Adsorption of methylene blue onto electrospun nanofibrous membranes of polylactic acid and polyacrylonitrile coated with chloride doped polyaniline

Tailoring electrospun nanocomposite fibers of polylactic acid for seamless methylene blue dye adsorption applications

The introduction of biopolymers, which are sustainable and green materials, desegregated nature's water purification proficiency with science and technology, opens a new sustainable methodology in water reclamation. In order to introduce an efficacious adsorbent system for MB dye-toxic pollutant, adsorption, providing robust mechanical properties and facile processability, a facile system was introduced via electrospinning utilizing polylactic acid (PLA) and Ti3C2Tx, viz., PMX. The addition of 3 wt.% Ti3C2Tx led to a 3-fold substantial augmentation in the uptake capacity of the membrane from 197.28 to 307 mg/g when the adsorbate concentration was 100 ppm. The adsorption followed a PSO behavior, proposing that the rate-limiting stage is chemisorption and data best fitted to Freundlich isotherm, indicating heterogeneous adsorption sites and multi-layer adsorption. Further, biodegradability was studied by simulating natural environmental conditions where the nanofibers exhibited 42-64% degradation after 270 days. Based on the result with PLA, it is anticipated that the prepared fibrous system will introduce a new perspective as a potential candidate for MB removal from wastewater, opening new directions toward the research and development in wastewater treatment with electrospun biopolymer fibers using waste PLA.

Emerging environmentally friendly bio-based nanocomposites for the efficient removal of dyes and micropollutants from wastewater by adsorption: a comprehensive review

Water scarcity will worsen due to population growth, urbanization, and climate change. Addressing this issue requires developing energy-efficient and cost-effective water purification technologies. One approach is to use biomass to make bio-based materials (BBMs) with valuable attributes. This aligns with the goal of environmental conservation and waste management. Furthermore, the use of biomass is advantageous because it is readily available, economical, and has minimal secondary environmental impact. Biomass materials are ideal for water purification because they are abundant and contain important functional groups like hydroxyl, carboxyl, and amino groups. Functional groups are important for modifying and absorbing contaminants in water. Single-sourced biomass has limitations such as weak mechanical strength, limited adsorption capacity, and chemical instability. Investing in research and development is crucial for the development of efficient methods to produce BBMs and establish suitable water purification application models. This review covers BBM production, modification, functionalization, and their applications in wastewater treatment. These applications include oil-water separation, membrane filtration, micropollutant removal, and organic pollutant elimination. This review explores the production processes and properties of BBMs from biopolymers, highlighting their potential for water treatment applications. Furthermore, this review discusses the future prospects and challenges of developing BBMs for water treatment and usage. Finally, this review highlights the importance of BBMs in solving water purification challenges and encourages innovative solutions in this field.

In Situ Polymerization of Methylene Blue on Bacterial Cellulose for Photodynamic/Photoelectricity Synergistic Inhibition of Bacterial Biofilm Formation

In the context of long-term antimicrobial treatment, the emergence of bacterial resistance poses a significant challenge. Therefore, there is a pressing need to develop novel antimicrobial materials and methods that can effectively and safely combat microbial infections. This study focuses on the synthesis of bacterial cellulose-polymethylene blue (BC-PMB) with integrated photodynamic and photoelectric antimicrobial properties. The polymerization of methyl blue (MB) onto bacterial celluloses (BC) was achieved, and through comprehensive computational analyses using density functional theory (DFT) and molecular dynamics simulations, it was confirmed that this polymerization greatly enhanced the binding efficiency between methylene blue and BC. Additionally, polymethylene blue (PMB) exhibited superior photoexcitation efficiency and conductivity compared to its precursor. When BC-PMB was exposed to a 30 mW 660 nm light source for 30 min, the material demonstrated a remarkable antimicrobial efficacy of 93.99% against Escherichia coli and 98.58% against Staphylococcus aureus. Furthermore, the synergistic effect of photodynamic and photoelectric antimicrobial mechanisms exhibited long-term inhibitory capabilities against bacterial biofilms.

Removal of Methylene Blue and Congo Red Using a Chitosan-Graphene Oxide-Electrosprayed Functionalized Polymeric Nanofiber Membrane

Untreated textile effluent may contain toxic organic pollutants that can have negative impacts on the ecosystem. Among the harmful chemicals present in dyeing wastewater, there are two frequently used organic dyes: methylene blue (cationic) and congo red (anionic). The current study presents investigations on a novel two-tier nanocomposite membrane, i.e., a top layer formed of electrosprayed chitosan-graphene oxide and a bottom layer consisting of an ethylene diamine functionalized polyacrylonitrile electrospun nanofiber for the simultaneous removal of the congo red and methylene blue dyes. The fabricated nanocomposite was characterized using FT-IR spectroscopy, scanning electron microscopy, UV-visible spectroscopy, and Drop Shape Analyzer. Isotherm modeling was used to determine the efficiency of dye adsorption for the electrosprayed nanocomposite membrane and the confirmed maximum adsorptive capacities of 182.5 mg/g for congo red and 219.3 mg/g for methylene blue, which fits with the Langmuir isotherm model, suggesting uniform single-layer adsorption. It was also discovered that the adsorbent preferred an acidic pH level for the removal of congo red and a basic pH level for the removal of methylene blue. The gained results can be a first step for the development of new wastewater cleaning techniques.

Fabrication of EVOH/PANI Composite Nanofibrous Aerogels for the Removal of Dyes and Heavy Metal Ions

Water pollution caused by the leakage and discharge of pollutants, such as dyes and heavy metal ions, can cause serious damage to the environment and human health. Therefore, it is important to design and develop adsorbent materials that are efficient and multifunctional for the removal of these pollutants. In this work, poly(vinyl alcohol-co-ethylene) (EVOH)/polyaniline (PANI) composite nanofibrous aerogels (NFAs) were fabricated via solution oxidation and blending. The aerogels were characterized by a scanning electron microscope, Fourier transform infrared spectrometry, a contact angle measuring instrument and a universal testing machine. The influences of the introduction of PANI nanorods on the structural properties of aerogels were investigated, and the adsorption performance of aerogels was also studied. The results showed that the introduction of PANI nanorods filled the fibrous network structure, reduced porosity, increased surface hydrophilicity and improved compressive strength. Furthermore, EVOH/PANI composite NFAs possess good adsorption performances for dyes and heavy metal ions: The adsorption capacities of methyl orange and chromium ions (VI) are 73.22 mg/g and 115.54 mg/g, respectively. Overall, the research suggests that EVOH/PANI NFAs have great potential as efficient and multifunctional adsorbent materials for the removal of pollutants from water.

Chitosan-Graphene Oxide Dip-Coated Polyacrylonitrile-Ethylenediamine Electrospun Nanofiber Membrane for Removal of the Dye Stuffs Methylene Blue and Congo Red

Textile wastewater accommodates many toxic organic contaminants that could potentially threaten the ecosystem if left untreated. Methylene blue is a toxic, non-biodegradable, cationic dye that is reportedly observed in significant amounts in the textile effluent stream as it is widely used to dye silk and cotton fabrics. Congo red is a carcinogenic anionic dye commonly used in the textile industry. This study reports an investigation of methylene blue and Congo red removal using a chitosan-graphene oxide dip-coated electrospun nanofiber membrane. The fabricated nanocomposite was characterized using Scanning Electron Microscopy (SEM), FT-IR Spectroscopy, Raman Spectroscopy, UV-vis Spectroscopy, Drop Shape Analyzer, and X-ray Diffraction. The isotherm modeling confirmed a maximum adsorptive capacity of 201 mg/g for methylene blue and 152 mg/g for Congo red, which were well fitted with a Langmuir isotherm model indicating homogenous monolayer adsorption.

Selective separation of dyes by green composite membrane based on polylactide with carboxylated cellulose microfiber from empty fruit bunch

A bio-based membrane was prepared by a non-solvent induced phase separation process. A polylactide (PLA)/poly(butylene adipate-co-terephthalate) (PBAT) polymer blend was mixed with functionalized cellulose microfiber from empty fruit bunch (EFB) modified with maleic anhydride (MEFB). MEFB reduced the water contact angle and increased the porosity of the membrane. In a batch adsorption process, the pseudo-second order and Langmuir isotherm models best described the adsorption of the cationic dye methylene blue (MB) on PLA/PBAT and PLA/PBAT-MEFB membranes. In a dynamic adsorption process, pure water flux was higher through the PLA/PBAT-MEFB membrane (1214 L m^-2 h^-1) than the PLA/PBAT membrane (371 L m^-2 h^-1). The PLA/PBAT-MEFB membrane removed 97.2 % of MB while the PLA/PBAT membrane removed only 58.7 %. The hydrophilicity of the membrane and its adsorption efficiency toward MB were improved by the abundant carboxyl groups in MEFB. A filtration test using a mixed dye solution of anionic methyl orange (MO) and MB showed that the PLA/PBAT-MEFB membrane rapidly adsorbed MB while permitting MO to pass through. Moreover, this membrane could be easily regenerated and maintained a satisfactory separation performance over several cycles. Based on the membrane performance and its economical preparation, the proposed biocomposite membrane could be used for selective filtration and wastewater treatment.

Recent progress on electrospun nanofibrous polymer membranes for water and air purification: A review

Developing new polymer membranes with excellent thermal, mechanical, and chemical stability has shown great potential for various environmental remediation applications such as wastewater treatment and air filtration. Polymer membranes have been widely investigated over the past years and utilized to overcome severe ecological issues. Membrane-based technologies play a critical role in water purification and air filtration with the ability to act efficiently and sustainably. Electrospun nanofiber membranes have displayed excellent performance in removing various contaminants from water, such as bacteria, dyes, heavy metals, and oil. These nanofibrous membranes have shown good potential to filter the air from tiny particles, volatile organic compounds, and toxic gases. The performance of polymer membranes can be enhanced by fine-tuning polymer structure, varying surface properties, and strengthening overall membrane porosity. In this review, we discuss the involvement of electrospun nanofibrous membranes in different environmental remediation applications. It further reviews the recent progress of polymer membrane development by utilizing nanoparticles and naturally occurring polymers.

Ofloxacin Removal from Aqueous Media by Means of Magnetoactive Electrospun Fibrous Adsorbents

Functionalized electrospun polymer microfibrous membranes were fabricated by electrospinning and further surface-functionalized with magnetic iron oxide (Fe_xO_y) nanoparticles to yield magnetoactive nanocomposite fibrous adsorbents. The latter were characterized in respect to their morphology, mechanical properties and magnetic properties while they were further evaluated as substrates for removing Ofloxacin (OFL) from synthetic aqueous media and secondary urban wastewater (UWW) under varying physicochemical parameters, including the concentration of the pharmaceutical pollutant, the solution pH and the membranes' magnetic content. The magnetic-functionalized fibrous adsorbents demonstrated significantly enhanced adsorption efficacy in comparison to their non-functionalized fibrous analogues while their magnetic properties enabled their magnetic recovery and regeneration.

Removal of organic micropollutans by adsorptive membrane

Various emerging organic micropollutants, such as pharmaceuticals, have attracted the interest of the water industry during the last two decades due to their insufficient removal during conventional water and wastewater treatment methods and increasing demand for pharmaceuticals projected to climate change-related impacts and COVID-19, nanosorbents such as carbon nanotubes (CNTs), graphene oxides (GOs), and metallic organic frameworks (MOFs) have recently been extensively explored regarding their potential environmental applications. Due to their unique physicochemical features, the use of these nanoadsorbents for organic micropollutans in water and wastewater treatment processes has been a rapidly growing topic of research in recent literature. Adsorptive membranes, which include these nanosorbents, combine the benefits of adsorption with membrane separation, allowing for high flow rates and faster adsorption/desorption rates, and have received a lot of publicity in recent years. The most recent advances in the fabrication of adsorptive membranes (including homogeneous membranes, mixed matrix membranes, and composite membranes), as well as their basic principles and applications in water and wastewater treatment, are discussed in this review. This paper covers ten years, from 2011 to 2021, and examines over 100 published studies, highlighting that micropollutans can pose a serious threat to surface water environments and that adsorptive membranes are promising, particularly in the adsorption of trace substances with fast kinetics. Membrane fouling, on the other hand, should be given more attention in future studies due to the high costs and restricted reusability.

Novel fabricated low-cost hybrid polyacrylonitrile/polyvinylpyrrolidone coated polyurethane foam (PAN/PVP@PUF) membrane for the decolorization of cationic and anionic dyes

Dyes are recalcitrait organic pollutants threatening the aquatic environment and human health. In the present study, a novel low-cost hybrid membrane was fabricated by coating polyurethane foam (PUF) with polyacrylonitrile/polyvinylpyrrolidone (PAN/PVP) via phase inversion technique from casting solutions consisting of PAN and PVP with Dimethyl formamide (DMF) and applied for removal of cationic (Methylene Blue (MB)) and anionic (Methyl Orange (MO)) dyes from aqueous solutions. The as-prepared membrane was first characterized by Scan Electron Microscope (SEM), Fourier Transform Infrared (FTIR), Energy Dispersive Spectrometry (EDS), etc. Then, batch experiments were conducted to optimize the adsorption conditions, including contact time, adsorbent dose, dyes concentration, and pH. The dye removal results fitted with pseudo first and second-order kinetics; Langmuir, Freundlich, and Temkin isotherms' models. The maximum dye decolorization was approximately 97% and 95% within 60 and 120 min using 0.5 and 1 g of the fabricated composite for MB and MO, respectively. The kinetic studies showed rapid sorption dynamics following a second-order kinetic model. In addition, dye adsorption equilibrium data fitted well to the Freundlich isotherm with monolayer maximum adsorption capacity of 6.356 and 3.321 mg/g for MO and MB dye, respectively. Thus, the novel hybrid membrane is promising as a cheap and efficient adsorbent for the removal of both cationic and anionic dyes from wastewater. The current study demonstrated a new avenue to achieve efficient management of dyes in aquatic environments.

Hemp fibers modified with graphite oxide as green and efficient solution for water remediation: Application to methylene blue

In this paper, the use of hemp fibers modified with graphite oxide for the removal of methylene blue (MB) from aqueous solutions was investigated. Parameters such as contact time, pH, temperature, initial concentration of dye and ionic strength were varied and their effects on the adsorption recovery were evaluated. The adsorption process attained the equilibrium within 30 min while the adsorption capacity was found to increase with increasing contact time. The experimental data were fitted through a pseudo-second order model. Maximum adsorption capacity slightly increases with temperature changing from 54 mg/g to 58 mg/g at pH = 7.5, from 37 mg/g to 45 mg/g at pH = 3 and from 44 mg/g to 49 mg/g at pH = 12, by increasing the temperature from 20 °C to 80 °C indicating that the process is slightly endothermic (ΔH = 3.43 kJ/mol). The thermodynamic parameters were even calculated demonstrating that the process is spontaneous (ΔG ≈ -4.4 J/mol K and ΔS = 3.16 J/mol K)). Finally, a mathematical algorithm was applied to forecast the response surface model. A second order model was chosen to fit the experimental data and the statistical effect of the process parameters were estimated. A numerical optimization was even performed to individuate the optimal set of process parameters (pH = 9.25, T = 53.8 °C and C₀ = 13.2 mg/L) which maximizes the removal capacity. A possible adsorption mechanism was even presented. So, it was proved the efficiency of the adsorption of a novel, inexpensive and sustainable composite material obtained from agro-waste resources by performing reusability cycles.

How the Carbonization Time of Sugarcane Biomass Affects the Microstructure of Biochar and the Adsorption Process?

Biochars (BCs) are very versatile adsorbents, mainly, in the effectiveness of adsorption of organic and inorganic compounds in aqueous solutions. Here, the sugarcane biomass (SCB) was used to produce biochar at different carbonization times: 1, 2, 3, 4, and 5 h, denominated as BC1, BC2, BC3, BC4, and BC5, respectively. The superficial reactivity was studied with adsorption equilibrium experiments and kinetics models; Methylene Blue (MB) was used as adsorbate at different pH values, concentrations, and temperatures. In summary, the carbonization time provides the increase of superficial area, with exception of BC4, which decreased. Equilibrium studies showed inflection points and fluctuations with different initial dye concentration and temperature; SCB showed the best adsorption capacity compared to the BCs at the three temperatures tested, varying with the increase of MB concentration, suggesting the dependence of these two main factors on the adsorption process. The proposed adsorption mechanism suggests the major influence of Coulomb interactions, H-bonding, and π-interactions on the adsorption of MB onto adsorbents, evidencing that the adsorption is led by physical adsorption. Therefore, the results led to the use of the SCB without carbonization at 200 °C, saving energy and more adsorbent mass, considering that the carbonization influences weight loss. This study has provided insights of the use of SCB in MB dye adsorption as a low-cost and eco-friendly adsorbent.

Electrospun 1D-NiO hollow nanowires on glass support for the sunlight-driven photodegradation of methylene blue

Sunlight-driven semiconductor photocatalysts have received substantial attention due to environmental degradation, but a simple and reusable photocatalyst design has been a challenging task. Herein, we report the fabrication of a one-dimensional hollow semiconducting nanowire structure by electrospun-mediated nickel oxide nanowires (NiO NWs) as a reusable photocatalyst by direct deposition on glass substrates. The effective control of the sunlight-driven hollow nanowires as the photocatalyst has a high surface area for multiple light-harvesting and interface redox reactions, a nanostructured thin shell for accelerated charge separation, transportation, and a large length-diameter ratio for easy recycling. The electrospun NiO NWs were nest-like hollow nanostructure fibers, crystalline, and with a high density, and the synthesis and parameters were thoroughly investigated to achieve the characteristic shape of the hollow NiO NWs. Further, the photocatalytic activity of the NiO NWs on glass substrates for the selective breakdown of methylene blue (MB) under sunlight irradiation to optimize the efficiency of the NiO NWs, such as degradation techniques, concentration, and pH of the MB solution. The stability and reusability of the NiO NWs were tested successfully in several reusable cycles, with only a 2% degradation difference. The reaction rate was found to be 0.054 min⁻¹ for MB (5 μM) and 0.033 min⁻¹ for MB (10 μM) at pH 11 for 60 min, and the higher activity parameter was calculated to be 3.3 × 10⁻³ min⁻¹ mg⁻¹ L⁻¹ due to their hollow structure and effective area of the NiO NWs. They contain more superficially-entrapped holes that change with chemisorbed oxyhydroxyl OH or H₂O to form OH⁻ radicals. The specific active hollow surface area rises, whereas the rate of optical-electronic hole recombination drops. The photocatalytic degradation performance of the fabricated one-step electrospun hollow NiO NW-based photocatalyst on substrates showed speed, reusability, and promoted the formation of radicals capable of decomposing organic pollutants, which were shown to have application in photocatalysis.

One-step fabrication of hollow NiO NWs photocatalyst on glass substrate by electrospun then tested for their capacity to break down MB in solutions exposed to sunlight.

Adsorptive Recovery of Cu2+ from Aqueous Solution by Polyethylene Terephthalate Nanofibres Modified with 2-(Aminomethyl)Pyridine

The accumulation of plastic waste products in the environment has adversely affected wildlife and human beings. Common plastics that accumulate in the environment are plastics that are made of polyethylene terephthalate (PET) polymer. PET plastic waste products can be recycled for beneficial use, which would reduce their negative impacts. In this study, modified PET or waste PET (WPET) from plastic bottles was blended with powder commercial 2-(aminomethyl)pyridine (SiAMPy) resin and electrospun into composite nanofibres and applied for Cu2+ adsorption. PET-SiAMPy or WPET-SiAMPy composite nanofibres fibre diameters from the HRSEM images were 90–140 nm and 110–155 nm, respectively. In batch adsorption experiments, PET-SiAMPy or WPET-SiAMPy composite nanofibres achieved Cu2+ adsorption equilibrium within 60 secs of contact time with 0.98 mmol/g (89.87%) or 1.24 mmol/g (96.04%) Cu2+ adsorption capacity. The Cu2+ complex formation rate (k) with WPET-SiAMPy was 0.0888 with the mole ratio of Cu2+ and WPET-SiAMPy nanofibres 1:2. The complex molecular formula formed was Cu(WPET-SiAMPy)2 with a square planar geometry structure. The WPET-SiAMPy nanofibres’ adsorption was best fitted to the Freundlich isotherm. WPET-SiAMPy composite nanofibres were considered highly efficient for Cu2+ adsorption from aqueous solution and could be regenerated at least five times using 5 M H2SO4.

Sustainable Treatment of Food Industry Wastewater Using Membrane Technology: A Short Review

Water is needed for food processing facilities to carry out a number of tasks, including moving goods, washing, processing, and cleaning operations. This causes them to produce wastewater effluent, and they are typically undesirable since it contains a high volume of suspended solids, bacteria, dyestuffs, salts, oils, fats, chemical oxygen demand and biological oxygen demand. Therefore, treatment of food industry wastewater effluent is critical in improving process conditions, socio-economic benefits and our environmental. This short review summarizes the role of available membrane technologies that have been employed for food wastewater treatment and analyse their performance. Particularly, electrospun nanofiber membrane technology is revealed as an emerging membrane science and technology area producing materials of increasing performance and effectiveness in treating wastewater. This review reveals the challenges and perspectives that will assist in treating the food industry wastewater by developing novel membrane technologies.

Graphene oxide loaded fibrous matrixes of polyether block amide (PEBA) elastomer as an adsorbent for removal of cationic dye from wastewater

Novel highly porous nanoparticle materials are increasingly being applied in adsorption processes, but they need to be supported by robust matrixes to maintain their functionality. We present a study of hosting graphene oxide (GO) particles on polyether block amide (PEBA) melt electrospun fibers and applying such composite matrix to the adsorption of the cationic dye (crystal violet) from water. Various amounts of GO (from 0.5 to 2.0%) were mixed into pure PEBA and electrospun by melt electrospinning obtaining micro fibrous matrixes. These were characterized for morphology (SEM), chemical composition (FTIR), crystallinity (XRD), and wetting behavior (WCA). The increasing amount of GO adversely affected fiber diameter (reduced from 13.18 to 4.38 μm), while the hydrophilic properties (Water contact angle decrease from 109 to 76°) and overall dye adsorption was increased. Efficient adsorption has been demonstrated, reaching approximately 100 % removal efficiency using a 2% GO composite matrix at a dose of 40 mg/l and pH of 10. Further increase of GO concentration in polymer is not feasible due to instability in the electrospinning process.

Biodegradable polymers and their nano-composites for the removal of endocrine-disrupting chemicals (EDCs) from wastewater: A review

Endocrine-disrupting chemicals (EDCs) target the endocrine system by interfering with the natural hormones in the body leading to adverse effects on human and animal health. These chemicals have been identified as major polluting agents in wastewater effluents. Pharmaceuticals, personal care products, industrial compounds, pesticides, dyes, and heavy metals are examples of substances that could be considered endocrine active chemicals. In humans, these chemicals could cause obesity, cancer, Alzheimer's disease, autism, reproductive abnormalities, and thyroid problems. While in wildlife, dysfunctional gene expression could lead to the feminization of some aquatic organisms, metabolic diseases, cardiovascular risk, and problems in the reproductive system as well as its levels of hatchability and vitellogenin. EDCs could be effectively removed from wastewater using advanced technologies such as reverse osmosis, membrane treatment, ozonation, advanced oxidation, filtration, and biodegradation. However, adsorption has been proposed as a more promising and sustainable method for water treatment than any other reported technique. Increased attention has been paid to biodegradable polymers and their nano-composites as promising adsorbents for the removal of EDCs from wastewater. These polymers could be either natural, synthetic, or a combination of both. This review presents a summary of the most relevant cases where natural and synthetic biodegradable polymers have been used for the successful removal of EDCs from wastewater. It demonstrates the effectiveness of these polymers as favorable adsorbents for novel wastewater treatment technologies. Hitherto, very limited work has been published on the use of both natural and synthetic biodegradable polymers to remove EDCs from wastewater, as most of the studies focused on the utilization of only one type, either natural or synthetic. Therefore, this review could pave the way for future exploration of biodegradable polymers as promising and sustainable adsorbents for the removal of various types of pollutants from wastewater.

Chemical Oxidative Polymerization of Methylene Blue: Reaction Mechanism and Aspects of Chain Structure

The kinetic regularities of the initial stage of chemical oxidative polymerization of methylene blue under the action of ammonium peroxodisulfate in an aqueous medium have been established by the method of potentiometry. It was shown that the methylene blue polymerization mechanism includes the stages of chain initiation and growth. It was found that the rate of the initial stage of the reaction obeys the kinetic equation of the first order with the activation energy 49 kJ × mol^-1. Based on the proposed mechanism of oxidative polymerization of methylene blue and the data of MALDI, EPR, and IR spectroscopy methods, the structure of the polymethylene blue chain is proposed. It has been shown that polymethylene blue has a metallic luster, and its electrical conductivity is probably the result of conjugation over extended chain sections and the formation of charge transfer complexes. It was found that polymethylene blue is resistant to heating up to a temperature of 440 K and then enters into exothermic transformations without significant weight loss. When the temperature rises above 480 K, polymethylene blue is subject to endothermic degradation and retains 75% of its mass up to 1000 K.

Modified Electrospun Polymeric Nanofibers and Their Nanocomposites as Nanoadsorbents for Toxic Dye Removal from Contaminated Waters: A Review

Electrospun polymer nanofibers (EPNFs) as one-dimensional nanostructures are characterized by a high surface area-to-volume ratio, high porosity, large number of adsorption sites and high adsorption capacity. These properties nominate them to be used as an effective adsorbent for the removal of water pollutants such as heavy metals, dyes and other pollutants. Organic dyes are considered one of the most hazardous water pollutants due to their toxic effects even at very low concentrations. To overcome this problem, the adsorption technique has proven its high effectiveness towards the removal of such pollutants from aqueous systems. The use of the adsorption technique depends mainly on the properties, efficacy, cost and reusability of the adsorbent. So, the use of EPNFs as adsorbents for dye removal has received increasing attention due to their unique properties, adsorption efficiency and reusability. Moreover, the adsorption efficiency and stability of EPNFs in aqueous media can be improved via their surface modification. This review provides a relevant literature survey over the last two decades on the fabrication and surface modification of EPNFs by an electrospinning technique and their use of adsorbents for the removal of various toxic dyes from contaminated water. Factors affecting the adsorption capacity of EPNFs, the best adsorption conditions and adsorption mechanism of dyes onto the surface of various types of modified EPNFs are also discussed. Finally, the adsorption capacity, isotherm and kinetic models for describing the adsorption of dyes using modified and composite EPNFs are discussed.