Facile synthesis to tune size, textural properties and fiber density of dendritic fibrous nanosilica for applications in catalysis and CO2 capture

Preparation and application of KCC-1@ZIF-8 for the solid extraction of tetracycline with high adsorption capacity

In this study, three different materials were prepared: dendritic fiber-type silica (KCC-1), zeolitic imidazolate framework-8 (ZIF-8), and a new composite material called KCC-1@ZIF-8. These materials were synthesized using microemulsion, stirring, and coating methods, respectively. The properties of the materials were characterized using various techniques such as transmission electron microscopy (TEM), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), TGA and X-ray diffraction (XRD). The results showed that KCC-1@ZIF-8 exhibited a significant increase in the BET surface area and pore size compared to the individual components KCC-1 and ZIF-8. These improved properties of the composite material were beneficial for enhancing the adsorption capacity. The effects of initial concentrations, solution pH and reaction time on the adsorption capacity were investigated. The adsorption kinetics and isothermal data of ZIF-8 and KCC-1@ZIF-8 fitted well with pseudo-second-order and Langmuir isotherm models. The results of adsorption thermodynamics show that the adsorption process is spontaneous and endothermic. KCC-1@ZIF-8 exhibited a very high adsorption capacity (751.46 mg g-1) at an initial TC hydrochloride concentration of 80 mg L-1 in an aqueous solution at 301.15 K, and the value was higher than that of ZIF-8 (549.80 mg g-1) under the same conditions. KCC-1 exhibited a relatively lower capacity (37.860 mg g-1). Based on these findings, KCC-1@ZIF-8 was considered a promising adsorbent for the treatment of wastewater contaminated with TC hydrochloride. Additionally, the composite material, when combined with high-performance liquid chromatography (HPLC), could be used as a solid-phase extraction adsorbent for the adsorption of TC hydrochloride in animal foodstuff samples. The calibration curves showed a linear range of 20-500 μg L-1, and the recovery rate ranged from 85.216% to 90.717%. No one has made adsorbents with this new structure before, and KCC-1@ZIF-8 possessed excellent adsorption properties, which make it a potential candidate for environmental remediation and analytical applications involving TC hydrochloride.

Learning Adsorption Patterns on Amorphous Surfaces

The physicochemical heterogeneity found on amorphous surfaces leads to a complex interaction of adsorbate molecules with topological and undercoordinated defects, which enhance the adsorption capacity and can participate in catalytic reactions. The identification and analysis of the adsorption structure observed on amorphous surfaces require novel tools that allow the segmentation of the surfaces into complex-shaped regions that contrast with the periodic patterns found on crystalline surfaces. We propose a Random Forest (RF) classifier that segments the surface into regions that can then be further analyzed and classified to reveal the dynamics of the interaction with the adsorbate. The RF segmentation is applied to the surface density map of the adsorbed molecules and employs multiple features (intensity, gradient, and the eigenvalues of the Hessian matrix) which are nonlocal and allow a better identification of the adsorption structures. The segmentation depends on a set of parameters that specify the training set and can be tailored to serve the specific purpose of the segmentation. Here, we consider an example in which we aim to separate highly heterogeneous regions from weakly heterogeneous regions. We demonstrate that the RF segmentation is able to separate the surface into a fully connected weakly heterogeneous region (whose behavior is somehow similar to crystalline surfaces and has an exponential distribution of the residence time) and a very heterogeneous region characterized by a complex residence-time distribution, which is generated by the undercoordinated defects and is responsible for the peculiar characteristics of the amorphous surface.

Designed Nanoarchitectures of a BiOBr/BiOI Nanosheet Heterojunction Anchored on Dendritic Fibrous Nanosilica as Visible-Light Responsive Photocatalysts

Heterojunctions, particularly those involving BiOBr/BiOI, have attracted significant attention in the field of photocatalysis due to their remarkable properties. In this study, a unique architecture of BiOBr/BiOI was designed to facilitate the rapid transfer of electrons and holes, effectively mitigating the recombination of electron-hole pairs. Accordingly, the BiOBr/BiOI nanosheet heterojunction was anchored on dendritic fibrous nanosilica (DFNS) by the immobilization of Bi2O3 nanodots in DFNS and the subsequent reaction with HBr and then HI vapors at room temperature. The 4 nm-Bi2O3 nanodots acted as a sacrificial template to form BiOX nanosheets by reaction with HX vapors (X = Br, I). The BiOBr/BiOI nanosheet heterojunction with the lateral size remained in the range of 90 to 110 nm and a thickness of 15 nm formed on DFNS, where the BiOBr:BiOI ratio in the product was controlled by the exposure time to HX vapors. The reaction sequence (HBr → HI vapors) was a key for the formation of BiOBr/BiOI nanosheet heterojunction with controlled composition. When the reaction of Bi2O3 nanodots with HI vapor was performed in the reverse sequence (HI→ HBr), the substitution of I- with Br- occurred to form BiOBr sheets on DFNS. The BiOBr/BiOI nanosheet heterojunction anchored on DFNS was used as a visible-light-driven photocatalyst for the decomposition of benzene in water under solar light, and its activity was superior to that of single BiOX nanosheets on DFNS.

Cellulose-based aerogel derived N, B-co-doped porous biochar for high-performance CO2 capture and supercapacitor

The remarkable characteristics of porous biochar have generated significant interest in various fields, such as CO2 capture and supercapacitors. The modification of aerogel-derived porous biochar through activation and heteroatomic doping can effectively enhance CO2 adsorption and improve supercapacitor performance. In this study, a novel N, B-co-doped porous biochar (NBCPB) was synthesized by carbonating and activating the N, B dual-doped cellulose aerogel. N and B atoms were doped in-situ using a modified alkali-urea method. The potassium citrate was served as both an activator and a salt template to facilitate the formation of a well-developed nanostructure. The optimized NBCPB-650-1 (where 650 corresponded to activation temperature and 1 represented mass ratio of potassium citrate activator to carbonized NBCPB-400 precursor) displayed the largest micropore volume of 0.40 cm3·g-1 and a high specific surface area of 891 m2·g-1, which contributed to an excellent CO2 adsorption capacity of 4.19 mmol·g-1 at 100 kPa and 25 °C, a high CO2/N2 selectivity, and exceptional reusability (retained >97.5 % after 10 adsorption-desorption cycles). Additionally, the NBCPB-650-1 electrode also delivered a high capacitance of 220.9 F·g-1 at 1 A·g-1. Notably, the symmetrical NBCPB-650-1 supercapacitor exhibited a high energy density of 9 Wh·kg-1 at the power density of 100 W·kg-1. This study not only presents the potential application of NBCPB-650-1 material in CO2 capture and electrochemical energy storage, but also offers a new insight into easy-to-scale production of heteroatomic-modified porous biochar.

Controlled synthesis of sulfhydryl-dendritic mesoporous silica nanospheres for ultrafast extraction and sensitive analysis of organochlorine herbicides containing amide groups

The distinctive morphology of dendritic mesoporous silica nanoparticles (DMSN) has recently attracted considerable attention in scientific community. However, synthesis of DMSN with well-defined structure and uniform size for ultrafast extraction of trace herbicide residues from environmental and food samples remains to be a compelling challenge. In this study, sulfhydryl functionalized dendritic mesoporous silica (SH-DMSN) was synthesized and the SH-DMSN showcases monodisperse microspheres with flower shape and precisely tailored and controllable pore sizes. This distinctive structural configuration accelerates mass transfer within the silica layer, resulting in heightened adsorption efficiencies. Furthermore, the particle sizes (455, 765, and 808) of the adsorbent can be meticulously fine-tuned by introducing distinct templates. Specifically, when the particle size is 765 nm, the optimized SH-DMSN exhibits a substantial specific surface area (691.32 m²/g), outstanding adsorption efficiencies (>90 %), remarkably swift adsorption and desorption kinetics (2 min and 3 min, respectively), and exceptional stability. The superior adsorption capabilities of this novel adsorbent, ranging from 481.65 to 1021.7 µg/g for organochlorine herbicides containing amide groups, can be attributed to the interplay of S-π interactions, halogen bonding, and electrostatic attraction interaction. These interactions involve the lone pair electrons of sulfhydryl and silanol groups with the π-electrons, halogen atoms and amide groups in herbicide molecules. This study not only offers a new perspective on advancing the practical utilization of dendritic mesoporous silica but also provides a pragmatic strategy for the separation and analysis of herbicides in diverse sample matrices.

Pt-doped Ru nanoparticles loaded on 'black gold' plasmonic nanoreactors as air stable reduction catalysts

This study introduces a plasmonic reduction catalyst, stable only in the presence of air, achieved by integrating Pt-doped Ru nanoparticles on black gold. This innovative black gold/RuPt catalyst showcases good efficiency in acetylene semi-hydrogenation, attaining over 90% selectivity with an ethene production rate of 320 mmol g-1 h-1. Its stability, evident in 100 h of operation with continuous air flow, is attributed to the synergy of co-existing metal oxide and metal phases. The catalyst's stability is further enhanced by plasmon-mediated concurrent reduction and oxidation of the active sites. Finite-difference time-domain simulations reveal a five-fold electric field intensification near the RuPt nanoparticles, crucial for activating acetylene and hydrogen. Kinetic isotope effect analysis indicates the contribution from the plasmonic non-thermal effects along with the photothermal. Spectroscopic and in-situ Fourier transform infrared studies, combined with quantum chemical calculations, elucidate the molecular reaction mechanism, emphasizing the cooperative interaction between Ru and Pt in optimizing ethene production and selectivity.

Integrated Optimization of Crystal Facets and Nanoscale Spatial Confinement toward the Boosted Catalytic Performance of Pd Nanocrystals

Tuning the surface chemical property and the local environment of nanocrystals is crucial for realizing a high catalytic performance in various reactions. Herein, we aim to elucidate the structure sensitivity of Pd facets on the surface catalytic hydrogenation reaction and to identify what role the nanoconfinement effect plays in the catalytic properties of Pd nanocrystal catalysts. By controlling the coating structures of mesoporous silica (mSiO2) on Pd nanocrystals with different exposed facets that include {100}, {111}, and {hk0}, we present a series of Pd@mSiO2 nanoreactors in core-shell and yolk-shell structures and the discovery of a partial-coated structure, which can provide different types of nanoconfinement, and we propose a seed size-dominated growth mechanism. We demonstrate that a superior activity was exhibited in Pd nanocrystals enclosed by the {hk0} facet as compared to the Pd{100} and Pd{111} facets, and substantially enhanced efficiency and stability were achieved in Pd@mSiO2 particles with yolk-shell structures, indicating a crucial superiority of optimizing the configuration of crystal facets and nanoconfinement. Our study provides an efficient strategy to rationally design and optimize nanocatalysts for promoting catalytic performance.

Dendritic mesoporous nanoparticles for the detection, adsorption, and degradation of hazardous substances in the environment: State-of-the-art and future prospects

Equipped with hierarchical pores and three-dimensional (3D) center-radial channels, dendritic mesoporous nanoparticles (DMNs) make their pore volumes extremely large, specific surface areas super-high, internal spaces especially accessible, and so on. Other entities (like organic moieties or nanoparticles) can be modified onto the interfaces or skeletons of DMNs, accomplishing their functionalization for desirable applications. This comprehensive review emphasizes on the design and construction of DMNs-based systems which serve as sensors, adsorbents and catalysts for the detection, adsorption, and degradation of hazardous substances, mainly including the construction procedures of brand-new DMNs-based materials and the involved hazardous substances (like industrial chemicals, chemical dyes, heavy metal ions, medicines, pesticides, and harmful gases). The sensitive, adsorptive, or catalytic performances of various DMNs have been compared; correspondingly, the reaction mechanisms have been revealed strictly. It is honestly anticipated that the profound discussion could offer scientists certain enlightenment to design novel DMNs-based systems towards the detection, adsorption, and degradation of hazardous substances, respectively or comprehensively.

Facile one pot synthesis of 2-substituted benzimidazole derivatives under mild conditions by using engineered MgO@DFNS as heterogeneous catalyst

Benzimidazole derivatives are considered as important heterocyclic motifs that show a wide range of pharmaceutical applications. In view of their wide-ranging bioactivities, it is imperative to direct research on the sustainable catalytic synthesis of benzimidazole. Therefore, herein, we report a novel approach for the synthesis of benzimidazole and its derivatives with engineered MgO supported on dendritic fibrous nano silica (MgO@DFNS) as a sustainable heterogeneous catalyst. The catalyst MgO@DFNS was thoroughly characterized to understand its physio-chemical properties using XRD, FE-SEM, XPS, FT-IR, zeta potential, HR-TEM, TGA, TPR and TPD. The obtained results suggested that the catalyst MgO@DFNS prepared well and have the desired characteristics in it. After the successful characterisation of the prepared catalyst MgO@DFNS, it was applied in the synthesis of benzimidazole derivatives via condensation of o-phenylenediamine, and various aromatic and aliphatic aldehydes under ambient temperature. The catalyst produced a clean reaction profile with excellent yields in a shorter time under the umbrella of green chemistry. The effect of reaction parameters such as the effect of time, catalyst dosage, loading of MgO, effect of solvents and effect of different homo and heterogeneous catalyst were also tested. Furthermore, to understand the scope of the catalyst different substituted diamines and substituted aldehydes were reacted and obtained desired products in good to efficient yield. In addition, a recyclability study was also conducted and it was observed that the catalyst could be recycled for up to six cycles without noticeable changes in the morphology and activity. We believe that the present methodology gave several advantages such as an eco-friendly method, easy work-up, good selectivity, high yields and quick recovery of catalyst. MgO@DFNS is highly stable for several cycles without significant loss of its activity, which possibly demonstrates its applicability at the industrial scale.

Real-Time Optical Tracking of Protein Corona Formation on Single Nanoparticles in Serum

The formation of a protein corona, where proteins spontaneously adhere to the surface of nanomaterials in biological environments, leads to changes in their physicochemical properties and subsequently affects their intended biomedical functionalities. Most current methods to study protein corona formation are ensemble-averaging and either require fluorescent labeling, washing steps, or are only applicable to specific types of particles. Here we introduce real-time all-optical nanoparticle analysis by scattering microscopy (RONAS) to track the formation of protein corona in full serum, at the single-particle level, without any labeling. RONAS uses optical scattering microscopy and enables real-time and in situ tracking of protein adsorption on metallic and dielectric nanoparticles with different geometries directly in blood serum. We analyzed the adsorbed protein mass, the affinity, and the kinetics of the protein adsorption at the single particle level. While there is a high degree of heterogeneity from particle to particle, the predominant factor in protein adsorption is surface chemistry rather than the underlying nanoparticle material or size. RONAS offers an in-depth understanding of the mechanisms related to protein coronas and, thus, enables the development of strategies to engineer efficient bionanomaterials.

Carbon Capture Using Porous Silica Materials

As the primary greenhouse gas, CO₂ emission has noticeably increased over the past decades resulting in global warming and climate change. Surprisingly, anthropogenic activities have increased atmospheric CO₂ by 50% in less than 200 years, causing more frequent and severe rainfall, snowstorms, flash floods, droughts, heat waves, and rising sea levels in recent times. Hence, reducing the excess CO₂ in the atmosphere is imperative to keep the global average temperature rise below 2 °C. Among many CO₂ mitigation approaches, CO₂ capture using porous materials is considered one of the most promising technologies. Porous solid materials such as carbons, silica, zeolites, hollow fibers, and alumina have been widely investigated in CO₂ capture technologies. Interestingly, porous silica-based materials have recently emerged as excellent candidates for CO₂ capture technologies due to their unique properties, including high surface area, pore volume, easy surface functionalization, excellent thermal, and mechanical stability, and low cost. Therefore, this review comprehensively covers major CO₂ capture processes and their pros and cons, selecting a suitable sorbent, use of liquid amines, and highlights the recent progress of various porous silica materials, including amine-functionalized silica, their reaction mechanisms and synthesis processes. Moreover, CO₂ adsorption capacities, gas selectivity, reusability, current challenges, and future directions of porous silica materials have also been discussed.

Defects Tune the Strong Metal-Support Interactions in Copper Supported on Defected Titanium Dioxide Catalysts for CO2 Reduction

A highly active and stable Cu-based catalyst for CO₂ to CO conversion was demonstrated by creating a strong metal-support interaction (SMSI) between Cu active sites and the TiO₂-coated dendritic fibrous nano-silica (DFNS/TiO₂) support. The DFNS/TiO₂-Cu10 catalyst showed excellent catalytic performance with a CO productivity of 5350 mmol g^-1 h^-1 (i.e., 53,506 mmol g_Cu^-1 h^-1), surpassing that of almost all copper-based thermal catalysts, with 99.8% selectivity toward CO. Even after 200 h of reaction, the catalyst remained active. Moderate initial agglomeration and high dispersion of nanoparticles (NPs) due to SMSI made the catalysts stable. Electron energy loss spectroscopy confirmed the strong interactions between copper NPs and the TiO₂ surface, supported by in situ diffuse reflectance infrared Fourier transform spectroscopy and X-ray photoelectron spectroscopy. The H₂-temperature programmed reduction (TPR) study showed α, β, and γ H₂-TPR signals, further confirming the presence of SMSI between Cu and TiO₂. In situ Raman and UV-vis diffuse reflectance spectroscopy studies provided insights into the role of oxygen vacancies and Ti³⁺ centers, which were produced by hydrogen, then consumed by CO₂, and then again regenerated by hydrogen. These continuous defect generation-regeneration processes during the progress of the reaction allowed long-term high catalytic activity and stability. The in situ studies and oxygen storage complete capacity indicated the key role of oxygen vacancies during catalysis. The in situ time-resolved Fourier transform infrared study provided an understanding of the formation of various reaction intermediates and their conversion to products with reaction time. Based on these observations, we have proposed a CO₂ reduction mechanism, which follows a redox pathway assisted by hydrogen.

Role of fiber density of amine functionalized dendritic fibrous nanosilica on CO2 capture capacity and kinetics

Textural properties of the solid sorbents are critical to tuning their CO2 capture performance. In this work, we studied the effect of fiber density (in turn, pore size, distribution, and accessibility) on CO2 capture capacity and kinetics. CO2 solid sorbents were prepared by physisorption of tetraethylenepentamine (TEPA) molecules on dendritic fibrous nanosilica (DFNS) with varying fiber density. Among the various DFNS, the DFNS with moderate fiber density [DFNS-3] showed the best CO2 capture capacity under the flue gas condition. The maximum CO2 capture capacity achieved was 24.3 wt % (5.53 mmol/g) at 75 °C for DFNS-3 under humid gas conditions. Fiber density also played a role in the kinetics of CO2 capture. DFNS-1 with dense fiber density needed ∼10.4 min to reach 90 % capture capacity, while DFNS-3 (moderate fiber density) needed only 6.4 min, which further decreased to 5.9 min for DFNS-5 with lightly dense fibers. The DFNS-impregnated TEPA also showed good recyclability during 21 adsorption and desorption cycles under humid and dry conditions. The total CO2 capture capacity of DFNS-3 (14.7) in 21 cycles was 108.9 and 105.0 mmol/g under humid and dry conditions, respectively. Adsorption lifetime calculation and recyclability confirmed the fiber density-dependent CO2 capture performance.

Insights into the CO2 Capture Characteristics within the Hierarchical Pores of Carbon Nanospheres Using Small-Angle Neutron Scattering

Understanding adsorption processes at the molecular level has transformed the discovery of engineered materials for maximizing gas storage capacity and kinetics in adsorption-based carbon capture applications. In this work, we studied the molecular mechanism of gas (CO₂, H₂, methane, and ethane) adsorption inside an interconnected porous network of carbon. This was achieved by synthesizing novel macro-meso-microporous carbon (M³C) nanospheres with interconnected pore structures. The M³Cs showed a CO₂ capture capacity of 5.3 mmol/g at atmospheric CO₂ pressure, with excellent kinetics. This was due to fast CO₂ adsorption within the interconnected hierarchical macro-meso-microporous M³C. In situ small-angle neutron scattering (SANS) under various CO₂ pressures indicated that the macro- and mesopores of M³C enable fast diffusion of CO₂ molecules inside the micropores, where adsorbed CO₂ molecules densify into a liquid-like state. This strong densification of CO₂ molecules causes fast CO₂ diffusion in the macro- and mesopores of M³C, restarting the adsorption cycle for fresh CO₂ molecules until all pores are completely filled. Notably, M³C also showed good capture capacities for hydrogen and various hydrocarbons, with excellent selectivity toward ethane over methane.

Nickel-Laden Dendritic Plasmonic Colloidosomes of Black Gold: Forced Plasmon Mediated Photocatalytic CO2 Hydrogenation

In this work, we have designed and synthesized nickel-laden dendritic plasmonic colloidosomes of Au (black gold-Ni). The photocatalytic CO₂ hydrogenation activities of black gold-Ni increased dramatically to the extent that measurable photoactivity was only observed with the black gold-Ni catalyst, with a very high photocatalytic CO production rate (2464 ± 40 mmol g_Ni^-1 h^-1) and 95% selectivity. Notably, the reaction was carried out in a flow reactor at low temperature and atmospheric pressure without external heating. The catalyst was stable for at least 100 h. Ultrafast transient absorption spectroscopy studies indicated indirect hot-electron transfer from the black gold to Ni in less than 100 fs, corroborated by a reduction in Au-plasmon electron-phonon lifetime and a bleach signal associated with Ni d-band filling. Photocatalytic reaction rates on excited black gold-Ni showed a superlinear power law dependence on the light intensity, with a power law exponent of 5.6, while photocatalytic quantum efficiencies increased with an increase in light intensity and reaction temperature, which indicated the hot-electron-mediated mechanism. The kinetic isotope effect (KIE) in light (1.91) was higher than that in the dark (∼1), which further indicated the electron-driven plasmonic CO₂ hydrogenation. Black gold-Ni catalyzed CO₂ hydrogenation in the presence of an electron-accepting molecule, methyl-p-benzoquinone, reduced the CO production rate, asserting the hot-electron-mediated mechanism. Operando diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) showed that CO₂ hydrogenation took place by a direct dissociation path via linearly bonded Ni-CO intermediates. The outstanding catalytic performance of black gold-Ni may provide a way to develop plasmonic catalysts for CO₂ reduction and other catalytic processes using black gold.

A novel pH- and glutathione-responsive drug delivery system based on in situ growth of MOF199 on mesoporous organic silica nanoparticles targeting the hepatocellular carcinoma niche

Background

For people with advanced hepatocellular carcinoma (HCC), systemic chemotherapy remains the only choice of palliative treatment. However, chemotherapy efficacy is not effective due to its short blood circulation times, nonspecific cell and tissue biodistribution, and rapid metabolism or excretion from the body. Therefore, a targeted nanomedicine delivery system is urgently needed.

Methods

In order to improve the treatment efficiency of HCC, based on in situ growth of a copper metal organic framework on mesoporous organic silica nanoparticles, dual pH- and glutathione (GSH)-responsive multifunctional nanocomposites were synthesized as nanocarriers for enhanced HCC therapy. In this research, cellular uptake studies were performed using CLSM and Bio-TEM observations. Flow cytometry, AO-EB fluorescent staining, EdU test and Western blot were utilized to explore the apoptosis and proliferation process. In vivo imaging was employed to research the distribution of the nanocomposites in HCC tumor-bearing nude mice and the xenograft model of HCC tumor-bearing nude mice was applied to investigate the anti-tumor effects of drug-loaded nanocomposites in vivo.

Results

This newly constructed degradable nanocomposite DOX/SOR@SP94 and mPEG-anchored MONs@MOF199 (D/S@SPMM) has the benefits of controllable pore size, high encapsulation efficiency, and precise targeting. According to the results of in vivo imaging and anti-tumor studies, as well as pharmacokinetic research, D/S@SPMM possessed precise HCC tumor targeting and long-lasting accumulation properties at the tumor region. Compared with traditional chemotherapy and non-targeted drug delivery systems, anti-tumor efficiency was increased by approximately 10- and 5-fold, respectively. The nanocomposites exhibited excellent anti-tumor properties without inducing observable systemic toxicity, owing to efficient DOX and SOR loading and release as well as the HCC specific targeting peptide SP94.

Conclusions

The in vitro and in vivo anti-tumor results indicated that these nanocomposites could be an efficient nanomedicine for targeting HCC therapy.

Multicolor Super-Resolution Microscopy of Protein Corona on Single Nanoparticles

Nanoparticles represent a promising class of material for nanomedicine and molecular biosensing. The formation of a protein corona due to nonspecific particle-protein interactions is a determining factor for the biological fate of nanoparticles in vivo and strongly impacts the performance of nanoparticles when used as biosensors. Nonspecific interactions are usually highly heterogeneous, yet little is known about the heterogeneity of the protein corona that may lead to inter- and intraparticle differences in composition and protein distribution. Here, we present a super-resolution microscopic approach to study the protein corona on single silica nanoparticles and subsequent cellular interactions using multicolor stimulated emission depletion (STED) microscopy. We demonstrate that STED resolves structural features of protein corona on single particles including the distribution on the particle surface and the degree of protein internalization in porous particles. Using multicolor measurements of multiple labeled protein species, we determine the composition of the protein corona at the single-particle level. We quantify particle-to-particle differences in the composition and find that the composition is considerably influenced by the particle geometry. In a subsequent cellular uptake measurement, we demonstrate multicolor STED of protein corona on single particles internalized by cells. Our study shows that STED microscopy opens the window toward mechanistic understanding of protein coronas and aids in the rational design of nanoparticles as nanomedicines and biosensors.

Technological trends in nanosilica synthesis and utilization in advanced treatment of water and wastewater

Water and wastewater treatment applications stand to benefit immensely from the design and development of new materials based on silica nanoparticles and their derivatives. Nanosilica possesses unique properties, including low toxicity, chemical inertness, and excellent biocompatibility, and can be developed from a variety of sustainable precursor materials. Herein, we provide an account of the recent advances in the synthesis and utilization of nanosilica for wastewater treatment. This review covers key physicochemical aspects of several nanosilica materials and a variety of nanotechnology-enabled wastewater treatment techniques such as adsorption, separation membranes, and antimicrobial applications. It also discusses the prospective design and tuning options for nanosilica production, such as size control, morphological tuning, and surface functionalization. Informative discussions on nanosilica production from agricultural wastes have been offered, with a focus on the synthesis methodologies and pretreatment requirements for biomass precursors. The characterization of the different physicochemical features of nanosilica materials using critical surface analysis methods is discussed. Bio-hybrid nanosilica materials have also been highlighted to emphasize the critical relevance of environmental sustainability in wastewater treatment. To guarantee the thoroughness of the review, insights into nanosilica regeneration and reuse are provided. Overall, it is envisaged that this work's insights and views will inspire unique and efficient nanosilica material design and development with robust properties for water and wastewater treatment applications.

Tunable synthesis of dendritic fibrous nano silica using 1-pentanol-water microemulsion at low oil to water ratio

Dendritic fibrous nanosilica (DFNS) is a suitable nano-carrier for loading pesticides with radially oriented pores and a large surface area. The microemulsion method is standard method to prepare DFNS, and 1-pentanol is taken to replace cyclohexane as an oil solvent due to its high stability and nontoxic property. The results showed that the volume ratio of 1-pentanol (oil) to water (O/W) and the molar ratio of hexadecyltrimethylammonium bromide (CTAB) to tetraethylorthosilicate (TEOS) had effected on morphology and adsorption properties of DFNS in the water-CTAB-1-pentanol-ethanol-trimethylbenzene (TMB) microemulsion system. DFNS with bicontinuous concentric lamellar morphologies can be synthesized in this microemulsion at the meager O/W volume ratio (0.025-0.045). It features a tight mesoporous structure with a thin dendritic fibrous in 0.03 to 0.04 O/W volume ratio. The particle sizes, surface areas, and porosity of DFNS were positively correlated with the addition of the silica precursor TEOS. The size of DFNS increased from 123 to about 220 nm with the CTAB/TEOS molar ratio decreasing from 0.119 to 0.050. When the molar ratio of CTAB to TEOS  = 0.119, DFNS has a smaller particle size (123 nm) with a larger surface area and abundant honeycomb mesopores; the low O/W volume ratio strategy provides theoretical support for the industrialization development of DFNS and nano-pesticides, which plays a profound role in promoting the sustainable development of pesticide reduction, efficiency and green agriculture.

Dendritic Fibrous Nanosilica: Discovery, Synthesis, Formation Mechanism, Catalysis, and CO2 Capture-Conversion

ConspectusSilica-based mesoporous nanomaterials have been widely used for a range of applications. Although mesopore materials (such as MCM-41 and SBA-15) possess high surface area, due to their tubular pore structures, pore accessibility is restricted, which causes limitations in mass transport. A new nanosilica was needed to overcome these challenges, including better accessibility, controllable particle size, and good stability. In 2010, my group invented dendritic fibrous nanosilica (DFNS), which has now become a family of novel nanosilicas. DFNS has several unique properties: (i) Tunable particle sizes (50 to 1200 nm), (ii) high surface area (500 to 1200 m²/g), (iii) tunable pore volume (0.32 to 2.18 cm³/g), (iv) wide pore size distribution (3.7 to 25 nm) characterized by radially oriented pores, (v) controllable fiber density (number of fibers per sphere), (vi) variable pore size and pore volume, (vi) high thermal (∼800 °C) and hydrothermal stability, and (vii) mechanical stability (∼130 MPa). DFNS possesses unique dendritic fibrous morphology, and hence can be reached from all sides and easily accessible. DFNS can now be synthesized using a open refluxing protocol, which allowed the scale-up of the process with a sustainable E-factor. In the last 12 years, the DFNS family of materials has been extensively studied for their formation mechanism and range of applications such as catalysis, solar energy harvesting, CO₂ capture, CO₂ conversion, sensing, biomedicine, energy storage and many more.This Account discusses the invention of DFNS, its synthesis with tunable particle size, textural properties (surface area, pore volume, and pore size), and fiber density. In addition, the DFNS formation mechanism via the complex interplay of self-assembly, the dynamics, and coalescence of bicontinuous microemulsion droplets (BMDs) is discussed. Finally, applications of DFNS in a range of fields, that include catalysis, photocatalysis, synthesis of plasmonic black gold, nanosponges of aluminosilicates, CO₂ capture, and CO₂ conversion to fuel, are presented.

Synergistic Effects of Earth-Abundant Metal-Metal Oxide Enable Reductive Amination of Carbonyls at 50 °C

Reductive amination of carbonyls to primary amines is of importance to the synthesis of fine chemicals; however, this reaction with heterogeneous catalysts containing earth-abundant metals under mild conditions remains scarce. Here, we show that the nickel catalyst with mixed oxidation states enables such synthesis of primary amines under low temperature (50 °C) and H₂ pressure (0.9 MPa). The catalyst shows activity in both water and toluene. The high activity likely results from the formation of small (ca. 4.6 nm) partially oxidized nickel nanoparticles (NPs) homogeneously anchored onto the silica and their synergistic effect. Detailed characterizations indicate stabilization of NPs through strong metal support interaction via electron donation from the metal to support. We identify that the support endowed with an amphoteric nature shows better performance. This strategy of making small metal-metal oxide NPs will open an avenue toward the rational development of efficient catalysts that would allow for other organic transformations under mild reaction conditions.

Straightforward synthesis of multifunctional porous polymer nanomaterials for CO2 capture and removal of contaminants

A straightforward synthesis of multifunctional mesoporous polymer nanomaterials suitable for the removal of contaminants and CO2 capture is reported.

Dendritic Fibrous Colloidal Silica Internally Cross-linked by Bivalent Organic Cations: An Efficient Support for Dye Removal and the Reduction of Nitrobenzene Derivatives

We designed a new unique amphoteric monodisperse colloid with a large complex internal structure, in which silica surfaces are bridged with an organic cross-linker. The rationale was that such colloids would be excellent adsorbents for cationic and anionic dyes and, when doped with noble metal nanoparticles, would be an excellent catalyst for the reduction of a variety of organic compounds. In the first step, the organo-silica bridging agent (bivalent organic cross-linkers) DABCO-S (silanated DABCO) was prepared through a simple nucleophilic substitution reaction between (3-chloropropyl)triethoxysilane and bivalent 1,4-diazabicyclo[2.2.2]octane (DABCO) (a strong base). In the second step, a DABCO-S bridge was introduced into dendritic fibrous nanostructured colloidal silica (DFNS) under open-vessel reflux conditions. We refer to the product obtained by incorporating DABCO-S in DFNS as DDS. The unique characteristics of DFNS are completely preserved in this new type of periodic mesoporous organo-silica-DFNS. The produced nanocomposite has a high surface area of about 807 m² g^-1, a large pore volume of 1.9 cm³ g^-1, and a bimodal pore size distribution, with small 2.5 nm pores and large 30 nm pores. As such, DDS is an efficient adsorbent for dye removal from wastewater. The results show that DDS can adsorb positive and negative dyes such as methylene blue, orange II sodium salt (OR), and procion red mx-58 (PR) with a capacity of 678, 3192, and 3190 mg dye/g adsorbent. Introducing silver nanoparticles in situ into DDS leads to a composite with excellent accessibility of reactants to the Ag surface, resulting in an efficient catalytic reduction of nitro aromatic compounds (NACs) in aqueous media.

Stepping towards benign alternatives: sustainable conversion of plastic waste into valuable products

The extensive use of plastic and the absence of efficient and sustainable methods for its degradation has raised critical concerns about its disposal and degradation. Furthermore, the escalated use of personal protective equipment (PPE) and masks during the ongoing COVID-19 pandemic has put us under tremendous pressure of generating huge amounts of plastic waste. Traditional plastic waste disintegration protocols, while effective, pose additional inevitable environmental risks. Owing to this, almost all the used plastic is directly discarded into the marine and terrestrial bodies, causing great harm to the flora and fauna. Plastic has even started entering the food chain in the form of micro- and nano-plastics, leading to deleterious effects. Considering the global need for finding sustainable ways to degrade plastic, several approaches have been developed. Herein we highlight and rationally compare the recent reports on the development of benign alternatives for the sustainable disintegration of plastic detritus into value-added products. Here we discuss, in depth, photoreforming of a variety of polymers to liquid fuels under natural conditions; enzyme-based deconstruction of polymeric materials via microorganisms and their engineered mutants into useful virgin monomers at ambient temperature; and pyrocatalytic degradation of polyethylene through efficient synthetic materials into valuable fuels and waxes. By critically analyzing the methods, we also provide our opinion on such sustainable techniques and discuss newer approaches related to bioinspired and biomimetic chemistry principles for the management of plastic waste.

Formation of BiOX (X = Cl and Br) in a mesoporous silica by the infiltration of Bi salts and the subsequent reaction with HX vapor

The formation of BiOX (X = Br and Cl) nanoparticles in a mesoporous silica (SBA-15) was found by the reaction of the infiltrated bismuth oxo species with HX vapor at room temperature. The cylindrical pores of SBA-15 led to the directional growth of BiOX nanorods and control of the particle diameter.

Origin of the Hierarchical Structure of Dendritic Fibrous Nanosilica: A Small-Angle X-ray Scattering Perspective

The discovery of dendritic fibrous nanosilica (DFNS) has attracted great attention to the field of catalysis, CO₂ capture, drug delivery due to its distinct morphology, and pore size distribution. Despite extensive research, the understanding of the DFNS formation process and its internal structure remains incomplete as microscopy and gas sorption techniques were not able to provide necessary in-depth structural information due to their inherent limitations. In the current work, we present a structural model of DFNS derived using small-angle X-ray scattering (SAXS) supported by ¹²⁹Xe nuclear magnetic resonance (NMR), which provided intricate details of DFNS and its internal structure. Mechanistic understanding of the DFNS formation and growth process was achieved by performing time-resolved SAXS measurements during the synthesis of DFNS, which unveils the evolution of two levels of a bicontinuous microemulsion structure responsible for intricate DFNS morphology. The validity and the accuracy of the SAXS method and the model were successfully established through a direct correlation among the functionality of the DFNS scattering profile and its pore size distribution, as well as results obtained from the ¹²⁹Xe NMR studies. It has been established that the DFNS structure originates from direct modulation of the bicontinuous structure controlled by a surfactant, a co-surfactant, and the silicate species formed during hydrolysis and the condensation reaction of the silica precursor.

Biotemplated Hollow Mesoporous Silica Particles as Efficient Carriers for Drug Delivery

We designed three types of hollow-shaped porous silica materials via a three-step biotemplate-directed method: porous hollow silica nanorods, hollow dendritic fibrous nanostructured silica (DFNS), and ultraporous sponge-like DFNS. The first step was making a biotemplate, for which we used cellulose nanocrystals (CNCs), consisting of rod-shaped nanoparticles synthesized by conventional acid hydrolysis of cellulose fibers. In a second step, core-shell samples were prepared using CNC particles as hard template by two procedures. In the first one, core-shell CNC-silica nanoparticles were synthesized by a polycondensation reaction, which exclusively took place at the surface of the CNCs. In the second procedure, a typical synthesis of DFNS was conducted in a bicontinuous microemulsion with the assistance of additives. DFNS was assembled on the surface of the CNCs, giving rise to core-shell CNC-DFNS structures. Finally, all of the silica-coated CNC composites were calcined, during which the CNC was removed from the core and hollow structures were formed. These materials are very lightweight and highly porous. All three structures were tested as nanocarriers for drug delivery and absorbents for dye removal applications. Dye removal results showed that they can adsorb methylene blue efficiently, with ultraporous sponge-like DFNS showing the highest adsorption capacity, followed by hollow DFNS and hollow silica nanorods. Furthermore, breast cancer cells show a lower cell viability when exposed to doxorubicin-loaded hollow silica nanorods compared with control or doxorubicin cultures, suggesting that the loaded nanorod has a greater anticancer effect than free doxorubicin.

Direct CO2 capture and conversion to fuels on magnesium nanoparticles under ambient conditions simply using water

Converting CO₂ directly from the air to fuel under ambient conditions is a huge challenge. Thus, there is an urgent need for CO₂ conversion protocols working at room temperature and atmospheric pressure, preferentially without any external energy input. Herein, we employ magnesium (nanoparticles and bulk), an inexpensive and the eighth-most abundant element, to convert CO₂ to methane, methanol and formic acid, using water as the sole hydrogen source. The conversion of CO₂ (pure, as well as directly from the air) took place within a few minutes at 300 K and 1 bar, and no external (thermal, photo, or electric) energy was required. Hydrogen was, however, the predominant product as the reaction of water with magnesium was favored over the reaction of CO₂ and water with magnesium. A unique cooperative action of Mg, basic magnesium carbonate, CO₂, and water enabled this CO₂ transformation. If any of the four components was missing, no CO₂ conversion took place. The reaction intermediates and the reaction pathway were identified by ¹³CO₂ isotopic labeling, powder X-ray diffraction (PXRD), nuclear magnetic resonance (NMR) and in situ attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR), and rationalized by density-functional theory (DFT) calculations. During CO₂ conversion, Mg was converted to magnesium hydroxide and carbonate, which may be regenerated. Our low-temperature experiments also indicate the future prospect of using this CO₂-to-fuel conversion process on the surface of Mars, where CO₂, water (ice), and magnesium are abundant. Thus, even though the overall process is non-catalytic, it could serve as a step towards a sustainable CO₂ utilization strategy as well as potentially being a first step towards a magnesium-driven civilization on Mars.

We demonstrated the use of magnesium nanoparticles (and bulk) to convert CO₂ (pure & also from the air) to methane, methanol, formic acid and green cement without external energy within a few minutes, using only water as the sole hydrogen source.

Boronic Acid Functionalized Nanosilica for Binding Guest Molecules

Dendritic fibrous nanosilica (DFNS) has very high surface area and well-defined nanochannels; therefore, it is very useful as supporting material for numerous applications including catalysis, sensing, and bioseparation. Due to the highly restricted space, addition of molecular ligands to DFNS is very challenging. This work studies how ligand conjugation in nanoscale pores in DFNS can be achieved through copper-catalyzed click reaction, using an optional, in situ synthesized, temperature-responsive polymer intermediate. A clickable boronic acid is used as a model to investigate the ligand immobilization and the molecular binding characteristics of the functionalized DFNS. The morphology, composition, nanoscale pores, and specific surface area of the boronic acid functionalized nanosilica were characterized by electron microscopy, thermogravimetric and elemental analysis, Fourier transform infrared spectroscopy, and nitrogen adsorption-desorption measurements. The numbers of boronic acid molecules on the modified DFNS with and without the polymer were determined to be 0.08 and 0.68 mmol of ligand/g of DFNS, respectively. We also studied the binding of small cis-diol molecules in the nanoscale pores of DFNS. The boronic acid modified DFNS with the polymer intermediate exhibits higher binding capacity for Alizarin Red S and nicotinamide adenine dinucleotide than the polymer-free DFNS. The two types of boronic acid modified DFNS can bind small cis-diol molecules in the presence of large glycoproteins, due in large part to the effect of size exclusion provided by the nanochannels in the DFNS.

Nitrogen doped carbon spheres with wrinkled cages for the selective oxidation of 5-hydroxymethylfurfural to 5-formyl-2-furancarboxylic acid

Nitrogen doped carbon spheres with wrinkled cages (NCSWCs), which were used for the first time as metal-free catalysts, exhibited high catalytic activity and selectivity in the oxidation of 5-hydroxymethylfurfural (HMF) to 5-formyl-2-furancarboxylic acid (FFCA) under base-free conditions using tert-butyl hydroperoxide (TBHP) as the oxidant. The mechanistic studies found that this reaction was catalyzed by the synergy between NCSWCs and TBHP. The density functional theory (DFT) calculations further suggested that the hydroperoxyl radicals from TBHP adsorbed on the carbon atoms adjacent to the graphitic N atoms are the active sites.

Lithium silicate nanosheets with excellent capture capacity and kinetics with unprecedented stability for high-temperature CO2 capture

An excessive amount of CO₂ is the leading cause of climate change, and hence, its reduction in the Earth's atmosphere is critical to stop further degradation of the environment. Although a large body of work has been carried out for post-combustion low-temperature CO₂ capture, there are very few high temperature pre-combustion CO₂ capture processes. Lithium silicate (Li₄SiO₄), one of the best known high-temperature CO₂ capture sorbents, has two main challenges, moderate capture kinetics and poor sorbent stability. In this work, we have designed and synthesized lithium silicate nanosheets (LSNs), which showed high CO₂ capture capacity (35.3 wt% CO₂ capture using 60% CO₂ feed gas, close to the theoretical value) with ultra-fast kinetics and enhanced stability at 650 °C. Due to the nanosheet morphology of the LSNs, they provided a good external surface for CO₂ adsorption at every Li-site, yielding excellent CO₂ capture capacity. The nanosheet morphology of the LSNs allowed efficient CO₂ diffusion to ensure reaction with the entire sheet as well as providing extremely fast CO₂ capture kinetics (0.22 g g⁻¹ min⁻¹). Conventional lithium silicates are known to rapidly lose their capture capacity and kinetics within the first few cycles due to thick carbonate shell formation and also due to the sintering of sorbent particles; however, the LSNs were stable for at least 200 cycles without any loss in their capture capacity or kinetics. The LSNs neither formed a carbonate shell nor underwent sintering, allowing efficient adsorption–desorption cycling. We also proposed a new mechanism, a mixed-phase model, to explain the unique CO₂ capture behavior of the LSNs, using detailed (i) kinetics experiments for both adsorption and desorption steps, (ii) in situ diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy measurements, (iii) depth-profiling X-ray photoelectron spectroscopy (XPS) of the sorbent after CO₂ capture and (iv) theoretical investigation through systematic electronic structure calculations within the framework of density functional theory (DFT) formalism.

Capturing CO₂ before its release. Lithium silicate nanosheets showed high CO₂ capture capacity (35.3 wt%) with ultra-fast kinetics (0.22 g g⁻¹ min⁻¹) and enhanced stability at 650 °C for at least 200 cycles, due to mixed-phase-model of CO₂ capture.

Dendrons containing boric acid and 1,3,5-tris(2-hydroxyethyl)isocyanurate covalently attached to silica-coated magnetite for the expeditious synthesis of Hantzsch esters

A new multifunctional dendritic nanocatalyst containing boric acid and 1,3,5-tris(2-hydroxyethyl)isocyanurate covalently attached to core-shell silica-coated magnetite (Fe3O4@SiO2@PTS-THEIC-(CH2)3OB(OH)2) was designed and properly characterized by different spectroscopic or microscopic methods as well as analytical techniques used for mesoporous materials. It was found that the combination of both aromatic π-π stacking and boron-oxygen ligand interactions affords supramolecular arrays of dendrons. Furthermore, the use of boric acid makes this dendritic catalyst a good choice, from corrosion, recyclability and cost points of view. The catalytic activity of Fe3O4@SiO2@PTS-THEIC-(CH2)3OB(OH)2, as an efficient magnetically recoverable catalyst, was investigated for the synthesis of polyhydroacridines (PHAs) as well as polyhydroquinolines (PHQs) via one-pot multicomponent reactions of dimedone and/or ethyl acetoacetate, different aldehydes and ammonium acetate in EtOH under reflux conditions. Very low loading of the catalyst, high to quantitative yields of the desired PHAs or PHQs products, short reaction times, wide scope of the substrates, eliminating any toxic heavy metals or corrosive reagents for the modification of the catalyst, and simple work-up procedure are remarkable advantages of this green protocol. An additional advantage of this magnetic nanoparticles catalyst is its ability to be separated and recycled easily from the reaction mixture with minimal efforts in six subsequent runs without significant loss of its catalytic activity. This magnetic and dendritic catalyst can be extended to new two- and three-dimensional covalent organic frameworks with different applications.

Controlled release evaluation of paracetamol loaded amine functionalized mesoporous silica KCC1 compared to microcrystalline cellulose based tablets

In the pharmaceutical manufacturing, drug release behavior development is remained as one of the main challenges to improve the drug effectiveness. Recently, more focus has been done on using mesoporous silica materials as drug carriers for prolonged and superior control of drug release in human body. In this study, release behavior of paracetamol is developed using drug-loaded KCC-1-NH2 mesoporous silica, based on direct compaction method for preparation of tablets. The purpose of this study is to investigate the utilizing of pure KCC-1 mesoporous silica (KCC-1) and amino functionalized KCC-1 (KCC-1-NH2) as drug carriers in oral solid dosage formulations compared to common excipient, microcrystalline cellulose (MCC), to improve the control of drug release rate by manipulating surface chemistry of the carrier. Different formulations of KCC-1 and KCC-NH2 are designed to investigate the effect of functionalized mesoporous silica as carrier on drug controlled-release rate. The results displayed the remarkable effect of KCC-1-NH2 on drug controlled-release in comparison with the formulation containing pure KCC-1 and formulation including MCC as reference materials. The pure KCC-1 and KCC-1-NH2 are characterized using different evaluation methods such as FTIR, SEM, TEM and N2 adsorption analysis.

Iron oxide (Fe3O4) magnetic nanoparticles supported on wrinkled fibrous nanosilica (WFNS) functionalized by biimidazole ionic liquid as an effective and reusable heterogeneous magnetic nanocatalyst for the efficient synthesis of N-sulfonylamidines

Wrinkled fibrous nanosilica (WFNS) which functionalized by ionic liquid modified Fe3O4 NPs and CuI salts has been synthesized and characterized with FE-SEM, TEM, FT-IR, FAAS, EDX, and, XRD, VSM, and BET-BJH analysis. This new and effective magnetic ceramic nanocatalyst has been applied towards rapid synthesis of N-sulfonylamidines using reaction of phenyl acetylene, substituted sulfonyl azide and various amines under solvent-free conditions in very short reaction time. Higher catalytic activity CuI/Fe3O4NPs@IL-DFNS in the reaction is because of special structure of DFNS and existence of ionic liquids on its pores which act as a robust anchors to the loaded various nano-particles. So, this lead to no leaching of them from the pore of the composite. Shorter reaction time, higher yield, recovery of the catalyst using an external magnet and its reusability for 8 series without noteworthy reduction in its activity are the advantages of newly synthetic catalyst toward efficient synthesis of N-sulfonylamidines.

Dendritic Fibrous Nanosilica (DFNS) for RNA Extraction from Cells

Efficient RNA extraction is critical for all downstream molecular applications and techniques. Despite the availability of several commercial kits, there is an enormous scope to develop novel materials that have high binding and elution capacities. Here, we show that RNA from the cells can be extracted by dendritic fibrous nanosilica (DFNS) with higher efficiency than commercially available silicas. This could be because of the unique fibrous morphology, high accessible surface area, and nanosize particles of DFNS. We studied various fundamental aspects, including the role of particle size, morphology, surface area, and charge on the silica surface in RNA extraction efficiency. Fourier transform infrared (FTIR) spectroscopy studies revealed the interaction of functional groups of RNA with the silica surface, causing selective binding. Due to the sustainable synthesis protocol of DFNS and the simplicity of various buffers and washing solutions used, this RNA extraction kit can be assembled in any lab. In addition to the fundamental aspects of DFNS-RNA interactions, this study has the potential to initiate the development of indigenous DFNS-based kits for RNA extraction.

Biomedical applications of dendritic fibrous nanosilica (DFNS): recent progress and challenges

Dendritic fibrous nanosilica (DFNS), with multi-component and hierarchically complex structures, has recently been receiving significant attention in various fields of nano-biomedicine. DFNS is an emerging class of mesoporous nanoparticles that has attracted great interest due to unique structures such as open three-dimensional dendritic superstructures with large pore channels and highly accessible internal surface areas. This overview aims to study the application of DFNS towards biomedical investigations. This review is divided into four main sections. Sections 1–3 are related to the synthesis and characterization of DFNS. The biomedical potential of DFNS, such as cell therapy, gene therapy, immune therapy, drug delivery, imaging, photothermal therapy, bioanalysis, biocatalysis, and tissue engineering, is discussed based on advantages and limitations. Finally, the perspectives and challenges in terms of controlled synthesis and potential nano-biomedical applications towards future studies are discussed.

Dendritic fibrous nanosilica (DFNS) , with multi-component and hierarchically complex structures, has recently been receiving significant attention in various fields of nano-biomedicine.

Catalytic nanosponges of acidic aluminosilicates for plastic degradation and CO2 to fuel conversion

The synthesis of solid acids with strong zeolite-like acidity and textural properties like amorphous aluminosilicates (ASAs) is still a challenge. In this work, we report the synthesis of amorphous "acidic aluminosilicates (AAS)", which possesses Brønsted acidic sites like in zeolites and textural properties like ASAs. AAS catalyzes different reactions (styrene oxide ring-opening, vesidryl synthesis, Friedel-Crafts alkylation, jasminaldehyde synthesis, m-xylene isomerization, and cumene cracking) with better performance than state-of-the-art zeolites and amorphous aluminosilicates. Notably, AAS efficiently converts a range of waste plastics to hydrocarbons at significantly lower temperatures. A Cu-Zn-Al/AAS hybrid shows excellent performance for CO₂ to fuel conversion with 79% selectivity for dimethyl ether. Conventional and DNP-enhanced solid-state NMR provides a molecular-level understanding of the distinctive Brønsted acidic sites of these materials. Due to their unique combination of strong acidity and accessibility, AAS will be a potential alternative to zeolites.

Surface functionalization on nanoparticles via atomic layer deposition

As an ultrathin film preparation method, atomic layer deposition (ALD) has recently found versatile applications in fields beyond semiconductors, such as energy, environment, catalysis and so on. The design, preparation and characterization of thin film applied in the emerging fields have attracted great interests. The development of ALD technique on particles opens up a broad horizon in the advanced nanofabrication. Pioneering applications are exploring conformal coating, porous coating and selective surface modification of nanoparticles. Conformal encapsulation of particles is a major application to protect materials with ultrathin films from being eroded by the external environment while keeping the original properties of the primary particles. Porous coating has been developed to simultaneously expose the particles' surface and provide nanopores, which is another important method that demonstrates its advantages in modification of electrode materials, catalysis and energy applications, etc. Selective ALD takes the method forward in order to precisely control the directionality of decoration sites on the particles and selectively passivate undesired facets, sites, or defects. Such methods provide practical strategies for atomic scale and precise surface functionalization on particles and greatly expand its potential applications.

Defects in nanosilica catalytically convert CO2 to methane without any metal and ligand

Active and stable metal-free heterogeneous catalysts for CO₂ fixation are required to reduce the current high level of carbon dioxide in the atmosphere, which is driving climate change. In this work, we show that defects in nanosilica (E' centers, oxygen vacancies, and nonbridging oxygen hole centers) convert CO₂ to methane with excellent productivity and selectivity. Neither metal nor complex organic ligands were required, and the defect alone acted as catalytic sites for carbon dioxide activation and hydrogen dissociation and their cooperative action converted CO₂ to methane. Unlike metal catalysts, which become deactivated with time, the defect-containing nanosilica showed significantly better stability. Notably, the catalyst can be regenerated by simple heating in the air without the need for hydrogen gas. Surprisingly, the catalytic activity for methane production increased significantly after every regeneration cycle, reaching more than double the methane production rate after eight regeneration cycles. This activated catalyst remained stable for more than 200 h. Detailed understanding of the role of the various defect sites in terms of their concentrations and proximities as well as their cooperativity in activating CO₂ and dissociating hydrogen to produce methane was achieved.

Controlling protein interactions in blood for effective liver immunosuppressive therapy by silica nanocapsules

Immunosuppression with glucocorticoids is a common treatment for autoimmune liver diseases and after liver transplant, which is however associated with severe side-effects. Targeted delivery of glucocorticoids to inflammatory cells, e.g. liver macrophages and Kupffer cells, is a promising approach for minimizing side effects. Herein, we prepare core-shell silica nanocapsules (SiO₂ NCs) via a sol-gel process confined in nanodroplets for targeted delivery of dexamethasone (DXM) for liver immunosuppressive therapy. DXM with concentrations up to 100 mg mL^-1 in olive oil are encapsulated while encapsulation efficiency remains over 95% after 15 days. Internalization of NCs by non-parenchymal murine liver cells significantly reduces the release of inflammatory cytokines, indicating an effective suppression of inflammatory response of liver macrophages. Fluorescent and magnetic labeling of the NCs allows for monitoring their intracellular trafficking and biodegradation. Controlled interaction with blood proteins and good colloidal stability in blood plasma are achieved via PEGylation of the NCs. Specific proteins responsible for stealth effect, such as apolipoprotein A-I, apolipoprotein A-IV, and clusterin, are present in large amounts on the PEGylated NCs. In vivo biodistribution investigations prove an efficient accumulation of NCs in the liver, underlining the suitability of the SiO₂ NCs as a dexamethasone carrier for treating inflammatory liver diseases.

Growth of Cu-BTC MOFs on dendrimer-like porous silica nanospheres for the catalytic aerobic epoxidation of olefins

DPSNs@Cu-BTC was achieved using dendrimer-like porous silica nanoparticles as a support and as an efficient catalyst for olefin epoxidation.

Dendritic fibrous nano-silica & titania (DFNST) spheres as novel cataluminescence sensing materials for the detection of diethyl ether

Selective and controllable cataluminescence (CTL) sensors for volatile organic compounds (VOCs) are significant for chemical safety, environmental monitoring, health effects on human beings, and so forth. Most of the exploited CTL-based sensors suffer relatively low response and poor selectivity because of their high sensitivities to interferential substances. In this investigation, dendritic fibrous nano-silica & titania (DFNST) spheres have been synthesized as novel sensing materials and the corresponding DFNST-based CTL sensor has been fabricated to detect diethyl ether with high selectivity via a method of utilizing one 440 nm bandpass filter. The as-prepared DFNST hybrids not only keep the excellent dendritic fibrous morphology but also bear ca. 21 wt% catalytic titanium oxide of anatase crystalline structure. The DFNST-based sensor exhibits extremely strong CTL emission at 440 nm toward diethyl ether against other VOCs like acetone, ethyl acetate, butanol, and so forth. The high response can be attributed to the unique architectural texture of DFNST. Under the optimum parameters, ether could be easily detected in a wide range from 2.0 to 40.0 mM with a fine detection limit of 1.55 mM (S/N = 3). Furthermore, the working life of this CTL sensor is satisfactory with outstanding stability and durability, far from damaging the morphology and activity of the DFNST sensing material. In conclusion, it is expected that this novel sensing material, the relevant CTL sensor, and the approach of employing the bandpass filter will be significant for the detection of diethyl ether in actual applications.

Dendritic fibrous nano-silica & titania (DFNST) nanospheres have been successfully prepared as the sensing materials for the detection of diethyl ether via a DFNST-based cataluminescence (CTL) sensor.