Enhanced Modification of Fast-Growing Wood: Application and Evaluation of Castor Oil-Based Unsaturated Polyester Resin

A type of multifunctional maleic acid ester monomer (COEGMA) was synthesized using castor oil as raw material, and green wood-plastic composites were prepared by chemically impregnating and curing the monomer into wood. The structure of the synthesized products at various stages was determined by FT-IR spectroscopy, 1H NMR, and GPC, and the curing experimental conditions were optimized. The results show that the water absorption of wood-plastic composites treated with COEGMA is reduced from the original 167.3% to less than 20%. The compressive strength has increased from 35.7 to 86.1 MPa, and the thermal stability has also increased by 40 °C. This research provides promising prospects for the development of environmentally friendly wood-plastic composites, especially as fossil resources become scarce and environmental pollution becomes more severe.

Simple magnesium alkoxides: synthesis, molecular structure, and catalytic behaviour in the ring-opening polymerization of lactide and macrolactones and in the copolymerization of maleic anhydride and propylene oxide

The synthesis of two chiral bulky alkoxide pro-ligands, 1-adamantyl-tert-butylphenylmethanol HOCAdtBuPh and 1-adamantylmethylphenylmethanol HOCAdMePh, is reported and their coordination chemistry with magnesium(II) is described and compared with the coordination chemistry of the previously reported achiral bulky alkoxide pro-ligand HOCtBu2Ph. Treatment of n-butyl-sec-butylmagnesium with two equivalents of the racemic mixture of HOCAdtBuPh led selectively to the formation of the mononuclear bis(alkoxide) complex Mg(OCAdtBuPh)2(THF)2. 1H NMR spectroscopy and X-ray crystallography suggested the selective formation of the C2-symmetric homochiral diastereomer Mg(OCRAdtBuPh)2(THF)2/Mg(OCSAdtBuPh)2(THF)2. In contrast, the less sterically encumbered HOCAdMePh led to the formation of dinuclear products indicating only partial alkyl group substitution. The mononuclear Mg(OCAdtBuPh)2(THF)2 complex was tested as a catalyst in different reactions for the synthesis of polyesters. In the ROP of lactide, Mg(OCAdtBuPh)2(THF)2 demonstrated very high activity, higher than that shown by Mg(OCtBu2Ph)2(THF)2, although with moderate control degrees. Both Mg(OCAdtBuPh)2(THF)2 and Mg(OCtBu2Ph)2(THF)2 were found to be very effective in the polymerization of macrolactones such as ω-pentadecalactone (PDL) and ω-6-hexadecenlactone (HDL) also under mild reaction conditions that are generally prohibitive for these substrates. The same catalysts demonstrated efficient ring-opening copolymerization (ROCOP) of propylene oxide (PO) and maleic anhydride (MA) to produce poly(propylene maleate).

Novel Epoxidized Brazil Nut Oil as a Promising Plasticizing Agent for PLA

This work evaluates for the first time the potential of an environmentally friendly plasticizer derived from epoxidized Brazil nut oil (EBNO) for biopolymers, such as poly(lactic acid) (PLA). EBNO was used due to its high epoxy content, reaching an oxirane oxygen content of 4.22% after 8 h of epoxidation for a peroxide/oil ratio of 2:1. Melt extrusion was used to plasticize PLA formulations with different EBNO contents in the range of 0-10 phr. The effects of different amounts of EBNO in the PLA matrix were studied by performing mechanical, thermal, thermomechanical, and morphological characterizations. The tensile test demonstrated the feasibility of EBNO as a plasticizer for PLA by increasing the elongation at break by 70.9% for the plasticized PLA with 7.5 phr of EBNO content in comparison to the unplasticized PLA. The field-emission scanning electron microscopy (FESEM) of the fractured surfaces from the impact tests showed an increase in porosity and roughness in the areas with EBNO addition, which was characteristic of ductile failure. In addition, a disintegration test was performed, and no influence on the PLA biodegradation process was observed. The overall results demonstrate the ability of EBNO to compete with other commercial plasticizers in improving the ductile properties of PLA.

Adhesive and Self-Healing Polyurethanes with Tunable Multifunctionality

Many polyurethanes (PUs) are blood-contacting materials due to their good mechanical properties, fatigue resistance, cytocompatibility, biosafety, and relatively good hemocompatibility. Further functionalization of the PUs using chemical synthetic methods is especially attractive for expanding their applications. Herein, a series of catechol functionalized PU (C-PU-PTMEG) elastomers containing variable molecular weight of polytetramethylene ether glycol (PTMEG) soft segment are reported by stepwise polymerization and further introduction of catechol. Tailoring the molecular weight of PTMEG fragment enables a regulable catechol content, mobility of the chain segment, hydrogen bond and microphase separation of the C-PU-PTMEG elastomers, thus offering tunability of mechanical strength (such as breaking strength from 1.3 MPa to 5.7 MPa), adhesion, self-healing efficiency (from 14.9% to 96.7% within 2 hours), anticoagulant, antioxidation, anti-inflammatory properties and cellular growth behavior. As cardiovascular stent coatings, the C-PU-PTMEGs demonstrate enough flexibility to withstand deformation during the balloon dilation procedure. Of special importance is that the C-PU-PTMEG-coated surfaces show the ability to rapidly scavenge free radicals to maintain normal growth of endothelial cells, inhibit smooth muscle cell proliferation, mediate inflammatory response, and reduce thrombus formation. With the universality of surface adhesion and tunable multifunctionality, these novel C-PU-PTMEG elastomers should find potential usage in artificial heart valves and surface engineering of stents.

Synthesis and Evaluation of Thermoresponsive Renewable Lipid-Based Block Copolymers for Drug Delivery

Polymeric micelle forming from self-assembly of amphiphilic macromolecules is one of the most potent drug delivery systems. Fatty acids, naturally occurring hydrophobic lipid components, can be considered as potential candidates for the fabrication of block copolymer micelles. However, examples of synthesis of responsive block copolymers using renewable fatty acids are scarce. Herein, we report the synthesis, characterization and testing of block copolymer micelles composed of a renewable fatty-acid-based hydrophobic block and thermoresponsive hydrophilic block for controlled drug delivery. The block copolymers of functionalized fatty acid and poly(N-isopropylacrylamide) (PNIPAM) were prepared via consecutive microwave-assisted reversible addition fragmentation chain transfer (RAFT) polymerization. The block copolymers with variable hydrophobic block length self-assembled in aqueous media and formed spherical nanoparticles of ~30 nm with low critical micelle concentration (CMC). To demonstrate the proof-of-concept, carbamazepine (CBZ) was used as a hydrophobic model drug to evaluate the performance of these micelles as nanocarriers. The in vitro drug release tests were carried out below (25 °C) and above (37 °C) the lower critical solution temperature (LCST) of the block copolymer. The drug release showed obvious temperature-triggered response and an accelerated drug release at 37 °C.

Utility of Chemical Upcycling in Transforming Postconsumer PET to PBT-Based Thermoplastic Copolyesters Containing a Renewable Fatty-Acid-Derived Soft Block

Thermoplastic copolyesters (TPCs) are important structural components in countless high performance applications that require excellent thermal stability and outstanding mechanical integrity. Segmented multiblock architectures are often employed for the most demanding applications, in which semicrystalline segments of poly(butylene terephthalate) (PBT) are combined with various low T _g soft blocks. These segmented copolymers are nearly always synthesized from pristine feedstocks that are derived from fossil-fuel sources. In this work, we show a straightforward, one-pot synthetic approach to prepare TPCs starting from high-molar mass poly(ethylene terephthalate) recyclate (rPET) combined with a hydrophobic fatty acid dimer diol flexible segment. Transesterification is exploited to create a multiblock architecture. The high molar mass and segment distribution are elucidated by detailed size-exclusion chromatography and proton and carbon nuclear magnetic resonance spectroscopy. It is also shown that rPET can be chemically converted to PBT through a molecular exchange, in which the ethylene glycol is substituted by introducing 1,4-butane diol. A series of copolymers with various compositions was prepared with either PET or PBT segments and the final thermal properties and mechanical performance is compared between the two different constructs. Ultimately, PBT-based TPCs crystallize faster and exhibit a higher modulus over the range of explored compositions, making them ideal for applications that require injection molding. This represents an ideal, sustainable approach to making conventional TPCs, utilizing recyclate and biobased components to produce high performance polymer constructs via an easily accessible upcycling route.

Synthesis of Thermoplastic Polyurethanes Containing Bio-Based Polyester Polyol and Their Fiber Property

Among the starting materials of thermoplastic polyurethanes (TPUs), it was confirmed that succinic acid-based polyester biopolyols having different molecular weights (M_n = 1000, 2000, and 4000) affect the physicochemical properties of the final polymer significantly. Bio-TPUs synthesized through a solvent-free one-shot polymerization process were synthesized with a polyester polyol, 1,4 butanediol (BDO), and 4,4′-methylene diphenyl diisocyanate (MDI) in a molar ratio of 1:1:2. As a control group, one typical petroleum-based TPU was synthesized and characterized along with other bio-based TPUs. Representative petroleum-based and bio-based TPUs synthesized were manufactured as monofilaments with a diameter of about 0.2 mm through an extrusion process with different draw ratios (4, 5, and 6 times). The molecular weight and structural properties of the TPUs were characterized by GPC and FT-IR analysis and thermal characterization by DSC and TGA analysis. Petroleum-based TPU and bio-based TPU having the same molecular weight soft segment (SS) tended to have similar molecular weight and hard segment (HS) content. TPUs with high HS content had excellent thermal stability, enabling stable extrusion of TPUs. In addition, it was confirmed that the bio-based TPU fibers produced in this way had a tensile strength corresponding to the physical properties of petroleum-based TPU fibers and an excellent elastic recovery rate of almost 100 %. These results indicate the application potential of bio-TPU.

Thiol-Ene Coupling of High Oleic Sunflower Oil towards Application in the Modification of Flexible Polyurethane Foams

High oleic sunflower oil-based polyol was obtained by thiol-ene coupling and applied in the preparation of flexible polyurethane foams. The photochemically initiated thiol-ene click reaction was carried out under UV irradiation using 2-mercaptoethanol. Bio-based polyol with hydroxyl value of 201.4 mg KOH/g was used as 30 wt% substituent of petrochemical polyether polyol in the formulations of flexible foams. Both reference foams, as well as foams modified with bio-based polyol, were formulated to have various isocyanate indices (0.85, 0.95, 1.05). Flexible foams were compared in terms of their thermomechanical properties and analyzed using FT-IR and SEM microscopy. Modification with bio-based polyol resulted in foams with superior compression properties, higher support factor, and lower resilience than reference foams. TGA and FT-IR curves confirmed the presence of urethane/urea and ether linkages in the polyurethane matrix. Moreover, double glass transition temperature corresponding to soft and hard segments of polyurethane was observed by DSC proving the phase-separated morphology.

Fatty Acids and their Derivatives as Renewable Platform Molecules for the Chemical Industry

Oils and fats of vegetable and animal origin remain an important renewable feedstock for the chemical industry. Their industrial use has increased during the last 10 years from 31 to 51 million tonnes annually. Remarkable achievements made in the field of oleochemistry in this timeframe are summarized herein, including the reduction of fatty esters to ethers, the selective oxidation and oxidative cleavage of C-C double bonds, the synthesis of alkyl-branched fatty compounds, the isomerizing hydroformylation and alkoxycarbonylation, and olefin metathesis. The use of oleochemicals for the synthesis of a great variety of polymeric materials has increased tremendously, too. In addition to lipases and phospholipases, other enzymes have found their way into biocatalytic oleochemistry. Important achievements have also generated new oil qualities in existing crop plants or by using microorganisms optimized by metabolic engineering.

Construction of Mechanically Reinforced Thermoplastic Polyurethane from Carbon Dioxide-Based Poly(ether carbonate) Polyols via Coordination Cross-Linking

Using carbon dioxide-based poly(propylene ether carbonate) diol (PPCD), isophorone diisocyanate (IPDI), dimethylolbutyric acid (DMBA), ferric chloride (FeCl₃), and ethylene glycol (EG) as the main raw materials, a novel thermoplastic polyurethane (TPU) is prepared through coordination of FeCl₃ and DMBA to obtain TPU containing coordination enhancement directly. The Fourier transform infrared spectroscopy, ¹H NMR, gel permeation chromatography, UV−Vis spectroscopy, tensile testing, dynamic mechanical analysis, X-ray diffraction, differential scanning calorimetry, and thermogravimetric analysis were explored to characterize chemical structures and mechanical properties of as-prepared TPU. With the increasing addition of FeCl₃, the tensile strength and modulus of TPU increase. Although the elongation at break decreases, it still maintains a high level. Dynamic mechanical analysis shows that the glass-transition temperature moves to a high temperature gradually along with the increasing addition of FeCl₃. X-ray diffraction results indicate that TPUs reinforced with FeCl₃ or not are amorphous polymers. That FeCl₃ coordinates with DMBA first is an effective strategy of getting TPU, which is effective and convenient in the industry without the separation of intermediate products. This work confirms that such Lewis acids as FeCl₃ can improve and adjust the properties of TPU contenting coordination structures with an in-situ reaction in a low addition amount, which expands their applications in industry and engineering areas.

Comparative Study of the Properties of Plasticized Polylactic Acid with Maleinized Hemp Seed Oil and a Novel Maleinized Brazil Nut Seed Oil

In this study, for the first time, Brazil nut seed oil was chemically modified with maleic anhydride to obtain maleinized Brazil nut seed oil (MBNO). The same process was developed to obtain maleinized hemp seed oil (MHO). The use of MBNO and MHO was studied as bio-based plasticizers by incorporating them with different contents ranging from 0 to 10 phr in a polylactic acid (PLA) matrix. By means of mechanical, thermal and thermomechanical characterization techniques, the properties of the different formulations were studied to evaluate the plasticizing effect of the MBNO and MHO. With the addition of both plasticizers, a significant increase in ductile properties was observed, reaching an increase in elongation at break of 643% with 7.5 phr MBNO and 771% with 10 phr MHO compared to neat PLA. In addition, it has been observed that the mechanical resistant properties do not decrease, since the oils enhance the crystallization of PLA by increasing the free volume between its chains and counteracting the effect. Finally, a disintegration test was carried out under thermophilic conditions at 58 °C for 27 days, demonstrating that the incorporation of MHO and MBNO does not significantly affect the biodegradability of neat PLA.

Recent Advances in Fabrication of Non-Isocyanate Polyurethane-Based Composite Materials

Polyurethanes (PUs) are a significant group of polymeric materials that, due to their outstanding mechanical, chemical, and physical properties, are used in a wide range of applications. Conventionally, PUs are obtained in polyaddition reactions between diisocyanates and polyols. Due to the toxicity of isocyanate raw materials and their synthesis method utilizing phosgene, new cleaner synthetic routes for polyurethanes without using isocyanates have attracted increasing attention in recent years. Among different attempts to replace the conventional process, polyaddition of cyclic carbonates (CCs) and polyfunctional amines seems to be the most promising way to obtain non-isocyanate polyurethanes (NIPUs) or, more precisely, polyhydroxyurethanes (PHUs), while primary and secondary –OH groups are being formed alongside urethane linkages. Such an approach eliminates hazardous chemical compounds from the synthesis and leads to the fabrication of polymeric materials with unique and tunable properties. The main advantages include better chemical, mechanical, and thermal resistance, and the process itself is invulnerable to moisture, which is an essential technological feature. NIPUs can be modified via copolymerization or used as matrices to fabricate polymer composites with different additives, similar to their conventional counterparts. Hence, non-isocyanate polyurethanes are a new class of environmentally friendly polymeric materials. Many papers on the matter above have been published, including both original research and extensive reviews. However, they do not provide collected information on NIPU composites fabrication and processing. Hence, this review describes the latest progress in non-isocyanate polyurethane synthesis, modification, and finally processing. While focusing primarily on the carbonate/amine route, methods of obtaining NIPU are described, and their properties are presented. Ways of incorporating various compounds into NIPU matrices are characterized by the role of PHU materials in copolymeric materials or as an additive. Finally, diverse processing methods of non-isocyanate polyurethanes are presented, including electrospinning or 3D printing.

The Green Approach to the Synthesis of Bio-Based Thermoplastic Polyurethane Elastomers with Partially Bio-Based Hard Blocks

Bio-based polymeric materials and green routes for their preparation are current issues of many research works. In this work, we used the diisocyanate mixture based on partially bio-based diisocyanate origin and typical petrochemical diisocyanate for the preparation of novel bio-based thermoplastic polyurethane elastomers (bio-TPUs). We studied the influence of the diisocyanate mixture composition on the chemical structure, thermal, thermomechanical, and mechanical properties of obtained bio-TPUs. Diisocyanate mixture and bio-based 1,4-butanediol (as a low molecular chain extender) created bio-based hard blocks (HS). The diisocyanate mixture contained up to 75 wt % of partially bio-based diisocyanate. It is worth mentioning that the structure and amount of HS impact the phase separation, processing, thermal or mechanical properties of polyurethanes. The soft blocks (SS) in the bio-TPU’s materials were built from α,ω-oligo(ethylene-butylene adipate) diol. Hereby, bio-TPUs differed in hard segments content (c.a. 30; 34; 40, and 53%). We found that already increase of bio-based diisocyanate content of the bio-TPU impact the changes in their thermal stability which was measured by TGA. Based on DMTA results we observed changes in the viscoelastic behavior of bio-TPUs. The DSC analysis revealed decreasing in glass transition temperature and melting temperature of hard segments. In general, obtained materials were characterized by good mechanical properties. The results confirmed the validity of undertaken research problem related to obtaining bio-TPUs consist of bio-based hard building blocks. The application of partially bio-based diisocyanate mixtures and bio-based chain extender for bio-TPU synthesis leads to sustainable chemistry. Therefore the total level of “green carbons” increases with the increase of bio-based diisocyanate content in the bio-TPU structure. Obtained results constitute promising data for further works related to the preparation of fully bio-based thermoplastic polyurethane elastomers and development in the field of bio-based polymeric materials.

Synthesis and properties of biobased copolyamides based on polyamide 10T and polyamide 56 through one-pot polymerization

A series of new biobased polyamide 10T-co-56 were synthesized with various comonomer compositions by a one-pot polycondensation reaction, and their structures, crystalline and melting behavior were systematically investigated.

A Review of Wood Biomass-Based Fatty Acids and Rosin Acids Use in Polymeric Materials

In recent decades, vegetable oils as a potential replacement for petrochemical materials have been extensively studied. Tall oil (crude tall oil, distilled tall oil, tall oil fatty acids, and rosin acids) is a good source to be turned into polymeric materials. Unlike vegetable oils, tall oil is considered as lignocellulosic plant biomass waste and is considered to be the second-generation raw material, thus it is not competing with the food and feed chain. The main purpose of this review article is to identify in what kind of polymeric materials wood biomass-based fatty acids and rosin acids have been applied and their impact on the properties.

Improving thermal and mechanical properties of biomass-based polymers using structurally ordered polyesters from ricinoleic acid and 4-hydroxycinnamic acids

Biomass-based copolymers with alternating ricinoleic acid and 4-hydroxycinnamic acid derivatives (p-coumaric acid, ferulic acid, and sinapinic acid) exhibit a repeating structure based on soft and hard segments, derived from ricinoleic and 4-hydroxycinnamic acids, respectively. To achieve this alternating sequence, copolymers were synthesised by the self-condensation of hetero-dimeric monomers derived by the pre-coupling of methyl ricinolate and 4-hydroxycinnamic acid. The glass transition temperature (T_g) was observed to increase as the number of methoxy groups on the main chain increased; the T_g values of poly(coumaric acid-alt-ricinoleic acid), poly(ferulic acid-alt-ricinoleic acid), and poly(sinapinic acid-alt-ricinoleic acid) are −15 °C, −4 °C, and 24 °C respectively, 58 °C, 69 °C, and 97 °C higher than that of poly(ricinoleic acid). The polymers were processed into highly flexible, visually transparent films. Among them, poly(sinapinic acid-alt-ricinoleic acid) bearing two methoxy groups on each cinnamoyl unit, is mechanically the strongest polymer, with an elastic modulus of 126.5 MPa and a tensile strength at break of 15.47 MPa.

The synthesis of structurally ordered polyesters derived from ricinoleic acid and 4-hydroxycinnamic acids improves the thermal and mechanical properties.

From Glucose to Polymers: A Continuous Chemoenzymatic Process

Efforts to synthesize degradable polymers from renewable resources are deterred by technical and economic challenges; especially, the conversion of natural building blocks into polymerizable monomers is inefficient, requiring multistep synthesis and chromatographic purification. Herein we report a chemoenzymatic process to address these challenges. An enzymatic reaction system was designed that allows for regioselective functional group transformation, efficiently converting glucose into a polymerizable monomer in quantitative yield, thus removing the need for chromatographic purification. With this key success, we further designed a continuous, three-step process, which enabled the synthesis of a sugar polymer, sugar poly(orthoester), directly from glucose in high yield (73 % from glucose). This work may provide a proof-of-concept in developing technically and economically viable approaches to address the many issues associated with current petroleum-based polymers.

Cellulose nanocrystal/plant oil polymer composites with hydrophobicity, humidity-sensitivity, and high wet strength

The preparation of high-performance cellulose nanocrystals (CNCs)/plant oil-derived polymer composites is still a challenge, due to their poor compatibility. Here, by designing amide groups and epoxy groups on sunflower oil derived polymers, appropriate interfacial hydrogen bond interactions between the polymers and CNCs were constructed, where CNCs were homogenously dispersed in polymer matrix. Tensile tests and DMA results revealed that the incorporation of CNCs into sunflower oil derived epoxy polymers significantly enhanced the tensile strength and storage modulus. More importantly, nanocomposites with 50 wt% CNCs are still hydrophobic, which not only show a fast and reversible humidity induced modulus switch, but also exhibit high wet strength (19.9 MPa) after equilibrium water adsorption. The present work revealed that proper designed CNCs/plant oil polymer nanocomposites are good candidates for high performance and functional materials, which are able to replace petroleum-based materials in various fields.

Novel Bio-Based Epoxy Thermosets Based on Triglycidyl Phloroglucinol Prepared by Thiol-Epoxy Reaction

The pure trifunctional glycidyl monomer from phloroglucinol (3EPO-Ph) was synthesized and used as feedstock in the preparation of novel bio-based thermosets by thiol-epoxy curing. The monomer was crosslinked with different commercially available thiols: tetrafunctional thiol (PETMP), trifunctional thiol (TTMP) and an aromatic dithiol (TBBT) as curing agents in the presence of a base. As catalyst, two different commercial catalysts: LC-80 and 4-(N,N-dimethylamino) pyridine (DMAP) and a synthetic catalyst, imidazolium tetraphenylborate (base generator, BG) were employed. The curing of the reactive mixtures was studied by using DSC and the obtained materials by means of differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and dynamic mechanical thermal analysis (DMTA). The results revealed that only the formulations catalyzed by BG showed a latent character. Already prepared thermosetting materials showed excellent thermal, thermomechanical and mechanical properties, with a high transparency. In addition to that, when compared with the diglycidyl ether of bisphenol A (DGEBA)/PETMP material, the thermosets prepared from the triglycidyl derivative of phloroglucinol have better final characteristics and therefore this derivative can be considered as a partial or total renewable substitute of DGEBA in technological applications.

Structural insight into the viscoelastic behaviour of elastomeric polyesters: effect of the nature of fatty acid side chains and the degree of unsaturation

Increase in unsaturation of fatty acid side chains results in decrease of zero-shear viscosity, degree of entanglement and resilience of polyesters. Cis double bonds act as kinks that prevent molecular packing of polymer chains.

Catalytic developments in the epoxidation of vegetable oils and the analysis methods of epoxidized products

Functionalization of vegetable oils (VOs) including edible, non-edible, and waste cooking oil (WCOs) to epoxides (EVOs) is receiving great attention by many researchers from academia and industry because they are renewable, versatile, sustainable, non-toxic, and eco-friendly, and they can partially or totally replace harmful phthalate plasticizers. The epoxidation of VOs on an industrial scale has already been developed by the homogeneous catalytic system using peracids. Due to the drawbacks of this method, other systems including acidic ion exchange resins, polyoxometalates, and enzymes are becoming alternative catalysts for the epoxidation reaction. We have reviewed all these catalytic systems including their benefits and drawbacks, reaction mechanisms, intensification of each system in different ways as well as the physicochemical properties of VOs and EVOs and new findings in recent years. Finally, the current methods including titrimetric methods as well as ATR-FTIR and 1H NMR for determination of conversion, epoxidation, and selectivity of epoxidized vegetable oils (EVOs) are also briefly described.

Design, Preparation, and Evaluation of a Novel Elastomer with Bio-Based Diethyl Itaconate Aiming at High-Temperature Oil Resistance

A novel elastomer poly(diethyl itaconate-co-butyl acrylate-co-ethyl acrylate-co-glycidyl methacrylate) (PDEBEG) was designed and synthesized by redox emulsion polymerization based on bio-based diethyl itaconate, butyl acrylate, ethyl acrylate, and glycidyl methacrylate. The PDEBEG has a number average molecular weight of more than 200,000 and the yield is up to 96%. It is easy to control the glass transition temperature of the PDEBEG, which is ranged from −25.2 to −0.8 °C, by adjusting the monomer ratio. We prepared PDEBEG/CB composites by mixing PDEBEG with carbon black N330 and studied the oil resistance of the composites. The results show that the tensile strength and the elongation at break of the composites with 10 wt% diethyl itaconate can reach up to 14.5 MPa and 305%, respectively. The mechanical properties and high-temperature oil resistance of the composites are superior to that of the commercially available acrylate rubber AR72LS.

POLYMERIC BIOMATERIALS FOR SCAFFOLD-BASED BONE REGENERATIVE ENGINEERING

Reconstruction of large bone defects resulting from trauma, neoplasm, or infection is a challenging problem in reconstructive surgery. The need for bone grafting has been increasing steadily partly because of our enhanced capability to salvage limbs after major bone loss. Engineered bone graft substitutes can have advantages such as lack of antigenicity, high availability, and varying properties depending on the applications chosen for use. These favorable attributes have contributed to the rise of scaffold-based polymeric tissue regeneration. Critical components in the scaffold-based polymeric regenerative engineering approach often include 1. The existence of biodegradable polymeric porous structures with properties selected to promote tissue regeneration and while providing appropriate mechanical support during tissue regeneration. 2. Cellular populations that can influence and enhance regeneration. 3. The use of growth and morphogenetic factors which can influence cellular migration, differentiation and tissue regeneration in vivo. Biodegradable polymers constitute an attractive class of biomaterials for the development of scaffolds due to their flexibility in chemistry and their ability to produce biocompatible degradation products. This paper presents an overview of polymeric scaffold-based bone tissue regeneration and reviews approaches as well as the particular roles of biodegradable polymers currently in use.

Preparation of Renewable Epoxy-Amine Resins With Tunable Thermo-Mechanical Properties, Wettability and Degradation Abilities From Lignocellulose- and Plant Oils-Derived Components

One-hundred percent renewable triphenol—GTF—(glycerol trihydroferulate) and novel bisphenols—GDF_x–(glycerol dihydroferulate) were prepared from lignocellulose-derived ferulic acid and vegetal oil components (fatty acids and glycerol) using highly selective lipase-catalyzed transesterifications. Estrogenic activity tests revealed no endocrine disruption for GDF_x bisphenols. Triethyl-benzyl-ammonium chloride (TEBAC) mediated glycidylation of all bis/triphenols, afforded innocuous bio-based epoxy precursors GDF_xEPO and GTF-EPO. GDF_xEPO were then cured with conventional and renewable diamines, and some of them in presence of GTF-EPO. Thermo-mechanical analyses (TGA, DSC, and DMA) and degradation studies in acidic aqueous solutions of the resulting epoxy-amine resins showed excellent thermal stabilities (T_d5% = 282–310°C), glass transition temperatures (T_g) ranging from 3 to 62°C, tunable tan α, and tunable degradability, respectively. It has been shown that the thermo-mechanical properties, wettability, and degradability of these epoxy-amine resins, can be finely tailored by judiciously selecting the diamine nature, the GTF-EPO content, and the fatty acid chain length.

Versatile cross-linked fatty acid-based polycarbonate networks obtained by thiol–ene coupling reaction

Bio-sourced polycarbonate networks have been synthesized from an alkene-functional fatty-acid based polycarbonate precursor. Cross-linked networks were created using the radical thiol–ene coupling reaction. The resulting polycarbonate materials exhibited versatile properties either influenced by the structure of the cross-linker or the cross-linker/olefin unit ratio. Indeed, the storage modulus above the glass transition temperature could be modulated from 0.9 to 8.9 MPa only by changing the type of cross-linker, i.e. 1,9-nonanedithiol vs. 1,4-benzenedimethanethiol. The cross-linker/olefin unit ratio was also shown to largely impact the polycarbonate networks properties. An elongation at break of nearly 200% was reached when a low cross-linker/olefin ratio was applied. Moreover, functional polycarbonate networks bearing pendant thiol groups were obtained when an excess of dithiol was used with respect to olefin groups.

Bio-sourced polycarbonate networks have been synthesized from an alkene-functional fatty-acid based polycarbonate precursor.

Development of bio-acrylic polymers from Cyrene™: transforming a green solvent to a green polymer

A bio-based methacrylic polymer derived from a green solvent, Cyrene™ through a green synthesis pathway with very high glass transition temperature, thermal stability and high reactivity.

Thickening Supercritical CO₂ with π-Stacked Co-Polymers: Molecular Insights into the Role of Intermolecular Interaction

Vinyl Benzoate/Heptadecafluorodecyl acrylate (VBe/HFDA) co-polymers were synthesized and characterized as thickening agents for supercritical carbon dioxide (SC-CO₂). The solubility and thickening capability of the co-polymer samples in SC-CO₂ were evaluated by measuring cloud point pressure and relative viscosity. The molecular dynamics (MD) simulation for all atoms was employed to simulate the microscopic molecular behavior and the intermolecular interaction of co-polymer⁻CO₂ systems. We found that the introduction of VBe group decreased the polymer⁻CO₂ interaction and increased the polymer⁻polymer interaction, leading to a reduction in solubility of the co-polymers in SC-CO₂. However, the co-polymer could generate more effective inter-chain interaction and generate more viscosity enhancement compared to the Poly(Heptadecafluorodecyl) (PHFDA) homopolymer due to the driving force provided by π-π stacking of the VBe groups. The optimum molar ratio value for VBe in co-polymers for the viscosity enhancement of SC-CO₂ was found to be 0.33 in this work. The P(HFDA_0.67-co-VBe_0.33) was able to enhance the viscosity of SC-CO₂ by 438 times at 5 wt. %. Less VBe content would result in a lack of intermolecular interaction, although excessive VBe content would generate more intramolecular π-π stacking and less intermolecular π-π stacking. Both conditions reduce the thickening capability of the P(HFDA-co-VBe) co-polymer. This work presented the relationship between structure and performance of the co-polymers in SC-CO₂ by combining experiment and molecular simulations.