Facile hydrothermal synthesis of a tri-metallic Cu-Mn-Ni oxide-based electrochemical pseudo capacitor

Transition metal oxide nanocomposites with heterostructures have gained a lot of attention for use in supercapacitors owing to their low cost, high surface area, fast transport of ions and electrons and high specific capacitance due to efficacious interplay between the electrode and the electrolytes. In this study, we fabricated tri-metallic Cu, Mn, Ni(CMNO), bi-metallic Mn, Ni(MNO) and mono-metallic Ni(NO) oxides through a facile hydrothermal route. All the fabricated materials were characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and energy dispersive spectroscopy (EDX), and their electrochemical properties were studied using cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and galvanostatic charge-discharge (GCD). The CMNO material showed remarkable electrochemical performance with a specific capacitance of 790.63 F g-1 at a current density of 1 A g-1, surpassing the performance of MNO (438.4 F g-1) and NO (290.82 F g-1). Furthermore, CMNO showed high cycling stability with a retention of 96.7% specific capacitance after 8000 cycles. Based on remarkable and unique properties, the CMNO material is regarded as a promising material for new-generation pseudo-capacitor applications.

Electrocatalytic Properties of Quasi-2D Oxides LaSrMn0.5M0.5O4 (M = Co, Ni, Cu, and Zn) for Hydrogen and Oxygen Evolution Reactions

Designing cost-effective and highly efficient electrocatalysts for water splitting is a significant challenge. We have systematically investigated a series of quasi-2D oxides, LaSrMn0.5M0.5O4 (M = Co, Ni, Cu, Zn), to enhance the electrocatalytic properties of the two half-reactions of water-splitting, namely oxygen and hydrogen evolution reactions (OER and HER). The four materials are isostructural, as confirmed by Rietveld refinements with X-ray diffraction. The oxygen contents and metal valence states were determined by iodometric titrations and X-ray photoelectron spectroscopy. Electrical conductivity measurements in a wide range of temperatures revealed semiconducting behavior for all four materials. Electrocatalytic properties were studied for both half-reactions of water-splitting, namely, oxygen-evolution and hydrogen-evolution reactions (OER and HER). For the four materials, the trends in both OER and HER were the same, which also matched the trend in electrical conductivities. Among them, LaSrMn0.5Co0.5O4 showed the best bifunctional electrocatalytic activity for both OER and HER, which may be attributed to its higher electrical conductivity and favorable electron configuration.

Novel Heterostructure-Based CoFe and Cobalt Oxysulfide Nanocubes for Effective Bifunctional Electrocatalytic Water and Urea Oxidation

The development of effective oxygen evolution reaction (OER) and urea oxidation reaction (UOR) on heterostructure electrocatalysts with specific interfaces and characteristics provides a distinctive character. In this study, heterostructure nanocubes (NCs) comprising inner cobalt oxysulfide (CoOS) NCs and outer CoFe (CF) layered double hydroxide (LDH) are developed using a hydrothermal methodology. During the sulfidation process, the divalent sulfur ions (S2-) are released from the breakdown of the sulfur source and react with the Co-precursors on the surface leading to the transformation of CoOH nanorods into CoOS nanocubes. Further, X-ray photoelectron spectroscopy (XPS) and X-ray absorption spectroscopy (XAS) analyses reveal that the interactions at the interface of the CF@CoOS NCs significantly altered the electronic structure, thus enhancing the electrocatalytic performance. The optimal catalysts exhibited effective OER and UOR activities, the attained potentials are 1.51 and 1.36 V. This remarkable performance is attributable to the induction of electron transfer from the CoFe LDH to CoOS, which reduces the energy barrier of the intermediates for the OER and UOR. Furthermore, an alkaline water and urea two-cell electrolyzer assembled using CF@CoOS-2 NCs and Pt/C as the anode and cathode requires a cell voltage of 1.63 and 1.56 V along with a durability performance.

Promoting H2 generation of BiFeO3 photocathodes by a catalyst-sensitizer dyad linked with Sn(dipicolinate)2

An innovative method for the fabrication of a catalyst-sensitizer dyad-based photoelectrode was developed by using the coordinated interaction between the pyridine-2,6-dicarboxylic group and Sn4+. A dyad (C1 + PDI) was loaded on the mesoporous BiFeO3 (BFO) photocathode for light-driven H2 generation. The dyad could expand the light absorption range and promote the surface charge separation of BFO, resulting in an enhanced photocurrent.

Mechanistic Insights into the Synthesis of Nickel-Graphene Nanostructures for Gas Sensors

Toxic gases are used in different types of industries and thus, present a potential health hazard. Therefore, highly sensitive gas sensing materials are essential for the safety of those operating in their environments. A process involving electrospinning polymer solutions impregnated with transition metal ions are developed to yield nanofibers that are annealed to form graphitic carbon / nickel nanoparticle-based fibers for gas sensing applications. The performance of these gas sensors is strongly related to the ability to control the material parameters of the active material. As the formation of these nanostructures, which nucleate within solid carbon scaffolds, have not been investigated, the growth mechanisms are look to understand in order to exert control over the resulting material. Evaluation of these growth mechanisms are conducted through a combination of thermogravimetric analysis with mass spectrometry (TGA-MS), x-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and x-ray photoelectron spectroscopy (XPS) and reveal nucleation of nickel at the onset of the polymer scaffold decomposition with subsequent growth processes, including surface diffusion, aggregation, coalescence and evaporation condensation, that are activated at different temperatures. Gas sensing experiments conducted on analyte gases demonstrate good sensitivity and response times, and significant potential for use in other energy and environmental applications.

Multi-Active Sites Loaded NiCu-MOF@MWCNTs as a Bifunctional Electrocatalyst for Electrochemical Water Splitting Reaction

Water can be sustainably and ecologically converted by electrocatalysts into hydrogen and oxygen, which, in turn, can be converted into energy. However, the advancement of using water as green energy is hampered by limitations in the study of high-performance catalysts. The purpose of this study was to construct an electrocatalyst by anchoring well-dispersed multiwalled carbon nanotubes (MWCNTs) on nickel-copper (NiCu-MOF) nanoblocks through a simple solvothermal method. The synthesis of NiCu-MOF@MWCNTs demonstrated exceptional electrocatalytic performance for the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) in an alkaline medium. At 10 mA cm-2 in 1.0 M KOH, the OER and HER performance of the catalyst displays a relatively low overpotential, with only 220 and 78 mV, respectively. Furthermore, the catalytic activity remained unchanged for 24 h in 1.0 M KOH. This performance was superior to the majority of electrocatalysts that have been reported. This was achieved by utilizing the strong synergy that exists between MWCNTs and bimetallic (Ni-Cu) nano blocks present in the metal-organic framework. The enhanced electrocatalytic activity of the nanocomposite can be attributed to the synergistic impact caused by its various components.

Guided Design of Efficient Oxygen Evolution Catalysts Using Patent Analysis

The facile and rapid design of efficient oxygen evolution reaction (OER) catalysts holds paramount significance for energy conversion devices, such as water electrolyzers and fuel cells. Despite substantial progress in catalyst synthesis and performance exploration, the design and selection processes remain inefficient. In this context, we integrate patent analysis with catalyst design, leveraging the scholarly research functionalities within patent analyses to aid in the design and synthesis of a NiFeRu-carbon catalyst as a high-performance OER catalyst. The results demonstrate that the NiFeRu-Carbon catalyst with low Ru loading (0.3 wt %) exhibits an overpotential of only 219 mV at 10 mA cm-2 under alkaline conditions, and after continuous operation for 200 h, the overpotential only attenuates by 15 mV. The incorporation of high-valence Ru dopants elevated the intrinsic activity of individual catalytic sites within NiFe-layered double hydroxides (LDHs). During the catalytic process, the partial dissolution of Ru might lead to the generation of numerous oxygen vacancies within NiFe- LDH, thereby enhancing the catalyst's activity and stability.

Solid state engineering of Bi2S3/rGO nanostrips: an excellent electrode material for energy storage applications

The study presents a novel, one-pot, and scalable solid-state reaction scheme to prepare bismuth sulphide (Bi2S3)-reduced graphene oxide (rGO) nanocomposites using bismuth oxide (Bi2O3), thiourea (TU), and graphene oxide (GO) as starting materials for energy storage applications. The impact of GO loading concentration on the electrochemical performance of the nanocomposites was investigated. The reaction follows a diffusion substitution pathway, gradually transforming Bi2O3 powder into Bi2S3 nanostrips, concurrently converting GO into rGO. Enhanced specific capacitances were observed across all nanocomposite samples, with the Bi2S3@0.2rGO exhibiting the highest specific capacitance of 705 F g-1 at a current density of 1 A g-1 and maintaining a capacitance retention of 82% after 1000 cycles. The superior specific capacitance is attributed to the excellent homogeneity and synergistic relation between rGO and Bi2S3 nanostrips. This methodology holds promise for extending the synthesis of other chalcogenides-rGO nanocomposites.

Photocatalytic degradation of brilliant green and 4-nitrophenol using Ni-doped Gd(OH)3 nanorods

Gadolinium hydroxide (Gd(OH)3) was synthesized via a microwave-assisted synthesis method. Nickel ion (Ni2+) was doped into Gd(OH)3, in which 4-12% Ni-Gd(OH)3 was synthesized, to study the effect of doping. The structural, optical, and morphological properties of the synthesized materials were analyzed. The crystallite sizes of the hexagonal structure of Gd(OH)3 and Ni-Gd(OH)3, which were 17-30 nm, were obtained from x-ray diffraction analysis. The vibrational modes of Gd(OH)3 and Ni-Gd(OH)3 were confirmed using Raman and Fourier-transform infrared spectroscopies. The band gap energy was greatly influenced by Ni-doping, in which a reduction of the band gap energy from 5.00 to 3.03 eV was observed. Transmission electron microscopy images showed nanorods of Gd(OH)3 and Ni-Gd(OH)3 and the particle size increased upon doping with Ni2+. Photocatalytic degradations of brilliant green (BG) and 4-nitrophenol (4-NP) under UV light irradiation were carried out. In both experiments, 12% Ni-Gd(OH)3 showed the highest photocatalytic response in degrading BG and 4-NP, which is about 92% and 69%, respectively. Therefore, this study shows that Ni-Gd(OH)3 has the potential to degrade organic pollutants.

Highly Porous Carbon Flakes Derived from Cellulose and Nickel Phosphide Heterostructure towards Efficient Electrocatalysis of Oxygen Evolution Reaction

This study delves into the pressing challenges of climate change and the escalating carbon dioxide (CO2) emissions by exploring hydrogen technology as a sustainable alternative. In particular, there is focus on nickel phosphide-based electrocatalysts, known for their promising performance in hydrogen evolution reactions (HERs) and oxygen evolution reactions (OERs). Therefore, here we have designed a facile strategy to deliver highly porous carbon flakes derived from cellulose fibers via carbonization at 850 °C, yielding highly porous structures and outstanding specific surface area (SSAcel_carb_850_act = 3164 m2/g) after activation. As-fabricated carbon was utilized as a support for Ni12P5 with an optimized mass ratio. Electrochemical testing revealed that the composite of Ni12P5 and carbon flakes with a ratio of 100:1, respectively, exhibited the most favorable kinetics for the oxygen evolution reaction (OER). Importantly, the durability tests of this sample demonstrated the most stable behavior and lowest potential change under high current density among the studied samples, making it a promising candidate in practical applications. Moreover, the analysis of electrocatalysts after an OER does not show any changes, indicating that the sample does not undergo undesired intermediate reactions and that unwanted products are not released, explaining its stable behavior. This provides a straightforward approach for creating a cellulose-derived composite with enhanced electroactivity and durability.

Biosynthesis of JC-La2CoO4 magnetic nanoparticles explored in catalytic and SMMs properties

We have reported the synthesis of JC-La2CoO4 magnetic nanoparticles from Jatropha Curcas L. leaf extract in aqueous medium and potential application study in catalytic & Single Molecule Magnets (SMMs). Several techniques were used to investigate the structural, morphological, and elemental composition, particle size, optical properties, catalytic and magnetic properties by XRD, FTIR, SEM, EDAX, XPS, UV-visible and squid magnetic measurement. It was found that the crystallite sizes and grain sizes of JC-La2CoO4 NPs were 11.3 ± 1 and 24.1 ± 1 nm respectively and surface morphology of the nanoparticles looks spherical shape with good surface area. The band gap of JC-La2CoO4 was found to be 4.95 eV indicates good semiconductor in nature. XPS studies shows that La and Co present in + 3 and + 2 oxidation state respectively and suggest the composition formula is La2CoO4 with satisfied all the valency of metal ions. The photocatalytic efficiency of La2CoO4 shows good result against methylene blue (MB) compared to other dyes like MO, NO, RhB in presence of sunlight with rate constant 56.73 × 10-3 min-1 and completely degraded within 115 mints. The importance of JC-La2CoO4 has magnetic properties with antiferromagnetic coupling and SMMs properties with nature.

Coordination Engineering of Dual Co, Ni Active Sites in N-Doped Carbon Fostering Reversible Oxygen Electrocatalysis

The development of affordable and non-noble-metal-based reversible oxygen electrocatalysts is required for renewable energy conversion and storage systems like metal-air batteries (MABs). However, the nonbifunctionality of most of the catalysts impedes their use in rechargeable MAB applications. Moreover, the loss of active sites also affects the long-term performance of the electrocatalyst toward oxygen electrocatalysis. In this work, we report a simplistic yet controllable chemical approach for the synthesis of dual transitional metals such as cobalt, nickel, and nitrogen-doped carbon (CoNi-NC) as bifunctional electrode materials for rechargeable zinc-air batteries (ZABs). The spatially isolated Ni-N4 and Co-N4 active units were rendered for oxygen reduction reaction (ORR) and oxygen evolution reaction (OER), respectively. The individual efficacy of both reversible reactions enables an ΔE value of ∼0.72 V, which outperforms several bifunctional electrocatalysts reported in the literature. The half-wave potential (E1/2) and overpotential were achieved at 0.83 V and 330 mV (vs RHE) for ORR and OER, respectively. The peak power density of ZAB equipped with the CoNi-NC catalyst was calculated to be 194 mW cm-2. The present strategy for the synthesis of bifunctional electrocatalysts with dual active sites offers prospects for developing electrochemical energy storage and conversion systems.

Synthesis of Hollow Leaf-Shaped Iron-Doped Nickel–Cobalt Layered Double Hydroxides Using Two-Dimensional (2D) Zeolitic Imidazolate Framework Catalyzing Oxygen Evolution Reaction

Layered double hydroxides (LDHs) have been reported as one of the most effective materials for oxygen evolution reaction (OER) catalysts, which are prone to hydrolysis and oxidation under OER conditions. Metal–organic frameworks (MOFs) are porous materials with high crystallinity and internal surface area. The design of LDHs based on MOFs has attracted increasing attention owing to their high surface area, exposed catalysis sites, and fast charge/mass transport kinetics. Herein, we report a novel approach to fabricate a leaf-shaped iron-doped nickel–cobalt LDH (L-Fe-NiCoLDH) derived from a two-dimensional (2D) zeolitic imidazolate framework with a leaf-like morphology (ZIFL). Iron doping played a significant role in enhancing the specific surface area, affecting the OER performance. L-Fe-NiCoLDH showed high OER performance with an overpotential of 243 mV at 10 mA cm−2 and high durability after 20 h. The design of LDHs based on the leaf morphology of MOFs offers tremendous potential for improving OER efficiency.

The first structural, morphological and magnetic property studies on spinel nickel cobaltite nanoparticles synthesized from non-standard reagents

In this paper, using a molten salt process, nickel cobaltite nanoparticles were successfully synthesized for the first time from non-standard reagents.

Carbon supported Pd based catalysts for the hydrolytic dehydrogeneration of morpholine borane

Although the reducing property of morpholine borane is frequently used, there are few studies on its use as a chemical hydrogen storage material. This study presents the catalyst efficiency for hydrogen production in the dehydrogenation reaction of morpholine borane as efficient and cost-effective hydrogen storage material, which can be used as an alternative to depleting fossil fuels. It was studied with four different catalysts as activated Carbon-supported Pd, PdAg, PdNi, and PdCo. Bimetallic palladium based catalysts were used for the dehydrogenation of morpholine borane for the first time. Nanoparticles were synthesized using the chemical reduction method. The catalytic effects of different metal ratios of PdNi/C nanoparticles, which were concluded to have the best catalyst effect, were investigated and it was observed that the ratio of Pd₅₀Ni₅₀/C nanoparticles exhibited better catalytic behavior, and optimization studies were carried out with Pd₅₀Ni₅₀/C nanoparticles. Transmission Electron Microscopy, X-Ray Diffraction, and X-Ray Photoelectron Spectroscopy analyzes were performed for the characterization of nanoparticles. According to the characterization analyzes of Pd₅₀Ni₅₀/C nanoparticles, the mean particle size was determined as 2.0 ± 1.0 nm. Catalyst efficiency was determined by performing the substrate, catalyst, and temperature experiments separately in the dehydrogenation reaction of Morpholine Borane. These parameters are respectively; Ea and ΔH were calculated as 93.2 kJ/mol, and 90.6 kJ/mol. The reusability experiments were carried out in 4 cycles. In other words, with this study, it was concluded that the reusability of Pd₅₀Ni₅₀/C nanoparticles synthesized by the chemical method is high and their catalytic activity is excellent.

Novel Indium Vanadium Oxide Nanosheet-Supported Nickel Iron Oxide Nanoplate Heterostructure for Synergistically Enhanced Photocatalytic Degradation of Tetracycline

Semiconductor-based heterogeneous photocatalytic oxidation processes have received considerable attention for the remediation of toxic pollutants. Herein, InVO4/NiFe2O4 nanocomposites were synthesized using a facile hydrothermal technique. Furthermore, various characterization results revealed the successful loading of NiFe2O4 nanoplates over InVO4 nanosheets, thereby signifying the formation of a heterostructure. The performance of the synthesized photocatalyst was tested for tetracycline (TC) antibiotic removal. The optimized InVO4/NiFe2O4 nanocomposite exhibits maximum photodegradation of TC molecules (96.68%) in 96 min; this is approximately 6.47 and 4.93 times higher than that observed when using NiFe2O4 and InVO4, respectively. The strong interaction between the InVO4 nanosheets and NiFe2O4 nanoplates can improve the visible-light absorption and hinder the recombination of charge carriers, further enhancing the photocatalytic performance. Moreover, hydroxyl radicals play a crucial role in the photodegradation of TC antibiotics.

Facile Synthesis of NiCo2S4/rGO Composites in a Micro-Impinging Stream Reactor for Energy Storage

Using a process-enhanced micro-impinging stream reactor (MISR) and a co-precipitation route, NiCo2S4 and NiCo2S4/rGO electrode materials were successfully prepared, respectively. Owing to its excellent micromixing performance, the MISR-prepared NiCo2S4/rGO composites had a smaller size and less agglomeration than the same composites prepared in a traditional stirred reactor (STR). The specific capacity of the MISR-prepared composites was as high as 198.0 mAh g−1 under the current density of 1 A g−1. The cycling stability of the composites also improved significantly after being modified with reduced graphene oxide (rGO), and they displayed a fine cycling stability, which maintained a retention rate of 83.6% after 1000 cycles of charging and discharging.

Controllable Transformation of Metal-Organic Framework Nanosheets into Oxygen Vacancy NixCo3-xO4 Arrays for Ultrahigh-Capacitance Supercapacitors with Long Lifespan

The amino-functionalized bimetal NH₂-NiCo-MOF nanosheet array is first fabricated on Ni foam substrates and then controllably transformed into oxygen vacancy bimetal oxide arrays by simply thermal annealing in air. This NiCo-based oxide array (Ni_xCo_3-xO₄/NF) achieves high capacitance (2484 F g^-1 at 1 A g^-1), excellent rate performance (91.4%), and long cycling life when assessed as promising electrode material for supercapacitors. Notably, the existing oxygen vacancy in Ni_xCo_3-xO₄ promotes the electrochemical performance of Ni_xCo_3-xO₄/NF due to the enhancement of electrical conductivity and capture capability for OH^-. In addition, the assembled asymmetric supercapacitor (ASC) device exhibits an excellent energy density of 39.3 W h kg^-1 at a power density of 800.2 W kg^-1, which still remains 32.2 W h kg^-1 even at a high power density of 7994.5 W kg^-1. Furthermore, a light-emitting diode can be lightened for more than 6 min, demonstrating a great potential for practical application of ASC devices. This work knocks on the door of a feasible strategy for designing and synthesizing 2D metal oxide nanosheet arrays with excellent electrochemical properties.

Preparation and application of a flower-rod-like Bi2S3/Co3O4/rGO/nickel foam supercapacitor electrode

Herein, we have prepared a new nanocomposite Bi2S3/Co3O4/rGO/Ni foam substrate electrode through hydrothermal synthesis and an annealing process.

Catalytic performance of mixed MxCo3−xO4 (M = Cr, Fe, Mn, Ni, Cu, Zn) spinels obtained by combustion synthesis for preferential carbon monoxide oxidation (CO-PROX): insights into the factors controlling catalyst selectivity and activity

A series of mixed cobalt spinel catalysts (MxCo3−xO4 (M = Cr, Fe, Mn, Ni, Cu, Zn)) was synthesized and tested in the CO-PROX reaction and in sole CO oxidation and H2 oxidation as references.

Floating Carbon-Doped TiO2 Photocatalyst with Metallic Underlayers Investigation for Polluted Water Treatment under Visible-Light Irradiation

In the current study, we analysed the influence of metallic underlayers on carbon-doped TiO2 films for RhB decomposition and Salmonella typhimurium inactivation under visible-light irradiation. All the experiments were divided into two parts. First, layered M/C-doped-TiO2 film structures (M = Ni, Nb, Cu) were prepared by magnetron sputtering technique on borosilicate glass substrates in the two-step deposition process. The influence of metal underlayer on the formation of the carbon-doped TiO2 films was characterised by X-ray diffractometer, scanning electron microscope, and atomic force microscope. The comparison between the visible-light assisted photocatalytic activity of M/C-doped TiO2 structures was performed by the photocatalytic bleaching tests of Rhodamine B dye aqueous solution. The best photocatalytic performance was observed for Ni/C-doped-TiO2 film combination. During the second part of the study, the Ni/C-doped-TiO2 film combination was deposited on high-density polyethylene beads which were selected as a floating substrate. The morphology and surface chemical analyses of the floating photocatalyst were performed. The viability and membrane permeability of Salmonella typhimurium were tested in cycling experiments under UV-B and visible-light irradiation. Three consecutive photocatalytic treatments of fresh bacteria suspensions with the same set of floating photocatalyst showed promising results, as after the third 1 h-long treatment bacteria viability was still reduced by 90% and 50% for UV-B and visible-light irradiation, respectively. The membrane permeability and ethidium fluorescence results suggest that Ni underlayer might have direct and indirect effect on the bacteria inactivation process. Additionally, relatively low loss of the photocatalyst efficiency suggests that floating C-doped TiO2 photocatalyst with the Ni underlayer might be seen as the possible solution for the used photocatalyst recovery issue.

Modification of structured bio‑carbon derived from spongin-based scaffolds with nickel compounds to produce a functional catalyst for reduction and oxidation reactions: Potential for use in environmental protection

Three different 3D fibrous-like NiO/Ni(OH)₂/Ni‑carbonized spongin-based materials were prepared via a simple sorption-reduction method. Depending on the support used, the catalysts were composed of carbon, nickel oxide, nickel hydroxide and zero-valent nickel, with the surface content of the nickel-containing phase in the range 15.2-26.0 wt%. Catalytic studies showed promising activity in the oxidation of phenolic compounds in water and in the reduction of 4-nitrophenol. The oxidation efficiency depends on the substrate used and ranges from 80% for phenol at pH 2 to 99% for 4-chlorophenoxyacetic acid (4-CPA) and methylchlorophenoxypropionic acid (MCPP). In the reduction reaction, all catalysts exhibited superior activity, with rate constants in the range 0.648-1.022 min^-1. The work also includes a detailed investigation of reusability and kinetic studies.

NiCo2O4 nanoparticles inlaid on sulphur and nitrogen doped and co-doped rGO sheets as efficient electrocatalysts for the oxygen evolution and methanol oxidation reactions

The present work depicts the fabrication of NiCo₂O₄ decorated on rGO, and doped and co-doped rGO and its electrocatalytic activity towards the oxygen evolution reaction and methanol oxidation reaction. The NiCo₂O₄ catalyst with S-doped rGO outperformed the other catalysts, indicating that the sulphur atoms attached on rGO possess low oxophilicity and optimum free energy. This results in facile adsorption of the intermediate products formed during the OER and a rapid release of O₂ molecules. The same catalyst requires an overpotential of 1.51 V vs. RHE to attain the benchmark current density value of 10 mA cm^-2 and shows a Tafel slope of 57 mV dec^-1. It also reveals outstanding stability during its operation for 10 h with a minimum loss in potential. On the other hand, NiCo₂O₄/S,N-rGO reveals superior activity with high efficiency and stability in catalyzing methanol oxidation. The catalyst delivered a low onset potential of 0.12 V vs. Hg/HgO and high current density of 203.4 mA cm^-2 after addition of 0.5 M methanol, revealing the outstanding performance of the electrocatalyst.

Superior supercapacitor performance of Bi2S3 nanorod/reduced graphene oxide composites

The present work is focused on the synthesis of bismuth sulfide (Bi2S3) nanorod/reduced graphene oxide (RGO) composites via a one-step hydrothermal method using GO and bismuth nitrate in 5 : 1, 3 : 1 and 2 : 1 weight ratios and their characterization. The morphological studies revealed the formation of homogeneously dispersed Bi2S3 nanorods on RGO sheets along with occasional wrapping in the Bi2S3 nanorod/RGO (3 : 1) composite. XRD, FTIR, Raman and XPS studies suggested the incorporation of Bi2S3 in RGO sheets. The galvanostatic charge-discharge measurements showed that the Bi2S3 nanorod/RGO (3 : 1) composite exhibited the highest specific capacitance (1932 F g-1) at 1 A g-1 in the presence of 2 M aqueous KOH in a three-electrode cell. This is ascribed to the enhanced contact area between metal sulfide nanoparticles and RGO, increased conductivity and synergistic effect of Bi2S3 and RGO. The optimized Bi2S3 nanorod/RGO (3 : 1) composite also maintained an excellent cycling stability with ∼100% capacitance retention after 700 cycles. It is noted that the supercapacitor performance of the Bi2S3 nanorod/RGO (3 : 1) composite was better than group V and VI metal chalcogenides and their nanocomposites reported in several previous studies.

High potential and robust ternary LaFeO3/CdS/carbon quantum dots nanocomposite for photocatalytic H2 evolution under sunlight illumination

Exploitation of the novel, robust, and advanced photocatalytic systems with high efficiency is the present demand for clean, green, and sustainable energy production. Carbon quantum dots (CQDs) have attracted tremendous interest in efficient H₂ evolution from photocatalysis due to its remarkable visible-light harvesting and electron transport properties. Here, for the first time, a smart ternary nanocomposite comprises encapsulated CQDs with LaFeO₃ spherical nanoparticles and CdS nanorods is synthesized by a simple hydrothermal procedure for the efficient photocatalytic H₂ evolution under sunlight illumination. PXRD, FT-IR, FE-SEM, TEM, and XPS studies are performed to ensure the successful fabrication of ternary LaFeO₃/CdS/CQD nanocomposite. The efficient H₂ evolution rate (HER) of 25,302 μmol h^-1 g_cat^-1 is achieved for LaFeO₃/CdS/CQD nanocomposite, which is 602.4, 2.6, 29.8, 2.0 and 1.1 times higher than that of pristine LaFeO₃, pristine CdS, and composites such as LaFeO₃/CdS, LaFeO₃/CQD, and CdS/CQD. Photocurrent and lifetime PL studies reveal, encapsulation of CQDs with the LaFeO₃/CdS heterojunction can facilitate easy and efficient separation of photo-generated excitons. Altogether the fabrication of CQDs provides an ideal avenue for the development of high potential advanced photocatalytic systems for sustainable H₂ production with remarkable efficiencies.

Efficient Flexible All-Solid Supercapacitors with Direct Sputter-Grown Needle-Like Mn/MnOx@Graphite-Foil Electrodes and PPC-Embedded Ionic Electrolytes

Recent critical issues regarding next-generation energy storage systems concern the cost-effective production of lightweight, safe and flexible supercapacitors yielding high performances, such as high energy and power densities as well as a long cycle life. Thus, current research efforts are concentrated on the development of high-performance advance electrode materials with high capacitance and excellent stability and solid electrolytes that confer flexibility and safety features. In this work, emphasis is placed on the binder-free, needle-like nanostructured Mn/MnOx layers grown onto graphite-foil deposited by reactive sputtering technique and to the polymer gel embedded ionic electrolytes, which are to be employed as new flexible pseudocapacitive supercapacitor components. Microstructural, morphological and compositional analysis of the layers has been investigated by X-ray diffractometer (XRD), Field Emission Scanning Electron Microscope (FE-SEM) and X-ray photoelectron spectroscopy (XPS). A flexible lightweight symmetric pouch-cell solid-state supercapacitor device is fabricated by sandwiching a PPC-embedded ionic liquid ethyl-methylimidazolium bis (trifluoromethylsulfonyl) imide (EMIM)(TFSI) polymer gel electrolyte (PGE) between two Mn/MnOx@Graphite-foil electrodes and tested to exhibit promising supercapacitive behaviour with a wide stable electrochemical potential window (up to 2.2 V) and long-cycle stability. This pouch-cell supercapacitor device offers a maximum areal capacitance of 11.71 mF/cm2@ 0.03 mA/cm2 with maximum areal energy density (Ea) of 7.87 mWh/cm2 and areal power density (Pa) of 1099.64 mW/cm2, as well as low resistance, flexibility and good cycling stability. This supercapacitor device is also environmentally safe and could be operated under a relatively wide potential window without significant degradation of capacitance performance compared to other reported values. Overall, these rationally designed flexible symmetric all-solid-state supercapacitors signify a new promising and emerging candidate for component integrated storage of renewable energy harvested current.

Z-scheme binary 1D ZnWO4 nanorods decorated 2D NiFe2O4 nanoplates as photocatalysts for high efficiency photocatalytic degradation of toxic organic pollutants from wastewater

In this study, dimensionally coupled Z-scheme binary nanocomposites from two-dimensional (2D) NiFe₂O₄ nanoplates and one-dimensional (1D) ZnWO₄ nanorods are prepared for efficient degradation of an antibiotic tetracycline (TC) and organic dye rhodamine B (RhB) under solar illumination. NiFe₂O₄/ZnWO₄ nanocomposites were synthesized by a simple and ecological in-situ hydrothermal method without the use of surfactants. Structural and morphological studies revealed the formation of heterostructure and 1D ZnWO₄ nanorods were uniformly distributed over the surface of NiFe₂O₄ nanoplates. Light-harvesting capability was improved and optimized by loading with different amounts of ZnWO₄. Photoluminescence analysis demonstrated inhibited nature of the recombination of photo-excited charge carriers in the nanocomposites. Photocatalytic experiments revealed that the nanocomposite exhibited improved Z-scheme electron-transfer for the degradation of TC under solar illumination. In particular, NFZW-20 nanocomposite demonstrated superior photocatalytic degradation of TC of approximately 98% within 105 min. Furthermore, their photocatalytic performance was investigated by RhB dye under the solar irradiation to achieve 98% of degradation of RhB in 70 min. Improved photocatalytic activities are attributed to the Z-scheme electron-transfer mechanism, which could enhance the superior ability of light absorption and reduced recombination rate of the photogenerated charge carriers.

Facile hydrothermal synthesis of porous MgCo2O4 nanoflakes as an electrode material for high-performance asymmetric supercapacitors

In this work, porous MgCo₂O₄ nanoflakes (MgCo₂O₄ NFs) and MgCo₂O₄ nanocubes (MgCo₂O₄ NCs) have been successfully synthesized through a simple hydrothermal method combined with a post calcination process of the precursor in air. The morphology of the MgCo₂O₄ samples can be easily tuned by changing the hydrothermal temperature and reaction time, respectively. The porous MgCo₂O₄ NFs with an average pore size of 12.5 nm had a BET specific surface area up to 64.9 m² g^-1, which was larger than that of MgCo₂O₄ NCs (19.8 m² g^-1). The MgCo₂O₄ NFs delivered a specific capacitance of 734.1 F g^-1 at 1 A g^-1 and exhibited a considerable rate performance with 74.0% capacitance retention at 12 A g^-1. About 94.2% of its original capacitance could be retained after 5000 charge-discharge cycles at a constant current density of 5 A g^-1. An asymmetric supercapacitor (ASC) was assembled by using MgCo₂O₄ NFs as the positive electrode and AC as the negative electrode, and the ASC had a wide operation voltage of 1.7 V and a high energy density of 33.0 W h kg^-1 at a power density of 859.6 W kg^-1. Such outstanding electrochemical performances make the MgCo₂O₄ NFs a promising candidate for supercapacitor applications. In addition, the simple and scalable synthesis method can be extended to the preparation of other metal oxide-based electrode materials.

Electrochemical Performance of 2D-Hierarchical Sheet-Like ZnCo2O4 Microstructures for Supercapacitor Applications

With the rapid improvement of the global economy, the role of energy has become even more vital in the 21st century. In this regard, energy storage/conversion devices have become a major, worldwide research focus. In response to this, we have prepared two-dimensional (2D)-hierarchical sheet-like ZnCo2O4 microstructures for supercapacitor applications using a simple hydrothermal method. The 2D-hierarchical sheet-like morphologies with large surface area and smaller thickness enhanced the contact area of active material with the electrolyte, which increased the utilization rate. We investigated the electrochemical performance of sheet-like ZnCo2O4 microstructures while using Cyclic voltammetry (CV), Galvanostatic charge-discharge (GCD), and Electrochemical impedance spectroscopy (EIS) analysis. The electrochemical results demonstrated that the ZnCo2O4 electrode possesses 16.13 mF cm−2 of areal capacitance at 10 µA cm−2 of current density and outstanding cycling performance (170% of capacitance is retained after 1000 cycles at 500 µA cm−2). The high areal capacitance and outstanding cycling performance due to the unique sheet-like morphology of the ZnCo2O4 electrode makes it an excellent candidate for supercapacitor applications.

Electrochemically Stable Cobalt⁻Zinc Mixed Oxide/Hydroxide Hierarchical Porous Film Electrode for High-Performance Asymmetric Supercapacitor

Construction of electrochemically stable positive materials is still a key challenge to accomplish high rate performance and long cycling life of asymmetric supercapacitors (ASCs). Herein, a novel cobalt–zinc mixed oxide/hydroxide (CoZn-MOH) hierarchical porous film electrode was facilely fabricated based on a cobalt–zinc-based metal–organic framework for excellent utilization in ASC. The as-constructed hierarchical porous film supported on conductive Ni foam possesses a rough surface and abundant macropores and mesopores, which allow fast electron transport, better exposure of electrochemically active sites, and facile electrolyte access and ion diffusion. Owing to these structural merits in collaboration, the CoZn-MOH electrode prepared with a zinc feeding ratio up to 45% at 110 min of heating time (CoZn-MOH-45-110) exhibited a high specific capacitance of 380.4 F·g⁻¹, remarkable rate capability (83.6% retention after 20-fold current increase), and outstanding cycling performances (96.5% retention after 10,000 cycles), which exceed the performances of similar active electrodes. Moreover, an ASC based on this CoZn-MOH-45-110 electrode exhibited a high specific capacitance of 158.8 F·g⁻¹, an impressive energy density of 45.8 Wh·kg⁻¹, superior rate capability (83.1% retention after 50-fold current increase), and satisfactory cycling stability (87.9% capacitance retention after 12,000 cycles).

3D heterostructured cobalt oxide@layered double hydroxide core–shell networks on nickel foam for high-performance hybrid supercapacitor

3D heterostructured Co₃O₄@LDH networks were grown directly on nickel foam for the positive electrode of a high-performance hybrid supercapacitor.

Hierarchical MnCo2O4@NiMoO4 as free-standing core–shell nanowire arrays with synergistic effect for enhanced supercapacitor performance

A core–shell MnCo₂O₄@NiMoO₄ nanowire array prepared using a facile hydrothermal method showed extraordinary rate capability as a cathode for supercapacitors.

Facile synthesis of NiCo2S4/CNTs nanocomposites for high-performance supercapacitors

Herein, porous NiCo2S4/CNTs nanocomposites were synthesized via a simple hydrothermal method followed by the sulphurization process using different sulfide sources. By comparing two different sulfur sources, the samples using thioacetamide as sulfide source delivered more remarkable electrochemical performance with a high specific capacitance of 1765 F g-1 at 1 A g-1 and an admirable cycling stability with capacitance retention of 71.7% at a high current density of 10 A g-1 after 5000 cycles in 2 M KOH aqueous electrolyte. Furthermore, an asymmetric supercapacitor (ASC) device was successfully fabricated with the NiCo2S4/CNTs electrode as the positive electrode and graphene as the negative electrode. The device provided a maximum energy density of 29.44 W h kg-1 at a power density of 812 W kg-1. Even at a high power density of 8006 W kg-1, the energy density still reaches 16.68 W h kg-1. Moreover, the ASC presents 89.8% specific capacitance retention after 5000 cycles at 5 A g-1. These results reveal its great potential for supercapacitors in electrochemical energy storage field.

Porous Pt–NiOx nanostructures with ultrasmall building blocks and enhanced electrocatalytic activity for the ethanol oxidation reaction

A porous Pt–NiO_x nanomaterial was constructed by a simple strategy to achieve excellent ethanol oxidation catalyst performance.

Nanocrystalline LaOx/NiO composite as high performance electrodes for supercapacitors

Nanocrystalline LaO_x/NiO composite electrodes were synthesized via two types of facile cathodic electrodeposition methods onto nickel foam followed by thermal annealing without any binders.