Bio-synthesized TiO2 nanoparticles and the aqueous binder-based anode derived thereof for lithium-ion cells

Titanium dioxide nanoparticles (TiO2-NPs) are a promising anode material for Lithium-ion batteries (LIBs) due to their good rate capability, low cost, non-toxicity, excellent structural stability, extended cycle life, and low volumetric change (∼4%) during the Li+ insertion/de-insertion process. In the present paper, anatase TiO2-NPs with an average particle size of ~ 12 nm were synthesized via a green synthesis route using Beta vulgaris (Beetroot) extract, and the synthesized TiO2-NPs were evaluated as anode material in LIBs. Furthermore, we employed an aqueous binder (1:1 mixture of carboxy methyl cellulose and styrene butadiene) for electrode processing, making the process cost-effective and environmentally friendly. The results revealed that the Li/TiO2 half-cells delivered an initial discharge capacity of 209.7 mAh g-1 and exhibited superior rate capability (149 mAh g-1 at 20 C) and cycling performances. Even at the 5C rate, the material retained a capacity of 82.2% at the end of 100 cycles. The synthesis route of TiO2-NPs and the aqueous binder-based electrode processing described in the present work are facile, green, and low-cost and are thus practically beneficial for producing low-cost and high-performance anodes for advanced LIBs.

Phosphorus-doped TiO2mesoporous nanocrystals for anodes in high-current-rate lithium ion batteries

Limited by the intrinsic low electronic conductivity and inferior electrode kinetics, the use of TiO2as an anode material for lithium ion batteries (LIBs) is hampered. Nanoscale surface-engineering strategies of morphology control and particle size reduction have been devoted to increase the lithium storage performances. It is found that the ultrafine nanocrystal with mesoporous framework plays a crucial role in achieving the excellent electrochemical performances due to the surface area effect. Herein, a promising anode material for LIBs consisting of phosphorus-doped TiO2mesoporous nanocrystals (P-TMC) with ultrafine size of 2-8 nm and high specific surface area (234.164 m2g-1) has been synthesized. It is formed through a hydrothermal process and NaBH4assisted heat treatment for anatase defective TiO2(TiO2-x) formation followed by a simple gas phosphorylation process in a low-cost reactor for P-doping. Due to the merits of the large specific surface area for providing more reaction sites for Li+ions to increase the storage capacity and the presence of oxygen vacancies and P-doping for enhancing material's electronic conductivity and diffusion coefficient of ions, the as-designed P-TMC can display improved electrochemical properties. As a LIB anode, it can deliver a high reversible discharge capacity of 187 mAh g-1at 0.2 C and a good long cycling performance with ∼82.6% capacity retention (101 mAh g-1) after 2500 cycles at 10 C with an average capacity loss of only 0.007% per cycle. Impressively, even the current rate increases to 100 times of the original rate, a satisfactory capacity of 104 mAh g-1can be delivered, displaying good rate capacity. These results suggest the P-TMC a viable choice for application as an anode material in LIB applications. Also, the strategy in this work can be easily extended to the design of other high-performance electrode materials with P-doping for energy storage.

Electronic Bulk and Surface Properties of Titanium Dioxide Studied by DFT-1/2

Transparent conductive oxides, such as TiO2, are important functional materials for optoelectronic and photovoltaic devices. We investigate the electronic bulk properties of the TiO2 phases rutile and anatase with the DFT-1/2 method and obtain a quantitatively good description of their electronic band structures. We then applied this method to the (001) surfaces of rutile and anatase and calculated their ionization potentials (IPs) and work functions (WF). To relate these calculated surface properties with values from experiments, we evaluated the effect of varying the oxygen stoichiometry at the surface on both IP and WF.

A novel electrochemical aptasensor based on eco-friendly synthesized titanium dioxide nanosheets and polyethyleneimine grafted reduced graphene oxide for ultrasensitive and selective detection of ciprofloxacin

Developing a rapid, sensitive, and efficient analytical method for the trace-level determination of highly concerning antibiotic ciprofloxacin (CIP) is desirable to guarantee the safety of human health and ecosystems. In this work, a novel electrochemical aptasensor based on polyethyleneimine grafted reduced graphene oxide and titanium dioxide (rGO/PEI/TiO2) nanocomposite was constructed for ultrasensitive and selective detection of CIP. Through the in-situ electrochemical oxidation of Ti3C2Tx nanosheets, TiO2 nanosheets with good electrochemical response were prepared in a more convenient and eco-friendly method. The prepared TiO2 nanosheets promote charge transferring on electrode interface, and [Fe(CN)6]3-/4- as electrochemical active substance can be electrostatically attracted by rGO/PEI. Thus, electrochemical detection signal of the aptasensor variates a lot after specific binding with CIP, achieving working dynamic range of 0.003-10.0 μmol L-1, low detection limit down to 0.7 nmol L-1 (S/N = 3) and selectivity towards other antibiotics. Additionally, the aptasensor exhibited good agreement with HPLC method at 95% confidence level, and achieved good recoveries (96.8-106.3%) in real water samples, demonstrating its suitable applicability of trace detection of CIP in aquatic environment.

TiO2-Coated Silicon Nanoparticle Core-Shell Structure for High-Capacity Lithium-Ion Battery Anode Materials

Silicon-based anode materials are considered one of the highly promising anode materials due to their high theoretical energy density; however, problems such as volume effects and solid electrolyte interface film (SEI) instability limit the practical applications. Herein, silicon nanoparticles (SiNPs) are used as the nucleus and anatase titanium dioxide (TiO₂) is used as the buffer layer to form a core-shell structure to adapt to the volume change of the silicon-based material and improve the overall interfacial stability of the electrode. In addition, silver nanowires (AgNWs) doping makes it possible to form a conductive network structure to improve the conductivity of the material. We used the core-shell structure SiNPs@TiO₂/AgNWs composite as an anode material for high-efficiency Li-ion batteries. Compared with the pure SiNPs electrode, the SiNPs@TiO₂/AgNWs electrode exhibits excellent electrochemical performance with a first discharge specific capacity of 3524.2 mAh·g^-1 at a current density of 400 mA·g^-1, which provides a new idea for the preparation of silicon-based anode materials for high-performance lithium-ion batteries.

Ordering Transitions of Liquid Crystals Triggered by Metal Oxide-catalyzed Reactions of Sulfur Oxide Species

Liquid crystals (LCs), when supported on reactive surfaces, undergo changes in ordering that can propagate over distances of micrometers, thus providing a general and facile mechanism to amplify atomic-scale transformations on surfaces into the optical scale. While reactions on organic and metal substrates have been coupled to LC-ordering transitions, metal oxide substrates, which offer unique catalytic activities for reactions involving atmospherically important chemical species such as oxidized sulfur species, have not been explored. Here, we investigate this opportunity by designing LCs that contain 4'-cyanobiphenyl-4-carboxylic acid (CBCA) and respond to surface reactions triggered by parts-per-billion concentrations of SO₂ gas on anatase (101) substrates. We used electronic structure calculations to predict that the carboxylic acid group of CBCA binds strongly to anatase (101) in a perpendicular orientation, a prediction that we validated in experiments in which CBCA (0.005 mol %) was doped into an LC (4'-n-pentyl-4-biphenylcarbonitrile). Both experiment and computational modeling further demonstrated that SO₃-like species, produced by a surface-catalyzed reaction of SO₂ with H₂O on anatase (101), displace CBCA from the anatase surface, resulting in an orientational transition of the LC. Experiments also reveal the LC response to be highly selective to SO₂ over other atmospheric chemical species (including H₂O, NH₃, H₂S, and NO₂), in agreement with our computational predictions for anatase (101) surfaces. Overall, we establish that the catalytic activities of metal oxide surfaces offer the basis of a new class of substrates that trigger LCs to undergo ordering transitions in response to chemical species of relevance to atmospheric chemistry.

Preparation and Photocatalytic Properties of Anatase TiO2 with Hollow Hexagonal Frame Structure

Titanium dioxide (TiO2) has been widely used to solve energy and environmental pollution problems due to its excellent properties. In this study, the precursor (HTiOF3) with a spherical structure composed of hexagonal prisms was prepared via a simple solvothermal method using tetrabutyl titanate, hydrofluoric acid, glacial acetic acid and isopropanol as raw materials. Then, the calcination time and temperature of the precursor were controlled to prepare anatase TiO2 with different morphologies, and the photocatalytic performance of the prepared catalysts was studied. When the precursor was calcined at 600 °C for 7 h, the prepared TiO2 had a unique hexagonal framework structure and exhibited excellent photocatalytic performance. The degradation rate of the RhB solution was 98.58% at 40 min and the rate of hydrogen evolution was 2508.12 μmol g−1 h−1.

Preparation of Hybrid Sol-Gel Materials Based on Living Cells of Microorganisms and Their Application in Nanotechnology

Microorganism-cell-based biohybrid materials have attracted considerable attention over the last several decades. They are applied in a broad spectrum of areas, such as nanotechnologies, environmental biotechnology, biomedicine, synthetic chemistry, and bioelectronics. Sol-gel technology allows us to obtain a wide range of high-purity materials from nanopowders to thin-film coatings with high efficiency and low cost, which makes it one of the preferred techniques for creating organic-inorganic matrices for biocomponent immobilization. This review focuses on the synthesis and application of hybrid sol-gel materials obtained by encapsulation of microorganism cells in an inorganic matrix based on silicon, aluminum, and transition metals. The type of immobilized cells, precursors used, types of nanomaterials obtained, and their practical applications were analyzed in detail. In addition, techniques for increasing the microorganism effective time of functioning and the possibility of using sol-gel hybrid materials in catalysis are discussed.

Exploring the Effect of Cation Vacancies in TiO2: Lithiation Behavior of n-Type and p-Type TiO2

TiO₂ offers several advantages over graphite as an anode material for Li-ion batteries (LIBs) but suffers from low electrical conductivity and Li-diffusion issues. Control over defect chemistry has proven to be an effective strategy to overcome these issues. However, defect engineering has primarily been focused on oxygen vacancies (V_O). The role of another intrinsic TiO₂ vacancy [i.e., titanium vacancies (V_Ti)] with regard to the Li⁺ storage behavior of TiO₂ has largely evaded attention. Hence, a comparison of V_O- and V_Ti-defective TiO₂ can provide valuable insight into how these two types of defects affect Li⁺ storage behavior. To eliminate other factors that may also affect the Li⁺ storage behavior of TiO₂, we carefully devised synthesis protocols to prepare TiO₂ with either V_O (n-TiO₂) or V_Ti (p-TiO₂). Both TiO₂ materials were verified to have a very similar morphology, surface area, and crystal structure. Although V_O provided additional sites that improved the capacity at low C-rates, the benefit obtained from over-lithiation turned out to be detrimental to cycling stability. Unlike V_O, V_Ti could not serve as an additional lithium reservoir but could significantly improve the rate performance of TiO₂. More importantly, the presence of V_Ti prevented over-lithiation, significantly improving the cycling stability of TiO₂. We believe that these new insights could help guide the development of high-performance TiO₂ for LIB applications.

Development of an efficient CVD technique to prepare TiO2/porous-carbon nanocomposites for high rate lithium-ion capacitors

Titanium dioxide is a promising electrode material for lithium-ion capacitors. When using TiO₂ as an electrode material, it is necessary to combine it with carbon at the nanometer level to improve its low electrical conductivity and low reactivity with Li⁺. However, preparation methods of reported TiO₂/porous–carbon nanocomposites are generally not cost-effective, and their productivities are low. In this study, the vacuum liquid-pulse chemical vapor deposition (VLP-CVD) technique was developed to easily prepare TiO₂/porous–carbon nanocomposites, where TiO₂ nanoparticles with a diameter of ∼4 nm could be homogeneously deposited inside the pores of meso- or macroporous carbons. Because the deposited TiO₂ nanoparticles had access to effective electrically conductive paths formed by the porous–carbon substrate, they showed a high discharge capacity of ∼200 mA h g⁻¹-TiO₂ (based on TiO₂ weight). In particular, the composite prepared from macroporous carbon showed an extremely high rate performance, where 50% of the discharge capacity was retained at a current density of 15 000 mA g⁻¹ when compared to that measured at 50 mA g⁻¹. In addition, the composite also showed very high cyclability, where 80% of the discharge capacity was retained at the 10 000^th cycle. Because the VLP-CVD technique can be performed using simple apparatus and commercially available starting materials, it can be expected to boost industrial production of TiO₂/porous–carbon for lithium-ion capacitors.

TiO₂ nanoparticles with a diameter of around 5 nm were homogeneously deposited inside the pores of meso-macroporous carbons.

Fully Reversible Electrically Induced Photochromic-Like Behaviour of Ag:TiO2 Thin Films

A TiO2 thin film, prepared on fluorine-doped indium tin oxide (FTO)-coated glass substrate, from commercial off-the-shelf terpinol-based paste, was used to directly adsorb Ag plasmonic nanoparticles capped with polyvinylpyrollidone (PVP) coating. The TiO2 film was sintered before the surface entrapment of Ag nanoparticles. The composite was evaluated in terms of spectroelectrochemical measurements, cyclic voltammetry as well as structural methods such as scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD). It was found that the Ag nanoparticles are effectively adsorbed on the TiO2 film, while application of controlled voltages leads to a fully reversible shift of the plasmon peak from 413 nm at oxidation inducing voltages to 440 nm at reducing voltages. This phenomenon allows for the fabrication of a simple photonic switch at either or both wavelengths. The phenomenon of the plasmon shift is due to a combination of plasmon shift related to the form and dielectric environment of the nanoparticles.

Synthesis of nano-sized urchin-shaped LiFePO4 for lithium ion batteries

In this article, the facile synthesis of sea urchin-shaped LiFePO4 nanoparticles by thermal decomposition of metal-surfactant complexes and application of these nanoparticles as a cathode in lithium ion secondary batteries is demonstrated. The advantages of this work are a facile method to synthesize interesting LiFePO4 nanostructures and its synthetic mechanism. Accordingly, the morphology of LiFePO4 particles could be regulated by the injection of oleylamine, with other surfactants and phosphoric acid. This injection step was critical to tailor the morphology of LiFePO4 particles, converting them from nanosphere shapes to diverse types of urchin-shaped nanoparticles. Electron microscopy analysis showed that the overall dimension of the urchin-shaped LiFePO4 particles varied from 300 nm to 2 μm. A closer observation revealed that numerous thin nanorods ranging from 5 to 20 nm in diameter were attached to the nanoparticles. The hierarchical nanostructure of these urchin-shaped LiFePO4 particles mitigated the low tap density problem. In addition, the nanorods less than 20 nm attached to the edge of urchin-shaped nanoparticles significantly increased the pathways for electronic transport.

Biosynthesis of Ag2S/TiO2 nanotubes nanocomposites by Shewanella oneidensis MR-1 for the catalytic degradation of 4-nitrophenol

Biosynthesized nanocomposites are attracting growing interests because they are environmentally friendly. Ag₂S nanoparticles (Ag₂S NPs) are deposited in situ on the surfaces of TiO₂ nanotubes (TNTs) via Shewanella oneidensis MR-1 to form Ag₂S/TNT nanocomposites. The prepared Ag₂S/TNTs nanocomposites are characterized using high-resolution transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and energy-dispersive X-ray spectroscopy. The results show that Ag₂S NPs smaller than 8 nm are successfully synthesized and fabricated on the TNT surfaces with relatively uniform distribution. The catalytic performance of the Ag₂S/TNT nanocomposites is evaluated for catalytic reduction in the presence of NaBH₄ and the photocatalytic degradation of 4-nitrophenol (4-NP) under visible light. The Ag₂S/TNT nanocomposites show excellent catalytic activity and good stability in the 4-NP reduction process. The 4-NP degradation ratio reaches 98.3% in 50 min, and 87% conversion was achieved after eight cycles. The Ag₂S/TNT nanocomposites also exhibit excellent photocatalytic activity for 4-NP at a rate of 0.69 h^-1, and the complete degradation of 4-NP was observed within 5 h. Therefore, this study offers an environmentally friendly approach to synthesize nanocomposites for practical applications.

Electrochemical and Photoelectrochemical Properties of Nickel Oxide (NiO) With Nanostructured Morphology for Photoconversion Applications

The cost-effective production of chemicals in electrolytic cells and the conversion of the radiation energy into electrical energy in photoelectrochemical cells (PECs) require the use of electrodes with large surface area, which possess either electrocatalytic or photoelectrocatalytic properties. In this context nanostructured semiconductors are electrodic materials of great relevance because of the possibility of varying their photoelectrocatalytic properties in a controlled fashion via doping, dye-sensitization or modification of the conditions of deposition. Among semiconductors for electrolysers and PECs the class of the transition metal oxides (TMOs) with a particular focus on NiO interests for the chemical-physical inertness in ambient conditions and the intrinsic electroactivity in the solid state. The latter aspect implies the existence of capacitive properties in TMO and NiO electrodes which thus act as charge storage systems. After a comparative analysis of the (photo)electrochemical properties of nanostructured TMO electrodes in the configuration of thin film the use of NiO and analogs for the specific applications of water photoelectrolysis and, secondly, photoelectrochemical conversion of carbon dioxide will be discussed.

A Study of Controllable Synthesis and Formation Mechanism on Flower-Like TiO2 with Spherical Structure

The development of photocatalytic materials with specific morphologies promises to be a good opportunity to discover geometrically relevant properties. Herein, this paper reported a facile hydrothermal method to directly synthesize TiO2 crystals with flower-like structures using tetrabutyl titanate (TBT) as a titanium source and ethylene glycol as an additive. We also proposed a reasonable growth mechanism by controlling reaction time in detail. The as-prepared samples were analyzed by using X-ray diffraction, scanning electron microscopy and transmission electron microscopy for structure and morphology characterization. The N2 adsorption-desorption isotherm results showed that the surface area of flower-like TiO2 with 10 h reaction time can reach 297 m2/g. We evaluated the photocatalytic performance of samples by using the degradation rate of methylene blue (MB) solution under UV-vis light. The TiO2 with 10 h reaction time exhibited a superior photocatalytic property than other samples in degrading MB under UV-vis light irradiation. More importantly, the catalyst could be reused many times. These results could benefit from the special morphology, high crystallinity and large specific surface area of the samples.

Tuning Texture and Morphology of Mesoporous TiO₂ by Non-Hydrolytic Sol-Gel Syntheses

The development of powerful synthetic methodologies is paramount in the design of advanced nanostructured materials. Owing to its remarkable properties and low cost, nanostructured TiO₂ is widely investigated for applications such as photocatalysis, energy conversion or energy storage. In this article we report the synthesis of mesoporous TiO₂ by three different non-hydrolytic sol-gel routes, and we investigate the influence of the synthetic route and of the presence and nature of the solvent on the structure, texture and morphology of the materials. The first route is the well-known ether route, based on the reaction of TiCl₄ with ⁱPr₂O. The second and third routes, which have not been previously described for the synthesis of mesoporous TiO₂, involve the reaction of Ti(OⁱPr)₄ with stoichiometric amounts of acetophenone and benzoic anhydride, respectively. All materials are characterized by XRD, N₂ physisorption and SEM. By playing with the non-hydrolytic route used and the reaction conditions (presence of a solvent, nature of the solvent, calcination), it is possible to tune the morphology and texture of the TiO₂. Depending on the reaction conditions, a large variety of mesoporous TiO₂ nanostructures could be obtained, resulting from the spontaneous aggregation of TiO₂ nanoparticles, either rounded nanoparticles, platelets or nanorods. These nanoparticle networks exhibited a specific surface area up to 250 m² g⁻¹ before calcination, or up to 110 m² g⁻¹ after calcination.

A scanning probe microscopy study of nanostructured TiO2/poly(3-hexylthiophene) hybrid heterojunctions for photovoltaic applications

The nanoscale morphology of photoactive hybrid heterojunctions plays a key role in the performances of hybrid solar cells. In this work, the heterojunctions consist of a nanocolumnar TiO₂ surface covalently grafted with a monolayer of poly(3-hexylthiophene) (P3HT) functionalized with carboxylic groups (-COOH). Through a joint analysis of the photovoltaic properties at the nanoscale by photoconductive-AFM (PC-AFM) and surface photovoltage imaging, we investigated the physical mechanisms taking place locally during the photovoltaic process and the correlation to the nanoscale morphology. A down-shift of the vacuum level of the TiO₂ surface upon grafting was measured by Kelvin probe force microscopy (KPFM), evidencing the formation of a dipole at the TiO₂/P3HT-COOH interface. Upon in situ illumination, a positive photovoltage was observed as a result of the accumulation of photogenerated holes in the P3HT layer. A positive photocurrent was recorded in PC-AFM measurements, whose spatial mapping was interpreted consistently with the corresponding KPFM analysis, offering a correlated analysis of interest from both a theoretical and material design perspective.

Surface Characteristic Effect of Ag/TiO2 Nanoarray Composite Structure on Supercapacitor Electrode Properties

Ag-ion-modified titanium nanotube (Ag/TiO2-NT) arrays were designed and fabricated as the electrode material of supercapacitors for electrochemical energy storage. TiO2 nanotube (NT) arrays were prepared by electrochemical anodic oxidation and then treated by Ag metal vapor vacuum arc (MEVVA) implantation. The Ag amount was controlled via adjusting ion implantation parameters. The morphology, crystallinity, and electrochemistry properties of as-obtained Ag/TiO2-NT electrodes were distinguished based on various characterizations. Compared with different doses of Ag/TiO2-NTs, the electrode with the dose of 5.0 × 1017 ions·cm-2 exhibited much higher electrode capacity and greatly enhanced activity in comparison to the pure TiO2-NTs. The modified electrode showed a high capacitance of 9324.6 mF·cm-3 (86.9 mF·g, 1.2 mF·cm-2), energy density of 82.8 μWh·cm-3 (0.8 μWh·g, 0.0103 μWh·cm-2), and power density of 161.0 mW·cm-3 (150.4 μW·g, 2.00 μW·cm-2) at the current density of 0.05 mA. Therefore, Ag/TiO2-NTs could act as a feasible electrode material of supercapacitors.

Ustinov A, Sergienko VI. Effect of Hf-doping on electrochemical performance of anatase TiO2 as an anode material for lithium storage

Hafnium-doped titania (Hf/Ti = 0.01; 0.03; 0.05) had been facilely synthesized via a template sol-gel method on carbon fibre. Physico-chemical properties of the as-synthesized materials were characterized by X-ray diffraction, Raman spectroscopy, scanning electron microscopy, energy-dispersive X-ray analysis, scanning transmission electron microscopy, X-ray photoelectron spectroscopy, thermogravimetry analysis and Brunauer-Emmett-Teller measurements. It was confirmed that Hf4+ substitute in the Ti4+ sites, forming Ti1-x Hf x O2 (x = 0.01; 0.03; 0.05) solid solutions with an anatase crystal structure. The Ti1-x Hf x O2 materials are hollow microtubes (length of 10-100 µm, outer diameter of 1-5 µm) composed of nanoparticles (average size of 15-20 nm) with a surface area of 80-90 m2 g-1 and pore volume of 0.294-0.372 cm3 g-1. The effect of Hf ion incorporation on the electrochemical behaviour of anatase TiO2 in the Li-ion battery anode was investigated by galvanostatic charge/discharge and electrochemical impedance spectroscopy. It was established that Ti0.95Hf0.05O2 shows significantly higher reversibility (154.2 mAh g-1) after 35-fold cycling at a C/10 rate in comparison with undoped titania (55.9 mAh g-1). The better performance offered by Hf4+ substitution of the Ti4+ into anatase TiO2 mainly results from a more open crystal structure, which has been achieved via the difference in ionic radius values of Ti4+ (0.604 Å) and Hf4+ (0.71 Å). The obtained results are in good accord with those for anatase TiO2 doped with Zr4+ (0.72 Å), published earlier. Furthermore, improved electrical conductivity of Hf-doped anatase TiO2 materials owing to charge redistribution in the lattice and enhanced interfacial lithium storage owing to increased surface area directly depending on the Hf/Ti atomic ratio have a beneficial effect on electrochemical properties.

Tuning the Electronic Conductivity in Hydrothermally Grown Rutile TiO₂ Nanowires: Effect of Heat Treatment in Different Environments

Hydrothermally grown rutile TiO₂ nanowires are intrinsically full of lattice defects, especially oxygen vacancies. These vacancies have a significant influence on the structural and electronic properties of the nanowires. In this study, we report a post-growth heat treatment in different environments that allows control of the distribution of these defects inside the nanowire, and thus gives direct access to tuning of the properties of rutile TiO₂ nanowires. A detailed transmission electron microscopy study is used to analyze the structural changes inside the nanowires which are correlated to the measured optical and electrical properties. The highly defective as-grown nanowire arrays have a white appearance and show typical semiconducting properties with n-type conductivity, which is related to the high density of oxygen vacancies. Heat treatment in air atmosphere leads to a vacancy condensation and results in nanowires which possess insulating properties, whereas heat treatment in N₂ atmosphere leads to nanowire arrays that appear black and show almost metal-like conductivity. We link this high conductivity to a TiO_2-x shell which forms during the annealing process due to the slightly reducing N₂ environment.

Controlled release and biocompatibility of polymer/titania nanotube array system on titanium implants

Bacterial infection and tissue inflammation are the major causes of early failure of titanium-based orthopedic implants; thus, surgical implants with tunable drug releasing properties represent an appealing way to address some of these problems of bacterial infection and tissue inflammation in early age of orthopedic implants. In this work, a hybrid surface system composed of biodegradable poly(lactic-co-glycolic acid) (PLGA) and titania nanotubes (TNTs) has been successfully constructed on Ti implants with the aim of preventing bacterial infection via long-term drug release. By varying the size of the TNTs and the thickness of the polymer film, the drug release profile can be tuned to achieve the optimal therapeutic action throughout the treatment time. The size of TNTs plays a dominant role in the drug loading dose of TNTs/PLGA hybrid coatings. In this work, TNTs with an average size of 80 nm can achieve the largest loading dose. Depending on the polymer thickness, significant improvement in the drug release characteristics is attained, for instance, reduced burst release (from 84% to 27%) and overall release time extended from 5 to over 40 days. In addition, the PLGA layers may favor the proliferation and osteogenesis of MC3T3-E1 mouse cells at an earlier stage. Therefore, this TNT/PLGA hybrid surface system can be employed as an effective bioplatform for improving both self-antibacterial performance and biocompatibility of Ti-based biomaterials.

•

The TNT/PLGA coatings system is successfully constructed on titanium implants.

•

TNTs with an average size of 80 nm can achieve the largest loading dose of ibuprofen.

•

This system shows reduced burst release (from 84% to 27%).

•

This system can achieve long-term release of drugs over 40 days.

•

The surface system exhibits good biocompatibility.

Preparation of porous TiO2 photocatalyts with different crystal phases and high catalytic activity by simple calcination of titanate nanofibers

Porous TiO₂ materials with different crystal phases and large surface area were prepared by calcining titanate nanofibers under different temperatures for efficient photocatalysis.

Synthesis, Characterization, and Photocatalytic Properties of Sulfur- and Carbon-Codoped TiO2 Nanoparticles

One-step TiO2 nanoparticle synthesis based on the interaction between thiourea and metatitanic acid is applied for sulfur and carbon anatase codoping. The synthesis of the doped TiO2 has been monitored by means of differential thermal analysis and thermogravimetric analysis (DTA-TG), which allows determining the optimal thermal conditions for the process. Electron microscopy showed micrometer-sized (5-15 μm) randomly distributed crystal aggregates, consisting of many 15-40-nm TiO2 nanoparticles. The obtained phase composition and chemical states of the doping elements are analyzed by means of X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), infrared (IR) and Raman spectroscopies, and electron paramagnetic resonance (EPR). XRD displays in both samples (doped and pristine) the existence of only one crystalline phase-the tetragonal modification of TiO2-anatase. Further data assessment by means of Rietveld refinement allowed detection of a slight c lattice parameter and volume increase related to incorporation of the doping elements. XPS demonstrated the presence of carbon and sulfur as doping elements in the material. It was confirmed that carbon is in elemental form and also present in oxygen-containing compounds, which are adsorbed on the particle surface. The binding energy for sulfur electron core shell corresponds to the established data for sulfate compounds, where sulfur is in 6+ oxidation state. The synthesized S- and C-codoped TiO2 showed excellent photocatalytic performance during the degradation of organic dyes (rhodamine B, methylene blue), gas-phase oxidation of ethanol under visible light, and photocatalytic hydrogen generation from ethanol under ultraviolet light.

Enhancing Performance of CdS Quantum Dot-Sensitized Solar Cells by Two-Dimensional g-C3N4 Modified TiO2 Nanorods

In present work, two-dimensional g-C₃N₄ was used to modify TiO₂ nanorod array photoanodes for CdS quantum dot-sensitized solar cells (QDSSCs), and the improved cell performances were reported. Single crystal TiO₂ nanorods are prepared by hydrothermal method on transparent conductive glass and spin-coated with g-C₃N₄. CdS quantum dots were deposited on the g-C₃N₄ modified TiO₂ photoanodes via successive ionic layer adsorption and reaction method. Compared with pure TiO₂ nanorod array photoanodes, the g-C₃N₄ modified photoanodes showed an obvious improvement in cell performances, and a champion efficiency of 2.31 % with open circuit voltage of 0.66 V, short circuit current density of 7.13 mA/cm², and fill factor (FF) of 0.49 was achieved, giving 23 % enhancement in cell efficiency. The improved performances were due to the matching conduction bands and valence bands of g-C₃N₄ and TiO₂, which greatly enhanced the separation and transfer of the photogenerated electrons and holes and effectively suppressed interfacial recombination. Present work provides a new direction for improving performance of QDSSCs.

Oxygen vacancy induced fast lithium storage and efficient organics photodegradation over ultrathin TiO2 nanolayers grafted graphene sheets

In this work we have developed a unique structure of ultrathin (5nm) TiO2 nanolayers grafted graphene nanosheets (TiO2/G) and integrated oxygen vacancy (VO) into TiO2 to enhance its lithium storage and photocatalytic performances. The defective TiO2/G was synthesized by a solvothermal and subsequent thermal treatment method. When treated in a H2 atmosphere, the resulting TiO2-x/G(H2) has lower crystallinity, smaller crystal size, richer surface VO, higher surface area, larger pore volume, and lower charge transfer resistance than that reduced by NaBH4 solid, i.e., TiO2-x/G(NaBH4). More importantly, the surface VO in the TiO2-x/G(H2) could remarkably inhibit the recombination of photogenerated electron-hole pairs compared with the bulk Vo in the TiO2-x/G(NaBH4). As a result, the combination of all the factors contributed to the superiority of TiO2-x/G(H2), which demonstrated not only 70% higher specific capacity, longer cycling performance (1000 cycles) and better rate capability for lithium-ion battery, but also higher photocatalytic activity and 1.5 times faster degradation rate for organic pollutants removal than TiO2-x/G(NaBH4). The findings in this work will benefit the fundamental understanding of TiO2/G surface chemistry and advance the design and preparation of functional materials for energy storage and water treatment.

Fast diffusion of silver in TiO2 nanotube arrays

Using magnetron sputtering and heat treatment, Ag@TiO2 nanotubes are prepared. The effects of heat-treatment temperature and heating time on the evolution of Ag nanofilms on the surface of TiO2 nanotubes and microstructure of Ag nanofilms are investigated by X-ray diffraction, field emission scanning electron microscopy, and transmission electron microscopy. Ag atoms migrate mainly on the outmost surface of the TiO2 nanotubes, and fast diffusion of Ag atoms is observed. The diffusivity for the diffusion of Ag atoms on the outmost surface of the TiO2 nanotubes at 400 °C is 6.87 × 10(-18) m(2)/s, which is three orders of magnitude larger than the diffusivities for the diffusion of Ag through amorphous TiO2 films. The activation energy for the diffusion of Ag atoms on the outmost surface of the TiO2 nanotubes in the temperature range of 300 to 500 °C is 157 kJ/mol, which is less than that for the lattice diffusion of Ag and larger than that for the grain boundary diffusion. The diffusion of Ag atoms leads to the formation of Ag nanocrystals on the outmost surface of TiO2 nanotubes. Probably there are hardly any Ag nanocrystals formed inside the TiO2 nanotubes through the migration of Ag.

Low temperature synthesis of hierarchical TiO2 nanostructures for high performance perovskite solar cells by pulsed laser deposition

High aspect-ratio TiO₂ nanostructures directly assembled with pulsed laser deposition could improve interfacial contact for superior perovskite photovoltaic cells.

Three dimensional hierarchically porous crystalline MnO2 structure design for a high rate performance lithium-ion battery anode

A hierarchically porous crystalline MnO₂ anode was applied to a lithium ion battery and exhibited long cycling life and high rate performance.

Diffusion kinetics of gold in TiO2 nanotube arrays for formation of Au@TiO2 nanotube arrays

Heating treatment leads to the diffusion of Au into TiO₂ nanotube arrays and the formation of Au nanocrystals. The activation energy for the Au diffusion on the surface of the TiO₂ nanotubes in the temperature range of 400 to 500 °C is 67.2 kJ mol⁻¹.

Solution combustion synthesis of metal oxide nanomaterials for energy storage and conversion

The design and synthesis of metal oxide nanomaterials is one of the key steps for achieving highly efficient energy conversion and storage on an industrial scale. Solution combustion synthesis (SCS) is a time- and energy-saving method as compared with other routes, especially for the preparation of complex oxides which can be easily adapted for scale-up applications. This review summarizes the synthesis of various metal oxide nanomaterials and their applications for energy conversion and storage, including lithium-ion batteries, supercapacitors, hydrogen and methane production, fuel cells and solar cells. In particular, some novel concepts such as reverse support combustion, self-combustion of ionic liquids, and creation of oxygen vacancies are presented. SCS has some unique advantages such as its capability for in situ doping of oxides and construction of heterojunctions. The well-developed porosity and large specific surface area caused by gas evolution during the combustion process endow the resulting materials with exceptional properties. The relationship between the structural properties of the metal oxides studied and their performance is discussed. Finally, the conclusions and perspectives are briefly presented.

Template-Free Synthesis of Ruthenium Oxide Nanotubes for High-Performance Electrochemical Capacitors

One-dimensional, hydrous ruthenium oxide nanotubes (RuO2·1.84H2O) have been successfully achieved using a template-free, microwave-hydrothermal process. These were found to be amorphous in nature and have a large specific surface area of 250 m(2)·g(-1), producing a specific and volumetric capacitance of 511 F·g(-1) and 531 F·cm(-3), respectively, at a discharging current density of 0.5 A·g(-1). When used as an electrode material in an electrochemical capacitor or ultracapacitor, they produced a significant improvement in capacitance, rate capability, and cyclability that can be attributed to the hollow nature of tubes allowing greater contact between the active surface of the electrode and the electrolyte.

Direct alcohol fuel cells: toward the power densities of hydrogen-fed proton exchange membrane fuel cells

A 2 μm thick layer of TiO2 nanotube arrays was prepared on the surface of the Ti fibers of a nonwoven web electrode. After it was doped with Pd nanoparticles (1.5 mgPd  cm(-2) ), this anode was employed in a direct alcohol fuel cell. Peak power densities of 210, 170, and 160 mW cm(-2) at 80 °C were produced if the cell was fed with 10 wt % aqueous solutions of ethanol, ethylene glycol, and glycerol, respectively, in 2 M aqueous KOH. The Pd loading of the anode was increased to 6 mg cm(-2) by combining four single electrodes to produce a maximum peak power density with ethanol at 80 °C of 335 mW cm(-2) . Such high power densities result from a combination of the open 3 D structure of the anode electrode and the high electrochemically active surface area of the Pd catalyst, which promote very fast kinetics for alcohol electro-oxidation. The peak power and current densities obtained with ethanol at 80 °C approach the output of H2 -fed proton exchange membrane fuel cells.

The fabrication and the characterization of a TiO2/titanate nanohybrid for efficient hydrogen evolution

A facile one-step hydrothermal route for a TiO₂/titanate nanojunction has been developed for improving the photocatalytic activity of hydrogen evolution.

Toward elevated light harvesting: efficient dye-sensitized solar cells with titanium dioxide/silica photoanodes

Light harvesting titanium dioxide/silica photoanodes are used for dye-sensitized solar cells.

Engineering a high energy surface of anatase TiO2 crystals towards enhanced performance for energy conversion and environmental applications

Great progress has been made in surface engineering of anatase TiO₂ crystals at the atomic level so as to fundamentally understand the surface-dependent properties. Herein, we summarize important achievements in this field, focusing on facets with high surface energy.