Insights into emulsion synthesis of self-assembled suprastructures formed by Janus silica particles with -NH2/-SH surface groups

Spherical particles with tunable anisotropic structures enabled by multiple surface functionalities have garnered interest for their potential applications in adsorption technologies. The presence of diverse functional groups in the surface layer, exhibiting varying acidity and hydrophilicity, can lead to unique characteristics in terms of surface structure and behaviour. In this study, the particles were synthesised using a two-step approach involving surface functionalisation of previously synthesised SiO2 Stöber particles. This was achieved by employing 3-mercaptopropyltrimethoxysilane (MPTMS) and 3-aminopropyltrimethoxysilane (APTMS) in a toluene-in-water emulsion. The resulting particles were found to be nonporous, with a specific surface area of 8 m2 g-1. Their sizes were determined to be up to 350 nm through photon cross-correlation spectroscopy. Moreover, the particles exhibited a high net content of functional groups (both amino and mercapto) of 2 mmol g-1. The organisation of the particles during synthesis was observed through SEM images, providing insights into their structural characteristics. Additionally, the study of Eu(iii), Au(iii), and Ag(i) ions and fluorescein adsorption demonstrated varying interactions on the surface, highlighting the potential applications and versatility of these functionalised particles.

Molten salt mediated single-step synthesis of reusable nanostructured CaTiO3 for the removal and recovery of Sr2+: A potential adsorbent for the contaminated water bodies

The facile synthesis approach for the adsorbent preparation and recyclability during decontamination of radioactive pollutants is a significant concern in water treatment. The objective of this study is to, synthesis via solid-state reaction of the nanostructured CaTiO3 for the removal and recovery of strontium (Sr2+) from the various water sources. The influence of the adsorption-dependent parameters including, initial concentration, adsorbent dose, pH, contact time and co-existing ions interference were investigated. The prepared adsorbent was characterized by different analytical techniques like FT-IR, SEM with EDAX, TEM, TGA-DTG, Powder XRD and BET surface analysis. The kinetic models were also used, and according to the kinetic models, a pseudo-second-order kinetic model (R2 = 0.999) was better fitted to the adsorption of Sr2+ ions onto CaTiO3 rather than pseudo-first-order kinetics, which could properly represent the observed adsorption of Sr2+. For the isotherm study, the results are best fitted to the Langmuir isotherm model (R2 = 0.98) with a maximum adsorption capacity of 102.04 mg/g. The common ions (Na+, Mg2+, Ca2+, and K+) and Sr2+ having a concentration of 1:2, 1:3, and 1:4, where 82.8, 79.5, and 68.2 % removal was achieved of Sr2+ in each respective matrix. In addition, the adsorption and corresponding recovery and removal for the different Sr2+spiked matrices in deionized water, tap water, well water, lake water, and seawater were investigated with 97, 65.6, 76.5, 73.9 and 17.8 % removal respectively. Also, the CaTiO3 showed excellent recyclability with minimal loss even after 5 consecutive recyclability cycles and >90% removal of strontium achieved. Hence, prepared nanostructured CaTiO3 could be considered a promising adsorbent for the removal and recovery of Sr2+ions from contaminated water bodies.

Ultrasensitive detection of chloramphenicol in water using functionalized polymers with an aluminium organic framework

Metal-Organic Frameworks (MOFs) are extensively used as electrode material in various sensing applications due to their efficacious porous nature and tunable properties. However, pristine MOFs lack conductive attributes that hinder their wide usage in electrochemical applications. Electropolymerization of several aromatic monomers has been a widely used strategy for preparing conducting electrode materials for various sensing applications in the past decades. Herein, we report a similar approach by employing the electropolymerization method to create a functional polymer layer to enhance the sensitivity of an Aluminium Organic Framework (DUT-4) for the selective detection of Chloramphenicol (CAP) antibiotic in aqueous environment. The combined strategy using the conducting polymer layer with the porous Al MOF provides surpassing electrochemical performance for sensing CAP with regard to the very low detection limit (LOD = 39 nM) and exceptionally high sensitivity (11943 μA mM-1 cm-2). In addition, the fabricated sensor exhibited good selectivity, reproducibility and stability. The developed method was successfully evaluated in various real samples including lake water and river water for CAP detection with good recovery percentages even at lower concentrations.

Valorization of hazardous waste cooking oil for the production of eco-friendly biodiesel using a low-cost bifunctional catalyst

Biodiesel is considered the prospective substitute for non-renewable fossil fuel-derived sources of energy. However, the high costs of feedstocks and catalysts inhibit its large-scale industrial implementation. From this perspective, the utilization of waste as the source for both catalyst synthesis and feedstock for biodiesel is a rare attempt. Waste rice husk was explored as a precursor to prepare rice husk char (RHC). Sulfonated RHC was employed as a bifunctional catalyst for the simultaneous esterification and transesterification of highly acidic waste cooking oil (WCO) to produce biodiesel. The sulfonation process coupled with ultrasonic irradiation proved to be an efficient technique to induce high acid density in the sulfonated catalyst. The prepared catalyst possessed a sulfonic density and total acid density of 4.18 and 7.58 mmol/g, respectively, and a surface area of 144 m²/g. A parametric optimization was conducted for the conversion of WCO into biodiesel using the response surface methodology. An optimal biodiesel yield of 96% was obtained under the conditions of methanol to oil ratio (13:1), reaction time (50 min), catalyst loading (3.5 wt%), and ultrasonic amplitude (56%). The prepared catalyst showed higher stability up to five cycles with biodiesel yield greater than 80%.

A Critical Review of the Removal of Radionuclides from Wastewater Employing Activated Carbon as an Adsorbent

Radionuclide-contaminated water is carcinogenic and poses numerous severe health risks and environmental dangers. The activated carbon (AC)-based adsorption technique has great potential for treating radionuclide-contaminated water due to its simple design, high efficiency, wide pH range, quickness, low cost and environmental friendliness. This critical review first provides a brief overview of the concerned radionuclides with their associated health hazards as well as different removal techniques and their efficacy of removing them. Following this overview, this study summarizes the surface characteristics and adsorption capabilities of AC derived from different biomass precursors. It compares the adsorption performance of AC to other adsorbents, such as zeolite, graphene, carbon nano-tubes and metal-organic frameworks. Furthermore, this study highlights the different factors that influence the physical characteristics of AC and adsorption capacity, including contact time, solution pH, initial concentration of radionuclides, the initial dosage of the adsorbent, and adsorption temperature. The theoretical models of adsorption isotherm and kinetics, along with their fitting parameter values for AC/radionuclide pairs, are also reviewed. Finally, the modification procedures of pristine AC, factors determining AC characteristics and the impact of modifying agents on the adsorption ability of AC are elucidated in this study; therefore, further research and development can be promoted for designing a highly efficient and practical adsorption-based radionuclide removal system.

Selective strontium adsorption using synthesized sodium titanate in aqueous solution

Amorphous sodium titanates were synthesized using a mid-temperature sol–gel method for evaluation as selective adsorbents of strontium in the presence of cesium or metal cations (Al³⁺, Mg²⁺, Ca²⁺, and Mn²⁺) from aqueous solution. Synthesized sodium titanate showed high adsorption capacity and selectivity for strontium. The maximum adsorption capacity of strontium by sodium titanate was 193.93 mg g⁻¹ in aqueous solution containing an initial concentration of 5 mM (438.60 mg L⁻¹) strontium and 5 mM (666.67 mg L⁻¹) cesium, and this sodium titanate removed 99.9% of the strontium and 40.67% of cesium from an aqueous solution that had an initial concentration of 1.14 mM (100 mg L⁻¹) strontium and 0.75 mM (100 mg L⁻¹) cesium. Strontium adsorption by synthesized sodium titanate followed pseudo-second-order kinetics and a generalized Langmuir isotherm model, and reached an adsorption equilibrium within 1 h with high adsorption capacity at equilibrium. Adsorbed strontium onto synthesized sodium titanate showed the behavior of forming a strontium titanate structure with a titanate frame via surface precipitation.

Amorphous sodium titanates were synthesized using a mid-temperature sol–gel method for evaluation as selective adsorbents of strontium in the presence of cesium or metal cations (Al³⁺, Mg²⁺, Ca²⁺, and Mn²⁺) from aqueous solution.

Fabrication of Pt-Loaded Catalysts Supported on the Functionalized Pyrolytic Activated Carbon Derived from Waste Tires for the High Performance Dehydrogenation of Methylcyclohexane and Hydrogen Production

The pyrolytic activated carbon derived from waste tires (PTC) was functionalized to fabricate the high performance of Pt-based catalysts in the dehydrogenation of methylcyclohexane and hydrogen production. Structural characterizations evidenced that the modification partially influenced the surface area, the pore structure, and the oxygen-containing functional groups of the supports. The techniques of CO pulse, transmission electron microscopy, and hydrogen temperature-programmed reduction were utilized to investigate the dispersion degrees and particle sizes of the active component Pt, and its interaction with the various functionalized supports, respectively. The results manifested that Pt particles loaded on the functionalized PTC-S had the largest dispersion degree and the smallest size among those loaded on PTC and other functionalized PTC (i.e., PTC-K and PTC-NH). Finally, the Pt-based catalysts were successfully applied in the dehydrogenation reaction of methylcyclohexane to yield hydrogen. The results revealed that the Pt catalyst over the functional PTC-S support exhibited a more excellent conversion of methylcyclohexane (84.3%) and a higher hydrogen evolution rate (991.5 mmol/gPt/min) than the other resulting Pt-based catalysts.

Electrosorption of cadmium ions in aqueous solutions using a copper-gallate metal-organic framework

Recently, there is a recognized need for green technologies for the effective decontamination of toxic heavy metal ions in wastewater. This study demonstrates the electrochemically assisted uptake and release of cadmium ions (Cd²⁺) using a redox-active Cu-based metal-organic framework (MOF) electrode. Copper gallate (CuGA), which was synthesized in an aqueous solution, is a water-stable and cost-effective MOF adsorbent in which naturally abundant gallic acid is used as a linker. This work utilized copper within the CuGA structure as a redox center to attract Cd²⁺ by means of Cu²⁺/Cu⁺ reduction, exhibiting rapid uptake kinetics and a much higher capacity (>60 mg g^-1) compared to the case without electrochemical assistance (~15 mg g^-1). In addition, by applying an opposite overpotential to induce the re-oxidation of copper, the facile recovery of Cd²⁺ and the regeneration of the electrode were possible without regenerants. Physicochemical characterizations including XPS were conducted to investigate the chemical oxidation states and stability of the electrode after the effective electrosorption-regeneration process. This work presents the feasibility of a Cu-based MOF electrode as a reusable platform for the efficient removal of Cd²⁺, supporting the continued discovery and development of new Faradaic electrodes for electrochemical wastewater treatments.

Sunlight promoted removal of toxic hexavalent chromium by cellulose derived photoactive carbon dots

A scalable synthetic procedure for fabricating photoactive carbon dots (CD) from microcrystalline cellulose (MCC) is presented. The MCC was transformed into a photoactive nanosized CD by a one-step acid-assisted thermal-carbonization (~90 °C for 30 min). The efficiency of the obtained CD was determined by photo-removal of toxic hexavalent chromium (Cr(VI)) ions from wastewater. CD obtained from cellulose completely removed 20 ppm of Cr(VI) wastewater within ∼120 min under sunlight illumination. No Cr(VI) removal was observed in dark conditions and with control cellulose material as reference samples. The Cr(VI) removal follows pseudo-first-order kinetics along with a half-life of ∼26 min. Furthermore, the Cr(VI) removal from wastewater was supported via cyclic voltammetry analysis. Using a low-cost, naturally available cellulose material and sulfuric acid, the world's most-used chemical, creates techno-economic prerequisites for a scalable process of photoactive carbon dots.

Covalent immobilization of bromocresol purple on cellulose nanocrystals for use in pH-responsive indicator films

This study developed pH-indicator films by combining esterified cellulose nanocrystals (e-CNCs) with activated bromocresol purple (a-BCP) via covalent bonding for pH-sensitive color-changing applications. The e-CNC/a-BCP particles were incorporated into cellulose acetate polymer to prepare pH-sensitive color changing films. Binding of a-BCP to e-CNCs was proven by attenuated total reflection infrared (ATR-IR) spectroscopy and X-ray photoelectron spectroscopy (XPS). Colorimetric analysis showed that films containing 10% or 15% e-CNC/a-BCP particles had critical color changes either at pH 4-5, or pH 7-8. The films with 10% e-CNC/a-BCP particles also revealed excellent leaching resistance under acidic conditions. Color changes were reversible between pH 2 and 10. These pH-indicator films had visible color changes in response to pH variations, color reversibility, leaching resistance, and sufficient rigidity even though mechanical properties decreased as the e-CNC/a-BCP content increased from 0% to 15%.

Assessing of cesium removal from wastewater using functionalized wood cellulosic adsorbent

Sustainable materials are urgently desired for treatment of radioactive cesium (Cs) contaminated water to safe-guard the public health. Apart from the synthetic ligand-based materials, the Mangrove charcoal modified adsorbent was fabricated for assessing of Cs removal from waste sample. The raw charcoal was oxidized using nitrification approach and diverse oxygen containing carboxyl, carbonyl and hydroxyl functional groups were introduced. After modification, the adsorbent characteristics were drastically changed as compared to the charcoal during the measurement of FTIR, N₂ adsorption-desorption isotherms and SEM micrographs. The data clarified that charcoal modified adsorbent was exhibited high Cs transport through the inner surface of the adsorbent based on bonding ability. The adsorbent was shown comparatively slow kinetics to Cs ion; however, the adsorption capacity was high as 133.54 mg/g, which was higher than the crown ether based conjugate materials. The adsorption data were followed to the Langmuir adsorption isotherms and the monolayer coverage was possible due to the data presentation. The presence of high amount of Na and K were slightly interfered to the Cs adsorption by the charcoal modified adsorbent, however; the Na and K concentration was 350-600 folds higher than the Cs concentration. Then the proposed adsorbent was selective to Cs for the potential real radioactive Cs contaminated water. The volume reduction was established rather than desorption and reuses advantages. More than 99% volume reduction was measured by burning of Cs adsorbed adsorbent at 500 °C for ensuring the safe storage and disposal of used adsorbent. Therefore, the charcoal modified adsorbent may open the new door to treat the Cs containing wastewater.

Bio-Inspired Preparation of Clay-Hexacyanoferrate Composite Hydrogels as Super Adsorbents for Cs. ACS APPLIED MATERIALS & INTERFACES 2020;12:33173-33185. [PMID: 32531151 DOI: 10.1021/acsami.0c06598]

A facile and low-cost fabrication route, inspired by the adhesive proteins secreted by mussels, has been developed to prepare a clay-based composite hydrogel (DHG(Cu)) containing hexacyanoferrate (HCF) nanoparticles for the selective removal of Cs⁺ from contaminated water. Initially, montmorillonite was exfoliated prior to coating with a thin layer of polydopamine (PDOPA) via the self-polymerization of dopamine. Mixing the composite (D-clay) with the HCF precursor, followed by the addition of copper ions, led to the self-assembly of the polymer-coated exfoliated clay nanosheets into a three-dimensional network and in situ growth of KCuHCF nanoparticles embedded within the gel structure. Analytical characterization verified the fabrication route and KCuHCF immobilization by a copper-ligand complexation. Rheology testing revealed the composite hydrogel to be elastic under low strain and exhibited reversible, self-healing behavior following high strain deformation, providing a good retention of KCuHCF nanoparticles in the membrane. The adsorbent DHG(Cu) showed a superior Cs⁺ adsorption capacity (∼173 mg/g), with the performance maintained over a wide pH range, and an excellent selectivity for Cs⁺ when dispersed in seawater at low concentrations of 0.2 ppm. On the basis of its excellent mechanico-chemical properties, the fabricated hydrogel was tested as a membrane in column filtration, showing excellent removal of Cs⁺ from Milli-Q water and seawater, with the performance only limited by the fluid residence time. For comparison, the study also considered other composite hydrogels, which were fabricated as intermediates of DHG(Cu) or fabricated with Fe³⁺ as the cross-linker and reactant for HCF nanoparticle synthesis.

Effective removal of cesium from wastewater via adsorptive filtration with potassium copper hexacyanoferrate-immobilized and polyethyleneimine-grafted graphene oxide

As an attractive alternative to radioactive cesium removal, we introduced an adsorptive filtration method using a composite membrane consisting of potassium copper hexacyanoferrate (KCuHCF) and graphene-based support. Polyethyleneimine-grafted reduced graphene oxide (PEI-rGO), used as an immobilizing matrix, was effective not only in distributing KCuHCF inside the composite with the aid of abundant amino-functionality, but also in achieving high water flux by increasing the interlayer spacing of the laminar membrane structure. Due to the rapid and selective cesium adsorption properties of KCuHCF, the fabricated membrane was found to be effective in achieving complete removal of cesium ions under a high flux (over 500 L m^-2 h^-1), which is difficult in a conventional membrane utilizing the molecular sieving effect. This approach offers strong potential in the field of elimination of radionuclides that require rapid and complete decontamination.

Efficient electron-mediated electrochemical biosensor of gold wire for the rapid detection of C-reactive protein: A predictive strategy for heart failure

C-reactive protein (CRP) is considered a promising biomarker for the rapid and high-throughput real-time monitoring of cardiovascular disease and inflammation in unprocessed clinical samples. Implementation of this monitoring would enable various transformative biomedical applications. We have fabricated a highly specific sensor chip to detect CRP with a detection limit of 2.25 fg/mL. The protein was immobilized on top of a gold (Au) wire/polycarbonate (PC) substrate using 1-ethyl-3-(3-dimethylamino-propyl) carbodiimide hydrochloride/N-hydroxy succinimide-activated 3-mercaptoproponic acid (MPA) as a self-assembled monolayer agent and bovine serum albumin (BSA) as a blocking agent. In contrast to the bare PC substrate, the CRP/BSA/anti-CRP/MPA/Au substrate exhibited a considerably high electrochemical signal toward CRP. The influence of the experimental parameters on CRP detection was assessed via various analysis methods, and these parameters were then optimized. The linear dynamic range of the CRP was 5-220 fg/mL for voltammetric and impedance analysis. Morever, the strategy exhibited high selectivity against various potential interfering species and was capable of directly probing trace amounts of the target CRP in human serum with excellent selectivity. The analytical assay based on the CRP/BSA/anti-CRP/MPA/Au substrate could be exploited as a potentially useful tool for detecting CRP in clinical samples.

Investigation of MnO2 nanoparticles-anchored 3D-graphene foam composites (3DGF-MnO2) as an adsorbent for strontium using the central composite design (CCD) method

Strontium-90 is one of the dangerous fission products generated during electricity production in nuclear reactors and the separation of this radionuclide from contaminated water is an important step in safeguarding human health and minimizing the impact on the environment.

Amino-functionalized magnetic chitosan beads to enhance immobilization of potassium copper hexacyanoferrate for selective Cs+ removal and facile recovery

Potassium copper hexacyanoferrate (KCuHCF)-incorporated magnetic chitosan beads (HMC) were synthesized for both selective Cs⁺ removal in aqueous solutions and facile recovery of the spent adsorbent. To disperse and immobilize large amounts of the KCuHCF, methyl acrylate and diethylenetriamine were sequentially grafted onto the one-step synthesized magnetic chitosan beads. The additional introduction of amino functionality led to the enriched Cu²⁺ ions on the bead surface to incorporate KCuHCF into the grafting matrix. Consequently, the HMC exhibited a high Cs⁺ capacity calculated to be 136.47 mg g⁻¹ from the Langmuir model, and the equilibrium was established within 4 h. Moreover, the HMC exhibited excellent stability in a wide pH range from 4 to 11 and an outstanding Cs⁺ selectivity (>97%) in seawater (1.11 mg L⁻¹ Cs⁺). From a practical point of view, the HMC was stable during five successive adsorption cycles and easily recovered by magnets, enabling continuous operation to decontaminate a large volume of wastewater.

The magnetic chitosan beads were amino-functionalized by grafting and showed an outstanding removal performance for radioactive Cs⁺.