Integration of Inkjet Printed Graphene as a Hole Transport Layer in Organic Solar Cells

This work demonstrates the green production of a graphene ink for inkjet printing and its use as a hole transport layer (HTL) in an organic solar cell. Graphene as an HTL improves the selective hole extraction at the anode and prevents charge recombination at the electronic interface and metal diffusion into the photoactive layer. Graphite was exfoliated in water, concentrated by iterative centrifugation, and characterized by Raman. The concentrated graphene ink was incorporated into inverted organic solar cells by inkjet printing on the active polymer in an ambient atmosphere. Argon plasma was used to enhance wetting of the polymer with the graphene ink during printing. The argon plasma treatment of the active polymer P3HT:PCBM was investigated by XPS, AFM and contact angle measurements. Efficiency and lifetime studies undertaken show that the device with graphene as HTL is fully functional and has good potential for an inkjet printable and flexible alternative to PEDOT:PSS.

Graphene-Iron Ore Tailings-Based Cementitious Composites with High Early Flexural Strength

Graphene is a two-dimensional nanomaterial with excellent mechanical, electrical and thermal properties. The application of graphene in cement-based materials has good prospects. However, the mechanical properties of cement-based materials are difficult to be significantly enhanced by ordinary graphene nanoplates. In this paper, nitrogen-doped graphene is first reported as an additive with dosages of 0.01, 0.02, 0.03, 0.04 and 0.05 wt.%, respectively, to prepare iron ore tailings-based cementitious composites. The iron ore tailings-based cementitious composite with 0.02 wt.% graphene shows an extremely high flexural strength of 15.05 MPa at 3 days, which is 134.4% higher than that of the iron ore tailings-based cementitious composite without graphene. The effects of graphene content and curing age on the flexural strength and microstructure of iron ore tailings-based cementitious composites were studied. In particular, the scanning electron microscope was adopted to observe the micromorphology of the composites. It is helpful to understand the graphene reinforcement mechanism for the high early flexural strength of iron ore tailings-based cementitious composites. By altering the morphology of iron ore tailings-based cementitious composites, graphene plays two roles in the composites. One role is to connect C-(A)-S-H gels, ettringite and other hydrated crystals to construct a three-dimensional structure. The other is to attract iron ore tailings distributed on its platform to enhance its flexural strength properties. These findings provide favorable guidance for the performance enhancement and mechanism replenishment of graphene-reinforced cementitious composites.

Electrochemical Synthesis of Hydrogen Peroxide Catalyzed by Carbon Nanotubes with Surface Co-NX Sites and Encapsulated Co Nanoparticles

The exploitation of M-N_X sites, where M is a transition metal atom, is widely regarded as an effective catalytic strategy to promote the oxygen reduction reaction (ORR). In addition, some studies have shown that transition metal nanoparticles (M-NPs) coated with carbon layers can improve the reactivity of ORR and ameliorate the overpotential of the reaction. In this study, we synthesized carbon nanotubes with single-atom Co-N_X active sites, Co-NPs outside the tube, and Co-NPs wrapped in the tube by the complexation-pyrolysis synthesis method and explored the role of the particles and Co-N_X sites through different pickling steps. The catalyst synthesized with the new stratagem in this study shows outstanding selectivity and also ORR activity. Furthermore, a natural air diffusion electrode fabricated using this material can produce H₂O₂ at 323 mg L^-1 h^-1 under neutral conditions without oxygen aeration.

A Review on the Production Methods and Applications of Graphene-Based Materials

Graphene-based materials in the form of fibres, fabrics, films, and composite materials are the most widely investigated research domains because of their remarkable physicochemical and thermomechanical properties. In this era of scientific advancement, graphene has built the foundation of a new horizon of possibilities and received tremendous research focus in several application areas such as aerospace, energy, transportation, healthcare, agriculture, wastewater management, and wearable technology. Although graphene has been found to provide exceptional results in every application field, a massive proportion of research is still underway to configure required parameters to ensure the best possible outcomes from graphene-based materials. Until now, several review articles have been published to summarise the excellence of graphene and its derivatives, which focused mainly on a single application area of graphene. However, no single review is found to comprehensively study most used fabrication processes of graphene-based materials including their diversified and potential application areas. To address this genuine gap and ensure wider support for the upcoming research and investigations of this excellent material, this review aims to provide a snapshot of most used fabrication methods of graphene-based materials in the form of pure and composite fibres, graphene-based composite materials conjugated with polymers, and fibres. This study also provides a clear perspective of large-scale production feasibility and application areas of graphene-based materials in all forms.

Chemical Vapour Deposition of Graphene-Synthesis, Characterisation, and Applications: A Review

Graphene as the 2D material with extraordinary properties has attracted the interest of research communities to master the synthesis of this remarkable material at a large scale without sacrificing the quality. Although Top-Down and Bottom-Up approaches produce graphene of different quality, chemical vapour deposition (CVD) stands as the most promising technique. This review details the leading CVD methods for graphene growth, including hot-wall, cold-wall and plasma-enhanced CVD. The role of process conditions and growth substrates on the nucleation and growth of graphene film are thoroughly discussed. The essential characterisation techniques in the study of CVD-grown graphene are reported, highlighting the characteristics of a sample which can be extracted from those techniques. This review also offers a brief overview of the applications to which CVD-grown graphene is well-suited, drawing particular attention to its potential in the sectors of energy and electronic devices.

Evolution of Temperature-Driven Interfacial Wettability and Surface Energy Properties on Hierarchically Structured Porous Superhydrophobic Pseudoboehmite Thin Films

Interaction of water on heterogeneous nonwetting interfaces has fascinated researchers' attention for wider applications. Herein, we report the evolution of hierarchical micro-/nanostructures on superhydrophobic pseudoboehmite surfaces created from amorphous Al₂O₃ films and unraveled their temperature-driven wettability and surface energy properties. The influence of hot water immersion temperature on the dissolution-reprecipitation mechanism and the surface geometry of the Al₂O₃ film have been extensively analyzed, which helped in attaining the optimal Cassie-Baxter state. The evolution of pseudoboehmite films has been structurally characterized using grazing incidence X-ray diffraction, field-emission scanning electron microscopy, high-resolution transmission electron microscopy, X-ray photoelectron spectroscopy and atomic force microscopy. Interfacial surface energy components on the structured superhydrophobic surface exhibited a very low surface energy of ∼4.6 mN/m at room temperature and ultrahigh water contact angle >175°. The interaction between water droplets on the nonwetting surface was comprehended and correlated to the temperature-dependent surface energy properties. The surface energy and wettability of the structured pseudoboehmite superhydrophobic surface exhibited an inverse behavior as a function of temperature. Interestingly, the superhydrophobic surface exhibited "Leidenfrost effect" below the boiling point of water (67 °C), which is further correlated with the intermolecular forces, interfacial water molecules and surface-terminated groups. These high-temperature wetting transition studies could be potentially valuable for solid-liquid systems working at nonambient temperatures, and also this approach can pave new pathways for better understanding of the solid/liquid interfacial interactions on nanoengineered superhydrophobic surfaces.

A versatile route to edge-specific modifications to pristine graphene by electrophilic aromatic substitution

Electrophilic aromatic substitution produces edge-specific modifications to CVD graphene and graphene nanoplatelets that are suitable for specific attachment of biomolecules.

Pristine-Graphene-Supported Nitrogen-Doped Carbon Self-Assembled from Glucaminium-Based Ionic Liquids as Metal-Free Catalyst for Oxygen Evolution

For the first time, graphene-supported N-doped carbon (G@NC) with a high degree of N doping was synthesized by in situ self-assembly of a glucaminium-based ionic liquid on pristine graphene under hydrothermal conditions. This 2D, metal-free nanohybrid exhibited much higher catalytic activity than most reported metal-free catalysts for the oxygen evolution reaction (OER) and even state-of-the-art Ir- and Ru-based catalysts because the high content of graphitic N greatly increased the number of OER-active sites, the pristine graphene significantly promoted the OER activity of the C sites adjacent to the graphitic N atoms, and N-doped graphitic carbon remarkably enhanced the charge-transfer rate. This work not only creates a facile and economical approach to controllably fabricate pristine-graphene-supported carbon with a high N-doping level for the development of highly efficient metal-free OER catalysts but also provides insight into the mechanisms for both the in situ self-assembly and the high OER catalytic activity of G@NC.

Wafer-Scale Fabrication of Nitrogen-Doped Reduced Graphene Oxide with Enhanced Quaternary-N for High-Performance Photodetection

We demonstrated a simple and scalable fabrication route of a nitrogen-doped reduced graphene oxide (N-rGO) photodetector on an 8 in. wafer-scale. The N-rGO was prepared through in situ plasma treatment in an acetylene-ammonia atmosphere to achieve an n-type semiconductor with substantial formation of quaternary-N substituted into the graphene lattice. The morphology, structural, chemical composition, and electrical properties of the N-rGO were carefully characterized and used for the device fabrication. The N-rGO devices were fabricated in a simple metal-semiconductor-metal structure with unconventional metal-on-bottom configuration to promote high-performance photodetection. The N-rGO devices exhibited enhanced photoresponsivity as high as 0.68 A W^-1 at 1.0 V, which is about 2 orders of magnitude higher compared to a pristine graphene and wide-band photoinduced response from the visible to the near-infrared region with increasing sensitivity in the order of 785, 632.8, and 473 nm excitation wavelengths. We also further demonstrated a symmetric characteristic of the photoinduced response to any position of local laser excitation with respect to the electrodes. The excellent features of wafer-scale N-rGO devices suggest a promising route to merge the current silicon technology and two-dimensional materials for future optoelectronic devices.

Cross-plane conductance through a graphene/molecular monolayer/Au sandwich

The functionalities offered by single-molecule electrical junctions are yet to be translated into monolayer or few-layer molecular films, where making effective and reproducible electrical contact is one of the challenging bottlenecks. Here we take a significant step in this direction by demonstrating that excellent electrical contact can be made with a monolayer biphenyl-4,4'-dithiol (BPDT) molecular film, sandwiched between gold and graphene electrodes. This sandwich device structure is advantageous, because the current flows through the molecules to the gold substrate in a 'cross-plane' manner, perpendicular to the plane of graphene, yielding high-conductance devices. We elucidate the nature of the cross-plane graphene/molecule/Au transport using quantum transport calculations and introduce a simple analytical model, which captures generic features of the current-voltage characteristic. Asymmetry in junction properties results from the disparity in electrode electrical properties, the alignment of the BPDT HOMO-LUMO energy levels and the specific characteristics of the graphene electrode. The experimental observation of scalability of junction properties within the junction area, in combination with a theoretical description of the transmission probability of the thiol-graphene contact, demonstrates that between 10% and 100% of the molecules make contact with the electrodes, which is several orders of magnitude greater than that achieved to date in the literature.

Light-Induced Conformational Change of Uracil-Anchored Polythiophene-Regulating Thermo-Responsiveness

Tuning the electronic structure of a π-conjugated polymer from the responsive side chains is generally done to get desired optoelectronic properties, and it would be very fruitful when light is used as an exciting tool that can also affect the backbone chain conformation. For this purpose, polythiophene- g-poly-[ N-(6-methyluracilyl)- N, N-dimethylamino chloride]ethyl methacrylate (PTDU) is synthesized. On exposure to diffuse sunlight, the uracil moieties of the grafted chains cause the absorption maximum of PTDU solution to show gradual blue shift of 87 nm and a gradual blue shift of 46 nm in the emission maximum, quenching its fluorescence with time. These effects occur specifically at the absorption range of polythiophene (PT) chromophore on direct exposure of light of different wavelengths, and the optimum wavelength is found to be 420 nm. Impedance study suggests a decrease in charge transfer resistance upon exposure because of conformational change of PTDU. Theoretical study indicates that on exposure to visible light, uracil moieties move toward the backbone to facilitate photoinduced electron transfer between the PT and the uracil, attributing to the variation in optoelectronic properties. Morphological and light-scattering studies exhibit a decrease in particle size because of coiling of the PT backbone and squeezing of the grafted chain on light exposure. The transparent orange-colored PTDU solution becomes hazy with a hike in emission intensity on addition of sodium halides and becomes reversibly transparent or hazy on heating or cooling. The screening of cationic centers of PTDU by varying halide anion concentration tunes the phase transition temperature. Thus, the light-induced variation in the backbone conformation is responsible for tuning the optoelectronic properties and regulates the thermos-responsiveness of the PTDU solution in the presence of halide ions.

Chemistry below graphene: decoupling epitaxial graphene from metals by potential-controlled electrochemical oxidation

While high-quality defect-free epitaxial graphene can be efficiently grown on metal substrates, strong interaction with the supporting metal quenches its outstanding properties. Thus, protocols to transfer graphene to insulating substrates are obligatory, and these often severely impair graphene properties by the introduction of structural or chemical defects. Here we describe a simple and easily scalable general methodology to structurally and electronically decouple epitaxial graphene from Pt(111) and Ir(111) metal surfaces. A multi-technique characterization combined with ab-initio calculations was employed to fully explain the different steps involved in the process. It was shown that, after a controlled electrochemical oxidation process, a single-atom thick metal-hydroxide layer intercalates below graphene, decoupling it from the metal substrate. This decoupling process occurs without disrupting the morphology and electronic properties of graphene. The results suggest that suitably optimized electrochemical treatments may provide effective alternatives to current transfer protocols for graphene and other 2D materials on diverse metal surfaces.

Chemical sensors based on surface charge transfer

The focus of this review is an introduction to chemiresistive chemical sensors. The general concept of chemical sensors is briefly introduced, followed by different architectures of chemiresistive sensors and relevant materials. For several of the most common systems, the fabrication of the active materials used in such sensors and their properties are discussed. Furthermore, the sensing mechanism, advantages, and limitations of each group of chemiresistive sensors are briefly elaborated. Compared to electrochemical sensors, chemiresistive sensors have the key advantage of a simpler geometry, eliminating the need for a reference electrode. The performance of bulk chemiresistors can be improved upon by using freestanding ultra-thin films (nanomaterials) or field effect geometries. Both of those concepts have also been combined in a gateless geometry, where charge transport though a percolation network of nanomaterials is modulated via adsorbate doping.

High-quality PVD graphene growth by fullerene decomposition on Cu foils

We present a new protocol to grow large-area, high-quality single-layer graphene on Cu foils at relatively low temperatures. We use C₆₀ molecules evaporated in ultra high vacuum conditions as carbon source. This clean environment results in a strong reduction of oxygen-containing groups as depicted by X-ray photoelectron spectroscopy (XPS). Unzipping of C₆₀ is thermally promoted by annealing the substrate at 800ºC during evaporation. The graphene layer extends over areas larger than the Cu crystallite size, although it is changing its orientation with respect to the surface in the wrinkles and grain boundaries, producing a modulated ring in the low energy electron diffraction (LEED) pattern. This protocol is a self-limiting process leading exclusively to one single graphene layer. Raman spectroscopy confirms the high quality of the grown graphene. This layer exhibits an unperturbed Dirac-cone with a clear n-doping of 0.77 eV, which is caused by the interaction between graphene and substrate. Density functional theory (DFT) calculations show that this interaction can be induced by a coupling between graphene and substrate at specific points of the structure leading to a local sp³ configuration, which also contribute to the D-band in the Raman spectra.

Two zinc-aminoclays' in-vitro cytotoxicity assessment in HeLa cells and in-vivo embryotoxicity assay in zebrafish

Two zinc-aminoclays [ZnACs] with functionalized primary amines [(-CH₂)₃NH₂] were prepared by a simple sol-gel reaction using cationic metal precursors of ZnCl₂ and Zn(NO₃)₂ with 3-aminopropyl triethoxysilane [APTES] under ambient conditions. Due to the facile interaction of heavy metals with primary amine sites and Zn-related intrinsic antimicrobial activity, toxicity assays of ZnACs nanoparticles (NPs) prior to their environmental and human-health applications are essential. However, such reports remain rare. Thus, in the present study, a cell viability assay of in-vitro HeLa cells comparing ZnCl₂, Zn(NO₃)₂ salts, and ZnO (~50nm average diameter) NPs was performed. Interestingly, compared with the ZnCl₂, and Zn(NO₃)₂ salts, and ZnO NPs (18.73/18.12/51.49µg/mL and 18.12/15.19/46.10µg/mL of IC₅₀ values for 24 and 48h), the two ZnACs NPs exhibited the highest toxicity (IC₅₀ values of 21.18/18.36µg/mL and 18.37/17.09µg/mL for 24 and 48h, respectively), whose concentrations were calculated on Zn elemental composition. This might be due to the enhanced bioavailability and uptake into cells of ZnAC NPs themselves and their positively charged hydrophilicity by reactive oxygen species (ROS) generation, particularly as ZnACs exist in cationic NP's form, not in released Zn²⁺ ionic form (i.e., dissolved nanometal). However, in an in-vivo embryotoxicity assay in zebrafish, ZnACs and ZnO NPs showed toxic effects at 50-100µg/mL (corresponding to 37.88-75.76 of Zn wt% µg/mL). The hatching rate (%) of zebrafish was lowest for the ZnO NPs, particularly where ZnAC-[(NO₃)₂] is slightly more toxic than ZnAC-[Cl₂]. These results are all very pertinent to the issue of ZnACs' potential applications in the environmental and biomedical fields.

Co-SrCO3/N-doped carbon: a highly efficient hybrid electrocatalyst for the oxygen reduction reaction and Zn–air batteries

SrCO₃ with surface SrO was used to develop Co-SrCO₃/NC electrocatalysts with high performance for the ORR and Zn–air batteries.

CVD transfer-free graphene for sensing applications

The sp² carbon-based allotropes have been extensively exploited for the realization of gas sensors in the recent years because of their high conductivity and large specific surface area. A study on graphene that was synthetized by means of a novel transfer-free fabrication approach and is employed as sensing material is herein presented. Multilayer graphene was deposited by chemical vapour deposition (CVD) mediated by CMOS-compatible Mo. The utilized technique takes advantage of the absence of damage or contamination of the synthesized graphene, because there is no need for the transfer onto a substrate. Moreover, a proper pre-patterning of the Mo catalyst allows one to obtain graphene films with different shapes and dimensions. The sensing properties of the material have been investigated by exposing the devices to NO₂, NH₃ and CO, which have been selected because they are well-known hazardous substances. The concentration ranges have been chosen according to the conventional monitoring of these gases. The measurements have been carried out in humid N₂ environment, setting the flow rate at 500 sccm, the temperature at 25 °C and the relative humidity (RH) at 50%. An increase of the conductance response has been recorded upon exposure towards NO₂, whereas a decrease of the signal has been detected towards NH₃. The material appears totally insensitive towards CO. Finally, the sensing selectivity has been proven by evaluating and comparing the degree of adsorption and the interaction energies for NO₂ and NH₃ on graphene. The direct-growth approach for the synthesis of graphene opens a promising path towards diverse applicative scenarios, including the straightforward integration in electronic devices.

Perfluorodecyltrichlorosilane-based seed-layer for improved chemical vapour deposition of ultrathin hafnium dioxide films on graphene

We investigate the use of perfluorodecyltrichlorosilane-based self-assembled monolayer as seeding layer for chemical vapour deposition of HfO₂ on large area CVD graphene. The deposition and evolution of the FDTS-based seed layer is investigated by X-ray photoelectron spectroscopy, Auger electron spectroscopy, and transmission electron microscopy. Crystalline quality of graphene transferred from Cu is monitored during formation of the seed layer as well as the HfO₂ growth using Raman spectroscopy. We demonstrate that FDTS-based seed layer significantly improves nucleation of HfO₂ layers so that graphene can be coated in a conformal way with HfO₂ layers as thin as 10 nm. Proof-of-concept experiments on 200 mm wafers presented here validate applicability of the proposed approach to wafer scale graphene device fabrication.

Insights into the effects of metal nanostructuring and oxidation on the work function and charge transfer of metal/graphene hybrids

Graphene/metal heterojunctions are ubiquitous in graphene-based devices and, therefore, have attracted increasing interest of researchers. Indeed, the literature on the field reports apparently contradictory results about the effect of a metal on graphene doping. Here, we elucidate the effect of metal nanostructuring and oxidation on the metal work function (WF) and, consequently, on the charge transfer and doping of graphene/metal hybrids. We show that nanostructuring and oxidation of metals provide a valid support to frame WF and doping variation in metal/graphene hybrids. Chemical vapour-deposited monolayer graphene has been transferred onto a variety of metal surfaces, including d-metals, such as Ag, Au, and Cu, and sp-metals, such as Al and Ga, configured as thin films or nanoparticle (NP) ensembles of various average sizes. The metal-induced charge transfer and the doping of graphene have been investigated using Kelvin probe force microscopy (KPFM), and corroborated by Raman spectroscopy and plasmonic ellipsometric spectroscopy. We show that when the appropriate WF of the metal is considered, without any assumption, taking into account WF variations by nanostructure and/or oxidation, a linear relationship between the metal WF and the doping of graphene is found. Specifically, for all metals, nanostructuring lowers the metal WF. In addition, using gold as an example, a critical metal nanoparticle size is found at which the direction of charge transfer, and consequently graphene doping, is inverted.

Photoactive hybrid material based on pyrene functionalized PbS nanocrystals decorating CVD monolayer graphene

A simple and facile solution-based procedure is implemented for decorating a large area, monolayer graphene film, grown by chemical vapor deposition, with size-tunable light absorbing colloidal PbS nanocrystals (NCs). The hybrid is obtained by exposing a large area graphene film to a solution of 1-pyrene butyric acid surface coated PbS NCs, obtained by a capping exchange procedure onto presynthesized organic-capped NCs. The results demonstrate that at the interface, multiple and cooperative π-π stacking interactions promoted by the pyrene ligand coordinating the NC surface lead to a successful anchoring of the nano-objects on the graphene platform which concomitantly preserves its aromatic structure. Interligand interactions provide organization of the nano-objects in highly interconnected nanostructured multilayer coatings, where the NCs retain geometry and composition. The resulting hybrid exhibits a sheet resistance lower than that of bare graphene, which is explained in terms of electronic communication in the hybrid, due to the interconnection of the NC film and to a hole transfer from photoexcited PbS NCs to graphene, channelled at the interface by pyrene. Such a direct electron coupling makes the manufactured hybrid material an interesting component for optoelectronics, sensors and for optical communication and information technology.

Spectroscopic and microscopic studies of self-assembled nc-Si/a-SiC thin films grown by low pressure high density spontaneous plasma processing

In view of suitable applications in the window layer of nc-Si p-i-n solar cells in superstrate configuration, the growth of nc-Si/a-SiC composite films was studied, considering the trade-off relation between individual characteristics of its a-SiC component to provide a wide optical-gap and electrically conducting nc-Si component to simultaneously retain enough crystalline linkages to facilitate proper crystallization to the i-nc-Si absorber-layer during its subsequent growth. Self-assembled nc-Si/a-SiC thin films were spontaneously grown by low-pressure planar inductively coupled plasma CVD, operating in electromagnetic mode, providing high atomic-H density. Spectroscopic simulations of ellipsometry and Raman data, and systematic chemical and structural analysis by XPS, TEM, SEM and AFM were performed. Corresponding to optimized inclusion of C essentially incorporated as Si-C bonds in the network, the optical-gap of the a-SiC component widened, void fraction including the incubation layer thickness reduced. While the bulk crystallinity decreased only marginally, Si-ncs diminished in size with narrower distribution and increased number density. With enhanced C-incorporation, formation of C-C bonds in abundance deteriorates the Si continuous bonding network and persuades growth of an amorphous dominated silicon-carbon heterostructure containing high-density tiny Si-ncs. Stimulated nanocrystallization identified in the Si-network, induced by a limited amount of carbon incorporation, makes the material most suitable for applications in nc-Si solar cells. The novelty of the present work is to enable spontaneous growth of self-assembled superior quality nc-Si/a-SiC thin films and simultaneous spectroscopic simulation-based optimization of properties for utilization in devices.