High-performance particulate matter including nanoscale particle removal by a self-powered air filter

Two-Dimensional Piezoelectric Nanofibrous Webs by Self-Polarized Assembly for High-Performance PM0.3 Filtration

Particulate matter (PM) pollution has posed a serious threat to public health, especially the global spread of infectious diseases. Most existing air filtration materials are still subjected to a compromise between removal efficiency and air permeability on account of their stacking bulk structures. Here, we proposed a self-polarized assembly technique to create two-dimensional piezoelectric nanofibrous webs (PNWs) directly from polymer solutions. The strategy involves droplets deforming into ultrathin liquid films by inertial flow, liquid films evolving into web-like architectures by instantaneous phase inversion, and enhanced dipole alignment by cluster electrostatics. The assembled continuous webs exhibit integrated structural superiorities of nanoscale diameters (∼20 nm) of the internal fibers and through pores (∼100 nm). Combined with the wind-driven electrostatic property derived from the enhanced piezoelectricity, the PNW filter shows high efficiency (99.48%) and low air resistance (34 Pa) against PM0.3 as well as high transparency (84%), superlight weight (0.7 g m-2), and long-term stable service life. This creation of such versatile nanomaterials may offer insight into the design and upgrading of high-performance filters.

Ionic Polyimine-Based Composite Membrane with Inductive and Complexation Synergistic Effects for Sensitive and On-Site Fluorescent Detection of Volatile Iodine

Along with the development of nuclear power, concerns about radioactive emissions and the potential for nuclear leakage have been widely raised, particularly of harmful iodine isotopes. However, as a significant component of nuclear air waste, the enrichment and detection of air-dispersed gaseous iodine remain a challenge. In this work, it is focused on developing an attraction-immobilization-detection strategy-based fluorescence method for the on-site detection of volatile iodine, by employing a photoluminescent ionic polyimine network-polyvinylpyrrolidone (IPIN-PVP) composite membrane. This strategy synergizes ion-induced dipole interactions from IPIN and complexation effects from PVP, allowing effective iodine enrichment and immobilization. As a result, the optimized IPIN-PVP membrane exhibits rapid response times of 5 s and a low detection limit of 4.087 × 10-8 m for gaseous iodine. It also introduces a portable handheld detection device that utilizes the composite membrane, offering a practical solution for real-time on-site detection of volatile iodine. This innovation enhances nuclear safety measures and disaster management by providing rapid and reliable iodine detection capabilities.

Cellulose Nanofiber-Based Triboelectric Nanogenerators for Efficient Air Filtration in Harsh Environments

Advanced portable healthcare devices with high efficiencies, small pressure drops, and high-temperature resistance are urgently desired in harsh environments with high temperatures, high humidities, and high levels of atmospheric pollution. Triboelectric nanogenerators (TENGs), which serve as energy converters in a revolutionary self-powered sensor device, present a sustainable solution for meeting these requirements. In this work, we developed a porous negative triboelectric material by synthesizing ZIF-8 on the surface of a cellulose/graphene oxide aerogel, grafting it with trimethoxy(1H,1H,2H,2H-heptadecafluorodecyl)silane, and adding a negative corona treatment, and it was combined with a positive triboelectric material to create a cellulose nanofiber-based TENG self-powered filter. The devices achieved a balance between a small pressure drop (53 Pa) and high filtration efficiency (98.97%, 99.65%, and 99.93% for PM0.3, PM0.5, and PM1, respectively), demonstrating robust filtration properties at high temperatures and high humidities. Our work provides a new approach for developing self-powered wearable healthcare devices with excellent air filtration properties.

A High-Voltage-Specialized Direct-Current Triboelectric Nanogenerator for Air Purification

Human health and the environment face significant challenges of air pollution, which is predominantly caused by PM2.5 or PM10 particles. Existing control methods often require elevated energy consumption or bulky high-voltage electrical equipment. To overcome these limitations, a self-powered, convenient, and compact direct current high-voltage triboelectric nanogenerator based on triboelectrification and electrostatic breakdown effects is proposed. By optimizing the structure-design of the direct current triboelectric nanogenerator and corresponding output voltage, it can easily achieve an output voltage of over 3 kV with a high charge density of 320 µC m-2 . A power management circuit is designed to overcome the influence of third domain self-breakdown, optimize 92.5% amplitude of voltage shake, and raise 5% charge utilization ratio. With a device size as tiny as 2.25 cm3 , it can continuously drive carbon nanowires to generate negative ions that settle dust within 300 s. This compact, simple, efficient, and safe high-voltage direct current triboelectric nanogenerator represents a promising sustainable solution. It offers efficient dust mitigation, fostering cleaner environments, and enhancing overall health.

Sunlight-Driven Self-Cleaning Ultrafine Particulate Matter Filter with Antibacterial Activity

Air pollution by particulate matter (PM) and airborne pathogens causes severe health problems in the human body. Presently, popular disposable air filters yield huge waste and have a fatal impact on the environment. Postuse cleaning of air filters also leads to secondary air and water pollution. Here, we report a sunlight-driven self-cleaning PM filter by coupling a full-solar-spectrum-active photocatalyst comprising up-conversion nanoparticles (UCNPs) decorated with semiconductor iron(III) oxide (UCNP@α-Fe2O3) shells stabilized upon graphene functionalized borosilicate fibrous membrane (rGO-BF). While rGO-BF ensures high PM adsorption, UCNP@α-Fe2O3 (NP) enables self-photodegradation of adsorbed PM under abundant sunlight and subsequent membrane regeneration, while preventing secondary air or water pollution. Rational surface chemistry and optimal microstructure enable our filters to remove >99% of PM2.5 under deplorable air-quality conditions. Moreover, our filter shows excellent antibacterial activity toward E. coli and S. aureus, demonstrating its potential for practical utilization in face masks, air filtering devices, and protective medical wear. This work successfully suggests an intriguing design platform for self-sustainable zero-waste air filter membranes.

Ultrathin, ultralight dual-scale fibrous networks with high-infrared transmittance for high-performance, comfortable and sustainable PM0.3 filter

Highly permeable particulate matter (PM) can carry various bacteria, viruses and toxics and pose a serious threat to public health. Nevertheless, current respirators typically sacrifice their thickness and base weight for high-performance filtration, which inevitably causes wearing discomfort and significant consumption of raw materials. Here, we show a facile yet massive splitting eletrospinning strategy to prepare an ultrathin, ultralight and radiative cooling dual-scale fiber membrane with about 80% infrared transmittance for high-protective, comfortable and sustainable air filter. By tailoring antibacterial surfactant-triggered splitting of charged jets, the dual-scale fibrous filter consisting of continuous nanofibers (44 ± 12 nm) and submicron-fibers (159 ± 32 nm) is formed. It presents ultralow thickness (1.49 μm) and base weight (0.57 g m-2) but superior protective performances (about 99.95% PM0.3 removal, durable antibacterial ability) and wearing comfort of low air resistance, high heat dissipation and moisture permeability. Moreover, the ultralight filter can save over 97% polymers than commercial N95 respirator, enabling itself to be sustainable and economical. This work paves the way for designing advanced and sustainable protective materials.

Wearable fabric-based ZnO nanogenerator for biomechanical and biothermal monitoring

Wearable devices that can mechanically conform to human skin are a necessity for reliable monitoring and decoding of biomechanical activities through skin. Most inorganic piezoelectrics, however, lack deformability and damage tolerance, impeding stable motion monitoring. Here, we present an air-permeable fabric-based ZnO nanogenerator with mechanical adaptivity to diverse deformations for wearable piezoelectric sensors, collecting biomechanical health data. We fabricate ZnO nanorods incorporated throughout the entire nylon fabric, with a strategically positioned neutral mechanical plane, for bending-sensitive electronics (2.59 μA mm). Its hierarchically interlocked geometry also permits sensitive tactile sensing (0.15 nA kPa-1). Various physiological information about activities, including pulse beating, breathing, saliva swallowing, and coughing, is attained using skin-mounted sensors. Further, the pyroelectric sensing capability of a mask-attached device is demonstrated by identifying specific respiratory patterns. Our wearable healthcare sensors hold great promise for real-time monitoring of health-related vital signs, informing individuals' health status without disrupting their daily lives.

Boost of Gas Adsorption Kinetics of Covalent Organic Frameworks via Ionic Liquid Solution Process

Adsorption, storage, and conversion of gases (e.g., carbon dioxide, hydrogen, and iodine) are the three critical topics in the field of clean energy and environmental mediation. Exploring new methods to prepare high-performance materials to improve gas adsorption is one of the most concerning topics in recent years. In this work, an ionic liquid solution process (ILSP), which can greatly improve the adsorption kinetic performance of covalent organic framework (COF) materials for gaseous iodine, is explored. Anionic COF TpPaSO3 H is modified by amino-triazolium cation through the ILSP method, which successfully makes the iodine adsorption kinetic performance (K80% rate) of ionic liquid (IL) modified COF AC4 tirmTpPaSO3 quintuple compared with the original COF. A series of experimental characterization and theoretical calculation results show that the improvement of adsorption kinetics is benefited from the increased weak interaction between the COF and iodine, due to the local charge separation of the COF skeleton caused by the substitution of protons by the bulky cations of ILs. This ILSP strategy has competitive help for COF materials in the field of gas adsorption, separation, or conversion, and is expected to expand and improve the application of COF materials in energy and environmental science.

Nanostructured Bioaerogels as a Potential Solution for Particulate Matter Pollution

Particulate matter (PM) pollution is a significant environmental and public health issue globally. Exposure to high levels of PM, especially fine particles, can have severe health consequences. These particles can come from a variety of sources, including natural events like dust storms and wildfires, as well as human activities such as industrial processes and transportation. Although an extensive development in air filtration techniques has been made in the past few years, fine particulate matter still poses a serios and dangerous threat to human health and to our environment. Conventional air filters are fabricated from non-biodegradable and non-ecofriendly materials which can cause further environmental pollution as a result of their excessive use. Nanostructured biopolymer aerogels have shown great promise in the field of particulate matter removal. Their unique properties, renewable nature, and potential for customization make them attractive materials for air pollution control. In the present review, we discuss the meaning, properties, and advantages of nanostructured aerogels and their potential in particulate matter removal. Particulate matter pollution, types and sources of particulate matter, health effect, environmental effect, and the challenges facing scientists in particulate matter removal are also discussed in the present review. Finally, we present the most recent advances in using nanostructured bioaerogels in the removal of different types of particulate matter and discuss the challenges that we face in these applications.

Bioelectret poly(lactic acid) membranes with simultaneously enhanced physical interception and electrostatic adsorption of airborne PM0.3

Traditional polymeric fibrous membranes have been extensively used to reduce the health risks caused by airborne particulate matter (PM), leading to the dramatically increasing pollution of plastics and microplastics. Although great efforts have been made to develop poly(lactic acid) (PLA)-based membrane filters, they are frequently dwarfed by their relatively poor electret properties and electrostatic adsorptive mechanisms. To resolve this dilemma, a bioelectret approach was proposed in this work, strategically involving the bioinspired adhesion of dielectric hydroxyapatite nanowhiskers as a biodegradable electret to promote the polarization properties of PLA microfibrous membranes. In addition to significant improvements in tensile properties, the incorporation of hydroxyapatite bioelectret (HABE) enabled remarkable increase in the removal efficiencies of ultrafine PM_0.3 in a high-voltage electrostatic field (10 and 25 kV). This was exemplified by the largely increased filtering performance (69.75%, 23.1 Pa) for PLA membranes loaded with 10 wt% HABE at the normal airflow rate (32 L/min) compared to the pristine PLA counterpart (32.89%, 7.2 Pa). Although the filtration efficiency of PM_0.3 for the counterpart dramatically decreased to 21.6% at 85 L/min, the increment was maintained at nearly 196% for the bioelectret PLA, while an ultralow pressure drop (74.5 Pa) and high humidity resistance (RH 80%) were achieved. The unusual property combination were ascribed to the HABE-enabled realization of multiple filtration mechanisms, including the simultaneous enhancement of physical interception and electrostatic adsorption. The significant filtration applications, unattainable with conventional electret membranes, demonstrate the bioelectret PLA as a promising biodegradable platform that allows high filtration properties and humidity resistance.

A theoretical study on the filtration efficiency and dust holding performance of pleated air filters

Filter media composed of electrostatically charged nonwovens is the key device in an air purifier. Pleated filters are constructed from a cardboard frame with lattice faces containing a filter media reinforce by an expanded support grid, which have more surface area for trapping contaminants and capture airborne contaminants more effectively than non-pleated air filters. The aim of this work is to investigate the dominant factors on the filtration efficiency and dust holding performance of pleated filter by using a modified numerical model. It is found that geometric parameters of pleated filter play important roles to efficiency of the air purifier based on particle loading and filtration efficiency. The stable structural parameters include bending angle of pleated filter material in the range of 0∼60° and the ratio of bending portion less than 0.5. Lower filling degree and shorter length of pleated filter unit exhibit similar stability of efficiency, indicating that the change of structural parameters has little effects on the filtration performance. The knowledge obtained in this work provides concrete reference for the design of high-performance air-cleaner element.

Low-melting multicharge ionic liquids with [Ln(NO3)5]2- (Ln = Ho-Lu): structural, electrostatic, thermochemical, and fluorescence properties

A series of green and safe heavy-rare-earth ionic liquids were obtained using a straightforward method. The stable structures of these ionic liquids, characterized by high-coordinating anions, were confirmed by nuclear magnetic resonance (NMR) spectroscopy, infrared (IR) spectroscopy, and single crystal X-ray diffraction (XRD). These ionic liquids exhibited wide liquid phase intervals and excellent thermal stability. The bidentate nitrato ligands occupied a sufficient number of coordination sites on the lanthanide ions, resulting in the formation of water-free 10-coordination structures. To explain the anomalous melting points observed in these multi-charged ionic liquids, a combination of experimental data and theoretical studies was employed to investigate the relationship between the electrostatic properties and the melting point. The electrostatic potential density per unit ion surface and volume were proposed and utilized for melting point prediction, demonstrating good linearity. Furthermore, the coordinating spheres of the lanthanide ions in these ionic liquids were devoid of luminescence quenchers such as O-H and N-H groups. Notably, the ionic liquids containing Ho³⁺, Er³⁺, and Tm³⁺ exhibited long lifetime near-infrared (NIR) and blue emissions, respectively. The UV-vis-NIR spectra revealed numerous electronic transitions of the lanthanide ions, which were attributed to their unique optical properties.

Through-hole composite membrane with an ultrathin oxide shell for highly robust and transparent air filters

Exploring pore structures that are optically transparent and have high filtration efficiency for ultrafine dust is very important for realizing passive window filters for indoor air purification. Herein, a polyester track-etched (PETE) membrane with vertically perforated micropores is investigated as a cost-effective candidate for transparent window filters. The pore size, which governs transparency and filtration efficiency, can be precisely tuned by conformally depositing an ultrathin oxide layer on the PETE membrane via atomic layer deposition. The maximum visible light transmittance (∼81.2 %) was achieved with an alumina layer of approximately 55 nm, and the resulting composite membrane exhibited competitive filtration efficiency compared to commercial products. The chemically inert alumina layer also increased resistance to various external stimuli and enabled simple cleaning of the contaminated membrane surface with a solvent. The membrane installed on an insect screen effectively maintained its filtration performance (∼85 % for PM_2.5) even after 10 reuse cycles under extremely harsh conditions (PM_2.5 concentration: ∼5000 μg cm^-3). The proposed through-hole composite membrane can expand the choice of aesthetic window filters to situations that require high outside visibility and daylighting.

Highly efficient construction of sustainable bacterial cellulose aerogels with boosting PM filter efficiency by tuning functional group

Air pollution has become a major public health concern, attracting considerable attention from researchers working on environmentally friendly and sustainable materials. In this work, bacterial cellulose (BC) derived aerogels were fabricated by the directional ice-templated method and used as filters to remove PM particles. We modified the surface functional groups of BC aerogel with reactive silane precursors, and investigated the interfacial and structural properties of those aerogels. The results show that BC-derived aerogels have excellent compressive elasticity, and their directional growth orientation inside the structure significantly reduced pressure drop. Moreover, the BC-derived filters exhibit an exceptional quantitative removal effect on fine particulate matter, which, in the presence of high concentrations of fine particulate matter, they can achieve a high-efficiency removal standard of 95 %. Meanwhile, the BC-derived aerogels showed superior biodegradation performance in the soil burial test. These results paved the way for BC-derived aerogels development as a great sustainable alternative to treat air pollution.

Antibacterial, antiviral, and biodegradable collagen network mask for effective particulate removal and wireless breath monitoring

Functional face masks that can effectively remove particulate matter and pathogens are critical to addressing the urgent health needs arising from industrial air pollution and the COVID-19 pandemic. However, most commercial masks are manufactured by tedious and complicated network-forming procedures (e.g., meltblowing and electrospinning). In addition, the materials used (e.g., polypropylene) have significant limitations such as a lack of pathogen inactivation and degradability, which can cause secondary infection and serious environmental concerns if discarded. Here, we present a facile and straightforward method for creating biodegradable and self-disinfecting masks based on collagen fiber networks. These masks not only provide superior protection against a wide range of hazardous substances in polluted air, but also address environmental concerns associated with waste disposal. Importantly, collagen fiber networks with naturally existing hierarchical microporous structures can be easily modified by tannic acid to improve its mechanical characteristics and enable the in situ production of silver nanoparticles. The resulting masks exhibit excellent antibacterial (>99.99%, 15 min) and antiviral (>99.999%, 15 min) capabilities, as well as high PM_2.5 removal efficiency (>99.9%, 30 s). We further demonstrate the integration of the mask into a wireless platform for respiratory monitoring. Therefore, the smart mask has enormous promise for combating air pollution and contagious viruses, managing personal health, and alleviating waste issues caused by commercial masks.

Real-time monitoring of mercury(II) in water and food samples using a quinoline-based ionic probe

Herein, a novel ionic fluorescent probe for mercury(II) detection is presented consisting of a functional quinoline-based IL. Interestingly, the probe displayed high sensitivity (0.8 nM) and selectivity through the regulation function of electrostatic attraction, where its performance was significantly superior to that of quinoline probes without negative charge. Furthermore, the probe was found to exhibit two different fluorescent signals and colorimetric signals in the presence of different concentrations of mercury(II), which was consistent with the reaction mechanisms of the generation of large conjugated systems and the formation of anion-mercury(II) complexes. Moreover, this probe could be further loaded on a simple filter paper to serve as a visual paper sensor due to its adequate response time of less than 5 s. This regulation function strategy of electrostatic attraction has excellent potential for use in the precise detection of targeted analytes in real complex samples with improved accuracy and selectivity.

Bioinspired artificial spider silk photocatalyst for the high-efficiency capture and inactivation of bacteria aerosols

Bioaerosol can cause the spread of disease, and therefore, capture and inactivation of bioaerosols is desirable. However, filtration systems can easily become blocked, and are often unable to inactivate the bioaerosol once it is captured. Herein, we reported a bioinspired artificial spider silk (ASS) photocatalyst, consisting of a periodic spindle structure of TiO2 on nylon fiber that can efficiently capture and concentrate airborne bacteria, followed by photocatalytic inactivation in situ, without a power-supply exhaust system. The ASS photocatalyst exhibits a higher capture capacity than the nylon fiber substrate and a photocatalytic inactivation efficiency of 99.99% obtained under 4 h irradiation. We found that the capture capacity of the ASS photocatalyst can be mainly attributed to the synergistic effects of hydrophilicity, Laplace pressure differences caused by the size of the spindle knots and surface energy gradients induced by surface roughness. The bacteria captured by the ASS photocatalyst are inactivated by photocatalysis within droplets or at the air/photocatalyst interfaces. This strategy paves the way for constructing materials for bioaerosol purification.

Solvent-Responsive Reversible and Controllable Conversion between a Polyimine Membrane and an Organic Molecule Cage

Adaptive bionic self-correcting behavior offers an attractive property for chemical systems. Here, based on the dynamic feature of imine formation, we propose a solvent-responsive strategy for smart switching between an amorphous ionic polyimine membrane and a crystalline organic molecule cage without the addition of other building blocks. To adapt to solvent environmental constraints, the aldehyde and amine components undergo self-correction to form a polymer network or a molecular cage. Studies have shown that the amorphous film can be switched in acetonitrile to generate a discrete cage with bright birefringence under polarized light. Conversely, the membrane from the cage crystal conversion can be regained in ethanol. Such a membrane-cage interconversion can be cycled continuously at least 5 times by switching the two solvents. This work builds a bridge between the polymer network and crystalline molecules and offers prospects for smart dynamic materials.

Lead Sequestration in Perovskite Photovoltaic Device Encapsulated with Water-Proof and Adhesive Poly(ionic liquid)

The inevitable usage of toxic lead impedes the commercialization of lead halide perovskite solar cells, especially considering lead ions potentially unseals from the discarded and damaged devices and consequently contaminates the environment. In this work, we proposed a poly(ionic liquid) (PIL) cohered sandwich structure (PCSS) to realize lead sequestration in perovskite solar cells by a water-proof and adhesive poly([1-(3-propionic acid)-3-vinylimidazolium] bis(trifluoromethanesulphonyl)imide (PPVI-TFSI). A transparent ambidextrous protective shield manufactured from PPVI-TFSI was achieved and applied in lead sequestration for perovskite solar cells. PCSS provides robustness and water-resistance, which improves device stability toward water erosion and extreme situations (such as acid, base, salty water, and hot water). PPVI-TFSI exhibited excellent affinity toward lead with adsorption capacity of 516 mg·g^-1, which assisted to prevent lead leakage in abandoned devices as proved in the test of wheat germination vividly. PCSS provides a promising solution for complex lead sequestration and management issues, which contribute to the commercialization of perovskite solar cells.

Long-lifetime water-washable ceramic catalyst filter for air purification

Particulate matter (PM) and volatile organic compounds (VOCs) are recognised as hazardous air pollutants threatening human health. Disposable filters are generally used for air purification despite frequent replacement and waste generation problems. However, the development of a novel regenerable and robust filter for long-term use is a huge challenge. Here, we report on a new class of facile water-washing regenerable ceramic catalyst filters (CCFs), developed to simultaneously remove PM (>95%) and VOCs (>82%) in single-pass and maximized space efficiency by coating the inner and outer filter channels with an inorganic membrane and a Cu₂O/TiO₂ photocatalyst, respectively. The CCFs reveal four-fold increase in the maximum dust loading capacity (approximately 20 g/L) in relation to conventional filters (5 g/L), and can be reused after ten regeneration capability with simple water washing retaining initial PM and VOC removal performances. Thus, the CCFs can be well-suited for indoor and outdoor air purification for 20 years, which shows a huge increase in lifetime compared to the 6-month lifespan of conventional filters. Finally, we believe that the development and implementation of CCFs for air purification can open new avenues for sustainable technology through renewability and zero-waste generation.

Self-charging electrostatic face masks leveraging triboelectrification for prolonged air filtration

Electrostatic adsorption is an important complement to the mechanical filtration for high-efficiency air filtering. However, the electrostatic charge decays with time, especially in humid conditions. In this work, a self-charging air filter is presented to capture airborne particles in an efficient and long-lasting manner without the need of external power sources. Leveraging the triboelectric effect between the electrospun poly(vinylidene fluoride) nanofiber film and nylon fabric, the self-charging air filter-based mask excited by breathing can continuously replenish electrostatic charges. As a result, its effective lifespan is up to 60 hours (including 30 hours of wearing), with a minimum filtration efficiency of 95.8% for 0.3-μm particles. The filtration efficiency and lifespan are significantly higher than those of a commercial surgical mask. Furthermore, we uncover the quantitative relation between filtration efficiency and surface electrostatic potential. This work provides an effective strategy to significantly prolong the electrostatic adsorption efficacy for high-performance air-filtering masks.

Superhydrophobic and highly moisture-resistant PVA@EC composite membrane for air purification

Electrospun fiber membranes have great potential in the field of air filtration because of their high porosity and small pore size. Conventional air filtration membranes are hydrophilic, leading to weak moisture-barrier properties, which hinders their application in high-humidity environments. In this study, eugenol was added to polyvinyl alcohol and ethyl cellulose (EC) for electrospinning and electrospraying, respectively, of superhydrophobic bilayer composite fiber membranes to efficiently filter particulate matter (PM) in air. Owing to its surface microstructure, electrosprayed EC increased the water contact angle of the PVA membrane from 142.8 to 151.1°. More importantly, the composite air-filter membrane showed a low filtration pressure drop (168.1 Pa) and exhibited high filtration efficiencies of 99.74 and 99.77% for PM1.0 and PM2.5, respectively, and their respective quality factors were 0.0351 and 0.0358 Pa-1. At the same time, the filtration performance of the air filtration membrane remained above 99% at high air humidity. This work reports composite membranes that can effectively capture PM of various sizes and thus may provide a reference for the manufacturing of green air filters for high-humidity environments.

Smart Nanostructured Materials for SARS-CoV-2 and Variants Prevention, Biosensing and Vaccination

The coronavirus disease 2019 (COVID-19) pandemic, caused by the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), has raised great concerns about human health globally. At the current stage, prevention and vaccination are still the most efficient ways to slow down the pandemic and to treat SARS-CoV-2 in various aspects. In this review, we summarize current progress and research activities in developing smart nanostructured materials for COVID-19 prevention, sensing, and vaccination. A few established concepts to prevent the spreading of SARS-CoV-2 and the variants of concerns (VOCs) are firstly reviewed, which emphasizes the importance of smart nanostructures in cutting the virus spreading chains. In the second part, we focus our discussion on the development of stimuli-responsive nanostructures for high-performance biosensing and detection of SARS-CoV-2 and VOCs. The use of nanostructures in developing effective and reliable vaccines for SARS-CoV-2 and VOCs will be introduced in the following section. In the conclusion, we summarize the current research focus on smart nanostructured materials for SARS-CoV-2 treatment. Some existing challenges are also provided, which need continuous efforts in creating smart nanostructured materials for coronavirus biosensing, treatment, and vaccination.

Constructing Janus Microsphere Membranes for Particulate Matter Filtration, Directional Water Vapor Transfer, and High-Efficiency Broad-Spectrum Sterilization

Commercial masks have significant drawbacks, including low water vapor transmission efficiency and limited ability to inhibit harmful microorganisms, whereas in this contribution, a series of Janus microsphere membranes are developed with hierarchical structures by quenching and crystallizing 12-hydroxystearic acid and halicin layer-by-layer on a polypropylene non-woven fabric, laminating them with hydrophilic cotton fibers in a one-pot process, and further demonstrate the potential of this composite system as masks. Through further optimization, excellent superhydrophobic/superhydrophilic properties (contact angle 157.1°/0°), superior filtering effects (93.54% for PM_2.5 and 98.35% for PM₁₀ ), with a low-filtration resistance (57 Pa) and a quality factor of up to 0.072 Pa^-1 are achieved, all better than that of commercial N95 masks. In addition, the membrane allows for the directional transport of water vapor from the inside out, increasing the water vapor transmission rate by more than 20% compared with the monolayer hydrophobic microsphere membrane. It also has a bactericidal capacity of over 99.9999% against Escherichia coli and is tested for robustness and stability in various extreme environments. This work may shed light on designing novel filter media with versatile functions, meanwhile, the materials can also be used in protective equipment against the new coronavirus.

High-performance multifunctional electrospun fibrous air filter for personal protection: A review

With the increasingly serious air pollution and the rampant coronavirus disease 2019 (COVID–19), preparing high–performance air filter to achieve the effective personal protection has become a research hotspot. Electrospun nanofibrous membrane has become the first choice of air filter because of its small diameter, high specific surface area and porosity. However, improving the filtration performance of the filter only cannot meet the personal needs: it should be given more functions based on high filtration performance to maximize the personal benefits, called, multifunctional, which can also be easily realized by electrospinning technology, and has attracted much attention. In this review, the filtration mechanism of high–performance electrospun air filter is innovatively summarized from the perspective of membrane. On this basis, the specific preparation process, advantages and disadvantages are analyzed in detail. Furthermore, other functions required for achieving maximum personal protection benefits are introduced specifically, and the existing high–performance electrospun air filter with multiple functions are summarized. Finally, the challenges, limitations, and development trends of manufacturing high–performance air filter with multiple functions for personal protection are presented.

Continuous air purification by aqueous interface filtration and absorption

The adverse impact of particulate air pollution on human health^1,2 has prompted the development of purification systems that filter particulates out of air^3-5. To maintain performance, the filter units must inevitably be replaced at some point, which requires maintenance, involves costs and generates solid waste^6,7. Here we show that an ion-doped conjugated polymer-coated matrix infiltrated with a selected functional liquid enables efficient, continuous and maintenance-free air purification. As the air to be purified moves through the system in the form of bubbles, the functional fluid provides interfaces for filtration and for removal of particulate matter and pollutant molecules from air. Theoretical modelling and experimental results demonstrate that the system exhibits high efficiency and robustness: its one-time air purification efficiency can reach 99.6%, and its dust-holding capacity can reach 950 g m^-2. The system is durable and resistant to fouling and corrosion, and the liquid acting as filter can be reused and adjusted to also enable removal of bacteria or odours. We anticipate that our purification approach will be useful for the development of specialist air purifiers that might prove useful in a settings such as hospitals, factories and mines.

Air pollution: A culprit of lung cancer

Air pollution is a global health problem, especially in the context of rapid economic development and the expansion of urbanization. Herein, we discuss the harmful effects of outdoor and indoor pollution on the lungs. Ambient particulate matters (PMs) from industrial and vehicle exhausts is associated with lung cancer. Workers exposed to asbestos, polycyclic aromatic hydrocarbons (PAHs), and toxic metals are also likely to develop lung cancer. Indoors, cooking fumes, second-hand smoke, and radioactive products from house decoration materials play roles in the development of lung cancer. Bacteria and viruses can also be detrimental to health and are important risk factors in lung inflammation and cancer. Specific effects of lung cancer caused by air pollution are discussed in detail, including inflammation, DNA damage, and epigenetic regulation. In addition, advanced materials for personal protection, as well as the current government policies to prevent air pollution, are summarized. This review provides a basis for future research on the relationship between lung cancer and air pollution.

Degradable, antibacterial and ultrathin filtrating electrospinning membranes of Ag-MOFs/poly(l-lactide) for air pollution control and medical protection

The widely used melt-blown polypropylene (PP) non-woven fabrics had no antibacterial functions and its large-scale use also increased the burden on the environment owing to its non-degradable property. Herein, silver (I) metal organic frameworks (Ag-2MI) were prepared with AgNO3 and 2-methylimidazole and embedded into degradable poly(l-lactide) (PLLA) to make an ultrathin filtration and antibacterial membrane by electrospinning technology with low loading of Ag-2MI. The morphology, mechanical properties, adsorption performance and antibacterial activities of the prepared films were tested and the results indicated that the addition of Ag-2MI could reduce the diameter of PLLA fibers from 910 nm to 520 nm (1.8 wt% of Ag-2MI), while the tensile strength, elongation at break of the membrane and the contact angle of the films were enhanced. Although the thickness of the prepared membranes was only about one-third of that of commercially available melt-blown cloth, they exhibited better filtering performances than the melt-blown cloth. The fiber membrane with low loading of 1.8 wt% Ag-2MI showed 99.99% inhibition rate against Escherichia coli and Staphylococcus aureus.

Polyelectrolyte aerogels with regeneration capacity for efficient removal of particulate matters

HYPOTHESIS

With the rapid development of economy and global industrialization, the problem of air pollution has become a worldwide topic. The efficient filtration of airborne particulate matters (PMs) is critical for human health and environmental sustainability.

EXPERIMENTS

Herein, self-supporting bio-based polyelectrolyte aerogels were prepared and acted as the advanced filters for efficient removal of PMs. The natural choline cation (Ch⁺) or the organic cation, 1-butyl-3-methylimidazolium (Bmim⁺), are introduced into alginate (Alg^-) to form the polyelectrolytes of ChAlg or BmimAlg due to the electrostatic interaction. By the directional freeze-drying in liquid N₂, hierarchically porous aerogels with mechanical robustness, flexibility and thermo-stability were prepared. This specific structure may permit the polluted air to pass adequately through the aerogel channels, which are conducive to intercept various PMs with different diameters.

FINDINGS

As an example, the removal efficiency of ChAlg aerogels for PM₁₀, PM_2.5 and PM_0.3 are respectively up to (99.24 ± 0.03)%, (99.22 ± 0.02)%, and (93.41 ± 0.22)% within 15 h durability test. One outstanding character lies in ensuring high removal efficiency, while achieving a good balance with the low pressure drop (10 Pa), which is driven by synergistic effect of passive trapping and electrostatic capture. Moreover, the polyelectrolyte aerogels exhibit excellent antimicrobial activity and regenerated capacity. These properties endow the aerogels of polyelectrolyte ChAlg or BmimAlg with remarkable potential as new advanced filters for masks and other personal protective equipment.

Advanced materials used in wearable health care devices and medical textiles in the battle against coronavirus (COVID-19): A review

The novel coronavirus disease (COVID-19) has generated great confusion around the world, affecting people's lives and producing a large number of deaths. The development of portable and wearable devices is of great importance in several fields such as point-of-care medical applications and environmental monitoring. Wearable devices with an ability to collect various types of physiological records are progressively becoming incorporated into everyday life of people. Physiological indicators are essential health indicators and their monitoring could efficiently enable early discovery of disease. This would also help decrease the number of extra severe health problems, in disease avoidance, and lower the overall public sector health cost. Protective clothing is nowadays a main part of textiles classified as technical or industrial textiles. Protective clothing aims to protect its wearer from the harsh environmental impacts that may result in injury or death. Providing protection for the common population has also been taken seriously considering the anticipated disaster due to virus attacks. This review highlights the properties of the materials that are used in wearable health care device and medical textiles.

Aerosol capture and coronavirus spike protein deactivation by enzyme functionalized antiviral membranes

The airborne nature of coronavirus transmission makes it critical to develop new barrier technologies that can simultaneously reduce aerosol and viral spread. Here, we report nanostructured membranes with tunable thickness and porosity for filtering coronavirus-sized aerosols, combined with antiviral enzyme functionalization that can denature spike glycoproteins of the SARS-CoV-2 virus in low-hydration environments. Thin, asymmetric membranes with subtilisin enzyme and methacrylic functionalization show more than 98.90% filtration efficiency for 100-nm unfunctionalized and protein-functionalized polystyrene latex aerosol particles. Unfunctionalized membranes provided a protection factor of 540 ± 380 for coronavirus-sized particle, above the Occupational Safety and Health Administration's standard of 10 for N95 masks. SARS-CoV-2 spike glycoprotein on the surface of coronavirus-sized particles was denatured in 30 s by subtilisin enzyme-functionalized membranes with 0.02-0.2% water content on the membrane surface.

Speaking-Induced Charge-Laden Face Masks with Durable Protectiveness and Wearing Breathability

Face masks, which serve as personal protection equipment, have become ubiquitous for combating the ongoing COVID-19. However, conventional electrostatic-based mask filters are disposable and short-term effective with high breathing resistance, causing respiratory ailments and massive consumption (129 billion monthly), intensifying global environmental pollution. In an effort to address these challenges, the introduction of a piezoelectric polymer was adopted to realize the charge-laden melt-blown via the melt-blowing method. The charge-laden melt-blown could be applied to manufacture face masks and to generate charges triggered by mechanical and acoustic energy originated from daily speaking. Through an efficient and scalable industrial melt-blown process, our charge-laden mask is capable of overcoming the inevitable electrostatic attenuation, even in a high-humidity atmosphere by long-wearing (prolonging from 4 to 72 h) and three-cycle common decontamination methods. Combined with outstanding protective properties (PM2.5 filtration efficiency >99.9%), breathability (differential pressure <17 Pa/cm2), and mechanical strength, the resultant charge-laden mask could enable the decreased replacement of masks, thereby lowering to 94.4% of output masks worldwide (∼122 billion monthly) without substituting the existing structure or assembling process.

Design and construction of a low cost air purifier for killing harmful airborne microorganisms using a combination of a strong multi-directional electric-field and an ultra violet light

In this work we have designed and developed a low cost and simple instrument to purify air in an enclosure. The device sucks up the air in the enclosed area, kills the microorganisms and let clean air flow out. A combination of an ultra violet light and an electric field are used to kill the microorganisms in air. Three electric field chambers (radial, parallel, perpendicular) are used to clean air more effectively. Stainless steel meshes were used to increase the density of the electric fields. The outer covers were made with plastic and wood. The instrument was tested against an evaporated bacterial solution (Staphylococcus aureus) by letting it flow through the instrument and measuring the bacterial concentration of the output air. The results showed the instrument is extremely effective even when tested against high bacterial concentrations. The instrument is extremely useful to clean air in closed rooms such as in hospitals, schools, etc. and prevent the spread of airborne diseases.

Ultralow-cost portable device for cesium detection via perovskite fluorescence

Public anxiety and concern from cesium pollution in oceans have been back on the agenda since tons of nuclear waste water were announced to be poured into oceans. Cesium ion can easily enter organisms and bioaccumulate in animals and plants, thus its harm is chronic to humans through food chains. Here we showed a kind of hybrid ionic liquid membrane (HILM) for detection of cesium ion in seawater through CsPbBr₃ perovskite fluorescence. With sustainability in mind, HILM was built frugally. The lowest cost of HILM is below 3 cents per piece. The HILM can detect cesium ion quickly with eye-readable fluorescence signal. Ultracheap, portable, easy-to-use on-site detection device could offer benefit for personal security and applications in environment science and ecology in the future decades.

Fabrication of a High-Performance and Reusable Planar Face Mask in Response to the COVID-19 Pandemic

The coronavirus disease 2019 (COVID-19) pandemic has caused a surge in demand for face masks, with the massive consumption of masks leading to an increase in resource-related and environmental concerns. In this work, we fabricated meltblown polypropylene (mb-PP)-based high-performance planar face masks and investigated the effects of six commonly used disinfection methods and various mask-wearing periods on the reusability of these masks. The results show that, after three cycles of treatment using hot water at 70 °C for 30 min, which is one of the most scalable, user-friendly methods for viral disinfection, the particle filtration efficiency (PFE) of the mask remained almost unchanged. After mask wearing for 24 h and subsequent disinfection using the same treatment procedures, the PFE decreased to 91.3%; the average number of bacterial and fungal colonies was assessed to be 9.2 and 51.6 colony-forming units per gram (CFU∙g^{- 1}), respectively; and coliform and pyogenic bacteria were not detected. Both the PFE and the microbial indicators are well above the standard for reusable masks after disinfection. Schlieren photography was then used to assess the capabilities of used and disinfected masks during use; it showed that the masks exhibit a high performance in suppressing the spread of breathed air.

Ti-40Al-10Nb-10Cr Porous Microfiltration Membrane with Hierarchical Pore Structure for Particulate Matter Capturing from High-Temperature Flue Gas

TiAl-based porous microfiltration membranes are expected to be the next-generation filtration materials for potential applications in high-temperature flue gas separation in corrosive environments. Unfortunately, the insufficient high-temperature oxidation resistance severely limits their industrial applications. To tackle this issue, a Ti-40Al-10Nb-10Cr porous alloy was fabricated for highly effective high-temperature flue gas purification. Benefited from microstructural changes and the formation of two new phases, the Ti-40Al-10Nb-10Cr porous alloy demonstrated favorable high-temperature anti-oxidation performance with the incorporation of Nb and Cr high-temperature alloying elements. By the separation of a simulated high-temperature flue gas, we achieved an ultra-high PM-removal efficiency (62.242% for PM<2.5 and 98.563% for PM>2.5). These features, combined with our experimental design strategy, provide a new insight into designing high-temperature TiAl-based porous materials with enhanced performance and durability.

Ionic liquids enable the preparation of a copper-loaded gel with transdermal delivery function for wound dressings

Antibacterial hydrogel dressings play an important role in wound healing and infection treatment. The majority of hydrogels are obtained through chemical cross-linking and complex synthesis or processing. Copper ions (Cu²⁺) have been involved in sterilization; however, their direct use may lead to high local concentrations and heavy metal toxic side effects. Herein, dopamine (DA) was polymerized in situ along a polyvinyl alcohol (PVA) chain and chelated copper ions (Cu²⁺) to form a mixture. Ionic liquid (IL) choline-glycolate (CGLY) was added to the mixture to form an ionic gel. CGLY promotes gel formation through intermolecular hydrogen bonds with the polymer chains and avoids the use of toxic chemical crosslinking agents. Meanwhile, CGLY can also promote the release of Cu²⁺ and generate hydrogel free radicals (˙OH) in the wound through chemodynamic therapy to kill drug-resistant bacteria. In addition, the excellent transdermal property of CGLY enables the released Cu²⁺ to stimulate cell migration and accelerate wound healing. The gel exhibits favorable biocompatibility and its use has been demonstrated in skin infection therapy of mice.

Transparent Air Filters with Active Thermal Sterilization

The worldwide proliferation of COVID-19 poses the urgent need for sterilizable and transparent air filters to inhibit virus transmission while retaining ease of communication. Here, we introduce copper nanowires to fabricate transparent and self-sterilizable air filters. Copper nanowire air filter (CNAF) allowed visible light penetration, thereby can exhibit facial expressions, helpful for better communication. CNAF effectively captured particulate matter (PM) by mechanical and electrostatic filtration mechanisms. The temperature of CNAF could be controlled by Joule-heating up to 100 °C with thermal stability. CNAF successfully inhibited the growth of E. coli because of the oligodynamic effect of copper. With heat sterilization, the antibacterial efficiency against G. anodireducens was greatly improved up to 99.3% within 10 min. CNAF showed high reusability with stable filtration efficiency and thermal antibacterial efficacy after five repeated uses. Our result suggests an alternative form of active antimicrobial air filter in preparation for the current and future pandemic situations.

Multi-layered micro/nanofibrous nonwovens for functional face mask filter

The worldwide COVID-19 pandemic has led to an attention on the usage of personal protective face masks. However, the longevity and safety of the commercial face masks are limited due to the charge dissipation of the electret meltblown nonwovens, which are dominate in the face mask filters. Herein, we design a type of multi-layer structured nonwovens using meltblowing and electrospinning technologies. The complex nonwovens involving meltblown and electrospun fibers are designed to possess multilevel fiber diameters and pore sizes. The micro/nanofibers with porous and wrinkled surface morphologies can well capture particulate matters (PMs), and the multilevel pore sizes contribute to low air resistance under high filtration efficiency. Airflow field simulation was carried out to understand the pressure distribution within the nonwovens in the filtration process. Meanwhile, by adding Ag nanoparticles (AgNPs) as additives, the nonwovens exhibit excellent antibacterial performance. The resultant nonwovens exhibit filtration efficiency of 99.1% for PM_0.3 and low pressure drop of 105 Pa under the 10.67 cm/s inlet air velocity, and antibacterial rate of > 99.99% for Escherichia coli. These performances and functions make the designed complex nonwovens a promising filter core for face masks.

ELECTRONIC SUPPLEMENTARY MATERIAL

Supplementary material (Fig. S1. The filtration efficiencies of a brand of surgical mask changes with the storage time under the condition of 100% humidity. Fig. S2. The FE-SEM images of the fibers after blocking PMs. Fig. S3. Illustration of 3D structure models of the nonwovens. Fig. S4. Diameter distribution of AgNPs. Table S1. The structure parameters and filtration performances of the PP-M fibers with and without pores and wrinkles. Table S2. Filtration performance of PP-M/PLA-M/PLA-N nonwovens and commercial face masks. Table S3. The structural parameters for the nonwovens. Table S4. The filtration efficiencies and pressure drops of the PP, PE spunbonded nonwovens, and PP-M/PLA-M/PLA-N@AgNPs nonwovens) is available in the online version of this article at 10.1007/s12274-022-4350-2.

Multifunctional filter membrane for face mask using bacterial cellulose for highly efficient particulate matter removal

ABSTRACT

Particulate matter (PM) pollution and SARS-CoV-2 (COVID-19) have brought severe threats to public health. High level of PM serves as a carrier of COVID-19 which is a global pandemic. This study fabricated filter membrane for face mask using bacterial cellulose and fingerroot extract (BC-FT) via immersion technique. The surface area, pore volume and pore size of BC were analyzed by Brunauer-Emmett-Teller. The physiochemical properties of the membrane were analyzed by scanning electron microscopy, Fourier transform infrared spectroscopy and X-ray diffractometer. The crystallinity decreased from 63.7% in pure BC to 52.4% in BC-FT filter membrane. Young's modulus increased from 1277.02 MPa in pure BC to 2251.17 MPa in BC-FT filter membrane. The filter membrane showed excellent PM 0.1 removal efficiency of 99.83% and antimicrobial activity against Staphylococcus aureus and Escherichia coli. The fabricated membrane is excellent to prevent inhalation of PM2.5 and COVID-19 respiratory droplet.

SUPPLEMENTARY INFORMATION

The online version contains supplementary material available at 10.1007/s10570-022-04641-3.

Masks for COVID-19

Sustainable solutions on fabricating and using a face mask to block the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) spread during this coronavirus pandemic of 2019 (COVID-19) are required as society is directed by the World Health Organization (WHO) toward wearing it, resulting in an increasingly huge demand with over 4 000 000 000 masks used per day globally. Herein, various new mask technologies and advanced materials are reviewed to deal with critical shortages, cross-infection, and secondary transmission risk of masks. A number of countries have used cloth masks and 3D-printed masks as substitutes, whose filtration efficiencies can be improved by using nanofibers or mixing other polymers into them. Since 2020, researchers continue to improve the performance of masks by adding various functionalities, for example using metal nanoparticles and herbal extracts to inactivate pathogens, using graphene to make masks photothermal and superhydrophobic, and using triboelectric nanogenerator (TENG) to prolong mask lifetime. The recent advances in material technology have led to the development of antimicrobial coatings, which are introduced in this review. When incorporated into masks, these advanced materials and technologies can aid in the prevention of secondary transmission of the virus.

Electronic Textiles for Wearable Point-of-Care Systems

Traditional public health systems are suffering from limited, delayed, and inefficient medical services, especially when confronted with the pandemic and the aging population. Fusing traditional textiles with diagnostic, therapeutic, and protective medical devices can unlock electronic textiles (e-textiles) as point-of-care platform technologies on the human body, continuously monitoring vital signs and implementing round-the-clock treatment protocols in close proximity to the patient. This review comprehensively summarizes the research advances on e-textiles for wearable point-of-care systems. We start with a brief introduction to emphasize the significance of e-textiles in the current healthcare system. Then, we describe textile sensors for diagnosis, textile therapeutic devices for medical treatment, and textile protective devices for prevention, by highlighting their working mechanisms, representative materials, and clinical application scenarios. Afterward, we detail e-textiles' connection technologies as the gateway for real-time data transmission and processing in the context of 5G technologies and Internet of Things. Finally, we provide new insights into the remaining challenges and future directions in the field of e-textiles. Fueled by advances in chemistry and materials science, textile-based diagnostic devices, therapeutic devices, protective medical devices, and communication units are expected to interact synergistically to construct intelligent, wearable point-of-care textile platforms, ultimately illuminating the future of healthcare system in the Internet of Things era.

Solid-Liquid Host-Guest Composites: The Marriage of Porous Solids and Functional Liquids

Composite materials can provide remarkable improvements over the individual constituents. Especially, with a liquid component introduced into a solid porous host, solid-liquid host-guest composites have recently come to the forefront with exceptional functions that promise them for a wealth of applications. Combining the unprecedented dynamic, transparent, omniphobic, self-healing, diffusive and adaptive nature of functional liquid with inherent solid host's property, solid-liquid host-guest composites can realize the ease of fabrication, long-term stability, and a broad spectrum of enhanced properties, which cannot be fully met by conventional solid-solid composites or liquid-liquid composites. This review presents the state-of-the-art progress in solid-liquid host-guest composites. Initially, the concept, classification, design strategy, as well as fabrication methods as a path forward to develop the composites are unraveled, and further it is elaborated on how the functionality of porous solid and functional liquid can be harnessed to create composites with a broad range of unique properties, especially, the optical, thermal, electric, mechanical, sorption, and separation properties. With these fascinating properties, a myriad of emerging applications such as optical devices, thermal management, electromagnetic-interference shielding, soft electronics, gas capture and release, and multiphase separations are touched upon, inspiring more frontier researches in materials science, interfacial chemistry, membrane science, engineering, and multidisciplinary. Finally, this review provides the perspective on the future directions of solid-liquid host-guest composites and assesses the challenges and opportunities ahead.

Recent Progress in the Energy Harvesting Technology-From Self-Powered Sensors to Self-Sustained IoT, and New Applications

With the fast development of energy harvesting technology, micro-nano or scale-up energy harvesters have been proposed to allow sensors or internet of things (IoT) applications with self-powered or self-sustained capabilities. Facilitation within smart homes, manipulators in industries and monitoring systems in natural settings are all moving toward intellectually adaptable and energy-saving advances by converting distributed energies across diverse situations. The updated developments of major applications powered by improved energy harvesters are highlighted in this review. To begin, we study the evolution of energy harvesting technologies from fundamentals to various materials. Secondly, self-powered sensors and self-sustained IoT applications are discussed regarding current strategies for energy harvesting and sensing. Third, subdivided classifications investigate typical and new applications for smart homes, gas sensing, human monitoring, robotics, transportation, blue energy, aircraft, and aerospace. Lastly, the prospects of smart cities in the 5G era are discussed and summarized, along with research and application directions that have emerged.

Self-Supporting Three-Dimensional Electrospun Nanofibrous Membrane for Highly Efficient Air Filtration

High-performance air filtration was the key to health protection from biological and ultrafine dust pollution. A self-supporting, three-dimensional (3D) nanofibrous membrane with curled pattern was electrospun for the filtration, of which the micro-fluffy structure displayed high-filtration efficiency and low-pressure drop. The flow field in the 3D filtration membrane was simulated to optimize the process parameters to increase the filtration performance. The qualification factor increased from 0.0274 Pa⁻¹ to 0.0309 Pa⁻¹ by 12.77% after the optimization of the electrospinning parameters. The best filtration efficiency and pressure drop were 93.6% and 89.0 Pa, separately. This work provides a new strategy to fabricate 3D structures through the construction of fiber morphology and promotes further improvement of air filtration performance of fibrous filters.

Ultralow Resistance Two-Stage Electrostatically Assisted Air Filtration by Polydopamine Coated PET Coarse Filter

Airborne particulate matters (PM) pose serious health threats to the population, and efficient filtration is needed for indoor and vehicular environments. However, there is an intrinsic conflict between filtration efficiency, air resistance, and service life. In this study, a two-stage electrostatically assisted air (EAA) filtration device is designed and the efficiency-air resistance-filter life envelope is significantly improved by a thin coating of polydopamine (PDA) on the polyethylene terephthalate (PET) coarse filter by in situ dopamine polymerization. The 8 mm thick EAA PDA-140@PET filter has a high filtration efficiency of 99.48% for 0.3 µm particles, low air resistance of 9.5 Pa at a filtration velocity of 0.4 m s^-1 , and steady performance up to 30 d. Compared with the bare PET filter, the penetration rate for 0.3 µm particles is lowered by 20×. The coated PDA is of submicron thickness, 10^-3  × the gap distance between filter fibers, so low air resistance could be maintained. The filter shows steadily high filtration efficiency and an acceptable increase of air resistance and holds nearly as many particles as its own weight in a 30 day long-term test. The working mechanism of the EAA coarse filter is investigated, and the materials design criteria are proposed.