Shear induced alignment of short nanofibers in 3D printed polymer composites

Investigation of 3D Printed Self-Sensing UHPC Composites Using Graphite and Hybrid Carbon Microfibers

This paper explores the development of 3D-printed self-sensing Ultra-High Performance Concrete (UHPC) by incorporating graphite (G) powder, milled carbon microfiber (MCMF), and chopped carbon microfiber (CCMF) as additives into the UHPC matrix to enhance piezoresistive properties while maintaining workability for 3D printing. Percolation curves were established to identify optimal filler inclusion levels, and a series of compressive tests, including quasi-static cyclic, dynamic cyclic, and monotonic compressive loading, were conducted to evaluate the piezoresistive and mechanical performance of 29 different mix designs. It was found that incorporating G powder improved the conductivity of the UHPC but decreased compressive strength for both mold-cast and 3D-printed specimens. However, incorporating either MCMF or CCMF into the UHPC resulted in the maximum 9.8% and 19.2% increase in compressive strength and Young's modulus, respectively, compared to the plain UHPC. The hybrid combination of MCMF and CCMF showed particularly effective in enhancing sensing performance, achieving strain linearity over 600 με. The best-preforming specimens (3G250M250CCMF) were fabricated using 3 wt% of G, 0.25 wt% of MCMF, and 0.25 wt% of CCMF, yielding a maximum strain gauge factor of 540, a resolution of 68 με, and an accuracy of 4.5 με under axial compression. The 3D-printed version of the best-performing specimens exhibited slightly diminished piezoresistive and mechanical behaviors compared to their mold-cast counterparts, yielding a maximum strain gauge factor of 410, a resolution of 99 με, and an accuracy of 8.6 με.

Biobased Resin for Sustainable Stereolithography: 3D Printed Vegetable Oil Acrylate Reinforced with Ultra-Low Content of Nanocellulose for Fossil Resin Substitution

The use of biobased materials in additive manufacturing is a promising long-term strategy for advancing the polymer industry toward a circular economy and reducing the environmental impact. In commercial 3D printing formulations, there is still a scarcity of efficient biobased polymer resins. This research proposes vegetable oils as biobased components to formulate the stereolithography (SLA) resin. Application of nanocellulose filler, prepared from agricultural waste, remarkably improves the printed material's performance properties. The strong bonding of nanofibrillated celluloses' (NFCs') matrix helps develop a strong interface and produce a polymer nanocomposite with enhanced thermal properties and dynamical mechanical characteristics. The ultra-low NFC content of 0.1-1.0 wt% (0.07-0.71 vol%) was examined in printed samples, with the lowest concentration yielding some of the most promising results. The developed SLA resins showed good printability, and the printing accuracy was not decreased by adding NFC. At the same time, an increase in the resin viscosity with higher filler loading was observed. Resins maintained high transparency in the 500-700 nm spectral region. The glass transition temperature for the 0.71 vol% composition increased by 28°C when compared to the nonreinforced composition. The nanocomposite's stiffness has increased fivefold for the 0.71 vol% composition. The thermal stability of printed compositions was retained after cellulose incorporation, and thermal conductivity was increased by 11%. Strong interfacial interactions were observed between the cellulose and the polymer in the form of hydrogen bonding between hydroxyl and ester groups, which were confirmed by Fourier-transform infrared spectroscopy. This research demonstrates a great potential to use acrylated vegetable oils and nanocellulose fillers as a feedstock to produce high-performance resins for sustainable SLA 3D printing.

Influence of the Type of Nanofillers on the Properties of Composites Used in Dentistry and 3D Printing

Photopolymerization is a growing field with an extensive range of applications and is environmentally friendly owing to its energy-efficient nature. Such light-assisted curing methods were initially used to cure the coatings. However, it has become common to use photopolymerization to produce 3D objects, such as bridges or dental crowns, as well as to cure dental fillings. In this study, polymer nanocomposites containing inorganic nanofillers (such as zinc nano-oxide and zinc nano-oxide doped with two wt.% aluminum, titanium nano-oxide, kaolin nanoclay, zirconium nano-oxide, aluminum nano-oxide, and silicon nano-oxide) were fabricated and studied using Real Time FT-IR to investigate the effects of these nanoadditives on the final conversion rates of the obtained nanocomposites. The effects of the fillers on the viscosity of the produced nanocomposites were also investigated, and 3D prints of the selected nanocomposites were presented.

Interfacial Regulation for 3D Printing based on Slice-Based Photopolymerization

3D printing, also known as additive manufacturing, can turn computer-aided designs into delicate structures directly and on demand by eliminating expensive molds, dies, or lithographic masks. Among the various technical forms, light-based 3D printing mainly involved the control of polymer-based matter fabrication and realized a field of manufacturing with high tunability of printing format, speed, and precision. Emerging slice- and light-based 3D-printing methods have prosperously advanced in recent years but still present challenges to the versatility of printing continuity, printing process, and printing details control. Herein, the field of slice- and light-based 3D printing is discussed and summarized from the view of interfacial regulation strategies to improve the printing continuity, printing process control, and the character of printed results, and several potential strategies to construct complex 3D structures of distinct characteristics with extra external fields, which are favorable for the further improvement and development of 3D printing, are proposed.

3D-Printed Fiber-Reinforced Polymer Composites by Fused Deposition Modelling (FDM): Fiber Length and Fiber Implementation Techniques

Fused Deposition Modelling (FDM) is an actively growing additive manufacturing (AM) technology due to its ability to produce complex shapes in a short time. AM, also known as 3-dimensional printing (3DP), creates the desired shape by adding material, preferably by layering contoured layers on top of each other. The need for low cost, design flexibility and automated manufacturing processes in industry has triggered the development of FDM. However, the mechanical properties of FDM printed parts are still weaker compared to conventionally manufactured products. Numerous studies and research have already been carried out to improve the mechanical properties of FDM printed parts. Reinforce polymer matrix with fiber is one of the possible solutions. Furthermore, reinforcement can enhance the thermal and electrical properties of FDM printed parts. Various types of fibers and manufacturing methods can be adopted to reinforce the polymer matrix for different desired outcomes. This review emphasizes the fiber types and fiber insertion techniques of FDM 3D printed fiber reinforcement polymer composites. A brief overview of fused deposition modelling, polymer sintering and voids formation during FDM printing is provided, followed by the basis of fiber reinforced polymer composites, type of fibers (synthetic fibers vs. natural fibers, continuous vs. discontinuous fiber) and the composites' performance. In addition, three different manufacturing methods of fiber reinforced thermoplastics based on the timing and location of embedding the fibers, namely 'embedding before the printing process (M1)', 'embedding in the nozzle (M2)', and 'embedding on the component (M3)', are also briefly reviewed. The performance of the composites produced by three different methods were then discussed.

3D Printing for Cartilage Replacement: A Preliminary Study to Explore New Polymers

The use of additive manufacturing technologies for biomedical applications must begin with the knowledge of the material to be used, by envisaging a very specific application rather than a more general aim. In this work, the preliminary study was focused on considering the cartilaginous tissue. This biological tissue exhibits different characteristics, such as thickness and mechanical properties, depending on its specific function in the body. Due to the lack of vascularization, cartilage is a supporting connective tissue with limited capacity for recovery and regeneration. For this reason, any approach, whether to repair/regenerate or as a total replacement, needs to fulfill the adequate mechanical and chemical properties of the surrounding native cartilage to be successful. This work aims to explore the possibility of using new polymers for cartilage total replacement approaches with polymeric materials processed with the specific 3D printing technique of fused filament fabrication (FFF). The materials studied were Nylon^® 12 (PA12), already described for this purpose, and LAY-FOMM^® 60 (FOMM). FOMM has not been described in the literature for biomedical purposes. Therefore, the chemical, thermal, swelling capacity, and mechanical properties of the filaments were thoroughly characterized to better understand the structure–properties–application relationships of this new polymer. In addition, as the FFF technology is temperature based, the properties were also evaluated in the printed specimens. Due to the envisaged application, the specimens were also characterized in the wet state. When comparing the obtained results with the properties of native cartilage, it was possible to conclude that: (i) PA12 exhibits low swelling capacity, while FOMM, in its dry and wet forms, has a higher swelling capacity, closer to that of native cartilage; (ii) the mechanical properties of the polymeric materials, especially PA12, are higher than those of native cartilage; and (iii) from the mechanical properties evaluated by ultra-micro hardness tests, the values for FOMM indicate that this material could be a good alternative for cartilage replacement in older patients. This preliminary study, essentially devoted to expanding the frontiers of the current state of the art of new polymeric materials, provides valuable indications for future work targeting the envisaged applications.

3D-Printed Anisotropic Polymer Materials for Functional Applications

Anisotropy is the characteristic of a material to exhibit variations in its mechanical, electrical, thermal, optical properties, etc. along different directions. Anisotropic materials have attracted great research interest because of their wide applications in aerospace, sensing, soft robotics, and tissue engineering. 3D printing provides exceptional advantages in achieving controlled compositions and complex architecture, thereby enabling the manufacture of 3D objects with anisotropic functionalities. Here, a comprehensive review of the recent progress on 3D printing of anisotropic polymer materials based on different techniques including material extrusion, vat photopolymerization, powder bed fusion, and sheet lamination is presented. The state-of-the-art strategies implemented in manipulating anisotropic structures are highlighted with the discussion of material categories, functionalities, and potential applications. This review is concluded with analyzing the current challenges and providing perspectives for further development in this field.

3D-Printed Strong Dental Crown with Multi-Scale Ordered Architecture, High-Precision, and Bioactivity

Mimicking the multi-scale highly ordered hydroxyapatite (HAp) nanocrystal structure of the natural tooth enamel remains a great challenge. Herein, a bottom-up step-by-step strategy is developed using extrusion-based 3D printing technology to achieve a high-precision dental crown with multi-scale highly ordered HAp structure. In this study, hybrid resin-based composites (RBCs) with "supergravity +" HAp nanorods can be printed smoothly via direct ink writing (DIW) 3D printing, induced by shear force through a custom-built nozzle with a gradually shrinking channel. The theoretical simulation results of finite element method are consistent with the experimental results. The HAp nanorods are first highly oriented along a programmable printing direction in a single printed fiber, then arranged in a layer by adjusting the printing path, and finally 3D printed into a highly ordered and complex crown structure. The printed samples with criss-crossed layers by interrupting crack propagation exhibit a flexural strength of 134.1 ± 3.9 MPa and a compressive strength of 361.6 ± 8.9 MPa, which are superior to the corresponding values of traditional molding counterparts. The HAp-monodispersed RBCs are successfully used to print strong and bioactive dental crowns with a printing accuracy of 95%. This new approach can help provide customized components for the clinical restoration of teeth.

Advances in Field-Assisted 3D Printing of Bio-Inspired Composites: From Bioprototyping to Manufacturing

Biocomposite systems evolve to superior structural strategies in adapting to their living environments, using limited materials to form functionality superior to their inherent properties. The synergy of physical-field and Three-dimensional （3D） printing technologies creates unprecedented opportunities that overcome the limitations of traditional manufacturing methods and enable the precise replication of bio-enhanced structures. Here, an overview of typical structural designs in biocomposite systems, their functions and properties, are provided and the recent advances in bio-inspired composites using mechanical, electrical, magnetic, and ultrasound-field-assisted 3D printing techniques are highlighted. Finally, in order to realize the preparation of bionic functional devices and equipment with more superior functions, here an outlook on the development of field-assisted 3D printing technology from three aspects are provided: Materials, technology, and post-processing.

3D Printing-Enabled Nanoparticle Alignment: A Review of Mechanisms and Applications

3D printing (additive manufacturing (AM)) has enormous potential for rapid tooling and mass production due to its design flexibility and significant reduction of the timeline from design to manufacturing. The current state-of-the-art in 3D printing focuses on material manufacturability and engineering applications. However, there still exists the bottleneck of low printing resolution and processing rates, especially when nanomaterials need tailorable orders at different scales. An interesting phenomenon is the preferential alignment of nanoparticles that enhance material properties. Therefore, this review emphasizes the landscape of nanoparticle alignment in the context of 3D printing. Herein, a brief overview of 3D printing is provided, followed by a comprehensive summary of the 3D printing-enabled nanoparticle alignment in well-established and in-house customized 3D printing mechanisms that can lead to selective deposition and preferential orientation of nanoparticles. Subsequently, it is listed that typical applications that utilized the properties of ordered nanoparticles (e.g., structural composites, heat conductors, chemo-resistive sensors, engineered surfaces, tissue scaffolds, and actuators based on structural and functional property improvement). This review's emphasis is on the particle alignment methodology and the performance of composites incorporating aligned nanoparticles. In the end, significant limitations of current 3D printing techniques are identified together with future perspectives.

Fused Filament Fabrication Process: A Review of Numerical Simulation Techniques

Three-dimensional printing (3DP), also known as additive manufacturing (AM), has rapidly evolved over the past few decades. Researchers around the globe have been putting their efforts into AM processes improvement and materials development. One of the most widely used extrusion-based technology under AM processes is Fused Deposition Modeling (FDM), also known as Fused Filament Fabrication (FFF). Numerical simulation tools are being employed to predict the FFF process complexities and material behavior. These tools allow exploring candidate materials for their potential use in the FFF process and process improvements. The prime objective of this study is to provide a comprehensive review of state-of-the-art scientific achievements in numerical simulations of the FFF process for polymers and their composites. The first section presents an in-depth discussion of the FFF process’s physical phenomena and highlights the multi-level complexity. The subsequent section discusses the research efforts, specifically on numerical simulation techniques reported in the literature for simulation of the FFF process. Finally, conclusions are drawn based on the reviewed literature, and future research directions are identified.

Radical photoinitiation with LEDs and applications in the 3D printing of composites

Radical initiation upon LED light irradiation is discussed herein as well as its application in additive manufacturing. The ability of manufacturing complex structures, freedom of design, low energy consumption, fast prototyping, and excellent spatial resolution are the main benefits of the 3D printing technology by photopolymerization. Therefore, the 3D printing of composites through photopolymerization processes is developing rapidly in the academia and industry, and has been a turning point of additive manufacturing (AM). In the present review, an overview of radical initiation with LEDs (i.e., the photopolymerization LED technology, the photoinitiating systems, and the polymerizable media) and of the main 3D printing methods by photopolymerization, materials, and their applications in different fields has been carried out. As a challenging topic, the issue of light penetration in a filled matrix for the access to composites is discussed, including the light transmittance of the composite, the mismatch of the refractive index between the filler and the monomer, the factors of the filler, and the adverse influence of low light penetration on the 3D printing process. In particular, the popular applications of 3D printing by photopolymerization in biomedical science, electronic industry, materials for adsorption, and 4D printing are discussed. Overall, this review gives an overview of the 3D printing of polymer matrix composites through photopolymerization processes as a benchmark for future research and development.

Silk fibroin nanofibers: a promising ink additive for extrusion three-dimensional bioprinting

Here, we investigated the usefulness of silk fibroin nanofibers obtained via mechanical grinding of degummed silkworm silk fibers as an additive in bioinks for extrusion three-dimensional (3D) bioprinting of cell-laden constructs. The nanofibers could be sterilized by autoclaving, and addition of the nanofibers improved the shear thinning of polymeric aqueous solutions, independent of electric charge and the content of cross-linkable moieties in the polymers. The addition of nanofibers to bioinks resulted in the fabrication of hydrogel constructs with higher fidelity to blueprints. Mammalian cells in the constructs showed >85% viability independent of the presence of nanofibers. The nanofibers did not affect the morphologies of enclosed cells. These results demonstrate the great potential of silk fibroin nanofibers obtained via mechanical grinding of degummed silkworm silk fibers as an additive in bioinks for extrusion 3D bioprinting.

Scalable Alignment and Selective Deposition of Nanoparticles for Multifunctional Sensor Applications

Here reported is the layer-by-layer-based advanced manufacturing that yields a simple, novel, and cost-effective technique for generating selective nanoparticle deposition and orientation in the form of well-controlled patterns. The surface roughness of the three-dimensionally printed patterns and the solid-liquid-air contact line, as well as the nanoparticle interactions in dipped suspensions, determine the carbon nanofiber (CNF) alignment, while the presence of triangular grooves supports the pinning of the meniscus, resulting in a configuration consisting of alternating CNF and polymer channels. The polymer/nanoparticle composites show 10 times lower resistance along with the particle alignment direction than the randomly distributed CNF networks and 6 orders of magnitude lower than that along the transverse direction. The unidirectional alignment of the CNF also demonstrates linear piezoresistivity behavior under small strain deformation along with high sensitivity and selectivity toward volatile organic compounds. The reported advanced manufacturing shows broad applications in microelectronics, energy transport, light composites, and multifunctional sensors.

Nanomaterial Patterning in 3D Printing

The synergistic integration of nanomaterials with 3D printing technologies can enable the creation of architecture and devices with an unprecedented level of functional integration. In particular, a multiscale 3D printing approach can seamlessly interweave nanomaterials with diverse classes of materials to impart, program, or modulate a wide range of functional properties in an otherwise passive 3D printed object. However, achieving such multiscale integration is challenging as it requires the ability to pattern, organize, or assemble nanomaterials in a 3D printing process. This review highlights the latest advances in the integration of nanomaterials with 3D printing, achieved by leveraging mechanical, electrical, magnetic, optical, or thermal phenomena. Ultimately, it is envisioned that such approaches can enable the creation of multifunctional constructs and devices that cannot be fabricated with conventional manufacturing approaches.

Stereolithography 3D Printing of Lignin-Reinforced Composites with Enhanced Mechanical Properties

Due to the availability, biodegradability, and biological effects, lignin has emerged as an interesting alternative to petroleum-based compounds for developing sustainable chemicals, materials, and composites. In this study, lignin at various concentrations was incorporated into methacrylate resin via solution blending to fabricate lignin-reinforced composites using stereolithography apparatus three-dimensional printing. Softwood kraft lignin in the amounts of 0.2, 0.4, 0.5, 0.8, and 1.0 wt % in the methacrylate resin was used as a printing ink, and the gel contents and relative contents of the residual resin in the printed samples with various lignin concentrations were measured. The effects of the lignin on the ultimate mechanical properties of the non-postcured and postcured printed composites were determined. The tensile testing results revealed that the incorporation of lignin in the composite increased the tensile strength by 46-64% and Young's modulus by 13-37% for the postcured printed composites compared with that of the control sample (no lignin added). Employing a 0.4 wt % softwood kraft lignin, the tensile strength of the postcured printed composite reached the highest value of 49.0 MPa, which was a 60% increase in comparison to that of the control sample with 30.7 MPa. Scanning electron microscopy images of the fracture samples illustrated that the lignin-incorporated composites exhibited a rougher fracture surface that can presumably dissipate the stress, which could be a contributing factor for the mechanical enhancement.

Recent Progress in Biomimetic Additive Manufacturing Technology: From Materials to Functional Structures

Nature has developed high-performance materials and structures over millions of years of evolution and provides valuable sources of inspiration for the design of next-generation structural materials, given the variety of excellent mechanical, hydrodynamic, optical, and electrical properties. Biomimicry, by learning from nature's concepts and design principles, is driving a paradigm shift in modern materials science and technology. However, the complicated structural architectures in nature far exceed the capability of traditional design and fabrication technologies, which hinders the progress of biomimetic study and its usage in engineering systems. Additive manufacturing (three-dimensional (3D) printing) has created new opportunities for manipulating and mimicking the intrinsically multiscale, multimaterial, and multifunctional structures in nature. Here, an overview of recent developments in 3D printing of biomimetic reinforced mechanics, shape changing, and hydrodynamic structures, as well as optical and electrical devices is provided. The inspirations are from various creatures such as nacre, lobster claw, pine cone, flowers, octopus, butterfly wing, fly eye, etc., and various 3D-printing technologies are discussed. Future opportunities for the development of biomimetic 3D-printing technology to fabricate next-generation functional materials and structures in mechanical, electrical, optical, and biomedical engineering are also outlined.

Shear-Induced Alignment of Anisotropic Nanoparticles in a Single-Droplet Oscillatory Microfluidic Platform

Flow-induced alignment of shape-anisotropic colloidal particles is of great importance in fundamental research and in the fabrication of structurally anisotropic materials; however, rheo-optical studies of shear-induced particle orientation are time- and labor-intensive and require complicated experimental setups. We report a single-droplet oscillatory microfluidic strategy integrated with in-line polarized light imaging as a strategy for studies of shear-induced alignment of rod-shape nanoparticles. Using an oscillating droplet of an aqueous isotropic suspension of cellulose nanocrystals (CNCs), we explore the effect of the shear rate and suspension viscosity on the flow-induced CNC alignment and subsequent relaxation to the isotropic state. The proposed microfluidic strategy enables high-throughput studies of shear-induced orientations in structured liquid under precisely controlled experimental conditions. The results of such studies can be used in the development of structure-anisotropic materials.

Short fiber reinforced 3d printed ceramic composite with shear induced alignment

This paper accounts for utilization of shear induced alignment method during ceramic stereolithography. Lateral oscillation mechanism, combined with 3d printed wall pattern, was employed to generate necessary shear to align fiber in desired direction. First, semicircular channel pattern was printed to assess the effect of difference between wall direction and oscillation direction on the fiber alignment. Then, flexural strength of ceramic matrix was tested with nickel coated carbon fiber and ceramic fiber reinforcements. The results demonstrated that the shear induced alignment further improves the flexural strength compare to randomly distributed samples. Flexural strength of aligned samples with 1.0 wt% carbon fiber loading was improved by ~90% compared to randomly orientated samples and by ~333% compared to unreinforced samples. Finally, fracture surface morphology of the flexural strength test specimens was evaluated. The main fracture mechanism was observed as fiber pull-out.