Control of neural stem cell adhesion and density by an electronic polymer surface switch

Electropolymerization processing of side-chain engineered EDOT for high performance microelectrode arrays

Microelectrode Arrays (MEAs) are popular tools for in vitro extracellular recording. They are often optimized by surface engineering to improve affinity with neurons and guarantee higher recording quality and stability. Recently, PEDOT:PSS has been used to coat microelectrodes due to its good biocompatibility and low impedance, which enhances neural coupling. Herein, we investigate on electro-co-polymerization of EDOT with its triglymated derivative to control valence between monomer units and hydrophilic functions on a conducting polymer. Molecular packing, cation complexation, dopant stoichiometry are governed by the glycolation degree of the electro-active coating of the microelectrodes. Optimal monomer ratio allows fine-tuning the material hydrophilicity and biocompatibility without compromising the electrochemical impedance of microelectrodes nor their stability while interfaced with a neural cell culture. After incubation, sensing readout on the modified electrodes shows higher performances with respect to unmodified electropolymerized PEDOT, with higher signal-to-noise ratio (SNR) and higher spike counts on the same neural culture. Reported SNR values are superior to that of state-of-the-art PEDOT microelectrodes and close to that of state-of-the-art 3D microelectrodes, with a reduced fabrication complexity. Thanks to this versatile technique and its impact on the surface chemistry of the microelectrode, we show that electro-co-polymerization trades with many-compound properties to easily gather them into single macromolecular structures. Applied on sensor arrays, it holds great potential for the customization of neurosensors to adapt to environmental boundaries and to optimize extracted sensing features.

Semiconducting electrodes for neural interfacing: a review

In the past 50 years, the advent of electronic technology to directly interface with neural tissue has transformed the fields of medicine and biology. Devices that restore or even replace impaired bodily functions, such as deep brain stimulators and cochlear implants, have ushered in a new treatment era for previously intractable conditions. Meanwhile, electrodes for recording and stimulating neural activity have allowed researchers to unravel the vast complexities of the human nervous system. Recent advances in semiconducting materials have allowed effective interfaces between electrodes and neuronal tissue through novel devices and structures. Often these are unattainable using conventional metallic electrodes. These have translated into advances in research and treatment. The development of semiconducting materials opens new avenues in neural interfacing. This review considers this emerging class of electrodes and how it can facilitate electrical, optical, and chemical sensing and modulation with high spatial and temporal precision. Semiconducting electrodes have advanced electrically based neural interfacing technologies owing to their unique electrochemical and photo-electrochemical attributes. Key operation modalities, namely sensing and stimulation in electrical, biochemical, and optical domains, are discussed, highlighting their contrast to metallic electrodes from the application and characterization perspective.

Molecularly cleavable bioinks facilitate high-performance digital light processing-based bioprinting of functional volumetric soft tissues

Digital light processing bioprinting favors biofabrication of tissues with improved structural complexity. However, soft-tissue fabrication with this method remains a challenge to balance the physical performances of the bioinks for high-fidelity bioprinting and suitable microenvironments for the encapsulated cells to thrive. Here, we propose a molecular cleavage approach, where hyaluronic acid methacrylate (HAMA) is mixed with gelatin methacryloyl to achieve high-performance bioprinting, followed by selectively enzymatic digestion of HAMA, resulting in tissue-matching mechanical properties without losing the structural complexity and fidelity. Our method allows cellular morphological and functional improvements across multiple bioprinted tissue types featuring a wide range of mechanical stiffness, from the muscles to the brain, the softest organ of the human body. This platform endows us to biofabricate mechanically precisely tunable constructs to meet the biological function requirements of target tissues, potentially paving the way for broad applications in tissue and tissue model engineering.

Organic Bioelectronics for In Vitro Systems

Bioelectronics have made strides in improving clinical diagnostics and precision medicine. The potential of bioelectronics for bidirectional interfacing with biology through continuous, label-free monitoring on one side and precise control of biological activity on the other has extended their application scope to in vitro systems. The advent of microfluidics and the considerable advances in reliability and complexity of in vitro models promise to eventually significantly reduce or replace animal studies, currently the gold standard in drug discovery and toxicology testing. Bioelectronics are anticipated to play a major role in this transition offering a much needed technology to push forward the drug discovery paradigm. Organic electronic materials, notably conjugated polymers, having demonstrated technological maturity in fields such as solar cells and light emitting diodes given their outstanding characteristics and versatility in processing, are the obvious route forward for bioelectronics due to their biomimetic nature, among other merits. This review highlights the advances in conjugated polymers for interfacing with biological tissue in vitro, aiming ultimately to develop next generation in vitro systems. We showcase in vitro interfacing across multiple length scales, involving biological models of varying complexity, from cell components to complex 3D cell cultures. The state of the art, the possibilities, and the challenges of conjugated polymers toward clinical translation of in vitro systems are also discussed throughout.

Terminal cationization of poly(N-isopropylacrylamide) brush surfaces facilitates efficient thermoresponsive control of cell adhesion and detachment

A variety of poly(N-isopropylacrylamide) (PIPAAm)-grafted surfaces have been reported for temperature-controlled cell adhesion/detachment. However, the surfaces reported to date need further improvement to achieve good outcomes for both cell adhesion and detachment, which are inherently contradictory behaviors. This study investigated the effects of terminal cationization and length of grafted PIPAAm chains on temperature-dependent cell behavior. PIPAAm brushes with three chain lengths were constructed on glass coverslips via surface-initiated reversible addition-fragmentation chain transfer (RAFT) polymerization. Terminal substitution of the grafted PIPAAm chains with either monocationic trimethylammonium or nonionic isopropyl moieties was performed through the reduction of terminal RAFT-related groups and subsequent thiol-ene reaction with the corresponding acrylamide derivatives. Although the thermoresponsive properties of the PIPAAm brush surfaces were scarcely affected by the terminal functional moiety, the zeta potentials of the cationized PIPAAm surfaces were higher than those of the nonionized ones, both below and above the phase transition temperature of PIPAAm (30°C). When bovine endothelial cells were cultured on each surface at 37°C, the number of adherent cells decreased with longer PIPAAm. Notably, cell adhesion on the cationized PIPAAm surfaces was higher than that on the nonionized surfaces. This terminal effect on cell adhesion gradually weakened with increasing PIPAAm length. In particular, long-chain PIPAAm brushes virtually showed cell repellency even at 37°C, regardless of the termini. Interestingly, moderately long-chain PIPAAm brushes promoted cell detachment at 20°C, with negligible terminal electrostatic interruption. Consequently, both cell adhesion and detachment were successfully improved by choosing an appropriate PIPAAm length with terminal cationization.

Stimuli-Responsive Biomaterials: Scaffolds for Stem Cell Control

Stem cell fate is closely intertwined with microenvironmental and endogenous cues within the body. Recapitulating this dynamic environment ex vivo can be achieved through engineered biomaterials which can respond to exogenous stimulation (including light, electrical stimulation, ultrasound, and magnetic fields) to deliver temporal and spatial cues to stem cells. These stimuli-responsive biomaterials can be integrated into scaffolds to investigate stem cell response in vitro and in vivo, and offer many pathways of cellular manipulation: biochemical cues, scaffold property changes, drug release, mechanical stress, and electrical signaling. The aim of this review is to assess and discuss the current state of exogenous stimuli-responsive biomaterials, and their application in multipotent stem cell control. Future perspectives in utilizing these biomaterials for personalized tissue engineering and directing organoid models are also discussed.

Micropatterned Smart Culture Surfaces via Multi-Step Physical Coating of Functional Block Copolymers for Harvesting Cell Sheets with Controlled Sizes and Shapes

Cell micropatterning on micropatterned thermoresponsive polymer-based culture surfaces facilitates the creation of on-demand and functional cell sheets. However, the fabrication of micropatterned surfaces generally includes complicated procedures with multi-step chemical reactions. To overcome this issue, this study proposes a facile preparation of micropatterned thermoresponsive surfaces via a two-step physical coating of two different diblock copolymers. Both copolymers contain poly(butyl methacrylate) blocks as hydrophobic anchors for water-stable polymer deposition. At first, thermoresponsive polymer layers are constructed on cell culture dishes via spin-coating block copolymers containing poly(N-isopropylacrylamide) blocks that exhibit a transition temperature of ≈30 °C in aqueous media. To create polymer micropatterns on the thermoresponsive surfaces, microcontact printing of block copolymers containing hydrophilic poly(N-acryloylmorpholine) (PNAM) blocks is performed using polydimethylsiloxane stamps. Stamped PNAM-based block polymers are adsorbed to the outermost thermoresponsive surfaces, and increase the surface hydrophilicity with decreasing protein adsorption. Cells adhere and proliferate on the thermoresponsive domains at 37 °C, whereas the stamped hydrophilic domains remain cell-repellent for 7 days. At 20 °C, cell sheets with controlled sizes and shapes are harvested from the surfaces with the desired micropatterns. This technique is useful for the preparation of micropatterned polymer surfaces for various biomedical applications.

Water stable nanocoatings of poly(N-isopropylacrylamide)-based block copolymers on culture insert membranes for temperature-controlled cell adhesion

This study demonstrated the spin-coating of functional diblock copolymers to develop smart culture inserts for thermoresponsive cell adhesion/detachment control. One part of the block components, the poly(n-butyl methacrylate) block, strongly supported the water stable surface-immobilization of the thermoresponsive poly(N-isopropylacrylamide) (PNIPAAm) block, regardless of temperature. The chain length of the PNIPAAm blocks was varied to regulate thermal surface functions. Immobilized PNIPAAm concentrations became larger with increasing chain length (1.0-1.6 μg cm^-2) and the thicknesses of individual layers were relatively comparable at 10-odd nanometers. A nanothin coating scarcely inhibited the permeability of the original porous membrane. When human fibroblasts were cultured on each surface at 37 °C, the efficiencies of cell adhesion and proliferation decreased with longer PNIPAAm chains. Meanwhile, by reducing the temperature to 20 °C, longer PNIPAAm chains promoted cell detachment owing to the significant thermoresponsive alteration of cell-surface affinity. Consequently, we successfully produced a favorable cell sheet by choosing an appropriate PNIPAAm length for block copolymers.

Growth and Spatial Control of Murine Neural Stem Cells on Reflectin Films

Stem cells have attracted significant attention due to their regenerative capabilities and their potential for the treatment of disease. Consequently, significant research effort has focused on the development of protein- and polypeptide-based materials as stem cell substrates and scaffolds. Here, we explore the ability of reflectin, a cephalopod structural protein, to support the growth of murine neural stem/progenitor cells (mNSPCs). We observe that the binding, growth, and differentiation of mNSPCs on reflectin films is comparable to that on more established protein-based materials. Moreover, we find that heparin selectively inhibits the adhesion of mNSPCs on reflectin, affording spatial control of cell growth and leading to a >30-fold change in cell density on patterned substrates. The described findings highlight the potential utility of reflectin as a stem cell culture material.

Conjugated Polymers for Assessing and Controlling Biological Functions

The field of organic bioelectronics is advancing rapidly in the development of materials and devices to precisely monitor and control biological signals. Electronics and biology can interact on multiple levels: organs, complex tissues, cells, cell membranes, proteins, and even small molecules. Compared to traditional electronic materials such as metals and inorganic semiconductors, conjugated polymers (CPs) have several key advantages for biological interactions: tunable physiochemical properties, adjustable form factors, and mixed conductivity (ionic and electronic). Herein, the use of CPs in five biologically oriented research topics, electrophysiology, tissue engineering, drug release, biosensing, and molecular bioelectronics, is discussed. In electrophysiology, implantable devices with CP coating or CP-only electrodes are showing improvements in signal performance and tissue interfaces. CP-based scaffolds supply highly favorable static or even dynamic interfaces for tissue engineering. CPs also enable delivery of drugs through a variety of mechanisms and form factors. For biosensing, CPs offer new possibilities to incorporate biological sensing elements in a conducting matrix. Molecular bioelectronics is today used to incorporate (opto)electronic functions in living tissue. Under each topic, the limits of the utility of CPs are discussed and, overall, the major challenges toward implementation of CPs and their devices to real-world applications are highlighted.

Capillary-Fiber Based Electrophoretic Delivery Device

Organic electronic ion pumps (OEIPs) are versatile tools for electrophoretic delivery of substances with high spatiotemporal resolution. To date, OEIPs and similar iontronic components have been fabricated using thin-film techniques and often rely on laborious, multistep photolithographic processes. OEIPs have been demonstrated in a variety of in vitro and in vivo settings for controlling biological systems, but the thin-film form factor and limited repertoire of polyelectrolyte materials and device fabrication techniques unnecessarily constrain the possibilities for miniaturization and extremely localized substance delivery, e.g., the greater range of pharmaceutical compounds, on the scale of a single cell. Here, we demonstrate an entirely new OEIP form factor based on capillary fibers that include hyperbranched polyglycerols (dPGs) as the selective electrophoretic membrane. The dPGs enable electrophoretic channels with a high concentration of fixed charges and well-controlled cross-linking and can be realized using a simple "one-pot" fluidic manufacturing protocol. Selective electrophoretic transport of cations and anions of various sizes is demonstrated, including "large" substances that are difficult to transport with other OEIP technologies. We present a method for tailoring and characterizing the electrophoretic channels' fixed charge concentration in the operational state. Subsequently, we compare the experimental performance of these capillary OEIPs to a computational model and explain unexpected features in the ionic current for the transport and delivery of larger, lower-mobility ionic compounds. From this model, we are able to elucidate several operational and design principles relevant to miniaturized electrophoretic drug delivery technologies in general. Overall, the compactness of the capillary OEIP enables electrophoretic delivery devices with probelike geometries, suitable for a variety of ionic compounds, paving the way for less-invasive implantation into biological systems and for healthcare applications.

Effect of monophasic pulsed stimulation on live single cell de-adhesion on conducting polymers with adsorbed fibronectin as revealed by single cell force spectroscopy

The force required to detach a single fibroblast cell in contact with the conducting polymer, polypyrrole doped with dodecylbenzene, was quantified using the Atomic Force Microscope-based technique, Single Cell Force Spectroscopy. The de-adhesion force for a single cell was 0.64 ± 0.03 nN and predominately due to unbinding of α5β1 integrin complexes with surface adsorbed fibronectin, as confirmed by blocking experiments using antibodies. Monophasic pulsed stimulation (50 μs pulse duration) superimposed on either an applied oxidation (+500) or reduction (-500 mV) constant voltage caused a significant decrease in the de-adhesion force by 30%-45% to values ranging from 0.34 to 0.43 nN (±0.02 nN). The electrical stimulation caused a reduction in the molecular-level jump and plateau interactions, while an opposing increase in nonspecific interactions was observed during the cell de-adhesion process. Due to the monophasic pulsed stimulation, there is an apparent change or weakening of the cell membrane properties, which is suggested to play a role in reducing the cell de-adhesion. Based on this study, pulsed stimulation with optimized threshold parameters represents a possible approach to tune cell interactions and adhesion on conducting polymers.

Cyclic Redox-Mediated Switching of Surface Properties of Thiolated Polysaccharide Multilayers and Its Effect on Fibroblast Adhesion

Advanced technologies for controlled cell adhesion and detachment in novel biointerface designs profit from stimuli-responsive systems that are able to react to their environment. Here, a multilayer system made of thiolated chitosan and thiolated chondroitin sulfate was constructed, with the potential of switchable inter- and intramolecular thiol/disulfide interactions representing a redox-sensitive nanoplatform. Owing to the formation and cleavage of inherent disulfide bonds by oxidation and reduction, surface properties of the multilayer can be controlled toward protein adsorption/desorption and cell adhesion in a reversible manner. Oxidation of thiols by chloramine-T promotes fibronectin (FN) adsorption and fibroblast cell adhesion, whereas the reduction by tris(2-carboxyethyl)phosphine reverses these effects, leading to low FN adsorption and little cell adhesion and spreading. These effects on the biological systems are related to significant changes of wetting properties, zeta potential, and mechanical properties of these multilayer films. The system presented may be useful for biomedical applications as responsive and obedient surfaces in medical implants and support tissue regeneration.

Switchable presentation of cytokines on electroactive polypyrrole surfaces for hematopoietic stem and progenitor cells

Hematopoietic stem cells are used in transplantations for patients with hematologic malignancies. Scarce sources require efficient strategies of expansion, including polymeric biomaterials mimicking architectures of bone marrow tissue. Tissue microenvironment and mode of cytokine presentation strongly influence cell fate. Although several cytokines with different functions as soluble or membrane-bound mediators have already been identified, their precise roles have not yet been clarified. A need exists for in vitro systems that mimic the in vivo situation to enable such studies. One way is to establish surfaces mimicking physiological presentation using protein-immobilization onto polymer films. However these films merely provide a static presentation of the immobilized proteins. It would be advantageous to also dynamically change protein presentation and functionality to better reflect the in vivo conditions. The electroactive polymer polypyrrole shows excellent biocompatibility and electrochemically alters its surface properties, becoming an interesting choice for such setups. Here, we present an in vitro system for switchable presentation of membrane-bound cytokines. We use interleukin IL-3, known to affect hematopoiesis, and show that when immobilized on polypyrrole films, IL-3 is bioavailable for the bone marrow-derived FDC-P1 progenitor cell line. Moreover, IL-3 presentation can be successfully altered by changing the redox state of the film, in turn influencing FDC-P1 cell viability. This novel in vitro system provides a valuable tool for stimuli-responsive switchable protein presentation allowing the dissection of relevant mediators in stem and progenitor cell behavior.

Novel Conducting and Biodegradable Copolymers with Noncytotoxic Properties toward Embryonic Stem Cells

Electroactive biomaterials that are easily processed as scaffolds with good biocompatibility for tissue regeneration are difficult to design. Herein, the synthesis and characterization of a variety of novel electroactive, biodegradable biomaterials based on poly(3,4-ethylenedioxythiphene) copolymerized with poly(d,l lactic acid) (PEDOT-co-PDLLA) are presented. These copolymers were obtained using (2,3-dihydrothieno[3,4-b][1,4]dioxin-2-yl)methanol (EDOT-OH) as an initiator in a lactide ring-opening polymerization reaction, resulting in EDOT-PDLLA macromonomer. Conducting PEDOT-co-PDLLA copolymers (in three different proportions) were achieved by chemical copolymerization with 3,4-ethylenedioxythiophene (EDOT) monomers and persulfate oxidant. The PEDOT-co-PDLLA copolymers were structurally characterized by 1H NMR and Fourier transform infrared spectroscopy. Cyclic voltammetry confirmed the electroactive character of the materials, and conductivity measurements were performed via electrochemical impedance spectroscopy. In vitro biodegradability was evaluated using proteinase K over 35 days, showing 29-46% (w/w) biodegradation. Noncytotoxicity was assessed by adhesion, migration, and proliferation assays using embryonic stem cells (E14.tg2a); excellent neuronal differentiation was observed. These novel electroactive and biodegradable PEDOT-co-PDLLA copolymers present surface chemistry and charge density properties that make them potentially useful as scaffold materials in different fields of applications, especially for neuronal tissue engineering.

Topographical and Electrical Stimulation of Neuronal Cells through Microwrinkled Conducting Polymer Biointerfaces

The development of smart biointerfaces combining multiple functions is crucial for triggering a variety of cellular responses. In this work, wrinkled organic interfaces based on the conducting polymer poly(3,4-ethylene dioxythiophene) doped with poly(styrene sulfonate) are developed with the aim to simultaneously convey electrical and topographical stimuli to cultured cells. The surface wrinkling of thin films on heat-shrink polymer sheets allows for rapid patterning of self-assembled anisotropic topographies characterized by micro/sub-microscale aligned wrinkles. The developed interfaces prove to support the growth and differentiation of neural cells (SH-SY5Y, human neuroblastoma) and are remarkably effective in promoting axonal guidance, by guiding and stimulating the neurite growth in differentiating cells. Electrical stimulation with biphasic pulses delivered through the conductive wrinkled interface is found to further promote the neurite growth, demonstrating the suitability of such interfaces as platforms for conveying multiple stimuli to cells and tissues.

Electrically Controlled "Sponge Effect" of PEDOT:PSS Governs Membrane Potential and Cellular Growth

PSS is a highly conductive material with good thermal and chemical stability and enhanced biocompatibility that make it suitable for bioengineering applications. The electrical control of the oxidation state of PEDOT:PSS films allows modulation of peculiar physical and chemical properties of the material, such as topography, wettability, and conductivity, and thus offers a possible route for controlling cellular behavior. Through the use of (i) the electrophysiological response of the plasma membrane as a biosensor of the ionic availability; (ii) relative abundance around the cells via X-ray spectroscopy; and (iii) atomic force microscopy to monitor PEDOT:PSS film thickness relative to its oxidation state, we demonstrate that redox processes confer to PEDOT:PSS the property to modify the ionic environment at the film-liquid interface through a "sponge-like" effect on ions. Finally, we show how this property offers the capability to electrically control central cellular properties such as viability, substrate adhesion, and growth, paving the way for novel bioelectronics and biotechnological applications.

Dynamically Tunable Cell Culture Platforms for Tissue Engineering and Mechanobiology

Human tissues are sophisticated ensembles of many distinct cell types embedded in the complex, but well-defined, structures of the extracellular matrix (ECM). Dynamic biochemical, physicochemical, and mechano-structural changes in the ECM define and regulate tissue-specific cell behaviors. To recapitulate this complex environment in vitro, dynamic polymer-based biomaterials have emerged as powerful tools to probe and direct active changes in cell function. The rapid evolution of polymerization chemistries, structural modulation, and processing technologies, as well as the incorporation of stimuli-responsiveness, now permit synthetic microenvironments to capture much of the dynamic complexity of native tissue. These platforms are comprised not only of natural polymers chemically and molecularly similar to ECM, but those fully synthetic in origin. Here, we review recent in vitro efforts to mimic the dynamic microenvironment comprising native tissue ECM from the viewpoint of material design. We also discuss how these dynamic polymer-based biomaterials are being used in fundamental cell mechanobiology studies, as well as towards efforts in tissue engineering and regenerative medicine.

Film Thickness Determines Cell Growth and Cell Sheet Detachment from Spin-Coated Poly(N-Isopropylacrylamide) Substrates

Poly(N-isopropylacrylamide) (pNIPAm) is widely used to fabricate thermoresponsive surfaces for cell sheet detachment. Many complex and expensive techniques have been employed to produce pNIPAm substrates for cell culture. The spin-coating technique allows rapid fabrication of pNIPAm substrates with high reproducibility and uniformity. In this study, the dynamics of cell attachment, proliferation, and function on non-cross-linked spin-coated pNIPAm films of different thicknesses were investigated. The measurements of advancing contact angle revealed increasing contact angles with increasing film thickness. Results suggest that more hydrophilic 50 and 80 nm thin pNIPAm films are more preferable for cell sheet fabrication, whereas more hydrophobic 300 and 900 nm thick spin-coated pNIPAm films impede cell attachment. These changes in cell behavior were correlated with changes in thickness and hydration of pNIPAm films. The control of pNIPAm film thickness using the spin-coating technique offers an effective tool for cell sheet-based tissue engineering.

Organic Bioelectronics: Bridging the Signaling Gap between Biology and Technology

The electronics surrounding us in our daily lives rely almost exclusively on electrons as the dominant charge carrier. In stark contrast, biological systems rarely use electrons but rather use ions and molecules of varying size. Due to the unique combination of both electronic and ionic/molecular conductivity in conducting and semiconducting organic polymers and small molecules, these materials have emerged in recent decades as excellent tools for translating signals between these two realms and, therefore, providing a means to effectively interface biology with conventional electronics-thus, the field of organic bioelectronics. Today, organic bioelectronics defines a generic platform with unprecedented biological recording and regulation tools and is maturing toward applications ranging from life sciences to the clinic. In this Review, we introduce the field, from its early breakthroughs to its current results and future challenges.

Electroconductive Nanopatterned Substrates for Enhanced Myogenic Differentiation and Maturation

Electrically conductive materials provide a suitable platform for the in vitro study of excitable cells, such as skeletal muscle cells, due to their inherent conductivity and electroactivity. Here it is demonstrated that bioinspired electroconductive nanopatterned substrates enhance myogenic differentiation and maturation. The topographical cues from the highly aligned collagen bundles that form the extracellular matrix of skeletal muscle tissue are mimicked using nanopatterns created with capillary force lithography. Electron beam deposition is then utilized to conformally coat nanopatterned substrates with a thin layer of either gold or titanium to create electroconductive substrates with well-defined, large-area nanotopographical features. C2C12 cells, a myoblast cell line, are cultured for 7 d on substrates and the effects of topography and electrical conductivity on cellular morphology and myogenic differentiation are assessed. It is found that biomimetic nanotopography enhances the formation of aligned myotubes and the addition of an electroconductive coating promotes myogenic differentiation and maturation, as indicated by the upregulation of myogenic regulatory factors Myf5, MyoD, and myogenin (MyoG). These results suggest the suitability of electroconductive nanopatterned substrates as a biomimetic platform for the in vitro engineering of skeletal muscle tissue.

Biofunctionalization of polydioxythiophene derivatives for biomedical applications

It is becoming clear that development of biomedical devices relies on engineering of the interface between the device and the biological component. Improved performance for these sensors and devices can be achieved through biofunctionalization. In this review we focus on highlighting the biofunctionalization of polydioxythiophene sensors.

Quantifying Molecular-Level Cell Adhesion on Electroactive Conducting Polymers using Electrochemical-Single Cell Force Spectroscopy

Single Cell Force Spectroscopy was combined with Electrochemical-AFM to quantify the adhesion between live single cells and conducting polymers whilst simultaneously applying a voltage to electrically switch the polymer from oxidized to reduced states. The cell-conducting polymer adhesion represents the non-specific interaction between cell surface glycocalyx molecules and polymer groups such as sulfonate and dodecylbenzene groups, which rearrange their orientation during electrical switching. Single cell adhesion significantly increases as the polymer is switched from an oxidized to fully reduced state, indicating stronger cell binding to sulfonate groups as opposed to hydrophobic groups. This increase in single cell adhesion is concomitant with an increase in surface hydrophilicity and uptake of cell media, driven by cation movement, into the polymer film during electrochemical reduction. Binding forces between the glycocalyx and polymer surface are indicative of molecular-level interactions and during electrical stimulation there is a decrease in both the binding force and stiffness of the adhesive bonds. The study provides insight into the effects of electrochemical switching on cell adhesion at the cell-conducting polymer interface and is more broadly applicable to elucidating the binding of cell adhesion molecules in the presence of electrical fields and directly at electrode interfaces.

Physical and Electrochemical Properties of PEDOT:PSS as a Tool for Controlling Cell Growth

Conducting polymers are promising materials for tissue engineering applications, since they can both provide a biocompatible scaffold for physical support of living cells, and transmit electrical and mechanical stimuli thanks to their electrical conductivity and reversible doping. In this work, thin films of one of the most promising materials for bioelectronics applications, poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) (

PEDOT

PSS), are prepared using two different techniques, spin coating and electrochemical polymerization, and their oxidation state is subsequently changed electrochemically with the application of an external bias. The electrochemical properties of these different types of

PEDOT

PSS are studied through cyclic voltammetry and spectrophotometry to assess the effectiveness of the oxidation process and its stability over time. Their surface physical properties and their dependence on the redox state of

PEDOT

PSS are investigated using atomic force microscopy (AFM), water contact angle goniometry and sheet resistance measurements. Finally, human glioblastoma multiforme cells (T98G) and primary human dermal fibroblasts (hDF) are cultured on

PEDOT

PSS films with different oxidation states, finding that the effect of the substrate on the cell growth rate is strongly cell-dependent: T98G growth is enhanced by the reduced samples, while hDF growth is more effective only on the oxidized substrates that show a strong chemical interaction with the cell culture medium.

Directed Neural Stem Cell Differentiation with a Functionalized Graphene Oxide Nanocomposite

Neural stem cell (NSC) transplantation has the potential to restore function to diseased or damaged nervous tissue, but poor control over cell survival, differentiation, and maturation limits therapeutic prospects. Engineered scaffolds that have the ability to drive neural stem cell behavior can address these limitations facing cell transplantation. Conducting polymers, which have the ability to electrically interface with cells, are attractive scaffolding candidates, but they lack the capacity for simple covalent modification, which would enable surface patterning of biomolecules. In this work, the NSC scaffolding performance of a nanocomposite composed of conducting polymer poly(3,4-ethylenedioxythiophene) (PEDOT) and graphene oxide (GO) nanosheets (GO/PEDOT) is investigated. The GO/PEDOT material is nontoxic and improves NSC differentiation toward the neuronal lineage. Biomolecules interferon-γ (IFNγ) and platelet-derived growth factor (PDGF) that selectively promote neuronal or oligodendrocyte lineage differentiation, respectively, are covalently cross-linked to the surface of the GO/PEDOT nanocomposite via carboxylic acid functional groups provided by GO using carbodiimide chemistry. The surfaces support a larger population of neurons when modified with IFNγ and a larger population of oligodendrocytes when modified by PDGF. This work demonstrates the customizability of GO/PEDOT for cell scaffolding applications and underlines its potential for controlling NSC behavior to improve therapeutic potential.

A lysinated thiophene-based semiconductor as a multifunctional neural bioorganic interface

Lysinated molecular organic semiconductors are introduced as valuable multifunctional platforms for neural cells growth and interfacing. Cast films of quaterthiophene (T4) semiconductor covalently modified with lysine-end moieties (T4Lys) are fabricated and their stability, morphology, optical/electrical, and biocompatibility properties are characterized. T4Lys films exhibit fluorescence and electronic transport as generally observed for unsubstituted oligothiophenes combined to humidity-activated ionic conduction promoted by the charged lysine-end moieties. The Lys insertion in T4 enables adhesion of primary culture of rat dorsal root ganglion (DRG), which is not achievable by plating cells on T4. Notably, on T4Lys, the number on adhering neurons/area is higher and displays a twofold longer neurite length than neurons plated on glass coated with poly-l-lysine. Finally, by whole-cell patch-clamp, it is shown that the biofunctionality of neurons cultured on T4Lys is preserved. The present study introduces an innovative concept for organic material neural interface that combines optical and iono-electronic functionalities with improved biocompatibility and neuron affinity promoted by Lys linkage and the softness of organic semiconductors. Lysinated organic semiconductors could set the scene for the fabrication of simplified bioorganic devices geometry for cells bidirectional communication or optoelectronic control of neural cells biofunctionality.

3D Conducting Polymer Platforms for Electrical Control of Protein Conformation and Cellular Functions

We report the fabrication of three dimensional (3D) macroporous scaffolds made from poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) via an ice-templating method. The scaffolds offer tunable pore size and morphology, and are electrochemically active. When a potential is applied to the scaffolds, reversible changes take place in their electrical doping state, which in turn enables precise control over the conformation of adsorbed proteins (e.g., fibronectin). Additionally, the scaffolds support the growth of mouse fibroblasts (3T3-L1) for 7 days, and are able to electrically control cell adhesion and pro-angiogenic capability. These 3D matrix-mimicking platforms offer precise control of protein conformation and major cell functions, over large volumes and long cell culture times. As such, they represent a new tool for biological research with many potential applications in bioelectronics, tissue engineering, and regenerative medicine.

Poly[3,4-ethylene dioxythiophene (EDOT) -co- 1,3,5-tri[2-(3,4-ethylene dioxythienyl)]-benzene (EPh)] copolymers (PEDOT-co-EPh): optical, electrochemical and mechanical properties

PEDOT-co-EPh copolymers with systematic variations in composition were prepared by electrochemical polymerization from mixed monomer solutions in acetonitrile. The EPh monomer is a trifunctional crosslinking agent with three EDOTs around a central benzene ring. With increasing EPh content, the color of the copolymers changed from blue to yellow to red due to decreased absorption in the near infrared (IR) spectrum and increased absorption in the visible spectrum. The surface morphology changed from rough and nanofibrillar to more smooth with rounded bumps. The electrical transport properties dramatically decreased with increasing EPh content, resulting in coatings that either substantially lowered the impedance of the electrode (at the lowest EPh content), leave the impedance nearly unchanged (near 1% EPh), or significantly increase the impedance (at 1% and above). The mechanical properties of the films were substantially improved with EPh content, with the 0.5% EPh films showing an estimated 5x improvement in modulus measured by AFM nanoindentation. The PEDOT-co-EPh copolymer films were all shown to be non-cytotoxic toward and promote the neurite outgrowth of PC12 cells. Given these results, we expect that the films of most interest for neural interface applications will be those with improved mechanical properties that maintain the improved charge transport performance (with 1% EPh and below).

Electronic control of platelet adhesion using conducting polymer microarrays

We hereby report a method to fabricate addressable micropatterns of e-surfaces based on the conducting polymer poly(3,4-ethylenedioxythiophene) doped with the anion tosylate (PEDOT:Tos) to gain dynamic control over the spatial distribution of platelets in vitro. With thin film processing and microfabrication techniques, patterns down to 10 μm were produced to enable active regulation of platelet adhesion at high spatial resolution. Upon electronic addressing, both reduced and oxidized surfaces were created within the same device. This surface modulation dictates the conformation and/or orientation, rather than the concentration, of surface proteins, thus indirectly regulating the adhesion of platelets. The reduced electrode supported platelet adhesion, whereas the oxidized counterpart inhibited adhesion. PEDOT:Tos electrode fabrication is compatible with most of the classical patterning techniques used in printing as well as in the electronics industry. The first types of tools promise ultra-low-cost production of low-resolution (>30 μm) electrode patterns that may combine with traditional substrates and dishes used in a classical analysis setup. Platelets play a pronounced role in cardiovascular diseases and have become an important drug target in order to prevent thrombosis. This clinical path has in turn generated a need for platelet function tests to monitor and assess platelet drug efficacy. The spatial control of platelet adherence presented here could prove valuable for blood cell separation or biosensor microarrays, e.g. in diagnostic applications where platelet function is evaluated.

A review of organic and inorganic biomaterials for neural interfaces

Recent advances in nanotechnology have generated wide interest in applying nanomaterials for neural prostheses. An ideal neural interface should create seamless integration into the nervous system and performs reliably for long periods of time. As a result, many nanoscale materials not originally developed for neural interfaces become attractive candidates to detect neural signals and stimulate neurons. In this comprehensive review, an overview of state-of-the-art microelectrode technologies provided fi rst, with focus on the material properties of these microdevices. The advancements in electro active nanomaterials are then reviewed, including conducting polymers, carbon nanotubes, graphene, silicon nanowires, and hybrid organic-inorganic nanomaterials, for neural recording, stimulation, and growth. Finally, technical and scientific challenges are discussed regarding biocompatibility, mechanical mismatch, and electrical properties faced by these nanomaterials for the development of long-lasting functional neural interfaces.

Influence of conductive polymer doping on the viability of cardiac progenitor cells

Investigating the influence of conductive polymer dopants on surface properties and chemistry, and how they may modify cardiac progenitor cell interactions.

Organic electrochemical transistor array for recording transepithelial ion transport of human airway epithelial cells

An organic electrochemical transistor array is integrated with human airway epithelial cells. This integration provides a novel method to couple transepithelial ion transport with electrical current. Activation and inhibition of transepithelial ion transport are readily detected with excellent time resolution. The organic electrochemical transistor array serves as a promising platform for physiological studies and drug testing.

Patterned free-standing conductive nanofilms for ultraconformable circuits and smart interfaces

A process is presented for the fabrication of patterned ultrathin free-standing conductive nanofilms based on an all-polymer bilayer structure composed of poly(3,4-ethylenedioxythiophene)/poly(styrene sulfonate) and poly(lactic acid) (PEDOT:PSS/PLA). Based on the strategy recently introduced by our group for producing large area free-standing nanofilms of conductive polymers with ultrahigh conformability, here an inkjet subtractive patterning technique was used, with localized overoxidation of PEDOT:PSS that caused the local irreversible loss of electrical conductivity. Different pattern geometries (e.g., interdigitated electrodes with various spacing, etc.) were tested for validating the proposed process. The fabrication of individually addressable microelectrodes and simple circuits on nanofilm having thickness ∼250 nm has been demonstrated. Using this strategy, mechanically robust, conformable ultrathin polymer films could be produced that can be released in water as free-standing nanofilms and/or collected on surfaces with arbitrary shapes, topography and compliance, including human skin. The patterned bilayer nanofilms were characterized as regards their morphology, thickness, topography, conductivity, and electrochemical behavior. In addition, the electrochemical switching of surface properties has been evaluated by means of contact angle measurements. These novel conductive materials can find use as ultrathin, conformable electronic devices and in many bioelectrical applications. Moreover, by exploiting the electrochemical properties of conducting polymers, they can act as responsive smart biointerfaces and in the field of conformable bioelectronics, for example, as electrodes on tissues or smart conductive substrates for cell culturing and stimulation.

Noninvasive photodetachment of stem cells on tunable conductive polymer nano thin films: selective harvesting and preserved differentiation capacity

Viable mesenchymal stem cells (MSCs) were efficiently and selectively harvested by near-infrared (NIR) light using the photothermal effect of a conductive polymer nano thin film. The poly(3,4-ethylenedioxy thiophene) (PEDOT)-coated cell culture surfaces were prepared via a simple and fast solution-casting polymerization (SCP) technique. The absorption of PEDOT thin films in the NIR region was effectively triggered cell harvesting upon exposure to an NIR source. By controlling the NIR absorption of the PEDOT film through electrochemical doping or growing PEDOT with different thin film thickness from 70 to 300 nm, the proliferation and harvesting of MSCs on the PEDOT surface were controlled quantitatively. This light-induced cell detachment method based on PEDOT films provides the temporal and spatial control of cell harvesting, as well as cell patterning. The harvested stem cells were found to be alive and well proliferated despite the use of temperature increase by NIR. More importantly, the harvested MSCs by this method preserved their intrinsic characteristics as well as multilineage differentiation capacities. This PEDOT surfaces could be used for repetitive culture and detachment of MSCs or for efficient selection or depletion of a specific subset from heterogeneous population during culture of various tissue-derived cells because there were no photodegradation and photobreakage in the PEDOT films by NIR exposure.

Quantifying fibronectin adhesion with nanoscale spatial resolution on glycosaminoglycan doped polypyrrole using Atomic Force Microscopy

BACKGROUND

The interaction of ECM proteins is critical in determining the performance of materials used in biomedical applications such as tissue regeneration, implantable bionics and biosensing.

METHODS

To improve our understanding of ECM protein-conducting polymer interactions, we have used Atomic Force Microscopy (AFM) to elucidate the interactions of fibronectin (FN) on polypyrrole (PPy) doped with different glycosaminoglycans.

RESULTS

We were able to classify four main types of FN interactions, including those related to 1) non-specific adhesion, 2) protein unfolding and subsequent unbinding from the surface, 3) desorption and 4) interactions with no adhesion. FN adhesion on PPy/hyaluronic acid showed a significantly lower density of surface adhesion with the adhesion restricted to nodule structures, as opposed to their peripheries, of the polymer morphology. In contrast, PPy/chondroitin sulfate showed a significantly higher density of surface adhesion to the point where the distribution of adhesion effectively masked the topography. Through conductive AFM imaging, we found that the conductive regions correlated with regions of FN adhesion.

CONCLUSIONS

Given that the conductivity requires doping of the polymer, these findings suggest that FN adhesion is mediated by interactions with chondroitin sulfate and hyaluronic acid at the polymer surface and may be indicative of specific interactions due to contributions from electrostatic attraction between the FN and sulfate/anionic groups of the dopants.

GENERAL SIGNIFICANCE

This study demonstrates the ability of AFM to resolve the protein-conducting polymer interactions at the molecular and nanoscale level, which will be important for interfacing these polymer materials with biological systems. This article is part of a Special Issue entitled Organic Bioelectronics - Novel Applications in Biomedicine.

Microwrinkled conducting polymer interface for anisotropic multicellular alignment

Surfaces with controlled micro and nanoscale topographical cues are useful as smart scaffolds and biointerfaces for cell culture. Recently, use of thin-film and surface wrinkling is emerging as a rapid unconventional method for preparing topographically patterned surfaces, especially suited for the production of smart patterns over large area surfaces. On the other hand, there is an increasing interest in employing conducting polymers as soft, biocompatible, conductive biointerfaces or as parts of bioelectronic devices. A novel convenient and versatile method is presented for producing anisotropic topographical cues at the micro- and nanoscale on conducting polymer surfaces. Micro and nanowrinkles were formed during the heat-shrinking process of a thermo-retractable polystyrene substrate. Surface wrinkling was due to the mismatch between the mechanical properties of a conducting polymer ultrathin film and the substrate. Various geometries of wrinkled structures were prepared, demonstrating the tunability of topography depending on the thickness of the conductive film. A method for patterning the conductive properties of the wrinkled substrates was also presented. Such surfaces acted as smart scaffolds for the functional alignment of cells, envisioning their electrical stimulation. Cell adhesion and proliferation were evaluated, comparing different topographies, and a preferential anisotropic alignment of C2C12 murine skeletal muscle cells along wrinkles was demonstrated. The observed trends were also confirmed concerning the formation of aligned myotubes in C2C12 differentiation stage. Furthermore, improved results in terms of aligned and mature myotube formation were obtained by co-culturing C2C12 cells with a fibroblasts feeder layer. The combination of living cells and tunable conductive nanowrinkles will represent a unique tool for the development of innovative biomedical devices.

Electrically tunable organic bioelectronics for spatial and temporal manipulation of neuron-like pheochromocytoma (PC-12) cells

BACKGROUND

Organic bioelectronic devices consisting of alternating poly(3,4-ethylenedioxythiophene) (PEDOT) and reduced graphite oxide (rGO) striped microelectrode arrays were fabricated by lithography technology. It has been demonstrated that the organic bioelectronic devices can be used to spatially and temporally manipulate the location and proliferation of the neuron-like pheochromocytoma cells (PC-12 cells).

METHODS

By coating an electrically labile contact repulsion layer of poly(l-lysine-graft-ethylene glycol) (PLL-g-PEG) on the PEDOT electrode, the location and polarity of the PC-12 cells were confined to the rGO electrodes.

RESULTS

The outgrowth of spatially confined bipolar neurites was found to align along the direction of the 20μm wide electrode. The location of the PC-12 cells can also be manipulated temporally by applying electrical stimulation during the neurite differentiation of PC-12 cells, allowing the PC-12 cells to cross over the boundary between the PEDOT and the rGO regions and construct neurite networks in an unconfined manner where the contact repulsive coating of PLL-g-PEG was removed.

CONCLUSIONS

This adsorption and desorption of the PLL-g-PEG without and with electrical stimulation can be attributed to the tunable surface properties of the PEDOT microelectrodes, whose surface charge can switch from being negative to positive under electrical stimulation.

GENERAL SIGNIFICANCE

The electrically tunable organic bioelectronics reported here could potentially be applied to tissue engineering related to the development and regeneration of mammalian nervous systems. The spatial and temporal control in this device would also be used to study the synapse junctions of neuron-neuron contacts in both time and space domains. This article is part of a Special Issue entitled Organic Bioelectronics - Novel Applications in Biomedicine.

Directed differentiation of embryonic P19 cells and neural stem cells into neural lineage on conducting PEDOT-PEG and ITO glass substrates

Differentiation of pluripotent and lineage restricted stem cells such as neural stem cells (NSCs) was studied on conducting substrates of various nature without perturbation of the genome with exogenous genetic material or chemical stimuli. Primary mouse adult neural stem cells (NSCs) and P19 pluripotent embryonal (P19 EC) carcinoma cells were used. Expression levels of neuronal markers β-III-tubulin and neurofilament were evaluated by immunochemistry and flow cytometry. It was shown that the ability of the substrate to induce differentiation directly correlated with its conductivity. Conducting substrates (conducting oxides or doped π-conjugated organic polymers) with different morphology, structure, and conductivity mechanisms all promoted differentiation of NSC and P19 cells into neuronal lineage to a similar degree without use of additional factors such as poly-L-ornithine coating or retinoic acid, as verified by their morphology and upregulation of the neuronal markers but not astrocyte marker GFAP. However, substrates with low conductance below ca. 10(-4) S cm(-2) did not show this ability. Morphology of differentiating cells was visualized by atomic force microscopy. NSCs cells increased β-III-tubulin expression by 95% and P19 cells by over 30%. Our results suggest that the substrate conductivity is a key factor governing the cell fate. Differentiation of P19 cells into neuronal lineage on conducting substrates was attributed to downregualtion of Akt signaling pathway and increase in expression of dual oxidase 1 (DUOX 1).