Polyvinyl chloride in consumer and environmental plastics, with a particular focus on metal-based additives

Environmental-friendly extraction of di(2-ethylhexyl) phthalate from poly(vinyl chloride) using liquefied dimethyl ether

Poly(vinyl chloride) (PVC) is one of the most widely used plastics. However, a major challenge in recycling PVC is that there is no economical method to separate and remove its toxic phthalate plasticizers. This research made a breakthrough by extracting PVC with liquefied dimethyl ether (DME) and successfully separating the plasticizer components. Nearly all (97.1 %) of the di(2-ethylhexyl) phthalate plasticizer was extracted within 30 min by passing liquefied DME (285 g) through PVC at 25 °C. The compatibility of PVC with organic solvents, including liquefied DME, was derived theoretically from their Hansen solubility parameters (HSP), and actual dissolution experiments were conducted to determine the optimal PVC solvents. A liquefied DME mixture was used to dissolve PVC, and the extract was diluted with ethanol to precipitate the dissolved PVC. We demonstrated that liquefied DME is a promising method for producing high quality recycled products and that the process retains the fundamental properties of plasticizers and PVC without inducing degradation or depolymerization. Because of its low boiling point, DME can be easily separated from the solute after extraction, allowing for efficient reuse of the solvent, extracted plasticizer, and PVC. DME does not require heat and produces little harmful wastewater, which significantly reduces the energy consumption of the plasticizer additive separation process.

Impacts associated with the plastic polymers polycarbonate, polystyrene, polyvinyl chloride, and polybutadiene across their life cycle: A review

Polymers are the main building blocks of plastic, with the annual global production volume of fossil carbon-based polymers reaching over 457 million metric tons in 2019 and this figure is anticipated to triple by 2060. There is potential for environmental harm and adverse human health impacts associated with plastic, its constituent polymers and the chemicals therein, at all stages of the plastic life cycle, from extraction of raw materials, production and manufacturing, consumption, through to ultimate disposal and waste management. While there have been considerable research and policy efforts in identifying and mitigating the impacts associated with problematic plastic products such as single-use plastics and hazardous chemicals in plastics, with national and/or international regulations to phase out their use, plastic polymers are often overlooked. In this review, the polymer dimension of the current knowledge on environmental release, human exposure and health impacts of plastic is discussed across the plastic life cycle, including chemicals used in production and additives commonly used to achieve the properties needed for applications for which the polymers are generally used. This review focuses on polycarbonate, polystyrene, polyvinyl chloride, and polybutadiene, four common plastic polymers made from the hazardous monomers, bisphenol, styrene, vinyl chloride and 1,3-butadiene, respectively. Potential alternative polymers, chemicals, and products are considered. Our findings emphasise the need for a whole system approach to be undertaken for effective regulation of plastics whereby the impacts of plastics are assessed with respect to their constituent polymers, chemicals, and applications and across their entire life cycle.

Legacy and Emerging Plasticizers and Stabilizers in PVC Floorings and Implications for Recycling

Hazardous chemicals in building and construction plastics can lead to health risks due to indoor exposure and may contaminate recycled materials. We systematically sampled new polyvinyl chloride floorings on the Swiss market (n = 151). We performed elemental analysis by X-ray fluorescence, targeted and suspect gas chromatography-mass spectrometry analysis of ortho-phthalates and alternative plasticizers, and bioassay tests for cytotoxicity and oxidative stress, and endocrine, mutagenic, and genotoxic activities (for selected samples). Surprisingly, 16% of the samples contained regulated chemicals above 0.1 wt %, mainly lead and bis(2-ethylhexyl) phthalate (DEHP). Their presence is likely related to the use of recycled PVC in new flooring, highlighting that uncontrolled recycling can delay the phase-out of hazardous chemicals. Besides DEHP, 29% of the samples contained other ortho-phthalates (mainly diisononyl and diisodecyl phthalates, DiNP and DiDP) above 0.1 wt %, and 17% of the samples indicated a potential to cause biological effects. Considering some overlap between these groups, they together make up an additional 35% of the samples of potential concern. Moreover, both suspect screening and bioassay results indicate the presence of additional potentially hazardous substances. Overall, our study highlights the urgent need to accelerate the phase-out of hazardous substances, increase the transparency of chemical compositions in plastics to protect human and ecosystem health, and enable the transition to a safe and sustainable circular economy.

Chemical characteristics of artificial plastic plants and the presence of hazardous elements from the recycling of electrical and electronic waste

Because of their convenience, the demand for decorative plastic plants has been increasing over recent years. However, no information exists on the origin or nature of the polymers employed or the type of additives used in order to understand potential environmental impacts and inform safe and sustainable disposal or recycling practices. In this study, 203 parts or offcuts from 175 plastic plants acquired from European shops and venues have been analysed by X-ray fluorescence spectrometry to determine elemental content, while a selection has been analysed by infrared spectrometry to establish polymer type. The (usually green) moulded components (n = 159) were commonly constructed of polyethylene or polypropylene, while leaves and colourful petals (n = 40) were generally made of polyethylene terephthalate fabric that had been glued to the moulded component. However, both components also exhibited evidence of being coated with a resin or adhesive for support, protection or appearance. Barium, Fe, Ti and Zn-based additives were commonly encountered but more important from an environmental and health perspective were variable concentrations of potentially hazardous elements in the moulded parts: namely, Br (6.1 to 108,000 mg kg-1; n = 78), Pb (7.6 to 17,400 mg kg-1; n = 53) and Sb (58.6 to 70,800 mg kg-1; n = 17). These observations suggest that many of the moulded components are derived from recyclates that are contaminated by waste electronic and electrical plastic, introducing brominated flame retardants, the flame retardant synergist, Sb2O3, and Pb into the final product. There are no standards for these chemicals in plastic plants, but regulations for electronic plastic, toy safety and packaging are frequently exceeded or potentially exceeded. Widespread contamination of plastic plants may impose constraints on their recycling and disposal.

Global perspective on microplastics in landfill leachate; Occurrence, abundance, characteristics, and environmental impact

Plastic wastes deposited in landfills eventually break down and degrade into microplastics by physical, chemical, and biological forces. Though microplastics in leachate pose significant threats to the environment, the leachate generated from landfills has not received much attention as a possible source of environmental microplastics. A descriptive and systematic investigationof the global distribution of microplastics in landfill leachate does not exist to date. Therefore, this attempt is to provide a concise scientometric review of the studies on the presence of microplastics in landfill leachate. The present review revealed that the global trend in research on microplastics in leachate has increased exponentially after 2018 and China is the leading country. Different geographical regions have reported different microplastic abundances with the highest of 291.0 ± 91.0 items/L from a landfill in Shanghai. The use of novel sampling techniques to detect small microplastics (20-100 µm) has led to the high abundance of microplastics in landfill leachate in Shanghai. Due to its widespread usage, polyethylene is the most typically encountered polymer type in landfill leachate around the world. However, it is quite challengingto compare the results among studies due to the use of different size categories and extraction techniques. The removal of microplastics by the current leachate treatment facilities is still mostly unexplored, thus it is crucial to develop novel technologies to treat the microplastics in landfill leachate. Further investigations on the transport of microplastics in landfill leachate are urgently required to have a better understanding of potential human exposure and health implications.

Effects of UV radiation on natural and synthetic materials

The deleterious effects of solar ultraviolet (UV) radiation on construction materials, especially wood and plastics, and the consequent impacts on their useful lifetimes, are well documented in scientific literature. Any future increase in solar UV radiation and ambient temperature due to climate change will therefore shorten service lifetimes of materials, which will require higher levels of stabilisation or other interventions to maintain their lifetimes at the present levels. The implementation of the Montreal Protocol and its amendments on substances that deplete the ozone layer, controls the solar UV-B radiation received on Earth. This current quadrennial assessment provides a comprehensive update on the deleterious effects of solar UV radiation on the durability of natural and synthetic materials, as well as recent innovations in better stabilising of materials against solar UV radiation-induced damage. Pertinent emerging technologies for wood and plastics used in construction, composite materials used in construction, textile fibres, comfort fabric, and photovoltaic materials, are addressed in detail. Also addressed are the trends in technology designed to increase sustainability via replacing toxic, unsustainable, legacy additives with 'greener' benign substitutes that may indirectly affect the UV stability of the redesigned materials. An emerging class of efficient photostabilisers are the nanoscale particles that include oxide fillers and nanocarbons used in high-performance composites, which provide good UV stability to materials. They also allow the design of UV-shielding fabric materials with impressive UV protection factors. An emerging environmental issue related to the photodegradation of plastics is the generation of ubiquitous micro-scale particles from plastic litter exposed to solar UV radiation.

Incorporation of ultrathin porous metal-free graphite carbon nitride nanosheets in polyvinyl chloride for efficient photodegradation

Solid-phase photocatalytic degradation of waste plastics is one of the promising approaches to solve the "white pollution" problem. In this work, a low cost, metal-free, environmentally friendly organic photocatalyst, graphite carbon nitride (g-C₃N₄), was used for the first time to successfully enhance the photodegradation of polyvinyl chloride (PVC) under simulated sunlight from its visible light photocatalytic capability, while its organic nature and abundant surface functional groups were beneficial for its good dispersion in plastics. It was found that the ultrathin porous g-C₃N₄ nanosheet synthesized from urea (the UCN sample) had much stronger photodegradation effect in PVC/g-C₃N₄ composite films than its thick block counterpart synthesized with melamine (the MCN sample) due to its larger specific surface area, higher pore volume, and enhanced photogenerated charge carrier separation. With the incorporation of only 1 wt% UCN sample into PVC, its mechanical properties were largely enhanced with the tensile strength increase of ∼ 45% and the elongation at break increase of ∼ 72%, and its weight loss increased ∼ 58% after 120 h irradiation in the weather resistance test chamber. ^·O₂^- and h⁺ produced by the UCN sample were found as the main active species in the photocatalytic degradation of PVC to dechlorinate PVC and decompose its long-chain molecules into short-chain small molecules until its final degradation into CO₂ and H₂O under ideal conditions.

Chemical Structures, Properties, and Applications of Selected Crude Oil-Based and Bio-Based Polymers

The growing perspective of running out of crude oil followed by increasing prices for all crude oil-based materials, e.g., crude oil-based polymers, which have a huge number of practical applications but are usually neither biodegradable nor environmentally friendly, has resulted in searching for their substitutes-namely, bio-based polymers. Currently, both these types of polymers are used in practice worldwide. Owing to the advantages and disadvantages occurring among plastics with different origin, in this current review data on selected popular crude oil-based and bio-based polymers has been collected in order to compare their practical applications resulting from their composition, chemical structure, and related physical and chemical properties. The main goal is to compare polymers in pairs, which have the same or similar practical applications, regardless of different origin and composition. It has been proven that many crude oil-based polymers can be effectively replaced by bio-based polymers without significant loss of properties that ensure practical applications. Additionally, biopolymers have higher potential than crude oil-based polymers in many modern applications. It is concluded that the future of polymers will belong to bio-based rather than crude oil-based polymers.

Human exposure to microplastics from urban decentralized pay-to-fetch drinking-water refill kiosks

Microplastics in the human diet have become a worldwide concern. To date, microplastics in urban drinking water supplies, such as decentralized drinking-water refill kiosks, have not been studied and are a pressing concern since they are so closely tied to human life and have a significant influence on health. This study evaluated the occurrence and characteristics of microplastics in 63 drinking water samples collected from decentralized refill kiosks in the Mexico City metropolitan area. All of the sampled drinking water contained microplastics in concentrations ranging from 11 to 860 microplastics L^-1. The detected microplastics were mostly fiber (65 %), followed by fragment (28 %), and film (7 %). They were mainly composed of polyethylene terephthalate, polyamides, vinyl polymers, polyacetal, and cellophane in sizes ranging from 20 μm to 5 mm, with 75 % of them accounting for sizes <300 μm. SEM-EDX analysis revealed weathered microplastics, biota adherence, and the presence of inorganic elements on the surface of microplastics. We estimate that Mexico City residents inadvertently ingest 42 microplastics L^-1, with an annual exposure of around 1.47 × 10⁴ microplastics per adult and 6.73 × 10³ microplastics per child. Therefore, future research is needed to strengthen drinking water refill kiosk guidelines and standards for better microplastic management. This study serves as a wake-up call to many developing countries that use similar urban water systems, drawing their attention to global microplastic contamination of drinking water.

Plastic leachates impair picophytoplankton and dramatically reshape the marine microbiome

BACKGROUND

Each year, approximately 9.5 million metric tons of plastic waste enter the ocean with the potential to adversely impact all trophic levels. Until now, our understanding of the impact of plastic pollution on marine microorganisms has been largely restricted to the microbial assemblages that colonize plastic particles. However, plastic debris also leaches considerable amounts of chemical additives into the water, and this has the potential to impact key groups of planktonic marine microbes, not just those organisms attached to plastic surfaces.

RESULTS

To investigate this, we explored the population and genetic level responses of a marine microbial community following exposure to leachate from a common plastic (polyvinyl chloride) or zinc, a specific plastic additive. Both the full mix of substances leached from polyvinyl chloride (PVC) and zinc alone had profound impacts on the taxonomic and functional diversity of our natural planktonic community. Microbial primary producers, both prokaryotic and eukaryotic, which comprise the base of the marine food web, were strongly impaired by exposure to plastic leachates, showing significant declines in photosynthetic efficiency, diversity, and abundance. Key heterotrophic taxa, such as SAR11, which are the most abundant planktonic organisms in the ocean, also exhibited significant declines in relative abundance when exposed to higher levels of PVC leachate. In contrast, many copiotrophic bacteria, including members of the Alteromonadales, dramatically increased in relative abundance under both exposure treatments. Moreover, functional gene and genome analyses, derived from metagenomes, revealed that PVC leachate exposure selects for fast-adapting, motile organisms, along with enrichment in genes usually associated with pathogenicity and an increased capacity to metabolize organic compounds leached from PVC.

CONCLUSIONS

This study shows that substances leached from plastics can restructure marine microbial communities with the potential for significant impacts on trophodynamics and biogeochemical cycling. These findings substantially expand our understanding of the ways by which plastic pollution impact life in our oceans, knowledge which is particularly important given that the burden of plastic pollution in the marine environment is predicted to continue to rise. Video Abstract.

Spatio-temporal patterns of occurrence of microplastics in the freshwater fish Gambusia affinis from the Brantas River, Indonesia

The first investigation of microplastics in G. affinis from the Brantas River was carried out in this study. Microplastics were found at higher concentrations in gambusia fish captured downstream (209.18 ± 48.85 particles/gram) than upstream (24.44 ± 0.14 particles/gram). Microplastic particle concentrations in G. affinis have a positive linear relationship with fish length. The fiber was the most prominent shape at Sites 1 and 2, whereas the fragment was dominant at Sites 3 and 4. With a value of 45-48%, black dominates the entire site, followed by blue (29-38%), transparent colors (7-11%), red (2-4%), purple (1-3%), and other colors (5-7%). Microplastics measuring <0.1 mm are commonly found in fish bodies. Cyclohexylmethyl octyl ester (phthalic acid) is the most abundant component found in microplastics, accounting for 30.11% of the total. This study provides evidence that G. affinis can be used to monitor the presence of microplastic pollution in the Brantas River but further studies are needed regarding the effects of microplastics and their health hazards on fish.

Modification on antibacterial activity of PVC/PVDF blend filled with CuO NPs using laser ablation technique

Nanocomposite of polyvinyl chloride (PVC)/polyvinylidene fluoride (PVDF) have been in situ synthesized. Copper oxide nanoparticles (CuONPs) have been prepared via using the laser ablation technique. Nanoparticles were added to the blend. The properties of the blend were studied before and after adding CuONPs. These properties were characterized by different techniques. Antimicrobial activity of the prepared nanocomposite film was investigated. FTIR data show vibrational spectral bands and the shift of the bands is related to the interaction and the complexation that occurs between blend and nanoparticles. Structural properties and crystallinity of the samples were investigated using XRD diffraction. XRD results illustrated the effect of CuONPs at two new peaks 2θ = 26.25º and 38.41º. These results confirmed the interaction CuO NPs and PVDF/PVC matrix. UV–Visible analyses confirmed the existing of copper oxide nanoparticles and were also used for determining the optical absorption edge. The absorption edges have been obtained at 430–520 nm for all of the doping films. The obtained values for indirect and direct bandgaps were reduced by raising the nanoparticles because of the presence of charge transfer between PVC/PVDF and CuONPs. SEM images illustrateed the presence of CuONPs on the surface of the blend and the morphology changes which occurred to the blend. The antibacterial activity for the nanocomposite proved the antimicrobial effect of copper oxide nanoparticles. The prepared PVC/PVDF/CuONPs are potentially suggesting to be applied for biomedical applications.

Natural Fiber-Reinforced Thermoplastic ENR/PVC Composites as Potential Membrane Technology in Industrial Wastewater Treatment: A Review

Membrane separation processes are prevalent in industrial wastewater treatment because they are more effective than conventional methods at addressing global water issues. Consequently, the ideal membranes with high mechanical strength, thermal characteristics, flux, permeability, porosity, and solute removal capacity must be prepared to aid in the separation process for wastewater treatment. Rubber-based membranes have shown the potential for high mechanical properties in water separation processes to date. In addition, the excellent sustainable practice of natural fibers has attracted great attention from industrial players and researchers for the exploitation of polymer composite membranes to improve the balance between the environment and social and economic concerns. The incorporation of natural fiber in thermoplastic elastomer (TPE) as filler and pore former agent enhances the mechanical properties, and high separation efficiency characteristics of membrane composites are discussed. Furthermore, recent advancements in the fabrication technique of porous membranes affected the membrane's structure, and the performance of wastewater treatment applications is reviewed.

Deep insight into the Sb(III) and Sb(V) removal mechanism by Fe-Cu-chitosan material

Currently, alleviating antimony (Sb) contamination in aqueous solutions is crucial for restoring and recovering ecological and environmental health. Due to its toxicity, bioaccumulation and mobile characteristics, developing an efficient technique for antimony decontamination is imperative. Herein, we prepared a Fe-Cu-chitosan (FCC) composite by a one-step coprecipitation method, in which nanoscale Fe/Cu acts as the active sites and the whole structure is exhibited as porous microscale particles. A Fe/Cu proportion of 2/1 (FCC-2/1) was determined to be the optimum proportion for antimony adsorption, specifically 34.5 mg g^-1 for Sb(III) and 26.8 mg g^-1 for Sb(V) (initial concentration: 5.0 mg L^-1). Spectral characterization, batch experiments and density functional theory (DFT) simulations were applied to determine the adsorption mechanism, in which surface hydroxyls (-OH) were responsible for antimony complexion and Fe-Cu coupling was a major contributor to adsorption enhancement. According to kinetic analysis, Cu provided an electrostatic attraction during the adsorption process, which facilitated the transportation of antimony molecules to the material interface. In the meantime, the FCC electronic structure was modified due to the optimization of the Fe-Cu interface coupling. Based on the Mullikan net charge, the intrinsic Fe-O-Cu bond might favor interfacial electronic redistribution. When the antimony molecule contacted the adsorption interface, the electrons transferred swiftly as Fe/Cu 3d and O 2p orbital hybridization occurred, thus inducing a stabilizing effect. This work may offer a new perspective for binary oxide construction and its adsorption mechanism analysis.

Modifications of Polymers through the Addition of Ultraviolet Absorbers to Reduce the Aging Effect of Accelerated and Natural Irradiation

The photooxidative degradation process of plastics caused by ultraviolet irradiation leads to bond breaking, crosslinking, the elimination of volatiles, formation of free radicals, and decreases in weight and molecular weight. Photodegradation deteriorates both the mechanical and physical properties of plastics and affects their predicted life use, in particular for applications in harsh environments. Plastics have many benefits, while on the other hand, they have numerous disadvantages, such as photodegradation and photooxidation in harsh environments and the release of toxic substances due to the leaching of some components, which have a negative effect on living organisms. Therefore, attention is paid to the design and use of safe, plastic, ultraviolet stabilizers that do not pose a danger to the environment if released. Plastic ultraviolet photostabilizers act as efficient light screeners (absorbers or pigments), excited-state deactivators (quenchers), hydroperoxide decomposers, and radical scavengers. Ultraviolet absorbers are cheap to produce, can be used in low concentrations, mix well with polymers to produce a homogenous matrix, and do not alter the color of polymers. Recently, polyphosphates, Schiff bases, and organometallic complexes were synthesized and used as potential ultraviolet absorbers for polymeric materials. They reduced the damage caused by accelerated and natural ultraviolet aging, which was confirmed by inspecting the surface morphology of irradiated polymeric films. For example, atomic force microscopy revealed that the roughness factor of polymers' irradiated surfaces was improved significantly in the presence of ultraviolet absorbers. In addition, the investigation of the surface of irradiated polymers using scanning electron microscopy showed a high degree of homogeneity and the appearance of pores that were different in size and shape. The current work surveys for the first time the use of newly synthesized, ultraviolet absorbers as additives to enhance the photostability of polymeric materials and, in particular, polyvinyl chloride and polystyrene, based mainly on our own recent work in the field.