Driven Tunable Interactions

Temperature-sensitive rod-like colloidal particles were synthesized by grafting a temperature-responsive polymer, poly(2-(dimethylamino)ethyl methacrylate) (PDMA), on the surface of high aspect ratio silica rods by surface-initiated atom transfer radical polymerization. The stability of the grafted polymer on the surface of the particles in aqueous solutions was found to deteriorate with time, leading to a gradual decrease of the polymer content of the hybrid colloids, which was attributed to the mechanically activated hydrolysis of the labile bonds at the polymer-silica interface. The polymer degrafting was significantly suppressed by first growing a hydrophobic poly(methyl methacrylate) block onto the particle surface to act as a barrier layer for the penetration of water molecules at the polymer-particle interface, followed by chain-extension with the hydrophilic PDMA chains. Dynamic light scattering, microscopy, and rheological measurements revealed that the PDMA block conferred a temperature-responsive behavior to the rod-like particles, which formed aggregates at temperatures above the lower critical solution temperature (LCST) of the polymer. However, in contrast to their spherical counterparts, the polymer-grafted rod-like particles did not exhibit complete thermo-reversibility upon lowering the solution temperature below the LCST of PDMA, which was reflected by different values of the diffusion coefficient for the heating and cooling cycles, indicating an irreversible rod particle aggregation upon increasing the temperature.

Temperature-Responsive Polymer Brush Coatings for Advanced Biomedical Applications

Modern biomedical technologies predict the application of materials and devices that not only can comply effectively with specific requirements, but also enable remote control of their functions. One of the most prospective materials for these advanced biomedical applications are materials based on temperature-responsive polymer brush coatings (TRPBCs). In this review, methods for the fabrication and characterization of TRPBCs are summarized, and possibilities for their application, as well as the advantages and disadvantages of the TRPBCs, are presented in detail. Special attention is paid to the mechanisms of thermo-responsibility of the TRPBCs. Applications of TRPBCs for temperature-switchable bacteria killing, temperature-controlled protein adsorption, cell culture, and temperature-controlled adhesion/detachment of cells and tissues are considered. The specific criteria required for the desired biomedical applications of TRPBCs are presented and discussed.

Entropy-Enhanced Mechanochemical Activation for Thermal Degrafting of Surface-Tethered Dry Polystyrene Brushes

Dry polymer brushes have attracted great attention because of their potential utility in regulating interface properties. However, it is still unknown whether dry polymer brushes will exhibit degrafting behavior as a result of thermal annealing. Herein, a study of the conformational entropy effect on thermal degrafting of dry polystyrene (PS) brushes is presented. For PS brushes with an initial grafting density (σ_pⁱⁿⁱ) of 0.61 nm^-2, degrafting behavior was observed at 393 K, and the equilibrium σ_p was approximately 0.14 nm^-2 at 413 K. However, for brushes with σ_pⁱⁿⁱ ≤ 0.14 nm^-2, thermal degrafting was not observed even if the temperature was increased to 453 K. Furthermore, we found that the degrafting rate was faster for PS brushes with higher σ_pⁱⁿⁱ and higher molecular weights when σ_pⁱⁿⁱ > 0.14 nm^-2. Our findings confirmed that degrafting is a mechanochemical activation process driven by tension imposed on bonds that anchor the chains to the surface, and the process is amplified by conformational entropy.

Investigation of N-Substituted Morpholine Structures in an Amphiphilic PDMS-Based Antifouling and Fouling-Release Coating

Biofouling is a major disruptive process affecting the fuel efficiency and durability of maritime vessel coatings. Previous research has shown that amphiphilic coatings consisting of a siloxane backbone functionalized with hydrophilic moieties are effective marine antifouling and fouling-release materials. Poly(ethylene glycol) (PEG) has been the primary hydrophilic component used in such systems. Recently, the morpholine group has emerged as a promising compact alternative in antifouling membranes but is yet to be studied against marine foulants. In this work, the use of morpholine moieties to generate amphiphilicity in a poly(dimethylsiloxane) (PDMS)-based antifouling and fouling-release coating was explored. Two separate coating sets were investigated. The first set examined the incorporation of an N-substituted morpholine amine, and while these coatings showed promising fouling-release properties for Ulva linza, they had unusually high settlement of spores compared to controls. Based on those results, a second set of materials was synthesized using an N-substituted morpholine amide to probe the source of the high settlement and was found to significantly improve antifouling performance. Both coating sets included PEG controls with varying lengths to compare the viability of the morpholine structures as alternative hydrophilic groups. Surfaces were evaluated through a combination of bubble contact angle goniometry, profilometry, X-ray photoelectron spectroscopy (XPS), and marine bioassays against two soft fouling species, U. linza and Navicula incerta, known to have different adhesion characteristics.

Synthetic strategies to enhance the long-term stability of polymer brush coatings

High-density, end-anchored macromolecules that form so-called polymer brushes are popular components of bio-inspired surface coatings. In a bio-memetic approach, they have been utilized to reduce friction, repel contamination and control...

Polyelectrolytes as Building Blocks for Next-Generation Membranes with Advanced Functionalities

The global society is in a transition, where dealing with climate change and water scarcity are important challenges. More efficient separations of chemical species are essential to reduce energy consumption and to provide more reliable access to clean water. Here, membranes with advanced functionalities that go beyond standard separation properties can play a key role. This includes relevant functionalities, such as stimuli-responsiveness, fouling control, stability, specific selectivity, sustainability, and antimicrobial activity. Polyelectrolytes and their complexes are an especially promising system to provide advanced membrane functionalities. Here, we have reviewed recent work where advanced membrane properties stem directly from the material properties provided by polyelectrolytes. This work highlights the versatility of polyelectrolyte-based membrane modifications, where polyelectrolytes are not only applied as single layers, including brushes, but also as more complex polyelectrolyte multilayers on both porous membrane supports and dense membranes. Moreover, free-standing membranes can also be produced completely from aqueous polyelectrolyte solutions allowing much more sustainable approaches to membrane fabrication. The Review demonstrates the promise that polyelectrolytes and their complexes hold for next-generation membranes with advanced properties, while it also provides a clear outlook on the future of this promising field.

Biomimetic surface coatings for marine antifouling: Natural antifoulants, synthetic polymers and surface microtopography

Marine biofouling is a ubiquitous problem that accompanies human marine activities and marine industries. It exerts detrimental impacts on the economy, environment, ecology, and safety. Traditionally, mainstream approaches utilize metal ions to prevent biological contamination, but this also leads to environmental pollution and damage to the ecosystem. Efficient and environmentally friendly coatings are urgently needed to prevent marine devices from biofouling. Since nature is always the best teacher for humans, it offers us delightful thoughts on the research and development of high-efficiency, broad-spectrum and eco-friendly antifouling coatings. In this work, we focus on the research frontier of marine antifouling coatings from a bionic perspective. Enlightened by three distinctive dimensions of bionics: chemical molecule bionic, physiological mechanism bionic, and physical structure bionic, the research status of three main bioinspired strategies, which are natural antifoulants, bioinspired polymeric antifouling coatings, and biomimetic surface microtopographies, respectively, are demonstrated. The antifouling mechanisms are further interpreted based on biomimetic comprehension. The main fabrication methods and antifouling performances of these coatings are presented along with their advantages and drawbacks. Finally, the challenges are summarized, and future research prospects are proposed. It is believed that biomimetic antifouling strategies will contribute to the development of nontoxic antifouling techniques with exceptional repellency and stability.

Bioinert and Lubricious Surfaces by Macromolecular Design

The modification of a variety of biomaterials and medical devices often encompasses the generation of biopassive and lubricious layers on their exposed surfaces. This is valid when the synthetic supports are required to integrate within physiological media without altering their interfacial composition and when the minimization of shear stress prevents or reduces damage to the surrounding environment. In many of these cases, hydrophilic polymer brushes assembled from surface-interacting polymer adsorbates or directly grown by surface-initiated polymerizations (SIP) are chosen. Although growing efforts by polymer chemists have been focusing on varying the composition of polymer brushes in order to attain increasingly bioinert and lubricious surfaces, the precise modulation of polymer architecture has simultaneously enabled us to substantially broaden the tuning potential for the above-mentioned properties. This feature article concentrates on reviewing this latter strategy, comparatively analyzing how polymer brush parameters such as molecular weight and grafting density, the application of block copolymers, the introduction of branching and cross-links, or the variation of polymer topology beyond the simple, linear chains determine highly technologically relevant properties, such as biopassivity and lubrication.

Polymer Brush Friction in Cylindrical Geometries

Polymer brushes are outstanding lubricants that can strongly reduce wear and friction between surfaces in sliding motion. In recent decades, many researchers have put great effort in obtaining a clear understanding of the origin of the lubricating performance of these brushes. In particular, molecular dynamics simulations have been a key technique in this scientific journey. They have given us a microscopic interpretation of the tribo-mechanical response of brushes and have led to the prediction of their shear-thinning behavior, which has been shown to agree with experimental observations. However, most studies so far have focused on parallel plate geometries, while the brush-covered surfaces might be highly curved in many applications. Here, we present molecular dynamics simulations that are set up to study the friction for brushes grafted on the exterior of cylinders that are moving inside larger cylinders that bear brushes on their interior. Our simulations show that the density distributions for brushes on the interior or exterior of these cylinders are qualitatively different from the density profiles of brushes on flat surfaces. In agreement with theoretical predictions, we find that brushes on the exterior of cylinders display a more gradual decay, while brushes on the interior of cylinders becomes denser compared to flat substrates. When motion is imposed, the density profiles for cylinder-grafted brushes adapt qualitatively differently to the shear motion than observed for the parallel plate geometry: the zone where brushes overlap moves away from its equilibrium position. Surprisingly, and despite all these differences, we observe that the effective viscosity is independent of the radius of the brush-grafted cylinders. The reason for this is that the viscosity is determined by the overlap between the brushes, which turns out to be insensitive to the exact density profiles. Our results provide a microscopic interpretation of the friction mechanism for polymer brushes in cylindrical geometries and will aid the design of effective lubricants for these systems.

Nonfreezable Water and Polymer Swelling Control the Marine Antifouling Performance of Polymers with Limited Hydrophilic Content

Zwitterionic chemical groups have well-documented resistance to marine fouling species when presented as homogeneous polymer brushes. These model formulations are not, however, suitable for practical fouling-control applications. It is presently unknown if a uniform film of zwitterions is required to elicit nonfouling character via the binding of interfacial water or if the incorporation of zwitterionic functionality into a more practical bulk polymer system will suffice. Here, copolymers of n-butyl methacrylate were synthesized with low incorporation levels (up to 20 mol %) of hydrophilic functionality, including zwitterionic moieties. Their antifouling (AF) properties were evaluated using barnacle cyprids (Balanus improvisus), diatom cells (Navicula incerta), and a multispecies biofilm. The laboratory assays revealed higher resistance of ionic copolymers toward cyprid settlement, which was attributed to their swelling and the presence of nonfreezable water molecules bound tightly to the polymer chains. Additionally, cells of N. incerta and the multispecies biofilm were removed more effectively on polymers containing sulfobetaine methacrylate and sulfopropyl methacrylate moieties. The results indicate that the presence of tightly bound interfacial water is not limited to model systems of pure hydrophilic homopolymers, but that this mechanism can also reduce the settlement and adhesion of fouling species via bulk copolymer systems with limited hydrophilic content. The swelling of polymers with hydrophilic content may also contribute to their AF efficacy, and such materials may therefore represent a route to translation of the well-documented nonfouling character of zwitterions into practical, industrially relevant coating formulations.

Polyzwitterionic Hydrogels in Engines Based on the Antipolyelectrolyte Effect and Driven by the Salinity Gradient

In this paper, we propose and investigate an original approach to energy conversion based on polyzwitterionic hydrogels, which exhibit an antipolyelectrolyte effect that enables them to swell in salt water and shrink in water of a different (i.e., desalinated water) salinity. The swelling and shrinking processes run cyclically and can move a piston up or down reversibly, thus transforming the antipolyelectrolyte effect into a mechanical force based on the salinity gradient. This phenomenon makes polyzwitterionic hydrogels suitable for use in a smart, polymeric engine. We apply this approach to investigate energy recovery from a polysulfobetaine-based hydrogel. The cross-linking density, external load, particle size, and repeatability of energy recoverability of hydrogels are examined. The maximum energy recovery from 0.4 g of hydrogel in feed (calculated based on dry form) of 102 mJ/kg was obtained by a hydrogel with a 3% cross-linking density, a 200-300 μm particle size, and 100 g external load. Excellent reproducibility of engine cycles was achieved over 10 cycles. This concept is complementary to the osmotic engine concept based on a polyelectrolyte hydrogel. In addition, polyzwitterionic materials have become a benchmark material for preventing biofouling, and the swelling properties of such materials can be further modulated and tuned.

Polymer-Based Marine Antifouling and Fouling Release Surfaces: Strategies for Synthesis and Modification

In marine industries, the accumulation of organic matter and marine organisms on ship hulls and instruments limits performance, requiring frequent maintenance and increasing fuel costs. Current coatings technology to combat this biofouling relies heavily on the use of toxic, biocide-containing paints. These pose a serious threat to marine ecosystems, affecting both target and nontarget organisms. Innovation in the design of polymers offers an excellent platform for the development of alternatives, but the creation of a broad-spectrum, nontoxic material still poses quite a hurdle for researchers. Surface chemistry, physical properties, durability, and attachment scheme have been shown to play a vital role in the construction of a successful coating. This review explores why these characteristics are important and how recent research accounts for them in the design and synthesis of new environmentally benign antifouling and fouling release materials.

Degradable and Thermosensitive Microgels Synthesized via Simultaneous Quaternization and Siloxane Condensation

Degradable and thermosensitive microgels were successfully prepared via simultaneous quaternization and siloxane condensation during surfactant-free emulsion polymerization, with N-vinylcaprolactam as the main monomer and 1-vinylimidazole (VIM) as the comonomer, in the presence of (3-bromopropyl)trimethoxysilane (BPTMOS). The formation mechanism of cross-linking network was attributed to the hydrolysis and condensation of the methoxysilyl groups of BPTMOS and the quaternization of imidazole moiety of VIM by the bromine group of BPTMOS, leading to the microgels. The microgels were spherical in shape with a narrow size distribution, stable in an acidic buffer solution, but degradable in neutral and alkaline solutions. The presence of quaternized imidazolium in the same chain segment of Si-O-Si cross-linking points promoted the decomposition of Si-O-Si bonds and hence the degradation of the microgels. The obtained microgels could load and release the model drug, doxorubicin. The size, thermosensitivity, stability, degradation rate, and drug release behavior of the resultant microgels could be tuned by controlling the cross-linking degree, chemical composition, and degradation medium.

Oxidation-Mediated, Zwitterionic Polydopamine Coatings for Marine Antifouling Applications

We synthesized a zwitterionic dopamine derivative ( ZW-DOPA) containing both catechol and amine groups, and we demonstrated an excellent marine antifouling surface by controlling the oxidation of ZW-DOPA. The oxidation was mediated by the deprotonation of catechol or the addition of an oxidant (ammonium persulfate (AP) or sodium periodate (NaIO₄)). The oxidation and subsequent molecular transformation of ZW-DOPA was investigated over time by UV-vis spectroscopy. Among the different oxidation conditions tested, NaIO₄-induced ZW-DOPA coating was the most efficient and successfully formed on various substrates, such as titanium dioxide, stainless steel, and nylon. Compared with uncoated substrates, ZW-DOPA-coated substrates showed high resistance to marine diatom adhesion. Considering the ease of use and substrate independence of the ZW-DOPA coating, this method shows promise as a basis for inhibiting marine fouling on a variety of substrates used in the marine industry and aquatic environments.

Design and characterization of ultrastable, biopassive and lubricious cyclic poly(2-alkyl-2-oxazoline) brushes

Bilayer films featuring cyclic, poly(2-alkyl-2-oxazoline) brush interfaces display excellent biopassivity, lubrication and long-term stability in chemically harsh aqueous environments.

Superhydrophilic co-polymer coatings on denture surfaces reduce Candida albicans adhesion-An in vitro study

OBJECTIVE

In this study, we aimed to investigate denture-base-resin coatings prepared with a crosslinkable co-polymer containing sulfobetaine methacrylamide (SBMAm) and the relationship between their surface characteristics and the initial adhesion of Candida albicans (C. albicans).

METHODS

Acrylic resin discs were coated with co-polymers containing various concentrations of SBMAm and N,N'-(4,7,10-trioxa-1,13-tridecadiamine) diacrylamide (JDA) as crosslinking agent. Uncoated discs were used as controls. An acquired pellicle was formed on each disc using artificial saliva, and the discs were immersed in a suspension of C. albicans (JCM2085) cells. After incubation, tetrazolium salt (XTT-reduction) and colony forming unit (CFU) assays were performed and the morphogenesis of C. albicans was examined using scanning electron microscopy (SEM). The surface roughness, film thickness, and the water contact angle of each disc surface were measured.

RESULTS

All coating groups showed significantly lower amounts of adhered C. albicans in the XTT-reduction and CFU assays than the control, confirmed by the SEM images. Many wrinkle structures were observed on the surfaces coated with co-polymers containing more than 30% SBMAm. There were no significant differences in surface roughness among all groups. The co-polymer films on the coated discs were less than 5.0 μm in thickness, and these surfaces exhibited significantly lower mean water contact angles than the control.

CONCLUSION

Crosslinkable co-polymers containing SBMAm can enhance the hydrophilicity of the surface of denture-base resins and reduce the initial adhesion of C. albicans.

Polymer Thin Films and Surface Modification by Chemical Vapor Deposition: Recent Progress

Chemical vapor deposition (CVD) polymerization uses vapor phase monomeric reactants to synthesize organic thin films directly on substrates. These thin films are desirable as conformal surface engineering materials and functional layers. The facile tunability of the films and their surface properties allow successful integration of CVD thin films into prototypes for applications in surface modification, device fabrication, and protective films. CVD polymers also bridge microfabrication technology with chemical and biological systems. Robust coatings can be achieved via CVD methods as antifouling, anti-icing, and antihydrate surfaces, as well as stimuli-responsive or biocompatible polymers and novel nanostructures. Use of low-energy input, modest vacuum, and room-temperature substrates renders CVD polymerization compatible with thermally sensitive substrates and devices. Compared with solution-based methods, CVD is particularly useful for insoluble materials, such as electrically conductive polymers and controllably crosslinked networks, and has the potential to reduce environmental, health, and safety impacts associated with solvents. This review discusses the relevant background and selected applications of recent advances by two methods that display and use the high retention of the organic functional groups from their respective monomers, initiated CVD (iCVD) and oxidative CVD (oCVD) polymerization.

Modification of Nanoporous Silicon Nitride with Stable and Functional Organic Monolayers

This study describes the formation of functional organic monolayers on thin, nanoporous silicon nitride membranes. We demonstrate that the vapor-phase carbene insertion into the surface C-H bonds can be used to form sub-5 nm molecular coatings on nanoporous materials, which can be further modified with monolayers of polyethylene glycol (PEG) molecules. We investigate composition, thickness, and stability of the functionalized monolayers and the changes in the membrane permeability and pore size distribution. We show that, due to the low coating thickness (~7 nm), the functionalized membrane retains 80% of the original gas permeance and 40% of the original hydraulic permeability. We also show that the carbene/PEG functionalization is hydrolytically stable for up to 48 h of exposure to water and that it can suppress nonspecific adsorption of the proteins BSA and IgG. Our results suggest that the vapor-phase carbenylation can be used as a complementary technology to the traditional self-assembly and polymer brush chemistries in chemical functionalization of nanoporous materials, which are limited in their ability to serve as stable coatings that do not occlude nanomembrane pores.

A brief review of recent developments in the designs that prevent bio-fouling on silicon and silicon-based materials

Silicon and silicon-based materials are essential to our daily life. They are widely used in healthcare and manufacturing. However, silicon and silicon-based materials are susceptible to bio-fouling, which is of great concern in numerous applications. To date, interdisciplinary research in surface science, polymer science, biology, and engineering has led to the implementation of antifouling strategies for silicon-based materials. However, a review to discuss those antifouling strategies for silicon-based materials is lacking. In this article, we summarized two major approaches involving the functionalization of silicon and silicon-based materials with molecules exhibiting antifouling properties, and the fabrication of silicon-based materials with nano- or micro-structures. Both approaches lead to a significant reduction in bio-fouling. We critically reviewed the designs that prevent fouling due to proteins, bacteria, and marine organisms on silicon and silicon-based materials. Graphical abstractStrategies used in the designs that prevent bio-fouling on silicon and silicon-based materials.

Surface-Initiated Controlled Radical Polymerization: State-of-the-Art, Opportunities, and Challenges in Surface and Interface Engineering with Polymer Brushes

The generation of polymer brushes by surface-initiated controlled radical polymerization (SI-CRP) techniques has become a powerful approach to tailor the chemical and physical properties of interfaces and has given rise to great advances in surface and interface engineering. Polymer brushes are defined as thin polymer films in which the individual polymer chains are tethered by one chain end to a solid interface. Significant advances have been made over the past years in the field of polymer brushes. This includes novel developments in SI-CRP, as well as the emergence of novel applications such as catalysis, electronics, nanomaterial synthesis and biosensing. Additionally, polymer brushes prepared via SI-CRP have been utilized to modify the surface of novel substrates such as natural fibers, polymer nanofibers, mesoporous materials, graphene, viruses and protein nanoparticles. The last years have also seen exciting advances in the chemical and physical characterization of polymer brushes, as well as an ever increasing set of computational and simulation tools that allow understanding and predictions of these surface-grafted polymer architectures. The aim of this contribution is to provide a comprehensive review that critically assesses recent advances in the field and highlights the opportunities and challenges for future work.

Pick up, move and release of nanoparticles utilizing co-non-solvency of PNIPAM brushes

A critical complication in handling nanoparticles is the formation of large aggregates when particles are dried e.g. when they need to be transferred from one liquid to another. The particles in these aggregates need to disperse into the destined liquid medium, which has been proven difficult due to the relatively large interfacial interaction forces between nanoparticles. We present a simple method to capture, move and release nanoparticles without the formation of large aggregates. To do so, we employ the co-non-solvency effect of poly(N-isopropylacrylamide) (PNIPAM) brushes in water-ethanol mixtures. In pure water or ethanol, the densely end-anchored macromolecules in the PNIPAM brush stretch and absorb the solvent. We show that under these conditions, the adherence between the PNIPAM brush and a silicon oxide, gold, polystyrene or poly(methyl methacrylate) colloid attached to an atomic force microscopy cantilever is low. In contrast, when the PNIPAM brushes are in a collapsed state in a 30-70 vol% ethanol-water mixture, the adhesion between the brush and the different counter surfaces is high. For potential application, we demonstrate that this difference in adhesion can be utilized to pick up, move and release 900 silicon oxide nanoparticles of diameter 80 nm using only 10 × 10 μm² PNIPAM brush.

Self-Healing Superhydrophobic Fluoropolymer Brushes as Highly Protein-Repellent Coatings

Superhydrophobic surfaces with micro/nanostructures are widely used to prevent nonspecific adsorption of commercial polymeric and/or biological materials. Herein, a self-healing superhydrophobic and highly protein-repellent fluoropolymer brush was grafted onto nanostructured silicon by surface-initiated atom transfer radical polymerization (ATRP). Both the superhydrophobicity and antifouling properties (as indicated for isolated protein solutions and for 10% blood plasma) are well repaired upon serious chemical degradation (by e.g. air plasma). This brush still maintains excellent superhydrophobicity and good antifouling properties even after 5 damage-repair cycles, which opens a new door to fabricate long-term antifouling coatings on various substrates that can be used in harsh environments.