Catalysts for nitrogen reduction to ammonia

Co-Ni bimetallic oxide with tuned surface oxygen vacancies efficiently electrocatalytic reduction of nitrate to ammonia

The electrocatalytic reduction reaction of nitrate (NO3-) to ammonia (NH3) provides an efficient and clean NH3 production method, which has the potential to replace the traditional industrial preparation methods. However, the limited activity and Faraday efficiency (FE) of existing catalysts impede the practical application of this technology. Herein, in this work, a high-performance catalyst with high NH3 yield and FE was fabricated. Co-Ni bimetallic oxide (NiCo2O4) catalysts with tuned surface oxygen vacancies (OVs) contents were prepared by changing the heating rate during calcination, NiCo2O4 calcined at a heating rate of 5 °C/min (NiCo2O4-5) possessed the highest surface OVs content. Experimental studies showed that NiCo2O4 with higher surface OVs had better NO3RR activity, inhibited the production of nitrite (NO2-), and exhibited higher selectivity to NH3. Among prepared catalysts, NiCo2O4-5 demonstrated superior performance in electrocatalytic reduction of NO3- to NH3, achieving a high NH3 FE (94.4 %) and yield (193.2 mmol/h g-1) at a suitable applied voltage. Besides, in situ Fourier transform infrared spectroscopy analysis suggested that NiCo2O4-5 preferentially followed the NO3RR pathway as follows: *NO3 → *HNO3 → *NO2 → *HNO2 → *NO → *HNO → *N → *NH → *NH2 → *NH3.

Investigating the Molybdenum Nitrogenase Mechanistic Cycle Using Spectroelectrochemistry

Molybdenum nitrogenase plays a crucial role in the biological nitrogen cycle by catalyzing the reduction of dinitrogen (N2) to ammonia (NH3) under ambient conditions. However, the underlying mechanisms of nitrogenase catalysis, including electron and proton transfer dynamics, remain only partially understood. In this study, we covalently attached molybdenum nitrogenase (MoFe) to gold electrodes and utilized surface-enhanced infrared absorption spectroscopy (SEIRA) coupled with electrochemistry techniques to investigate its catalytic mechanism. Our biohybrid system enabled electron transfer via a mild mediator, likely mimicking the natural electron flow through the P-cluster to FeMoco, the enzyme's active site. For the first time, we experimentally observed both terminal and bridging S-H stretching frequencies, resulting from the protonation of bridging sulfides in FeMoco during turnover conditions providing direct evidence of their role in catalysis. These experimental observations are further supported by QM/MM calculations. Additionally, we investigated CO inhibition, demonstrating both CO binding and unbinding dynamics under electrochemical conditions. These insights not only advance our understanding of the mechanistic cycle of molybdenum nitrogenase but also establish a foundation for studying alternative nitrogenases, including vanadium and iron nitrogenases.

Novel two-dimensional molybdenene as a promising electrocatalyst for the nitrogen reduction reaction: a first-principles prediction

The exploration of two-dimensional (2D) metallenes is driven by their noteworthy attributes, encompassing high conductivity and substantial exposure of metal active sites, facilitating the development of nitrogen reduction reaction (NRR) electrocatalysts characterized by a low overpotential and superior selectivity. Here, employing first-principles swarm-intelligence structural search methods, we predict molybdenene as a novel and stable non-precious metallene, featuring a 2-atom-thick structure. Our findings demonstrate that the basal plane of molybdenene showcases remarkable catalytic activity with an overpotential of 0.27 V. Bader charge analysis reveals that the exposed Mo bonded to NxHy groups not only transfers electrons to these groups but also the remaining Mo transfers electrons to NxHy upon the breaking of NN bonds. This electron transfer mechanism contributes to elevated NRR catalytic activity. Our work broadens the scope of metallenes as promising electrocatalysts for the NRR with the expectation that more attention will be paid to emerging metallenes, thus offering a modest contribution to the theoretical exploration, fundamental understanding and practical application of metallenes.

Dinitrogen Activation and Conversion by Actinide Complexes

The efficient activation and conversion of dinitrogen (N2) represent a significant challenge in sustainable chemistry, offering potential pathways for synthesizing valuable nitrogen-containing compounds while reducing the environmental impact of traditional nitrogen fixation processes. While transition metal catalysts have been extensively studied for this purpose, actinide complexes have been less explored but have recently emerged as promising candidates due to their unique electronic properties and reactivity. This Perspective systematically examines the recent advances in N2 activation and conversion mediated by actinide complexes, with a particular focus on their synthesis, mechanistic insights, and catalytic capabilities.

Overcoming Gas Mass Transfer Limitations Using Gas-Conducting Electrodes for Efficient Nitrogen Reduction

Electrocatalytic nitrogen reduction reaction (NRR) is a very attractive strategy for ammonia synthesis due to its energy savings and sustainability. However, the ammonia yield and Faraday efficiency of electrocatalytic nitrogen reduction have been challenges due to low nitrogen solubility and competitive hydrogen evolution reaction (HER) in electrolyte solution. Herein, inspired by the asymmetric wetting behavior, i.e., superhydrophobicity/hydrophilicity, of floating lotus leaves, we demonstrated a gas-conduction electrode with asymmetric gas wetting behavior on the opposite surface, i.e., Janus-Ni/MoO2@NF, for efficient nitrogen reduction. It can provide an abundant three-phase interface (TPI) at interfaces of Janus-Ni/MoO2@NF in electrolyte solution to enhance the contact among N2, electrolyte, and electrode. Ascribed to this advantage, the hydrophobic side of the Janus electrode not only can repel water molecules to suppress the HER process but also can increase the concentration of N2 on the interface microenvironment. Consequently, the well-designed gas-conducting electrode breaks gas mass transfer limitation. Furthermore, Janus-Ni/MoO2@NF delivers a record-high NH3 yield rate of 5.865 μg·h-1·cm-2 and a Faradaic efficiency of 36.14% at an extremely low potential of 0 V vs RHE in 0.1 M Na2SO4 under ambient conditions, which are 22 and 18 times higher than those of the conventional electrode, respectively. Therefore, the gas-conducting electrodes can dramatically improve the activity and selectivity in electrocatalytic NRR. Additionally, the unique interface design provides inspiration for other sustainable electrochemical reactions involving gas electrocatalytic correlation.

Advanced Ruthenium-Based Electrocatalysts for NOx Reduction to Ammonia

Ammonia (NH3) is widely recognized as a crucial raw material for nitrogen-based fertilizer production and eco-friendly hydrogen-rich fuels. Currently, the Haber-Bosch process still dominates the worldwide industrial NH3 production, which consumes substantial energy and contributes to enormous CO2 emission. As an alternative NH3 synthesis route, electrocatalytic reduction of NOx species (NO3 -, NO2 -, and NO) to NH3 has gained considerable attention due to its advantages such as flexibility, low power consumption, sustainability, and environmental friendliness. This review timely summarizes an updated and critical survey of mechanism, design, and application of Ru-based electrocatalysts for NOx reduction. First, the reason why the Ru-based catalysts are good choice for NOx reduction to NH3 is presented. Second, the reaction mechanism of NOx over Ru-based materials is succinctly summarized. Third, several typical in situ characterization techniques, theoretical calculations, and kinetics analysis are examined. Subsequently, the construction of each classification of the Ru-based electrocatalysts according to the size of particles and compositions is critically reviewed. Apart from these, examples are given on the applications in the production of valuable chemicals and Zn-NOx batteries. Finally, this review concludes with a summary highlighting the main practical challenges relevant to selectivity and efficiency in the broad range of NOx concentrations and the high currents, as well as the critical perspectives on the fronter of this exciting research area.

Engineering a Photoautotrophic Microbial Coculture toward Enhanced Biohydrogen Production

The application of synthetic phototrophic microbial consortia holds promise for sustainable bioenergy production. Nevertheless, strategies for the efficient construction and regulation of such consortia remain challenging. Applying tools of genetic engineering, this study successfully constructed a synthetic community of phototrophs using Rhodopseudomonas palustris (R. palustris) and an engineered strain of Synechocystis sp PCC6803 for acetate production (Synechocystis_acs), enabling the production of biohydrogen and fatty acids during nitrogen and carbon dioxide fixation. Elemental balance confirmed carbon capture and nitrogen fixation into the consortium. The strategy of circadian illumination effectively limited oxygen levels in the system, ensuring the activity of the nitrogenase in R. palustris, despite oxygenic photosynthesis happening in Synechocystis. When infrared light was introduced into the circadian illumination, the production of H2 (9.70 μmol mg-1) and fatty acids (especially C16 and C18) was significantly enhanced. Proteomic analysis indicated acetate exchange and light-dependent regulation of metabolic activities. Infrared illumination significantly stimulated the expression of proteins coding for nitrogen fixation, carbohydrate metabolism, and transporters in R. palustris, while constant white light led to the most upregulation of photosynthesis-related proteins in Synechocystis_acs. This study demonstrated the successful construction and light regulation of a phototrophic community, enabling H2 and fatty acid production through carbon and nitrogen fixation.

Beyond the triple bond: unlocking dinitrogen activation with tailored superbase phosphines

Activating atmospheric dinitrogen (N2), a molecule with a remarkably strong triple bond, remains a major challenge in chemistry. This theoretical study explores the potential of superbase phosphines, specifically those decorated with imidazolin-2-imine ((ImN)3P) and imidazolin-2-methylidene ((ImCH)3P) to facilitate N2 activation and subsequent hydrazine (H2NNH2) formation. Using density functional theory (DFT) at the M06L/6-311++G(d,p) level, we investigated the interactions between these phosphines and N2. Mono-phosphine-N2 complexes exhibit weak, noncovalent interactions (-0.6 to -7.1 kcal mol-1). Notably, two superbasic phosphines also form high-energy hypervalent complexes with N2, albeit at significantly higher energies. The superbasic nature and potential for the hypervalency of these phosphines lead to substantial N2 activation in bis-phosphine-N2 complexes, where N2 is "sandwiched" between two phosphine moieties through hypervalent P-N bonds. Among the phosphines studied, only (ImN)3P forms an exothermic sandwich complex with N2, stabilized by hydrogen bonding between the ImN substituents and the central N2 molecule. A two-step, exothermic hydrogen transfer pathway from (ImN)3P to N2 results in the formation of a bis-phosphine-diimine (HNNH) sandwich complex. Subsequent hydrogen transfer leads to the formation of a bis-phosphine-hydrazine (H2NNH2) complex, a process that, although endothermic, exhibits surmountable activation barriers. The relatively low energy requirements for this overall transformation suggest its potential feasibility under the optimized conditions. This theoretical exploration highlights the promise of superbase phosphines as a strategy for metal-free N2 activation, opening doors for the development of more efficient and sustainable nitrogen fixation and utilization methods.

Graphitic Carbon Nitride Supported Boron Quantum Dots: A Transition Metal Free Alternative for Di-Nitrogen to Ammonia Reaction

Presently, a sustainable electrochemical Nitrogen Reduction Reaction (NRR) has been essentially found to be viable on transition metal-based catalysts. However, being cost-effective and non-corrosive, metal-free catalysts present an ideal solution for a sustainable world. Herein, through a DFT-based study, we demonstrate metal-free NRR catalysts, boron quantum dots with 13 atoms as a case study and their chemically modified counterparts when anchored on graphitic carbon nitride (g-C3N4) surface. The best catalyst among the studied, a silicon-doped boron quantum dot with a cagelike structure, is found to favour the dinitrogen to ammonia reaction pathway with a low liming potential and potential rate-determining step (PDS) of -0.11 V and 0.27 eV, respectively. The present work demonstrates as to how boron quantum dots, which are reported to be experimentally synthesised, can be exploited for ammonia synthesis when supported on the surface. These catalysts effectively suppress the HER, thus establishing its suitability as an ideal catalyst. The work also represents a futuristic pathway towards a metal-free catalyst for NRR.

Promoting Electrochemical Nitrate Reduction to Ammonia on Silver Nanocrystals Doped with Iron Series Elements

Electrochemical nitrate reduction to ammonia (NRA) is a promising approach to remove environmental pollutants while producing green NH3 under ambient conditions. Ag-based nanomaterials have been used in NRA but their iron series elements (Fe, Co, Ni) doping has not been explored yet. Herein, an effective and versatile doping strategy of Ag nanocrystals by iron series elements for efficient NRA is presented. Experimental results show that doping with Fe, Co or Ni can improve the NRA activity. Among the catalysts, AgCo delivers the best performance with a Faraday efficiency (FE) of 88.3 % and ammonia selectivity of 97.4 % at-0.23 V vs RHE, which is 1.9 and 6.2 times higher than that of plain Ag (46.4 % FE and 15.8 % selectivity), respectively. A highest NO3 - conversion rate of AgCo (91.8 %) is achieved, which maintains 16.4 ppm NO3 --N in 4 hours, meeting the drinking water level (~15 ppm NO3 --N). Moreover, the FE, selectivity, conversion rate of AgCo do not decay after the four consecutive cycles. It is found that Co doping can effectively induce the change of Ag d-band center for optimized NRA. This work reveals doping effects of iron series elements on Ag-based catalysts, and shows potential practical application in NRA.

Promoted Two-Step Ammonia Synthesis with CoOOH/Co foam at Ampere-Level Current Density and Nearly 100% Faraday Efficiency from Air and Water

Ammonia (NH3) is regarded as an essential hydrogen storage material in the new energy field, and plasma-electrocatalytic synthesis of NH3 (PESA) is an alternative to the traditional Haber-Bosch process. Here, a bifunctional catalyst CoOOH/CF is proposed to enhance the PESA process. Benefiting from the efficient activation of O2 by CoOOH/CF, NOx - yield rate can reach the highest value of 171.90 mmol h-1 to date. Additionally, CoOOH holds a more negative d-band center, thereby exhibiting weaker adsorption toward NO*, lowering the energy barrier for the rate determining step, resulting in a high NH3 yield rate (302.55 mg h-1 cm-2 at -0.8 V) with ampere-level NH3 current density (2.86 A cm-2 at -0.8 V) and nearly 100% Faraday efficiency (FE, 99.8% at -0.6 V). Moreover, CoOOH/CF achieves an excellent 4.54 g h-1 NH3 yield rate with 97.9% FE in an enlarged electrolyzer, demonstrating the feasibility of PESA on a large scale.

Valorization systems based on electrocatalytic nitrate/nitrite conversion for energy supply and valuable product synthesis

The excessive accumulation of nitrate/nitrite (NO x -) in surface and groundwater has severely disrupted the global nitrogen cycle and jeopardized public health. The electrochemical conversion of NO x - to ammonia (NH3) not only holds promise for ecofriendly NO x - removal, but also provides a green alternative to the energy-intensive Haber-Bosch process for NH3 production. Recently, in addition to the electrocatalyst design explosion in this field, many innovative valorization systems based on NO x --to-NH3 conversion have been developed for generating energy and expanding the range of value-added products. Collective knowledge of advanced conversion systems is indispensable for restoring the global nitrogen cycle and promoting a N-based economy. Herein, a timely and comprehensive review is provided on the important progress of valorization systems based on NO x - conversion, including waste treatment systems, novel electrolytic systems, and energy conversion and storage systems. Some mechanism explorations, device designs, key electrode developments and feasibility analyses are involved to gain deeper understanding of various systems and facilitate implementing these cleaning systems in industry. Finally, challenges and future prospects are outlined in the NO x - conversion field with an aim to promote large-scale electrocatalytic system development and prosperous N-based electrochemistry.

Nitrogen fixation by methanogenic Archaea, literature review and DNA database-based analysis; significance in face of climate change

Archaea represents a significant population of up to 10% in soil microbial communities. The role of Archaea in soil is often overlooked mainly due to its unculturability. Among the three domains of life biological nitrogen fixation (BNF) is mainly a trait of Eubacteria and some Archaea. Archaea mediated processes like BNF may become even more important in the face of global Climate change. Although there are reports on nitrogen fixation by Archaea, to best of our knowledge there is no comprehensive report on BNF by Archaea under environmental stresses typical to climate change. Here we report a survey of literature and DNA database to study N2-fixation among Archaea. A total of 37 Archaea belonging to Methanogens of the phylum Euryarchaeota within the class Methanococcus, Methanomicrobia Methanobacteria, and Methanotrophic ANME2 lineages either contain genes for BNF or are known to fix atmospheric N2. Archaea were found to have their nif genes arranged as clusters of 6-8 genes in a single operon. The genes code for commonly found Mo-nitrogenase while in some archaea the genes for alternative metal nitrogenases like vnf were also found. The nifHDK gene similarity matrices show that Archaea shared the highest similarity with the nifHDK gene of anaerobic Clostridium beijerinckii. Although there are various theories about the origin of N2-fixation in Archaea, the most acceptable is the origin of N2-fixation first in bacteria and its subsequent transfer to Archaea. Since Archaea can survive under extreme environmental conditions their role in BNF should be studied especially in soil under environmental stress.

Light-driven nitrogen fixation routes for green ammonia production

The global goal for decarbonization of the energy sector and the chemical industry could become a reality by a massive increase in renewable-based technologies. For this clean energy transition, the versatile green ammonia may play a key role in the future as a fossil-free fertilizer, long-term energy storage medium, chemical feedstock, and clean burning fuel for transportation and decentralized power generation. The high energy-intensive industrial ammonia production has triggered researchers to look for a step change in new synthetic approaches powered by renewable energies. This review provides a comprehensive comparison of light-mediated N2 fixation technologies for green ammonia production, including photocatalytic, photoelectrocatalytic, PV-electrocatalytic and photothermocatalytic routes. Since these approaches are still at laboratory scale, we examine the most recent developments and discuss the open challenges for future improvements. Last, we offer a technoeconomic comparison of current and emerging ammonia production technologies, highlighting costs, barriers, recommendations, and potential opportunities for the real development of the next generation of green ammonia solutions.

Synergistic N/F Dual-Doped MoC/C Catalyst Synthesized via Liquid Phase Plasma for Sustainable Ammonia Production

NH3 is a versatile solution for the storage and distribution of sustainable energy, offering high energy density and promising applications as a renewable hydrogen carrier. However, electrochemical NH3 synthesis under ambient conditions remains challenging, such as low selectivity and efficiency, owing to the inertness of N≡N and competing reactions. In this study, a catalyst (MoC/NFC) comprising molybdenum carbide evenly dispersed on carbon doped with N and F heteroatoms was successfully synthesized using liquid-phase plasma. The MoC/NFC catalyst exhibited a maximum NH3 yield of 115 μg h-1 mg-1cat. with a faradaic efficiency of 1.15% at -0.7 V vs reversible hydrogen electrode in 0.1 M KOH electrolyte. Pyridinic- and pyrrolic-N atoms adjacent to the carbon pores served as active sites for N2 adsorption and enabled N2 triple bond cleavage. In addition, F doping contributed to N2 activation owing to the high electronegativity of 3.98, resulting in the attraction of more electrons. These findings demonstrate a significant advancement in the development of efficient catalysts for electrochemical ammonia synthesis, potentially paving the way for scalable and sustainable NH3 production methods that can support the growing demand for renewable energy storage solutions.

Unlocking the Nitrogen Reduction Electrocatalyst with a Dual-Metal-Boron System: From High-Throughput Screening to Machine Learning

Recently, dual-metal catalysts have attracted much attention due to their abundant active sites and tunable chemical properties. On the other hand, metal borides have been widely applied in splitting the inert chemical bonds in small molecules (such as N2) because of their excellent catalytic performances. As a combination of the above two systems, in this work, 11 kinds of transition metal atoms (TM = Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Mo, and W) were selected to embed in boron-doped graphene (BG) to construct 66 dual-metal-boron systems, and their performances toward the N2 reduction reaction (NRR) were examined using first-principles simulations. Our results revealed that such a dual-TM@BG system exhibits excellent thermodynamic and electrochemical stabilities, which facilitate the experimental synthesis. In particular, Fe-Fe- and Fe-Co-doped BG exhibit excellent performance for NRR, with the limiting potentials of -0.29 and -0.32 V, respectively, and both of them exhibit inhibitory effects on the H2 evolution reaction. Remarkably, the microkinetic modeling analysis revealed that the turnover frequency for the NH3 production on FeFe@BG reaches up to 7.27 × 108 s-1 site-1 at 700 K and 100 bar, which further confirms its ultrafast reaction rate. In addition, the machine learning method was employed to further understand the catalytic mechanism, and it is found that the NRR performances of dual-TM@BG catalysts are closely related to the sum of radii of two TM atoms. Therefore, our work not only proposed two promising electrocatalysts for NRR but also verified the feasibility for the application of a dual-metal-boron system in NRR.

Enhanced electrochemical nitrate reduction to ammonia with nanostructured Mo2C on carbon nanotube-reduced graphene oxide hybrid support

The electrochemical nitrate reduction reaction (NO3-RR) is emerging as a promising method for ammonia production under ambient conditions while simultaneously addressing nitrate pollution. Due to the complexity of NO3-RR, which involves multi-electron/proton transfer and competes with the hydrogen evolution reaction (HER), the development of efficient electrocatalysts with high activity and stability is crucial. In this study, we report the use of Mo2C nanoparticles homogeneously dispersed on a carbon nanotube-reduced graphene oxide hybrid support (Mo2C/CNT-RGO) as an effective electrocatalyst for NO3-RR. The three-dimensional CNT-RGO hybrid provides a large surface area for electrolyte contact, enhanced electrical conductivity, and prevents the aggregation of Mo2C nanoparticles. Consequently, the Mo2C/CNT-RGO electrocatalyst demonstrated high NO3-RR performance, achieving a maximum NH3 production rate of 5.23 mg h-1 cm-2 with a faradaic efficiency of 95.9%. Mo2C/CNT-RGO also exhibited excellent long-term stability during consecutive cycling tests. This work presents a promising strategy for developing high-performance and durable NO3-RR electrocatalysts.

Electrochemical kinetic fingerprinting of single-molecule coordinations in confined nanopores

Metal centers are essential for enzyme catalysis, stabilizing the active site, facilitating electron transfer, and maintaining the structure through coordination with amino acids. In this study, K238H-AeL nanopores with histidine sites were designed as single-molecule reactors for the measurement of single-molecule coordination reactions. The coordination mechanism of Au(III) with histidine and glutamate in biological nanopore confined space was explored. Specifically, Au(III) interacts with the nitrogen (N) atom in the histidine imidazole ring of the K238H-AeL nanopore and the oxygen (O) atom in glutamate to form a stable K238H-Au-Cl2 complex. The formation mechanism of this complex was further validated through single-molecule nanopore analysis, mass spectrometry, and molecular dynamics simulations. Introducing histidine and negative charge amino acids with carboxyl group into different positions within the nanopore revealed that the formation of the histidine-Au coordination bond in the confined space requires a suitable distance between the ligand and the central metal atom. By analyzing the association and dissociation rates of the single Au(III) ion under the applied voltages, it was found that a confined nanopore increased the bonding rate constant of Au(III)-histidine coordination reactions by around 10-100 times compared to that in the bulk solution and the optimal voltage for single-molecule. Therefore, nanopore techniques for tracking single-molecule reactions could offer valuable insights into designing metalloenzymes in metal-catalyzed organic reactions.

Bionic Design of Iron-Doped MoSe2 Catalyst for Efficient Nitrogen Fixation

The catalytic system of biological nitrogen fixation in nature primarily relies on the "FeMo cofactor" within nitrogenase enzymes. Inspired by this natural structure, we have designed a bionic inorganic counterpart, iron-doped MoSe2, for the efficient electroreduction of dinitrogen to ammonia. The introduced Fe dopant significantly enhances nitrogen fixation activity of MoSe2. Furthermore, we constructed a heterostructure catalyst, the Fe-MoSe2/Mo2C with more versatile Mo valence states. The heterostructured electrocatalyst achieves an ammonia production rate of 3.38 μg cm-2 h-1, and a Faradaic efficiency of 30.8 %, which is ~5 fold higher than that of pristine MoSe2. This study presents a novel approach for designing bionic nitrogen fixation electrocatalysts.

Diatomic Active Sites Embedded Graphyne as Electrocatalysts for Ammonia Synthesis

Ammonia (NH3) is a vital chemical compound in industry and agriculture, and the electrochemical nitrogen reduction reaction (eNRR) is considered a promising approach for NH3 synthesis. However, the development of eNRR faces the challenge of high overpotential and low Faradaic efficiency. In this work, graphyne (GY) is anchored by 3d, 4d, and 5d dual transition metal atoms to form diatomic catalysts (DACs) and is roundly investigated as an electrocatalyst for eNRR via density functional theory calculations. Due to the protrusion of anchored metal atoms, the active sites of GY are better exposed compared to other substrates, exhibiting higher activity. Through four-step hierarchical high-throughput screening (ΔG*N2 < 0 eV, ΔG*N2 → *N2H < 0.4 eV, ΔG*NH2 → *NH3 < 0.4 eV, and ΔG*N2 < ΔG*H), the number of selected catalysts in each step is 325, 240, 145, and 20, respectively. Considering a series of factors, including stability, initial potential, and selectivity, 13 kinds of eligible catalysts are identified. Optimal eNRR paths studies show that the best catalyst Mn2@GY features no onset potential. For the three catalysts (Mn2@GY, Ir2@GY, and RhOs@GY), the onset potentials of the most favorable eNRR pathways are -0.07, -0.12, and -0.17 V, respectively. The excellent catalytic activity can be credited to the effective charge transfer and orbital interaction between the active site and adsorbed N2. Our work demonstrates the significance of DACs for ammonia synthesis and provides a paradigm for the study of DACs even for other important reactions.

Fe3O4 nanostructure films as solar-thermal conversion materials for ammonia synthesis

Here, we report that black photothermal materials elevate solar heating temperatures across high solar absorption and low infrared radiation. Fe3O4 nanostructure films can be heated to 350 °C under light irradiation, and this system shows effective visible-light-driven ammonia synthesis production of 3677 μg g-1 h-1 under gas-solid phase catalysis without noble metals.

Mechanism of Dinitrogen Photoactivation by P2PPhFe Complexes: Thermodynamic and Kinetic Computational Studies

The P2PPhFe(N2)(H)2 catalyst showed a significant ammonia yield under light irradiation. However, under thermal conditions, the hydrogen evolution reaction (HER) is favored over the nitrogen reduction reaction (N2RR), making P2PPhFe(N2)(H)2 an ideal system for studying the competition between both reactions. In this study, we used a series of computational tools to elucidate the photochemical reaction mechanism for the N2RR and thermal pathways leading to the HER with this catalyst. We calculated the energy profile for each transformation and estimated the rate constants for each step. Our results, which are consistent with experimental observations, indicate that photoinduced H2 elimination from P2PPhFe(N2)(H)2 promotes the formation of P2PPhFe(N2)2, which is on-path for N2RR. However, this elimination process is kinetically hindered due to high-energy barriers. Furthermore, our calculations reveal enhanced dinitrogen activation upon the conversion of P2PPhFe(N2)(H)2 to P2PPhFe(N2)2.

Bi2Ti2O7 Quantum Dots for Efficient Photocatalytic Fixation of Nitrogen to Ammonia: Impacts of Shallow Energy Levels

Photocatalytic fixation of nitrogen to ammonia represents an attractive alternative to the Haber-Bosch process under ambient conditions, and the performance can be enhanced by defect engineering of the photocatalysts, in particular, formation of shallow energy levels due to oxygen vacancies that can significantly facilitate the adsorption and activation of nitrogen. This calls for deliberate size engineering of the photocatalysts. In the present study, pyrochlore Bi2Ti2O7 quantum dots and (bulk-like) nanosheets are prepared hydrothermally by using bismuth nitrate and titanium sulfate as the precursors. Despite a similar oxygen vacancy concentration, the quantum dots exhibit a drastically enhanced photocatalytic performance toward nitrogen fixation, at a rate of 332.03 µmol g-1 h-1, which is 77 times higher than that of the nanosheet counterpart. Spectroscopic and computational studies based on density functional theory calculations show that the shallow levels arising from oxygen vacancies in the Bi2Ti2O7 quantum dots, in conjunction with the moderately constrained quantum confinement effect, facilitate the chemical adsorption and activation of nitrogen.

Enhancing Compatibility of Two-Step Tandem Catalytic Nitrate Reduction to Ammonia Over P-Cu/Co(OH)2

Electrochemical nitrate reduction reaction (NO3RR) is a promising approach to realize ammonia generation and wastewater treatment. However, the transformation from NO3 - to NH3 involves multiple proton-coupled electron transfer processes and by-products (NO2 -, H2, etc.), making high ammonia selectivity a challenge. Herein, a two-phase nanoflower P-Cu/Co(OH)2 electrocatalyst consisting of P-Cu clusters and P-Co(OH)2 nanosheets is designed to match the two-step tandem process (NO3 - to NO2 - and NO2 - to NH3) more compatible, avoiding excessive NO2 - accumulation and optimizing the whole tandem reaction. Focusing on the initial 2e- process, the inhibited *NO2 desorption on Cu sites in P-Cu gives rise to the more appropriate NO2 - released in electrolyte. Subsequently, P-Co(OH)2 exhibits a superior capacity for trapping and transforming the desorbed NO2 - during the latter 6e- process due to the thermodynamic advantage and contributions of active hydrogen. In 1 m KOH + 0.1 m NO3 -, P-Cu/Co(OH)2 leads to superior NH3 yield rate of 42.63 mg h- 1 cm- 2 and NH3 Faradaic efficiency of 97.04% at -0.4 V versus the reversible hydrogen electrode. Such a well-matched two-step process achieves remarkable NH3 synthesis performance from the perspective of optimizing the tandem catalytic reaction, offering a novel guideline for the design of NO3RR electrocatalysts.

Two-Dimensional MOF Constructed by a Binuclear-Copper Motif for High-Performance Electrocatalytic NO Reduction to NH3

Ambient electrochemical NO reduction presents a dual solution for sustainable NO reduction and NH3 synthesis. However, their complex kinetics and energy demands necessitate high-performance electrocatalysts to ensure effective and selective process outcomes. Herein, we report that a two-dimensional Cu-based metal-organic framework (MOF), {[Cu(HL)]·H2O} n , (Cu-OUC, H3L = 5-(2'-carboxylphenoxy)isophthalic acid) acts as a stable electrocatalyst with high efficiency for NO-to-NH3 conversion. Electrochemical experimental studies showed that in 0.1 M K2SO4 solution, the as-prepared Cu-OUC achieved a peak Faradaic efficiency of 96.91% and a notable NH3 yield as high as 3415.82 μg h-1 mg-1. The Zn-NO battery in aqueous solution can produce electricity possessing a power density of 2.04 mW cm-2 while simultaneously achieving an NH3 yield of 616.92 μg h-1 mg-1. Theoretical calculations revealed that the surface of Cu-OUC effectively facilitates NO activation through a two-way charge transfer mechanism of "electron acceptance and donation", with the *NO formation step being the potential-determining stage. The study pioneers the use of a MOF as an electrocatalyst for ambient NO-to-NH3 conversion.

Improved Nitrate-to-Ammonia Electrocatalysis through Hydrogen Poisoning Effects

Electrochemical conversion from nitrate to ammonia is a key step in sustainable ammonia production. However, it suffers from low productive efficiency or high energy consumption due to a lack of desired electrocatalysts. Here we report nickel cobalt phosphide (NiCoP) catalysts for nitrate-to-ammonia electrocatalysis that display a record-high catalytic current density of -702±7 mA cm-2, ammonia production rate of 5415±26 mmol gcat -1 h-1 and Faraday efficiency of 99.7±0.2 % at -0.3 V vs. RHE, affording the estimated energy consumption as low as 22.7 kWh kgammonia -1. Theoretical and experimental results reveal that these catalysts benefit from hydrogen poisoning effects, which leave behind catalytically inert adsorbed hydrogen species (HI*) at Co-hollow sites and thereupon enable ideally reactive HII* at secondary Co-P sites. The dimerization between HI* and HII* for H2 evolution is blocked due to the catalytic inertia of HI* thereby the HII* drives nitrate hydrogenation timely. With these catalysts, the continuous ammonia production is further shown in an electrolyser with a real energy consumption of 18.9 kWh kgammonia -1.

Rapid Fabrication of N-, Cu-, and Co-Doped Electrodes with Strong Electronic Coupling by Cold Plasma for Electrocatalytic Reduction of Nitrate to Ammonia

Electrochemical NOx- reduction (NOxRR) is a sustainable technology for ammonia synthesis. The development of a simple, fast, and economical catalytic electrode preparation technique is crucial for large-scale ammonia synthesis. Herein, we propose a plate-to-plate DBD plasma strategy to synthesize the catalytic electrodes M-N/CP (M = Cu, Co, Ni, CuCo, and CuNi), achieving in suit codoping of N and bimetals on carbon paper (CP) at room temperature within 3 h. N-doping improves the metal loading and the NOxRR performance by forming N-M bonds. The electronic coupling and synergistic effect of Cu and Co sites facilitate the relay conversion of NO3- to NO2- to NH3. Notably, the NO3- removal efficiency of CuCo-N/CP reaches 82%, with NH3 yield rate of 346 μg h-1 cm-2, and the faradaic efficiency is as high as 86% at -0.58 V vs RHE, which remains competitive in terms of NOxRR performance. Importantly, wet flue gas denitrification and desulfurization coupled with electrocatalytic reduction can convert NOx and SO2 to (NH4)2SO4, Additionally, the maneuverability of plasma technology offers the potential for batch preparation of CuCo-N/CP electrodes for electrochemically driven wet denitrification wastewater valorization.

Electrocatalytic Dinitrogen Reduction to Ammonia Using Easily Reducible N-Fused Cobalt Porphyrins

Single-site molecular electrocatalysts, especially those that perform catalytic conversion of N2 to NH3 under mild conditions, are highly desirable to derive fundamental structure-activity relations and as potential alternatives to the current energy-consuming Haber-Bosch ammonia production process. Combining theoretical calculations with experimental evidence, it has been shown that easily reducible cobalt porphyrins catalyze the six-electron, six-proton reduction of dinitrogen to NH3 at neutral pH and under ambient conditions. Two easily reducible N-fused cobalt porphyrins - CoNHF and CoNHF(Br)2 - reveal NRR activity with Faradic efficiencies between 6-7.5 % with ammonia yield rates of 300-340 μmol g-1 h-1. Contrary to this, much harder-to-reduce N-fused porphyrins - CoNHF(Ph)2 and CoNHF(PE)2 - reveal no NRR activity. The present study highlights the significance of tuning the redox and structural properties of single-site NRR electrocatalysts for improved NRR activity under mild conditions.

Highly Efficient Electrocatalytic Nitrate Reduction to Ammonia: Group VIII-Based Catalysts

The accumulation of nitrates in the environment causes serious health and environmental problems. The electrochemical nitrate reduction reaction (e-NO3RR) has received attention for its ability to convert nitrate to value-added ammonia with renewable energy. The key to effective catalytic efficiency is the choice of materials. Group VIII-based catalysts demonstrate great potential for application in e-NO3RR because of their high activity, low cost, and good electron transfer capability. This review summarizes the Group VIII catalysts, including monatomic, bimetallic, oxides, phosphides, and other composites. On this basis, strategies to enhance the intrinsic activity of the catalysts through coordination environment modulation, synergistic effects, defect engineering and hybridization are discussed. Meanwhile, the ammonia recovery process is summarized. Finally, the current research status in this field is prospected and summarized. This review aims to realize the large-scale application of nitrate electrocatalytic reduction in industrial wastewater.

Advances in designing efficient electrocatalysts for nitrate reduction from a theoretical perspective

Ammonia (NH3), an important raw material for producing fertilizers and useful chemicals, plays a crucial role in modern human society. As the Haber-Bosch process is energy- and emission-intensive, it is critical to develop a green and energy-efficient route for massive NH3 production under ambient conditions. The electrochemical nitrate reduction reaction to ammonia (eNO3-RR) is a potential way for producing NH3 while harmonizing the nitrogen cycle. In this feature article, we summarize the advances in designing eNO3-RR electrocatalysts from a theoretical perspective. First, the mechanisms and pathways of the eNO3-RR are summarized. Then, the recently developed electrocatalysts, including Cu-based catalysts, single-atom catalysts (SACs), dual-atom catalysts (DACs), and MXene catalysts, are categorically discussed. Finally, the challenges and prospects of designing highly efficient eNO3-RR catalysts through theoretical simulations are discussed. This feature article will provide valuable guidance for the future development of advanced eNO3-RR electrocatalysts for NH3 production.

Enabling Sustainable Ammonia Synthesis: From Nitrogen Activation Strategies to Emerging Materials

Ammonia (NH3) is one of the most important precursors of various chemicals and fertilizers. Given that ammonia synthesis via the traditional Haber-Bosch process requires high temperatures and pressures, it is critical to explore effective strategies and catalysts for ammonia synthesis under mild reaction conditions. Although electrocatalysis and photocatalysis can convert N2 to NH3 under mild conditions, their efficiencies and production scales are still far from the requirements for industrialization. Thermal catalysis has been proven to be the most direct and effective approach for ammonia synthesis. Over the past few decades, significant efforts have been made to develop novel catalysts capable of nitrogen fixation and ammonia generation via thermal catalytic processes. In parallel with catalyst exploration, new strategies such as self-electron donation, hydride fixation, hydridic hydrogen reduction, and anionic vacancy promotion have also been explored to moderate the operating conditions and improve the catalytic efficiency of ammonia synthesis. In this review, the emergence of new materials and strategies for promoting N2 activation and NH3 formation during thermal catalysis is briefly summarized. Moreover, challenges and prospects are proposed for the future development of thermal catalytic ammonia synthesis.

Structural evolution and catalytic mechanisms of perovskite oxides in electrocatalysis

Electrocatalysis plays a pivotal role in driving the progress of modern technologies and industrial processes such as energy conversion and emission reduction. Perovskite oxides, an important family of electrocatalysts, have garnered substantial attention in diverse catalytic reactions because of their highly tunable composition and structure, as well as their considerable activity and stability. This review delves into the mechanisms of electrocatalytic reactions that use perovskite oxides as electrocatalysts, while also providing a comprehensive summary of the potential key factors that influence catalytic activity across various reactions. Furthermore, this review offers an overview of advanced characterizations used for studying catalytic mechanisms and proposes approaches to designing highly efficient perovskite oxide electrocatalysts.

Exploring Nitrogen Reduction Reaction Mechanisms with Graphyne-Confined Single-Atom Catalysts: A Computational Study Incorporating Electrode Potential and pH

This study reconciles discrepancies between practical electrochemical conditions and theoretical density functional theory (DFT) frameworks, evaluating three graphyne-confined single-atom catalysts (Mo-TEB, Mo@GY, and Mo@GDY). Using both constant charge models in vacuum and constant potential models with continuum implicit solvation, we closely mimic real-world electrochemical environments. Our findings highlight the crucial role of explicitly incorporating electrode potential and pH in the constant potential model, providing enhanced insights into the nitrogen reduction reaction (NRR) mechanisms. Notably, the superior NRR performance of Mo-TEB is attributed to the d-band center's proximity to the Fermi level and enhanced magnetic moments at the atomic center. This research advances our understanding of graphyne-confined single-atom catalysts as effective NRR platforms and underscores the significance of the constant potential model for accurate DFT studies of electrochemical reactions.

Recent progress on Ti-based catalysts in the electrochemical synthesis of ammonia

Electrochemical ammonia synthesis presents a sustainable alternative, offering the potential for enhanced energy efficiency and environmental benefits compared to the conventional Haber-Bosch process. In recent years, the electrocatalytic reduction of nitrate to ammonia (NO3-RR) has emerged as a crucial approach for achieving sustainable NH3 production. To enhance energy efficiency and successfully convert NO3- to NH3, it is essential to investigate cost-effective electrocatalysts that provide high Faraday efficiency and demonstrate adequate stability. Ti-based materials are considered ideal candidates as catalysts due to their environmental friendliness and robust stability. This review initially summarizes the nitrate reduction reaction pathway and concisely discusses the impact of the potential intermediates and reaction steps on the overall reaction efficiency and product selectivity. Subsequently, an overview of the fundamental characteristics of Ti and TiO2 is presented. Additionally, the research process on Ti-based electrocatalysts in the electrochemical reduction of nitrate for ammonia synthesis is summarized. Finally, the design strategies, such as heteroatom doping and the introduction of oxygen vacancies, to enhance catalytic efficiency and selectivity are presented. Through this comprehensive review, we endeavor to furnish researchers with the most recent insights into the application of titanium-based electrocatalysts in nitrate reduction reactions and to stimulate innovative thought processes on the electrocatalytic synthesis of ammonia.

Reductive Inner-Sphere Electrosynthesis of Ammonia via a Nonelectrocatalytic Outer-Sphere Redox

Electrochemistry of outer-sphere redox molecules involves an essentially intact primary coordination sphere with minimal secondary sphere adjustments, resulting in very fast electron transfer events even without a noble metal-based electrocatalyst. Departing from conventional electrocatalytic paradigms, we incorporate these minimal reaction coordinate adjustments of outer-sphere species to stimulate the electrocatalysis of energetically challenging inner-sphere substrates. Through this approach, we are able to show an intricate 8e- and 9H+ transfer inner-sphere reductive electrocatalysis at almost half the energy input of a conventional inner-sphere electron donor. This methodology of employing outer-sphere redox species has the potential to notably improve the cost and energy benefits in electrochemical transformations involving fundamental substrates such as water, CO2, N2, and many more.

Rational design of bimetallic MBene for efficient electrocatalytic nitrogen reduction

Electrocatalytic nitrogen reduction reaction (NRR) is one of the most promising approaches to achieving green and efficient NH3 production. However, the designs of efficient NRR catalysts with high activity and selectivity still are severely hampered by inherent linear scaling relations among the adsorption energies of NRR intermediates. Herein, the properties of ten M3B4 type MBenes have been initially investigated for efficient N2 activation and reduction to NH3via first-principles calculations. We highlight that Cr3B4 MBene possesses remarkable NRR activity with a record-low limiting potential (-0.13 V). Then, this work proposes descriptor-based design principles that can effectively evaluate the catalytic activity of MBenes, which have been further employed to design bimetallic M2M'B4 MBenes. As a result, 5 promising candidates including Ti2YB4, V2YB4, V2MoB4, Nb2YB4, and Nb2CrB4 with excellent NRR performance have been extracted from 20 bimetallic MBenes. Further analysis illuminates that constructing bimetallic MBenes can selectively tune the adsorption strength of NHNH2** and NH2NH2**, and break the linear scaling relations between their adsorption energies, rendering them ideal for NRR. This work not only pioneers the application of MBenes as efficient NRR catalysts but also proposes rational design principles for boosting their catalytic performance.

Ru3@Mo2CO2 MXene single-cluster catalyst for highly efficient N2-to-NH3 conversion

Single-cluster catalysts (SCCs) representing structurally well-defined metal clusters anchored on support tend to exhibit tunable catalytic performance for complex redox reactions in heterogeneous catalysis. Here we report a theoretical study on an SCC of Ru3@Mo2CO2 MXene for N2-to-NH3 thermal conversion. Our results show that Ru3@Mo2CO2 can effectively activate N2 and promotes its conversion to NH3 through an association mechanism, in which the rate-determining step of NH2* + H* → NH3* has a low energy barrier of 1.29 eV. Notably, with the assistance of Mo2CO2 support, the positively charged Ru3 cluster active site can effectively adsorb and activate N2, leading to 0.74 |e| charge transfer from Ru3@Mo2CO2 to the adsorbed N2. The supported Ru3 also acts as an electron reservoir to regulate the charge transfer for various intermediate steps of ammonia synthesis. Microkinetic analysis shows that the turnover frequency of the N2-to-NH3 conversion on Ru3@Mo2CO2 is as high as 1.45 × 10-2 s-1 site-1 at a selected thermodynamic condition of 48 bar and 700 K, the performance of which even surpasses that of the Ru B5 site and Fe3/θ-Al2O3(010) reported before. Our work provides a theoretical understanding of the high stability and catalytic mechanism of Ru3@Mo2CO2 and guidance for further designing and fabricating MXene-based metal SCCs for ammonia synthesis under mild conditions.

Atomic Molybdenum Nanomaterials for Electrocatalysis

As a sustainable energy technology, electrocatalytic energy conversion requires electrocatalysts, which greatly motivates the exploitation of high-performance electrocatalysts based on nonprecious metals. Molybdenum-based nanomaterials have demonstrated promise as electrocatalysts because of their unique physiochemical and electronic properties. Among them, atomic Mo catalysts, also called Mo-based single-atom catalysts (Mo-SACs), have the most accessible active sites and tunable microenvironments and are thrivingly explored in various electrochemical conversion reactions. A timely review of such rapidly developing topics is necessary to provide guidance for further exploration of optimized Mo-SACs toward electrochemical energy technologies. In this review, recent advances in the synthetic strategies for Mo-SACs are highlighted, focusing on the microenvironment engineering of Mo atoms. Then, the representative achievements of their applications in various electrocatalytic reactions involving the N2, H2O, and CO2 cycles are summarized by combining experimental and computational results. Finally, prospects for the future development of Mo-SACs in electrocatalysis are provided and the key challenges that require further investigation and optimization are highlighted.

Optimizing the Lattice Nitrogen Coordination to Break the Performance Limitation of Metal Nitrides for Electrocatalytic Nitrogen Reduction

Metal nitrides (MNs) are attracting enormous attention in the electrocatalytic nitrogen reduction reaction (NRR) because of their rich lattice nitrogen (Nlat) and the unique ability of Nlat vacancies to activate N2. However, continuing controversy exists on whether MNs are catalytically active for NRR or produce NH3 via the reductive decomposition of Nlat without N2 activation in the in situ electrochemical conditions, let alone the rational design of high-performance MN catalysts. Herein, we focus on the common rocksalt-type MN(100) catalysts and establish a quantitative theoretical framework based on the first-principles microkinetic simulations to resolve these puzzles. The results show that the Mars-van Krevelen mechanism is kinetically more favorable to drive the NRR on a majority of MNs, in which Nlat plays a pivotal role in achieving the Volmer process and N2 activation. In terms of stability, activity, and selectivity, we find that MN(100) with moderate formation energy of Nlat vacancy (E vac) can achieve maximum activity and maintain electrochemical stability, while low- or high-E vac ones are either unstable or catalytically less active. Unfortunately, owing to the five-coordinate structural feature of Nlat on rocksalt-type MN(100), this maximum activity is limited to a yield of NH3 of only ∼10-15 mol s-1 cm-2. Intriguingly, we identify a volcano-type activity-regulating role of the local structural features of Nlat and show that the four-coordinate Nlat can exhibit optimal activity and overcome the performance limitation, while less coordinated Nlat fails. This work provides, arguably for the first time, an in-depth theoretical insight into the activity and stability paradox of MNs for NRR and underlines the importance of reaction kinetic assessment in comparison with the prevailing simple thermodynamic analysis.

Integrated electrocatalytic synthesis of ammonium nitrate from dilute NO gas on metal organic frameworks-modified gas diffusion electrodes

The electrocatalytic conversion of NO offers a promising technology for not only removing the air pollutant but also synthesizing valuable chemicals. We design an integrated-electrocatalysis cell featuring metal organic framework (MOF)-modified gas diffusion electrodes for simultaneous capture of NO and generation of NH4NO3 under low-concentration NO flow conditions. Using 2% NO gas, the modified cathode exhibits a higher NH4+ yield and Faradaic efficiency than an unmodified cathode. Notably, the modified cathode shows a twofold increase in NH4+ production with 20 ppm NO gas supply. Theoretical calculations predict favorable transfer of adsorbed NO from the adsorption layer to the catalyst layer, which is experimentally confirmed by enhanced NO mass transfer from gas to electrolyte across the modified electrode. The adsorption layer-modified anode also exhibits a higher NO3- yield for NO electro-oxidation compared to the unmodified electrode under low NO concentration flow. Among various integrated-cell configurations, a single-chamber setup produces a higher NH4NO3 yield than a double-chamber setup. Furthermore, a higher NO utilization efficiency is obtained with a single-gasline operation mode, where the NO-containing gas flows sequentially from the cathode to the anode.

Precious-Metal-Free Mo-MXene Catalyst Enabling Facile Ammonia Synthesis Via Dual Sites Bridged by H-Spillover

To date, NH3 synthesis under mild conditions is largely confined to precious Ru catalysts, while nonprecious metal (NPM) catalysts are confronted with the challenge of low catalytic activity due to the inverse relationship between the N2 dissociation barrier and NHx (x = 1-3) desorption energy. Herein, we demonstrate NPM (Co, Ni, and Re)-mediated Mo2CTx MXene (where Tx denotes the OH group) to achieve efficient NH3 synthesis under mild conditions. In particular, the NH3 synthesis rate over Re/Mo2CTx and Ni/Mo2CTx can reach 22.4 and 21.5 mmol g-1 h-1 at 400 °C and 1 MPa, respectively, higher than that of NPM-based catalysts and Cs-Ru/MgO ever reported. Experimental and theoretical studies reveal that Mo4+ over Mo2CTx has a strong ability for N2 activation; thus, the rate-determining step is shifted from conventional N2 dissociation to NH2* formation. NPM is mainly responsible for H2 activation, and the high reactivity of spillover hydrogen and electron transfer from NPM to the N-rich Mo2CTx surface can efficiently facilitate nitrogen hydrogenation and the subsequent desorption of NH3. With the synergistic effect of the dual active sites bridged by H-spillover, the NPM-mediated Mo2CTx catalysts circumvent the major obstacle, making NH3 synthesis under mild conditions efficient.

Transition-metal-based Catalysts for Electrochemical Synthesis of Ammonia by Nitrogen Reduction Reaction: Advancing the Green Ammonia Economy

Ammonia (NH3), a cornerstone in the chemical industry, has historically been pivotal for producing various valuable products, notably fertilizers. Its significance is further underscored in the modern energy landscape, where NH3 is seen as a promising medium for hydrogen storage and transportation. However, the conventional Haber-Bosch process, which accounts for approximately 170 million ton of NH3 produced globally each year, is energy-intensive and environmentally damaging. The electrochemical nitrogen reduction reaction (NRR) emerges as a sustainable alternative that operates in ambient conditions and uses renewable energy sources. Despite its potential, the NRR faces challenges, including the inherent stability of nitrogen and its competition with the hydrogen evolution reaction. Transition metals, especially ruthenium (Ru) and molybdenum (Mo), have demonstrated promise as catalysts, enhancing the efficiency of the NRR. Ru excels in catalytic activity, while Mo offers robustness. Strategies like heteroatom doping are being pursued to mitigate NRR challenges, especially the competing hydrogen evolution reaction. This review delves into the advancements of Ru and Mo-based catalysts for electrochemical ammonia synthesis, elucidating the NRR mechanisms, and championing the transition towards a greener ammonia economy. It also seeks to elucidate the core principles underpinning the NRR mechanism. This shift aims not only to address challenges inherent to traditional production methods but also to align with the overarching goals of global sustainability.

Catalysts with Trimetallic Sites on Graphene-like C2N for Electrocatalytic Nitrogen Reduction Reaction: A Theoretical Investigation

Electrocatalytic nitrogen reduction reaction (NRR) is a green and highly efficient way to replace the industrial Haber-Bosch process. Herein, clusters consisting of three transition metal atoms loaded on C2N as NRR electrocatalysts are investigated using density functional theory (DFT). Meanwhile, Ca was introduced as a promoter and the role of Ca in NRR was investigated. It was found that Ca anchored to the catalyst can act as an electron donor and effectively promote the activation of N2 on M3. In both M3@C2N and M3Ca@C2N (M=Fe, Co, Ni), the limiting potential (UL) is less negative than that of the Ru(0001) surface and has the ability to suppress the competitive hydrogen evolution reaction (HER). Among them, Fe3@C2N is suggested to be the most promising candidate for NRR with high thermal stability, strong N2 adsorption ability, low limiting potential, and good NRR selectivity. The concepts of trimetallic sites and alkaline earth metal promoters in this work provide theoretical guidance for the rational design of atomically active sites in electrocatalytic NRR.

Photoelectrocatalytic Synthesis of Urea from Carbon Dioxide and Nitrate over a Cu2O Photocathode

Transformation of carbon dioxide and nitrate ions into urea offers an attractive route for both nitrogen fertilizer production and environmental remediation. However, achieving this transformation under mild conditions remains challenging. Herein, we report an efficient photoelectrochemical method for urea synthesis by co-reduction of carbon dioxide and nitrate ion over a Cu2O photocathode, delivering urea formation rate of 29.71±2.20 μmol g-1 h-1 and Faradaic efficiency (FE) of 12.90±1.15 % at low external potential (-0.017 V vs. reversible hydrogen electrode). Experimental data combined with theoretical calculations suggest that the adsorbed CO* and NO2* species are the key intermediates, and associated C-N coupling is the rate-determining step. This work demonstrates that Cu2O is an efficient catalyst to drive co-reduction of CO2 and NO3 - to urea under light irradiation with low external potential, showing great opportunity of photoelectrocatalysis as a sustainable tool for value-added chemical synthesis.

Designing N, P-doped graphene surface-supported Mo single-atom catalysts for efficient conversion of nitrogen into ammonia: a computational guideline

Tuning the surroundings of single-atom catalysts (SACs) has been recognized as a successful approach to enhance their electrocatalytic efficiency. In this study, we utilized density functional theory (DFT) computations to systematically investigate how the coordination environment influences the catalytic performance of individual molybdenum atoms for the nitrogen reduction reaction (NRR) to NH3. Upon comparing an extensive array of coordination combinations, Mo-based SACs were found to feature a distinctive N, P-dual coordination. Specifically, MoN3P1G demonstrates superior performance in the conversion of nitrogen into ammonia with an exceptionally low limiting potential (-0.64 V). This MoN3P1G catalyst preferably follows the distal pathway, with the initial hydrogenation step (*N2 → *NNH) being the rate-determining step. Additionally, MoN3P1G exhibits the ability to suppress competing H2 production, showcases high thermodynamic stability, and holds significant promise for experimental preparation. These findings not only contribute to diversifying the SAC family through localized coordination control but also present cost-effective strategies for enhancing sustainable NH3 production.

Electrosynthesis of Ammonia from Nitrate Using a Self-Activated Carbon Fiber Paper

While electrochemically upcycling nitrate wastes to valuable ammonia is considered a very promising pathway for tackling the environmental and energy challenges underlying the nitrogen cycle, the effective catalysts involved are mainly limited to metal-based materials. Here, we report that commercial carbon fiber paper, which is a classical current collector and is typically assumed to be electrochemically inert, can be significantly activated during the reaction. As a result, it shows a high NH3 Faradaic efficiency of 87.39% at an industrial-level current density of 300 mA cm-2 for over 90 h of continuous operation, with a NH3 production rate of as high as 1.22 mmol cm-2 h-1. Through experimental and theoretical analysis, the in situ-formed oxygen functional groups are demonstrated to be responsible for the NO3RR performance. Among them, the C-O-C group is finally identified as the active center, which lowers the thermodynamic energy barrier and simultaneously improves the hydrogenation kinetics. Moreover, high-purity NH4Cl and NH3·H2O were obtained by coupling the NO3RR with an air-stripping approach, providing an effective way for converting nitrate waste into high-value-added NH3 products.

Deep Electron Redistributions Induced by Dual Junctions Facilitating Electroreduction of Dilute Nitrate to Ammonia

The electronic states of metal catalysts can be redistributed by the rectifying contact between metal and semiconductor e.g., N-doped carbon (NC), while the interfacial regulation degree is very limited. Herein, a deep electronic state regulation is achieved by constructing a novel double-heterojunctional Co/Co3O4@NC catalyst containing Co/Co3O4 and Co3O4/NC heterojunctions. When used for dilute electrochemical NO3 - reduction reaction (NO3RR), the as-prepared Co/Co3O4@NC exhibits an outstanding Faradaic efficiency for NH3 formation (FENH3) of 97.9%, -0.4 V versus RHE and significant NH3 yield of 303.5 mmol h-1 gcat -1 at -0.6 V at extremely low nitrate concentrations (100 ppm NO3 --N). Experimental and theoretical results reveal that the dual junctions of Co/Co3O4 and Co3O4/NC drive a unidirectional electron transfer from Co to NC (Co→Co3O4→NC), resulting in electron-deficient Co atoms. The electron-deficient Co promotes NO3 - adsorption, the rate-determining step (RDS) for NO3RR, facilitating the dilute NO3RR to NH3. The design strategy provides a novel reference for unidirectional multistage regulation of metal electronic states boosting electrochemical dilute NO3RR, which opens up an avenue for deep electronic state regulation of electrocatalyst breaking the limitation of the electronic regulation degree by rectifying contact.

Multivalent Sulfur Vacancy-Rich NiCo2S4@MnO2 Urchin-Like Heterostructures for Ambient Electrochemical N2 Reduction to NH3

Innovative advances in the exploitation of effective electrocatalytic materials for the reduction of nitrogen (N2) to ammonia (NH3) are highly required for the sustainable production of fertilizers and zero-carbon emission fuel. In order to achieve zero-carbon footprints and renewable NH3 production, electrochemical N2 reduction reaction (NRR) provides a favorable energy-saving alternative but it requires more active, efficient, and selective catalysts. In current work, sulfur vacancy (Sv)-rich NiCo2S4@MnO2 heterostructures are efficaciously fabricated via a facile hydrothermal approach followed by heat treatment. The urchin-like Sv-NiCo2S4@MnO2 heterostructures serve as cathodes, which demonstrate an optimal NH3 yield of 57.31 µg h-1 mgcat -1 and Faradaic efficiency of 20.55% at -0.2 V versus reversible hydrogen electrode (RHE) in basic electrolyte owing to the synergistic interactions between Sv-NiCo2S4 and MnO2. Density functional theory (DFT) simulation further verifies that Co-sites of urchin-like Sv-NiCo2S4@MnO2 heterostructures are beneficial to lowering the energy threshold for N2 adsorption and successive protonation. Distinctive micro/nano-architectures exhibit high NRR electrocatalytic activities that might motivate researchers to explore and concentrate on the development of heterostructures for ambient electrocatalytic NH3 generation.

Polynuclear Cobalt Cluster-Based Coordination Polymers for Efficient Nitrate-to-Ammonia Electroreduction

The electrocatalytic nitrate reduction reaction (NITRR) holds great promise for purifying wastewater and producing valuable ammonia (NH3). However, the lack of efficient electrocatalysts has impeded the achievement of highly selective NH3 synthesis from the NITRR. In this study, we report the design and synthesis of two polynuclear Co-cluster-based coordination polymers, {[Co2(TCPPDA)(H2O)5]·(H2O)9(DMF)} and {Co1.5(TCPPDA)[(CH3)2NH2]·(H2O)6(DMF)2} (namely, NJUZ-2 and NJUZ-3), which possess distinct coordination motifs with well-defined porosity, high-density catalytic sites, accessible mass transfer channels, and nanoconfined chemical environments. Benefitting from their intriguing multicore metal-organic coordination framework structures, NJUZ-2 and NJUZ-3 exhibit remarkable catalytic activities for the NITRR. At a potential of -0.8 V (vs. RHE) in an H-type cell, they achieve an optimal Faradaic efficiency of approximately 98.5% and high long-term durability for selective NH3 production. Furthermore, the electrocatalytic performance is well maintained even under strongly acidic conditions. When operated under an industrially relevant current density of 469.9 mA cm-2 in a flow cell, a high NH3 yield rate of up to 3370.6 mmol h-1 g-1cat. was observed at -0.5 V (vs. RHE), which is 20.1-fold higher than that obtained in H-type cells under the same conditions. Extensive experimental analyses, in combination with theoretical computations, reveal that the great enhancement of the NITRR activity is attributed to the preferential adsorption of NO3- and the reduction in energy input required for the hydrogenation of *NO3 and *NO2 intermediates.