Adsorption of Methylene Blue and Pb2+ by using acid-activated Posidonia oceanica waste

Anionic Dye Removal with a Thin Cationic Polyaniline Coating on Cellulosic Biomaterial

This paper reports the development of novel adsorbent materials using polyaniline (PANI) grafted onto Posidonia (POS) fibers, aimed at efficiently removing phenol red (PSP), an anionic dye, from aqueous solutions. The synthesis involved the copolymerization of aniline grafted on the surface of the POS and aniline monomer in solution, resulting in a chemically bound thin PANI layer on the POS bioadsorbent. Structural characteristics and binding affinities of these adsorbents with PANI under its emeraldine salt (POS@PANI-ES) or emeraldine base (POS@PANI-EB) forms are reported. The rapid adsorption kinetics observed are attributed to enhanced accessibility to PANI adsorption sites on the POS surface. The binding percentages of PSP to POS@PANI-ES and POS@PANI-EB materials were found to be 97 and 50%, respectively, after 15 min of contact time. The Langmuir model for localized adsorption sites and the Volmer model for nonlocalized adsorption as a mobile layer were fitted to the experimental adsorption isotherms of PSP to POS@PANI-EB and POS@PANI-ES, yielding the thermodynamic parameters of adsorption. The adsorption capacities of PSP on POS@PANI-EB and POS@PANI-ES were 37.8 and 71.5 μmol g-1, respectively. The adsorption of PSP remained above 80% at moderate salt concentrations of around 0.1 mol L-1; however, higher concentrations of NaCl and CaCl2 in PSP solutions significantly reduced the adsorption on POS@PANI-ES.

Application of yellow phosphorus slag in resource recovery and environmental remediation: A review

Yellow phosphorus slag (YPS) is a byproduct in the production of yellow phosphorus, which contains several harmful components, such as phosphorus and fluorine. Approximately 8-12 tons of YPS are produced for each ton of yellow phosphorus. The accumulation of YPS causes serious environmental pollution problems with the development of the phosphorus industry. Various methods of utilizing YPS for high-value products and environmental remediation have been developed. The silicon, calcium and rare earth metals (REMs) contained in YPS can be extracted to produce high-value products. YPS, as an environmental remediation material, is generally used in wastewater treatment, soil remediation and carbon capture and utilization and is a promising method for solid waste treatment. This paper describes the physical and chemical properties of YPS. The recovery methods and mechanisms of waste heat, silicon, calcium and REMs in YPS are summarized and evaluated, and the application of YPS as an environmental remediation material is also described. Moreover, the currently existing problems of YPS treatment are discussed, and some suggestions for future research are provided.

Activation of Peroxymonosulfate with ZIF-67-derived Co/N-doped Porous Carbon Nanocubes for the Degradation of Congo Red Dye.. [DOI: 10.21203/rs.3.rs-3174583/v1] [Citation(s) in RCA: 0] [Impact Index Per Article: 0]

In this study, porous carbon nanaocubes encapsulated magnetic metallic Co nanoparticles (denoted as Co@N-PCNC) was prepared via pyrolyzing ZIF-67 nanocubes precursor at 600°C, and characterized by various technologies. It was used to activate peroxymonosulfate (PMS) to degrade Congo red (CR) dye efficiently. Over 98.45% of 50 mg/L CR with initial pH of 5.5 was degraded by 100 mg/L PMS activated by 10 mg/L Co@N-C within 12 min. The free radical quenching experiments were performed to reveal the nature of the reactive oxygen species radicals generated throughout the catalytic oxidation of CR. The effects of common inorganic anions and water matrix on CR removal were studied. The Co@N-PCNC displayed good operational stability, and after three cycles, the CR removal rate can still maintain over 90% after 12 min reaction.

Sustainable Exploitation of Posidonia oceanica Sea Balls (Egagropili): A Review

Posidonia oceanica (L.) Delile is the main seagrass plant in the Mediterranean basin that forms huge underwater meadows. Its leaves, when decomposed, are transported to the coasts, where they create huge banquettes that protect the beaches from sea erosion. Its roots and rhizome fragments, instead, aggregate into fibrous sea balls, called egagropili, that are shaped and accumulated by the waves along the shoreline. Their presence on the beach is generally disliked by tourists, and, thus, local communities commonly treat them as waste to remove and discard. Posidonia oceanica egagropili might represent a vegetable lignocellulose biomass to be valorized as a renewable substrate to produce added value molecules in biotechnological processes, as bio-absorbents in environmental decontamination, to prepare new bioplastics and biocomposites, or as insulating and reinforcement materials for construction and building. In this review, the structural characteristics, and the biological role of Posidonia oceanica egagropili are described, as well as their applications in different fields as reported in scientific papers published in recent years.

Synthesis and characterization of calcium and magnesium based oxides and titanates for photocatalytic degradation of rhodamine B: a comparative study

The current investigation deals with the simple and ecological synthesis of CaO, MgO, CaTiO_3, and MgTiO₃ for the photocatalytic dilapidation of rhodamine B dye. CaO was procured from chicken eggshell waste by calcination process, while MgO was produced by solution combustion method using urea as a fuel source. Furthermore, CaTiO₃ and MgTiO₃ were synthesized through an easy and simple solid-state method by mixing thoroughly the synthesized CaO or MgO with TiO₂ before calcination at 900 °C. XRD and EDX investigations confirmed the phase formation of the materials. Moreover, FTIR spectra revealed the existence of Ca-Ti-O, Mg-Ti-O, and Ti-O which resembles the chemical composition of the proposed materials. SEM micrographs revealed that the surface of CaTiO₃ is rougher with relatively dispersed particles compared to MgTiO₃, reflecting a higher surface area of CaTiO₃. Diffuse reflectance spectroscopy investigations indicated that the synthesized materials can act as photocatalysts under UV illumination. Accordingly, CaO and CaTiO₃ effectively degraded rhodamine B dye within 120 min with a photodegradation activity of 63% and 72%, respectively. In contrast, the photocatalytic degradation activity of MgO and MgTiO₃ was much lower, since only 21.39 and 29.44% of the dye were degraded, respectively after 120 min of irradiation. Furtheremore, the photocatalytic activity of the mixture from both Ca and Mg titanates was 64.63%. These findings might be valuable for designing potential and affordable photocatalysts for wastewater purification.

Occurrence and seasonal variation of plasticizers in sediments and biota from the coast of Mahdia, Tunisia

Plasticizers are compounds often involved in the manufacturing of plastic products. Nevertheless, the ageing of the latter generates plasticizers that generally end up in the marine environment. In fact, marine pollution by phthalate acid esters (PAEs) and their alternatives has become an environmental and health issue of serious concern, as they are largely and ubiquitously present in the environment and aquatic organisms. In the present study, four PAEs, such as diethyl phthalate (DEP), diisobutyl phthalate (DiBP), dibutyl phthalate (DBP), and di(2-ethylhexyl) phthalate (DEHP), and one non-phthalate plasticizer (NPP), namely di-2-ethylhexyl terephthalate (DEHT), are wanted in different marine compartments from the coast of Mahdia in Tunisia such as sediment, seagrass, and mussel. The most abundant and frequently detected congener was DEHT at the concentrations reached 1.181 mg/kg in the sediment, 1.121 mg/kg in the seagrass, and 1.86 mg/kg in the mussel. This result indicates that the DEHT could emerge through the food chain and therefore bioaccumulate in marine compartments. In addition, we noticed that the seasonal variations of plasticizers were seriously affected by environmental factors including industrial and urban discharges.

Photocatalytic degradation of dyes by novel electrospun nanofibers: A review

Textile industry is a significant contributor of wastewater, which contains pollutants including dye and other chemical substances. The release of thousands of tons of dye used in textile processing and finishing into natural streams and aquatic bodies present dire harm to the environment. In response to environmental concerns, a number of research have been done using low-cost technology to produce absorbents that can remove dyes from water bodies. Distinct techniques such as adsorption, enzymatic and photocatalytic degradation, etc. have been employed to remove dyes. In the last few decades, photocatalysis, a simple and green strategy, has emerged as the most valuable and recent principle that deals with wastewater treatment, using uniquely fabricated nanomaterials. Among them, rapid and versatile electrospinning methods have been used for the construction of a large surface area, hierarchical and reusable nanofibers for environmental remediation. As a flexible and fast fabrication method, reviewing the use of electrospun photocatalytic nanofibers, influential parameters in electrospinning and their effectiveness in the generation of oxidizing agents are a promising platform for the fabrication of novel nanomaterials in photocatalytic degradation of dyes. This review discusses techniques for dye removal, electrospun nanofibers, their fabrication and application in photocatalysis; mechanism of photocatalytic degradation, and challenges and suggested remedies for electrospun nanofibers in photocatalysis.

A New Insight into the Mechanisms Underlying the Discoloration, Sorption, and Photodegradation of Methylene Blue Solutions with and without BNOx Nanocatalysts

Methylene blue (MB) is widely used as a test material in photodynamic therapy and photocatalysis. These applications require an accurate determination of the MB concentration as well as the factors affecting the temporal evolution of the MB concentration. Optical absorbance is the most common method used to estimate MB concentration. This paper presents a detailed study of the dependence of the optical absorbance of aqueous methylene blue (MB) solutions in a concentration range of 0.5 to 10 mg·L^-1. The nonlinear behavior of optical absorbance as a function of MB concentration is described for the first time. A sharp change in optical absorption is observed in the range of MB concentrations from 3.33 to 4.00 mg·L^-1. Based on the analysis of the absorption spectra, it is concluded that this is due to the formation of MB dimers and trimers in the specific concentration range. For the first time, a strong, thermally induced discoloration effect of the MB solution under the influence of visible and sunlight was revealed: the simultaneous illumination and heating of MB solutions from 20 to 80 °C leads to a twofold decrease in the MB concentration in the solution. Exposure to sunlight for 120 min at a temperature of 80 °C led to the discoloration of the MB solution by more than 80%. The thermally induced discoloration of MB solutions should be considered in photocatalytic experiments when tested solutions are not thermally stabilized and heated due to irradiation. We discuss whether MB is a suitable test material for photocatalytic experiments and consider this using the example of a new photocatalytic material-boron oxynitride (BNO_x) nanoparticles-with 4.2 and 6.5 at.% of oxygen. It is shown that discoloration is a complex process and includes the following mechanisms: thermally induced MB photodegradation, MB absorption on BNO_x NPs, self-sensitizing MB photooxidation, and photocatalytic MB degradation. Careful consideration of all these processes makes it possible to determine the photocatalytic contribution to the discoloration process when using MB as a test material. The photocatalytic activity of BNO_x NPs containing 4.2 and 6.5 at.% of oxygen, estimated at ~440 μmol·g^-1·h^-1. The obtained results are discussed based on the results of DFT calculations considering the effect of MB sorption on its self-sensitizing photooxidation activity. A DFT analysis of the MB sorption capacity with BNO_x NPs shows that surface oxygen defects prevent the sorption of MB molecules due to their planar orientation over the BNO_x surface. To enhance the sorption capacity, surface oxygen defects should be eliminated.

Low-cost Posidonia oceanica bio-adsorbent for efficient removal of antibiotic oxytetracycline from water

The presence of antibiotics as micro-contaminants in the water and aqueous environments is a health concern to humans and the ecosystem. Therefore, their elimination by adsorption to available and cheap materials in water treatment plants is a research topic of high relevance. The present paper reports on the adsorption behavior of oxytetracycline on a bio-adsorbent prepared from Posidonia oceanica; an abundant Mediterranean biomass. Characterization of the pretreated Posidonia biomaterial was achieved using several analyses such as Boehm acid-base titration method, pH_PZC determination, and analysis techniques (FTIR, ¹³C CP-MAS NMR, optical microscopy, and TGA). The pH_PZC occurred around pH 2.11. Posidonia biomaterial showed a fast and high uptake rate throughout the adsorption process, which is a definite advantage for analytical applications such as water decontamination. The experimental kinetic data fitted very rightly the pseudo-second-order kinetic model and the equilibrium uptake can adopt the bi-Langmuir isotherm model for all studied pH values which assumes adsorptions at the two localized sites. Maximum adsorption capacities of 11.8 mg∙g^-1 and 4.4 mg∙g^-1 for the two adsorption sites are reached at pH 6. The oxytetracycline adsorption process onto Posidonia bio-adsorbent is spontaneous (Δ_adsG⁰ < 0), exothermic (Δ_adsH⁰ < 0), and entropically favorable (Δ_adsS⁰ > 0). The effect of pH on adsorption behavior and the thermodynamic parameters of adsorption are consistent with a possible origin of adsorption of oxytetracycline by means of hydrogen bonding interactions between surface hydroxyl and phenolic groups of the biomaterial and oxytetracycline. The proposed green and environmentally friendly biomaterial offers potential benefits as a bio-adsorbent in the remediation of aquatic environments contaminated by various organic materials.

Activated carbon derived from sugarcane and modified with natural zeolite for efficient adsorption of methylene blue dye: experimentally and theoretically approaches

The introduction of activated carbon/natural zeolite (AC/NZ) as an efficient and reliable nanoadsorbent for enhancing methylene blue (MB) dye adsorption. By calcining sugarcane waste at various temperatures between 500 and 900 °C, activated carbons (ACs) are formed. Both XRD and SEM were used for the characterization of the prepared adsorbents. Adsorption measurements for the removal of MB dye were made on the impact of pH, beginning MB concentration, and contact time. The maximum AC500/NZ adsorption capacity for MB dye at 25 °C, pH 7, and an AC500/NZ mass of 50 mg was found to be approximately 51 mg/g at an initial concentration of 30 ppm. The pseudo-second-order kinetics model and the Temkin isotherm model describe the adsorption process. The Temkin model shows that the adsorption energy is 1.0 kcal/mol, indicating that the MB-to-AC500/NZ adsorption process occurs physically. Our Monte Carlo (MC) simulation studies supported our findings and showed that the Van der Waals dispersion force was responsible for the MB molecule's physical adsorption. The AC500/NZ adsorbent is thought to be a strong contender for water remediation.

Potential Use of Low-Cost Agri-Food Waste as Biosorbents for the Removal of Cd(II), Co(II), Ni(II) and Pb(II) from Aqueous Solutions

We evaluated the potential use of agri-food waste for the removal of heavy metal ions from aqueous solutions and its application in different processes (e.g., water remediation, in the production of biomass enriched in nutritionally significant elements, etc.). Biomasses from grape seed, grape pomace, loquat seed, Calabrese broccoli stem, empty pods of carob and broad bean pods, unripe bitter orange peel, kumquat, orange pulp and Canary Island banana pulp were prepared. The percentages and biosorption capacities were evaluated and compared with those refe-renced using Valencia orange peel (Citrus sinensis Valencia late). These studies allow for easily providing added value to different agri-food wastes. The results show that the proposed biomasses were able to retain the studied metal ions and obtained different percentages, being in some cases above 90%. The highest values were obtained using broad bean pod (Pb(II) (91.5%), Cd(II) (61.7%), Co(II) (40.7%) and Ni(II) (39.7%)). Similar values were observed using grape seed, broccoli stem, carob pod and unripe bitter orange peel. Carob pod for biosorption of Cd(II) is also of great interest. These studies suggest that the agri-food residues evaluated can be applied to prepare effective biosorbents of divalent metal ions from aqueous solutions.

Removal of Fe2+ and Mn2+ from Polluted Groundwater by Insoluble Humic Acid/Tourmaline Composite Particles

Insoluble humic acid/tourmaline composite particles (IHA/TM) were prepared by combining inorganic tourmaline (TM) with the natural organic polymer humic acid (HA) and carbonizing them at 330 °C to study the removal characteristics and mechanism of Fe²⁺ and Mn²⁺. The results showed that the optimal ratio of TM to IHA is 2:3. When the temperature of the IHA/TM composite particles was 35 °C and the pH was 6, the adsorption of Fe²⁺ and Mn²⁺ by IHA/TM reached equilibrium at 240 min. The optimum dose of the adsorbent was 10 g/L, and the equilibrium adsorption capacities of Fe²⁺ and Mn²⁺ were 5.645 mg/g and 3.574 mg/g, respectively. The process of IHA/TM adsorption of Fe²⁺ and Mn²⁺ in water was spontaneous, endothermic and sustainable, and cooling was not conducive to adsorption. The pseudo-second order kinetic equation can well reflect the adsorption mechanism of IHA/TM on Fe²⁺ and Mn²⁺, and the Langmuir adsorption model better describes the isothermal adsorption behaviour. The material characterisation and adsorption experiments indicate that surface coordination and chemical precipitation are the main mechanisms of Fe²⁺ and Mn²⁺ removal by IHA/TM.

"Neptune Balls" Polysaccharides: Disentangling the Wiry Seagrass Detritus

Each year, high amounts of dead seagrass material are washed ashore at beaches world-wide. In the Mediterranean region, the seagrass Posidonia oceanica is responsible for huge agglomerates of ball-like seagrass litter. As these are often removed due to touristic reasons, a reuse method would be a step towards a more ecologically oriented society. In this study, the main polysaccharide components were analyzed, in order to propose possible usage options. To do this, different aqueous fractions were extracted, analyzed by classical carbohydrate analysis methods (GC-FID/MS, colorimetric assay and elemental analysis), and purified by ion-exchange chromatography, as well as selective precipitation with a detecting agent for highly glycosylated glycoproteins. The obtained purified fractions were analyzed in detail and a linkage-type analysis of the most promising extract was conducted via permethylation. Only low amounts of glycoproteins, as well as medium amounts of the characteristic apiogalacturonan were likely to be present, while xylan seemed to be the most abundant polysaccharide in most fractions. A partial structural proposal showed general accordance with land plant xylans, presenting reuse options in the field of biofuel and bioplastic generation.

Cellulose citrate: a convenient and reusable bio-adsorbent for effective removal of methylene blue dye from artificially contaminated water

In the present work, we proved the efficacy of cellulose citrate to remove methylene blue (MB) from artificially contaminated water. MB is a widely used dye, but because of its chemical aromatic structure, it is significantly stable with quite slow biodegradation, causing consequent serious health problems for people and significant environmental pollution. Cellulose citrate, the bio-adsorbent proposed and studied by us to remediate water polluted by MB, is produced by a green, cheap and fast procedure that makes use of two abundant natural products, cellulose and citric acid. The average of two citrate groups for each glucose unit of cellulose chains allows this material to have many carboxylic groups available for interaction with the cationic dye. The characterization was carried out through FT-IR, SEM, specific surface area, pore structure parameters and zeta potential. The negative value of the zeta potential at neutral pH is consistent with the affinity of this material for the adsorption of cationic compounds like MB. The activity of the adsorbent at different times, temperatures, pH and concentrations was investigated. The process followed monolayer adsorption typical of the Langmuir model, with a maximum adsorption capacity of 96.2 mg g-1, while for the kinetic studies the process followed a pseudo-second order model. The highest levels of adsorption were reported using solutions of dye with concentrations under 100 mg L-1. The adsorbent can be regenerated several times without a significant loss in the adsorption capacity, and it is not strongly affected by temperature and pH, giving rise to a simple and eco-sustainable procedure for water remediation. Therefore, we conclude that cellulose citrate can be considered as a promising bio-adsorbent for the removal of MB and other cationic pollutants from the environment.

Polypyrrole functionalized Cobalt oxide Graphene (COPYGO) nanocomposite for the efficient removal of dyes and heavy metal pollutants from aqueous effluents

A cobalt oxide graphene nanocomposite functionalized with polypyrrole (COPYGO) having a heterogenous porous structure was synthesized using hydrothermal method. Microscopic imaging of the COPYGO surface revealed its highly porous and ordered features. The adsorption performance of the COPYGO composite was systemically investigated for Methylene Blue (MB), Congo red (CR) dyes and toxic lead (Pb(II)) and Cadmium (Cd(II)) metals. These were selected as they are the common pollutants in industrial wastewater. The COPYGO was found to be thermally stable up to 195 ^oC with a specific surface area of 133 m² g^-1. Experimental data indicates that the COPYGO follows Langmuir and Temkin adsorption isotherm. The COPYGO was efficient in removing MB (92.8%), CR (92.2%), Pb(II) (93.08%) and Cd(II) (95.28%) pollutants at pH 7.2, 5.0, 5.5 and 6.1 respectively from the simulated effluents. The maximum adsorption capacity (Q_max) observed for MB 663.018 mg g^-1, CR 659.056 mg g^-1, Pb(II) 780.363 mg g^-1 and Cd(II) 794.188 mg g^-1 pollutants. The thermodynamic analysis of the COPYGO indicates that the adsorption is endothermic and spontaneous in nature. COPYGO showed very high efficient removal rate for the pollutants in simulated effluents which guaranteed its benefits and efficacy in industrial wastewater treatment.

Optimizing the Biosorption Behavior of Ludwigia stolonifera in the Removal of Lead and Chromium Metal Ions from Synthetic Wastewater

In this study, a natural low-coast, efficient, and eco- bio-sorbent plant material (Ludwigia stolonifera), with both parts of the root and shoot, were studied for the removal of the cationic metal ions, lead Pb2+ and chromium Cr6+, via batch mode experiments to evaluate their maximum adsorption capacity, and held a comparison between the used bio-sorbent roots and shoots, based on the highest bio-sorption potential. Optimization of the bio-sorption parameters, such as contact time, pH, bio-sorbent (root and shoot) dosage, and initial ion concentration was conducted. The results indicated that 1.6 g of the used bio-sorbent shoot material removed 81.4% of Pb2+, and 77% of Cr6+ metal ions from liquid media under the conditions of 100 ppm of initial metal ions concentration at room temperature for 60 min of contact time with the static condition. Different isotherms and kinetic models were fit to the experimental data to understand the nature of the bio-sorption process. The experimental data were best fit by the pseudo-second-order kinetic model with a high correlation coefficient (R2 = 0.999), which reveals the chemisorption nature of the bio-sorption process. The chemical and structural analysis of the used bio-sorbent, before and after Cr6+ and Pb2+ bio-sorption, were performed using different techniques of characterization, such as Scanning Electron Microscopy (SEM) and Fourier-transform infrared spectroscopy (FTIR). The used bio-sorbent proved to be a low-cost, efficient, and eco-friendly material to remove heavy metal ions from aqueous solutions.

Monitoring of methylene blue monomers and dimers to control the bacterialogical water quality including application to photocatalysis

In this study, we propose the development of a rapid and reliable method to control and to monitor microbial water quality. The methylene blue (MB) decolorization assay was based on the analysis of spectral profiles of dye in interaction with a different bacterial concentration. The determination of dye decolorization rate (DDR) shows a correlation between the MB reduction rate and the bacterial density. Moreover, the kinetic of the monomer and dimer equilibrium of MB in water mainly, the monitoring of bounded MB species in relationship with a knowed concentration of target bacteria, was allowed to establish a relationship between MB decolorization rate and bacterial density. Furthermore, this method was applied to evaluate the water quality after photocatalysis. Based on this method, the photocatalytic effects on bacterial density was highlighted by the decrease in DDR after photocatalytic treatment with fractioned times (0 to 5 h); this increase was followed by a decrease of bounded MB species and, an increase in free MB forms miming the reduction of bacterial density due to the biocide effects of photocatalysis process. However, the analysis of spectra profiles shows a weak but a continuous decrease in bounded MB dimer and monomer forms in the treated water samples exempt of culturable bacteria. Moreover, the MB spectra profiles were tended toward a negative control spectrum without superposition. Thus, the possibility of the presence of viable but non-culturable bacteria was expected; therefore, to optimize this tertiary water treatment process, an extending on proceeding time was recommended to avoid the bacterial resuscitation after photocatalysis.

Increasing straw surface functionalities for enhanced adsorption property

A simple low-temperature partial-oxidation process was demonstrated as an effective technology for reed straw modification towards environmental remediation. At an optimal temperature of 180 °C, the straw materials exhibited a remarkable colour change from light yellow to dark brown, increased methylene blue (MB) uptake by 1.8 times, enhanced removal efficiency from 34.5% to 92.8%, and a high yield of 77.2%. Spectroscopic characterization and Boehm titration proved that the amount of surface oxygen (O)-containing functional groups significantly increased after modification. A strong linear correlation (R² = 0.93) existed between total amounts of O-containing functional groups and MB uptake for modification temperatures below 180 °C, whereas blockage of the pore entrances and competition with metallic cations must be taken into account for samples generated from excess heating (>180 °C). These results provided insights into designing promising technologies for sustainable environmental management through reutilization of agricultural waste.

Iminodiacetic acid functionalized magnetic peanut husk for the removal of methylene blue from solution: characterization and equilibrium studies

A novel adsorbent PN-Fe₃O₄-IDA was developed by the chemical modification of magnetic peanut husk with iminodiacetic acid (IDA) and its efficacy for the sequestration of cationic dyes assessed using methylene blue (MB) as a model. This modification process enhanced the adsorption capacity of peanut husk as an adsorbent for dye sequestration and at the same time greatly minimized the adverse effects associated with its use in the pristine state. Results from the batch adsorption studies indicated that the uptake of MB onto PN-Fe₃O₄-IDA increased with MB concentration, contact time, temperature and pH whereas it decreased in the presence of some common salts. The pseudo-second-order kinetic model was observed to best describe the adsorption process which may greatly be influenced by the intra particle diffusion mass transfer. A maximum monolayer adsorption capacity of 43.5 mg g^-1 was observed at 313 K according to the Langmuir model. There was good property of regeneration for MB-loaded PN-Fe₃O₄-IDA. Based on these results, as well as other unique features such as easy separation and preparation under benign environmental conditions, PN-Fe₃O₄-IDA exhibits great potential for the removal of MB and other cationic pollutants in practical applications with easy separation from solution using external magnet. Graphical abstract.

Treatment of Yellow Phosphorus Slag and Reuse of It as an Absorbent of Chromium (VI) Ions and Methylene Blue

Yellow phosphorus is used widely in the world for production of phosphoric acid, various phosphates, flame retardant, detergent, water treatment, metal surface treatment, etc. After the production of yellow phosphorus, a large amount of phosphorus sludge is discharged to environment, causing environment pollution. This work focused on treatment of yellow phosphorus slag (YPS) and application of it as an absorbent for chromium (VI) ion and methylene blue. The YPS was first washed with water to remove phosphoferrite (FeP) and impurities and then being milled and transferred to a float sorting system to obtain YPS particles. The characteristics of YPS particles were determined by inductively coupled plasma-mass-spectrometry (ICP-MS), energy-dispersive X-ray spectroscopy (EDX), infrared spectroscopy (IR), scanning electron microscopy (SEM), X-ray diffraction (XRD), zeta potential, and nitrogen adsorption methods. The YPS particles were retreated with NaOH, HNO3, and EDTA solutions to evaluate the influence of these agents on metal ion and organic compound adsorption ability by YPS. The adsorption parameters of chromium (VI) ion and methylene blue (MB) by treated YPS particles were recognized by the ultraviolet-visible (UV-Vis) spectrometer. The effects of temperature, pH solution, and initial concentration of absorbed substances on the adsorption ability were investigated. The adsorption isotherms and adsorption kinetics of chromium (VI) ion and MB by YPS particles were also determined. The obtained results confirmed that the green technology used to treat the YPS2 particles is suitable to obtain an effective absorbent. The adsorption efficiency of YPS2 particles for removal of chromium (VI) ions is smaller than that for removal of MB in aqueous solutions. The adsorption isotherm of MB adsorption process is complied with the Langmuir isotherm while the adsorption kinetic fits well with the pseudo-second-order reaction model. The thermodynamic parameters of MB adsorption processed on YPS2 were calculated and discussed.

An Integrating Platform of Ratiometric Fluorescent Adsorbent for Unconventional Real-Time Removing and Monitoring of Copper Ions

Nondegradable heavy metals have caused great dangers to the environment and human health. Combining stimuli-responsive materials with conventional MOF-based adsorbents has been considered an effective method to generate intelligent adsorbents for superior control over the adsorption process. Herein, a smart MOF-based ratiometric fluorescent adsorbent was designed to accurately monitor the progression of the removal of copper ions with dual-emitting fluorescence signal. Unlike the traditional difunctional materials, this delicately designed platform overcomes the huge energy gap to achieve two functions simultaneously. This unconventional platform provides a reliable fluorescent response toward Cu²⁺ during the removing process, changing linearly related to the degree of the adsorption process, which holds extreme promise in effectively monitoring the adsorption process. The underlying relationship of the adsorption and fluorescence response process toward copper was investigated by density functional theory (DFT) calculations. In particular, because of the favorable ion binding affinity of ZIF-8 and self-calibrating effect of RhB, the as-prepared smart adsorbent demonstrates a superior adsorption performance of 608 mg g^-1, broad response range (0.05-200 ppm, 2.07 × 10^-7to 8.29 × 10^-4 M), ultrahigh sensitivity (0.04 ppm, 1.91 × 10^-7 M) toward Cu²⁺ and strong anti-interference ability. This smart adsorbent opens an intelligent pathway to promote substantial advancements in the fields of environmental monitoring and industrial waste management.

Green Reduction of Graphene Oxide using Kaffir Lime Peel Extract (Citrus hystrix) and Its Application as Adsorbent for Methylene Blue

Green reduction of graphene oxide (GO) by phytochemicals was explored using the aqueous extract of kaffir lime peels. The research methods included preparation of extracts, preparation of GO, preparation and characterization of reduced-GO (RGO) using Fourier Transform Infrared (FTIR), X-ray diffraction (XRD), and UV-Vis spectroscopy, as well as methylene blue (MB) adsorption test using RGO. The RGO characterization showed that GO was successfully reduced by a C=C group restoration. The MB adsorption kinetics profile in RGO is more suitable for the pseudo-second-order model, whereas for the adsorption isotherm it is more suitable for the Langmuir model with a maximum adsorption capacity (q_max) of 276.06 mg/g at room temperature. The best ratio of GO: kaffir lime peel extract used to prepare RGO was at a ratio of 1: 2. Based on the ΔG, ΔH, and ΔS values, the adsorption of RGO-MB was defined as spontaneous and endothermic process. The results promise the potential application of RGO derived via green route to remove cationic dye in wastewater.