Adsorption of soft particles at fluid interfaces

Colloidal and interfacial properties of spray dried pulse protein-blueberry polyphenol particles in model dispersion systems

The phytochemical composition and physicochemical attributes of polyphenol-enriched protein particle ingredients produced with pulse proteins (e.g. chickpea protein, pea protein, and a chickpea-pea protein blend) and polyphenols recovered from wild blueberry pomace were investigated for colloidal and interfacial properties. Anthocyanins were the major polyphenol fraction (27.74-36.47 mg C3G/g) of these polyphenol-rich particles (44.95-62.08 mg GAE/g). Dispersions of pea protein-polyphenol particles showed a superior phase stability before and after heat treatment compared to the chickpea pea protein-polyphenol system. This observation was independent of the added amount of NaCl in the dispersion. In general, at quasi equilibrium state, pulse protein-polyphenol particles and parental pulse protein ingredients showed similar oil-water interfacial tension. However, pea protein-polyphenol particles demonstrated a reduced diffusion-driven oil-water interfacial adsorption rate constant compared to the parental pea protein ingredient. Overall, the obtained results suggest application potential of pea protein-polyphenol particles as a functional food/beverage ingredient.

Amphiphilic Nanogels as Versatile Stabilizers for Pickering Emulsions

Pickering emulsions (PEs) are stabilized by particles at the water/oil interface and exhibit superior long-term stability compared to emulsions with molecular surfactants. Among colloidal stabilizers, nano/microgels facilitate emulsification and can introduce stimuli responsiveness. While increasing their hydrophobicity is connected to phase inversion from oil-in-water (O/W) to water-in-oil (W/O) emulsions, a predictive model to relate this phase inversion to the molecular structure of the nano/microgel network remains missing. Addressing this challenge, we developed a library of amphiphilic nanogels (ANGs) that enable adjusting their hydrophobicity while maintaining similar colloidal structures. This enabled us to systematically investigate the influence of network hydrophobicity on emulsion stabilization. We found that W/O emulsions are preferred with increasing ANG hydrophobicity, oil polarity, and oil/water ratio. For nonpolar oils, increasing emulsification temperature enabled the formation of W/O PEs that are metastable at room temperature. We connected this behavior to interfacial ANG adsorption kinetics and quantified ANG deformation and swelling in both phases via atomic force microscopy. Importantly, we developed a quantitative method to predict phase inversion by the difference in Flory-Huggins parameters between ANGs with water and oil (χwater - χoil). Overall, this study provides crucial structure-property relations to assist the design of nano/microgels for advanced PEs.

Nanocrystal Assemblies: Current Advances and Open Problems

We explore the potential of nanocrystals (a term used equivalently to nanoparticles) as building blocks for nanomaterials, and the current advances and open challenges for fundamental science developments and applications. Nanocrystal assemblies are inherently multiscale, and the generation of revolutionary material properties requires a precise understanding of the relationship between structure and function, the former being determined by classical effects and the latter often by quantum effects. With an emphasis on theory and computation, we discuss challenges that hamper current assembly strategies and to what extent nanocrystal assemblies represent thermodynamic equilibrium or kinetically trapped metastable states. We also examine dynamic effects and optimization of assembly protocols. Finally, we discuss promising material functions and examples of their realization with nanocrystal assemblies.

Peculiarities of Emulsions Stabilized by Stimuli-Responsive Interpenetrating Polymeric Network Microgels

Emulsions have become a crucial product form in various industries in modern times. Expanding the class of substances used to stabilize emulsions can improve their stability or introduce new properties. Particularly, the use of stimuli-responsive microgels makes it possible to create "smart" emulsions whose stability can be controlled by changing any of the specified stimuli. Thus, finding new ways to stabilize emulsions may broaden their application. In this work, for the first time, we applied microgels based on interpenetrating polymeric networks (IPNs) of poly(N-isopropylacrylamide) (PNIPAM) and poly(acrylic acid) (PAA) as stabilizing agents for "oil-in-water" emulsions. We have demonstrated that emulsions stabilized by such soft particles can remain colloidally stable for an extended period, even after being heated up to 40 °C, which is above the lower critical solution temperature (LCST) of PNIPAM. On the contrary, the emulsions stabilized by PNIPAM homopolymer microgels were broken upon heating. To understand the stabilization mechanism of the emulsions, mesoscopic computer simulations were performed to study the IPN microgels at the liquid-liquid interface. The simulations demonstrated that when the first subnetwork (PNIPAM) collapses, the particle adopts a flattened core-shell morphology with a highly swollen PAA-rich shell and a collapsed PNIPAM-rich core. Unlike its PNIPAM homopolymer counterpart, the IPN microgel maintains its three-dimensional shape, which provides stability to the microgel-based emulsions over a wide range of temperatures. Our combined findings could be useful in developing new approaches to emulsions' storage, biphasic catalysis, and lubrication of mechanisms in various operating and climatic conditions.

Pea protein [Pisum sativum] as stabilizer for oil/water emulsions

A map of stability for various water/oil/pea protein compositions has been plotted from the numerous reported results. Two clear regions of stability were identified. High internal oil phase emulsions with 70-80%, v/v oil content stabilized by total pea protein concentration <2.5%, w/v showed stability. Low oil content of 10-30%, v/v for a range of total pea protein concentrations >0.5%, w/v have also been identified as stable. Intermediate oil content and pea protein concentrations >4% w/v are unexplored regions and are likely to be areas of fruitful future research. The wide range of stability suggests that different stabilization mechanisms could be important for different compositions and careful consideration has to be taken to avoid oversimplification. Both stabilization with particles, i.e. Pickering emulsions, and protein unfolding have been suggested as mechanisms. The diverse way of describing stability makes it difficult to intercompare results in different studies. A summary of different oil types used have been presented and several properties such as dynamic viscosity, density, the dielectric constant and interfacial tension have been summarized for common vegetable oils. The type of vegetable oil and emulsion preparation techniques were seen to have rather little effect on emulsion stability. However, the different extraction methods and processing of the pea material had more effect, which could be attributed to changing composition of different proteins and to the states of aggregation and denaturing. Careful consideration has to be taken in the choice of extraction method and an increased understanding of what contributes to the stability is desirable for further progress in research and eventual product formulation.

Interactions between interfaces dictate stimuli-responsive emulsion behaviour

Stimuli-responsive emulsions offer a dual advantage, combining long-term storage with controlled release triggered by external cues such as pH or temperature changes. This study establishes that thermo-responsive emulsion behaviour is primarily determined by interactions between, rather than within, interfaces. Consequently, the stability of these emulsions is intricately tied to the nature of the stabilizing microgel particles - whether they are more polymeric or colloidal, and the morphology they assume at the liquid interface. The colloidal properties of the microgels provide the foundation for the long-term stability of Pickering emulsions. However, limited deformability can lead to non-responsive emulsions. Conversely, the polymeric properties of the microgels enable them to spread and flatten at the liquid interface, enabling stimuli-responsive behaviour. Furthermore, microgels shared between two emulsion droplets in flocculated emulsions facilitate stimuli-responsiveness, regardless of their internal architecture. This underscores the pivotal role of microgel morphology and the forces they exert on liquid interfaces in the control and design of stimuli-responsive emulsions and interfaces.

Compression and Ordering of Hollow Microgels in Monolayers Formed at Liquid-Liquid Interfaces

Monolayers of polymer microgels with a spherical cavity adsorbed at the liquid-liquid interface were studied using mesoscopic computer simulations. One liquid, named water, was always considered as a good solvent, while the microgel solubility in the second liquid, named oil, was varied. The symmetric and asymmetric cases of vanishing and the strong differences in solubility between the network particles and the liquids were considered. The simulations provided us with an insight into the shape and volume changes of the microgels upon compression, making it possible to relate the response of the individual network with the collective order and structure of the monolayer. Similar to regular microgels, the compression of the monolayer of hollow particles led to a decrease in lateral sizes accompanied by shape transformation from a flattened to a nearly spherical shape. However, the presence of a cavity filled with solvent caused some unique differences in the behavior of the system. The adsorption pathway of hollow microgels at the liquid interface predefines: (a) the position of the particles with respect to the interface and (b) the structure of the monolayer. A striking discovery is that in the symmetric case of similar solubility of the microgel in both liquids, it is possible to produce a monolayer in which one part of the network faces the aqueous phase and the other part faces the oil phase. The polymer concentration profiles plotted along the normal to the interface reveal a redistribution of polymeric mass of the microgels relative to the interface, distinguishing between the microgels whose cavities are filled with water and oil, respectively. Moreover, the ratio between the microgels faced in water and oil does not change upon compression and predetermines the response and order of the monolayer.

Triple-line dynamics of a soft colloid-laden drop on a hydrophobic surface

Evaporation of fluid from a pinned drop placed on solid surface proceeds via constant contact radius (CCR) mode, with a continuous reduction in the contact angle. The reduction of contact angle leads to an imbalance of interfacial tensions at the three-phase contact line. When the unbalanced force is sufficiently strong, the drop slips from the pinned contact line and slides inward. Depinning of the drop alters the mode of evaporation to constant contact angle (CCA) mode till it repins onto the surface. The change in evaporation mode from CCR to CCA is usually achieved by tuning the pinning energy barrier by controlling the surface properties of the substrate. Here, we demonstrate that the evaporation mode can be controlled by solely tailoring the surface tension of the drop, which is achieved in microgel particle-laden sessile drops that show spontaneous adsorption of microgels to the air/water interface, leading to a decrease in the interfacial tension. We show that droplets containing a sufficient number of microgels evaporate predominantly in CCR mode even on a hydrophobic surface, and the contact line remains pinned throughout the evaporation of the drop. Interestingly, the contact line dynamics can be controlled by tuning the softness of the microgels and the particle concentration in the drops.

Biopolymer-based pickering high internal phase emulsions: Intrinsic composition of matrix components, fundamental characteristics and perspective

Pickering HIPEs have received tremendous attention in recent years due to their superior stability and unique solid-like and rheological properties. Biopolymer-based colloidal particles derived from proteins, polysaccharides and polyphenols have been demonstrated to be safety stabilizers for the construction of Pickering HIPEs, which can meet the demands of consumers for "all-natural" products and provide "clean-label" foods. Furthermore, the functionality of these biopolymers can be further extended by forming composite, conjugated and multi-component colloidal particles, which can be used to modulate the properties of the interfacial layer, thereby adjusting the performance and stability of Pickering HIPEs. In this review, the factors affecting the interfacial behavior and adsorption characteristics of colloidal particles are discussed. The intrinsic composition of matrix components and fundamental characteristics of Pickering HIPEs are emphatically summarized, and the emerging applications of Pickering HIPEs in the food industry are reviewed. Inspired by these findings, future perspectives concerning this field are also put forward, including (1) the exploration of the interactions between biopolymers used to produce Pickering HIPEs and target food ingredients, and the influence of the added biopolymers on the flavor and mouthfeel of the products, (2) the investigation of the digestion properties of Pickering HIPEs under oral administration, and (3) the fabrication of stimulus-responsive or transparent Pickering HIPEs. This review will give a reference for exploring more natural biopolymers for Pickering HIPEs application development.

Adsorption and Assembly of Octenyl Succinic Anhydride Starch/Chitosan Electrostatic Complexes at Oil-Water Interface

Biopolymer electrostatic complexes are popular Pickering stabilizers whose structures greatly affect their interfacial properties. This study comprehensively demonstrated the interfacial adsorption and assembly of dissolved octenyl succinic anhydride (OSA) starch (OSA-D)/chitosan (CS) electrostatic complexes with different structures through complementary characterization methods. We found that compared with single-component systems, OSA-D/CS complexes exhibited significantly increased wetting stability and adsorption rate to the interface, which was reinforced by molecular dynamics simulations. Their soft structures and the entanglement of molecular chains led to the formation of thick and highly viscoelastic multilayer adsorbed films, which greatly resisted deformation against shearing forces. The adsorption and assembly of the complexes were strongly influenced by OSA-D/CS ratios and pH, which could be related to the different interfacial interaction strengths. Overall, the electrostatic complexation, structural characteristics, and interfacial properties of OSA-D/CS complexes were well related, thereby providing valuable information for the regulation of controlled interfaces and bulk system properties.

Competitive Adsorption of Interfacially Active Nanoparticles and Anionic Surfactant at the Crude Oil-Water Interface

The interfacial activity of poly(N-isopropylacrylamide) (pNIPAM) nanoparticles in the absence and presence of an anionic surfactant (sodium dodecyl sulfate, SDS) was studied at a crude oil-water interface. Both species are interfacially active and can lower the interfacial tension, but when mixed together, the interfacial composition was found to depend on the aging time and total component concentration. With the total component concentration less than 0.005 wt %, the reduced interfacial tension by pNIPAM was greater than SDS; thus, pNIPAM has a greater affinity to partition at the crude oil-water interface. However, the lower molecular weight (smaller molecule) of SDS compared to pNIPAM meant that it rapidly partitioned at the oil-water interface. When mixed, the interfacial composition was more SDS-like for low total component concentrations (≤ 0.001 wt %), while above, the interfacial composition was more pNIPAM-like, similar to the single component response. Applying a weighted arithmetic mean approach, the surface-active contribution (%) could be approximated for each component, pNIPAM and SDS. Even though SDS rapidly partitioned at the oil-water interface, it was shown to be displaced by the pNIPAM nanoparticles, and for the highest total component concentration, pNIPAM nanoparticles were predominantly contributing to the reduced oil-water interfacial tension. These findings have implications for the design and performance of fluids that are used to enhance crude oil production from reservoirs, particularly highlighting the aging time and component concentration effects to modify interfacial tensions.

Multiphase displacement manipulated by micro/nanoparticle suspensions in porous media via microfluidic experiments: From interface science to multiphase flow patterns

Multiphase displacement in porous media can be adjusted by micro/nanoparticle suspensions, which is widespread in many scientific and industrial contexts. Direct visualization of suspension flow dynamics and corresponding multiphase patterns is crucial to understanding displacement mechanisms and eventually optimizing these processes in geological, biological, chemical, and other engineering systems. However, suspension flow inside the opaque realistic porous media makes direct observation challenging. The advances in microfluidic experiments have provided us with alternative methods to observe suspension influence on the interface and multiphase flow behaviors at high temporal and spatial resolutions. Macroscale processes are controlled by microscale interfacial behaviors, which are affected by multiple physical factors, such as particle adsorption, capillarity, and hydrodynamics. These properties exerted on the suspension flow in porous media may lead to interesting interfacial phenomena and new displacement consequences. As an underpinning science, understanding and controlling the suspension transport process from interface to flow patterns in porous media is critical for a lower operating cost to improve resource production while reducing harmful emissions and other environmental impacts. This review summarizes the basic properties of different micro/nanoparticle suspensions and the state-of-the-art microfluidic techniques for displacement research activities in porous media. Various suspension transport behaviors and displacement mechanisms explored by microfluidic experiments are comprehensively reviewed. This review is expected to boost both experimental and theoretical understanding of suspension transport and interfacial interaction processes in porous media. It also brings forward the challenges and opportunities for future research in controlling complex fluid flow in porous media for diverse applications.

Interfacial rheology of model water-air microgels laden interfaces: Effect of cross-linking

HYPOTHESIS

The mechanical properties of model air/water interfaces covered by poly(N-isopropylacrylamide) microgels depend on the microgels deformability or in other words on the amount of cross-linker added during synthesis.

EXPERIMENTS

The study is carried out by measuring the apparent dilational, the compression and the shear moduli using three complementary methods: (1) the pendant drop method with perturbative areas, (2) the Langmuir trough compression, and (3) shear rheology using a double wall ring cell mounted onto a Langmuir through.

FINDINGS

In the range of surface coverages studied, the interfaces exhibit a solid-like behavior and elasticity goes through a maximum as a function of the surface pressure. This is observable whatever the investigation method. This maximum elasticity depends on the microgel deformability: the softer the microgels the higher the value of the moduli. The mechanical behavior of model interfaces is discussed, taking into account the core-shell structure of the particles and their packing at the interface.

In situ imaging of the three-dimensional shape of soft responsive particles at fluid interfaces by atomic force microscopy

The reconfiguration of individual soft and deformable particles upon adsorption at a fluid interface underpins many aspects of their dynamics and interactions, ultimately regulating the properties of monolayers of relevance for applications. In this work, we demonstrate that atomic force microscopy can be used for the in situ reconstruction of the three-dimensional conformation of model poly(N-isopropylacrylamide) microgels adsorbed at an oil-water interface. We image the particle topography from both sides of the interface to characterize its in-plane deformation and to visualize the occurrence of asymmetric swelling in the two fluids. In addition, the technique enables investigating different fluid phases and particle architectures, as well as studying the effect of temperature variations on particle conformation in situ. We envisage that these results open up an exciting range of possibilities to provide microscopic insights into the single-particle behavior of soft objects at fluid interfaces and into the resulting macroscopic material properties.

Fluid interface-assisted assembly of soft microgels: recent developments for structures beyond hexagonal packing

Microgels adsorb to air/water and oil/water interfaces - a process driven by a significant reduction in interfacial tension. Depending on the available interface area per microgel, strong lateral deformation can be observed. Typically, hexagonally ordered structures appear spontaneously upon contact of the microgel shells. Transfer from the interface to solid substrates gives access to macroscopically sized microgel monolayers that are interesting for photonic and plasmonic studies as well as colloid-based lithography, for example. Significant efforts have been made to understand the phase behavior of microgels at different interfaces and to explore the available parameter space for achieving complex tessellations. In this review, we will discuss the most recent developments in the realization of microgel monolayers with structures beyond hexagonal packing.

Interfacial self-assembly of SiO2-PNIPAM core-shell particles with varied crosslinking density

Spherical particles confined to liquid interfaces generally self-assemble into hexagonal patterns. It was theoretically predicted by Jagla two decades ago that such particles interacting via a soft repulsive potential are able to form complex, anisotropic assembly phases. Depending on the shape and range of the potential, the predicted minimum energy configurations include chains, rhomboid and square phases. We recently demonstrated that deformable core-shell particles consisting of a hard silica core and a soft poly(N-isopropylacrylamide) shell adsorbed at an air/water interface can form chain phases if the crosslinker is primarily incorporated around the silica core. Here, we systematically investigate the interfacial self-assembly behavior of such SiO₂-PNIPAM core-shell particles as a function of crosslinker content and core size. We observe chain networks predominantly at low crosslinking densities and smaller core sizes, whereas higher crosslinking densities lead to the formation of rhomboid packing. We correlate these results with the interfacial morphologies of the different particle systems, where the ability to expand at the interface and form a thin corona at the periphery depends on the degree of crosslinking close to the core. We perform minimum energy calculations based on Jagla-type pair potentials with different shapes of the soft repulsive shoulder. We compare the theoretical phase diagram with experimental findings to infer to which extent the interfacial interactions of the experimental system may be captured by Jagla pair-wise interaction potentials.

High-performance displacement by microgel-in-oil suspension in heterogeneous porous media: Microscale visualization and quantification

HYPOTHESIS

Preferential flow in porous media is commonly encountered and decreases the multiphase displacement efficiency. Here, we synthesized microgel-in-oil in suspension and demonstrated that microgel-in-oil as a novel additive could present self-adaptive transport behavior and introduce a novel multiphase displacement mode for improving displacement efficiency in heterogeneous porous media.

EXPERIMENTS

We investigated the microgel-in-oil formation process and characterized their morphology with fluorescence microscopy and Cryo-SEM. The suspension displacement performance in heterogeneous porous media was evaluated using a microfluidic chip containing a preferential flow pathway (PFP) and a parallel matrix region. The displacement results of microgel-in-oil were compared to plain microgel particles and analyzed from pore-scale particle transport behavior to macroscopic multiphase flow patterns.

FINDINGS

The results show that suspension with moderate microgel-in-oil yields the optimal displacement efficiency. Fewer microgel-in-oil cannot alter the flow direction, while too many microgel-in-oil would block the PFP region. The topological analysis identified that suspensions with moderate microgel-in-oil content could achieve the strongest sweeping and carrying abilities that contribute to the highest displacement efficiency. The synergistic transport of microgel-in-oil and plain microgel particles would result in local pressure fluctuations to divert displacing fluid from PFP into the matrix region, which explains the above flow behavior.

How Softness Matters in Soft Nanogels and Nanogel Assemblies

Softness plays a key role in determining the macroscopic properties of colloidal systems, from synthetic nanogels to biological macromolecules, from viruses to star polymers. However, we are missing a way to quantify what the term "softness" means in nanoscience. Having quantitative parameters is fundamental to compare different systems and understand what the consequences of softness on the macroscopic properties are. Here, we propose different quantities that can be measured using scattering methods and microscopy experiments. On the basis of these quantities, we review the recent literature on micro- and nanogels, i.e. cross-linked polymer networks swollen in water, a widely used model system for soft colloids. Applying our criteria, we address the question what makes a nanomaterial soft? We discuss and introduce general criteria to quantify the different definitions of softness for an individual compressible colloid. This is done in terms of the energetic cost associated with the deformation and the capability of the colloid to isotropically deswell. Then, concentrated solutions of soft colloids are considered. New definitions of softness and new parameters, which depend on the particle-to-particle interactions, are introduced in terms of faceting and interpenetration. The influence of the different synthetic routes on the softness of nanogels is discussed. Concentrated solutions of nanogels are considered and we review the recent results in the literature concerning the phase behavior and flow properties of nanogels both in three and two dimensions, in the light of the different parameters we defined. The aim of this review is to look at the results on micro- and nanogels in a more quantitative way that allow us to explain the reported properties in terms of differences in colloidal softness. Furthermore, this review can give researchers dealing with soft colloids quantitative methods to define unambiguously which softness matters in their compound.

Microgels as globular protein model systems

Understanding globular protein adsorption to fluid interfaces, their interfacial assembly, and structural reorganization is not only important in the food industry, but also in medicine and biology. However, due to their intrinsic structural complexity, a unifying description of these phenomena remains elusive. Herein, we propose N-isopropylacrylamide microgels as a promising model system to isolate different aspects of adsorption, dilatational rheology, and interfacial structure at fluid interfaces with a wide range of interfacial tensions, and compare the results with the ones of globular proteins. In particular, the steady-state spontaneously-adsorbed interfacial pressure of microgels correlates closely to that of globular proteins, following the same power-law behavior as a function of the initial surface tension. However, the dilatational rheology of spontaneously-adsorbed microgel layers is dominated by the presence of a loosely packed polymer corona spread at the interface, and it thus exhibits a similar mechanical response as flexible, unstructured proteins, which are significantly weaker than globular ones. Finally, structurally, microgels reveal a similar spreading and flattening upon adsorption as globular proteins do. In conclusion, microgels offer interesting opportunities to act as powerful model systems to unravel the complex behavior of proteins at fluid interfaces.

Effect of network topology and crosslinker reactivity on microgel structure and ordering at liquid-liquid interface

Polymer microgels synthesized in silico were studied at a liquid-liquid interface via mesoscopic computer simulations and compared to microgels with ideal (diamond-like) structure. The effect of crosslinkers reactivity ratio on the single particle morphology at the interface and monolayer behavior was examined. It was demonstrated that single particles deform into an explicit core-corona morphology when adsorbed at the interface. An increase in the crosslinker reactivity ratio decreased both the deformation ratio and the ratio between the core and corona sizes. Meanwhile, the compression of microgel monolayers revealed the existence of five distinct interparticle contact regimes, which have been observed experimentally in the literature. The crosslinker reactivity ratio appeared to define the compression range in these regimes and the sharpness of the transition between them. In particular, the higher the crosslinker reactivity ratio, the smaller the corona, and in turn, the narrower the range of the intermediate regime comprising both core-core and corona-corona contacts. The obtained results demonstrate that the more realistic model of microgels synthesized via precipitation polymerization allows for a more accurate prediction of the properties of the microgels at a liquid-liquid interface in comparison to the conventional diamond-like lattice model.

A broad perspective to particle-laden fluid interfaces systems: from chemically homogeneous particles to active colloids

Particles adsorbed to fluid interfaces are ubiquitous in industry, nature or life. The wide range of properties arising from the assembly of particles at fluid interface has stimulated an intense research activity on shed light to the most fundamental physico-chemical aspects of these systems. These include the mechanisms driving the equilibration of the interfacial layers, trapping energy, specific inter-particle interactions and the response of the particle-laden interface to mechanical perturbations and flows. The understanding of the physico-chemistry of particle-laden interfaces becomes essential for taking advantage of the particle capacity to stabilize interfaces for the preparation of different dispersed systems (emulsions, foams or colloidosomes) and the fabrication of new reconfigurable interface-dominated devices. This review presents a detailed overview of the physico-chemical aspects that determine the behavior of particles trapped at fluid interfaces. This has been combined with some examples of real and potential applications of these systems in technological and industrial fields. It is expected that this information can provide a general perspective of the topic that can be exploited for researchers and technologist non-specialized in the study of particle-laden interfaces, or for experienced researcher seeking new questions to solve.

Soft Colloidal Particles at Fluid Interfaces

The assembly of soft colloidal particles at fluid interfaces is reviewed in the present paper, with emphasis on the particular case of microgels formed by cross-linked polymer networks. The dual polymer/colloid character as well as the stimulus responsiveness of microgel particles pose a challenge in their experimental characterization and theoretical description when adsorbed to fluid interfaces. This has led to a controversial and, in some cases, contradictory picture that cannot be rationalized by considering microgels as simple colloids. Therefore, it is necessary to take into consideration the microgel polymer/colloid duality for a physically reliable description of the behavior of the microgel-laden interface. In fact, different aspects related to the above-mentioned duality control the organization of microgels at the fluid interface, and the properties and responsiveness of the obtained microgel-laden interfaces. This works present a critical revision of different physicochemical aspects involving the behavior of individual microgels confined at fluid interfaces, as well as the collective behaviors emerging in dense microgel assemblies.

Influence of the interfacial tension on the microstructural and mechanical properties of microgels at fluid interfaces

Microgels are soft colloidal particles constituted by cross-linked polymer networks with a high potential for applications. In particular, after adsorption at a fluid interface, interfacial tension provides two-dimensional (2D) confinement for microgel monolayers and drives the reconfiguration of the particles, enabling their deployment in foam and emulsion stabilization and in surface patterning for lithography, sensing and optical materials. However, most studies focus on systems of fluids with a high interfacial tension, e.g. alkanes/ or air/water interfaces, which imparts similar properties to the assembled monolayers. Here, instead, we compare two organic fluid phases, hexane and methyl tert-butyl ether, which have markedly different interfacial tension (γ) values with water and thus tune the deformation of adsorbed microgels. We rationalize how γ controls the single-particle morphology, which consequently modulates the structural and mechanical response of the monolayers at varying interfacial compression. Specifically, when γ is low, the microgels are less deformed within the interface plane and their polymer networks can rearrange more easily upon lateral compression, leading to softer monolayers. Selecting interfaces with different surface energy offers an additional control to customize the 2D assembly of soft particles, from the fine-tuning of particle size and interparticle spacing to the tailoring of mechanical properties.

Non-Covalent Reconfigurable Microgel Colloidosomes with a Well-Defined Bilayer Shell

Microgels are extremely interfacially active and are widely used to stabilize emulsions. However, they are commonly used to stabilize oil-in-water emulsions due to their intrinsic hydrophilicity and initially dispersed in water. In addition, there have been no attempts to control microgel structural layers that are formed at the interface and as a result it limits applications of microgel in advanced materials. Here, we show that by introducing octanol into poly(N-isopropylacrylamide-co-methacrylic acid) (PNIPAM-co-MAA) microgels, octanol-swollen microgels can rapidly diffuse from the initially dispersed oil phase onto the water droplet surface. This facilitates the formation of microgel-laden interfacial layers with strong elastic responses and also generates stable inverse water-in-oil Pickering emulsions. These emulsions can be used as templates to produce microgel colloidosomes, herein termed ‘microgelsomes’, with shells that can be fine-tuned from a particle monolayer to a well-defined bilayer. The microgelsomes can then be used to encapsulate and/or anchor nanoparticles, proteins, vitamin C, bio-based nanocrystals or enzymes. Moreover, the programmed release of these substances can be achieved by using ethanol as a trigger to mediate shell permeability. Thus, these reconfigurable microgelsomes with a microgel-bilayer shell can respond to external stimuli and demonstrate tailored properties, which offers novel insights into microgels and promise wider application of Pickering emulsions stabilized by soft colloids.

Inverse W/O Pickering emulsions and reconfigurable microgelsomes with a well-defined bilayer structure are prepared from octanol-swollen PNIPAM-co-MAA microgels and the combination of binary microgels, which promise wider application of soft colloids.

Defined core-shell particles as the key to complex interfacial self-assembly

The two-dimensional self-assembly of colloidal particles serves as a model system for fundamental studies of structure formation and as a powerful tool to fabricate functional materials and surfaces. However, the prevalence of hexagonal symmetries in such self-assembling systems limits its structural versatility. More than two decades ago, Jagla demonstrated that core-shell particles with two interaction length scales can form complex, nonhexagonal minimum energy configurations. Based on such Jagla potentials, a wide variety of phases including cluster lattices, chains, and quasicrystals have been theoretically discovered. Despite the elegance of this approach, its experimental realization has remained largely elusive. Here, we capitalize on the distinct interfacial morphology of soft particles to design two-dimensional assemblies with structural complexity. We find that core-shell particles consisting of a silica core surface functionalized with a noncrosslinked polymer shell efficiently spread at a liquid interface to form a two-dimensional polymer corona surrounding the core. We controllably grow such shells by iniferter-type controlled radical polymerization. Upon interfacial compression, the resulting core-shell particles arrange in well-defined dimer, trimer, and tetramer lattices before transitioning into complex chain and cluster phases. The experimental phase behavior is accurately reproduced by Monte Carlo simulations and minimum energy calculations, suggesting that the interfacial assembly interacts via a pairwise-additive Jagla-type potential. By comparing theory, simulation, and experiment, we narrow the Jagla g-parameter of the system to between 0.9 and 2. The possibility to control the interaction potential via the interfacial morphology provides a framework to realize structural features with unprecedented complexity from a simple, one-component system.

The Force Required to Detach a Rotating Particle from a Liquid-Fluid Interface

The force required to detach a particle from a liquid-fluid interface is a direct measure of the capillary adhesion between the particle and the interface. Analytical expressions for the detachment force are available but are limited to nonrotating particles. In this work, we derive analytical expressions for the force required to detach a rotating spherical particle from a liquid-fluid interface. Our theory predicts that the rotation reduces the detachment force when there is a finite contact angle hysteresis between the particle and the liquid. For example, the force required to detach a particle with an advancing contact angle of 120° and a receding contact angle of 80° (e.g., polydimethylsiloxane particle at a water-air interface) is expected to be 25% lower when the particle rotates while it is detached.

Exploring water in oil emulsions simultaneously stabilized by solid hydrophobic silica nanospheres and hydrophilic soft PNIPAM microgel

A general drawback of microgels is that they do not stabilize water-in-oil (w/o) emulsions of non-polar oils. Simultaneous stabilization with solid hydrophobic nanoparticles and soft hydrophilic microgels overcomes this problem. For a fundamental understanding of this synergistic effect the use of well defined particle systems is crucial. Therefore, the present study investigates the stabilization of water droplets in a highly non-polar oil phase using temperature responsive, soft and hydrophilic PNIPAM microgel particles (MGs) and solid and hydrophobic silica nanospheres (SNs) simultaneously. The SNs are about 20 times smaller than the MGs. In a multiscale approach the resulting emulsions are studied from the nanoscale particle properties over microscale droplet sizes to macroscopic observations. The synergy of the particles allows the stabilization of water-in-oil (w/o) emulsions, which was not possible with MGs alone, and offers a larger internal interface than the stabilization with SNs alone. Furthermore, the incorporation of hydrophilic MGs into a hydrophobic particle layer accelerates the emulsions sedimentation speed. Nevertheless, the droplets are still sufficiently protected against coalescence even in the sediment and can be redispersed by gentle shaking. Based on droplet size measurements and cryo-SEM studies we elaborate a model, which explains the found phenomena.

Particle-laden fluid/fluid interfaces: physico-chemical foundations

Particle-laden fluid/fluid interfaces are ubiquitous in academia and industry, which has fostered extensive research efforts trying to disentangle the physico-chemical bases underlying the trapping of particles to fluid/fluid interfaces as well as the properties of the obtained layers. The understanding of such aspects is essential for exploiting the ability of particles on the stabilization of fluid/fluid interface for the fabrication of novel interface-dominated devices, ranging from traditional Pickering emulsions to more advanced reconfigurable devices. This review tries to provide a general perspective of the physico-chemical aspects associated with the stabilization of interfaces by colloidal particles, mainly chemical isotropic spherical colloids. Furthermore, some aspects related to the exploitation of particle-laden fluid/fluid interfaces on the stabilization of emulsions and foams will be also highlighted. It is expected that this review can be used for researchers and technologist as an initial approach to the study of particle-laden fluid layers.

Capillary Torque on a Particle Rotating at an Interface

Small particles attach to liquid-fluid interfaces due to capillary forces. The influence of rotation on the capillary force is largely unexplored, despite being relevant whenever particles roll at a liquid-fluid interface or on a moist solid. Here, we demonstrate that due to contact angle hysteresis, a particle needs to overcome a resistive capillary torque to rotate at an interface. We derive a general model for the capillary torque on a spherical particle. The capillary torque is given by M = γRLk(cos Θ_R - cos Θ_A), where γ is the interfacial tension, R is the radius of the particle, L is the diameter of the contact line, k = 24/π³ is a geometrical constant, and Θ_R and Θ_A are the receding and advancing contact angles, respectively. The expression for the capillary torque (normalized by the radius of the particle) is equivalent to the expression for the friction force that a drop experiences when moving on a flat surface. Our theory predicts that capillary torque reduces the mobility of wet granular matter and prevents small (nano/micro) particles from rotating when they are in Brownian motion at an interface.

Interface-induced hysteretic volume phase transition of microgels: simulation and experiment

Thermo-responsive microgel particles can exhibit a drastic volume shrinkage upon increasing the solvent temperature. Recently we found that the spreading of poly(N-isopropylacrylamide) (PNiPAm) microgels at a liquid interface under the influence of surface tension hinders the temperature-induced volume phase transition. In addition, we observed a hysteresis behavior upon temperature cycling, i.e. a different evolution in microgel size and shape depending on whether the microgel was initially adsorbed to the interface in expanded or collapsed state. Here, we model the volume phase transition of such microgels at an air/water interface by monomer-resolved Brownian dynamics simulations and compare the observed behavior with experiments. We reproduce the experimentally observed hysteresis in the microgel dimensions upon temperature variation. Our simulations did not observe any hysteresis for microgels dispersed in the bulk liquid, suggesting that it results from the distinct interfacial morphology of the microgel adsorbed at the liquid interface. An initially collapsed microgel brought to the interface and subjected to subsequent swelling and collapsing (resp. cooling and heating) will end up in a larger size than it had in the original collapsed state. Further temperature cycling, however, only shows a much reduced hysteresis, in agreement with our experimental observations. We attribute the hysteretic behavior to a kinetically trapped initial collapsed configuration, which relaxes upon expanding in the swollen state. We find a similar behavior for linear PNiPAm chains adsorbed to an interface. Our combined experimental - simulation investigation provides new insights into the volume phase transition of PNiPAm materials adsorbed to liquid interfaces.

Collapse-induced phase transitions in binary interfacial microgel monolayers

Microgels, consisting of a swollen polymer network, exhibit a more complex self-assembly behavior compared to incompressible colloidal particles, because of their ability to deform at a liquid interface or collapse upon compression. Here, we investigate the collective phase behavior of two-dimensional binary mixtures of microgels confined at the air/water interface. We use stimuli-responsive poly(N-isopropylacrylamide) microgels with different crosslinking densities, and therefore different morphologies at the interface. We find that the minority microgel population introduces lattice defects in the ordered phase of the majority population, which, in contrast to bulk studies, do not heal out by partial deswelling to accommodate in the lattice. We subsequently investigate the interfacial phase behavior of these binary interfacial assemblies under compression. The binary system exhibits three distinct isostructural solid-solid phase transitions, during which the coronae between two small particles collapse first, followed by the collapse between small-large and large-large microgel pairs. A similar hierarchy of phase transitions is found for mixtures of microgels and core-shell particles. Simulations based on augmented potentials qualitatively reproduce the experimentally observed phase transitions. We rationalize the presence of this hierarchy in phase transitions from differences in the interfacial morphology between the species: the larger coronae of softer (and therefore larger) microgels provide a higher resistance to phase transitions compared to the smaller coronae of the more crosslinked microgels and core-shell particles. The control of phase transitions via the molecular architecture further allows the formation of characteristic, flower-like defects by introducing particles with "weaker" coronae that are more prone to collapse with their neighboring particles. Our findings underline the dominating role of the corona for interfacial microgel assemblies, which acts as an energy barrier, shifting the collapse to higher surface pressures.

Soft Particles at Liquid Interfaces: From Molecular Particle Architecture to Collective Phase Behavior

Soft particles such as microgels can undergo significant and anisotropic deformations when adsorbed to a liquid interface. This, in turn, leads to a complex phase behavior upon compression. To date, experimental efforts have predominantly provided phenomenological links between microgel structure and resulting interfacial behavior, while simulations have not been entirely successful in reproducing experiments or predicting the minimal requirements for the desired phase behavior. Here, we develop a multiscale framework to link the molecular particle architecture to the resulting interfacial morphology and, ultimately, to the collective interfacial phase behavior. To this end, we investigate interfacial morphologies of different poly(N-isopropylacrylamide) particle systems using phase-contrast atomic force microscopy and correlate the distinct interfacial morphology with their bulk molecular architecture. We subsequently introduce a new coarse-grained simulation method that uses augmented potentials to translate this interfacial morphology into the resulting phase behavior upon compression. The main novelty of this method is the possibility to efficiently encode multibody interactions, the effects of which are key to distinguishing between heterostructural (anisotropic collapse) and isostructural (isotropic collapse) phase transitions. Our approach allows us to qualitatively resolve existing discrepancies between experiments and simulations. Notably, we demonstrate the first in silico account of the two-dimensional isostructural transition, which is frequently found in experiments but elusive in simulations. In addition, we provide the first experimental demonstration of a heterostructural transition to a chain phase in a single-component system, which has been theoretically predicted decades ago. Overall, our multiscale framework provides a phenomenological bridge between physicochemical soft-particle characteristics at the molecular scale and nanoscale and the collective self-assembly phenomenology at the macroscale, serving as a stepping stone toward an ultimately more quantitative and predictive design approach.

Capillary forces drive buckling, plastic deformation, and break-up of 3D printed beams

Capillary forces acting at the interfaces of soft materials lead to deformations over the scale of the elastocapillary length. When surface stresses exceed a material's yield stress, a plastocapillary effect is expected to arise, resulting in yielding and plastic deformation. Here, we explore the interfacial instabilities of 3D-printed fluid and elastic beams embedded within viscoelastic fluids and elastic solid support materials. Interfacial instabilities are driven by the immiscibility between the paired phases or their solvents. We find that the stability of an embedded structure is predicted from the balance between the yield stress of the elastic solid, τ_y, the apparent interfacial tension between the materials, γ', and the radius of the beam, r, such that τ_y > γ'/r. When the capillary forces are sufficiently large, we observe yielding and failure of the 3D printed beams. Furthermore, we observe new coiling and buckling instabilities emerging when elastic beams are embedded within viscous fluid support materials. The coiling behavior appear analogous to elastic rope coiling whereas the buckling instability follows the scaling behavior predicted from Euler-Bernoulli beam theory.

Evaporative self-assembly of the binary mixture of soft colloids

We have reported experimental studies on the self-assembly and degree of ordering of a binary mixture of soft colloids in monolayer deposits obtained by controlled evaporation. A sessile drop containing soft colloids is evaporated on a solid surface to achieve a loosely-packed two-dimensional deposit with a hexagonal arrangement. The soft microgel particles possess a hard core with a compliant corona, which plays a crucial role in retaining the crystallinity of the binary particle monolayer. The ordered arrangement of the binary mixture is observed even when the bulk diameter of one type of particle is 25% higher than the other, irrespective of their mixing ratio (1 : 3, 1 : 1, and 3 : 1). The microgel particles of both sizes are found to be homogeneously distributed throughout the deposit, completely suppressing the size-dependent particle segregation. Furthermore, in contrast to the self-assembly of bidisperse hard colloids, wherein the lattice distorts to accommodate particles of disparate sizes, in soft colloids, the particles deform at the interface to preserve the crystalline lattice. Moreover, unlike the gradual order-to-disorder transition observed in the deposits consisting of monodisperse microgel particles, the deposits of a binary mixture of microgels exhibit no noticeable trend. The areal disorder parameter, pair correlation function and the shape factor which quantifies the local ordering of particles in the deposit indicate the absence of a distinct order-to-disorder transition for the binary mixtures.

Sunflower Proteins at Air-Water and Oil-Water Interfaces

The adsorption of a sunflower protein extract at two air-water and oil-water interfaces is investigated using tensiometry, dilational viscoelasticity, and ellipsometry. For both interfaces, a three step mechanism was evidenced thanks to master curve representations of the data taken at different aging times and protein concentrations. At short times, a diffusion limited adsorption of proteins at interfaces is demonstrated. First, a two-dimensional protein film is formed with a partition of the polypeptide chains in the two phases that depends strongly on the nature of the hydrophobic phase: most of the film is in the aqueous phase at the air-water interface, while it is mostly in the organic phase at the oil-water interface. Then a three-dimensional saturated monolayer of proteins is formed. At short times, adsorption mechanisms are analogous to those found with typical globular proteins, while strong divergences are observed at longer adsorption times. Following the saturation step, a thick layer expands in the aqueous phase and appears associated with the release of large objects in the bulk. The kinetic evolution of this second layer is compatible with a diffusion limited adsorption of the minor population of polymeric complexes with hydrodynamic radius R_H ∼ 80 nm, evidenced in equilibrium with hexameric globulins (R_H ∼ 6 nm) in solution. These complexes could result from the presence of residual polyphenols in the extract and raise the question of the role of these compounds in the interfacial properties of plant protein extracts.

Temperature-sensitive soft microgels at interfaces: air-water versus oil-water

The formation of smart emulsions or foams whose stability can be controlled on-demand by switching external parameters is of great interest for basic research and applications. An emerging group of smart stabilizers are microgels, which are nano- and micro-sized, three-dimensional polymer networks that are swollen by a good solvent. In the last decades, the influence of various external stimuli on the two-dimensional phase behavior of microgels at air- and oil-water interfaces has been studied. However, the impact of the top-phase itself has been barely considered. Here, we present data that directly address the influence of the top-phase on the microgel properties at interfaces. The dimensions of pNIPAM microgels are measured after deposition from two interfaces, i.e., air- and decane-water. While the total in-plane size of the microgel increases with increasing interfacial tension, the portions or fractions of the microgels situated in the aqueous phase are not affected. We correlate the area microgels occupy to the surface tensions of the interfaces, which allows to estimate an elastic modulus. In comparison to nanoindentation measurements, we observe a larger elastic modulus for the microgels. By combining compression, deposition, and visualization, we show that the two-dimensional phase behavior of the microgel monolayers is not altered, although the microgels have a larger total in-plane size at higher interfacial tension.

Near-zero surface pressure assembly of rectangular lattices of microgels at fluid interfaces for colloidal lithography

Understanding and engineering the self-assembly of soft colloidal particles (microgels) at liquid-liquid interfaces is broadening their use in colloidal lithography. Here, we present a new route to assemble rectangular lattices of microgels at near zero surface pressure relying on the balance between attractive quadrupolar capillary interactions and steric repulsion among the particles at water/oil interfaces. These self-assembled rectangular lattices are obtained for a broad range of particles and, after deposition, can be used as lithography masks to obtain regular arrays of vertically aligned nanowires via wet and dry etching processes.

Static interface profiles for contact lines on an elastic membrane with the Willmore energy

We consider a fluid interface in contact with an elastic membrane and study the static profiles of the interface and the membrane. Equilibrium conditions are derived by minimizing the total energy of the system with volume constraints. The total energy consists of surface energies and the Willmore energy; the latter penalizes the bending of the membrane. It is found that, while the membrane is locally flat at the contact line with the contact angle satisfying the Young-Dupré equation, the gradient of the mean curvature of the membrane exhibits a jump across the contact line. This jump balances the surface tension of the fluid interface in the normal direction of the membrane. Asymptotic solutions are obtained for two-dimensional systems in the limits as the reduced bending modulus ν tends to +∞ and 0, respectively. In the stiff limit as ν→+∞, the leading-order solution is given by that of a droplet sitting on a rigid substrate with the contact angle satisfying the Young-Dupré equation; in contrast, in the soft limit as ν→0, a transition layer appears near the contact line and the interfaces have constant curvatures in the outer region with apparent contact angles obeying Neumann's law. These solutions are validated by numerical experiments.

Microgels self-assembly at liquid/liquid interface as stabilizers of emulsion: Past, present & future

The most recent developments on Pickering emulsions deal with the design of responsive emulsions able to undergo fast destabilization under the effect of an external stimulus. In this scenario, soft colloidal particles like microgels are considered novel class suitable emulsifiers. Microgels particles self-assemblies are highly deformable at interfaces covering higher surfaces than hard particles and their interfacial behavior strongly depends on external-stimuli. Microgels are very diverse owing to the large variety of them from the point of view of possible combinations of stimuli-responsiveness and different microstructures (crosslinking density and distribution). Herein, we illustrate the use of different types of responsive microgels not only from a structural point of view but also even from physical one. For that, the effect of different microgels parameters such as internal structure and charge density on mechanical properties of the interface will be discussed.

Catalysis in Pickering emulsions

Particle-stabilised or Pickering emulsions are versatile systems. In the past 10 years a new application has emerged in the field of catalysis to use them as vehicles to carry out catalytic reactions, allowing a more environmentally friendly process with high conversions and selectivities and important advantages for catalyst recovery. As the area has advanced rapidly, the intention of this review is to summarize the latest innovations being reported. An overview is given regarding the kinds of liquid phases comprising the emulsion system, the different types of solid particle stabilizers (whether they contain catalyst or not) and the catalytic reactions studied. A section describing methods for recovering the catalyst is also included, in which various stimuli are discussed. Finally, the importance of using Pickering emulsions to carry out reactions in flow and in multi-step cascade systems is highlighted with various examples to support the benefits of transferring this technology to industrial processes.

Interfacial viscoelasticity and jamming of colloidal particles at fluid-fluid interfaces: a review

Colloidal particles can be adsorbed at fluid-fluid interfaces, a phenomenon frequently observed in particle-stabilized foams, Pickering emulsions, and bijels. Particles adsorbed at interfaces exhibit unique physical and chemical behaviors, which affect the mechanical properties of the interface. Therefore, interfacial colloidal particles are of interest in terms of both fundamental and applied research. In this paper, we review studies on the adsorption of colloidal particles at fluid-fluid interfaces, from both thermodynamic and mechanical points of view, and discuss the differences as compared with surfactants and polymers. The unique particle interactions induced by the interfaces as well as the particle dynamics including lateral diffusion and contact line relaxation will be presented. We focus on the rearrangement of the particles and the resultant interfacial viscoelasticity. Particular emphasis will be given to the effects of particle shape, size, and surface hydrophobicity on the interfacial particle assembly and the mechanical properties of the obtained particle layer. We will also summarize recent advances in interfacial jamming behavior caused by adsorption of particles at interfaces. The buckling and cracking behavior of particle layers will be discussed from a mechanical perspective. Finally, we suggest several potential directions for future research in this area.