Nanoplasmonic sensors for biointerfacial science

Determination of the Localized Surface Plasmon Resonance Alteration of AgNPs via Multiwavelength Evanescent Scattering Microscopy for Pb(II) Detection

We developed multiwavelength evanescent scattering microscopy (MWESM), which can acquire plasmonic nanoparticle images at the particle level using the evanescent field as the incident source and distinguish different LSPR (localized surface plasmon resonance) spectral peaks among four wavelengths. Our microscope could be easily and simply built by modifying a commercial total internal reflection fluorescence microscope (TIRFM) with the substitution of a beamsplitter and the addition of a semicircular stop. The ultrathin depth of illumination and rejection of the reflected incident source together contribute to the high sensitivity and contrast of single nanoparticle imaging. We first validated the capability of our imaging system in distinguishing plasmonic nanoparticles bearing different LSPR spectral peaks, and the results were consistent with the scattering spectra results of hyperspectral imaging. Moreover, we demonstrated high imaging quality from the aspects of the signal/noise ratio and point spread function of the single-particle images. Meaningfully, the system can be utilized in rapidly determining the concentration of toxic lead ions in environmental and biological samples with good linearity and sensitivity, based on single-particle evanescent scattering imaging through the detection of the alteration of the LSPR of silver nanoparticles. This system holds the potential to advance the field of nanoparticle imaging and foster the application of nanomaterials as sensors.

Fragment-based approach to study fungicide-biomimetic membrane interactions

In this study, the molecular interactions of the allylamine-type fungicide butenafine and a set of substructures ("fragments") with liposomes mimicking biological membranes were studied to gain a better understanding of the structural factors governing membrane affinity and perturbation. Specifically, drug/fragment-membrane interactions were investigated using an interdisciplinary approach involving micro differential scanning calorimetry, open-tubular capillary electrochromatography, nanoplasmonic sensing, and quartz crystal microbalance. By incubating the drug and the fragment compounds with liposomes with varying lipid composition or by externally adding the compounds to preformed liposomes, a detailed mechanistic picture on the underlying drug/fragment-membrane interactions was obtained. The nature and the degree of ionisation of polar head groups of the lipids had a major influence on the nature of drug-membrane interactions, and so had the presence and relative concentration of cholesterol within the membranes. The in-depth understanding of drug/fragment-membranes interactions established by the presented interdisciplinary fragment-based approach may be useful in guiding the design and early-stage evaluation of prospective antifungal drug candidates, and the discovery of agents with improved membrane penetrating characteristics in general.

Advances in Nanoplasmonic Biosensors: Optimizing Performance for Exosome Detection Applications

The development of sensitive and specific exosome detection tools is essential because they are believed to provide specific information that is important for early detection, screening, diagnosis, and monitoring of cancer. Among the many detection tools, surface-plasmon resonance (SPR) biosensors are analytical devices that offer advantages in sensitivity and detection speed, thereby making the sample-analysis process faster and more accurate. In addition, the penetration depth of the SPR biosensor, which is <300 nm, is comparable to the size of the exosome, making the SPR biosensor ideal for use in exosome research. On the other hand, another type of nanoplasmonic sensor, namely a localized surface-plasmon resonance (LSPR) biosensor, has a shorter penetration depth of around 6 nm. Structural optimization through the addition of supporting layers and gap control between particles is needed to strengthen the surface-plasmon field. This paper summarizes the progress of the development of SPR and LSPR biosensors for detecting exosomes. Techniques in signal amplification from two sensors will be discussed. There are three main parts to this paper. The first two parts will focus on reviewing the working principles of each sensor and introducing several methods that can be used to isolate exosomes. This article will close by explaining the various sensor systems that have been developed and the optimizations carried out to obtain sensors with better performance. To illustrate the performance improvements in each sensor system discussed, the parameters highlighted include the detection limit, dynamic range, and sensitivity.

Raman Monitoring of the Electro-Optical Synergy-Induced Enhancements in Carbon-Bromine Bond Cleavage, Reaction Rate, and Product Selectivity of p-Bromothiophenol

Electro-optical synergy has recently been targeted to improve the separation of hot carriers and thereby further improve the efficiency of plasmon-mediated chemical reactions (PMCRs). However, the electro-optical synergy in PMCRs needs to be more deeply understood, and its contribution to bond dissociation and product selectivity needs to be clarified. Herein, the electro-optical synergy in plasmon-mediated reduction of p-bromothiophenol (PBTP) was studied on a plasmonic nanostructured silver electrode using in situ Raman spectroscopy and theoretical calculations. It was found that the electro-optical synergy-induced enhancements in the cleavage of carbon-bromine bonds, reaction rate, and product selectivity (4,4'-biphenyl dithiol vs thiophenol) were largely affected by the applied bias, laser wavelength, and laser power. The theoretical simulation further clarified that the strong electro-optical synergy is attributed to the matching of energy band diagrams of the plasmonic silver with those of the adsorbed PBTP molecules. A deep understanding of the electro-optical synergy in PBTP reduction and the clarification of the mechanism will be highly beneficial for the development of other highly efficient PMCRs.

Combined Photothermal Therapy and Cancer Immunotherapy by Immunogenic Hollow Mesoporous Silicon-Shelled Gold Nanorods

Hyperthermia can be integrated with tumor-killing chemotherapy, radiotherapy and immunotherapy to give rise to an anti-tumor response. To this end, a nano-delivery system is built, which can connect hyperthermia and immunotherapy. On this basis, the impact of such a combination on the immune function of dendritic cells (DCs) is explored. The core of this system is the photothermal material gold nanorod (GNR), and its surface is covered with a silica shell. Additionally, it also forms a hollow mesoporous structure using the thermal etching approach, followed by modification of targeted molecule folic acid (FA) on its surface, and eventually forms a hollow mesoporous silica gold nanorod (GNR@void@mSiO2) modified by FA. GNR@void@mSiO2-PEG-FA (GVS-FA) performs well in photothermal properties, drug carriage and release and tumor targeting performance. Furthermore, the thermotherapy of tumor cells through in vitro NIR irradiation can directly kill tumor cells by inhibiting proliferation and inducing apoptosis. GVS-FA loaded with imiquimod (R837) can be used as a adjuvant to enhance the immune function of DCs through hyperthermia.

A Synergistic View on Osmolyte's Role against Salt and Cold Stress in Biointerfaces

We present our perspective on the role of osmolytes in mitigating abiotic stresses such as hypersalinity and sudden temperature changes. While the stabilizing effect of osmolytes on protein tertiary structures has been extensively studied, their direct impact on abiotic stress factors has eluded mainstream attention. Via highlighting a set of recent success stories of a joint venture of computer simulations and experimental measurements, we summarize the mechanistic insights into osmolytic action, particularly in the context of salt stress and combined cold-salt stress at the interface of biomolecular surfaces and saline environments. We stress the importance of chemical specificity in osmolytic activity, the interplay of differential osmolytic behaviors against heterogeneous salt stress, and the capability of osmolytes to adopt combined actions. Additionally, we discuss the potential of incorporating nanomaterial-based systems to enrich our understanding of osmolyte bioactions and facilitate their practical applications. We anticipate that this discourse will inspire interdisciplinary collaborations and motivate further investigations on osmolytes, ultimately broadening their applications in the fields of health and disease.

Optoplasmonic Effects in Highly Curved Surfaces for Catalysis, Photothermal Heating, and SERS

Surface curvature can be used to focus light and alter optical processes. Here, we show that curved surfaces (spheres, cylinders, and cones) with a radius of around 5 μm lead to maximal optoplasmonic properties including surface-enhanced Raman scattering (SERS), photocatalysis, and photothermal processes. Glass microspheres, microfibers, pulled fibers, and control flat substrates were functionalized with well-dispersed and dense arrays of 45 nm Au NP using polystyrene-block-poly-4-vinylpyridine (PS-b-P4VP) and chemically modified with 4-mercaptobenzoic acid (4-MBA, SERS reporter), 4-nitrobenzenethiol (4-NBT, reactive to plasmonic catalysis), or 4-fluorophenyl isocyanide (FPIC, photothermal reporter). The various curved substrates enhanced the plasmonic properties by focusing the light in a photonic nanojet and providing a directional antenna to increase the collection efficacy of SERS photons. The optoplasmonic effects led to an increase of up to 1 order of magnitude of the SERS response, up to 5 times the photocatalytic conversion of 4-NBT to 4,4'-dimercaptoazobenzene when the diameter of the curved surfaces was about 5 μm and a small increase in photothermal effects. Taken together, the results provide evidence that curvature enhances plasmonic properties and that its effect is maximal for spherical objects around a few micrometers in diameter, in agreement with a theoretical framework based on geometrical optics. These enhanced plasmonic effects and the stationary-phase-like plasmonic substrates pave the way to the next generation of sensors, plasmonic photocatalysts, and photothermal devices.

Investigation of the Optical Nonlinearity for Au Plasmonic Nanoparticles Based on Ion Implantation

The Au ion implantation process has emerged as an effective and simple method to be utilized for the fabrication of opto-electronic materials and devices due to numerous fascinating features of Au nanoparticles such as surface plasmon resonance (SPR), large third-order nonlinearity and a fast response time. In this paper, we describe the fabrication of a novel Au nanoparticle saturable absorber (Au NP-SA) by embedding the Au NPs into a SiO2 thin film using the ion implantation process, which shows excellent saturable absorption features due to the localized surface plasmon resonance (LSPR) effect of Au NPs. A stable and high-quality pulsed laser with a repetition rate of 33.3 kHz and a single pulse energy of 11.7 nJ was successfully constructed with the Au NP-SA. Both the stable operation characteristic of the obtained Q-switched pulsed laser and the high repeatability of the fabrication process of the Au NP-SA were demonstrated. In addition, the simple feasibility and maturity of the ion implantation process allow for the plasmonic nanoparticles to be easily integrated into other types of opto-electronic materials and devices to further improve their performance, and shows immense potential for the production of wafer-level products.

Effect of liposome composition on β-blocker interactions studied by capillary electrokinetic chromatography

Liposome capillary electrokinetic chromatography was used to investigate the interactions between three β-blockers of different hydrophobicity and various liposome solutions. The studied β-blockers comprised alprenolol, propranolol, and carvedilol. The composition of the liposome solutions, containing 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine, 1,2-dioleoyl-sn-glycero-3-phos-phoethanolamine, 1-palmitoyl-2-oleoyl-sn-glycero-3-phospho-l-serine, and cholesterol in various molar ratios, was designed by a response surface methodology-central composite design approach. Subsequently, after conducting the liposome capillary electrokinetic chromatography experiments and determining the retention factors from the electrophoretic mobilities of the compounds, and further calculating the distribution coefficients, an analysis of variance was performed. After extracting the statistical models, optimal operational conditions were obtained based on the developed models. To further investigate the interactions between the β-blockers and the liposomes, nanoplasmonic sensing experiments were carried out on two different liposome systems. The overall results demonstrate the strong influence of cholesterol and 1-palmitoyl-2-oleoyl-sn-glycero-3-phospho-l-serine on the distribution coefficients.

Developing an Electrochemically Reversible Switch for Modulating the Optical Signal of Gold Nanoparticles

Gold nanoparticles (AuNPs) possess remarkable optical properties and electrical conductivity, making them highly relevant in various fields such as medical diagnoses, biological imaging, and electronic sensors. However, the existing methods for modulating the optical properties of AuNPs are often under limitations such as a high cost, the complexity of detection, a narrow range of application settings, and irreversibility. In this study, we propose a novel approach to address these challenges by constructing a reversible electrochemical switch. The switch (ITO-OMAD) involves covalently linking nitroxide radicals and AuNPs (AuNPs-NO•), followed by tethering this nanocomposite to a siloxane-derived indium tin oxide (ITO) electrode. By simply electrochemically oxidizing/reducing the nitroxide units, one is able to reversibly modulate the optical properties of AuNPs at will. The surface morphology and structure of the as-prepared ITO-OMAD electrode were characterized through scanning electron microscopy (SEM) and cyclic voltammetry (CV). SEM imaging confirmed the successful anchoring of AuNPs on the ITO electrode. Electrochemical tests performed in the three-electrode system demonstrated that the local surface plasmon resonance (LSPR) of AuNPs can be reversibly regulated by alternatively imposing ± 0.5V (vs. Ag/AgCl) to the modified electrode. The development of this electrochemical switch presents a novel approach to effectively control the optical properties of AuNPs. The further exploration and utilization of this reversible electrochemical switch could significantly enhance the versatility and practicality of AuNPs in numerous applications.

Small-molecule probes from bench to bedside: advancing molecular analysis of drug-target interactions toward precision medicine

Over the past decade, remarkable advances have been witnessed in the development of small-molecule probes. These molecular tools have been widely applied for interrogating proteins, pathways and drug-target interactions in preclinical research. While novel structures and designs are commonly explored in probe development, the clinical translation of small-molecule probes remains limited, primarily due to safety and regulatory considerations. Recent synergistic developments - interfacing novel chemical probes with complementary analytical technologies - have introduced and expedited diverse biomedical opportunities to molecularly characterize targeted drug interactions directly in the human body or through accessible clinical specimens (e.g., blood and ascites fluid). These integrated developments thus offer unprecedented opportunities for drug development, disease diagnostics and treatment monitoring. In this review, we discuss recent advances in the structure and design of small-molecule probes with novel functionalities and the integrated development with imaging, proteomics and other emerging technologies. We further highlight recent applications of integrated small-molecule technologies for the molecular analysis of drug-target interactions, including translational applications and emerging opportunities for whole-body imaging, tissue-based measurement and blood-based analysis.

Comparative effects of hepatocyte growth factor and tacrolimus on acute liver allograft early tolerance

Allostimulated CD8+ T cells (aCD8+ T cells), as the main mediators of acute liver rejection (ARJ), are hyposensitive to apoptosis due to the inactivation of death receptor FAS-mediated pathways and fail to allow tolerance induction, eventually leading to acute graft rejection. Although tacrolimus (FK506), the most commonly used immunosuppressant (IS) in the clinic, allows tolerance induction, its use is limited because its target immune cells are unknown and it is associated with increased incidences of malignancy, infection, and nephrotoxicity, which substantially impact long-term liver transplantation (LTx) outcomes. The dark agouti (DA)-to-Lewis rat LTx model is a well-known ARJ model and was hence chosen for the present study. We show that both hepatocyte growth factor (HGF) (cHGF, containing the main form of promoting HGF production) and recombinant HGF (h-rHGF) exert immunoregulatory effects mainly on allogeneic aCD8+ T cell suppression through FAS-mediated apoptotic pathways by inhibiting cMet to FAS antagonism and Fas trimerization, leading to acute tolerance induction. We also showed that such inhibition can be abrogated by treatment with neutralizing antibodies against cMet (HGF-only receptor). In contrast, we did not observe these effects in rats treated with FK506. However, we observed that the effect of anti-rejection by FK506 was mainly on allostimulated CD4+ T cell (aCD4+ T cell) suppression and regulatory T cell (Treg) promotion, in contrast to the mechanism of HGF. In addition, the protective mechanism of HGF in FK506-mediated nephrotoxicity was addressed. Therefore, HGF as a tolerance inducer, whether used in combination with FK506 or as monotherapy, may have good clinical value. Additional roles of these T-cell subpopulations in other biological systems and studies in these fields will also be meaningful.

Effect of nanoshell geometries, sizes, and quantum emitter parameters on the sensitivity of plasmon-exciton hybrid nanoshells for sensing application

A proposed nanosensor based on hybrid nanoshells consisting of a core of metal nanoparticles and a coating of molecules is simulated by plasmon-exciton coupling in semi classical approach. We study the interaction of electromagnetic radiation with multilevel atoms in a way that takes into account both the spatial and the temporal dependence of the local fields. Our approach has a wide range of applications, from the description of pulse propagation in two-level media to the elaborate simulation of optoelectronic devices, including sensors. We have numerically solved the corresponding system of coupled Maxwell-Liouville equations using finite difference time domain (FDTD) method for different geometries. Plasmon-exciton hybrid nanoshells with different geometries are designed and simulated, which shows more sensitive to environment refractive index (RI) than nanosensor based on localized surface plasmon. The effects of nanoshell geometries, sizes, and quantum emitter parameters on the sensitivity of nanosensors to changes in the RI of the environment were investigated. It was found that the cone-like nanoshell with a silver core and quantum emitter shell had the highest sensitivity. The tapered shape of the cone like nanoshell leads to a higher density of plasmonic excitations at the tapered end of the nanoshell. Under specific conditions, two sharp, deep LSPR peaks were evident in the scattering data. These distinguishing features are valuable as signatures in nanosensors requiring fast, noninvasive response.

Dielectrophoretic trapping of nanosized biomolecules on plasmonic nanohole arrays for biosensor applications: simple fabrication and visible-region detection

Surface plasmon resonance is an optical phenomenon that can be applied for label-free, real-time sensing to directly measure biomolecular interactions and detect biomarkers in solutions. Previous studies using plasmonic nanohole arrays have monitored and detected various biomolecules owing to the propagating surface plasmon polaritons (SPPs). Extraordinary optical transmission (EOT) that occurs in the near-infrared (NIR) and infrared (IR) regions is usually used for detection. Although these plasmonic nanohole arrays improve the sensitivity and throughput for biomolecular detection, these arrays have the following disadvantages: (1) molecular diffusion in the solution (making the detection of biomolecules difficult), (2) the device fabrication's complexities, and (3) expensive equipments for detection in the NIR or IR regions. Therefore, there is a need to fabricate plasmonic nanohole arrays as biomolecular detection platforms using a simple and highly reproducible procedure based on other SPP modes in the visible region instead of the EOT in the NIR or IR regions while suppressing molecular diffusion in the solution. In this paper, we propose the combination of a polymer-based gold nanohole array (Au NHA) obtained through an easy process as a simple platform and dielectrophoresis (DEP) as a biomolecule manipulation method. This approach was experimentally demonstrated using SPP and LSPR modes (not EOT) in the visible region and simple, label-free, rapid, cost-effective trapping and enrichment of nanoparticles (trapping time: <50 s) and bovine serum albumin (trapping time: <1000 s) was realized. These results prove that the Au NHA-based DEP devices have great potential for real-time digital and Raman bioimaging, in addition to biomarker detection.

Nanoplasmonic biosensors for precision medicine

Nanoplasmonic biosensors have a huge boost for precision medicine, which allows doctors to better understand diseases at the molecular level and to improve the earlier diagnosis and develop treatment programs. Unlike traditional biosensors, nanoplasmonic biosensors meet the global health industry's need for low-cost, rapid and portable aspects, while offering multiplexing, high sensitivity and real-time detection. In this review, we describe the common detection schemes used based on localized plasmon resonance (LSPR) and highlight three sensing classes based on LSPR. Then, we present the recent applications of nanoplasmonic in other sensing methods such as isothermal amplification, CRISPR/Cas systems, lab on a chip and enzyme-linked immunosorbent assay. The advantages of nanoplasmonic-based integrated sensing for multiple methods are discussed. Finally, we review the current applications of nanoplasmonic biosensors in precision medicine, such as DNA mutation, vaccine evaluation and drug delivery. The obstacles faced by nanoplasmonic biosensors and the current countermeasures are discussed.

Review of nanomaterial advances for ionizing radiation dosimetry

There are a wide range of applications with ionizing radiation and a common theme throughout these is that accurate dosimetry is usually required, although many newer demands are provided by improved features in higher range, multi-spectral and particle type detected. Today, the array of dosimeters includes both offline and online tools, such as gel dosimeters, thermoluminescence (TL), scintillators, optically stimulated luminescence (OSL), radiochromic polymeric films, gels, ionization chambers, colorimetry, and electron spin resonance (ESR) measurement systems. Several future nanocomposite features and interpretation of their substantial behaviors are discussed that can lead to improvements in specific features, such as (1) lower sensitivity range, (2) less saturation at high range, (3) overall increased dynamic range, (4) superior linearity, (5) linear energy transfer and energy independence, (6) lower cost, (7) higher ease of use, and (8) improved tissue equivalence. Nanophase versions of TL and ESR dosimeters and scintillators each have potential for higher range of linearity, sometimes due to superior charge transfer to the trapping center. Both OSL and ESR detection of nanomaterials can have increased dose sensitivity because of their higher readout sensitivity with nanoscale sensing. New nanocrystalline scintillators, such as perovskite, have fundamentally important advantages in sensitivity and purposeful design for key new applications. Nanoparticle plasmon coupled sensors doped within a lower Zeff material have been an effective way to achieve enhanced sensitivity of many dosimetry systems while still achieving tissue equivalency. These nanomaterial processing techniques and unique combinations of them are key steps that lead to the advanced features. Each must be realized through industrial production and quality control with packaging into dosimetry systems that maximize stability and reproducibility. Ultimately, recommendations for future work in this field of radiation dosimetry were summarized throughout the review.

Nanoparticle-Enhanced RT-QuIC (Nano-QuIC) Diagnostic Assay for Misfolded Proteins

Misfolded proteins associated with various neurodegenerative diseases often accumulate in tissues or circulate in biological fluids years before the clinical onset, thus representing ideal diagnostic targets. Real-time quaking-induced conversion (RT-QuIC), a protein-based seeded-amplification assay, holds great potential for early disease detection, yet challenges remain for routine diagnostic application. Chronic Wasting Disease (CWD), associated with misfolded prion proteins of cervids, serves as an ideal model for evaluating new RT-QuIC methodologies. In this study, we investigate the previously untested hypothesis that incorporating nanoparticles into RT-QuIC assays can enhance their speed and sensitivity when applied to biological samples. We show that adding 50 nm silica nanoparticles to RT-QuIC experiments (termed Nano-QuIC) for CWD diagnostics greatly improves the performance by reducing detection times 2.5-fold and increasing sensitivity 10-fold by overcoming the effect of inhibitors in complex tissue samples. Crucially, no false positives were observed with these 50 nm silica nanoparticles, demonstrating the enhanced reliability and potential for diagnostic application of Nano-QuIC in detecting misfolded proteins.

Fiber Optic Localized Surface Plasmon Resonance Sensor Based on Carboxymethylated Dextran Modified Gold Nanoparticles Surface for High Mobility Group Box 1 (HMGB1) Analysis

Rapid, sensitive, and reliable detection of high mobility group box 1 (HMGB1) is essential for medical and diagnostic applications due to its important role as a biomarker of chronic inflammation. Here, we report a facile method for the detection of HMGB1 using carboxymethyl dextran (CM-dextran) as a bridge molecule modified on the surface of gold nanoparticles combined with a fiber optic localized surface plasmon resonance (FOLSPR) biosensor. Under optimal conditions, the results showed that the FOLSPR sensor detected HMGB1 with a wide linear range (10^-10 to 10^-6 g/mL), fast response (less than 10 min), and a low detection limit of 43.4 pg/mL (1.7 pM) and high correlation coefficient values (>0.9928). Furthermore, the accurate quantification and reliable validation of kinetic binding events measured by the currently working biosensors are comparable to surface plasmon resonance sensing systems, providing new insights into direct biomarker detection for clinical applications.

High-throughput spatiotemporal monitoring of single-cell secretions via plasmonic microwell arrays

Methods for the analysis of cell secretions at the single-cell level only provide semiquantitative endpoint readouts. Here we describe a microwell array for the real-time spatiotemporal monitoring of extracellular secretions from hundreds of single cells in parallel. The microwell array incorporates a gold substrate with arrays of nanometric holes functionalized with receptors for a specific analyte, and is illuminated with light spectrally overlapping with the device's spectrum of extraordinary optical transmission. Spectral shifts in surface plasmon resonance resulting from analyte-receptor bindings around a secreting cell are recorded by a camera as variations in the intensity of the transmitted light while machine-learning-assisted cell tracking eliminates the influence of cell movements. We used the microwell array to characterize the antibody-secretion profiles of hybridoma cells and of a rare subset of antibody-secreting cells sorted from human donor peripheral blood mononuclear cells. High-throughput measurements of spatiotemporal secretory profiles at the single-cell level will aid the study of the physiological mechanisms governing protein secretion.

Affinity Exploration of SARS-CoV-2 RBD Variants to mAb-Functionalized Plasmonic Metasurfaces for Label-Free Immunoassay Boosting

Plasmonic metasurfaces (PMs) functionalized with the monoclonal antibody (mAb) are promising biophotonic sensors for biomolecular interaction analysis and convenient immunoassay of various biomarkers, such as severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) variants. Previous PM biosensing suffers from the slow affinity detection rate and lack of sufficient immunoassay studies on various SARS-CoV-2 variants. Here, we develop a high-efficiency affinity testing method based on label-free PM sensors with mAbs and demonstrate their binding characteristics to 12 spike receptor binding domain (RBD) variants of SARS-CoV-2. In addition to the research of plasmonic near-field influence on surface biomolecule sensing, we provide a comprehensive report about the Langmuir binding equilibrium of molecular kinetics between 12 SARS-CoV-2 RBD variants and mAb-functionalized PMs, which plays a crucial role in label-free immunosensing. A high-affinity mAb can be combined with the highly sensitive propagating plasmonic mode to boost the detection of SARS-CoV-2 variants. Owing to a better understanding of molecular dynamics on PMs, we develop an ultrasensitive biosensor of the SARS-CoV-2 Omicron variant. The experiments show great distinguishment of P < 0.0001 from respiratory diseases induced by other viruses, and the limit of detection is 2 orders smaller than the commercial colloidal gold immunoassay. Our study shows the label-free biosensing by low-cost wafer-scale PMs, which will provide essential information on biomolecular interaction and facilitate high-precision point-of-care testing for emerging SARS-CoV-2 variants in the future.

Investigating the Sequence Specific Adsorption Behavior of Polypeptides at the Solid/Liquid Interface

Polymer adsorption at the solid/liquid interface depends not only on the chemical composition of the polymer but also on the specific placement of the monomers along the polymer sequence. However, challenges in designing polymers with well-controlled sequences have limited explorations into the role of polymer sequence on adsorption behavior to molecular simulations. Here, we demonstrate how the sequence control offered by polypeptide synthesis can be utilized to study the effects small changes in polymer sequence have on polymer adsorption behavior at the solid/liquid interface. Through a combination of quartz crystal microbalance with dissipation monitoring and total internal reflection ellipsometry, we study the adsorption behavior of three polypeptides, consisting of 90% lysine and 10% cysteine, onto a gold surface. We find different mechanisms are responsible for the adsorption of polypeptides and the resulting conformation on the surface. The initial adsorption of the polypeptides is driven by electrostatic interactions between the polylysine and the gold surface. Once adsorbed, the cysteine undergoes a thiol-Au reaction with the surface, altering the conformation of the polymer layer. Our findings suggest the conformation of the polypeptide layer is dependent on the placement of the cysteines within the sequence; polypeptide chains with evenly spaced cysteine groups adopt a more tightly bound "train" conformation as compared to polypeptides with closely grouped cysteine groups. We envision that the methodologies presented here to study sequence specific adsorption behaviors using polypeptides could be a valuable tool to complement molecular simulations studies.

Time-Resolved Thickness and Shape-Change Quantification using a Dual-Band Nanoplasmonic Ruler with Sub-Nanometer Resolution

Time-resolved measurements of changes in the size and shape of nanobiological objects and layers are crucial to understand their properties and optimize their performance. Optical sensing is particularly attractive with high throughput and sensitivity, and label-free operation. However, most state-of-the-art solutions require intricate modeling or multiparameter measurements to disentangle conformational or thickness changes of biomolecular layers from complex interfacial refractive index variations. Here, we present a dual-band nanoplasmonic ruler comprising mixed arrays of plasmonic nanoparticles with spectrally separated resonance peaks. As electrodynamic simulations and model experiments show, the ruler enables real-time simultaneous measurements of thickness and refractive index variations in uniform and heterogeneous layers with sub-nanometer resolution. Additionally, nanostructure shape changes can be tracked, as demonstrated by quantifying the degree of lipid vesicle deformation at the critical coverage prior to rupture and supported lipid bilayer formation. In a broader context, the presented nanofabrication approach constitutes a generic route for multimodal nanoplasmonic optical sensing.

Optimizing Plasmonic Gold Nanorod Deposition on Glass Surfaces for High-Sensitivity Refractometric Biosensing

Owing to high surface sensitivity, gold nanorods (AuNRs) are widely used to construct surface-based nanoplasmonic biosensing platforms for label-free molecular diagnostic applications. A key fabrication step involves controlling AuNR deposition onto the target surface, which requires maximizing surface density while minimizing inter-particle aggregation, and is often achieved by surface functionalization with a self-assembled monolayer (SAM) prior to AuNR deposition. To date, existing studies have typically used a fixed concentration of SAM-forming organic molecules (0.2-10% v/v) while understanding how SAM density affects AuNR deposition and resulting sensing performance would be advantageous. Herein, we systematically investigated how controlling the (3-aminopropyl)triethoxysilane (APTES) concentration (1-30% v/v) during SAM preparation affects the fabrication of AuNR-coated glass surfaces for nanoplasmonic biosensing applications. Using scanning electron microscopy (SEM) and UV-visible spectroscopy, we identified an intermediate APTES concentration range that yielded the highest density of individually deposited AuNRs with minimal aggregation and also the highest peak wavelength in aqueous solution. Bulk refractive index sensitivity measurements indicated that the AuNR configuration had a strong effect on the sensing performance, and the corresponding wavelength-shift responses ranged from 125 to 290 nm per refractive index unit (RIU) depending on the APTES concentration used. Biosensing experiments involving protein detection and antigen-antibody interactions further demonstrated the high surface sensitivity of the optimized AuNR platform, especially in the low protein concentration range where the measurement shift was ~8-fold higher than that obtained with previously used sensing platforms.

Single-Particle Measurements of Nanocatalysis with Dark-Field Microscopy

Due to the complexity of heterogeneous reactions and heterogeneities of individual catalyst particles in size, morphology, and the surrounding medium, it is very important to characterize the structure of nanocatalysts and measure the reaction process of nanocatalysis at the single-particle level. Traditional ensemble measurements, however, only provide averaged results of billions of nanoparticles (NPs), which do not help reveal structure–activity relationships and may overlook a few NPs with high activity. The advent of dark-field microscopy (DFM) combined with plasmonic resonance Rayleigh scattering (PRRS) spectroscopy provides a powerful means for directly recording the localized surface plasmon resonance (LSPR) spectrum of single plasmonic nanoparticles (PNPs), which also enables quantitative measurements. In recent years, DFM has developed rapidly for a series of single-particle catalytic reactions such as redox reactions, electrocatalytic reactions, and DNAzyme catalysis, with the ability to monitor the catalytic reaction process in real time and reveal the catalytic mechanism. This review provides a comprehensive overview of the fundamental principles and practical applications of DFM in measuring various kinds of catalysis (including chemocatalysis, electrocatalysis, photocatalysis, and biocatalysis) at the single-particle level. Perspectives on the remaining challenges and future trends in this field are also proposed.

Determination of the Highly Sensitive Carboxyl-Graphene Oxide-Based Planar Optical Waveguide Localized Surface Plasmon Resonance Biosensor

This study develops a highly sensitive and low-cost carboxyl-graphene-oxide-based planar optical waveguide localized surface plasmon resonance biosensor (GO-OW LSPR biosensor), a system based on measuring light intensity changes. The structure of the sensing chip comprises an optical waveguide (OW)-slide glass and microfluidic-poly (methyl methacrylate) (PMMA) substrate, and the OW-slide glass surface-modified gold nanoparticle (AuNP) combined with graphene oxide (GO). As the GO has an abundant carboxyl group (–COOH), the number of capture molecules can be increased. The refractive index sensing system uses silver-coated reflective film to compare the refractive index sensitivity of the GO-OW LSPR biosensor to increase the refractive index sensitivity. The result shows that the signal variation of the system with the silver-coated reflective film is 1.57 times that of the system without the silver-coated reflective film. The refractive index sensitivity is 5.48 RIU⁻¹ and the sensor resolution is 2.52 ± 0.23 × 10⁻⁶ RIU. The biochemical sensing experiment performs immunoglobulin G (IgG) and streptavidin detection. The limits of detection of the sensor for IgG and streptavidin are calculated to be 23.41 ± 1.54 pg/mL and 5.18 ± 0.50 pg/mL, respectively. The coefficient of variation (CV) of the repeatability experiment (sample numbers = 3) is smaller than 10.6%. In addition, the affinity constants of the sensor for anti-IgG/IgG and biotin/streptavidin are estimated to be 1.06 × 10⁷ M⁻¹ and 7.30 × 10⁹ M⁻¹, respectively. The result shows that the GO-OW LSPR biosensor has good repeatability and very low detection sensitivity. It can be used for detecting low concentrations or small biomolecules in the future.

Interactions of proteins with metal-based nanoparticles from a point of view of analytical chemistry - Challenges and opportunities

Interactions of proteins with nanomaterials draw attention of many research groups interested in fundamental phenomena. However, alongside with valuable information regarding physicochemical aspects of such processes and their mechanisms, they more and more often prove to be useful from a point of view of bioanalytics. Deliberate use of processes based on adsorption of proteins on nanoparticles (or vice versa) allows for a development of new analytical methods and improvement of the existing ones. It also leads to obtaining of nanoparticles of desired properties and functionalities, which can be used as elements of analytical tools for various applications. Due to interactions with nanoparticles, proteins can also gain new functionalities or lose their interfering potential, which from perspective of bioanalytics seems to be very inviting and attractive. In the framework of this article we will discuss the bioanalytical potential of interactions of proteins with a chosen group of nanoparticles, and implementation of so driven processes for biosensing. Moreover, we will show both positive and negative (opportunities and challenges) aspects resulting from the presence of proteins in media/samples containing metal-based nanoparticles or their precursors.

Bio-electron transfer modulated localized surface plasmon resonance biosensing with charge density monitoring

The analysis of reactant at different regions of the bioreaction interface is significant for the study on the influence of interface condition on bioreaction. In this study, we proposed a localized surface plasmon resonance (LSPR) biosensing platform for local charge density monitoring and corresponding analytes detection based on the bio-electron transfer modulation of plasmon resonance. Core-shell nanocomposites of polyaniline coated gold nanoparticles were synthesized for the enhanced sensitivity of plasmon resonance to applied electric potential. Tin-doped indium oxide (ITO) substrates modified with the nanocomposites were used as LSPR chip for optical and electrochemical measurements simultaneously. The charge sensitivity of LSPR was verified with external electric potential modulation theoretically and experimentally. Through layer-by-layer self-assembly immobilization of glucose oxidase (GOD) on the LSPR chips, the charge transfer monitoring during the bioreaction of glucose catalysis was further demonstrated based on the bio-electron transfer modulation of LSPR. By equivalent circuit method, the charge density of the LSPR chip were detected with optical extinction peak shifts, and the limit of detection was about 0.51 μC/cm². This bio-electron transfer modulated LSPR provides a promising approach for the detection of spatial charge densities and the evaluation of bioreaction substances at different region of single chip.

Advances and applications of nanophotonic biosensors

Nanophotonic devices, which control light in subwavelength volumes and enhance light-matter interactions, have opened up exciting prospects for biosensing. Numerous nanophotonic biosensors have emerged to address the limitations of the current bioanalytical methods in terms of sensitivity, throughput, ease-of-use and miniaturization. In this Review, we provide an overview of the recent developments of label-free nanophotonic biosensors using evanescent-field-based sensing with plasmon resonances in metals and Mie resonances in dielectrics. We highlight the prospects of achieving an improved sensor performance and added functionalities by leveraging nanostructures and on-chip and optoelectronic integration, as well as microfluidics, biochemistry and data science toolkits. We also discuss open challenges in nanophotonic biosensing, such as reducing the overall cost and handling of complex biological samples, and provide an outlook for future opportunities to improve these technologies and thereby increase their impact in terms of improving health and safety.

Mirror-backed dielectric metasurface sensor with ultrahigh figure of merit based on a super-narrow Rayleigh anomaly

Plasmonic nanostructures with large local field enhancement have been extensively investigated for sensing applications. However, the quality factor and thus the sensing figure of merit are limited due to relatively high ohmic loss. Here we propose a novel, to the best of our knowledge, plasmonic sensor with an ultrahigh figure of merit based on a super-narrow Rayleigh anomaly (RA) in a mirror-backed dielectric metasurface. Simulation results show that the RA in such a metasurface can have a super-high quality factor of 16,000 in the visible regime, which is an order of magnitude larger than the highest value of reported plasmonic nanostructures. We attribute this striking performance to the enhanced electric fields far away from the metal film. The super-high quality factor and the greatly enhanced field confined to the superstrate region make the mirror-backed dielectric metasurface an ideal platform for sensing. We show that the figure of merit of this RA-based metasurface sensor can be as high as 15,930/refractive index units. Additionally, we reveal that RA-based plasmonic sensors share some typical characteristics, providing guidance for the structure design. We expect this work to advance the development of high-performance plasmonic metasurface sensors.

Detection of multiplex exosomal miRNAs for clinically accurate diagnosis of Alzheimer's disease using label-free plasmonic biosensor based on DNA-Assembled advanced plasmonic architecture

Alzheimer's disease (AD), the most common neurologic disorder, is characterized by progressive cognitive impairment. However, the low clinical significance of the currently used core AD biomarkers amyloid-beta and tau proteins remains a challenge. Recently, exosomes, found in human biological fluids, are gaining increasing attention because of their clinical significance in diagnosing of various diseases. In particular, blood-derived exosomal miRNAs are not only stable but also provide information regarding the different characteristics according to AD progression. However, quantitative and qualitative detection is difficult due to their characteristics, such as small size, low abundance, and high homology. Here, we present a DNA-assembled advanced plasmonic architecture (DAPA)-based plasmonic biosensor to accurately detect exosomal miRNAs in human serum. The designed nanoarchitecture possesses two narrow nanogaps that induce plasmon coupling; this significantly enhances its optical energy density, resulting in a 1.66-fold higher refractive-index (RI) sensitivity than nanorods at localized surface plasmon resonance (LSPR). Thus, the proposed biosensor is ultrasensitive and capable of selective single-nucleotide detection of exosomal miRNAs at the attomolar level. Furthermore, it identified AD patients from healthy controls by measuring the levels of exosomal miRNA-125b, miRNA-15a, and miRNA-361 in clinical serum samples. In particular, the combination of exosomal miRNA-125b and miRNA-361 showed the best diagnostic performance with a sensitivity of 91.67%, selectivity of 95.00%, and accuracy of 99.52%. These results demonstrate that our sensor can be clinically applied for AD diagnosis and has great potential to revolutionize the field of dementia research and treatment in the future.

Retention of Activity by Antibodies Immobilized on Gold Nanoparticles of Different Sizes: Fluorometric Method of Determination and Comparative Evaluation

Antibody–nanoparticle conjugates are widely used analytical reagents. An informative parameter reflecting the conjugates’ properties is the number of antibodies per nanoparticle that retain their antigen-binding ability. Estimation of this parameter is characterized by a lack of simple, reproducible methods. The proposed method is based on the registration of fluorescence of tryptophan residues contained in proteins and combines sequential measurements of first the immobilized antibody number and then the bound protein antigen number. Requirements for the measurement procedure have been determined to ensure reliable and accurate results. Using the developed technique, preparations of spherical gold nanoparticles obtained by the most common method of citrate reduction of gold salts (the Turkevich–Frens method) and varying in average diameter from 15 to 55 nm have been characterized. It was shown that the number of antibodies (immunoglobulins G) bound by one nanoparticle ranged from 30 to 194 during adsorptive unoriented monolayer immobilization. C-reactive protein was considered as the model antigen. The percentage of antibody valences that retained their antigen-binding properties in the conjugate increased from 17 to 34% with an increase in the diameter of gold nanoparticles. The proposed method and the results of the study provide tools to assess the capabilities of the preparations of gold nanoparticles and their conjugates as well as the expediency of seeking the best techniques for various practical purposes.

Nanoplasmonic biosensors: Theory, structure, design, and review of recent applications

Nanoplasmonic biosensing shows an immense potential to satisfy the needs of the global health industry - low-cost, fast, and portable automated systems; highly sensitive and real-time detection; multiplexing and miniaturization. In this review, we presented the theory of nanoplasmonic biosensing for popular detection schemes - SPR, LSPR, and EOT - and underline the consideration for nanostructure design, material selection, and their effects on refractometric sensing performance. Later, we covered the bottom-up and top-down nanofabrication methods for nanoplasmonic biosensors. Subsequently, we reviewed the recent examples of nanoplasmonic biosensors over a wide range of clinically relevant analytes in the diagnosis and prognosis of a wide range of diseases and conditions such as biomarker proteins, infectious bacteria, viral agents. Finally, we discussed the challenges of nanoplasmonic biosensing toward clinical translation and proposed strategic avenues to be competitive against current clinical detection methods. Hopefully, nanoplasmonic biosensing can realize its potential through successful demonstrations of clinical translation in the upcoming years.

Plasmonic Core-Shell-Satellites with Abundant Electromagnetic Hotspots for Highly Sensitive and Reproducible SERS Detection

In this work, we develop a Ag@Al2O3@Ag plasmonic core-shell-satellite (PCSS) to achieve highly sensitive and reproducible surface-enhanced Raman spectroscopy (SERS) detection of probe molecules. To fabricate PCSS nanostructures, we employ a simple hierarchical dewetting process of Ag films coupled with an atomic layer deposition (ALD) method for the Al2O3 shell. Compared to bare Ag nanoparticles, several advantages of fabricating PCSS nanostructures are discovered, including high surface roughness, high density of nanogaps between Ag core and Ag satellites, and nanogaps between adjacent Ag satellites. Finite-difference time-domain (FDTD) simulations of the PCSS nanostructure confirm an enhancement in the electromagnetic field intensity (hotspots) in the nanogap between the Ag core and the satellite generated by the Al2O3 shell, due to the strong core-satellite plasmonic coupling. The as-prepared PCSS-based SERS substrate demonstrates an enhancement factor (EF) of 1.7 × 107 and relative standard deviation (RSD) of ~7%, endowing our SERS platform with highly sensitive and reproducible detection of R6G molecules. We think that this method provides a simple approach for the fabrication of PCSS by a solid-state technique and a basis for developing a highly SERS-active substrate for practical applications.

High-throughput fabrication of high aspect ratio Ag/Al nanopillars for optical detection of biomarkers

Nanomaterial-based optical techniques for biomarker detection have garnered tremendous attention from the nanofabrication community due to their high precision and enhanced limit of detection (LoD) features. These nanomaterials are highly responsive to local refractive index (RI) fluctuations, and their RI unit sensitivity can be tuned by varying the chemical composition, geometry, and dimensions of the utilized nanostructures. To improve the sensitivity and LoD values of these nanomaterials, it is common to increase both dimensions and aspect ratios of the fabricated nanostructures. However, limited by the complexity, prolonged duration, and elevated costs of the available nanofabrication techniques, mass production of these nanostructures remains challenging. To address not only high accuracy, but also speed and production effectiveness in these nanostructures' fabrication, our work reports, for the first time, a fast, high-throughput, and cost-effective nanofabrication protocol for routine manufacturing of polymer-based nanostructures with high sensitivity and calculated LoD in the pM range by utilizing anodized aluminum oxide (AAO) membranes as templates. Specifically, our developed platform consists of arrays of nearly uniform polystyrene nanopillars with an average diameter of ∼185 nm and aspect ratio of ∼11. We demonstrate that these nanostructures can be produced at a high speed and a notably low price, and that they can be efficiently applied for biosensing purposes after being coated with aluminum-doped silver (Ag/Al) thin films. Our platform successfully detected very low concentrations of human C-reactive protein (hCRP) and SARS-CoV-2 spike protein biomarkers in human plasma samples with LoDs of 11 and 5 pM, respectively. These results open new opportunities for day-to-day fabrication of high aspect ratio arrays of nanopillars that can be used as a base for nanoplasmonic sensors with competitive LoD values. This, in turn, contributes to the development of point-of-care devices and further improvement of the existing nanofabrication techniques, thereby enriching the fields of pharmacology, clinical analysis, and diagnostics.

Optimization of Gold Nanorod Features for the Enhanced Performance of Plasmonic Nanocavity Arrays

Nanoplasmonic biosensors incorporating noble metal nanocavity arrays are widely used for the detection of various biomarkers. Gold nanorods (GNRs) have unique properties that can enhance spectroscopic detection capabilities of such nanocavity-based biosensors. However, the contribution of the physical properties of multiple GNRs to resonance enhancement of gold nanocavity arrays requires further characterization and elucidation. In this work, we study how GNR aspect ratio (AR) and surface area (SA) modify the plasmonic resonance spectrum of a gold triangular nanocavity array by both simulations and experiments. The finite integration technique (FIT) simulated the extinction spectrum of the gold nanocavity array with 300 nm periodicity onto which the GNRs of different ARs and SAs are placed. Simulations showed that matching of the GNRs longitudinal peak, which is affected by AR, to the nanocavity array's spectrum minima can optimize signal suppression and shifting. Moreover, increasing SA of the matched GNRs increased the spectral variations of the array. Experiments confirmed that GNRs conjugated to a gold triangular nanocavity array of 300 nm periodicity caused spectrum suppression and redshift. Our findings demonstrate that tailoring of the GNR AR and SA parameters to nanoplasmonic arrays has the potential to greatly improve spectral variations for enhanced plasmonic biosensing.

Fibre-Optic Surface Plasmon Resonance Biosensor for Monoclonal Antibody Titer Quantification

An extraordinary optical transmission fibre-optic surface plasmon resonance biosensing platform was engineered to improve its portability and sensitivity, and was applied to monitor the concentrations of monoclonal antibodies (Mabs). By refining the fabricating procedure and changing the material of the flow cell and the components of the optical fibre, the biosensor is portable and robust to external interference. After the implementation of an effective template cleaning procedure and precise control during the fabrication process, a consistent sensitivity of 509 ± 5 nm per refractive index unit (nm/RIU) was achieved. The biosensor can detect the Mab with a limit of detection (LOD) of 0.44 µg/mL. The results show that the biosensor is a potential tool for the rapid quantification of Mab titers. The biosensor can be regenerated at least 10 times with 10 mM glycine (pH = 2.5), and consistent signal changes were obtained after regeneration. Moreover, the employment of a spacer arm SM(PEG)2, used for immobilising protein A onto the gold film, was demonstrated to be unable to improve the detecting sensitivity; thus, a simple procedure without the spacer arm could be used to prepare the protein A-based biosensor. Our results demonstrate that the fibre-optic surface plasmon resonance biosensor is competent for the real-time and on-line monitoring of antibody titers in the future as a process analytical technologies (PATs) tool for bioprocess developments and the manufacture of therapeutic antibodies.

Scanning probe microscopy by localized surface plasmon resonance at fiber taper tips

Plasmonic antenna probes have been widely investigated for detecting electrical permittivity changes on the nanometer scale by employing high-sensitivity localized surface plasmon resonance (LSPR). Although it is intuitive to integrate such a probe onto an atomic force microscope (AFM) to add one more measurable quantity to the family of scanning probe microscopy techniques, the strong scattering background of the AFM tip overwhelms the LSPR scattering signal. To solve this problem, we combined evanescent coupling, polarization and spatial filtering, confocal spectroscopy, and numerical methods to extract clean LSPR spectra from a gold nanosphere-antenna probe attached to the tip of a fiber taper. By mounting the fiber taper on a custom quartz-tuning-fork SPM, we achieved high-quality nanometer-scale imaging of gold nanospheres on glass slides by mapping the LSPR wavelength shift. In addition, we reported an LSPR wavelength shift enhancement by more complicated probe designs and the consequent promise for higher-sensitivity microscopy. Our optical system and spectral processing method provide an effective solution to the long-standing quest for LSPR scanning microscopy.

A wafer-scale fabrication method for three-dimensional plasmonic hollow nanopillars

Access to nanofabrication strategies for crafting three-dimensional plasmonic structures is limited. In this work, a fabrication strategy to produce 3D plasmonic hollow nanopillars (HNPs) using Talbot lithography and I-line photolithography is introduced. This method is named subtractive hybrid lithography (SHL), and permits intermixed usage of nano-and-macroscale patterns. Sputter-redeposition of gold (Au) on the SHL resist pattern yields large areas of dense periodic Au-HNPs. These Au-HNPs are arranged in a square unit cell with a 250 nm pitch. The carefully controlled fabrication process resulted in Au-HNPs with nanoscale dimensions over the Au-HNP dimensions such as an 80 ± 2 nm thick solid base with a 133 ± 4 nm diameter, and a 170 ± 10 nm high nano-rim with a 14 ± 3 nm sidewall rim-thickness. The plasmonic optical response is assessed with FDTD-modeling and reveals that the highest field enhancement is at the top of the hollow nanopillar rim. The modeled field enhancement factor (EF) is compared to the experimental analytical field enhancement factor, which shows to pair up with ca. 10³ < EF < 10⁴ and ca. 10³ < EF < 10⁵ for excitation wavelengths of 633 and 785 nm. From a broader perspective, our results can stimulate the use of Au-HNPs in the fields of plasmonic sensors and spectroscopy.

Recent progress in plasmonic nanoparticle-based biomarker detection and cytometry for the study of central nervous system disorders

Neurological disorders affect hundreds of millions of people around the world, are often life-threatening, untreatable, and can result in debilitating symptoms. The high prevalence of these disorders, which feature biochemical or structural abnormalities in neuronal systems, has spurned innovations in both rapid and early detection to assist in the selection of appropriate treatment strategies to improve the patients' quality of life. Plasmonic nanoparticles (PNPs), a versatile and promising class of nanomaterials, are widely utilized in numerous imaging techniques, drug delivery systems, and biomarker detection methods. Recently, PNP-based nanoprobes have attracted considerable attention for the early diagnosis of neurological disorders. Gold nanoparticles (AuNPs), with high local surface plasmon resonance (LSPR) signals, have been particularly well exploited as probes for dynamic biomarker detection, with quantification sensitivity demonstrated down to the single-molecule level. In this review, we will discuss the possibilities of PNPs in the methodological development for rapid neurological disease identification. In addition, we will also describe a new digital cytometry method that combines dark-field imaging and machine learning for precise biomarker enumeration on single cells. The aim of this review is to attract researchers working on the future development of new plasmonic nanoprobe-based strategies for the diagnosis of neurological disorders.

Plasmonic mode coupling and thin film sensing in metal-insulator-metal structures

Optical sensors based on surface plasmon resonance (SPR) in the attenuated total reflection (ATR) configuration in layered media have attracted considerable attention over the past decades owing to their ability of label free sensing in biomolecular interaction analysis, and highly sensitive detection of changes in refractive index and thickness, i.e. the optical thickness, of thin film adsorbates (thin film sensing). Furthermore, SPR is highly sensitive to the refractive index of the medium adjacent to the bare metal, and it allows for bulk sensing as well. When deposited at the metal/air interface, an adsorbed layer disturbs the highly localized, i.e. bound, wave at this interface and changes the plasmon resonance to allow for sensing in angular or wavelength interrogation and intensity measurement modes. A high degree of sensitivity is required for precise and efficient sensing, especially for biomolecular interaction analysis for early stage diagnostics; and besides conventional SPR (CSPR), several other configurations have been developed in recent years targeting sensitivity, including long-range SPR (LRSPR) and waveguide-coupled SPR (WGSPR) observed in MIM structures, referred here to by MIM modes, resulting from the coupling of SPRs at I/M interfaces, and Fano-type resonances occurring from broad and sharp modes coupling in layered structures. In our previous research, we demonstrated that MIM is better than CSPR for bulk sensing, and in this paper, we show that CSPR is better than MIM for thin film sensing for thicknesses of the sensing layer (SL) larger than 10 nm. We discuss and compare the sensitivity of CSPR and MIM for thin film sensing by using both experiments and theoretical calculations based on rigorous electromagnetic (EM) theory. We discuss in detail MIM modes coupling and anti-crossing, and we show that when a thin film adsorbate, i.e. a SL), is deposited on top of the outermost-layer of an optimized MIM structure, it modifies the characteristics of the coupled modes of the structure, and it reduces the electric field, both inside the SL and at the SL/air interface, and as a result, it decreases the sensitivity of the MIM versus the CSPR sensor. Our work is of critical importance to plasmonic mode coupling using MIM configurations, as well as to optical bio- and chemical-sensing.

Unraveling How Multivalency Triggers Shape Deformation of Sub-100 nm Lipid Vesicles

Multivalent ligand-receptor interactions are critical to the function of membrane-enveloped biological and biomimetic nanoparticles, yet resulting nanoparticle shape changes are rarely investigated. Using the localized surface plasmon resonance (LSPR) sensing technique, we tracked the attachment of biotinylated, sub-100 nm lipid vesicles to a streptavidin-functionalized supported lipid bilayer (SLB) and developed an analytical model to extract quantitative details about the vesicle-SLB contact region. The experimental results were supported by theoretical analyses of biotin-streptavidin complex formation and corresponding structural and energetic aspects of vesicle deformation. Our findings reveal how varying the surface densities of streptavidin receptors in the SLB and biotin ligands in the vesicles affects the extent of nanometer-scale vesicle deformation. We also identify conditions, i.e., a critical ligand density, at which appreciable vesicle deformation began, which provides insight into how the membrane bending energy partially counterposes the multivalent binding interaction energy. These findings are generalizable to various multivalent ligand-receptor systems.

Microfluidics-Based Plasmonic Biosensing System Based on Patterned Plasmonic Nanostructure Arrays

This review aims to summarize the recent advances and progress of plasmonic biosensors based on patterned plasmonic nanostructure arrays that are integrated with microfluidic chips for various biomedical detection applications. The plasmonic biosensors have made rapid progress in miniaturization sensors with greatly enhanced performance through the continuous advances in plasmon resonance techniques such as surface plasmon resonance (SPR) and localized SPR (LSPR)-based refractive index sensing, SPR imaging (SPRi), and surface-enhanced Raman scattering (SERS). Meanwhile, microfluidic integration promotes multiplexing opportunities for the plasmonic biosensors in the simultaneous detection of multiple analytes. Particularly, different types of microfluidic-integrated plasmonic biosensor systems based on versatile patterned plasmonic nanostructured arrays were reviewed comprehensively, including their methods and relevant typical works. The microfluidics-based plasmonic biosensors provide a high-throughput platform for the biochemical molecular analysis with the advantages such as ultra-high sensitivity, label-free, and real time performance; thus, they continue to benefit the existing and emerging applications of biomedical studies, chemical analyses, and point-of-care diagnostics.

Nanophotonic biosensors harnessing van der Waals materials

Low-dimensional van der Waals (vdW) materials can harness tightly confined polaritonic waves to deliver unique advantages for nanophotonic biosensing. The reduced dimensionality of vdW materials, as in the case of two-dimensional graphene, can greatly enhance plasmonic field confinement, boosting sensitivity and efficiency compared to conventional nanophotonic devices that rely on surface plasmon resonance in metallic films. Furthermore, the reduction of dielectric screening in vdW materials enables electrostatic tunability of different polariton modes, including plasmons, excitons, and phonons. One-dimensional vdW materials, particularly single-walled carbon nanotubes, possess unique form factors with confined excitons to enable single-molecule detection as well as in vivo biosensing. We discuss basic sensing principles based on vdW materials, followed by technological challenges such as surface chemistry, integration, and toxicity. Finally, we highlight progress in harnessing vdW materials to demonstrate new sensing functionalities that are difficult to perform with conventional metal/dielectric sensors.

This review presents an overview of scenarios where van der Waals (vdW) materials provide unique advantages for nanophotonic biosensing applications. The authors discuss basic sensing principles based on vdW materials, advantages of the reduced dimensionality as well as technological challenges.

Time-Resolved and Label-Free Evanescent Light-Scattering Microscopy for Mass Quantification of Protein Binding to Single Lipid Vesicles

In-depth understanding of the intricate interactions between biomolecules and nanoparticles is hampered by a lack of analytical methods providing quantitative information about binding kinetics. Herein, we demonstrate how label-free evanescent light-scattering microscopy can be used to temporally resolve specific protein binding to individual surface-bound (∼100 nm) lipid vesicles. A theoretical model is proposed that translates protein-induced changes in light-scattering intensity into bound mass. Since the analysis is centered on individual lipid vesicles, the signal from nonspecific protein binding to the surrounding surface is completely avoided, offering a key advantage over conventional surface-based techniques. Further, by averaging the intensities from less than 2000 lipid vesicles, the sensitivity is shown to increase by orders of magnitude. Taken together, these features provide a new avenue in studies of protein-nanoparticle interaction, in general, and specifically in the context of nanoparticles in medical diagnostics and drug delivery.

Imaging-based spectrometer-less optofluidic biosensors based on dielectric metasurfaces for detecting extracellular vesicles

Biosensors are indispensable tools for public, global, and personalized healthcare as they provide tests that can be used from early disease detection and treatment monitoring to preventing pandemics. We introduce single-wavelength imaging biosensors capable of reconstructing spectral shift information induced by biomarkers dynamically using an advanced data processing technique based on an optimal linear estimator. Our method achieves superior sensitivity without wavelength scanning or spectroscopy instruments. We engineered diatomic dielectric metasurfaces supporting bound states in the continuum that allows high-quality resonances with accessible near-fields by in-plane symmetry breaking. The large-area metasurface chips are configured as microarrays and integrated with microfluidics on an imaging platform for real-time detection of breast cancer extracellular vesicles encompassing exosomes. The optofluidic system has high sensing performance with nearly 70 1/RIU figure-of-merit enabling detection of on average 0.41 nanoparticle/µm2 and real-time measurements of extracellular vesicles binding from down to 204 femtomolar solutions. Our biosensors provide the robustness of spectrometric approaches while substituting complex instrumentation with a single-wavelength light source and a complementary-metal-oxide-semiconductor camera, paving the way toward miniaturized devices for point-of-care diagnostics.

Progress in the research of nanomaterial-based exosome bioanalysis and exosome-based nanomaterials tumor therapy

Exosomes and their internal components have been proven to play critical roles in cell-cell interactions and intrinsic cellular regulations, showing promising prospects in both biomedical and clinical fields. Although conventional methods have so far been utilized to great effect, accurate bioanalysis remains a major challenge. In recent years, the fast-paced development of nanomaterials with unique physiochemical properties has led to a boom in the potential bioapplications of such materials. In particular, the application of nanomaterials in exosome bioanalysis provides a great opportunity to overcome the current challenges and limitations of conventional methods. A timely review of the research progress in this field is thus of great significance to the continued development of new methods. This review outlines the properties and potential uses of exosomes, and discusses the conventional methods currently used for their analysis. We then focus on exploring the current state of the art regarding the use of nanomaterials for the isolation, detection and even the subsequent profiling of exosomes. The main methods are based on principles including fluorescence, surface-enhanced Raman spectroscopy, colorimetry, electrochemistry, and surface plasmon resonance. Additionally, research on exosome-based nanomaterials tumor therapy is also promising from a clinical perspective, so the research progress in this branch is also summarized. Finally, we look at ways in which the field might develop in the future.

Extraordinary sensitivity enhancement of Ag-Au alloy nanohole arrays for label-free detection of Escherichia Coli

Alloy nanostructures unveil extraordinary plasmonic phenomena that supersede the mono-metallic counterparts. Here we report silver-gold (Ag-Au) alloy nanohole arrays (α-NHA) for ultra-sensitive plasmonic label-free detection of Escherichia Coli (E. coli). Large-area α-NHA were fabricated by using nanoimprint lithography and concurrent thermal evaporation of Ag and Au. The completely miscible Ag-Au alloy exhibits an entirely different dielectric function in the near infra-red wavelength range compared to mono-metallic Ag or Au. The α-NHA demonstrate substantially enhanced refractive index sensitivity of 387 nm/RIU, surpassing those of Ag or Au mono-metallic nanohole arrays by approximately 40%. Moreover, the α-NHA provide highly durable material stability to corrosion and oxidation during over one-month observation. The ultra-sensitive α-NHA allow the label-free detection of E. coli in various concentration levels ranging from 10³ to 10⁸ cfu/ml with a calculated limit of detection of 59 cfu/ml. This novel alloy plasmonic material provides a new outlook for widely applicable biosensing and bio-medical applications.

Gold Nanoparticles in Cancer Theranostics

Conventional cancer treatments, such as surgical resection, radiotherapy, and chemotherapy, have achieved significant progress in cancer therapy. Nevertheless, some limitations (such as toxic side effects) are still existing for conventional therapies, which motivate efforts toward developing novel theranostic avenues. Owning many merits such as easy surface modification, unique optical properties, and high biocompatibility, gold nanoparticles (AuNPs and GNPs) have been engineered to serve as targeted delivery vehicles, molecular probes, sensors, and so on. Their small size and surface characteristics enable them to extravasate and access the tumor microenvironment (TME), which is a promising solution to realize highly effective treatments. Moreover, stimuli-responsive properties (respond to hypoxia and acidic pH) of nanoparticles to TME enable GNPs’ unrivaled control for effective transport of therapeutic cargos. In this review article, we primarily introduce the basic properties of GNPs, further discuss the recent progress in gold nanoparticles for cancer theranostics, with an additional concern about TME stimuli-responsive studies.

Quantum Plasmonic Sensors

The extraordinary sensitivity of plasmonic sensors is well-known in the optics and photonics community. These sensors exploit simultaneously the enhancement and the localization of electromagnetic fields close to the interface between a metal and a dielectric. This enables, for example, the design of integrated biochemical sensors at scales far below the diffraction limit. Despite their practical realization and successful commercialization, the sensitivity and associated precision of plasmonic sensors are starting to reach their fundamental classical limit given by quantum fluctuations of light-known as the shot-noise limit. To improve the sensing performance of these sensors beyond the classical limit, quantum resources are increasingly being employed. This area of research has become known as "quantum plasmonic sensing", and it has experienced substantial activity in recent years for applications in chemical and biological sensing. This review aims to cover both plasmonic and quantum techniques for sensing, and it shows how they have been merged to enhance the performance of plasmonic sensors beyond traditional methods. We discuss the general framework developed for quantum plasmonic sensing in recent years, covering the basic theory behind the advancements made, and describe the important works that made these advancements. We also describe several key works in detail, highlighting their motivation, the working principles behind them, and their future impact. The intention of the review is to set a foundation for a burgeoning field of research that is currently being explored out of intellectual curiosity and for a wide range of practical applications in biochemistry, medicine, and pharmaceutical research.