Apparent Contact Angle around the Periphery of a Liquid Drop on Roughened Surfaces

Cytocompatibility of electrospun poly-L-lactic acid membranes for Bruch's membrane regeneration using human embryonic stem cell-derived retinal pigment epithelial cells

Cell replacement therapy is under development for dry age-related macular degeneration (AMD). A thin membrane resembling the Bruch's membrane is required to form a cell-on-membrane construct with retinal pigment epithelial (RPE) cells. These cells have been differentiated from human embryonic stem cells (hESCs) in vitro. A carrier membrane is required for cell implantation, which is biocompatible for cell growth and has dimensions and physical properties resembling the Bruch's membrane. Here a nanofiber electrospun poly-L-lactic acid (PLLA) membrane is tested for capacity to support cell growth and maturation. The requirements for laminin coating of the membrane are identified here. A porous electrospun nanofibrous PLLA membrane of ∼50 nm fiber diameter was developed as a prototype support for functional RPE cells grown as a monolayer. The need for laminin coating applied to the membrane following treatment with poly-L-ornithine (PLO), was identified in terms of cell growth and survival. Test membranes were compared in terms of hydrophilicity after laminin coating, mechanical properties of surface roughness and Young's modulus, porosity and ability to promote the attachment and proliferation of hESC-RPE cells in culture for up to 8 weeks. Over this time, RPE cell proliferation, morphology, and marker and gene expression, were monitored. The functional capacity of cell monolayers was identified in terms of transepithelial electrical resistance (TEER), phagocytosis of cells, as well as expression of the cytokines, vascular endothelial growth factor (VEGF) and pigment epithelium-derived factor (PEDF). PLLA polymer fibers are naturally hydrophobic, so their hydrophilicity was improved by pretreatment with PLO for subsequent coating with the bioactive protein laminin. They were then assessed for amount of laminin adsorbed, contact angle and uniformity of coating using scanning electron microscopy (SEM). Pretreatment with 100% PLO gave the best result over 10% PLO treatment or no treatment prior to laminin adsorption with significantly greater surface stiffness and modulus. By 6 weeks after cell plating, the coated membranes could support a mature RPE monolayer showing a dense apical microvillus structure and pigmented 3D polygonal cell morphology. After 8 weeks, PLO (100%)-Lam coated membranes exhibited the highest cell number, cell proliferation, and RPE barrier function measured as TEER. RPE cells showed the higher levels of specific surface marker and gene expression. Microphthalmia-associated transcription factor expression was highly upregulated indicating maturation of cells. Functionality of cells was indicated by expression of VEGF and PEDF genes as well as phagocytic capacity. In conclusion, electrospun PLLA membranes coated with PLO-Lam have the physical and biological properties to support the distribution and migration of hESC-RPE cells throughout the whole structure. They represent a good membrane candidate for preparation of hESC-RPE cells as a monolayer for implantation into the subretinal space of AMD patients.

Dynamic Behavior of Viscous Droplets Impact on a Flexible Mesh Surface

The dynamic behavior of a viscous droplet impacting a flexible mesh surface with a fixed end is studied by high-speed photography in this work. Our experimental results reveal that surface vibration occurs when the viscous droplet impacts the flexible mesh surface. Simultaneously, the droplet spreads on the upper surface and penetrates into the mesh surface, resulting in a decrease in the spreading diameter on the upper surface. On the lower surface, the droplet elongates and forms multiple ligaments. Notably, different dynamic behaviors are observed when the droplet impacts surfaces with varying Weber (We) numbers due to viscous dissipation and surface vibration. However, as the impact position deviates from the fixed end, the surface vibrational amplitude increases, leading to a decreased diffusion range of the droplet on the lower surface. In addition, the vibration amplitude significantly enhances with increase of the We number. The vibration induces stretching and eventual rupture of the cardinal ligament under specific conditions. The first breaking time of the cardinal ligament delays with the decrease of the We number. As the impact position moves away from the fixed end, this situation is enhanced. Especially, when the stretching direction of the ligament is inconsistent with the vibration direction of the surface, the vibration has a great influence on the stretching behavior of the cardinal ligament.

On the role of surface morphology in impacting-freezing dynamics of supercooled droplets

A thorough understanding of droplet impact and freezing is vital in preventing ice accretion on many outdoor devices. This simulation-based study investigated the effect of surface morphology on the impacting-freezing process of a supercooled droplet. Also, the variations of Weber number and supercooling temperature were studied numerically. The droplet impact and freezing process were simulated with the volume of fluid method and freezing model. A more accurate simulation was achieved by modeling the supercooled droplet and the dynamic contact angle. At the given ranges of the input parameters, the main factors that guaranteed droplet rebounding after collision were determined. The supercooling temperature and the groove width should be above 266 K and less than 0.21 mm, respectively. The droplet should also maintain its cohesion and integrity during impact. Creating grooves on a surface is novel and paves a new way to understand the impact and solidification of water droplets in supercooled conditions.

Bioadhesive behaviors of HPMC E5: comparative analysis of various techniques, histological and human radiological evidence

Enhancing drug residence duration within the stomach offers distinct advantages for both localized and systemic effects. Numerous strategies have been proposed to extend drug residence time, with mucoadhesive polymers being a notable avenue. In this context, hydroxypropyl methylcellulose E5 has been employed as both a binding agent for granulating contrast metal powder and a mucoadhesive polymer, spanning various concentrations. The in vitro bioadhesion strength of the formulated tablets was gauged against the stomach lining of rabbits, for the quantification of bioadhesive forces. The temporal aspect of bioadhesion was evaluated through two approaches: one centered on gastric fluid dynamics and another proffered by the researchers, focusing on gastric wall kinetics. The results divulged a decline in bioadhesion force concomitant with high polymer concentrations. Histological examination of stained stomach sections revealed mucosal perturbations within the rabbit stomach. These disruptions exhibited an escalating trend in conjunction with elevated polymer concentrations, culminating in extensive disturbance at a 7.5% polymer concentration. The outcomes unveiled a direct relationship between polymer concentration increments and extended contact time. Subsequent radiological tracking of contrast metal behavior within a mature human stomach indicated a residence time of 6 h due to the entrapment of displaced components at disparate locations.

PIP2 Alteration Caused by Elastic Modulus and Tropism of Electrospun Scaffolds Facilitates Altered BMSCs Proliferation and Differentiation

Aligned submicron fibers have played an essential role in inducing stem cell proliferation and differentiation. In this study, it is aimed to identify the differential causes of stem cell proliferation and differentiation between bone marrow mesenchymal stem cells (BMSCs) on aligned-random fibers with different elastic modulus, and to change the differential levels through a regulatory mechanism mediated by B-cell lymphoma 6 protein(BCL-6) and miRNA-126-5p(miR-126-5p). The results showed that phosphatidylinositol(4,5)bisphosphate alterations are found in the aligned fibers compared with the random fibers, which has a regular and oriented structure, excellent cytocompatibility, regular cytoskeleton, and high differentiation potential. The same trend is actual for the aligned fibers with a lower elastic modulus. The level of proliferative differentiation genes in cells is altered by BCL-6 and miR-126-5p mediated regulatory mechanisms to make the cell distribution nearly consistent with the cell state on low elastic modulus aligned fibers. This work demonstrates the reason for the difference of cells between the two kinds of fibers and on fibers with different elastic modulus. These findings provide more insights for understanding the gene-level regulation of cell growth in tissue engineering.

Formation of Oxide Layer and Wettability on the Surface of Electrical Discharge Machining-Based Implant Engineered by Micro-Finishing

The ability to promote rapid osseointegration is an important criterion on the titanium implant surface. This performance is greatly determined by the roughness, wettability, and composition of the implant surface. This study aims to investigate the oxide layer formation and wettability on the EDM-titanium implant surface engineered by different micro-finishing methods (i.e. mechanical, physical, and chemical processes). The oxide layer formation was investigated by observing the wt% of oxygen formed while the wettability criterion was studied by determining the contact angle between the liquid and solid surface. The result reveals that the oxide layers formed on the sample surface, excepting Sulfuric acid (H2SO4) 95%-etched, show an interaction with the surface roughness and its wettability. The smoother the surface roughness of the sample, the lower the percentage of the oxide layer and the contact angle formed on the sample surface. In this aspect, the ultrasonic cleaning benchmark has the highest percentage by altering 18.84% of the oxide layer formed by the EDM process while the decrease of 75.89% generated by the H2SO4-etching is the lowest one. On the other hand, the higher the percentage of the oxide layer formation, the lower the wettability of the sample surface. In this aspect, the ultrasonic cleaning benchmark has the lowest wettability with a contact angle of 124º (hydrophilic) while HCl-etching is the lowest with 45º (hydrophobic). The results are notable that the ultrasonic cleaning method is able to alter wt% of the oxygen on the EDM-titanium implant surface, whereas the acid etching method can be recommended as a worthy method of the surface finishing for the semi-permanent type of implant.

Evaluation of Viscosity Dependence of the Critical Meniscus Height with Optical Fiber Sensors

Conventional means of data extraction using optical fiber interrogators are not adequate for fast-paced detection of a target parameter. In this instance, the relationship between the critical meniscus heights (CMH) of several liquids to the extraction speed of a rod submerged in them, have been analyzed. A limitation of a previous interrogator used for the purpose had been light absorption by the liquid due to the used bandwidth of the readily-available light source, i.e., C-band. The newly proposed technique addresses this limitation by utilizing a broadband light source instead, with a Si-photodetector and an Arduino. In addition, the Arduino is capable of extracting data at a relatively faster rate with respect to the conventional optical interrogator. The use of a different operational wavelength (850 nm instead of 1550 nm) increased the r² and the sensitivity of the sensor. The new setup can measure surface chemistry properties, with the advantage of being comparatively cheaper than the conventionally available interrogator units, thereby providing a suitable alternative to conventional measurement techniques of liquid surface properties, while reducing material waste, i.e., in terms of the required volume for detection of a target parameter, through the use of optical fiber.

Past and Current Progress in the Development of Antiviral/Antimicrobial Polymer Coating towards COVID-19 Prevention: A Review

The astonishing outbreak of SARS-CoV-2 coronavirus, known as COVID-19, has attracted numerous research interests, particularly regarding fabricating antimicrobial surface coatings. This initiative is aimed at overcoming and minimizing viral and bacterial transmission to the human. When contaminated droplets from an infected individual land onto common surfaces, SARS-CoV-2 coronavirus is able to survive on various surfaces for up to 9 days. Thus, the possibility of virus transmission increases after touching or being in contact with contaminated surfaces. Herein, we aim to provide overviews of various types of antiviral and antimicrobial coating agents, such as antimicrobial polymer-based coating, metal-based coating, functional nanomaterial, and nanocomposite-based coating. The action mode for each type of antimicrobial agent against pathogens is elaborated. In addition, surface properties of the designed antiviral and antimicrobial polymer coating with their influencing factors are discussed in this review. This paper also exhibits several techniques on surface modification to improve surface properties. Various developed research on the development of antiviral/antimicrobial polymer coating to curb the COVID-19 pandemic are also presented in this review.

Role of physicochemical properties of some grades of hydroxypropyl methylcellulose on in vitro mucoadhesion

Relationships between physicochemical properties of hydroxypropyl methylcellulose (HPMC) compacts and their in vitro mucoadhesive performances were investigated in this study. Some commercial grades of HPMC (K3, E3, E5, E50, K4M, E4M and K15M) were prepared into compacts, and their surface hydrophilicity and hydration behavior were characterized. The in vitro mucoadhesive performance was determined by the tensile strength between the compacts and different regions of mucosal membrane (buccal, sublingual, stomach, and intestine). Positive correlations were found between: (1) viscosity of HPMC compacts and contact angle in different simulated body fluids; (2) viscosity of HPMC compacts and in vitro mucoadhesive force; (3) contact angle and in vitro mucoadhesive force. The hydration increased with an increase in viscosity of HPMC compacts. The polar lipid content in mucosa was found to be an important factor affecting the mucoadhesion. Lower polar lipid amount in the mucosal membrane promoted the rate of mucoadhesive force with the increasing viscosity of HPMC. The mucoadhesive mechanism of various grades of HPMC compacts were studied using the thermodynamic analysis of Lifschitz-van der Waals (LW) interaction and Lewis acid-base (AB) interactions. The total free energy of adhesion (ΔG^TOT) provided a prediction of an overall tendency of mucoadhesion, and deviated from the measured mucoadhesive force.

Water on hydroxylated silica surfaces: Work of adhesion, interfacial entropy, and droplet wetting

In the last few years, much attention has been devoted to the control of the wettability properties of surfaces modified with functional groups. Molecular dynamics (MD) simulation is one of the powerful tools for microscopic analysis providing visual images and mean geometrical shapes of the contact line, e.g., of nanoscale droplets on solid surfaces, while profound understanding of wetting demands quantitative evaluation of the solid-liquid (SL) interfacial tension. In the present work, we examined the wetting of water on neutral and regular hydroxylated silica surfaces with five different area densities of OH groups ρ_A ^OH, ranging from a non-hydroxylated surface to a fully hydroxylated one through two theoretical methods: thermodynamic integration (TI) and MD simulations of quasi-two-dimensional equilibrium droplets. For the former, the work of adhesion needed to quasi-statically strip the water film off the solid surface was computed by the phantom wall TI scheme to evaluate the SL interfacial free energy, whereas for the latter, the apparent contact angle θ_app was calculated from the droplet density distribution. The theoretical contact angle θ_YD and the apparent one θ_app, both indicating the enhancement of wettability by an increase in ρ_A ^OH, presented good quantitative agreement, especially for non-hydroxylated and highly hydroxylated surfaces. On partially hydroxylated surfaces, in which θ_YD and θ_app slightly deviated, the Brownian motion of the droplet was suppressed, possibly due to the pinning of the contact line around the hydroxyl groups. Relations between work of adhesion, interfacial energy, and entropy loss were also analyzed, and their influence on the wettability was discussed.

Effects of titanium with different micro/nano structures on the ability of osteoblasts to resist oxidative stress

Excessive accumulation of oxidative intermediates in the elderly significantly aggravates bone degradation and hinders the osseointegration of topological titanium (Ti) implants. Thus, it is of great significance to evaluate the antioxidant and osteoinduction capabilities of various nano, micro or micro/nano-composite structures under oxidative stress (OS) microenvironment. In this study, we discovered that 110 nm titania nanotubes (TNTs) enhanced the adsorption of fibronectin (FN) proteins onto smooth and rough titanium surfaces to varying degrees. Compared with Ti and 30 nm TNTs (T₃₀) groups, cells on 110 nm TNTs (T₁₁₀), microstructure/30 nm TNTs (M₃₀) and microstructure/110 nm TNTs (M₁₁₀) had smaller area, lower reactive oxygen species (ROS), and better proliferation/osteogenic differentiation abilities under OS condition, but there was no significant difference among the three groups. In addition, combined with our previous study, we suggested that T₁₁₀, M₃₀ and M₁₁₀ resistance to OS was also strongly associated with the high expression of FN-receptor integrin α5 or β1. All the findings indicated that the micro/nano-composed structures (M₃₀ & M₁₁₀) had similar anti-oxidation and osteogenesis abilities to T₁₁₀, which provided guidance for the application of different titanium implants with different topologies in the elderly.

Dependency of Contact Angles on Three-Phase Contact Line: A Review

The wetted area of a sessile droplet on a practical substrate is limited by the three-phase contact line and characterized by contact angle, contact radius and drop height. Although, contact angles of droplets have been studied for more than two hundred years, there are still some unanswered questions. In the last two decades, it was experimentally proven that the advancing and receding contact angles, and the contact angle hysteresis of rough and chemically heterogeneous surfaces, are determined by interactions of the liquid and the solid at the three-phase contact line alone, and the interfacial area within the contact perimeter is irrelevant. However, confusion and misunderstanding still exist in this field regarding the relationship between contact angle and surface roughness and chemical heterogeneity. An extensive review was published on the debate for the dependence of apparent contact angles on drop contact area or the three-phase contact line in 2014. Following this old review, several new articles were published on the same subject. This article presents a review of the novel articles (mostly published after 2014 to present) on the dependency of contact angles on the three-phase contact line, after a short summary is given for this long-lasting debate. Recently, some improvements have been made; for example, a relationship of the apparent contact angle with the properties of the three-phase line was obtained by replacing the solid–vapor interfacial tension term, γSV, with a string tension term containing the edge energy, γSLV, and curvature of the triple contact line, km, terms. In addition, a novel Gibbsian thermodynamics composite system was developed for a liquid drop resting on a heterogeneous multiphase and also on a homogeneous rough solid substrate at equilibrium conditions, and this approach led to the same conclusions given above. Moreover, some publications on the line energy concept along the three-phase contact line, and on the “modified” Cassie equations were also examined in this review.