Functional group surface modifications for enhancing the formation and performance of exoelectrogenic biofilms on the anode of a bioelectrochemical system

Recent Advances in Scaling up Bioelectrochemical Systems: A Review

Bioelectrochemical systems (BESs) are devices capable of converting chemical energy into electrical energy using microorganisms as catalysts. These systems have been extensively studied at the laboratory level, but, due to multiple difficulties, their large-scale implementation has been explored only sparingly. This study presents the most recent technological advances for scaling up BESs. In the same way, the main technical and economic challenges that hinder the correct implementation of these systems at a large scale are mentioned. The study concludes with a review of successful case studies in scaling up BESs and discusses future directions and emerging trends.

In Situ Biosynthesis of FeS Nanoparticles Boosts Current Generation in Bioelectrochemical Systems Through Efficient Electron Transfer

The utility of electrochemical active biofilm in bioelectrochemical systems has received considerable attention for harvesting energy and chemical products. However, the slow electron transfer between biofilms and electrodes hinders the enhancement of performance and still remains challenging. Here, using Fe3O4 /L-Cys nanoparticles as precursors to induce biomineralization, a facile strategy for the construction of an effective electron transfer pathway through biofilm and biological/inorganic interface is proposed, and the underlying mechanisms are elucidated. Taking advantage of an on-chip interdigitated microelectrode array (IDA), the conductive current of biofilm that is related to the electron transfer process within biofilm is characterized, and a 2.10-fold increase in current output is detected. The modification of Fe3O4/L-Cys on the electrode surface facilitates the electron transfer between the biofilm and the electrode, as the bio/inorganic interface electron transfer resistance is only 16% compared to the control. The in-situ biosynthetic Fe-containing nanoparticles (e.g., FeS) enhance the transmembrane EET and the EET within biofilm, and the peak conductivity increases 3.4-fold compared to the control. The in-situ biosynthesis method upregulates the genes involved in energy metabolism and electron transfer from the transcriptome analysis. This study enriches the insights of biosynthetic nanoparticles on electron transfer process, holding promise in bioenergy conversion.

Advanced Electroanalysis for Electrosynthesis

Electrosynthesis is a popular, environmentally friendly substitute for conventional organic methods. It involves using charge transfer to stimulate chemical reactions through the application of a potential or current between two electrodes. In addition to electrode materials and the type of reactor employed, the strategies for controlling potential and current have an impact on the yields, product distribution, and reaction mechanism. In this Review, recent advances related to electroanalysis applied in electrosynthesis were discussed. The first part of this study acts as a guide that emphasizes the foundations of electrosynthesis. These essentials include instrumentation, electrode selection, cell design, and electrosynthesis methodologies. Then, advances in electroanalytical techniques applied in organic, enzymatic, and microbial electrosynthesis are illustrated with specific cases studied in recent literature. To conclude, a discussion of future possibilities that intend to advance the academic and industrial areas is presented.

Scaling up of dual-chamber microbial electrochemical systems - An appraisal using systems design approach

Impetus to minimise the energy and carbon footprints of evolving wastewater resource recovery facilities has promoted the development of microbial electrochemical systems (MES) as an emerging energy-neutral and sustainable platform technology. Using separators in dual-chamber MES to isolate anodic and cathodic environments creates endless opportunities for its myriad applications. Nevertheless, the high internal resistance and the complex interdependencies among various system factors have challenged its scale-up. This critical review employed a systems approach to examine the complex interdependencies and practical issues surrounding the implementation and scalability of dual-chamber MES, where the anodic and cathodic reactions are mutually appraised to improve the overall system efficiency. The robustness and stability of anodic biofilms in large-volume MES is dependent on its inoculum source, antecedent history and enrichment strategies. The composition and anode-respiring activity of these biofilms are modulated by the anolyte composition, while their performance demands a delicate balance between the electrode size, macrostructure and the availability of substrates, buffers and nutrients when using real wastewater as anolyte. Additionally, the catholyte governed the reduction environment and associated energy consumption of MES with scalable electrocatalysts needed to enhance the sluggish reaction kinetics for energy-efficient resource recovery. A comprehensive assessment of the dual-chamber reactor configuration revealed that the tubular, spiral-wound, or plug-in modular MES configurations are suitable for pilot-scale, where it could be designed more effectively using efficient electrode macrostructure, suitable membranes and bespoke strategies for continuous operation to maximise their performance. It is anticipated that the critical and analytical understanding gained through this review will support the continuous development and scaling-up of dual-chamber MES for prospective energy-neutral treatment of wastewater and simultaneous circular management of highly relevant environmental resources.

Synergistic effect of electrotrophic perchlorate reducing microorganisms and chemically modified electrodes for enhancing bioelectrochemical perchlorate removal

Perchlorate has been described as an emerging pollutant that compromises water sources and human health. In this study, a new electrotrophic perchlorate reducing microorganism (EPRM) isolated from the Atacama Desert, Dechloromonas sp. CS-1, was evaluated for perchlorate removal in water in a bioelectrochemical reactor (BER) with a chemically modified electrode. BERs were operated for 17 days under batch mode conditions with an applied potential of -500 mV vs. Ag/AgCl. Surface analysis (i.e., SEM, XPS, FT-IR, RAMAN spectroscopy) on the modified electrode demonstrated heterogeneous transformation of the carbon fibers with the incorporation of nitrogen functional groups and the oxidation of the carbonaceous material. The BERs with the modified electrode and the presence of the EAM reached high cathodic efficiency (90.79 ± 9.157%) and removal rate (0.34 ± 0.007 mol m-3-day) compared with both control conditions. The observed catalytic enhancement of CS-1 was confirmed by a reduction in the charge transfer resistance obtained by electrochemical impedance spectroscopy (EIS). Finally, an electrochemical kinetic study revealed an eight-electron perchlorate bioreduction reaction at -638.33 ± 24.132 mV vs. Ag/AgCl. Therefore, our results show the synergistic effect of EPRM and chemically modified electrodes on perchlorate removal in a BER.

Electrospinning micro-nanofibers immobilized aerobic denitrifying bacteria for efficient nitrogen removal in wastewater

Electrospinning micro-nanofibers with exceptional physicochemical properties and biocompatibility are becoming popular in the medical field. These features indicate its potential application as microbial immobilized carriers in wastewater treatment. Here, aerobic denitrifying bacteria were immobilized on micro-nanofibers, which were prepared using different concentrations of polyacrylonitrile (PAN) solution (8%, 12% and 15%). The results of diameter distribution, specific surface area and average pore diameter indicated that 15% PAN micro-nanofibers with tighter surface structure were not suitable as microbial carriers. The bacterial load results showed that the cell density (OD₆₀₀) and total protein of 12% PAN micro-nanofibers were 107.14% and 106.28% higher than those of 8% PAN micro-nanofibers. Subsequently, the 12% PAN micro-nanofibers were selected for aerobic denitrification under the different C/N ratios (1.5-10), and stable performance was obtained. Bacterial community analysis further manifested that the micro-nanofibers effectively immobilized bacteria and enriched bacterial structure under the high C/N ratios. Therefore, the feasibility of micro-nanofibers as microbial carriers was confirmed. This work was of great significance for promoting the application of electrospinning for microbial immobilization in wastewater treatment.

Nitrobenzene reduction promoted by the integration of carbon nanotubes and Geobacter sulfurreducens

Electron shuttles (ES) can mediate long-distance electron transfer between extracellular respiratory bacteria (ERB) and the surroundings. However, the effects of graphite structure in ES on the extracellular electron transfer (EET) process remain ambiguous. This work investigated the function of graphite structure in the process of nitrobenzene (NB) degradation by Geobacter sulfurreducens PCA, in which highly aromatic carbon nanotubes (CNTs) was studied as a typical ES. The results showed that the addition of 1.5 g L^-1 of CNTs improved the NB biodegradation up to 81.2%, plus 18.8% NB loss due to the adsorption property of CNTs, achieving complete removal of 200 μM NB within 9 h. The amendment of CNTs greatly increased the EET rate, indicating that graphite structure exhibited excellent electron shuttle performance. Furthermore, Raman spectrum proved that CNTs obtained better graphite structure after 90 h of cultivation with strain PCA, resulting in higher electrochemical performance. Also, CNTs was perceived as the "Contaminant Reservoir", which alleviated the toxic effect of NB and shortened the distance of EET process. Overall, this work focused on the effects of material graphite structure on the EET process, which enriched the understanding of the interaction between CNTs and ERB, and these results might promote their application in the in-situ bioremediation of nitroaromatic-polluted environment.

Sensitive organic electrochemical transistor biosensors: Comparing single and dual gate functionalization and different COOH-functionalized bioreceptor layers

We developed new measurement configurations based on organic electrochemical transistors (OECTs). Three types of COOH-functionalized bioreceptor layers were deposited on indium tin oxide (ITO) electrodes on poly(ethylene terephthalate) (PET) substrates and their performance was tested using single gate functionalization organic electrochemical transistor (S-OECT) and dual gate functionalization organic electrochemical transistor (D-OECT) configurations. The three layers included one p-type semiconductor, one insulator, and one self-assembled layer, and the dual gates were connected in series through buffer solutions, so the solution-electrode interfaces had the opposite polarities. We investigated the sensitivities of these systems using the human IgG antigen-human IgG antibody receptor pair for main experiments, and drifts of antibody-functionalized gates without analytes as control experiments. Drifts without analyte can obscure the real sensitivity. We show that the D-OECT has the capability to cancel the drifts, and is also beneficial for showing the sensitivity more exactly. This configuration has the ability to increase the accuracy of antibody-antigen interaction detection, and further decrease or eliminate the effect of ions in the buffer solution. We also prove that the D-OECT can work well with different bioreceptor materials, which indicates that the system can be further applied to different conditions.

Modification of carbon foam with 4-mercaptobenzoic acid functionalised gold nanoparticles for an application in a yeast-based microbial fuel cell

Modification of carbon foam with gold nanoparticles (AuNPs) was successfully performed through a hydrothermal method. The modified AuNPs were functionalised with 4-mercaptobenzoic acid (MBA) to improve their affinity toward microorganisms. TEM and SEM characterization indicated that although polydisperse spherical nanoparticles of AuNPs with particle sizes around 17 nm were obtained, the attached nanoparticles were agglomerated to be around 0.4 to 1.5 μm in size on the carbon foam surface. The electrochemical studies using cyclic voltammetry technique affirmed that the modified carbon foam electrodes have electroactive properties against glucose. Evaluation of the electrode was performed for a microbial fuel cell using Candida fukuyamaensis yeast as the microorganisms. The polarization curves showed that functionalisation of AuNPs-modified carbon foam with MBA provides around three times higher current density (1226.93 mA m-2) and power density (330.61 mW m-2) compared to the unmodified one. This result indicated that the modification is suitable to improve yeast attachment on the electrode surface.

Paracetamol degradation pathways in soil after biochar addition

Little is known about the effect of biochar on the degradation of paracetamol in soil, considering the ubiquity of this pollutant in the environment. Given the importance of the electrochemical properties of biochar for contaminant remediation, we investigated the influence of raw and designer redox-active biochars on paracetamol degradation in soil. Metabolite quantification indicated that a minimum of 53% of the spiked paracetamol was transformed in biochar-amended soil, resulting in the accumulation of different degradation products. The identification of these products allowed us to chart paracetamol degradation pathways in soil with and without biochar amendment. Some of the major degradation routes were observed to proceed via catechol and phenol, despite being previously described as having only a minor role in paracetamol metabolism. Additionally, a new transformation route from paracetamol to NAPQI was discovered in anaerobic soil originating from direct redox reactions on the surface of the designer biochars. These results may contribute to change our understanding of the environmental fate of paracetamol in soil and the role of biochar in its biodegradation.

Self-produced biophotosensitizers enhance the degradation of organic pollutants in photo-bioelectrochemical systems

Bioelectrochemical systems (BESs) with integrated photoactive components have been shown to be a promising strategy for enhancing the performance for bioenergy generation and pollutant removal. This study revealed an efficient photo-BES with an enhanced pollutant degradation rate by utilizing self-produced biomolecules as photosensitizers in situ. Results showed that the BES could increase the coulombic efficiency from 60.8% to 73.0% and the degradation rate of bisphenol A (BPA) from 0.030 to 0.189 h^-1 when the suspension in the reactor was illuminated with simulated sunlight in the absence of any external photosensitizers. We identified that the regular BES released many organic substances into the reactor during operation. These substances, including dissolved biomolecules and solid cell residues, were photoactive for producing hydroxyl radicals during light illumination. Quenching experiments verified that the •OH generated from the self-produced biophotosensitizers contributed to the enhanced degradation of BPA. Additionally, the phototransformation of biophotosensitizers was also observed in photo-BES. The quantity of tyrosine protein-like components decreased, but that of the humic components remained relatively stable. Our findings imply that BESs with integrated self-produced biophotosensitizers may be promising for constructing advanced electrochemical and biological systems for synchronous bioelectricity production and degradation of organic pollutants in wastewater treatments.

A review of biomass immobilization in anammox and partial nitrification/anammox systems: Advances, issues, and future perspectives

Two biomass immobilization techniques; entrapment and carrier-based, attract increasing attention in anammox and partial nitrification/anammox (PN/A) systems. This paper provides a comprehensive review of the advances, outstanding issues, and future research directions in this field. The application of both entrapment and carrier-based biofilm immobilization for reactor start up, improving the nitrogen removal performance, and protecting autotrophic bacteria from environmental fluctuations in anammox and partial nitrification/anammox systems are summarized and discussed. The key characteristics of carriers for biomass immobilization are biocompatibility for supporting microbial growth, permeability for effective mass transfer, and physical/chemical stability for long-term use. Carriers without these characteristics must be improved and re-evaluated for their feasibility in applications. Lab-scale, pilot, and full-scale studies are needed to overcome the potential obstacles of preliminary studies, and to investigate the long-term performance of biomass immobilization techniques, especially using real wastewater as influent, which may introduce more complexity and threaten the carrier's immobilization. In addition, calculating the 'nitrogen removal rate normalized by the packing ratio of carriers (NRR-C)' in the immobilization system is strongly suggested to obtain a direct comparison of immobilization performance/limitations from different studies. This review will improve understanding of the major challenges of immobilization technology in anammox and PN/A systems and provide insights into the next-stage of research and full-scale applications.

Solution-Deposited and Patternable Conductive Polymer Thin-Film Electrodes for Microbial Bioelectronics

Microbial bioelectronic devices integrate naturally occurring or synthetically engineered electroactive microbes with microelectronics. These devices have a broad range of potential applications, but engineering the biotic-abiotic interface for biocompatibility, adhesion, electron transfer, and maximum surface area remains a challenge. Prior approaches to interface modification lack simple processability, the ability to pattern the materials, and/or a significant enhancement in currents. Here, a novel conductive polymer coating that significantly enhances current densities relative to unmodified electrodes in microbial bioelectronics is reported. The coating is based on a blend of poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) crosslinked with poly(2-hydroxyethylacrylate) (PHEA) along with a thin polydopamine (PDA) layer for adhesion to an underlying indium tin oxide (ITO) electrode. When used as an interface layer with the current-producing bacterium Shewanella oneidensis MR-1, this material produces a 178-fold increase in the current density compared to unmodified electrodes, a current gain that is higher than previously reported thin-film 2D coatings and 3D conductive polymer coatings. The chemistry, morphology, and electronic properties of the coatings are characterized and the implementation of these coated electrodes for use in microbial fuel cells, multiplexed bioelectronic devices, and organic electrochemical transistor based microbial sensors are demonstrated. It is envisioned that this simple coating will advance the development of microbial bioelectronic devices.

Overcoming biochar limitations to remediate pentachlorophenol in soil by modifying its electrochemical properties

In this study, we produced modified biochars with enhanced electrochemical properties to increase PCP remediation in soil. Although all biochars enhanced PCP remediation in aerobic conditions, only a few did in anaerobic soil. The most successful modifications were (i) the preloading of biomass with 10% w/w FeCl₃, to obtain a biochar rich in redox-active metals (B-Fe); (ii) the oxidation of a conductive biochar pyrolyzed at 1000 ºC with 0.025 M KMnO₄, to produce a biochar with both moderate conductivity and redox capacity (B-1000-KMnO₄); and (iii) KMnO₄ oxidation of an amorphous biochar pyrolyzed at 400 ºC to obtain a biochar with very high redox capacity (B-KMnO₄). B-Fe reduced extractable PCP to almost zero after 50 days in both incubations, but showed slow kinetics of remediation in aerobic soil. B-1000-KMnO₄ had the highest rate of remediation under aerobic conditions, but no significant effect under anaerobic conditions. B-KMnO₄, however, presented high rates of remediation and high removal of extractable PCP under both conditions, which made it the recommended modification strategy for increased PCP remediation. We found that the degree of remediation primarily depends on the redox capacity, while the rate of remediation was determined by both the conductivity and redox capacity of biochar.

Biotic Cathode of Graphite Fibre Brush for Improved Application in Microbial Fuel Cells

The biocathode in a microbial fuel cell (MFC) system is a promising and a cheap alternative method to improve cathode reaction performance. This study aims to identify the effect of the electrode combination between non-chemical modified stainless steel (SS) and graphite fibre brush (GFB) for constructing bio-electrodes in an MFC. In this study, the MFC had two chambers, separated by a cation exchange membrane, and underwent a total of four different treatments with different electrode arrangements (anodeǁcathode)—SSǁSS (control), GFBǁSS, GFBǁGFB and SSǁGFB. Both electrodes were heat-treated to improve surface oxidation. On the 20th day of the operation, the GFBǁGFB arrangement generated the highest power density, up to 3.03 W/m3 (177 A/m3), followed by the SSǁGFB (0.0106 W/m3, 0.412 A/m3), the GFBǁSS (0.0283 W/m3, 17.1 A/m3), and the SSǁSS arrangements (0.0069 W/m−3, 1.64 A/m3). The GFBǁGFB had the lowest internal resistance (0.2 kΩ), corresponding to the highest power output. The other electrode arrangements, SSǁGFB, GFBǁSS, and SSǁSS, showed very high internal resistance (82 kΩ, 2.1 kΩ and 18 kΩ, respectively) due to the low proton and electron movement activity in the MFC systems. The results show that GFB materials can be used as anode and cathode in a fully biotic MFC system.

Advances in interfacial engineering for enhanced microbial extracellular electron transfer

The extracellular electron transfer (EET) efficiency between electroactive microbes (EAMs) and electrode is a key factor determining the development of microbial electrochemical technology (MET). Currently, the low EET efficiency of EAMs limits the application of MET in the fields of organic matter degradation, electric energy production, seawater desalination, bioremediation and biosensing. Enhancement of the interaction between EAMs and electrode by interfacial engineering methods brings bright prospects for the improvement of the EET efficiency of EAMs. In view of the research in recent years, this mini-review systematically summarizes various interfacial engineering strategies ranging from electrode surface modification to hybrid biofilm formation, then to single cell interfacial engineering and intracellular reformation for promoting the electron transfer between EAMs and electrode, focusing on the applicability and limitations of these methodologies. Finally, the possible key directions, challenges and opportunities for future interfacial engineering to strengthen the microbial EET are proposed in this mini-review.

Electrotaxis-mediated cell motility and nutrient availability determine Chlamydomonas microsphaera-surface interactions in bioelectrochemical systems

Cell attachment onto electrode-forming biocathodes is a promising alternative to expensive catalysts used for electricity production in bioelectrochemical systems (BESs). Though BESs have been extensively studied for decades, the processes, underlying mechanisms, and determinant driving forces of microalgal biocathode formation remain largely unknown. In this study, we employed a model unicellular motile microalga, Chlamydomonas microsphaera, to investigate the microalgal attachment processes onto the electrode surface of a BES and to identify the determinant factors. Results showed that the initial attachment of C. micrrosphaera cells is determined by the applied external voltage rather than nutrient availability and occurs via electrotaxis-mediated cell motility. The subsequent development of the C. microsphaera biofilm is then increasingly determined by nutrient availability. Our results revealed that, in the absence of an external voltage, nutrient availability remains a dominant factor controlling the fate of the microalgal surface attachment and subsequent biofilm formation processes. Thus, our results show that electrotactic and chemotactic movements are crucial to facilitate the initial attachment and subsequent biofilm formation of C. microsphaera onto the electrode surfaces of BES. This study provides new insights into the mechanisms of microalgal surface attachment and biofilm formation processes on microalgal biocathodes, which hold great promise for improving the electrochemical properties of cathodes.

Beneficial biofilms: A mini-review of strategies to enhance biofilm formation for biotechnological applications

The capacity of bacteria to form biofilms is an important trait for their survival and persistence. Biofilms occur naturally in soil and aquatic environments, are associated with animals ranging from insects to humans and are also found in built environments. They are typically encountered as a challenge in healthcare, food industry, and water supply ecosystems. In contrast, they are known to play a key role in the industrial production of commercially valuable products, environmental remediation processes, and in microbe-catalysed electrochemical systems for energy and resource recovery from wastewater. While there are many recent articles on biofilm control and removal, review articles on promoting biofilm growth for biotechnological applications are unavailable. Biofilm formation is a tightly regulated response to perturbations in the external environment. The multi-stage process, mediated by an assortment of proteins and signaling systems, involves the attachment of bacterial cells to a surface followed by their aggregation in a matrix of extracellular polymeric substances. Biofilms can be promoted by altering the external environment in a controlled manner, supplying molecules that trigger the aggregation of cells and engineering genes associated with biofilm development. This mini-review synthesizes findings from studies that have described such strategies and highlights areas needing research attention.

Liposoluble quinone promotes the reduction of hydrophobic mineral and extracellular electron transfer of Shewanella oneidensis MR-1

A large number of reaction systems are composed of hydrophobic interfaces and microorganisms in natural environment. However, it is not clear how microorganisms adjust their breathing patterns and respond to hydrophobic interfaces. Here, Shewanella oneidensis MR-1 was used to reduce ferrihydrite of a hydrophobic surface. Through Fe(II) kinetic analysis, it was found that the reduction rate of hydrophobic ferrihydrite was 1.8 times that of hydrophilic one. The hydrophobic surface of the mineral hinders the way the electroactive microorganism uses the water-soluble electron mediator riboflavin for indirect electron transfer and promotes MR-1 to produce more liposoluble quinones. Ubiquinone can mediate electron transfer at the hydrophobic interface. Ubiquinone-30 (UQ-6) increases the reduction rate of hydrophobic ferrihydrite from 38.5 ± 4.4 to 52.2 ± 0.8 μM·h⁻¹. Based on the above experimental results, we propose that liposoluble electron mediator ubiquinone can act on the extracellular hydrophobic surface, proving that the metabolism of hydrophobic minerals is related to endogenous liposoluble quinones. Hydrophobic modification of minerals encourages electroactive microorganisms to adopt differentiated respiratory pathways. This finding helps in understanding the electron transfer behavior of the microbes at the hydrophobic interface and provides new ideas for the study of hydrophobic reactions that may occur in systems, such as soil and sediment.

•

Extracellular electron transfer can be regulated by wettability of mineral surface

•

Hydrophobic surface hinders the transport of water-soluble mediator riboflavin

•

Ubiquinone can mediate extracellular electron transfer at the hydrophobic interface

Industrially scalable surface treatments to enhance the current density output from graphite bioanodes fueled by real domestic wastewater

Acid and electrochemical surface treatments of graphite electrode, used individually or in combination, significantly improved the microbial anode current production, by +17% to +56%, in well-regulated and duplicated electroanalytical experimental systems. Of all the consequences induced by surface treatments, the modifications of the surface nano-topography preferentially justify an improvement in the fixation of bacteria, and an increase of the specific surface area and the electrochemically accessible surface of graphite electrodes, which are at the origin of the higher performances of the bioanodes supplied with domestic wastewater. The evolution of the chemical composition and the appearance of C-O, C=O, and O=C-O groups on the graphite surface created by combining acid and electrochemical treatments was prejudicial to the formation of efficient domestic-wastewater-oxidizing bioanodes. The comparative discussion, focused on the positioning of the performances, shows the industrial interest of applying the surface treatment method to the world of bioelectrochemical systems.

Anode Surface Bioaugmentation Enhances Deterministic Biofilm Assembly in Microbial Fuel Cells

Microbial fuel cells (MFCs) generate energy while aiding the biodegradation of waste through the activity of an electroactive mixed biofilm. Metabolic cooperation is essential for MFCs' efficiency, especially during early colonization. Thus, examining specific ecological processes that drive the assembly of anode biofilms is highly important for shortening startup times and improving MFC performance, making this technology cost-effective and sustainable. Here, we use metagenomics to show that bioaugmentation of the anode surface with a taxonomically defined electroactive consortium, dominated by Desulfuromonas, resulted in an extremely rapid current density generation. Conversely, the untreated anode surface resulted in a highly stochastic and slower biofilm assembly. Remarkably, an efficient anode colonization process was obtained only if wastewater was added, leading to a nearly complete replacement of the bioaugmented community by Geobacter lovleyi Although different approaches to improve MFC startup have been investigated, we propose that only the combination of anode bioaugmentation with wastewater inoculation can reduce stochasticity. Such an approach provides the conditions that support the growth of specific newly arriving species that positively support the fast establishment of a highly functional anode biofilm.IMPORTANCE Mixed microbial communities play important roles in treating wastewater, in producing renewable energy, and in the bioremediation of pollutants in contaminated environments. While these processes are well known, especially the community structure and biodiversity, how to efficiently and robustly manage microbial community assembly remains unknown. Moreover, it has been shown that a high degree of temporal variation in microbial community composition and structure often occurs even under identical environmental conditions. This heterogeneity is directly related to stochastic processes involved in microbial community organization, similarly during the initial stages of biofilm formation on surfaces. In this study, we show that anode surface pretreatment alone is not sufficient for a substantial improvement in startup times in microbial fuel cells (MFCs), as previously thought. Rather, we have discovered that the combination of applying a well-known consortium directly on the anode surface together with wastewater (including the bacteria that they contain) is the optimized management scheme. This allowed a selected colonization process by the wastewater species, which improved the functionality relative to that of untreated systems.

Good microbial affinity of phenolic carbon felt as an efficient anode for microbial fuel cells

Phenolic carbon felt (PCF) is a three-dimensional material with a simple manufacturing process and low cost. To investigate the application of PCF as an anode material for use in microbial fuel cells (MFCs), we employed PCF as the anode material for the first time in MFCs that were carbonized at different temperatures. The relationship between the intrinsic characteristics and the electrochemical performance of different PCFs was also analyzed. Here, we obtained the best power generation with a power density of up to 2600 mW/m² when PCF was heated to 900 °C (PCF-900); this power generation was much higher than that of the commercial carbon felts. From SEM images, we found that the biofilm growth of PCF-900 was quite uniform. This may result from the higher surface electropositivity of PCF-900 and increased electrostatic attraction between the microorganisms and PCF. We also analyzed the conductivity, specific surface area, functional groups, and surface charge of the PCF anode. Under the synergistic effect of these intrinsic properties, PCF-900 showed good biocompatibility for the adhesion of microorganisms and high electron transfer efficiency. In addition, PCF was easily prepared in different sizes. Thus, it could be a promising material for the application of scale-up MFCs.

100th Anniversary of Macromolecular Science Viewpoint: Soft Materials for Microbial Bioelectronics

Bioelectronics brings together the fields of biology and microelectronics to create multifunctional devices with the potential to address longstanding technological challenges and change our way of life. Microbial electrochemical devices are a growing subset of bioelectronic devices that incorporate naturally occurring or synthetically engineered microbes into electronic devices and have broad applications including energy harvesting, chemical production, water remediation, and environmental and health monitoring. The goal of this Viewpoint is to highlight recent advances and ongoing challenges in the rapidly developing field of microbial bioelectronic devices, with an emphasis on materials challenges. We provide an overview of microbial bioelectronic devices, discuss the biotic-abiotic interface in these devices, and then present recent advances and ongoing challenges in materials related to electron transfer across the abiotic-biotic interface, microbial adhesion, redox signaling, electronic amplification, and device miniaturization. We conclude with a summary and perspective of the field of microbial bioelectronics.

Gel immobilization: A strategy to improve the performance of anaerobic ammonium oxidation (anammox) bacteria for nitrogen-rich wastewater treatment

Anaerobic ammonium oxidation (anammox) process appears a suitable substitute to nitrification-denitrification at a lower C/N ratios. Anammox is a chemolithoautotrophic process, belong to phylum Planctomycetes, and they are slow growing bacteria. Different strategies, e.g., biofilm formation, granulation and gel immobilization, have been applied to maintain a critical mass of bacterial cells in the system by avoiding washout from the bioreactor. Gel immobilization of anammox appears the best alternative to the natural process of biofilm formation and granulation. Polyvinyl alcohol-sodium alginate, polyethylene glycol, and waterborne polyurethane are the most reported materials used for the entrapment of anammox bacteria. However, dissolution of the gel beads refrains its application for long term bioprocess. Magnetic powder could coat on the surface of the beads which may increase the mechanical strength and durability of pellets. Application and problem of immobilization technology for the commercialization of this technology also addressed.

Enhanced Performance of Microbial Fuel Cells with Anodes from Ethylenediamine and Phenylenediamine Modified Graphite Felt

A microbial fuel cell (MFC) is a promising renewable energy option, which enables the effective and sustainable harvesting of electrical power due to bacterial activity and, at the same time, can also treat wastewater and utilise organic wastes or renewable biomass. However, the practical implementation of MFCs is limited and, therefore, it is important to improve their performance before they can be scaled up. The surface modification of anode material is one way to improve MFC performance by enhancing bacterial cell adhesion, cell viability and extracellular electron transfer. The modification of graphite felt (GF), used as an anode in MFCs, by electrochemical oxidation followed by the treatment with ethylenediamine or p-phenylenediamine in one-step short duration reactions with the aim of introducing amino groups on the surface of GF led to the enhancement of the overall performance characteristics of MFCs. The MFC with the anode from GF modified with p-phenylenediamine provided approx. 32% higher voltage than the control MFC with a bare GF anode, when electric circuits of the investigated MFCs were loaded with resistors of 659 Ω. Its surface power density was higher by approx. 1.75 times than that of the control. Decreasing temperature down to 0 °C resulted in just an approx. 30% reduction in voltage generated by the MFC with the anode from GF modified with p-phenylenediamine.

Defective S/N co-doped carbon cloth via a one-step process for effective electroreduction of nitrogen to ammonia

The electroreduction of nitrogen (N₂) has gained increasing attention as a promising route to achieve green and sustainable ammonia (NH₃) production.

L. M. A carbon nanotube reinforced functionalized styrene–maleic anhydride copolymer as an advanced electrode material for efficient energy storage applications

In the wake of the global energy crisis, innovative materials are being developed to alleviate the energy shortage by utilizing the available sources sustainably.