Swollen liquid-crystalline lamellar phase based on extended solid-like sheets

Temperature-Enhanced Ordering in Plate-like Semicrystalline Block Copolymer Single-Crystal Suspensions Studied by Real-Time SAXS/WAXS

Self-assembly of hard platelet colloids into liquid crystalline phases is typically driven by entropy, making them less sensitive to temperature changes. However, soft interaction potentials often exist in real colloidal systems, which can lead to temperature-sensitive phase transitions. Despite significant progress in understanding phase behavior in the past 2 decades, studies on temperature-dependent phase behavior remain rare, and there is limited knowledge about how soft interactions influence phase transitions upon temperature changes. In this work, we investigated a platelet colloid system in isotropic and nematic phases using small- and wide-angle X-ray scattering techniques (SAXS/WAXS) and polarized optical microscopy (POM). The system consisted of polystyrene-block-poly(l-lactide) (PS-b-PLLA) block copolymer single crystals (BCSCs) with varying sizes dispersed in p-xylene. These crystals were truncated lozenge-shaped with effective diameters of 500 and 1000 nm and a uniform dry thickness of 18.0 nm. The ordering behaviors of BCSC500 in the isotropic phase and BCSC1000 in the N phase were monitored through SAXS/WAXS during heating, quenching, self-seeding, crystal growth, and final quenching. Enhanced ordering, specifically face-to-face correlation, was observed during heating prior to crystal melting. For BCSC500, ordering emerged at 105 °C during heating. In the case of BCSC1000 in the N phase, ordering was enhanced with increased heating and reached up to the ninth order of correlation peaks, indicating the formation of lamellar domains within the N phase. After seeding and crystal growth, both systems exhibited ordering. However, during the final cooling to room temperature, ordering disappeared for BCSC500 but persisted for BCSC1000. POM observations revealed that for both systems, initial heating resulted in a decrease in overall brightness; however, enhanced nematic domains or tactoids emerged prior to melting. Subsequent thermal treatments did not induce noticeable changes in the observed order. While both techniques revealed increased order, discrepancies were noted. SAXS indicated intensified short-range correlations, while POM showed the formation of local nematic domains or tactoids. We propose three distinct ordering regimes to reconcile these observations: large-scale nematic order, enhanced short-range order, and short-range clusters. We attributed the temperature-enhanced ordering phenomenon to lateral interactions between the BCSCs, annealing, and memory effects during melting and crystallization.

Capacitance enhancement by ion-laminated borophene-like layered materials

Atomically flat two-dimensional networks of boron are attracting attention as post-graphene materials. An introduction of cations between the boron atomic layers can exhibit unique electronic functions that are not achieved by neutral graphene or its derivatives. In the present study, we propose a synthesis strategy for ion-laminated boron layered materials in a solution phase, which enables the preparation of analogs by changing the alkali-metal species. The introduction of large cations extends the thermal range of the liquid-crystal phases because of weakened ionic interactions between borophene-like layers. An investigation of the capacitance of ion-laminated structures revealed a 105-fold or better increase in capacitance when the borophene-like materials were introduced between electrodes. That is difficult for general materials since the dielectric constant of common materials is below several thousand.

2D Photonic Colloidal Liquid Crystals Composed of Self-Assembled Rod-Shaped Particles

Photonic crystals, characterized by their periodic structures, have been extensively studied for their ability to manipulate light. Typically, the development of 2D photonic crystals requires either sophisticated equipment or precise orientation of spherical nanoparticles. However, liquid-crystalline (LC) materials offer a promising alternative, facilitating the formation of periodic structures without the need for complex manipulation. Despite this advantage, the development of 2D photonic periodic structures using LC materials is limited to a few colloidal nanodisk liquid crystals. Herein, 2D photonic colloidal liquid crystals composed of biomineral-based nanorods and water is reported. The soft photonic materials with 2D structure by self-assembled LC colloidal nanorods are unique and a new class of photonic materials different from conventional solid 2D photonic materials. These colloids exhibit bright structural colors with high reflectance (>50%) and significant angular dependency. The structural colors are adjusted by controlling the concentration and size of the LC colloidal nanorods. Furthermore, mechanochromic hydrogel thin films with 2D photonic structure are developed. The hydrogels exhibit reversible mechanochromic properties with angular dependency, which can be used for an advanced stimuli responsible sensor.

Time evolution of the inner structure of antimony phosphate nanosheet suspension developing structural colouration

Structural colouration observed in antimony phosphate nanosheet suspensions has been known for two decades, but the stability of their inner structures has not been a topic in colloidal nanosheet systems. In this study, we investigate the time evolution of structures in suspension using UV-visible spectrometry and small-angle X-ray scattering. Here, we report that antimony phosphate nanosheet systems re-organise their inner structures, especially at lower concentrations (isotropic or biphasic region), and that the basal spacing decreases with time after sample preparation, although the evolution speed depends on the sample concentration. The stability of the inner structure of the suspension is essential for their application as structural colour materials in sensors and colourants.

Liquid-Crystalline Photonic Sandwich: Electroresponsive Colloids of Clay Nanosheets Loading Photofunctional Dyes

Colloidal clay nanosheets obtained by the delamination of layered crystals of smectite-type clay minerals in water form liquid crystals because of their shape anisotropy. Loading of organic dyes onto the liquid crystalline clay nanosheets will enable novel photonic materials, where photofunctions of the loaded dye are controlled by the liquid crystallinity of the clay nanosheets. However, adsorption of organic dyes onto the nanosheets renders the nanosheet surfaces hydrophobic, and consequently, colloidal stability of the nanosheets is lost. In this study, this drawback is overcome by sandwiching cationic stilbazolium dyes between a pair of synthetic fluorohectorite nanosheets. This is realized by the preparation of stilbazolium-clay second-stage intercalation compounds characterized by intercalation of dye cations into every other interlayer space of the hectorite clay, where nonintercalated interlayer spaces are occupied by Na+ ions. The second-stage intercalation compounds are obtained by partial ion exchange of mother clay mineral incorporating Na+ ions in all of the interlayer spaces and delaminated from the Na+-containing interlayer spaces to form clay nanosheets sandwiching the dye molecules. Aqueous colloids of the dye-sandwiching clay nanosheets form colloidal liquid crystals, and the dye-sandwiching liquid crystalline clay nanosheets respond to an applied AC electric field to be aligned parallel to the electric field. The assembled structure of the dye-sandwiching clay nanosheets under the electric field is characterized by aligned discrete clay platelets, which is somewhat different from that of a colloidal liquid crystal of clay nanosheets without dye loading characterized by macroscopic liquid crystalline domains up to submillimeters. The electric alignment of the clay nanosheets induces alteration of light absorption of the sandwiched stilbazolium molecules, which verifies a strategy of constructing stimuli-responsive photonic materials of clay-organic hybrids.

Forceless spontaneous delamination of high-aspect ratio fluorohectorite into monolayer nanosheets in chloroform

One-dimensional dissolution of a layered compound in a nonpolar organic solvent is reported for the first time. A high-aspect ratio fluorohectorite modified with a cationic surfactant (dioctadecyldimethylammonium) showed spontaneous delamination into monolayer nanosheets in chloroform.

Monodisperse nanosheet mesophases

Self-assemblies of anisotropic colloidal particles into colloidal liquid crystals and well-defined superlattices are of great interest for hierarchical nanofabrications that are applicable for various functional materials. Inorganic nanosheets obtained by exfoliation of layered crystals have been highlighted as the intriguing colloidal units; however, the size polydispersity of the nanosheets has been preventing precise design of the assembled structures and their functions. Here, we demonstrate that the anionic titanate nanosheets with monodisperse size reversibly form very unusual superstructured mesophases through finely tunable weak attractive interactions between the nanosheets. Transmission electron microscopy, polarizing optical microscopy, small-angle x-ray scattering, and confocal laser scanning microscopy clarified the reversible formation of the mesophases (columnar nanofibers, columnar nematic liquid crystals, and columnar nanofiber bundles) as controlled by counter cations, nanosheet concentration, solvent, and temperature.

A magnetically responsive photonic crystal of graphene oxide nanosheets

Magnetically responsive photonic crystals of colloidal nanosheets hold great promise for various applications. Here, we systematically investigated the magnetically responsive behavior of a photonic crystal consisting of graphene oxide (GO) nanosheets and water. After applying a 12 T magnetic field perpendicular and parallel to the observation direction, the photonic crystal exhibited a more vivid structural color and no structural color, respectively, based on the magnetic orientation of GO nanosheets. The reflection wavelength can be modulated by varying the GO concentration, and the peak intensity can be basically enhanced by increasing both the time and strength of the magnetic application. To improve color quality, we developed a novel approach of alternately applying a magnetic field to two orthogonal directions, instead of using a rotating magnetic field. Finally, we achieved color switching by changing the direction of applied magnetic fields.

Magnetic field-responsive graphene oxide photonic liquids

Modifying the environment around particles (e.g., introducing a secondary phase or external field) can affect the way they interact and assemble, thereby giving control over the physical properties of a dynamic system. Here, graphene oxide (GO) photonic liquids that respond to a magnetic field are demonstrated for the first time. Magnetic nanoparticles are used to provide a continuous magnetizable liquid environment around the GO liquid crystalline domains. In response to a magnetic field, the alignment of magnetic nanoparticles, coupled with the diamagnetic property of GO nanosheets, drives the reorientation and alignment of the nanosheets, enabling switchable photonic properties using a permanent magnet. This phenomenon is anticipated to be extendable to other relevant photonic systems of shape-anisotropic nanoparticles and may open up opportunities for developing GO-based optical materials and devices.

Crystalline restacking of 2D-materials from their nanosheets suspensions

We report here the highly ordered restacking of the layered phosphatoantimonic dielectric materials H3(1-x)M3xSb3P2O14, (where M = Li, Na, K, Rb, Cs and 0 ≤ x ≤ 1), from their nanosheets dispersed in colloidal suspension, induced by a simple pH change using alkaline bases. H3Sb3P2O14 aqueous suspensions are some of the rare examples of colloidal suspensions based on 2D materials exhibiting a lamellar liquid crystalline phase. Because the lamellar period can reach several hundred nanometers, the suspensions show vivid structural colors and because these colors are sensitive to various chemicals, the suspensions can be used as sensors. The structures of the lamellar liquid crystalline phase and the restacked phase have been studied by X-ray scattering (small and wide angle), which has followed the dependence of the lamellar/restacked phase equilibrium on the cation exchange rate, x. The X-ray diffraction pattern of the restacked phase is almost identical to that of the M3Sb3P2O14 crystalline phase, showing that the restacking is highly accurate and avoids the turbostratic disorder of the nanosheets classically observed in nanosheet stacking of other 2D materials. Strikingly, the restacking process exhibits features highly reminiscent of a first-order phase transition, with the existence of a phase coexistence region where both ∼1 nm (interlayer spacing of the restacked phase) and ∼120 nm lamellar periods can be observed simultaneously. Furthermore, this first-order phase transition is well described theoretically by incorporating a Lennard-Jones-type lamellar interaction potential into an entropy-based statistical physics model of the lamellar phase of nanosheets. Our work shows that the precise cation exchange produced at room temperature by a classical neutralization reaction using alkaline bases leads to a crystal-like restacking of the exfoliated free Sb3P2O143- nanosheets from suspension, avoiding the turbostratic disorder typical of van der Waals 2D materials, which is detrimental to the controlled deposition of nanosheets into complex integrated electronic, spintronic, photonic or quantum structures.

Experimental probing of dynamic self-organized columnar assemblies in colloidal liquid crystals

Self-organized supramolecular assemblies are widespread in nature and technology in the form of liquid crystals, colloids, and gels. The reversible nature of non-covalent bonding leads to dynamic functions such as stimuli-responsive switching and self-healing, which are unachievable from an isolated molecule. However, multiple intermolecular interactions generate diverse conformational and configurational molecular motions over various time scales in their self-assembled states, and their specific dynamics remains unclear. In the present study, we have experimentally unveiled the static structures and dynamical behaviors in columnar colloidal liquid crystals by a coherent X-ray scattering technique using refined model samples. We have found that controlling the size distribution of the colloidal nanoplates dramatically changed their static and dynamic properties. Furthermore, the resulting dynamical behaviors obtained by X-ray photon correlation spectroscopy have been successfully decomposed into multiple distinct modes, allowing us to explore the dynamical origin in the colloidal liquid-crystalline state. The present approaches using a columnar liquid crystal may contribute to a better understanding of the dynamic nature of molecular assemblies and dense colloidal systems and bring valuable insights into rational design of functional properties of self-assembled materials such as stimuli-responsive liquid crystals, self-healing gels, and colloidal crystals. For these materials, the motion of constituent particles and molecules in the self-assembled state is a key factor for structural formation and dynamically responsive performance.

Fabrication of Bragg stack films of clay nanosheets and polycations via co-polymerization of intercalated monomers and functional interlayer cations

The fabrication of one-dimensional (1D) crystalline, monodomain nanocomposite films (hybrid Bragg stacks) is still limited to a few combinations of polymers and clay. The main reason is the segregation of clay and polymers driven by the entropic loss faced by the polymer confined in a narrow slit between the nanosheets. By exchanging synthetic sodium-fluorohectorite with vinylbenzyltrimethylammonium chloride, we succeeded in delaminating clay via 1D dissolution in N-methylformamide to obtain a liquid crystalline suspension. By combining this with bisphenol A glycerolate diacrylate, 1D crystalline nanocomposites could be obtained via photopolymerization of doctor bladed wet coatings. Infrared spectroscopy confirmed the co-polymerization of monomers and the organic modifier between the hectorite platelets. This single-phase hybrid material shows very low oxygen and water vapor transmission rates. The incorporation of the modified clay into the polymer leads to an oxygen transmission rate of 0.21 cm³ m^-2 day^-1 atm^-1 at 50% r.h. and 23 °C and a water vapor transmission rate of 0.05 g m^-2 day^-1 for a coating of 3.7 μm, making this material appropriate for challenging packaging applications.

Deep ultraviolet hydrogel based on 2D cobalt-doped titanate

Birefringent optical elements that work in deep ultraviolet (DUV) region become increasingly important these years. However, most of the DUV optical elements have fixed birefringence which is hard to be tuned. Here, we invent a birefringence-tunable optical hydrogel with mechano-birefringence effect in the DUV region, based on two-dimensional (2D) low-cobalt-doped titanate. This 2D oxide material has an optical anisotropy factor of 1.5 × 10^-11 C² J^-1 m^-1, larger than maximum value obtained previously, leading to an extremely large specific magneto-optical Cotton-Mouton coefficient of 3.9 × 10⁶ T^-2 m^-1. The extremely large coefficient enables the fabrication of birefringent hydrogel in a small magnetic field with an ultra-low concentration of 2D oxide material. The hydrogel can stably and continuously modulate 303 nm DUV light with large phase tunability by varying the strain (compression or stretching) from 0 to 50%. Our work opens the door to design and fabricate new proof-of-concept DUV birefringence-tunable element, as demonstrated by optical hydrogels capable of DUV modulation by mechanical stimuli.

Do Aqueous Suspensions of Smectite Clays Form a Smectic Liquid-Crystalline Phase?

Bottom-up strategies for the production of well-defined nanostructures often rely on the self-assembly of anisotropic colloidal particles (nanowires and nanosheets). These building blocks can be obtained by delamination in a solvent of low-dimensionality crystallites. To optimize particle availability, determination of the delamination mechanism and the different organization stages of anisotropic particles in dispersion is essential. We address this fundamental issue by exploiting a recently developed system of fluorohectorite smectite clay mineral that delaminates in water, leading to colloidal dispersions of single-layer, very large (≈20 μm) clay sheets at high dilution. We show that when the clay crystallites are dispersed in water, they swell to form periodic one-dimensional stacks of fluorohectorite sheets with very low volume fraction (<1%) and therefore huge (≈100 nm) periods. Using optical microscopy and synchrotron X-ray scattering, we establish that these colloidal stacks bear strong similarities, yet subtle differences, with a smectic liquid-crystalline phase. Despite the high dilution, the colloidal stacks of sheets, called colloidal accordions, are extremely robust mechanically and can persist for years. Moreover, when subjected to AC electric fields, they rotate as solid bodies, which demonstrates their outstanding internal cohesion. Furthermore, our theoretical model captures the dependence of the stacking period on the dispersion concentration and ionic strength and explains, invoking the Donnan effect, why the colloidal accordions are kinetically stable over years and impervious to shear and Brownian motion. Because our model is not system specific, we expect that similar colloidal accordions frequently appear as an intermediate state during the delamination process of two-dimensional crystals in polar solvents.

Delamination by Repulsive Osmotic Swelling of Synthetic Na-Hectorite with Variable Charge in Binary Dimethyl Sulfoxide-Water Mixtures

Swelling of clays is hampered by increasing layer charge. With vermiculite-type layer charge densities, crystalline swelling is limited to the two-layer hydrate, while osmotic swelling requires ion exchange with bulky and hydrophilic organic molecules or with Li⁺ cations to trigger repulsive osmotic swelling. Here, we report on surprising and counterintuitive osmotic swelling behavior of a vermiculite-type synthetic clay [Na_0.7]^inter[Mg_2.3Li_0.7]^oct[Si₄]^tetO₁₀F₂ in mixtures of water and dimethyl sulfoxide (DMSO). Although swelling in pure water is restricted to crystalline swelling, with the addition of DMSO, osmotic swelling sets in at some threshold composition. Finally, when the DMSO concentration is increased further to 75 vol %, swelling is restricted again to crystalline swelling as expected. Repulsive osmotic swelling thus is observed in a narrow composition range of the binary water-DMSO mixture, where a freezing point suppression is observed. This suppression is related to DMSO and water molecules exhibiting strong interactions leading to stable molecular clusters. Based on this phenomenological observation, we hypothesize that the unexpected swelling behavior might be related to the formation of different complexes of interlayer cations being formed at different compositions. Powder X-ray diffraction and ²³Na magic angle spinning-NMR evidence is presented that supports this hypothesis. We propose that the synergistic solvation of the interlayer sodium at favorable compositions exerts a steric pressure by the complexes formed in the interlayer. Concomitantly, the basal spacing is increased to a level, where entropic contributions of interlayer species lead to a spontaneous thermodynamically allowed one-dimensional dissolution of the clay stack.

Multiresponsive Polymer Nanocomposite Liquid Crystals Having Heterogeneous Phase Transitions for Battery-Free Temperature Maintenance Indicators

Multiresponsive functional materials that respond to more than one external stimulus are promising for novel photonic, electronic, and biomedical applications. However, the design or synthesis of new multiresponsive materials is challenging. Here, this work reports a facile method to prepare a multiresponsive colloidal material by mixing a liquid-crystalline 2D nanocolloid and a functional polymer colloid. For this purpose, electrically sensitive exfoliated α-ZrP 2D nanocolloids and thermosensitive block copolymer colloids that are dispersed well in water are mixed. In the liquid-crystalline nanocomposite, nematic, antinematic, or isotropic assemblies of α-ZrP, nanoparticles can be electrically and selectively obtained by applying electric fields with different frequencies; furthermore, their rheology is thermally and reversibly controlled through thesol-gel-sol transition. The nanocomposite exhibits a solid gel phase within a predesigned gel temperature range and a liquid sol phase outside this range. These properties facilitate the design of a simple display device in which information can be electrically written and thermally stabilized or erased, and using the device, a battery-free temperature maintenance indication function is demonstrated. The proposed polymer nanocomposite method can enrich the physical properties of 2D nanocolloidal liquid crystals and create new opportunities for eco-friendly, reusable, battery-free electro-optical devices.

Advanced Functional Liquid Crystals

Liquid crystals have been intensively studied as functional materials. Recently, integration of various disciplines has led to new directions in the design of functional liquid-crystalline materials in the fields of energy, water, photonics, actuation, sensing, and biotechnology. Here, recent advances in functional liquid crystals based on polymers, supramolecular complexes, gels, colloids, and inorganic-based hybrids are reviewed, from design strategies to functionalization of these materials and interfaces. New insights into liquid crystals provided by significant progress in advanced measurements and computational simulations, which enhance new design and functionalization of liquid-crystalline materials, are also discussed.

Nematic suspension of a microporous layered silicate obtained by forceless spontaneous delamination via repulsive osmotic swelling for casting high-barrier all-inorganic films

Exploiting the full potential of layered materials for a broad range of applications requires delamination into functional nanosheets. Delamination via repulsive osmotic swelling is driven by thermodynamics and represents the most gentle route to obtain nematic liquid crystals consisting exclusively of single-layer nanosheets. This mechanism was, however, long limited to very few compounds, including 2:1-type clay minerals, layered titanates, or niobates. Despite the great potential of zeolites and their microporous layered counterparts, nanosheet production is challenging and troublesome, and published procedures implied the use of some shearing forces. Here, we present a scalable, eco-friendly, and utter delamination of the microporous layered silicate ilerite into single-layer nanosheets that extends repulsive delamination to the class of layered zeolites. As the sheet diameter is preserved, nematic suspensions with cofacial nanosheets of ≈9000 aspect ratio are obtained that can be cast into oriented films, e.g., for barrier applications.

Angular-Independent Structural Colors of Clay Dispersions

Clay mineral nanosheet colloids were found to show angular-independent structural colors after desalting. Naked-eye observation and UV-visible reflectance spectra showed that the color is tuned by varying the average nanosheet size and nanosheet concentration. The low angular-dependence of the structural color was also clarified by these observations, which is the first case for a nanosheet system. The present system is expected as an environmentally benign and low-cost structural color material for various applications.

Stable graphene oxide hydrophobic photonic liquids

Graphene oxide (GO) is an important nanomaterial for producing photonic liquids due to its ability to display full-color reflections in water. However, the poor stability of GO photonic liquids and unsatisfactory dispersibility of GO nanosheets in hydrophobic liquid media have been significant drawbacks to developing photonic materials based on GO. Here, stable GO hydrophobic photonic liquids are demonstrated for the first time. GO nanosheets are directed into different hydrophobic liquid media, including reactive liquid precursors like tetraethoxysilane and ethyl acrylate, in the presence of phase transfer additives. These liquids exhibit tunable reflection wavelength up to ∼1300 nm with improved stability relative to aqueous GO photonic suspensions at elevated temperatures or under ambient conditions. Supported by an entropy-driven depletion mechanism, hydrophobic additives can effectively mediate the self-assembly of GO to produce tunable photonic liquids without the need to adjust GO concentrations. Furthermore, simultaneous infrared and visible light reflection can be achieved, enabling infrared photonic GO liquids to display visible colors. The improved stability and tunable photonic properties of hydrophobic GO liquids will open a way for developing GO-based optical materials and devices.

Bright, noniridescent structural coloration from clay mineral nanosheet suspensions

Structural colors originate by constructive interference following reflection and scattering of light from nanostructures with periodicity comparable to visible light wavelengths. Bright and noniridescent structural colorations are highly desirable. Here, we demonstrate that bright noniridescence structural coloration can be easily and rapidly achieved from suspended two-dimensional nanosheets of a clay mineral. We show that brightness is enormously improved by using double clay nanosheets, thus optimizing the clay refractive index that otherwise hampers structural coloration from such systems. Intralayer distances, and thus the structural colors, can be precisely and reproducibly controlled by clay concentration and ionic strength independently, and noniridescence is readily and effortlessly obtained in this system. Embedding such clay-designed nanosheets in recyclable solid matrices could provide tunable vivid coloration and mechanical strength and stability at the same time, thus opening a previously unknown venue for sustainable structural coloration.

Fine tuning the structural colours of photonic nanosheet suspensions by polymer doping

Aqueous suspensions of nanosheets are readily obtained by exfoliating low-dimensional mineral compounds like H₃Sb₃P₂O₁₄. The nanosheets self-organize, at low concentration, into a periodic stack of membranes, i.e. a lamellar liquid-crystalline phase. Due to the dilution, this stack has a large period of a few hundred nanometres, it behaves as a 1-dimensional photonic material and displays structural colours. We experimentally investigated the dependence of the period on the nanosheet concentration. We theoretically showed that it cannot be explained by the usual DLVO interaction between uniform lamellae but that the particulate nature of nanosheet-laden membranes must be considered. Moreover, we observed that adding small amounts of 100 kDa poly(ethylene oxide) (PEO) decreases the period and allows tuning the colour throughout the visible range. PEO adsorbs on the nanosheets, inducing a strong reduction of the nanosheet charge. This is probably due to the Lewis-base character of the EO units of PEO that become protonated at the low pH of the system, an interpretation supported by theoretical modeling. Oddly enough, adding small amounts of 1 MDa PEO has the opposite effect of increasing the period, suggesting the presence of an additional intermembrane repulsion not yet identified. From an applied perspective, our work shows how the colours of these 1-dimensional photonic materials can easily be tuned not only by varying the nanosheet concentration (which might entail a phase transition) but also by adding PEO. From a theoretical perspective, our approach represents a necessary step towards establishing the phase diagram of aqueous suspensions of charged nanosheets.

Gold-clay nanocomposite colloids with liquid-crystalline and plasmonic properties

Imparting liquid-crystal (LC) materials with the plasmonic properties of metal nanoparticles is actively pursued for applications. We achieved this goal by synthetizing gold nanoparticles onto clay nanosheets, leading to nematic nanocomposite suspensions. Optical observations and structural analysis show the growth of the gold nanoparticles without altering the LC properties of the nanosheets. These colloids display plasmonic structural colours and they can be aligned by an electric field, which is relevant for fundamental and materials chemistry of colloidal LC.

Assembly of cellulose nanocrystals and clay nanoplatelets studied by time-resolved X-ray scattering

Time-resolved small-angle X-ray scattering (SAXS) was used to probe the assembly of cellulose nanocrystals (CNC) and montmorillonite (MNT) over a wide concentration range in aqueous levitating droplets. Analysis of the SAXS curves of the one-component and mixed dispersions shows that co-assembly of rod-like CNC and MNT nanoplatelets is dominated by the interactions between the dispersed CNC particles and that MNT promotes gelation and assembly of CNC, which occurred at lower total volume fractions in the CNC:MNT than in the CNC-only dispersions. The CNC dispersions displayed a d ∝ φ-1/2 scaling and a low-q power-law exponent of 2.0-2.2 for volume fractions up to 35%, which indicates that liquid crystal assembly co-exists and competes with gelation.

Tuning the photonic properties of graphene oxide suspensions with nanostructured additives

Photonic materials that can selectively reflect light across the visible spectrum are valuable for applications in optical devices, sensors, and decoration. Although two-dimensional (2D) colloids that stack into layers with spacing of hundreds of nanometers are able to selectively diffract light, controlling their separation in solution has proven challenging. In this work, we investigate the role of additives to control the photonic properties of hybrid colloidal suspensions of graphene oxide (GO). We discovered that low concentrations of colloidal additives like cellulose nanocrystals (CNCs) and clay nanoparticles (hectorite) added to GO suspensions lead to dramatic color changes. These hybrid colloidal suspensions demonstrate tunable structural colors and temperature-sensitive properties that likely originate from the entropically driven ejection of guests between the sheets, and from the interactions between colloidal electrical double layers and additional counterions. On the other hand, blending polymeric or molecular additives with GO suspensions either deteriorates or does not impact the photonic properties. These results are helpful to understand the interaction between GO suspensions and additives over different length scales, and open a path to advancing photonic materials based on hybrid colloidal suspensions.

Perovskite Nanosheet Hydrogels with Mechanochromic Structural Color

Structural color colloidal sols of perovskite nanosheets were synthesized and were immobilized in a polymer hydrogel film by in situ photopolymerization, leading to a novel mechanochromic material. Visible absorption spectroscopy, polarized optical microscopy and small-angle X-ray scattering revealed that the nanosheets are aligned parallel to the film surface with the periodic distance of up to ca. 300 nm, giving the structural color tunable over full color range. The present structural color gel showed reversible mechanochromic response that detects weak stress of 1 kPa with the quick response time less than 1 ms as well as high mechanical toughness (compressive breaking stress of up to 3 MPa). These excellent properties are suitable for applications for mechano-sensors and displays.

Nanoparticles Supported on Sub-Nanometer Oxide Films: Scaling Model Systems to Bulk Materials

Ultrathin layers of oxides deposited on atomically flat metal surfaces have been shown to significantly influence the electronic structure of the underlying metal, which in turn alters the catalytic performance. Upscaling of the specifically designed architectures as required for technical utilization of the effect has yet not been achieved. Here, we apply liquid crystalline phases of fluorohectorite nanosheets to fabricate such architectures in bulk. Synthetic sodium fluorohectorite, a layered silicate, when immersed into water spontaneously and repulsively swells to produce nematic suspensions of individual negatively charged nanosheets separated to more than 60 nm, while retaining parallel orientation. Into these galleries oppositely charged palladium nanoparticles were intercalated whereupon the galleries collapse. Individual and separated Pd nanoparticles were thus captured and sandwiched between nanosheets. As suggested by the model systems, the resulting catalyst performed better in the oxidation of carbon monoxide than the same Pd nanoparticles supported on external surfaces of hectorite or on a conventional Al2 O3 support. XPS confirmed a shift of Pd 3d electrons to higher energies upon coverage of Pd nanoparticles with nanosheets to which we attribute the improved catalytic performance. DFT calculations showed increasing positive charge on Pd weakened CO adsorption and this way damped CO poisoning.

Nanopartikel auf subnanometer dünnen oxidischen Filmen: Skalierung von Modellsystemen

Durch die Abscheidung von ultradünnen Oxidschichten auf atomar‐flachen Metalloberflächen konnte die elektronische Struktur des Metalls und hierdurch dessen katalytische Aktivität beeinflusst werden. Die Skalierung dieser Architekturen für eine technische Nutzbarkeit war bisher aber kaum möglich. Durch die Verwendung einer flüssigkristallinen Phase aus Fluorhectorit‐Nanoschichten, können wir solche Architekturen in skalierbarem Maßstab imitieren. Synthetischer Natriumfluorhectorit (NaHec) quillt spontan und repulsiv in Wasser zu einer nematischen flüssigkristallinen Phase aus individuellen Nanoschichten. Diese tragen eine permanente negative Schichtladung, sodass selbst bei einer Separation von über 60 nm eine parallele Anordnung der Schichten behalten wird. Zwischen diesen Nanoschichten können Palladium‐Nanopartikel mit entgegengesetzter Ladung eingelagert werden, wodurch die nematische Phase kollabiert und separierte Nanopartikel zwischen den Schichten fixiert werden. Die Aktivität zur CO‐Oxidation des so entstandenen Katalysators war höher als z. B. die der gleichen Nanopartikel auf konventionellem Al2O3 oder der externen Oberfläche von NaHec. Durch Röntgenphotoelektronenspektroskopie konnte eine Verschiebung der Pd‐3d‐Elektronen zu höheren Bindungsenergien beobachtet werden, womit die erhöhte Aktivität erklärt werden kann. Berechnungen zeigten, dass mit erhöhter positiver Ladung des Pd die Adsorptionsstärke von CO erniedrigt und damit auch die Vergiftung durch CO vermindert wird.

Enhancing the Catalytic Activity of Palladium Nanoparticles via Sandwich-Like Confinement by Thin Titanate Nanosheets

As atomically thin oxide layers deposited on flat (noble) metal surfaces have been proven to have a significant influence on the electronic structure and thus the catalytic activity of the metal, we sought to mimic this architecture at the bulk scale. This could be achieved by intercalating small positively charged Pd nanoparticles of size 3.8 nm into a nematic liquid crystalline phase of lepidocrocite-type layered titanate. Upon intercalation the galleries collapsed and Pd nanoparticles were captured in a sandwichlike mesoporous architecture showing good accessibility to Pd nanoparticles. On the basis of X-ray photoelectron spectroscopy (XPS) and CO diffuse reflectance Fourier transform infrared spectroscopy (DRIFTS) Pd was found to be in a partially oxidized state, while a reduced Ti species indicated an electronic interaction between nanoparticles and nanosheets. The close contact of titanate sandwiching Pd nanoparticles, moreover, allows for the donation of a lattice oxygen to the noble metal (inverse spillover). Due to the metal-support interactions of this peculiar support, the catalyst exhibited the oxidation of CO with a turnover frequency as high as 0.17 s-1 at a temperature of 100 °C.

Nematic Phase of Plate-like Semicrystalline Block Copolymer Single Crystals in Solution Studied by Small-Angle X-Ray Scattering

Crystalline block copolymers have been used to prepare plate-like colloidal systems with well-controlled size, shape, and size distribution. The isotropic-to-nematic (I-N) phase transition of the novel plate-like colloidal particle suspensions has been reported previously. In this work, we focus on the characterization of the solution structure of the crystals and the N-phase using small- and ultrasmall-angle X-ray scattering techniques (SAXS/USAXS). The system has polystyrene-block-poly(l-lactide) (PS-b-PLLA) block copolymer single crystals (BCSCs) with different sizes dispersed in p-xylene. These crystals are truncated lozenge in shape and have effective diameters ranging from 550 to 4000 nm with a uniform dry thickness of 18.0 nm. Scattering of the individual crystal in solution can be simplified using a disc model with a core layer of 9-10 nm due to the lower contrast of the tethered PS layer. BCSC suspensions filled in thin quartz capillaries are prepared for monitoring the structural information. SAXS measurements of the isotropic phase show a strong face-to-face correlation, indicating that platelets form small stacked clusters in solutions. The isotropic phase is thus a coexistence of single crystals and the stacked multiple-layered clusters. The face-to-face spacing, d, in the N phases is around 75-90 nm, which increases slightly upon increasing the size of crystals. For a given system, the spacing does not change with increasing concentration under the current experimental conditions. Finally, the possible formation of lamellar domains within the N phase is also discussed due to the lateral attraction of this system. These results demonstrate the importance of the lateral attraction between the polar crystalline PLLA blocks on the formation of the N phase: the BCSCs self-assemble into larger sheets via the lateral attraction, which further enhances the I-N transition.

Osmotic Delamination: A Forceless Alternative for the Production of Nanosheets Now in Highly Polar and Aprotic Solvents

Repulsive osmotic delamination is thermodynamically allowed "dissolution" of two-dimensional (2D) materials and therefore represents an attractive alternative to liquid-phase exfoliation to obtain strictly monolayered nanosheets with an appreciable aspect ratio with quantitative yield. However, osmotic delamination was so far restricted to aqueous media, severely limiting the range of accessible 2D materials. Alkali-metal intercalation compounds of MoS₂ or graphite are excluded because they cannot tolerate even traces of water. We now succeeded in extending osmotic delamination to polar and aprotic organic solvents. Upon complexation of interlayer cations of synthetic hectorite clay by crown ethers, either 15-crown-5 or 18-crown-6, steric pressure is exerted, which helps in reaching the threshold separation required to trigger osmotic delamination based on translational entropy. This way, complete delamination in water-free solvents like aprotic ethylene and propylene carbonate, N-methylformamide, N-methylacetamide, and glycerol carbonate was achieved.

Two-Dimensional Molecular Sheets of Transition Metal Oxides toward Wearable Energy Storage

Flexible and wearable electronics have recently sparked intense interest in both academia and industry because they can greatly revolutionize human lives by impacting every aspect of our daily routine. Therefore, developing compatible energy storage devices has become one of the most important research frontiers in this field. Particularly, the development of flexible electrodes is of great significance when considering their essential role in the performance of these devices. Although there is no doubt that transition metal oxide nanomaterials are suitable for providing electrochemical energy storage, individual oxides generally cannot be developed into freestanding electrodes because of their intrinsically low mechanical strength.Two-dimensional sheets with genuine unilamellar thickness are perfect units for the assembly of freestanding and mechanically flexible devices, as they have the advantages of low thickness and good flexibility. Therefore, the development of metal oxide materials into a two-dimensional sheet morphology analogous to graphene is expected to solve the above-mentioned problems. In this Account, we summarize the recent progress on two-dimensional molecular sheets of transition metal oxides for wearable energy storage applications. We start with our understanding of the principle of producing two-dimensional metal oxides from their bulk-layered counterparts. The unique layered structure of the precursors inspired the exploration of their interlayer chemistry, which helps us to understand the processes of swelling and delamination. Rational methods for tuning the chemical composition, size/thickness, and surface chemistry of the obtained nanosheets and how physicochemical properties of the nanosheets can be modulated are then briefly introduced. Subsequently, the orientational alignment of the anisotropic sheets and the origins of their liquid-crystalline characteristics are discussed, which are of vital importance for their subsequent macroscopic assembly. Finally, macroscopic electrodes with geometric diversity ranging from one-dimensional macroscopic fibers to two-dimensional films/papers and three-dimensional monolithic foams are summarized. The intrinsically low mechanical stiffness of metal oxide sheets can be effectively overcome by wisely designing the assembly mode and sheet interfaces to obtain decent mechanical properties integrated with superior electrochemical performance, thereby providing critical advantages for the fabrication of wearable energy storage devices.We expect that this Account will stimulate further efforts toward fundamental research on interface engineering in metal oxide sheet assembly and facilitate wide applications of their designed assemblies in future new-concept energy conversion devices and beyond. In the foreseeable future, we believe that there will be a big explosion in the application of transition metal oxide sheets in flexible electronics.

Nacre Is a Liquid-Crystal Thermometer of the Oceans

Nacre, or mother of pearl, is a biomaterial with a layered structure. In a recent geological study, researchers found that the width of the nacre layers depends on the formation temperature, which is determined by the ocean water temperature. A linear dependence of layer width with respect to temperature is understandable within the transient liquid-crystalline nature of incipient nacre. Thus, developing nacre is a liquid-crystal thermometer recording its formation temperature. A more complete understanding of nacre formation is of interest not only for biology and geology, in terms of biomineralization and paleoclimatology, but also for materials science: for reproducing nacre or fabricating synthetic analogues and also potentially for developing new classes of layered materials with layer spacings tunable by pH and temperature.

Lightweight Ultra-High-Barrier Liners for Helium and Hydrogen

Upcoming efficient air-borne wind energy concepts and communication technologies applying lighter-than-air platforms require high-performance barrier coatings, which concomitantly and nonselectively block permeation not only of helium but also of ozone and water vapor. Similarly, with the emergence of green hydrogen economy, lightweight barrier materials for storage and transport of this highly diffusive gas are very much sought-after, particularly in aviation technology. Here the fabrication of ultraperformance nanocomposite barrier liners by spray coating lamellar liquid crystalline dispersions of high aspect ratio (∼20 000) silicate nanosheets mixed with poly(vinyl alcohol) on a PET substrate foil is presented. Lightweight nanocomposite liners with 50 wt % filler content are obtained showing helium and hydrogen permeabilities as low as 0.8 and 0.6 cm³ μm m^-2 day^-1 atm^-1, respectively. This exhibits an improvement up to a factor of 4 × 10³ as compared to high-barrier polymers such as ethylene vinyl alcohol copolymers. Furthermore, ozone resistance, illustrated by oxygen permeability measurements at elevated relative humidity (75% r.h.), and water vapor resistance are demonstrated. Moreover, the technically benign processing by spray coating will render this barrier technology easily transferable to real lighter-than-air technologies or irregular- and concave-shaped hydrogen tanks.

Evaporation-Induced Vertical Alignment Enabling Directional Ion Transport in a 2D-Nanosheet-Based Battery Electrode

2D nanosheets have been widely explored as electrode materials owing to their extraordinarily high electrochemical activity and fast solid-state diffusion. However, the scalable electrode fabrication based on this type of material usually suffers from severe performance losses due to restricted ion-transport kinetics in a large thickness. Here, a novel strategy based on evaporation-induced assembly to enable directional ion transport via forming vertically aligned nanosheets is reported. The orientational ordering is achieved by a rapid evaporation of mixed solvents during the electrode fabrication process. Compared with conventional drop-cast electrodes, which exhibit a random arrangement of the nanosheets and obvious decrease of rate performance with increasing thickness, the electrode based on the vertically aligned nanosheets is able to retain the original high rate capability even at high mass loadings and electrode thickness. Combined electrochemical and structural characterization reveals the electrode composed of orientation-controlled nanosheets to possess lower charge-transfer resistances, leading to more complete phase transformation in the active material.

Magnetic field induced uniaxial alignment of the lyotropic liquid-crystalline PMMA-grafted Fe3O4 nanoplates with controllable interparticle interaction

Magnetite (Fe₃O₄) nanoplates with a hexagonal platelet shape were synthesized by two steps: hydrothermal synthesis of iron(iii) oxide (α-Fe₂O₃) nanoplates followed by wet chemical reduction of the α-Fe₂O₃ nanoplates. Then, poly(methyl methacrylate) (PMMA) chains were grafted onto the surface of the hexagonal Fe₃O₄ nanoplates (F) via surface-initiated atom transfer radical polymerization (SI-ATRP), which ensures dispersion stability in organic solvents and ionic liquids. After mixing with 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ([Emim⁺][NTf₂ ^-]), a representative ionic liquid, the resulting PMMA-modified F were found to show good lyotropic liquid-crystalline (LC) behaviour in [Emim⁺][NTf₂ ^-] and to exhibit a fast response to the application of an external magnetic field. Ultrasmall-angle synchrotron X-ray scattering (USAXS) measurements verified that the PMMA chain length, the weight ratio of the ionic liquid and the external magnetic field could significantly influence the interparticle distance (I _D) of the PMMA-modified F in [Emim⁺][NTf₂ ^-]. In particular, the lyotropic LC phase could be assigned as a nematic phase with a columnar alignment. In addition, the PMMA-modified F maintained a uniaxially aligned nematic columnar structure along the magnetic field direction. Our study also determined the mechanism for the special alignment of the PMMA-modified F under an external magnetic field by analysing the growth axis, the easy magnetic axes, and the interparticle distance of F. The results suggested that the special alignment of the PMMA-modified F was affected by the interparticle interaction caused by the PMMA long chains on F under the magnetic field. Furthermore, the present study revealed that PMMA-modified F exhibited a new magnetic field responsive behaviour that led not only to the formation of a uniaxial alignment structure but also to control of I _D with the help of the PMMA soft corona under the application of a magnetic field. These features could prove to be a promising advance towards novel applications of magnetic nanoparticles (NPs), such as functional magnetic fluids, rewritable magnetic switching devices, and smart magneto-electrochemical nanosensors.

Mesoscopic Architectures Made of Electrically Charged Binary Colloidal Nanosheets in Aqueous System

Inorganic layered materials can be converted to colloidal liquid crystals through exfoliation into inorganic nanosheets, and binary nanosheet colloids exhibit rich phase behavior characterized by multiphase coexistence. In particular, niobate-clay binary nanosheet colloids are characterized by phase separation at a mesoscopic (∼several tens of micrometers) scale whereas they are apparently homogeneous at a macroscopic scale. Although the mesoscopic structure of the niobate-clay binary colloid is advantageous to realize unusual photochemical functions, the structure itself has not been clearly demonstrated in real space. The present study investigated the structure of niobate-clay binary nanosheet colloids in detail. Four clay nanosheets (hectorite, saponite, fluorohectorite, and tetrasilisic mica) with different lateral sizes were compared. Small-angle X-ray scattering (SAXS) indicated lamellar ordering of niobate nanosheets in the binary colloid. The basal spacing of the lamellar phase was reduced by increasing the concentration of clay nanosheets, indicating the compression of the liquid crystalline niobate phase by the isotropic clay phase. Scattering and fluorescence microscope observations using confocal laser scanning microscopy (CLSM) demonstrated the phase separation of niobate and clay nanosheets in real space. Niobate nanosheets assembled into domains of several tens of micrometers whereas clay nanosheets were located in voids between the niobate domains. The results clearly confirmed the spatial separation of two nanosheets and the phase separation at a mesoscopic scale. Distribution of clay nanosheets is dependent on the employed clay nanosheets; the nanosheets with large lateral length are more localized or assembled. This is in harmony with larger basal spacings of niobate lamellar phase for large clay particles. Although three-dimensional compression of the niobate phase by the coexisting clay phase was observed at low clay concentrations, the basal spacing of niobate phase was almost constant irrespective of niobate concentrations at high clay concentrations, which was ascribed to competition of compression by clay phase and restoring of the niobate phase.

Hierarchically Ordered α-Zirconium Phosphate Platelets in Aqueous Phase with Empty Liquid

Platelets of α-zirconium phosphate (α-ZrP) obtained from the reflux method in H₃PO₄ are successfully exfoliated into water via the intercalation of alkanol amines. With volume fractions greater than 0.02 they are stacked into tactoids of few layers with a repeat distance in the order of 10 nm. The tactoids align into nematic liquid crystalline phases with irregularly wide interstices of empty liquid. Colloidal processing involves the freeze-drying of such anisotropic fluids and the dispersion of the restacked tacoids into aqueous dispersions of colloidal polymer particles of largely varying size which occupy the otherwise empty liquid between the α-ZrP tactoids and induce piling of the tactoids into columns. Real-time SAXS on drying films and TEM of the obtained coatings demonstrate that the stacked α-ZrP platelets and the polymer particles comprising liquid dry separately without polymer intercalation, while the morphology of the obtained composites can be tuned primarily by the size of the polymer colloids. Concomitant α-ZrP hydrolysis in the exfoliation step is scrutinized as a function of amine basicity and temperature. The role of zirconium based hydrolysis products in the hierarchical α-ZrP assembly is indirectly though consistently confirmed by opposing impacts of ultra-filtration and added oxoanions on the platelets’ spacing, smoothness and aggregation. HAADF-TEM imaging of scattered, singular platelets and XRD peak analysis of the pristine solid shed light on the α-ZrP synthesis. Coexisting flakes and lacunae, both similar in size to the intra-layer crystal domains, suggest the stitching of proto-α-ZrP flakes into extended layers in accordance with our observations on the aging behaviour of α-ZrP dispersions as well as with literature data on related systems.

Graphene Oxide Liquid Crystal Domains: Quantification and Role in Tailoring Viscoelastic Behavior

Graphene oxide liquid crystals (GOLCs) were exfoliated in a wide variety of solvents (water, ethylene glycol (EG), N-methyl-2-pyrrolidone (NMP), and dimethylformamide (DMF)) by high-speed shearing of graphite oxide. Quantitative polarized light imaging of the equilibrium nematic phases of the lyotropic GOLCs gives insights into the extent of aggregation and quantifiable textural features such as domain size, d. Large nematic domains >100 μm with a high overall degree of order were obtained in water and ethylene glycol, in contrast to ∼5-50 μm domains in NMP and DMF at comparable volume fractions. Comprehensive rheological studies of these GOLCs indicate that larger domains correlate with higher viscosity and higher elasticity, and scaling analysis shows a power-law dependence of the Ericksen number (Er) with domain size (Er ∝ d^3.09). The improved understanding of the relationship between the microstructure and flow properties of GOLCs leads us to an approach of mixed solvent-based GOLCs as a means to tune viscoelastic properties. We demonstrate this approach for the formation of shear-aligned GOLC films for advanced flexible electronic applications such as all-carbon conductive films and thermal heaters.

Electric-Alignment Immobilization of Liquid Crystalline Colloidal Nanosheets with the Aid of a Natural Organic Polymer

Inorganic nanosheets obtained by exfoliation of a layered crystal in water form colloidal liquid crystals, and their alignment can be controlled by an electric field. In order to realize the immobilization of the electrically aligned niobate nanosheets without external forces, an aqueous gelator, agar, is introduced to the niobate nanosheet system to utilize the thermosensitive sol-gel transition property of agar. Alignment of nanosheets in a niobate-agar system is performed by applying an electric field above the sol-gel transition temperature, and then, the sample is cooled down, followed by cooling below the transition temperature with the electric field turned off. The aligned structure is kept for more than 24 h after the removal of the electric field. The concentration of agar is a key parameter for both the orientation of nanosheets and the retention of the orientation.

Microscope Observation of Morphology of Colloidally Dispersed Niobate Nanosheets Combined with Optical Trapping

Although inorganic nanosheets prepared by exfoliation (delamination) of layered crystals have attracted great attention as 2D nanoparticles, in situ real space observations of exfoliated nanosheets in the colloidally dispersed state have not been conducted. In the present study, colloidally dispersed inorganic nanosheets prepared by exfoliation of layered niobate are directly observed with bright-field optical microscopy, which detects large nanosheets with lateral length larger than several micrometers. The observed nanosheets are not strictly flat but rounded, undulated, or folded in many cases. Optical trapping of nanosheets by laser radiation pressure has clarified their uneven cross-sectional shapes. Their morphology is retained under the relation between Brownian motion and optical trapping.

Directing Liquid Crystalline Self-Organization of Rodlike Particles through Tunable Attractive Single Tips

Dispersions of rodlike colloidal particles exhibit a plethora of liquid crystalline states, including nematic, smectic A, smectic B, and columnar phases. This phase behavior can be explained by presuming the predominance of hard-core volume exclusion between the particles. We show here how the self-organization of rodlike colloids can be controlled by introducing a weak and highly localized directional attractive interaction between one of the ends of the particles. This has been performed by functionalizing the tips of filamentous viruses by means of regioselectively grafting fluorescent dyes onto them, resulting in a hydrophobic patch whose attraction can be tuned by varying the number of bound dye molecules. We show, in agreement with our computer simulations, that increasing the single tip attraction stabilizes the smectic phase at the expense of the nematic phase, leaving all other liquid crystalline phases invariant. For a sufficiently strong tip attraction, the nematic state may be suppressed completely to get a direct isotropic liquid-to-smectic phase transition. Our findings provide insights into the rational design of building blocks for functional structures formed at low densities.

Tracking Molecular Diffusion in One-Dimensional Photonic Crystals

The intuitive use, inexpensive fabrication, and easy readout of colorimetric sensors, including photonic crystal architectures and Fabry-Pérot interference sensors, have made these devices a successful commercial case, and yet, understanding how the diffusion of analytes occurs throughout the structure is a key ingredient for designing the response of these platforms on demand. Herein, the diffusion of amines in a periodic multilayer system composed of two-dimensional nanosheets and dielectric nanoparticles is tracked by a combination of spectroscopic measurements and theoretical modelling. It is demonstrated that diffusion is controlled by the molecular size, with larger molecules showing larger layer swelling and slower diffusion times, which translates into important sensor characteristics such as signal change and saturation time. Since the approach visualizes the analyte impregnation process in a time- and spatially resolved fashion, it directly relates the macroscopic color readout into microscopic processes occurring at the molecular level, thus opening the door to rational sensor design.