Alendronate-Functionalized Graphene Quantum Dots as an Effective Fluorescent Sensing Platform for Arsenic Ion Detection

Alendronate-functionalized graphene quantum dots (ALEN-GQDs) with a quantum yield of 57% were synthesized via a two-step route: preparation of graphene quantum dots (GQDs) by pyrolysis method using citric acid as the carbon source and post functionalization of GQDs via a hydrothermal method with alendronate sodium. After careful characterization of the obtained ALEN-GQDs, they were successfully employed as sensing materials with superior selectivity and sensitivity for the detection of nanomolar levels of arsenic ions (As(III)). According to the mechanistic investigation, arsenic ions can quench the fluorescence intensity of ALEN-GQDs through metal-ligand interaction between the As(III) ions and the surface functional groups of the fluorescent probe. This probe provided a rapid method to monitor As(III) with a wide detection range (44 nM-1.30 µM) and a low detection limit of 13 nM. Finally, to validate the applicability, this novel fluorescent probe was successfully applied for the quantitative determination of As(III) in rice and water samples.

Phenol-Furfural Resin/Graphite/Ag-Based Electrically Conductive Adhesive Composites from Waste Bagasse with Enhanced Thermo-Electric Properties

This study describes the preparation and evaluation of phenol-furfural resin (PFR) from bagasse and its nanocomposites for electrically conductive adhesive (ECA) application. PFR was prepared with furfural extracted from bagasse using a modified acid digestion method. Three different formulations of PFR nanocomposites with conductive nanoparticles, i.e., PFR-silver, PFR-graphite, and PFR-silver + graphite, were prepared using 20, 40, and 60 w/w% of fillers via the impregnation method. The resultant products were characterized using FT-IR, SEM, EDS, and XRD spectroscopy. Electrical conductivity was measured using a four-probe technique, while band gap was calculated via Tauc plots. The results exhibited a significant rise in electrical conductivity of insulating virgin PFR from 2.6 × 10-4 Scm-1 to 8.2 × 10-1 Scm-1 with a 40 and 20 w/w% blend of Ag and graphite in PFR. This synergism was exhibited because graphite and Ag NPs supply excellent junctions for building networks. Both tend to coalesce due to van der Waals forces and high surface energies. Therefore, conductive pathway numbers can be increased, and the contact area can be effectively enlarged. This ternary composite exhibited the lowest bandgap energy value, i.e., 3.1 eV. Thermogravimetric temperature values T0 and Tdeg were increased up to 120 °C and 484 °C, respectively, showing a significant increase in thermal stability. Therefore, the resultant nanocomposite material has good potential to be employed as an ECA in the electronic industry.

Green synthesis of graphene-based metal nanocomposite for electro and photocatalytic activity; recent advancement and future prospective

The presence of pollutants in waste water is a demanding problem for human health. Investigations have been allocated to study the adsorptive behavior of graphene-based materials to remove pollutants from wastewater. Graphene (GO) due to its hydrophilicity, high surface area, and oxygenated functional groups, is an effective adsorbent for the removal of dyes and heavy metals from water. The disclosure of green synthesis opened the gateway for the economic productive methods. This article reveals the fabrication of graphene-based composite from aloe vera extract using a green method. The proposed mechanism of GO reduction via plant extract has also been mentioned in this work. The mechanism associated with the removal of dyes and heavy metals by graphene-based adsorbents and absorptive capacities of heavy metals has been discussed in detail. The toxicity of heavy metals has also been mentioned here. The Polyaromatic resonating system of GO develops significant π-π interactions with dyes whose base form comprises principally oxygenated functional groups. This review article illustrates a literature survey by classifying graphene-based composite with a global market value from 2010 to 2025 and also depicts a comparative study between green and chemical reduction methods. It presents state of art for the fabrication of GO with novel adsorbents such as metal, polymer, metal oxide and elastomers-based nanocomposites for the removal of pollutants. The current progress in the applications of graphene-based composites in antimicrobial, anticancer, drug delivery, and removal of dyes with photocatalytic efficacy of 73% is explored in this work. It gives a coherent overview of the green synthesis of graphene-based composite, various prospective for the fabrication of graphene, and their biotoxicity.

Selective detection of tartaric acid using amino acid interlinked silver nanoparticles as a colorimetric probe

A variety of biomolecules with different functional groups play critical roles in almost all the processes occurring in living cells. Interaction of metallic nanoparticles (NPs) with various biomolecules generates a layer of molecules on their surface, and this biomolecular rich layer formed on the NP surface is described as a "biomolecular corona". The physicochemical properties of the NPs, including size, adsorption affinity, and charge on the particles' surfaces are the major factors influencing the characteristics of this corona. The formation of various biomolecular corona has been studied well, whereas the amino acid corona is relatively new by exploring their stability. In the present study, a novel formation of an amino acid corona with a fundamental interaction mechanism for a selective detection procedure using a colorimetric platform has been proposed. Herein, amino acid-coated silver NPs (AgNPs) have been used as a template with spectroscopic (steady state UV-Vis, FTIR) and imaging (HR-TEM, DLS) techniques. Our findings demonstrated that among different amino acid coronas, glutathione (GSH) stabilized AgNPs show a rapid reaction with tartaric acid. The extent and thermodynamics of the formed complex between the GSH/AgNPs and tartaric acid have also been studied and this suggested that the complex formed is spontaneous and energy releasing in nature.

ZnAl2O4 Nanomaterial as a Naked-Eye Arsenate Sensor: A Combined Experimental and Computational Mechanistic Approach

Raising public awareness over the emerging health risk due to intake of arsenic-contaminated potable water is a matter of great concern. Exploration of cost-effective, self-testing kits is a substantial way to reach out to the masses and detect the presence of arsenate in water. With this agenda, a photoluminescent Mannich base Zn(II) complex (ZnMC = [Zn₂(ML)₂]·(ClO₄)₂·(H₂O); HML = Mannich base ligand) has been synthesized, and its dinuclearity was verified with single-crystal X-ray diffraction structural analysis. Among a range of anions, ZnMC was found to detect arsenate selectively by showing a turn-off emission with a color change from bright green to dark under UV light. The real-life applicability of the ZnMC probe is somewhat restricted to only sensing of arsenate, but not its removal owing to the fact of its homogeneity. Considering the efficacy of ZnMC as well as a need for its easy removal from water, slight modification has been done with chloride ions in the form of ZnMC″ (=[Zn₂(ML)₂(Cl)₂]), and finally, an interface between homogeneous and heterogeneous solid support has been explored with a strategic fabrication of ZnMC″ grafted ZnAl₂O₄, named as ZAZ nanomaterial. This not only imparts successful segregation of arsenate from drinking water but also provides naked-eye detection under ambient light as well as UV light. Thermodynamic parameters associated with the binding of arsenate to ZnMC and ZAZ have been evaluated through isothermal calorimetric (ITC) measurements. Steady-state and time-resolved fluorescence titration study, absorption titration study, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and computational calculations have been performed to get deep insights into the sensing properties. Proper justification of the sensing mechanism is the highlight of this work. ZAZ nanomaterial has been exploited to produce a self-test paper kit for arsenate detection with a limit of 9.86 ppb, which potentially enables applications in environmental monitoring.

Advances in Electrochemical Detection Electrodes for As(III)

Arsenic is extremely abundant in the Earth's crust and is one of the most common environmental pollutants in nature. In the natural water environment and surface soil, arsenic exists mainly in the form of trivalent arsenite (As(III)) and pentavalent arsenate (As(V)) ions, and its toxicity can be a serious threat to human health. In order to manage the increasingly serious arsenic pollution in the living environment and maintain a healthy and beautiful ecosystem for human beings, it is urgent to conduct research on an efficient sensing method suitable for the detection of As(III) ions. Electrochemical sensing has the advantages of simple instrumentation, high sensitivity, good selectivity, portability, and the ability to be analyzed on site. This paper reviews various electrode systems developed in recent years based on nanomaterials such as noble metals, bimetals, other metals and their compounds, carbon nano, and biomolecules, with a focus on electrodes modified with noble metal and metal compound nanomaterials, and evaluates their performance for the detection of arsenic. They have great potential for achieving the rapid detection of arsenic due to their excellent sensitivity and strong interference immunity. In addition, this paper discusses the relatively rare application of silicon and its compounds as well as novel polymers in achieving arsenic detection, which provides new ideas for investigating novel nanomaterial sensing. We hope that this review will further advance the research progress of high-performance arsenic sensors based on novel nanomaterials.

Performance of graphene-zinc oxide nanocomposite coated-glassy carbon electrode in the sensitive determination of para-nitrophenol

Graphene: zinc oxide nanocomposite (GN:ZnO NC) platform was tried for the sensitive determination of para-nitrophenol (p-NP) through the electrochemical method. ZnO nanoparticles (NPs) were synthesized by the modified wet-chemical method where in potassium hydroxide and zinc nitrate were used as precursors and starch as a stabilizing agent. A green and facile approach was applied to synthesize GN:ZnO NC in which glucose was employed as a reductant to reduce graphene-oxide to graphene in the presence of ZnO NPs. The synthesized NC was characterized using scanning and high-resolution transmission electron microscopy, energy dispersive x-ray analysis, X-ray diffraction and Raman spectroscopic techniques to examine the crystal phase, crystallinity, morphology, chemical composition and phase structure. GN:ZnO NC layer deposited over the glassy carbon electrode (GCE) was initially probed for its electrochemical performance using the standard 1 mM K3[Fe(CN)6] model complex. GN:ZnO NC modified GCE was monitored based on p-NP concentration. An enhanced current response was observed in 0.1 M phosphate buffer of pH 6.8 for the determination of p-NP in a linear working range of 0.09 × 10-6 to 21.80 × 10-6 M with a lower detection limit of 8.8 × 10-9 M employing square wave adsorptive stripping voltammetric technique at a deposition-potential and deposition-time of - 1.0 V and 300 s, respectively. This electrochemical sensor displayed very high specificity for p-NP with no observed interference from some other possible interfering substances such as 2, 4-di-NP, ortho-NP, and meta-NP. The developed strategy was useful for sensitive detection of p-NP quantity in canals/rivers and ground H2O samples with good recoveries.

Noble-metal-free Fe3O4/Co3S4 nanosheets with oxygen vacancies as an efficient electrocatalyst for highly sensitive electrochemical detection of As(III)

The electrochemical method for highly sensitive determination of arsenic(III) in real water samples with noble-metal-free nanomaterials is still a difficult but significant task. Here, an electrochemical sensor driven by noble-metal-free layered porous Fe₃O₄/Co₃S₄ nanosheets was successfully employed for As(III) analysis, which was prepared via a facile two-step method involves a hydrothermal treatment and a subsequent sulfurization process. As expected, the electrochemical detection of As(III) in 0.1 M HAc-NaAc (pH 6.0) by square wave anodic stripping voltammetry (SWASV) with a considerable sensitivity of 4.359 μA/μg·L^-1 was obtained, which is better than the commonly used noble metals modified electrodes. Experimental and characterization results elucidate the enhancement of As(III) electrochemical performance could be attributed to its nano-porous structure, the presence of oxygen vacancies and strong synergetic coupling effects between Fe₃O₄ and Co₃S₄ species. Besides, the Fe₃O₄/Co₃S₄ modified screen printed carbon electrode (Fe₃O₄/Co₃S₄-SPCE) shows remarkable stability and repeatability, valuable anti-interference ability and could be used for detection in real water samples. Consequently, the results confirm that as-prepared porous Fe₃O₄/Co₃S₄ nanosheets is identified as a promising modifier to detect As(III) in real sample analysis.

An Electrochemical Sensor Based on Gold and Bismuth Bimetallic Nanoparticles Decorated L-Cysteine Functionalized Graphene Oxide Nanocomposites for Sensitive Detection of Iron Ions in Water Samples

In this work, gold and bismuth bimetallic nanoparticles decorated L-cysteine functionalized graphene oxide nanocomposites (Au-BiNPs/SH-GO) were prepared and applied to selective detection of Fe(III) in lake and seawater samples by modifying onto glassy carbon electrodes. Bimetallic nanoparticles have various excellent properties and better catalytic properties because of the unique synergistic effect between metals. The modified electrode was characterized by scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and Raman spectroscopy. Under optimized conditions, current peak intensity increased linearly with increasing Fe(III) concentration over the range of 0.2-50 μM and a detection limit of 0.07 μM (S/N = 3). The Au-BiNPs/SH-GO/GCE was used for the determination of Fe(III) in lake and seawater samples with recoveries ranged from 90 to 103%. Those satisfactory results revealed the potential application of the Au-BiNPs/SH-GO electrochemical sensor for heavy metals detection in environmental monitoring.

Application of biosynthesized metal nanoparticles in electrochemical sensors

Recently, the development of eco-friendly, cost-effective and reliable methods for synthesis of metal nanoparticles has drawn a considerable attention. The so-called green synthesis, using mild reaction conditions and natural resources as plant extracts and microorganisms, has established as a convenient, sustainable, cheap and environmentally safe approach for synthesis of a wide range of nanomaterials. Over the past decade, biosynthesis is regarded as an important tool for reducing the harmful effects of traditional nanoparticle synthesis methods commonly used in laboratories and industry. This review emphasizes the significance of biosynthesized metal nanoparticles in the field of electrochemical sensing. There is increasing evidence that green synthesis of nanoparticles provides a new direction in designing of cost-effective, highly sensitive and selective electrode-catalysts applicable in food, clinical and environmental analysis. The article is based on 157 references and provided a detailed overview on the main approaches for green synthesis of metal nanoparticles and their applications in designing of electrochemical sensor devices. Important operational characteristics including sensitivity, dynamic range, limit of detection, as well as data on stability and reproducibility of sensors have also been covered.

Improved green biosynthesis of chitosan decorated Ag- and Co3O4-nanoparticles: A relationship between surface morphology, photocatalytic and biomedical applications

AgNPs@Chitosan and Co₃O₄-NPs@Chitosan were fabricated with Salvia hispanica. Results showed MZI values of 5 and 30 mm for Co₃O₄-NPs- and AgNPs@Chitosan against S. aureus, and 15 and 21 mm for Co₃O₄-NPs- and AgNPs@Chitosan against E. coli (24 h, 20 μg/mL), respectively. MTT assays showed up to 80% and 90%, 71% and 75%, and 91% and 94% mammalian cell viability for the green synthesized, chemically synthesized AgNPs and green synthesized AgNPs@Chitosan for HEK-293 and PC12 cells, respectively, and 70% and 71%, 59% and 62%, and 88% and 73% for the related Co₃O₄-NPs (24 h, 20 μg/mL). The photocatalytic activities showed dye degradation after 135 and 105 min for AgNPs@Chitosan and Co₃O₄-NPs@Chitosan, respectively. FESEM results showed differences in particle sizes (32 ± 3.0 nm for the AgNPs and 41 ± 3.0 nm for the Co₃O₄NPs) but AFM results showed lower roughness of the AgNPs@Chitosan (7.639 ± 0.85 nm) compared to Co₃O₄NPs@Chitosan (9.218 ± 0.93 nm), which resulted in potential biomedical applications.

Dynamic Modification of Fermi Energy in Single-Layer Graphene by Photoinduced Electron Transfer from Carbon Dots

Graphene (Gr)—a single layer of two-dimensional sp² carbon atoms—and Carbon Dots (CDs)—a novel class of carbon nanoparticles—are two outstanding nanomaterials, renowned for their peculiar properties: Gr for its excellent charge-transport, and CDs for their impressive emission properties. Such features, coupled with a strong sensitivity to the environment, originate the interest in bringing together these two nanomaterials in order to combine their complementary properties. In this work, the investigation of a solid-phase composite of CDs deposited on Gr is reported. The CD emission efficiency is reduced by the contact of Gr. At the same time, the Raman analysis of Gr demonstrates the increase of Fermi energy when it is in contact with CDs under certain conditions. The interaction between CDs and Gr is modeled in terms of an electron-transfer from photoexcited CDs to Gr, wherein an electron is first transferred from the carbon core to the surface states of CDs, and from there to Gr. There, the accumulated electrons determine a dynamical n-doping effect modulated by photoexcitation. The CD–graphene interaction unveiled herein is a step forward in the understanding of the mutual influence between carbon-based nanomaterials, with potential prospects in light conversion applications.

A new CQDs/f-MWCNTs/GO nanocomposite electrode for arsenic (10−12M) quantification in bore-well water and industrial effluents

Strategic combination ofCQDs/f-MWCNTs/GO/GCE for pico-molar arsenic sensing.

Graphene-derived nanomaterials as recognition elements for electrochemical determination of heavy metal ions: a review

This review (with 155 refs.) summarizes the progress made in the past few years in the field of electrochemical sensors based on graphene-derived materials for the determination of heavy metal ions. Following an introduction of this field and a discussion of the various kinds of modified graphenes including graphene oxide and reduced graphene oxide, the review covers graphene based electrodes modified (or doped) with (a) heteroatoms, (b) metal nanoparticles, (c) metal oxides, (d) small organic molecules, (e) polymers, and (f) ternary nanocomposites. Tables are provided that afford an overview of representative methods and materials for fabricating electrochemical sensors. Furthermore, sensing mechanisms are discussed. A concluding section presents new perspectives, opportunities and current challenges. Graphical Abstract Schematic illustration of electrochemical sensor for heavy metal ion sensing based on heteroatom-doped graphene, metal-modified graphene, metal-oxide-modified graphene, organically modified graphene, polymer-modified graphene, and ternary graphene based nanocomposites.

Advancement of Ag-Graphene Based Nanocomposites: An Overview of Synthesis and Its Applications

Graphene has been employed as an excellent support for metal nanomaterials because of its unique structural and physicochemical properties. Silver nanoparticles (AgNPs) with exceptional properties have received considerable attention in various fields; however, particle aggregation limits its application. Therefore, the combination of AgNPs and graphene based nanocomposites (Ag-graphene based nanocomposites) has been widely explored to improve their properties and applications. Excitingly, enhanced antimicrobial, catalytic, and surface enhanced Raman scattering properties are obtained after their combination. In order to have a comprehensive knowledge of these nanocomposites, this Review highlights the chemical and biological synthesis of Ag-graphene nanocomposites. In particular, their applications as antimicrobial agents, catalysts, and sensors in biomedicine, agricultural protection, and environmental remediation and detection are covered. Meanwhile, the factors that influence the synthesis and applications are also briefly discussed. Furthermore, several important issues on the challenges and new directions are also provided for further development of these nanocomposites.

Thermally stable hybrid polyarylidene(azomethine-ether)s polymers (PAAP): an ultrasensitive arsenic(III) sensor approach

A new category of thermally stable hybrid polyarylidene(azomethine-ether)s and copolyarylidene(azomethine-ether)s (PAAP) based on diarylidenecycloalkanones has been synthesized using solution polycondensation method. For potential cationic sensor development, a thin layer of PAAP onto a flat glassy carbon electrode (GCE, surface area: 0.0316 cm²) was prepared with conducting nafion (5%) coating agent to fabricate a sensitive and selective arsenic (III) [As³⁺] ion in short response time in neutral buffer system. The fabricated cationic sensor was measured the analytical performances such as higher sensitivity, linear dynamic range, detection limit, reproducibility, and long-term stability towards As³⁺ ions. The sensitivity and detection limit were calculated as 2.714 μAμM^-1cm^-2 and 6.8 ± 0.1 nM (SNR of 3; 3N/S) respectively from the calibration curve. This novel approach can be initiated a well-organized route of an efficient development of heavy selective arsenic sensor for hazardous pollutants in biological, environmental, and health care fields. Real sample analysis for various environmental sample was performed with PAAP-modified-GCE.

A highly sensitive FET-type aptasensor using flower-like MoS2 nanospheres for real-time detection of arsenic(iii)

Arsenic (As) contamination in drinking water is problematic due to its threat to human health. Highly stable, sensitive and selective sensors are needed for As(iii), which is the most toxic of the various forms of arsenic. Herein, we describe the fabrication of field-effect transistor (FET)-type aptasensors for As(iii) detection that is based on carboxylic polypyrrole (CPPy)-coated flower-like MoS₂ nanospheres (CFMNSs). Arsenic-binding aptamer-conjugated CFMNSs were integrated into a liquid-ion gated FET system, leading to extraordinary performance with a rapid response (on a time scale of less than 1 s). Field-induced current changes occurred through the interaction between the aptamer and As(iii), resulting in sensitive discrimination of As(iii) at unprecedentedly low concentrations (ca. 1 pM). Moreover, the CFMNS-based aptasensor selectively recognized As(iii) among numerous other metal ions and accurately detected As(iii) in a mixed solution. The FET aptasensor could also discriminate target analytes in a real sample derived from river water. This MoS₂-based aptasensor is a promising tool for the detection of As(iii) and could be used in a wide range of practical applications.

Preparation, characterization and antibiotic properties of silver–silicon nanocomposites

Ag nanoparticles supported on porous silicon showing excellent antibiotic properties against both E. coli and S. aureus were presented.

A long-range emissive mega-Stokes inorganic–organic hybrid material with peripheral carboxyl functionality for As(v) recognition and its application in bioimaging

We demonstrate a strategy for the recognition of As⁵⁺ in aqueous solution using a red-emissive probe based on a perylene–Cu²⁺ ensemble decorated with peripheral free carboxyl functionality.

Facile synthesis of AgNPs on reduced graphene oxide for highly sensitive simultaneous detection of heavy metal ions

Silver nanoparticles grown on reduced graphene oxide (AgNPs/RGO) were successfully synthesized via a facile in situ method.

Fluorescent silver nanoparticle based highly sensitive immunoassay for early detection of HIV infection

Fluorescent silver nanoparticles have been employed in an immunoassay to detect HIV p24 antigen with high sensitivity in the linear range of 10–1000 pg mL⁻¹.

Hydrothermal Fabrication of Silver Nanowires-Silver Nanoparticles-Graphene Nanosheets Composites in Enhancing Electrical Conductive Performance of Electrically Conductive Adhesives

Silver nanowires-silver nanoparticles-graphene nanosheets (AgNWs-AgNPs-GN) hybrid nanomaterials were fabricated through a hydrothermal method by using glucose as a green reducing agent. The charge carriers of AgNWs-AgNPs-GN passed through defect regions in the GNs rapidly with the aid of the AgNW and AgNP building blocks, leading to high electrical conductivity of electrically conductive adhesives (ECA) filled with AgNWs-AgNPs-GN. The morphologies of synthesized AgNWs-AgNPs-GN hybrid nanomaterials were characterized by field emission scanning electron microscope (FESEM), and high resolution transmission electron microscopy (HRTEM). X-ray diffraction (XRD) and laser confocal micro-Raman spectroscopy were used to investigate the structure of AgNWs-AgNPs-GN. The resistance of cured ECAs was investigated by the four-probe method. The results indicated AgNWs-AgNPs-GN hybrid nanomaterials exhibited excellent electrical properties for decreasing the resistivity of electrically conductive adhesives (ECA). The resistivity of ECA was 3.01 × 10⁻⁴ Ω·cm when the content of the AgNWs-AgNPs-GN hybrid nanomaterial was 0.8 wt %.

Inorganic arsenic speciation by differential pulse anodic stripping voltammetry using thoria nanoparticles-carbon paste electrodes

Two novel thoria (ThO2) nanoparticles-carbon paste electrodes were used to evaluate an anodic stripping voltammetric method for the direct determination of arsenite and total inorganic arsenic (arsenite plus arsenate) in water samples. The effect of Ag((I)), Cu((II)), Hg((II)), Sb((III)) and Se((IV)) ions on the electrochemical response of arsenic was assayed. The developed electroanalytical method offers a rapid procedure with improved analytical characteristics including good repeatability (3.4%) at low As((III)) concentrations, high selectivity, lower detection limit (0.1 μg L(-1)) and high sensitivity (0.54 μA μg(-1) L). The analytical capability of the optimized method was demonstrated by the determination of arsenic in certified reference materials (trace elements in natural water, trace elements in water and coal fly ash).

Fluorometric sensing of ultralow As(III) concentrations using Ag doped hollow CdS/ZnS bi-layer nanoparticles

Arsenic poisoning from drinking water has been an important global issue in recent years. Because of the high level toxicity of arsenic to human health, an easy, inexpensive, low level and highly selective detection technique is of great importance to take any early precautions. This study reports the synthesis of Ag doped hollow CdS/ZnS bi-layer (Ag-h-CdS/ZnS) nanoparticles for the easy fluorometric determination of As(iii) ions in the aqueous phase. The hollow bi-layer structures were synthesized by a sacrificial core method using AgBr as the sacrificial core and the core was removed by dissolution in an ammonium hydroxide solution. The synthesized nanoparticles were characterized using different instrumental techniques. A good linear relationship was obtained between fluorescence quenching intensity and As(iii) concentration in the range of 0.75-22.5 μg L(-1) at neutral pH with a limit of detection as low as 0.226 μg L(-1).

Determination of malachite green and leucomalachite green based on electrochemiluminescence of Ru(bpy)32+ at graphene oxide modified glassy carbon electrodes

An electrochemiluminescence (ECL) method for the determination of malachite green (MG) and leucomalachite green (LMG) has been established based on ECL of Ru(bpy)₃²⁺ at the GO-modified GCE.

Nanomaterials-based electrochemical detection of chemical contaminants

Recent advances in the development of nanomaterials-based electrochemical sensors for environmental monitoring and food safety applications are assessed.