1
|
Gangwar L, Phatak SS, Etheridge M, Bischof JC. A guide to successful mL to L scale vitrification and rewarming. CRYO LETTERS 2022; 43:316-321. [PMID: 36629824 PMCID: PMC10217567] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Subscribe] [Scholar Register] [Indexed: 01/12/2023]
Abstract
Cryopreservation by vitrification to achieve an "ice free" glassy state is an effective technique for preserving biomaterials including cells, tissues, and potentially even whole organs. The major challenges in cooling to and rewarming from a vitrified state remain ice crystallization and cracking/fracture. Ice crystallization can be inhibited by the use of cryoprotective agents (CPAs), though the inhibition further depends upon the rates achieved during cooling and rewarming. The minimal rate required to prevent any ice crystallization or recrystallization/devitrification in a given CPA is called the critical cooling rate (CCR) or critical warming rate (CWR), respectively. On the other hand, physical cracking is mainly related to thermomechanical stresses, which can be avoided by maintaining temperature differences below a critical threshold. In this simplified analysis, we calculate deltaT as the largest temperature difference occurring in a system during cooling or rewarming in the brittle/glassy phase. This deltaT is then used in a simple "thermal shock equation" to estimate thermal stress within the material to decide if the material is above the yield strength and to evaluate the potential for fracture failure. In this review we aimed to understand the limits of success and failure at different length scales for cryopreservation by vitrification, due to both ice crystallization and cracking. Here we use thermal modeling to help us understand the magnitude and trajectory of these challenges as we scale the biomaterial volume for a given CPA from the milliliter to liter scale. First, we solved the governing heat transfer equations in a cylindrical geometry for three common vitrification cocktails (i.e., VS55, DP6, and M22) to estimate the cooling and warming rates during convective cooling and warming and nanowarming (volumetric heating). Second, we estimated the temperature difference deltaT and compared it to a tolerable threshold (deltaTmax) based on a simplified "thermal shock" equation for the same cooling and rewarming conditions. We found, not surprisingly, that M22 achieves vitrification more easily during convective cooling and rewarming for all volumes compared to VS55 or DP6 due to its considerably lower CCR and CWR. Further, convective rewarming (boundary rewarming) leads to larger temperature differences and smaller rates compared to nanowarming (volumetric rewarming) for all CPAs with increasing failure at larger volumes. We conclude that as more and larger systems are vitrified and rewarmed with standard CPA cocktails, this work can serve as a practical guide to successful implementation based on the characteristic length (volume/surface area) of the system and the specific conditions of cooling and warming. doi.org/10.54680/fr22610110112.
Collapse
Affiliation(s)
- L Gangwar
- Department of Mechanical Engineering, University of Minnesota, Minneapolis, MN, 55455 USA
| | - S S Phatak
- Department of Mechanical Engineering, University of Minnesota, Minneapolis, MN, 55455 USA
| | - M Etheridge
- Department of Mechanical Engineering, University of Minnesota, Minneapolis, MN, 55455 USA
| | - J C Bischof
- Department of Mechanical Engineering; Department of Biomedical Engineering, University of Minnesota, Minneapolis, MN, 55455 USA.
| |
Collapse
|
2
|
Zhan L, Han Z, Shao Q, Etheridge ML, Hays T, Bischof JC. Rapid joule heating improves vitrification based cryopreservation. Nat Commun 2022; 13:6017. [PMID: 36224179 PMCID: PMC9556611 DOI: 10.1038/s41467-022-33546-9] [Citation(s) in RCA: 10] [Impact Index Per Article: 5.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/30/2022] [Accepted: 09/21/2022] [Indexed: 01/24/2023] Open
Abstract
Cryopreservation by vitrification has far-reaching implications. However, rewarming techniques that are rapid and scalable (both in throughput and biosystem size) for low concentrations of cryoprotective agent (CPA) for reduced toxicity are lacking, limiting the potential for translation. Here, we introduce a joule heating-based platform technology, whereby biosystems are rapidly rewarmed by contact with an electrical conductor that is fed a voltage pulse. We demonstrate successful cryopreservation of three model biosystems with thicknesses across three orders of magnitude, including adherent cells (~4 µm), Drosophila melanogaster embryos (~50 µm) and rat kidney slices (~1.2 mm) using low CPA concentrations (2-4 M). Using tunable voltage pulse widths from 10 µs to 100 ms, numerical simulation predicts that warming rates from 5 × 104 to 6 × 108 °C/min can be achieved. Altogether, our results present a general solution to the cryopreservation of a broad spectrum of cellular, organismal and tissue-based biosystems.
Collapse
Affiliation(s)
- Li Zhan
- Department of Mechanical Engineering, University of Minnesota, Minneapolis, MN, USA.
- Center for Engineering in Medicine, Massachusetts General Hospital, Shriners Hospital for Children, Harvard Medical School, Boston, MA, USA.
| | - Zonghu Han
- Department of Mechanical Engineering, University of Minnesota, Minneapolis, MN, USA
| | - Qi Shao
- Department of Mechanical Engineering, University of Minnesota, Minneapolis, MN, USA
| | - Michael L Etheridge
- Department of Mechanical Engineering, University of Minnesota, Minneapolis, MN, USA
| | - Thomas Hays
- Department of Genetics, Cell Biology and Development, University of Minnesota, Minneapolis, MN, USA
| | - John C Bischof
- Department of Mechanical Engineering, University of Minnesota, Minneapolis, MN, USA.
- Department of Biomedical Engineering, University of Minnesota, Minneapolis, MN, USA.
| |
Collapse
|
3
|
Gao Z, Namsrai B, Han Z, Joshi P, Rao JS, Ravikumar V, Sharma A, Ring HL, Idiyatullin D, Magnuson EC, Iaizzo PA, Tolkacheva EG, Garwood M, Rabin Y, Etheridge M, Finger EB, Bischof JC. Vitrification and Rewarming of Magnetic Nanoparticle-Loaded Rat Hearts. ADVANCED MATERIALS TECHNOLOGIES 2022; 7:2100873. [PMID: 35668819 PMCID: PMC9164386 DOI: 10.1002/admt.202100873] [Citation(s) in RCA: 17] [Impact Index Per Article: 8.5] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 07/16/2021] [Indexed: 05/24/2023]
Abstract
To extend the preservation of donor hearts beyond the current 4-6 h, this paper explores heart cryopreservation by vitrification-cryogenic storage in a glass-like state. While organ vitrification is made possible by using cryoprotective agents (CPA) that inhibit ice during cooling, failure occurs during convective rewarming due to slow and non-uniform rewarming which causes ice crystallization and/or cracking. Here an alternative, "nanowarming", which uses silica-coated iron oxide nanoparticles (sIONPs) perfusion loaded through the vasculature is explored, that allows a radiofrequency coil to rewarm the organ quickly and uniformly to avoid convective failures. Nanowarming has been applied to cells and tissues, and a proof of principle study suggests it is possible in the heart, but proper physical and biological characterization especially in organs is still lacking. Here, using a rat heart model, controlled machine perfusion loading and unloading of CPA and sIONPs, cooling to a vitrified state, and fast and uniform nanowarming without crystallization or cracking is demonstrated. Further, nanowarmed hearts maintain histologic appearance and endothelial integrity superior to convective rewarming and indistinguishable from CPA load/unload control hearts while showing some promising organ-level (electrical) functional activity. This work demonstrates physically successful heart vitrification and nanowarming and that biological outcomes can be expected to improve by reducing or eliminating CPA toxicity during loading and unloading.
Collapse
Affiliation(s)
- Zhe Gao
- Department of Mechanical Engineering, University of Minnesota, 111 Church St. SE., Minneapolis, MN 55455, USA
| | - Baterdene Namsrai
- Department of Surgery, University of Minnesota, 420 Delaware Street SE, Minneapolis, MN 55455, USA
| | - Zonghu Han
- Department of Mechanical Engineering, University of Minnesota, 111 Church St. SE., Minneapolis, MN 55455, USA
| | - Purva Joshi
- Department of Mechanical Engineering, Carnegie Mellon University, 5000 Forbes Avenue, Pittsburgh, PA 15213, USA
| | - Joseph Sushil Rao
- Department of Surgery, University of Minnesota, 420 Delaware Street SE, Minneapolis, MN 55455, USA
| | - Vasanth Ravikumar
- Department of Biomedical Engineering, University of Minnesota, 312 Church St. SE, Minneapolis, MN 55455, USA
| | - Anirudh Sharma
- Department of Mechanical Engineering, University of Minnesota, 111 Church St. SE., Minneapolis, MN 55455, USA
| | - Hattie L Ring
- Center for Magnetic Resonance Research, Department of Radiology, University of Minnesota, 2021 6th Street S.E. Minneapolis, Minneapolis, MN 55455, USA
| | - Djaudat Idiyatullin
- Center for Magnetic Resonance Research, Department of Radiology, University of Minnesota, 2021 6th Street S.E. Minneapolis, Minneapolis, MN 55455, USA
| | - Elliott C Magnuson
- Department of Mechanical Engineering, University of Minnesota, 111 Church St. SE., Minneapolis, MN 55455, USA
| | - Paul A Iaizzo
- Department of Surgery, University of Minnesota, 420 Delaware Street SE, Minneapolis, MN 55455, USA
| | - Elena G Tolkacheva
- Department of Biomedical Engineering, University of Minnesota, 312 Church St. SE, Minneapolis, MN 55455, USA
| | - Michael Garwood
- Center for Magnetic Resonance Research, Department of Radiology, University of Minnesota, 2021 6th Street S.E. Minneapolis, Minneapolis, MN 55455, USA
| | - Yoed Rabin
- Department of Mechanical Engineering, Carnegie Mellon University, 5000 Forbes Avenue, Pittsburgh, PA 15213, USA
| | - Michael Etheridge
- Department of Mechanical Engineering, University of Minnesota, 111 Church St. SE., Minneapolis, MN 55455, USA
| | - Erik B Finger
- Department of Surgery, University of Minnesota, 420 Delaware Street SE, Minneapolis, MN 55455, USA
| | - John C Bischof
- Department of Mechanical Engineering, University of Minnesota, 111 Church St. SE., Minneapolis, MN 55455, USA
| |
Collapse
|
4
|
Pasek-Allen JL, Wilharm RK, Gao Z, Pierre VC, Bischof JC. Phosphonate coating of commercial iron oxide nanoparticles for nanowarming cryopreserved samples. J Mater Chem B 2022; 10:3734-3746. [PMID: 35466332 PMCID: PMC9116443 DOI: 10.1039/d1tb02483c] [Citation(s) in RCA: 4] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/02/2023]
Abstract
New preservation technologies may allow for organ banking similar to blood and biomaterial banking approaches. Using cryoprotective agents (CPAs), aqueous solutions with organic components such as DMSO, propylene glycol, and added salts and sugars, organs can be used to vitrify and store organs at −140 °C. When needed, these organs can be rewarmed in a rapid and uniform manner if CPAs are supplemented with iron oxide nanoparticles (IONPs) in an applied radiofrequency field. Speed and uniformity of warming are both IONP concentration and CPA suspension dependent. Here we present a coating method of small molecule phosphonate linker (PLink) and biocompatible polymer (i.e. polyethylene glycol PEG) that tunes stability and increases the maximum allowable concentration of IONPs in CPA suspension. PLink contains a phosphonate 'anchor' for high irreversible binding to iron oxide and a carboxylic acid 'handle' for ligand attachment. PLink-PEG removes and replaces the initial coating layer of commercially available IONPs (EMG1200 (hydrophobic) and EMG308 (hydrophilic) Ferrotec, Inc., increasing colloidal stability and decreasing aggregation in both water and CPAs, (verified with dynamic light scattering) from minutes (uncoated) to up to 6 days. Heating properties of EMG1200, specific absorption rate (SAR), measured using an applied field of 360 kHz and 20 kA m−1, increased from 20 to 180 W per g Fe with increasing PLink-PEG5000. PEG replacing the initially hydrophobic coating decreased aggregation in water and CPA, consistent with earlier studies on heating performance. Furthermore, although the size is minimized at 0.20 mol PEG per g Fe, heating is not maximized until concentrations above 0.43 mol PEG per g Fe on EMG1200. SAR on hydrophilic EMG308 was preserved at 400 W per g Fe regardless of the amount of PLink added to the core. Herein concentrations of IONP in VS55 (common CPA) significantly above our previous capabilities, sIONP at 10 mg Fe per mL, was reached, 25 mg Fe per mL of 308-PEG5000 and 60 mg Fe per mL of 1200-PEG5000, approaching stock EMG308 in water, 60 mg Fe per mL. Furthermore, at these concentrations cryopreserved Human dermal fibroblast cells were successfully nanowarmed (at applied fields described above), with higher viability as compared to convective rewarming in a water bath and heating rate close to 200 °C min−1, 2.5 times faster than our current system. Using PLink as the coating method allowed for higher concentrations of IONPs to be successfully suspended in CPA without affecting the heating ability. Additionally, the model ligand, PEG, allowed for increased stability over time in nanowarming experiments. New preservation technologies may allow for organ banking similar to blood and biomaterial banking approaches.![]()
Collapse
Affiliation(s)
- Jacqueline L. Pasek-Allen
- Department of Biomedical Engineering, University of Minnesota, 312 Church St. SE, Minneapolis, MN 55455, USA
| | - Randall K. Wilharm
- Department of Chemistry, University of Minnesota, 207 Pleasant St SE, Minneapolis, MN 55455, USA
| | - Zhe Gao
- Mechanical Engineering, University of Minnesota, 111 Church Street Se, Minneapolis, MN 55455, USA
| | - Valerie C. Pierre
- Department of Chemistry, University of Minnesota, 207 Pleasant St SE, Minneapolis, MN 55455, USA
| | - John C. Bischof
- Department of Biomedical Engineering, University of Minnesota, 312 Church St. SE, Minneapolis, MN 55455, USA
- Mechanical Engineering, University of Minnesota, 111 Church Street Se, Minneapolis, MN 55455, USA
| |
Collapse
|
5
|
Han Z, Sharma A, Gao Z, Carlson TW, O’Sullivan MG, Finger EB, Bischof JC. Diffusion Limited Cryopreservation of Tissue with Radiofrequency Heated Metal Forms. Adv Healthc Mater 2020; 9:e2000796. [PMID: 32875732 PMCID: PMC7879698 DOI: 10.1002/adhm.202000796] [Citation(s) in RCA: 13] [Impact Index Per Article: 3.3] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 05/11/2020] [Revised: 07/15/2020] [Indexed: 01/25/2023]
Abstract
Cryopreserved tissues are increasingly needed in biomedical applications. However, successful cryopreservation is generally only reported for thin tissues (≤1 mm). This work presents several innovations to reduce cryoprotectant (CPA) toxicity and improve tissue cryopreservation, including 1) improved tissue warming rates through radiofrequency metal form and field optimization and 2) an experimentally verified predictive model to optimize CPA loading and rewarming to reduce toxicity. CPA loading is studied by microcomputed tomography (µCT) imaging, rewarming by thermal measurements, and modeling, and viability is measured after loading and/or cryopreservation by alamarBlue and histology. Loading conditions for three common CPA cocktails (6, 8.4, and 9.3 m) are designed, and then fast cooling and metal forms rewarming (up to 2000 °C min-1 ) achieve ≥90% viability in cryopreserved 1-2 mm arteries with various CPAs. Despite high viability by alamarBlue, histology shows subtle changes after cryopreservation suggesting some degree of cell damage especially in the central portions of thicker arteries up to 2 mm. While further studies are needed, these results show careful CPA loading and higher metal forms warming rates can help reduce CPA loading toxicity and improve outcomes from cryopreservation in tissues while also offering new protocols to preserve larger tissues ≥1 mm in thickness.
Collapse
Affiliation(s)
- Zonghu Han
- Department of Mechanical Engineering, University of Minnesota, 111 Church St. Minneapolis, MN, 55455, USA
| | - Anirudh Sharma
- Department of Mechanical Engineering, University of Minnesota, 111 Church St. Minneapolis, MN, 55455, USA
| | - Zhe Gao
- Department of Mechanical Engineering, University of Minnesota, 111 Church St. Minneapolis, MN, 55455, USA
| | - Timothy W. Carlson
- Department of Veterinary Population Medicine, Comparative Pathology Shared Resource, Masonic Cancer Center, University of Minnesota, 1988 Fitch Avenue, Saint Paul, MN 55108, USA
| | - M. Gerard O’Sullivan
- Department of Veterinary Population Medicine, Comparative Pathology Shared Resource, Masonic Cancer Center, University of Minnesota, 1988 Fitch Avenue, Saint Paul, MN 55108, USA
| | - Erik B. Finger
- Department of Surgery, University of Minnesota, 420 Delaware Street SE, Minneapolis, MN 55455, USA
| | - John C. Bischof
- Department of Mechanical Engineering, Department of Biomedical Engineering, University of Minnesota, 111 Church St. Minneapolis, MN, 55455, USA
| |
Collapse
|
6
|
Liu K, Xu Y, Yu H. Research on Ice Crystal Growth Inside the Vitrified Vs55 with Magnetic Nanoparticles During Devitrification by Cryomicroscopy. Chem Res Chin Univ 2019. [DOI: 10.1007/s40242-019-8230-6] [Citation(s) in RCA: 4] [Impact Index Per Article: 0.8] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/26/2023]
|
7
|
Phatak S, Natesan H, Choi J, Brockbank KG, Bischof JC. Measurement of Specific Heat and Crystallization in VS55, DP6, and M22 Cryoprotectant Systems With and Without Sucrose. Biopreserv Biobank 2018; 16:270-277. [DOI: 10.1089/bio.2018.0006] [Citation(s) in RCA: 10] [Impact Index Per Article: 1.7] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/12/2022] Open
Affiliation(s)
- Shaunak Phatak
- Department of Mechanical Engineering, University of Minnesota, Minneapolis, Minnesota
| | - Harishankar Natesan
- Department of Mechanical Engineering, University of Minnesota, Minneapolis, Minnesota
| | - Jeunghwan Choi
- Department of Engineering, East Carolina University, Greenville, North Carolina
| | - Kelvin G.M. Brockbank
- Department of Bioengineering, Clemson University, South Carolina
- Tissue Testing Technologies, Charleston, South Carolina
| | - John C. Bischof
- Department of Mechanical Engineering, University of Minnesota, Minneapolis, Minnesota
- Biomedical Engineering, University of Minnesota, Minneapolis, Minnesota
| |
Collapse
|
8
|
Manuchehrabadi N, Shi M, Roy P, Han Z, Qiu J, Xu F, Lu TJ, Bischof J. Ultrarapid Inductive Rewarming of Vitrified Biomaterials with Thin Metal Forms. Ann Biomed Eng 2018; 46:1857-1869. [PMID: 29922954 PMCID: PMC6208886 DOI: 10.1007/s10439-018-2063-1] [Citation(s) in RCA: 19] [Impact Index Per Article: 3.2] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 01/31/2018] [Accepted: 05/25/2018] [Indexed: 11/27/2022]
Abstract
Arteries with 1-mm thick walls can be successfully vitrified by loading cryoprotective agents (CPAs) such as VS55 (8.4 M) or less concentrated DP6 (6 M) and cooling at or beyond their critical cooling rates of 2.5 and 40 °C/min, respectively. Successful warming from this vitrified state, however, can be challenging. For example, convective warming by simple warm-bath immersion achieves 70 °C/min, which is faster than VS55's critical warming rate of 55 °C/min, but remains far below that of DP6 (185 °C/min). Here we present a new method that can dramatically increase the warming rates within either a solution or tissue by inductively warming commercially available metal components placed within solutions or in proximity to tissues with non-invasive radiofrequency fields (360 kHz, 20 kA/m). Directly measured warming rates within solutions exceeded 1000 °C/min with specific absorption rates (W/g) of 100, 450 and 1000 for copper foam, aluminum foil, and nitinol mesh, respectively. As proof of principle, a carotid artery diffusively loaded with VS55 and DP6 CPA was successfully warmed with high viability using aluminum foil, while standard convection failed for the DP6 loaded tissue. Modeling suggests this approach can improve warming in tissues up to 4-mm thick where diffusive loading of CPA may be incomplete. Finally, this technology is not dependent on the size of the system and should therefore scale up where convection cannot.
Collapse
Affiliation(s)
- Navid Manuchehrabadi
- Department of Mechanical Engineering, University of Minnesota, 111 Church Street SE, Minneapolis, MN, 55455, USA
- Department of Biomedical Engineering, University of Minnesota, 111 Church Street SE, Minneapolis, MN, 55455, USA
| | - Meng Shi
- School of Energy and Power Engineering, Xi'an Jiaotong University, Xi'an, 710049, People's Republic of China
- Bioinspired Engineering and Biomechanics Center (BEBC), Xi'an Jiaotong University, Xi'an, 710049, People's Republic of China
| | - Priyatanu Roy
- Department of Mechanical Engineering, University of Minnesota, 111 Church Street SE, Minneapolis, MN, 55455, USA
| | - Zonghu Han
- Department of Mechanical Engineering, University of Minnesota, 111 Church Street SE, Minneapolis, MN, 55455, USA
| | - Jinbin Qiu
- Bioinspired Engineering and Biomechanics Center (BEBC), Xi'an Jiaotong University, Xi'an, 710049, People's Republic of China
- The Key Laboratory of Biomedical Information Engineering of Ministry of Education, School of Life Science and Technology, Xi'an Jiaotong University, Xi'an, 710049, People's Republic of China
| | - Feng Xu
- Bioinspired Engineering and Biomechanics Center (BEBC), Xi'an Jiaotong University, Xi'an, 710049, People's Republic of China
- The Key Laboratory of Biomedical Information Engineering of Ministry of Education, School of Life Science and Technology, Xi'an Jiaotong University, Xi'an, 710049, People's Republic of China
| | - Tian Jian Lu
- Bioinspired Engineering and Biomechanics Center (BEBC), Xi'an Jiaotong University, Xi'an, 710049, People's Republic of China.
- State Key Laboratory for Strength and Vibration of Mechanical Structures, School of Aerospace, Xi'an Jiaotong University, Xi'an, 710049, People's Republic of China.
| | - John Bischof
- Department of Mechanical Engineering, University of Minnesota, 111 Church Street SE, Minneapolis, MN, 55455, USA.
- Department of Biomedical Engineering, University of Minnesota, 111 Church Street SE, Minneapolis, MN, 55455, USA.
| |
Collapse
|
9
|
Manuchehrabadi N, Gao Z, Zhang J, Ring HL, Shao Q, Liu F, McDermott M, Fok A, Rabin Y, Brockbank KGM, Garwood M, Haynes CL, Bischof JC. Improved tissue cryopreservation using inductive heating of magnetic nanoparticles. Sci Transl Med 2017; 9:9/379/eaah4586. [PMID: 28251904 DOI: 10.1126/scitranslmed.aah4586] [Citation(s) in RCA: 169] [Impact Index Per Article: 24.1] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/30/2016] [Revised: 11/17/2016] [Accepted: 02/09/2017] [Indexed: 12/15/2022]
Abstract
Vitrification, a kinetic process of liquid solidification into glass, poses many potential benefits for tissue cryopreservation including indefinite storage, banking, and facilitation of tissue matching for transplantation. To date, however, successful rewarming of tissues vitrified in VS55, a cryoprotectant solution, can only be achieved by convective warming of small volumes on the order of 1 ml. Successful rewarming requires both uniform and fast rates to reduce thermal mechanical stress and cracks, and to prevent rewarming phase crystallization. We present a scalable nanowarming technology for 1- to 80-ml samples using radiofrequency-excited mesoporous silica-coated iron oxide nanoparticles in VS55. Advanced imaging including sweep imaging with Fourier transform and microcomputed tomography was used to verify loading and unloading of VS55 and nanoparticles and successful vitrification of porcine arteries. Nanowarming was then used to demonstrate uniform and rapid rewarming at >130°C/min in both physical (1 to 80 ml) and biological systems including human dermal fibroblast cells, porcine arteries and porcine aortic heart valve leaflet tissues (1 to 50 ml). Nanowarming yielded viability that matched control and/or exceeded gold standard convective warming in 1- to 50-ml systems, and improved viability compared to slow-warmed (crystallized) samples. Last, biomechanical testing displayed no significant biomechanical property changes in blood vessel length or elastic modulus after nanowarming compared to untreated fresh control porcine arteries. In aggregate, these results demonstrate new physical and biological evidence that nanowarming can improve the outcome of vitrified cryogenic storage of tissues in larger sample volumes.
Collapse
Affiliation(s)
- Navid Manuchehrabadi
- Department of Mechanical Engineering, University of Minnesota, Minneapolis, MN 55455, USA.,Department of Biomedical Engineering, University of Minnesota, Minneapolis, MN 55455, USA
| | - Zhe Gao
- Department of Mechanical Engineering, University of Minnesota, Minneapolis, MN 55455, USA.,Department of Chemistry, University of Minnesota, Minneapolis, MN 55455, USA
| | - Jinjin Zhang
- Center for Magnetic Resonance Research, University of Minnesota, Minneapolis, MN 55455, USA
| | - Hattie L Ring
- Department of Chemistry, University of Minnesota, Minneapolis, MN 55455, USA.,Center for Magnetic Resonance Research, University of Minnesota, Minneapolis, MN 55455, USA
| | - Qi Shao
- Department of Mechanical Engineering, University of Minnesota, Minneapolis, MN 55455, USA.,Department of Biomedical Engineering, University of Minnesota, Minneapolis, MN 55455, USA
| | - Feng Liu
- Department of Mechanical Engineering, University of Minnesota, Minneapolis, MN 55455, USA
| | - Michael McDermott
- Department of Chemistry, University of Minnesota, Minneapolis, MN 55455, USA
| | - Alex Fok
- Minnesota Dental Research Center for Biomaterials and Biomechanics, University of Minnesota, Minneapolis, MN 55455, USA
| | - Yoed Rabin
- Department of Mechanical Engineering, Carnegie Mellon University, Pittsburgh, PA 15213, USA
| | - Kelvin G M Brockbank
- Department of Bioengineering, Clemson University, Clemson, SC 29634, USA.,Tissue Testing Technologies LLC, North Charleston, SC 29406, USA
| | - Michael Garwood
- Center for Magnetic Resonance Research, University of Minnesota, Minneapolis, MN 55455, USA.,Department of Radiology, University of Minnesota, Minneapolis, MN 55455, USA
| | - Christy L Haynes
- Department of Chemistry, University of Minnesota, Minneapolis, MN 55455, USA
| | - John C Bischof
- Department of Mechanical Engineering, University of Minnesota, Minneapolis, MN 55455, USA. .,Department of Biomedical Engineering, University of Minnesota, Minneapolis, MN 55455, USA
| |
Collapse
|
10
|
Feig JSG, Eisenberg DP, Rabin Y. Polarized light scanning cryomacroscopy, part I: Experimental apparatus and observations of vitrification, crystallization, and photoelasticity effects. Cryobiology 2016; 73:261-71. [PMID: 27343138 PMCID: PMC5420075 DOI: 10.1016/j.cryobiol.2016.06.005] [Citation(s) in RCA: 7] [Impact Index Per Article: 0.9] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/26/2016] [Revised: 06/15/2016] [Accepted: 06/20/2016] [Indexed: 11/26/2022]
Abstract
Cryomacroscopy is an effective means to observe physical events affecting cryopreservation success in large-size specimens. The current study aims at integrating polarized-light in the study of large-size cryopreservation, using the scanning cryomacroscope as a development platform. Results of this study demonstrate polarized light as a visualization enhancement means, including the following effects: contaminants in the CPA solution, crystallization, fracture formation, thermal contraction, and solute precipitation. In addition, photoelasticity effects are used to demonstrate the development of residual stresses and the potential for stress relaxation above the glass transition temperature. Furthermore, this study suggests that the ability to periodically switch between non-polarized light and polarized light is an essential feature of investigation. When using polarized light for example, a dark region may represent a free-of-stress and free-of-crystals material, or fully crystallized material, which may potentially experience mechanical stress; switching to a non-polarized light would help to distinguish between the different cases. The analysis of thermo-mechanical stress in cryopreservation is essentially based on four key elements: identification of physical events, knowledge of physical properties, thermal analysis of the specimen, and description of the mechanical behavior of the cryopreserved material (also known as the constitutive law). With the above knowledge, one can investigate the conditions to preserve structural integrity. While the current study aims at identification of physical events, critical knowledge on physical properties and mechanical behavior has already been developed in previous studies. The companion manuscript (Part II) aims at providing means for thermal analysis in the specimen, which will serve as the basis for a multi-scale analysis of thermo-mechanical stress in large-size specimens.
Collapse
Affiliation(s)
- Justin S G Feig
- Biothermal Technology Laboratory, Department of Mechanical Engineering, Carnegie Mellon University, Pittsburgh, PA, 15213, United States.
| | - David P Eisenberg
- Biothermal Technology Laboratory, Department of Mechanical Engineering, Carnegie Mellon University, Pittsburgh, PA, 15213, United States.
| | - Yoed Rabin
- Biothermal Technology Laboratory, Department of Mechanical Engineering, Carnegie Mellon University, Pittsburgh, PA, 15213, United States.
| |
Collapse
|
11
|
Eisenberg DP, Bischof JC, Rabin Y. Thermomechanical Stress in Cryopreservation Via Vitrification With Nanoparticle Heating as a Stress-Moderating Effect. J Biomech Eng 2016; 138:2473569. [PMID: 26592974 DOI: 10.1115/1.4032053] [Citation(s) in RCA: 26] [Impact Index Per Article: 3.3] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 07/12/2015] [Indexed: 11/08/2022]
Abstract
This study focuses on thermomechanical effects in cryopreservation associated with a novel approach of volumetric heating by means on nanoparticles in an alternating electromagnetic field. This approach is studied for the application of cryopreservation by vitrification, where the crystalline phase is completely avoided-the cornerstone of cryoinjury. Vitrification can be achieved by quickly cooling the material to cryogenic storage, where ice cannot form. Vitrification can be maintained at the end of the cryogenic protocol by quickly rewarming the material back to room temperature. The magnitude of the rewarming rates necessary to maintain vitrification is much higher than the magnitude of the cooling rates that are required to achieve it in the first place. The most common approach to achieve the required cooling and rewarming rates is by exposing the specimen's surface to a temperature-controlled environment. Due to the underlying principles of heat transfer, there is a size limit in the case of surface heating beyond which crystallization cannot be prevented at the center of the specimen. Furthermore, due to the underlying principles of solid mechanics, there is a size limit beyond which thermal expansion in the specimen can lead to structural damage and fractures. Volumetric heating during the rewarming phase of the cryogenic protocol can alleviate these size limitations. This study suggests that volumetric heating can reduce thermomechanical stress, when combined with an appropriate design of the thermal protocol. Without such design, this study suggests that the level of stress may still lead to structural damage even when volumetric heating is applied. This study proposes strategies to harness nanoparticles heating in order to reduce thermomechanical stress in cryopreservation by vitrification.
Collapse
|
12
|
Abstract
Application of the original vitrification protocol used for pieces of heart valves to intact heart valves has evolved over time. Ice-free cryopreservation by Protocol 1 using VS55 is limited to small samples where relatively rapid cooling and warming rates are possible. VS55 cryopreservation typically provides extracellular matrix preservation with approximately 80 % cell viability and tissue function compared with fresh untreated tissues. In contrast, ice-free cryopreservation using VS83, Protocols 2 and 3, has several advantages over conventional cryopreservation methods and VS55 preservation, including long-term preservation capability at -80 °C; better matrix preservation than freezing with retention of material properties; very low cell viability, reducing the risks of an immune reaction in vivo; reduced risks of microbial contamination associated with use of liquid nitrogen; improved in vivo functions; no significant recipient allogeneic immune response; simplified manufacturing process; increased operator safety because liquid nitrogen is not used; and reduced manufacturing costs.
Collapse
Affiliation(s)
- Kelvin G M Brockbank
- Cell & Tissue Systems, Inc., 2231 Technical Parkway, Suite A, North Charleston, SC, 29406, USA,
| | | | | | | |
Collapse
|
13
|
Feig JSG, Rabin Y. The Scanning Cryomacroscope - A Device Prototype for the Study of Cryopreservation. CRYOGENICS 2014; 62:118-128. [PMID: 25484372 PMCID: PMC4250936 DOI: 10.1016/j.cryogenics.2014.04.017] [Citation(s) in RCA: 9] [Impact Index Per Article: 0.9] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 05/31/2023]
Abstract
A new cryomacroscope prototype-a visualization device for the in situ analysis of cryopreserved biological samples-is presented in the current study. In order to visualize samples larger than the field of view of the optical setup, a scanning mechanism is integrated into the system, which represents a key improvement over previous cryomacroscope prototypes. Another key feature of the new design is in its compatibility with available top-loading controlled-rate cooling chambers, which eliminates the need for a dedicated cooling mechanism. The objective for the current development is to create means to generate a single digital movie of an experimental investigation, with all relevant data overlaid. The visualization capabilities of the scanning cryomacroscope are demonstrated in the current study on the cryoprotective agent dimethyl sulfoxide and the cryoprotective cocktail DP6. Demonstrated effects include glass formation, various regimes of crystallization, thermal contraction, and fracture formation.
Collapse
Affiliation(s)
- Justin S G Feig
- Biothermal Technology Laboratory, Department of Mechanical Engineering, Carnegie Mellon University, Pittsburgh PA - 15213, United States
| | - Yoed Rabin
- Biothermal Technology Laboratory, Department of Mechanical Engineering, Carnegie Mellon University, Pittsburgh PA - 15213, United States
| |
Collapse
|
14
|
Seawright A, Ozcelikkale A, Dutton C, Han B. Role of cells in freezing-induced cell-fluid-matrix interactions within engineered tissues. J Biomech Eng 2014; 135:91001. [PMID: 23719856 DOI: 10.1115/1.4024571] [Citation(s) in RCA: 7] [Impact Index Per Article: 0.7] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/19/2012] [Accepted: 05/16/2013] [Indexed: 01/09/2023]
Abstract
During cryopreservation, ice forms in the extracellular space resulting in freezing-induced deformation of the tissue, which can be detrimental to the extracellular matrix (ECM) microstructure. Meanwhile, cells dehydrate through an osmotically driven process as the intracellular water is transported to the extracellular space, increasing the volume of fluid for freezing. Therefore, this study examines the effects of cellular presence on tissue deformation and investigates the significance of intracellular water transport and cell-ECM interactions in freezing-induced cell-fluid-matrix interactions. Freezing-induced deformation characteristics were examined through cell image deformetry (CID) measurements of collagenous engineered tissues embedded with different concentrations of MCF7 breast cancer cells versus microspheres as their osmotically inactive counterparts. Additionally, the development of a biophysical model relates the freezing-induced expansion of the tissue due to the cellular water transport and the extracellular freezing thermodynamics for further verification. The magnitude of the freezing-induced dilatation was found to be not affected by the cellular water transport for the cell concentrations considered; however, the deformation patterns for different cell concentrations were different suggesting that cell-matrix interactions may have an effect. It was, therefore, determined that intracellular water transport during freezing was insignificant at the current experimental cell concentrations; however, it may be significant at concentrations similar to native tissue. Finally, the cell-matrix interactions provided mechanical support on the ECM to minimize the expansion regions in the tissues during freezing.
Collapse
Affiliation(s)
- Angela Seawright
- School of Mechanical Engineering, Purdue University, West Lafayette, IN 47907, USA
| | | | | | | |
Collapse
|
15
|
Ghosh S, Craig Dutton J, Han B. Measurement of spatiotemporal intracellular deformation of cells adhered to collagen matrix during freezing of biomaterials. J Biomech Eng 2013; 136:021025. [PMID: 24317364 DOI: 10.1115/1.4026180] [Citation(s) in RCA: 4] [Impact Index Per Article: 0.4] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 09/15/2013] [Accepted: 12/09/2013] [Indexed: 01/24/2023]
Abstract
Preservation of structural integrity inside cells and at cell-extracellular matrix (ECM) interfaces is a key challenge during freezing of biomaterials. Since the post-thaw functionality of cells depends on the extent of change in the cytoskeletal structure caused by complex cell-ECM adhesion, spatiotemporal deformation inside the cell was measured using a newly developed microbead-mediated particle tracking deformetry (PTD) technique using fibroblast-seeded dermal equivalents as a model tissue. Fibronectin-coated 500 nm diameter microbeads were internalized in cells, and the microbead-labeled cells were used to prepare engineered tissue with type I collagen matrices. After a 24 h incubation the engineered tissues were directionally frozen, and the cells were imaged during the process. The microbeads were tracked, and spatiotemporal deformation inside the cells was computed from the tracking data using the PTD method. Effects of particle size on the deformation measurement method were tested, and it was found that microbeads represent cell deformation to acceptable accuracy. The results showed complex spatiotemporal deformation patterns in the cells. Large deformation in the cells and detachments of cells from the ECM were observed. At the cellular scale, variable directionality of the deformation was found in contrast to the one-dimensional deformation pattern observed at the tissue scale, as found from earlier studies. In summary, this method can quantify the spatiotemporal deformation in cells and can be correlated to the freezing-induced change in the structure of cytosplasm and of the cell-ECM interface. As a broader application, this method may be used to compute deformation of cells in the ECM environment for physiological processes, namely cell migration, stem cell differentiation, vasculogenesis, and cancer metastasis, which have relevance to quantify mechanotransduction.
Collapse
|
16
|
Rabin Y, Taylor MJ, Feig JSG, Baicu S, Chen Z. A new cryomacroscope device (Type III) for visualization of physical events in cryopreservation with applications to vitrification and synthetic ice modulators. Cryobiology 2013; 67:264-73. [PMID: 23993920 DOI: 10.1016/j.cryobiol.2013.08.005] [Citation(s) in RCA: 9] [Impact Index Per Article: 0.8] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/22/2013] [Revised: 08/15/2013] [Accepted: 08/15/2013] [Indexed: 10/26/2022]
Abstract
The objective of the current study is to develop a new cryomacroscope prototype for the study of vitrification in large-size specimens. The unique contribution in the current study is in developing a cryomacroscope setup as an add-on device to a commercial controlled-rate cooler and in demonstration of physical events in cryoprotective cocktails containing synthetic ice modulators (SIM)-compounds which hinder ice crystal growth. Cryopreservation by vitrification is a highly complex application, where the likelihood of crystallization, fracture formation, degradation of the biomaterial quality, and other physical events are dependent not only upon the instantaneous cryogenic conditions, but more significantly upon the evolution of conditions along the cryogenic protocol. Nevertheless, cryopreservation success is most frequently assessed by evaluating the cryopreserved product at its end states-either at the cryogenic storage temperature or room temperature. The cryomacroscope is the only available device for visualization of large-size specimens along the thermal protocol, in an effort to correlate the quality of the cryopreserved product with physical events. Compared with earlier cryomacroscope prototypes, the new Cryomacroscope-III evaluated here benefits from a higher resolution color camera, improved illumination, digital recording capabilities, and high repeatability in tested thermal conditions via a commercial controlled-rate cooler. A specialized software package was developed in the current study, having two modes of operation: (a) experimentation mode to control the operation of the camera, record camera frames sequentially, log thermal data from sensors, and save case-specific information; and (b) post-processing mode to generate a compact file integrating images, elapsed time, and thermal data for each experiment. The benefits of the Cryomacroscope-III are demonstrated using various tested mixtures of SIMs with the cryoprotective cocktail DP6, which were found effective in preventing ice growth, even at significantly subcritical cooling rates with reference to the pure DP6.
Collapse
Affiliation(s)
- Yoed Rabin
- Biothermal Technology Laboratory, Carnegie Mellon University, Pittsburgh, PA, United States.
| | | | | | | | | |
Collapse
|
17
|
He X. Thermostability of biological systems: fundamentals, challenges, and quantification. Open Biomed Eng J 2011; 5:47-73. [PMID: 21769301 PMCID: PMC3137158 DOI: 10.2174/1874120701105010047] [Citation(s) in RCA: 64] [Impact Index Per Article: 4.9] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 11/08/2010] [Revised: 01/31/2011] [Accepted: 02/01/2011] [Indexed: 12/25/2022] Open
Abstract
This review examines the fundamentals and challenges in engineering/understanding the thermostability of biological systems over a wide temperature range (from the cryogenic to hyperthermic regimen). Applications of the bio-thermostability engineering to either destroy unwanted or stabilize useful biologicals for the treatment of diseases in modern medicine are first introduced. Studies on the biological responses to cryogenic and hyperthermic temperatures for the various applications are reviewed to understand the mechanism of thermal (both cryo and hyperthermic) injury and its quantification at the molecular, cellular and tissue/organ levels. Methods for quantifying the thermophysical processes of the various applications are then summarized accounting for the effect of blood perfusion, metabolism, water transport across cell plasma membrane, and phase transition (both equilibrium and non-equilibrium such as ice formation and glass transition) of water. The review concludes with a summary of the status quo and future perspectives in engineering the thermostability of biological systems.
Collapse
Affiliation(s)
- Xiaoming He
- Multiscale Biothermostability Engineering Laboratory, Department of Mechanical Engineering and Biomedical Engineering Program, University of South Carolina, 300 Main Street, Columbia, SC 29208, USA
| |
Collapse
|
18
|
Taylor MJ, Baicu S. Review of vitreous islet cryopreservation: Some practical issues and their resolution. Organogenesis 2009; 5:155-66. [PMID: 20046679 PMCID: PMC2781096 DOI: 10.4161/org.5.3.9812] [Citation(s) in RCA: 37] [Impact Index Per Article: 2.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 07/21/2009] [Accepted: 08/14/2009] [Indexed: 11/19/2022] Open
Abstract
Transplantation of pancreatic islets for the treatment of diabetes mellitus is widely anticipated to eventually provide a cure once a means for preventing rejection is found without reliance upon global immunosuppression. Long-term storage of islets is crucial for the organization of transplantation, islet banking, tissue matching, organ sharing, immuno-manipulation and multiple donor transplantation. Existing methods of cryopreservation involving freezing are known to be suboptimal providing only about 50% survival. The development of techniques for ice-free cryopreservation of mammalian tissues using both natural and synthetic ice blocking molecules, and the process of vitrification (formation of a glass as opposed to crystalline ice) has been a focus of research during recent years. These approaches have established in other tissues that vitrification can markedly improve survival by circumventing ice-induced injury. Here we review some of the underlying issues that impact the vitrification approach to islet cryopreservation and describe some initial studies to apply these new technologies to the long-term storage of pancreatic islets. These studies were designed to optimize both the pre-vitrification hypothermic exposure conditions using newly developed media and to compare new techniques for ice-free cryopreservation with conventional freezing protocols. Some practical constraints and feasible resolutions are discussed. Eventually the optimized techniques will be applied to clinical allografts and xenografts or genetically-modified islets designed to overcome immune responses in the diabetic host.
Collapse
|
19
|
Abstract
Vitrification is a process in which a liquid begins to behave as a solid during cooling without any substantial change in molecular arrangement or thermodynamic state variables. The physical phenomenon of vitrification is relevant to both cryopreservation by freezing, in which cells survive in glass between ice crystals, and cryopreservation by vitrification in which a whole sample is vitrified. The change from liquid to solid behavior is called the glass transition. It is coincident with liquid viscosity reaching 10(13) Poise during cooling, which corresponds to a shear stress relaxation time of several minutes. The glass transition can be understood on a molecular level as a loss of rotational and translational degrees of freedom over a particular measurement timescale, leaving only bond vibration within a fixed molecular structure. Reduced freedom of molecular movement results in decreased heat capacity and thermal expansivity in glass relative to the liquid state. In cryoprotectant solutions, the change from liquid to solid properties happens over a approximately 10 degrees C temperature interval centered on a glass transition temperature, typically near -120 degrees C (+/-10 degrees C) for solutions used for vitrification. Loss of freedom to quickly rearrange molecular position causes liquids to depart from thermodynamic equilibrium as they turn into a glass during vitrification. Residual molecular mobility below the glass transition temperature allows glass to very slowly contract, release heat, and decrease entropy during relaxation toward equilibrium. Although diffusion is practically non-existent below the glass transition temperature, small local movements of molecules related to relaxation have consequences for cryobiology. In particular, ice nucleation in supercooled vitrification solutions occurs at remarkable speed until at least 15 degrees C below the glass transition temperature.
Collapse
Affiliation(s)
- Brian Wowk
- 21st Century Medicine, Inc., 14960 Hilton Drive, Fontana, CA 92336, USA.
| |
Collapse
|
20
|
Cryopreservation of carotid artery segments via vitrification subject to marginal thermal conditions: correlation of freezing visualization with functional recovery. Cryobiology 2008; 57:1-8. [PMID: 18490009 DOI: 10.1016/j.cryobiol.2008.03.002] [Citation(s) in RCA: 27] [Impact Index Per Article: 1.7] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 01/24/2008] [Accepted: 03/20/2008] [Indexed: 11/21/2022]
Abstract
Cryopreservation is a well-established technique for long-term storage of viable cells and tissues. However, in recent years, application of established cryobiological principles to the preservation of multicellular tissues and organs has demanded considerable attention to ways of circumventing the deleterious effects of ice and thermal stresses in bulky tissues. As part of a multidisciplinary research program designed to study the interactions of thermo-physical events with tissue preservation, we report here on the implementation of a slow cooling (3 degrees C/min) and slow warming (62 degrees C/min) regimen towards scale-up of vitreous preservation of large tissue samples. Specifically, the correlation of thermo-physical events during vitrification of carotid artery segments with function recovery is reported using marginal thermal conditions for achieving vitrification in bulky samples. Moreover, the outcome is compared with a similar study reported previously using a 3-fold higher rate of rewarming (186+/-13 degrees C/min). Tissue vitrification using an 8.4M cryoprotectant cocktail solution (VS55) was achieved in 1 ml samples by imposing a low (2.6+/-0.1 degrees C/min) cooling rate, between -40 degrees C and -100 degrees C, and a low rewarming rate (62+/-4 degrees C/min) between -100 degrees C and -40 degrees C. Following cryoprotectant removal, the artery segments were cut into 3-4mm rings for function testing on a contractility apparatus by measuring isometric responses to four agonist and antagonists (norepinephrine, phenylepinephrine, calcium ionophore and sodium nitroprusside). In addition, non-specific metabolic function of the vessel rings was determined using the REDOX indicator alamarBlue. Contractile function, normalized to untreated control samples, in response to the agonists norepinephrine and phenylepinephrine was significantly better in the slowly rewarmed group of carotid segments (74+/-9% and 62+/-11%, respectively) than for the more rapidly warmed group 31+/-7% and 45+/-15%, respectively). However, EC(50) sensitivities were not significantly different between the groups. Thermo-physical events such as ice formation and fractures were monitored throughout the cooling and warming phases using cryomacroscopy with the aid of a purpose-built borescope device. This technique allowed a direct observation of the visual impact of ice formation on specific zones along the blood vessel segment where, in most cases, no ice formation or fractures were observed in the vicinity of the artery segments. However, in specific instances when some ice crystallization was observed to impact the artery segment, the subsequent testing of function revealed a total loss of contractility. The successful vitrification of blood vessel segments using marginal conditions of slow cooling and rewarming, provide essential information for the development of scale-up protocols that is necessary when clinically relevant size samples need to be cryopreserved in an essentially ice-free state. This information can further be integrated into computer simulations of heat transfer and thermo-mechanical stress, where the slowest cooling rate anywhere in the simulated domain must exceed the critical values identified in the current study.
Collapse
|
21
|
Jimenez Rios JL, Steif PS, Rabin Y. Stress-strain measurements and viscoelastic response of blood vessels cryopreserved by vitrification. Ann Biomed Eng 2007; 35:2077-86. [PMID: 17828592 PMCID: PMC2613250 DOI: 10.1007/s10439-007-9372-0] [Citation(s) in RCA: 21] [Impact Index Per Article: 1.2] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/03/2007] [Accepted: 08/14/2007] [Indexed: 10/22/2022]
Abstract
To gain increased insight into thermo-mechanical phenomena during cryopreservation, tensile stress relaxation experiments were conducted on vitrified blood vessels (vitreous in Latin means Glassy), and the results compared with various viscoelastic models. Using a recently presented device, isothermal stress-relaxation results were obtained for a bovine carotid artery model, permeated with the cryoprotectant cocktail VS55 and a reference solution of 7.05 M DMSO. After a rapidly applied tensile strain, experimental results display exponential decay of stress with time; the stress at a given time increases with decreasing specimen temperature. Among the viscoelastic models investigated, the Williams-Landel-Ferry model was found to best-fit the variation of the stress relaxation data with temperature, while a Maxwell-Weichert model is used to represent the exponential decay of the stress with time. Blood vessel properties were found to dominate at temperatures above roughly -100 degrees C, while the properties of the cryoprotectant dominate below this temperature. A suitably defined steady-state viscosity displayed a similar behavior for both cryoprotectants, when normalized with respect to the cryoprotectant glass transition temperature.
Collapse
Affiliation(s)
- Jorge L Jimenez Rios
- Biothermal Technology Laboratory, Department of Mechanical Engineering, Carnegie Mellon University, Pittsburgh, PA 15213, USA.
| | | | | |
Collapse
|
22
|
Jimenez Rios JL, Rabin Y. A New Device for Mechanical Testing of Blood Vessels at Cryogenic Temperatures. EXPERIMENTAL MECHANICS 2007; 47:1741-2765. [PMID: 18958183 PMCID: PMC2574507 DOI: 10.1007/s11340-007-9038-8] [Citation(s) in RCA: 11] [Impact Index Per Article: 0.6] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 11/22/2006] [Accepted: 01/23/2007] [Indexed: 05/27/2023]
Abstract
As part of an ongoing program to study the thermo-mechanical effects associated with cryopreservation via vitrification (vitreous in Latin means glassy), the current study focuses on the development of a new device for mechanical testing of blood vessels at cryogenic temperatures. This device is demonstrated on a bovine carotid artery model, permeated with the cryoprotectant cocktail VS55 and a reference solution of 7.05M DMSO, below glass transition. Results are also presented for crystallized specimens, in the absence of cryoprotectants. Results indicate that the elastic modulus of a specimen with no cryoprotectant, at about -140°C (8.6°C and 15.5°C below the glass transition temperature of 7.05M DMSO and VS55, respectively), is 1038.8 ± 25.2 MPa, which is 8% and 3% higher than that of a vitrified specimen permeated with 7.05M DMSO and VS55, respectively. The elastic modulus of a crystallized material at -50°C is lower by ~20% lower from that at -140°C.
Collapse
Affiliation(s)
| | - Yoed Rabin
- * Corresponding author; ; fax: (412) 268 3348
| |
Collapse
|