Influence of strontium for calcium substitution in bioactive glasses on degradation, ion release and apatite formation

Structural and Dynamical Effects of the CaO/SrO Substitution in Bioactive Glasses

Silicate glasses containing silicon, sodium, phosphorous, and calcium have the ability to promote bone regeneration and biodegrade as new tissue is generated. Recently, it has been suggested that adding SrO can benefit tissue growth and silicate glass dissolution. Motivated by these recent developments, the effect of SrO/CaO-CaO/SrO substitution on the local structure and dynamics of Si-Na-P-Ca-O oxide glasses has been studied in this work. Differential thermal analysis has been performed to determine the thermal stability of the glasses after the addition of strontium. The local structure has been studied by neutron diffraction augmented by Reverse Monte Carlo simulation, and the local dynamics by neutron Compton scattering and Raman spectroscopy. Differential thermal analysis has shown that SrO-containing glasses have lower glass transition, melting, and crystallisation temperatures. Moreover, the addition of the Sr2+ ions decreased the thermal stability of the glass structure. The total neutron diffraction augmented by the RMC simulation revealed that Sr played a similar role as Ca in the glass structure when substituted on a molar basis. The bond length and the coordination number distributions of the network modifiers and network formers did not change when SrO (x = 0.125, 0.25) was substituted for CaO (25-x). However, the network connectivity increased in glass with 12.5 mol% CaO due to the increased length of the Si-O-Si interconnected chain. The analysis of Raman spectra revealed that substituting CaO with SrO in the glass structure dramatically enhances the intensity of the high-frequency band of 1110-2000 cm-1. For all glasses under investigation, the changes in the relative intensities of Raman bands and the distributions of the bond lengths and coordination numbers upon the SrO substitution were correlated with the values of the widths of nuclear momentum distributions of Si, Na, P, Ca, O, and Sr. The widths of nuclear momentum distributions were observed to soften compared to the values observed and simulated in their parent metal-oxide crystals. The widths of nuclear momentum distributions, obtained from fitting the experimental data to neutron Compton spectra, were related to the amount of disorder of effective force constants acting on individual atomic species in the glasses.

Investigation of Osteomyelitis Inducing Methicillin-Resistant Staphylococcus aureus Inhibition Effect by Strontium-Substituted Borate Bioactive Glasses

Borate glass transforms into hydroxycarbonate apatite more rapidly than silicate glass. This research aims to evaluate strontium's structural and biological effects on borate bioactive glass (BBG) and the influence of strontium concentrations (0%, 5%, 10%, and 15% Sr) prepared via the sol-gel method. The study reveals significant findings related to the physicochemical properties of the glass. Immersion of the glass powders in a simulated body fluid (SBF) led to the development of a hydroxyapatite (HAP) layer on the glass surfaces. This transformation was verified through X-ray diffraction (XRD), scanning electron microscopy (SEM), and Fourier transform infrared (FTIR) analyses. In particular, 5% strontium exhibited gradual degradation, resulting in particle sizes below 100 nm. The BBG-15%Sr demonstrates heightened pathogenic activity as it shows a significant inhibition zone of 14 mm at 250 μg/mL, surpassing other substituted BBGs. It effectively combats Gram-positive bacteria, completely inhibiting MRSA growth at 50 μg/mL. This underscores its robust biofilm disruption capabilities, eradicating biofilms, even at minimal concentrations after prolonged exposure. C. elegans when subjected to BBG-15%Sr shows less ROS production when compared with the others. Moreover, the results suggest that the modified glass could be a potential material for the treatment of osteomyelitis-affected bone repair.

Sr-Incorporated Bioactive Glass Remodels the Immunological Microenvironment by Enhancing the Mitochondrial Function of Macrophage via the PI3K/AKT/mTOR Signaling Pathway

The repair of critical-sized bone defects continues to pose a challenge in clinics. Strontium (Sr), recognized for its function in bone metabolism regulation, has shown potential in bone repair. However, the underlying mechanism through which Sr2+ guided favorable osteogenesis by modulating macrophages remains unclear, limiting their application in the design of bone biomaterials. Herein, Sr-incorporated bioactive glass (SrBG) was synthesized for further investigation. The release of Sr ions enhanced the immunomodulatory properties and osteogenic potential by modulating the polarization of macrophages toward the M2 phenotype. In vivo, a 3D-printed SrBG scaffold was fabricated and showed consistently improved bone regeneration by creating a prohealing immunological microenvironment. RNA sequencing was performed to explore the underlying mechanisms. It was found that Sr ions might enhance the mitochondrial function of macrophage by activating PI3K/AKT/mTOR signaling, thereby favoring osteogenesis. Our findings demonstrate the relationship between the immunomodulatory role of Sr ions and the mitochondrial function of macrophages. By focusing on the mitochondrial function of macrophages, Sr2+-mediated immunomodulation sheds light on the future design of biomaterials for tissue regenerative engineering.

The unexplored role of alkali and alkaline earth elements (ALAEs) on the structure, processing, and biological effects of bioactive glasses

Bioactive glass has been employed in several medical applications since its inception in 1969. The compositions of these materials have been investigated extensively with emphasis on glass network formers, therapeutic transition metals, and glass network modifiers. Through these experiments, several commercial and experimental compositions have been developed with varying chemical durability, induced physiological responses, and hydroxyapatite forming abilities. In many of these studies, the concentrations of each alkali and alkaline earth element have been altered to monitor changes in structure and biological response. This review aims to discuss the impact of each alkali and alkaline earth element on the structure, processing, and biological effects of bioactive glass. We explore critical questions regarding these elements from both a glass science and biological perspective. Should elements with little biological impact be included? Are alkali free bioactive glasses more promising for greater biological responses? Does this mixed alkali effect show increased degradation rates and should it be employed for optimized dissolution? Each of these questions along with others are evaluated comprehensively and discussed in the final section where guidance for compositional design is provided.

Effect of strontium fluoride on mechanical and remineralization properties of enamel: An in-vitro study on a modified orthodontic adhesive

OBJECTIVES

Evaluate the ability of strontium fluoride on bond strength and enamel integrity after incorporation within orthodontic adhesive system as a delivery vehicle.

METHODS

Experimental orthodontic adhesive system Transbond™ XT were modified with 1% Sr2+, 0.5% SrF2, 1% strontium, 0.5% Sr2+, 1% F-, 0.5% F-, and no additions were control. Mixing of formulation was monitored using Fourier transform infrared spectroscopy. Small-molecule drug-discovery suite was used to gain insights into Sr2+, F-, and SrF2 binding. Shear bond testing was performed after 6-months of ageing. Enamel blocks were cut, and STEM pictures were recorded. Specimens were indented to evaluate elastic modulus. Raman microscope was used to collect Raman spectra and inspected using a scanning electron microscope. Crystal structural analysis was performed using X-ray diffraction. Effect of material on cellular proliferation was determined. Confocal was performed to evaluate the effect of formulation on biofilms.

RESULTS

FTIR of modified adhesives depicted peak changes within range due to various functional groups existing within samples. TEM represented structurally optimized hexagonal unit-cell of hydroxyapatite. Mean shear bond strength is recorded highest for Transbond XT with 1% SrF2. Dead bacterial percentage appeared higher in 0.5% SrF2 and 1% F- specimens. Crystal lengths showed an increase in 0.5% and 1% SrF2 specimens. Phase contrast within TEM images showed a union of 0.5% SrF2 crystal with enamel crystal with higher elastic modulus and highly mineralized crystalline hydroxyapatite. Intensity of ν1 PO43- and ν1 CO32- along with carbonate - / ν1PO43- ratio displayed good association with strontium fluoride. The formulation showed acceptable cell biocompatibility (p < 0.353). All specimens displayed characteristic diffraction maxima of different apatite angles within XRD.

SIGNIFICANCE

Experimental results suggested good biocompatibility, adequate mechanical strength, and far-ranging crystallization ability. This would provide a new strategy to overcome the two major challenges of fixed orthodontics, biofilm growth, and demineralization of enamel.

Strontium and Zinc Co-Doped Mesoporous Bioactive Glass Nanoparticles for Potential Use in Bone Tissue Engineering Applications

Mesoporous bioactive glass nanoparticles (MBGNs) have attracted significant attention as multifunctional nanocarriers for various applications in both hard and soft tissue engineering. In this study, multifunctional strontium (Sr)- and zinc (Zn)-containing MBGNs were successfully synthesized via the microemulsion-assisted sol-gel method combined with a cationic surfactant (cetyltrimethylammonium bromide, CTAB). Sr-MBGNs, Zn-MBGNs, and Sr-Zn-MBGNs exhibited spherical shapes in the nanoscale range of 100 ± 20 nm with a mesoporous structure. Sr and Zn were co-substituted in MBGNs (60SiO2-40CaO) to induce osteogenic potential and antibacterial properties without altering their size, morphology, negative surface charge, amorphous nature, mesoporous structure, and pore size. The synthesized MBGNs facilitated bioactivity by promoting the formation of an apatite-like layer on the surface of the particles after immersion in Simulated Body Fluid (SBF). The effect of the particles on the metabolic activity of human mesenchymal stem cells was concentration-dependent. The hMSCs exposed to Sr-MBGNs, Zn-MBGNs, and Sr-Zn-MBGNs at 200 μg/mL enhanced calcium deposition and osteogenic differentiation without osteogenic supplements. Moreover, the cellular uptake and internalization of Sr-MBGNs, Zn-MBGNs, and Sr-Zn-MBGNs in hMSCs were observed. These novel particles, which exhibited multiple functionalities, including promoting bone regeneration, delivering therapeutic ions intracellularly, and inhibiting the growth of Staphylococcus aureus and Escherichia coli, are potential nanocarriers for bone regeneration applications.

Chitosan and Sodium Hyaluronate Hydrogels Supplemented with Bioglass for Bone Tissue Engineering

The aim of the study was to produce biocomposites based on chitosan and sodium hyaluronate hydrogels supplemented with bioglasses obtained under different conditions (temperature, time) and to perform an in vitro evaluation of their cytocompatibility using both indirect and direct methods. Furthermore, the release of ions from the composites and the microstructure of the biocomposites before and after incubation in simulated body fluid were assessed. Tests on extracts from bioglasses and hydrogel biocomposites were performed on A549 epithelial cells, while MG63 osteoblast-like cells were tested in direct contact with the developed biomaterials. The immune response induced by the biomaterials was also evaluated. The experiments were carried out on both unstimulated and lipopolysaccharide (LPS) endotoxin-stimulated human peripheral blood cells in the presence of extracts of the biocomposites and their components. Extracts of the materials produced do not exhibit toxic effects on A549 cells, and do not increase the production of proinflammatory cytokines tumour necrosis factor alpha (TNF-α) and interleukin (IL-6) by blood cells in vitro. In direct contact with MG63 osteoblast-like cells, biocomposites containing the reference bioglass and those containing SrO are more cytocompatible than biocomposites with ZnO-doped bioglass. Using two testing approaches, the effects both of the potentially toxic agents released and of the surface of the tested materials on the cell condition were assessed. The results pave the way for the development of highly porous hydrogel-bioglass composite scaffolds for bone tissue engineering.

Synthesis of a Calcium Silicate Cement Containing a Calcinated Strontium Silicate Phase

Objectives

The positive effects of strontium on dental and skeletal remineralization have been confirmed in the literature. This study aimed to assess the properties of a calcium silicate cement (CSC) containing a sintered strontium silicate phase.

Materials and Methods

The calcium silicate and strontium silicate phases were synthesized by the sol-gel technique. Strontium silicate powder in 0 (CSC), 10 (CSC/10Sr), 20 (CSC/20Sr), and 30 (CSC/30Sr) weight percentages was mixed with calcium silicate powder. Calcium chloride was used in the liquid phase. X-ray diffraction (XRD) of specimens was conducted before and after hydration. The setting time and compressive strength were assessed at 1 and 7 days after setting. The set discs of the aforementioned groups were immersed in the simulated body fluid (SBF) for 1 and 7 days. The ion release profile was evaluated by inductively coupled plasma-optical emission spectrometry (ICP-OES). Biomineralization on the specimen surface was evaluated by scanning electron microscopy/energy dispersive X-ray spectroscopy (SEM/EDS). Data were analyzed by the Kolmogorov-Smirnov test, one-way and mixed ANOVA, Levene's test, and LSD post hoc test (P  < 0.05).

Results

Except for an increasement in the peak intensity of hydrated specimens, XRD revealed no other difference in the crystalline phases of hydrated and nonhydrated specimens. The compressive strength was not significantly different at 1 and 7 days in any group (P  > 0.05). The setting time significantly decreased by an increase in percentage of strontium (P  < 0.05). Release of Ca and Si ions significantly decreased by an increase in percentage of strontium (P  < 0.05). SEM/EDS showed the formation of calcium phosphate deposits at 1 and 7 days.

Conclusion

Incorporation of 10-30 wt% sintered strontium silicate phase as premixed in CSC can significantly decrease the setting time without compromising the compressive strength or biomineralization process of the cement.

Influence of Strontium on the Biological Behavior of Bioactive Glasses for Bone Regeneration

Bioactive glasses (BGs) can potentially be applied in biomedicine, mainly for bone repair and replacement, given their unique ability to connect to natural bone tissue and stimulate bone regeneration. Since their discovery, several glass compositions have been developed to improve the properties and clinical abilities of traditional bioactive glass. Different inorganic ions, such as strontium (Sr2+), have been incorporated in BG due to their ability to perform therapeutic functions. Sr2+ has been gaining prominence due to its ability to stimulate osteogenesis, providing an appropriate environment to improve bone regeneration, in addition to its antibacterial potential. However, as there are still points in the literature that are not well consolidated, such as the influence of ionic concentrations and the BG production technique, this review aims to collect information on the state of the art of the biological behavior of BGs containing Sr2+. It also aims to gather data on different types of BGs doped with different concentrations of Sr2+, and to highlight the manufacturing techniques used in order to analyze the influence of the incorporation of this ion for bone regeneration purposes.

Enhancing bone tissue engineering with 3D-Printed polycaprolactone scaffolds integrated with tragacanth gum/bioactive glass

Tissue-engineered bone substitutes, characterized by favorable physicochemical, mechanical, and biological properties, present a promising alternative for addressing bone defects. In this study, we employed an innovative 3D host-guest scaffold model, where the host component served as a mechanical support, while the guest component facilitated osteogenic effects. More specifically, we fabricated a triangular porous polycaprolactone framework (host) using advanced 3D printing techniques, and subsequently filled the framework's pores with tragacanth gum-45S5 bioactive glass as the guest component. Comprehensive assessments were conducted to evaluate the physical, mechanical, and biological properties of the designed scaffolds. Remarkably, successful integration of the guest component within the framework was achieved, resulting in enhanced bioactivity and increased strength. Our findings demonstrated that the scaffolds exhibited ion release (Si, Ca, and P), surface apatite formation, and biodegradation. Additionally, in vitro cell culture assays revealed that the scaffolds demonstrated significant improvements in cell viability, proliferation, and attachment. Significantly, the multi-compartment scaffolds exhibited remarkable osteogenic properties, indicated by a substantial increase in the expression of osteopontin, osteocalcin, and matrix deposition. Based on our results, the framework provided robust mechanical support during the new bone formation process, while the guest component matrix created a conducive micro-environment for cellular adhesion, osteogenic functionality, and matrix production. These multi-compartment scaffolds hold great potential as a viable alternative to autografts and offer promising clinical applications for bone defect repair in the future.

Bioactive Glasses Enriched with Strontium or Zinc with Different Degrees of Structural Order as Components of Chitosan-Based Composite Scaffolds for Bone Tissue Engineering

The development of innovative biomaterials with improved integration with bone tissue and stimulating regeneration processes is necessary. Here, we evaluate the usefulness of bioactive glasses from the SiO2-P2O5-CaO system enriched with 2 wt.% SrO or ZnO in the manufacturing of chitosan-based scaffolds. Bioglasses produced using the sol-gel method were subjected to thermal treatment in different regimes. Chitosan/bioglass composites were produced with a weight ratio. Bioglasses were evaluated via TG-DTA, FTIR, and SEM-EDS before and after incubation in simulated body fluid (SBF). The release of ions was tested. The cytocompatibility of the composites in contact with MG63 osteoblast-like cells was evaluated. The results showed that the presence of the crystalline phase decreased from 41.2-44.8% for nonmodified bioglasses to 24.2-24.3% for those modified with ZnO and 22.0-24.2% for those modified with SrO. The samples released Ca2+, Zn2+, and/or Sr2+ ions and were bioactive according to the SBF test. The highest cytocompatibility was observed for the composites containing nonmodified bioglasses, followed by those enriched with SrO bioglasses. The least cytocompatible were the composites containing ZnO bioglasses that released the highest amount of Zn2+ ions (0.58 ± 0.07 mL/g); however, those that released 0.38 ± 0.04 mL/g were characterised by acceptable cytocompatibility. The study confirmed that it is feasible to control the biological performance of chitosan/bioglass composites by adjusting the composition and heat treatment parameters of bioglasses.

Incorporation of strontium borosilicate bioactive glass in calcium aluminate biocement: Physicomechanical, bioactivity and antimicrobial properties

Strontium borosilicate bioactive glass (SrBG) and calcium aluminate cement (CA) composites have been synthesized. The primary goal of this work is to evaluate how SrBG affects the bioactivity and physico-mechanical characteristics of CA. To fulfill this aim, SrBG was prepared by melt-quenching method and utilized as a substitute for CA by 5, 10, 15, and 20 wt%. To estimate the biological behavior of the prepared specimens, hydrᴏxyapatite layer (HA) establishment on the surface of cement paste was followed; after their immersion in a solution resembles human blood plasma (simulated body fluid solution (SBF)) at a temperature of about37 ± 0.5 °C for 4 weeks. The variations of pH, Ca and P ions concentrations in the SBF solution after soaking were determined. Compressive strength, apparent porosity, and bulk density were also measured. Via Fourier transform IR spectroscopy and X-ray diffraction analyses, the main components had been analyzed. Using scanning electron microscope (SEM) attached to energy dispersive spectroscopy, morphology of the samples was investigated. Additionally, the antimicrobial property was also assessed. The results proved that the hydrᴏxyapatite layer (HA) was developed on the surface of the prepared samples after soaking in the biological solution (SBF). It was also found that increasing SrBG percent in synthesized samples promotes the physico-mechanical characteristics and also the bioactivity performance of CA cement. Finally, these materials also showed good inhibition behavior towards bacterial biᴏfilms, against S. aureus and E. coli. after 48h. This makes these materials excellent candidates for preventing growth of bacteria after their implantation in teeth or bone.

Novel Bioactive Glass/Graphene Oxide-Coated Surgical Sutures for Soft Tissue Regeneration

The combination of a commercially available PGLA (poly[glycolide-co-l-lactide]), 90:10% suture material with bioactive bioglass nanopowders (BGNs) and graphene oxide (GO)-doped BGNs offers new opportunities for the clinical application of biomaterials in soft tissue engineering. In the present experimental work, we demonstrate that GO-doped melt-derived BGNs were synthesized via the sol-gel process. After that, novel GO-doped and undoped BGNs were used to coat resorbable PGLA surgical sutures, thereby imparting bioactivity, biocompatibility, and accelerated wound healing properties to the sutures. Stable and homogeneous coatings on the surface of the sutures were achieved using an optimized vacuum sol deposition method. The phase composition, morphology, elemental characteristics, and chemical structure of uncoated and BGNs- and BGNs/GO-coated suture samples were characterized using Fourier transform infrared spectroscopy, field emission scanning electron microscopy, associated with elemental analysis, and knot performance test. In addition, in vitro bioactivity tests, biochemical tests, and in vivo tests were performed to examine the role of BGNs and GO on the biological and histopathological properties of the coated suture samples. The results indicated that the formation of BGNs and GO was enhanced significantly on the suture surface, which allowed for enhanced fibroblast attachment, migration, and proliferation and promoted the secretion of the angiogenic growth factor to speed up wound healing. These results confirmed the biocompatibility of BGNs- and BGNs/GO-coated suture samples and the positive effect of BGNs on the behavior of L929 fibroblast cells and also showed for the first time the possibility that cells can adhere and proliferate on the BGNs/GO-coated suture samples, especially in an in vivo environment. Resorbable surgical sutures with bioactive coatings, such as those prepared herein, can be an attractive biomaterial not only for hard tissue engineering but also for clinical applications in soft tissue engineering.

Evaluation of biocomposite putty with strontium and zinc co-doped 45S5 bioactive glass and sodium hyaluronate

The application of powder or granule formed bioactive glasses in the defect area with the help of a liquid carrier to fill the defects is a subject of interest and is still open to development. In this study, it was aimed to prepare biocomposites of bioactive glasses incorporating different co-dopants with a carrier biopolymer and to create a fluidic material (Sr and Zn co-doped 45S5 bioactive glasses‑sodium hyaluronate). All biocomposite samples were pseudoplastic fluid type, which may be suitable for defect filling and had excellent bioactivity behaviors confirmed by FTIR, SEM-EDS and XRD. Biocomposites with Sr and Zn co-doped bioactive glass had higher bioactivity considering the crystallinity of hydroxyapatite formations compared to biocomposite with undoped bioactive glasses. Biocomposites with high bioactive glass content had hydroxyapatite formations with higher crystallinity compared to biocomposites with low bioactive glass. Furthermore, all biocomposite samples showed non-cytotoxic effect on the L929 cells up to a certain concentration. However, biocomposites with undoped bioactive glass showed cytotoxic effects at lower concentrations compared to biocomposites with co-doped bioactive glass. Thus, biocomposite putties utilizing Sr and Zn co-doped bioactive glasses may be advantageous for orthopedic applications due to their specified rheological, bioactivity, and biocompatibility properties.

Multifunctional Zn and Ag co-doped bioactive glass nanoparticles for bone therapeutic and regeneration

Bone cancer has traditionally been treated using surgery, radiotherapy, and/or chemotherapy. The nonspecific distribution of chemotherapy and implantable infections are significant risk factors for the failure of the bone to heal. Multifunctional zinc and silver co-doped bioactive glass nanoparticles (yAg-xZn-BGNPs) with a diameter of 150 ± 30 nm were successfully synthesized using modified sol-gel and two-step post-functionalization processes, tailored to provide antibacterial and anticancer activity whilst maintaining osteogenesis ability. Co-doped BGNPs with Zn and Ag did not significantly alter physicochemical properties, including size, morphology, glass network, and amorphous nature. Apatite-like layer was observed on the surface of yAg-xZn-BGNPs and resorbed in the simulated body fluid solution, which could increase their bioactivity. Human fetal osteoblast cell line (hFOB 1.19) treated with particles showed calcified tissue formation and alkaline phosphatase activity in the absence of osteogenic supplements in vitro, especially with 0.5Ag-1Zn-BGNPs. Moreover, these particles preferentially disrupted the metabolic activity of bone cancer cells (MG-63) and had an antibacterial effect against B. subtilis, E. coli, and S. aureus via the disc diffusion method. This novel 0.5Ag-1Zn-BGNP and 1Ag-1Zn-BGNPs, with wide-ranging ability to stimulate bone regeneration, to inhibit bone cancer cell proliferation, and to prevent bacterial growth properties, may provide a feasible strategy for bone cancer treatment. The 0.5Ag-1Zn-BGNPs and 1Ag-1Zn-BGNPs can be applied for the preparation of scaffolds or filler composites using in bone tissue engineering.

Alkaline earth metals for osteogenic scaffolds: From mechanisms to applications

Regeneration of bone defects is a significant challenge today. As alternative approaches to the autologous bone, scaffold materials have remarkable features in treating bone defects; however, the various properties of current scaffold materials still fall short of expectations. Due to the osteogenic capability of alkaline earth metals, their application in scaffold materials has become an effective approach to improving their properties. Furthermore, numerous studies have shown that combining alkaline earth metals leads to better osteogenic properties than applying them alone. In this review, the physicochemical and physiological characteristics of alkaline earth metals are introduced, mainly focusing on their mechanisms and applications in osteogenesis, especially magnesium (Mg), calcium (Ca), strontium (Sr), and barium (Ba). Furthermore, this review highlights the possible cross-talk between pathways when alkaline earth metals are combined. Finally, some of the current drawbacks of scaffold materials are enumerated, such as the high corrosion rate of Mg scaffolds and defects in the mechanical properties of Ca scaffolds. Moreover, a brief perspective is also provided regarding future directions in this field. It is worth exploring that whether the levels of alkaline earth metals in newly regenerated bone differs from those in normal bone. The ideal ratio of each element in the bone tissue engineering scaffolds or the optimal concentration of each elemental ion in the created osteogenic environment still needs further exploration. The review not only summarizes the research developments in osteogenesis but also offers a direction for developing new scaffold materials.

A review on borate bioactive glasses (BBG): effect of doping elements, degradation, and applications

Because of their excellent biologically active qualities, bioactive glasses (BGs) have been extensively used in the biomedical domain, leading to better tissue-implant interactions and promoting bone regeneration and wound healing. Aside from having attractive characteristics, BGs are appealing as a porous scaffold material. On the other hand, such porous scaffolds should enable tissue proliferation and integration with the natural bone and neighboring soft tissues and degrade at a rate that allows for new bone development while preventing bacterial colonization. Therefore, researchers have recently become interested in a different BG composition based on borate (B₂O₃) rather than silicate (SiO₂). Furthermore, apatite synthesis in the borate-based bioactive glass (BBG) is faster than in the silicate-based bioactive glass, which slowly transforms to hydroxyapatite. This low chemical durability of BBG indicates a fast degradation process, which has become a concern for their utilization in biological and biomedical applications. To address these shortcomings, glass network modifiers, active ions, and other materials can be combined with BBG to improve the bioactivity, mechanical, and regenerative properties, including its degradation potential. To this end, this review article will highlight the details of BBGs, including their structure, properties, and medical applications, such as bone regeneration, wound care, and dental/bone implant coatings. Furthermore, the mechanism of BBG surface reaction kinetics and the role of doping ions in controlling the low chemical durability of BBG and its effects on osteogenesis and angiogenesis will be outlined.

3D Printed Osteoblast-Alginate/Collagen Hydrogels Promote Survival, Proliferation and Mineralization at Low Doses of Strontium Calcium Polyphosphate

The generation of biomaterials via 3D printing is an emerging biotechnology with novel methods that seeks to enhance bone regeneration. Alginate and collagen are two commonly used biomaterials for bone tissue engineering and have demonstrated biocompatibility. Strontium (Sr) and Calcium phosphate (CaP) are vital elements of bone and their incorporation in composite materials has shown promising results for skeletal repair. In this study, we investigated strontium calcium polyphosphate (SCPP) doped 3D printed alginate/collagen hydrogels loaded with MC3T3-E1 osteoblasts. These cell-laden scaffolds were crosslinked with different concentrations of 1% SCPP to evaluate the effect of strontium ions on cell behavior and the biomaterial properties of the scaffolds. Through scanning electron microscopy and Raman spectroscopy, we showed that the scaffolds had a granular surface topography with the banding pattern of alginate around 1100 cm^-1 and of collagen around 1430 cm^-1. Our results revealed that 2 mg/mL of SCPP induced the greatest scaffold degradation after 7 days and least amount of swelling after 24 h. Exposure of osteoblasts to SCPP induced severe cytotoxic effects after 1 mg/mL. pH analysis demonstrated acidity in the presence of SCPP at a pH between 2 and 4 at 0.1, 0.3, 0.5, and 1 mg/mL, which can be buffered with cell culture medium. However, when the SCPP was added to the scaffolds, the overall pH increased indicating intrinsic activity of the scaffold to buffer the SCPP. Moreover, cell viability was observed for up to 21 days in scaffolds with early mineralization at 0.3, 0.5, and 1 mg/mL of SCPP. Overall, low doses of SCPP proved to be a potential additive in biomaterial approaches for bone tissue engineering; however, the cytotoxic effects due to its pH must be monitored closely.

Can strontium replace calcium in bioactive materials for dental applications?

The substitution of calcium with strontium in bioactive materials has been promising but there has been some concern over the material instability and possible toxicity. The aim of this research was the synthesis and characterization of calcium and strontium substituted bioactive materials and assessment of interactions with local tissues and peripheral elemental migration in an animal model. A bioactive glass, hydroxyapatite and hydraulic calcium silicate with 50% or 100% calcium substitution with strontium were developed and the set materials were characterized immediately after setting and after 30 and 180-days in solution. Following subcutaneous implantation, the local (tissue histology, elemental migration) and systemic effects (elemental deposition after organ digestion) were assessed. The strontium-replaced silicate cements resulted in the synthesis of partially substituted phases and strontium leaching at all-time points. The strontium silicate implanted in the animal model could not be retrieved in over half of the specimens showing the high rate of material digestion. Tissue histology showed that all materials caused inflammation after 30 days of implantation however this subsided and angiogenesis occurred after 180 days. Strontium was not detected in the local tissues or the peripheral organs while all calcium containing materials caused calcium deposition in the kidneys. The tricalcium silicate caused elemental migration of calcium and silicon in the local tissues shown by the elemental mapping but no deposition of calcium was identified in the peripheral organs verified by the assessment of the digested tissues. Strontium can substitute calcium in bioactive materials without adverse local or systemic effects.

Surface Modification of 3D-Printed PCL/BG Composite Scaffolds via Mussel-Inspired Polydopamine and Effective Antibacterial Coatings for Biomedical Applications

A wide variety of composite scaffolds with unique geometry, porosity and pore size can be fabricated with versatile 3D printing techniques. In this work, we fabricated 3D-printed composite scaffolds of polycaprolactone (PCL) incorporating bioactive glass (BG) particles (13-93 and 13-93B3 compositions) by using fused deposition modeling (FDM). The scaffolds were modified with a "mussel-inspired surface coating" to regulate biological properties. The chemical and surface properties of scaffolds were analyzed by Fourier transform infrared spectroscopy (FTIR), contact angle and scanning electron microscopy (SEM). Polydopamine (PDA) surface-modified composite scaffolds exhibited attractive properties. Firstly, after the surface modification, the adhesion of a composite coating based on gelatin incorporated with strontium-doped mesoporous bioactive glass (Sr-MBGNs/gelatin) was significantly improved. In addition, cell attachment and differentiation were promoted, and the antibacterial properties of the scaffolds were increased. Moreover, the bioactivity of these scaffolds was also significantly influenced: a hydroxyapatite layer formed on the scaffold surface after 3 days of immersion in SBF. Our results suggest that the promoting effect of PDA coating on PCL-BG scaffolds leads to improved scaffolds for bone tissue engineering.

Nanofibrous Hydrogel Nanocomposite Based on Strontium-Doped Bioglass Nanofibers for Bone Tissue Engineering Applications

The main aim of the current study is to fabricate an osteocompatible, bioactive, porous, and degradable bone tissue engineering scaffold. For this purpose, bioactive glasses (BGs) were chosen due to their similarity to bone's natural mineral composition, and the effect of replacing Ca ions with Sr on their properties were considered. First, strontium-containing BGs (Sr-BGs) were synthesized using the electrospinning technique and assembled by the sol-gel method, then they were incorporated into the alginate (Alg) matrix. Photographs of the scanning electron microscope (SEM) showed that the BG nanofibers have a diameter of 220 ± 36 nm, which was smaller than the precursor nanofibers (275 ± 66 nm). The scaffolds possess a porous internal microstructure (230-330 nm pore size) with interconnected pores. We demonstrated that the scaffolds could be degraded in the acetate sodium buffer and phosphate-buffered saline. The osteoactivity of the scaffolds was confirmed via visual inspection of the SEM illustrations after seven days of immersing them in the SBF solution. In vitro assessments disclosed that the produced Alg-based composites including Sr-BGs (Alg/Sr-BGs) are blood-compatible and biocompatible. Accumulating evidence shows that Alg/Sr-BG (5%, 10%, and 15%) hydrogels could be a promising scaffold for bone regeneration.

Physicochemical Properties and Inductive Effect of Calcium Strontium Silicate on the Differentiation of Human Dental Pulp Stem Cells for Vital Pulp Therapies: An In Vitro Study

The development of biomaterials that exhibit profound bioactivity and stimulate stem cell differentiation is imperative for the success and prognosis of vital pulp therapies. The objectives were to (1) synthesize calcium strontium silicate (CSR) ceramic through the sol−gel process (2) investigate its physicochemical properties, bioactivity, cytocompatibility, and its stimulatory effect on the differentiation of human dental pulp stem cells (HDPSC). Calcium silicate (CS) and calcium strontium silicate (CSR) were synthesized by the sol−gel method and characterized by x-ray diffraction (XRD). Setting time, compressive strength, and pH were measured. The in vitro apatite formation was evaluated by SEM-EDX and FTIR. The NIH/3T3 cell viability was assessed using an MTT assay. The differentiation of HDPSC was evaluated using alkaline phosphatase activity (ALP), and Alizarin red staining (ARS). Ion release of Ca, Sr, and Si was measured using inductive coupled plasma optical emission spectroscopy (ICP-OES). XRD showed the synthesis of (CaSrSiO4). The initial and final setting times were significantly shorter in CSR (5 ± 0.75 min, 29 ± 1.9 min) than in CS (8 ± 0.77 min, 31 ± 1.39 min), respectively (p < 0.05). No significant difference in compressive strength was found between CS and CSR (p > 0.05). CSR demonstrated higher apatite formation and cell viability than CS. The ALP activity was significantly higher in CSR 1.16 ± 0.12 than CS 0.92 ± 0.15 after 14 d of culture (p < 0.05). ARS showed higher mineralization in CSR than CS after 14 and 21 d culture times. CSR revealed enhanced differentiation of HDPSC, physicochemical properties, and bioactivity compared to CS.

Rapid Synthesis of Multifunctional Apatite via the Laser-Induced Hydrothermal Process

Synthetic biomaterials are used to overcome the limited quantity of human-derived biomaterials and to impart additional biofunctionality. Although numerous synthetic processes have been developed using various phases and methods, currently commonly used processes have some issues, such as a long process time and difficulties with extensive size control and high-concentration metal ion substitution to achieve additional functionality. Herein, we introduce a rapid synthesis method using a laser-induced hydrothermal process. Based on the thermal interaction between the laser pulses and titanium, which was used as a thermal reservoir, hydroxyapatite particles ranging from nanometer to micrometer scale could be synthesized in seconds. Further, this method enabled selective metal ion substitution into the apatite matrix with a controllable concentration. We calculated the maximum temperature achieved by laser irradiation at the surface of the thermal reservoir based on the validation of three simplification assumptions. Subsequent linear regression analysis showed that laser-induced hydrothermal synthesis follows an Arrhenius chemical reaction. Hydroxyapatite and Mg²⁺-, Sr²⁺-, and Zn²⁺-substituted apatite powders promoted bone cell attachment and proliferation ability due to ion release from the hydroxyapatite and the selective ion-substituted apatite powders, which had a low crystallinity and relatively high solubility. Laser-induced hydrothermal synthesis is expected to become a powerful ceramic material synthesis technology.

In Vivo Evaluation of the Effects of B-Doped Strontium Apatite Nanoparticles Produced by Hydrothermal Method on Bone Repair

In the present study, the structural, morphological, and in vivo biocompatibility of un-doped and boron (B)-doped strontium apatite (SrAp) nanoparticles were investigated. Biomaterials were fabricated using the hydrothermal process. The structural and morphological characterizations of the fabricated nanoparticles were performed by XRD, FT-IR, FE-SEM, and EDX. Their biocompatibility was investigated by placing them in defects in rat tibiae in vivo. The un-doped and B-doped SrAp nanoparticles were successfully fabricated. The produced nanoparticles were in the shape of nano-rods, and the dimensions of the nano-rods decreased as the B ratio increased. It was observed that the structural and morphological properties of strontium apatite nanoparticles were affected by the contribution of B. A stoichiometric Sr/P ratio of 1.67 was reached in the 5% B-doped sample (1.68). The average crystallite sizes were 34.94 nm, 39.70 nm, 44.93 nm, and 48.23 nm in un-doped, 1% B-doped, 5% B-doped, and 10% B-doped samples, respectively. The results of the in vivo experiment revealed that the new bone formation and osteoblast density were higher in the groups with SrAp nanoparticles doped with different concentrations of B than in the control group, in which the open defects were untreated. It was observed that this biocompatibility and the new bone formation were especially elevated in the B groups, which added high levels of strontium were added. The osteoblast density was higher in the group in which the strontium element was placed in the opened bone defect compared with the control group. However, although new bone formation was slightly higher in the strontium group than in the control group, the difference was not statistically significant. Furthermore, the strontium group had the highest amount of fibrotic tissue formation. The produced nanoparticles can be used in dental and orthopedic applications as biomaterials.

Synthesis, Processing and the Effect of Thermal Treatment on the Solubility, Antioxidant Potential and Cytocompatibility of Y2O3 and CeO2 doped SiO2-SrO-Na2O Glass-Ceramics

Thermal treatment of a 0.52SiO₂-0.24SrO-0.24-xNa₂O-xMO glass-ceramic series (where x = 0.08 and MO = Y₂O₃ or CeO₂) was conducted in order to synthesize yttrium (Y³⁺) and cerium (Ce³⁺) crystalline species that may act as radical oxygen specie (ROS) scavengers. The prominent phase for the Control is a sodium-strontium-silicate while the experimental glass-ceramics (HY, YCe, and HCe) present sodium-Y/Ce-silicate and oxide phases. Disk shrinkage during thermal processing ranges from 1-7% for Control, HY, YCe, and HCe in both diameter and thickness. Solubility studies determined that the release of Si⁴⁺ and Na⁺ are greatest from the Control disks which peaks at 1550 µg/mL. Release from the Y³⁺ and Ce³⁺ glass-ceramics reached 320 µg/mL for Si⁴⁺ and 630 µg/mL for Na⁺. The range of antioxidant capacity (ABTS assay) for all samples was 0.31-3.9 mMTE. No significant reduction in MC 3T3 Osteoblast cell viability was observed for any composition tested.

Acellular bioactivity and drug delivery of new strontium doped bioactive glasses prepared through a hydrothermal process

This work aims to study the kinetics of apatite layer formation on the surface of strontium doped binary bioactive glasses (BG: 63S37C) prepared for the first time by a hydrothermal process and evaluate their potential for drug loading and release using ibuprofen (IBU) as an anti-inflammatory drug vector. First, the binary glass 63S37C was doped with various amounts of strontium, from 0.2 to 1 mol%. Subsequently, the amorphous state of the samples and the microstructure were assessed by TGA, XRD, FTIR, ICP-AES, and SEM-EDS. Next, the in vitro bioactivity was evaluated by following the surface morphology and composition changes of soaked samples for up to 14 days at 37 °C in simulated bodily fluid (SBF). Finally, SEM-EDS spectroscopy showed clearly the appearance of needle-shaped apatite on amorphous glass substrates at the earlier stages of immersion for bioglasses doped with strontium. These findings are also confirmed with XRD and FTIR analysis. Furthermore, 63S37C BG proved that the drug release increased with increasing strontium content. Altogether, this novel class of bioactive glasses may be considered to have a promising future for biomedical applications.

In vitro biomineralization potential in simulated wound fluid and antibacterial efficacy of biologically-active glass nanoparticles containing B2O3/ZnO

In the present study, SiO₂-CaO-B₂O₃-ZnO (SCBZ), SiO₂-CaO-B₂O₃ (SCB), SiO₂-CaO-ZnO (SCZ) and SiO₂-CaO (SC) silicate-based glasses were synthesized by the sol-gel method to elucidate the influence of B₂O₃ and ZnO substitution on glass characteristics aiming to further use in wound healing applications. The amorphous nature, spherical-shaped morphology and nano-sized primary particles of glasses were revealed by XRD and SEM analysis. Moreover, investigating the antibacterial activity of glasses against E.coli and S.aureus bacteria indicated the improved antibacterial properties of SCBZ glass against both bacterial strains compared with SCB and SCZ glasses. Assessment of ion release revealed that the incorporation of zinc induces a more stable glass network with a lower tendency to dissolution contrary to the incorporation of boron, which facilitated the dissolution of glass by the formation of more reactive SiOB and BO bonds. Glasses were immersed in Simulated Wound Fluid (SWF) to predict their mineralization susceptibility. Morphological studies and FTIR analysis showed the formation of cauliflower-like hydroxy-carbonated apatite on the surface of SCB and SC glasses after 14 days. In contrast, the presence of Zn in SCBZ and SCZ glasses inhibited the formation of crystalline apatite and induced the deposition of spherical-shaped amorphous apatite. Our study suggests that the co-incorporation of B and Zn in SCBZ glass make this material a potential multifunctional candidate for accelerating the healing of skin wounds.

Strontium- and peptide-modified silicate nanostructures for dual osteogenic and antimicrobial activity

Developing multifunctional nanostructures that promote bone repair while fighting infection is highly desirable in bone regenerative therapies. Previous efforts have focused on achieving one property or another by altering the chemical makeup of nanostructures or using growth factors or antibiotics. We present nanostructures with several simultaneous functional attributes including positive effects of strontium on bone formation and prevention of osteoclast differentiation along with incorporation of antimicrobial peptides (AMP) to prevent infection. To form these multifunctional nanostructures, mesoporous calcium silicate (CaMSN) was modified with high levels of strontium. For this, CaMSNs were either partially substituted (20 wt% Ca) or completely replaced with strontium (Sr) to form Sr-CaMSN or SrMSN. The mesoporous nature of these bioactive silicate nanostructures rendered a configuration for substantial AMP loading as well as their effective delivery. The physico-chemical and structural characterization of synthesized MSNs confirmed the mesoporous nature of the synthesized MSNs and their total surface area, pore size, pore volume and SBF-mediated bioactivity remained unaltered with the incorporation of Sr. However, biological evaluation confirmed that synthesized SrMSN upregulated osteogenic differentiation of mesenchymal stromal cells and significantly downregulated osteoclast differentiation. Also, the AMP-loaded MSNs prevented formation and growth of methicillin resistant Staphylococcus aureus (MRSA) biofilms. Thus, high Sr-containing AMP-loaded SrMSNs may combat MRSA-associated infection while promoting bone regeneration. The controlled availability of therapeutic Sr and AMP release as SrMSN degrade enables its potential application in bone tissue regeneration.

High proportion strontium-doped micro-arc oxidation coatings enhance early osseointegration of titanium in osteoporosis by anti-oxidative stress pathway

The excessive accumulation of reactive oxygen species (ROS) under osteoporosis precipitates a microenvironment with high levels of oxidative stress (OS). This could significantly interfere with the bioactivity of conventional titanium implants, impeding their early osseointegration with bone. We have prepared a series of strontium (Sr)-doped titanium implants via micro-arc oxidation (MAO) to verify their efficacy and differences in osteoinduction capabilities under normal and osteoporotic (high OS levels) conditions. Apart from the chemical composition, all groups exhibited similar physicochemical properties (morphology, roughness, crystal structure, and wettability). Among the groups, the low Sr group (Sr25%) was more conducive to osteogenesis under normal conditions. In contrast, by increasing the catalase (CAT)/superoxide dismutase (SOD) activity and decreasing ROS levels, the high Sr-doped samples (Sr75% and Sr100%) were superior to Sr25% in inducing osteogenic differentiation of MC3T3-E1 cells and the M2 phenotype polarization of RAW264.7 cells, thus enhancing early osseointegration. Furthermore, the results of both in vitro cell co-culture and in vivo studies also showed that the high Sr-doped samples (especially Sr100%) had positive effects on osteoimmunomodulation under the OS microenvironment. Ultimately, the collated findings indicated that the high proportion Sr-doped MAO coatings were more favorable for osteoporosis patients in implant restorations.

•

First study on osteogenic difference of Sr-doped implants in normal and OS conditions.

•

Low Sr-doped MAO coating displays optimal bioactivity in normal microenvironment.

•

High Sr coating significantly enhances osteoimmunomodulation/osteoinduction under OS.

•

High Sr sample resists OS damage by activating CAT/SOD and scavenging excess ROS.

•

High Sr implant restorations are more favorable for osteoporosis patients.

Advances in bioactive glass-containing injectable hydrogel biomaterials for tissue regeneration

Successful tissue regeneration requires a scaffold with tailorable biodegradability, tissue-like mechanical properties, structural similarity to extracellular matrix (ECM), relevant bioactivity, and cytocompatibility. In recent years, injectable hydrogels have spurred increasing attention in translational medicine as a result of their tunable physicochemical properties in response to the surrounding environment. Furthermore, they have the potential to be implanted via minimally invasive procedures while enabling deep penetration, which is considered a feasible alternative to traditional open surgical procedures. However, polymeric hydrogels may lack sufficient stability and bioactivity in physiological environments. Composite hydrogels containing bioactive glass (BG) particulates, synergistically combining the advantages of their constituents, have emerged as multifunctional biomaterials with tailored mechanical properties and biological functionalities. This review paper highlights the recent advances in injectable composite hydrogel systems based on biodegradable polymers and BGs. The influence of BG particle geometry, composition, and concentration on gel formation, rheological and mechanical behavior as well as hydration and biodegradation of injectable hydrogels have been discussed. The applications of these composite hydrogels in tissue engineering are additionally described, with particular attention to bone and skin. Finally, the prospects and current challenges in the development of desirable injectable bioactive hydrogels for tissue regeneration are discussed to outline a roadmap for future research. STATEMENT OF SIGNIFICANCE: Developing a biomaterial that can be readily available for surgery, implantable via minimally invasive procedures, and be able to effectively stimulate tissue regeneration is one of the grand challenges in modern biomedicine. This review summarizes the state-of-the-art of injectable bioactive glass-polymer composite hydrogels to address several challenges in bone and soft tissue repair. The current limitations and the latest evolutions of these composite biomaterials are critically examined, and the roles of design parameters, such as composition, concentration, and size of the bioactive phase, and polymer-glass interactions on the rheological, mechanical, biological, and overall functional performance of hydrogels are detailed. Existing results and new horizons are discussed to provide a state-of-the-art review that may be useful for both experienced and early-stage researchers in the biomaterials community.

Occluding dentin tubules with monetite paste in vitro

OBJECTIVES

This study was performed to evaluate the occlusion of monetite paste on dentine tubule and provide a new potential method for treating dentine hypersensitivity.

METHODS

Calcium oxide, strontium chloride, and polyethylene glycol phosphate were mixed in a certain proportion and ground in a planetary ball mill. The reaction was carried out by adjusting the pH to obtain monetite and hydroxyapatite paste. The morphological characteristics of the paste were observed through scanning electron microscope (SEM). The structure and composition were analyzed through X-ray diffraction (XRD) and Fourier transform infrared spectrometer (FTIR). The extracted third molar was selected to undergo demineralization to establish the in vitro study model of dentin hypersensitivity. The samples were randomly divided into four groups: blank control group (treated with distilled water), casein peptide phosphate-amorphic calcium phosphate (CPP-ACP) group, monetite paste group, and hydroxyapatite paste group. Each group was used to scrub the dentin surface with the corresponding materials for 7 days. The morphological characteristics of the dentin surface and section were observed through SEM, the microhardness of the dentin before and after mineralization was analyzed with a microhardness tester, and the composition of the deposits on the surface of the mineralized samples was examined through XRD.

RESULTS

XRD and FTIR showed that the composition of the paste was mainly monetite, and the composition of hydroxyapatite paste was mainly composed of hydroxyapatite. SEM revealed that the size of the crystal particles of the synthesized paste was tens to hundreds of nanometers. Monetite and hydroxyapatite paste could produce a thicker mineralization layer on the dentin surface, and the mineralization of the dentin tubules of monetite was deeper than that of hydroxyapatite paste. The microhardness of the monetite paste group was significantly less than those of the hydroxyapatite paste groups (P<0.05).

CONCLUSIONS

Monetite paste could effectively block the exposed dentin tubules and be used for treating dentin hypersensitivity.

Enamel Remineralization Competence of a Novel Fluoride-Incorporated Bioactive Glass Toothpaste-A Surface Micro-Hardness, Profilometric, and Micro-Computed Tomographic Analysis

This study aimed to analyze the enamel remineralization efficacy of a novel fluoridated bioactive glass (F-BG) toothpaste compared to a standard fluoride toothpaste. Seventy-two enamel blocks (N = 72) were divided into groups of twenty-four blocks according to the toothpaste exposure—group 1: brushed with distilled water, group 2: brushed with fluoride toothpaste (Colgate^TM), and group 3: brushed with F-BG toothpaste (BioMinF^TM). Pre-brushing, enamel blocks were demineralized using 6 wt.% citric acid (pH = 2.4). Tooth brushing was performed using a mixture of respective toothpaste and artificial saliva (AS), and each enamel block received 5000 linear strokes. The samples were assessed for surface micro-hardness (to estimate Vickers hardness number, VHN), surface roughness (Ra), and volume loss/gain using micro-computed tomography (micro-CT). The highest increase in the VHN was noticed for group 3 (117.81) followed by group 2 (61.13), and all the intragroup comparisons were statistically significant (p < 0.05). Demineralization increased the Ra values, and a decrease was observed post-remineralization for all the groups. The maximum Ra decrease was observed for group 3 (−223.2 nm) followed by group 2 (−55.6 nm), and all the intragroup comparisons were again statistically significant (p < 0.05). Micro-CT investigation revealed that the enamel volume decreased after demineralization and increased after remineralization among all groups. The F-BG toothpaste showed greater enamel surface micro-hardness (increased VHN), smoother surface (low roughness), and better volume restoration (remineralization) in comparison to the fluoride toothpaste.

Evaluation of bioactive glass scaffolds incorporating SrO or ZnO for bone repair: In vitro bioactivity and antibacterial activity

A series of bioactive glass scaffolds doped with SrO or ZnO (0, 5, and 10 mol%) were synthesized by the foam replica and melting method. The thermodynamic evolution, phase composition, microstructure, ion release, in vitro bioactivity, and oxygen density of the scaffolds were characterized. The proliferation of murine long bone osteocyte Y4 cells was studied by cell culture. The survival rate of the BGs evaluated the antibacterial activity and Escherichia coli strains in co-culture. The results indicated that the process window decreases with the increase of dopants. All the samples have a pore structure size of 200-400 μm. When the scaffolds were immersed in simulated body fluid for 28 days, hydroxyapatite formation was not affected, but the degradation process was retarded. The glass network packing and ionic radii variations of the substitution ions control surface degradation, glass dissolution, and ion release. MTT results revealed that 5Sr-BG had a significant effect on promoting cell proliferation and none of the BGs were cytotoxicity. Sr-BGs and Zn-BGs exhibited significantly inhibited growth against E. coli bacterial strains. Generally, these results showed the 5Sr-BG scaffold with high vitro bioactivity, cell proliferation, and antibacterial property is an important candidate material for bone tissue regeneration and repair.

Improvement of the mechanical and biological properties of bioactive glasses by the addition of zirconium oxide (ZrO2 ) as a synthetic bone graft substitute

In this study, mechanical properties of bioactive glass (BAG) synthetic bone graft substitute was improved by containing ZrO2 (ZrO2 -BAG), while maintaining advantageous biological properties of BAG such as osteoinductive and osteoconductive properties. The ZrO2 -BAG was produced by adding ZrO2 in the following proportions to replace Na2 O in 45S5 BAG: 1% (Zr1-BAG), 3% (Zr3-BAG), 6% (Zr6-BAG), and 12% (Zr12-BAG). Properties including XRD, XPS, SEM, DSC, fracture toughness, and Vickers microhardness were evaluated. To assess the biological properties, Ca/P apatite formation, ion release, degradation rate, cell proliferation, ALP activity (ALP), and alizarin red S staining assay (ARS) were evaluated. Also, expression of osteogenic differentiation markers, Osteopontin (OPN), confirmed by immunofluorescence staining. Finally, an in vivo test was carried out to by implanting ZrO2 -BAG into the subcutaneous tissue of rats. The results of each test were statistically analyzed with one-way ANOVA followed by Tukey's post hoc statistical test. Amorphous ZrO2 -BAG was successfully produced with increased mechanical properties as the ZrO2 content was increased. Additionally, ZrO2 -BAG exhibited a slower ion release and degradation rate compare to BAG without ZrO2 . Bioactivity of ZrO2 -BAG was confirmed with apatite layer formed on the surface, significantly higher proliferation rate and significantly enhanced ALP and the degree of ARS of the cells compare to respective controls. The tissue reactions observed in the in vivo study showed neo-formed vessels after implantation of ZrO2 -BAG.

The Influence of Strontium on Bone Tissue Metabolism and Its Application in Osteoporosis Treatment

Osteoporosis is a chronic disease characterized by low bone mass caused by increased bone turnover and impaired bone microarchitecture. In treatment, we use antiresorptive or anabolic drugs, which usually have a unidirectional effect, i.e., they inhibit the activity of osteoclasts or stimulate the effect of osteoblasts. Strontium ranelate is an anti-osteoporosis drug with a unique mechanism of action (used primarily in postmenopausal women). Unlike other medicines, it has a multidirectional effect on bone tissue, intensifying osteoblastogenesis while inhibiting osteoclastogenesis. It turns out that this effect is demonstrated by strontium ions, an element showing physical and chemical similarity to calcium, the basic element that builds the mineral fraction of bone. As a result, strontium acts through the calcium-sensing receptor (CaSR) receptor in bone tissue cells. In recent years, there has been a significant increase in interest in the introduction of strontium ions in place of calcium ions in ceramics used as bone replacement materials for the treatment of bone fractures and defects caused by osteoporosis. The aim of this study was to summarize current knowledge about the role of strontium in the treatment of osteoporosis, its effects (in various forms), and the ways in which it is administered.

Bioactive glasses and electrospun composites that release cobalt to stimulate the HIF pathway for wound healing applications

BACKGROUND

Bioactive glasses are traditionally associated with bonding to bone through a hydroxycarbonate apatite (HCA) surface layer but the release of active ions is more important for bone regeneration. They are now being used to deliver ions for soft tissue applications, particularly wound healing. Cobalt is known to simulate hypoxia and provoke angiogenesis. The aim here was to develop new bioactive glass compositions designed to be scaffold materials to locally deliver pro-angiogenic cobalt ions, at a controlled rate, without forming an HCA layer, for wound healing applications.

METHODS

New melt-derived bioactive glass compositions were designed that had the same network connectivity (mean number of bridging covalent bonds between silica tetrahedra), and therefore similar biodegradation rate, as the original 45S5 Bioglass. The amount of magnesium and cobalt in the glass was varied, with the aim of reducing or removing calcium and phosphate from the compositions. Electrospun poly(ε-caprolactone)/bioactive glass composites were also produced. Glasses were tested for ion release in dissolution studies and their influence on Hypoxia-Inducible Factor 1-alpha (HIF-1α) and expression of Vascular Endothelial Growth Factor (VEGF) from fibroblast cells was investigated.

RESULTS

Dissolution tests showed the silica rich layer differed depending on the amount of MgO in the glass, which influenced the delivery of cobalt. The electrospun composites delivered a more sustained ion release relative to glass particles alone. Exposing fibroblasts to conditioned media from these composites did not cause a detrimental effect on metabolic activity but glasses containing cobalt did stabilise HIF-1α and provoked a significantly higher expression of VEGF (not seen in Co-free controls).

CONCLUSIONS

The composite fibres containing new bioactive glass compositions delivered cobalt ions at a sustained rate, which could be mediated by the magnesium content of the glass. The dissolution products stabilised HIF-1α and provoked a significantly higher expression of VEGF, suggesting the composites activated the HIF pathway to stimulate angiogenesis.

The use of bioactive glass (BAG) in dental composites: A critical review

OBJECTIVE

In recent years, numerous studies have analyzed the role of bioactive glass (BAG) as remineralizing additives in dental restorative composites. This current review provides a critical analysis of the existing literature, particularly focusing on BAGs prepared via the melt-quench route that form an "apatite-like" phase when immersed in physiological-like solutions.

METHODS

Online databases (Science Direct, PubMed and Google Scholar) were used to collect data published from 1962 to 2020. The research papers were analyzed and the relevant papers were selected for this review. Sol-gel BAGs were not included in this review since it is not a cost-effective manufacturing technique that can be upscaled and is difficult to incorporate fluoride.

RESULTS

BAGs release Ca²⁺, PO₄^3- and F^- ions, raise the pH and form apatite. There are numerous published papers on the bioactivity of BAGs, but the different glass compositions, volume fractions, particle sizes, immersion media, time points, and the characterization techniques used, make comparison difficult. Several papers only use certain characterization techniques that do not provide a full picture of the behavior of the glass. It was noted that in most studies, mechanical properties were measured on dry samples, which does not replicate the conditions in the oral environment. Therefore, it is recommended that samples should be immersed for longer time periods in physiological solutions to mimic clinical environments.

SIGNIFICANCE

BAGs present major benefits in dentistry, especially their capacity to form apatite, which could potentially fill any marginal gaps produced due to polymerization shrinkage.

The effects of strontium-doped bioactive glass and fluoride on hydroxyapatite crystallization

OBJECTIVES

This study investigated the effects of a new strontium-doped bioactive glass and fluoride on hydroxyapatite crystallization.

METHODS

We designed an in vitro experiment with calcium phosphate (CaCl₂·2H₂O + K₂HPO₄ in buffer solution) with different concentrations of strontium-doped bioactive glass (1 mg/mL or 5 mg/mL), and different concentrations of fluoride (0 ppm, 1 ppm or 5 ppm). Tris-buffered saline served as negative control. After incubation at 37 ℃ for 48 h, the shape and organization of crystals were examined by transmission electron microscopy (TEM) and electron diffraction. Structure of the crystals was assessed by powder X-ray diffraction (P-XRD) and unit cell parameters were calculated. Characterization of the crystals were performed by Raman spectroscopy and Fourier Transform Infrared Spectroscopy (FTIR).

RESULTS

TEM and selected-area electron diffraction revealed that the precipitates in all experimental groups were crystalline apatite. There was an interaction between strontium and fluoride with different concentrations on crystal thickness (p = 0.008). P-XRD indicated the formation of strontium-substituted-fluorohydroxyapatite and strontium-substituted-hydroxyapatite in the groups with both bioactive glass and fluoride. Expansion or contraction of crystal unit cell was influenced by the concentrations of strontium and fluoride. Raman spectra showed strong phosphate band at 960 cm^-1 in all experimental groups and displayed no obvious shift. FTIR results confirmed the formation of apatite.

CONCLUSIONS

The results of this study suggest that strontium-doped bioactive glass and fluoride have synergistic effects on hydroxyapatite crystallization.

CLINICAL SIGNIFICANCE

Strontium-doped bioactive glass and fluoride have synergistic effects on hydroxyapatite crystallization by producing strontium-substituted-hydroxyapatite and strontium-substituted-fluorohydroxyapatite with enhanced bioactivity and reduced solubility which could be beneficial for caries management.

Effects of bioactive glass coating by electrophoretic deposition on esthetical, bending, and frictional performance of orthodontic stainless steel wire

We investigated the surface modification of orthodontic stainless steel wire using electrophoretic deposition (EPD) of bioactive glass (BG). BG coatings were characterized by spectrophotometry, three-dimensional (3D) focal laser scanning microscopy and scanning electron microscopy. The mechanical properties of the BG-coated wires were estimated nanoindentation, three-point bending and drawing friction tests. BG-coated specimens prepared at higher voltage showed higher values for both reflectance and L^* compared to those prepared at lower voltage. Specimens coated at higher voltage had significantly lower surface roughness than those coated at lower voltage, and their BG layers had higher hardness and elastic modulus values. In the three-point bending test, BG-coated wires produced significantly lower elastic modulus than non-coated wires. Most BG-coated specimens produced similar frictional forces to those produced by non-coated specimens. The surface modification technique applying EPD and BG coating to orthodontic stainless steel wire could be used to develop new esthetical orthodontic wire.

A review of the latest insights into the mechanism of action of strontium in bone

Interest in strontium (Sr) has persisted over the last three decades due to its unique mechanism of action: it simultaneously promotes osteoblast function and inhibits osteoclast function. While this mechanism of action is strongly supported by in vitro studies and small animal trials, recent large-scale clinical trials have demonstrated that orally administered strontium ranelate (SrRan) may have no anabolic effect on bone formation in humans. Yet, there is a strong correlation between Sr accumulation in bone and reduced fracture risk in post-menopausal women, suggesting Sr acts via a purely physiochemical mechanism to enhance bone strength. Conversely, the local administration of Sr with the use of modified biomaterials has been shown to enhance bone growth, osseointegration and bone healing at the bone-implant interface, to a greater degree than Sr-free materials. This review summarizes current knowledge of the main cellular and physiochemical mechanisms that underly Sr's effect in bone, which center around Sr's similarity to calcium (Ca). We will also summarize the main controversies in Sr research which cast doubt on the 'dual-acting mechanism'. Lastly, we will explore the effects of Sr-modified bone-implant materials both in vitro and in vivo, examining whether Sr may act via an alternate mechanism when administered locally.

Microwave irradiation assisted sodium hexametaphosphate modification on the alkali-activated blast furnace slag for enhancing immobilization of strontium

An inadvertent leakage of ⁹⁰Sr into the environment can induce an easy accumulation in biosphere and cause a continuous radiation to the surrounding ecosystem. In this study, sodium hexametaphosphate (Na₆O₁₈P₆) was employed to modify the blast furnace slags (BFS) to enhance the chemical stabilization of Sr²⁺ ions in the BFS-based cementitious materials. Microwave irradiation (MW) was used to further increase the binder activity of BFS samples and strengthened the mechanical strengths and durability of BFS-based blocks. A combination of experimental factors including the mass ratio of Na₆O₁₈P₆ to BFS-Sr_0.1 of 15%, the ratio of solid to liquid of 1:4 mg/L, the output power of 650 W, and the activation time of 3 min was most conductive to achieving an optimal microwave-irradiation process. Four extraction solutions were sorted by their leaching abilities following as MgSO₄ solution > H₂SO₄ solution > CH₃OOH solution > deionized (DI) water based on their leaching results. Compared with microwave irradiation, an addition of Na₆O₁₈P₆ to BFS samples obtained a better compressive strength for BFS-based blocks. However, a microwave-irradiation treatment was more effective in improving the resistances of blocks to gamma irradiation and thermal-thaw changes. Exposing to gamma irradiation over 6 months and enduring to thermal-thaw tests over 15 cycles, the microwave-treated blocks only lost 3.29% and 2.23% of leaching removal efficiencies in deionized water, respectively. Microwave irradiation increased the mechanical strengths of BFS-based blocks and inhibited leaching of Sr²⁺ ions from matrices mainly by strengthening hydration reactions and Sr²⁺ encapsulation.

Strontium- and Zinc-Containing Bioactive Glass and Alginates Scaffolds

With an increasingly elderly population, there is a proportionate increase in bone injuries requiring hospitalization. Clinicians are increasingly adopting tissue-engineering methods for treatment due to limitations in the use of autogenous and autologous grafts. The aim of this study was to synthesize a novel, bioactive, porous, mechanically stable bone graft substitute/scaffold. Strontium- and zinc-containing bioactive glasses were synthesized and used with varying amounts of alginate to form scaffolds. Differential scanning calorimetric analysis (DSC), FTIR, XRD, and NMR techniques were used for the characterization of scaffolds. SEM confirmed the adequate porous structure of the scaffolds required for osteoconductivity. The incorporation of the bioactive glass with alginate has improved the compressive strength of the scaffolds. The bioactivity of the scaffolds was demonstrated by an increase in the pH of the medium after the immersion of the scaffolds in a Tris/HCl buffer and by the formation of orthophosphate precipitate on scaffolds. The scaffolds were able to release calcium, strontium and zinc ions in the Tris/HCl buffer, which would have a positive impact on osteogenesis if tested in vivo.

Strontium ion reinforced bioceramic scaffold for load bearing bone regeneration

Bone defects in load bearing areas require bone reconstruction with strong biomaterial having mechanical characteristics like cortical bone. Bioceramics are biomaterials that support bone formation as well as provide adequate mechanical properties. A strontium substitution of the bioceramic is expected to further increase its bioactivity by enhancing osteogenesis and protect the bone from osteoclastic resorption. The study involves development, characterization and in vivo testing of a newly developed strontium substituted hydroxyapatite based bioceramic scaffold (SrHAB) with sufficient biomechanical properties. Optimal concentration of strontium ion required for enhanced osteogenic differentiation was identified by comparing three compositions of SrHAB scaffold; namely Sr10HAB, Sr30HAB and Sr50 HAB for their Alkaline phosphatase activity in vitro. The selected Sr10HAB scaffold demonstrated in vivo bone formation with osteogenic differentiation of stromal derived mesenchymal stem cells (MSC) from human and ovine sources in ectopic and ovine models. Thus, Sr10HAB scaffold has a potential for application in load bearing bone requirements of orthopaedics and dentistry.

Characterization of the bioactivity of two commercial composites

The aim of this study was to characterize the ion release, pH changes and apatite formation ability of two potentially bioactive composites Cention N (CN) and Activa (ACT). Ion release and apatite formation was investigated in three different immersion media: Tris buffer pH 7.3 (TB), Artificial Saliva pH 4 (AS4) and Artificial Saliva pH 7 (AS7) in order to mimic the conditions present in the mouth. Fluoride release was followed using an ion selective electrode, whilst all other ions were determined by inductively coupled plasma optical emission spectroscopy. Apatite formation was followed by FTIR and XRD. SEM was used to follow glass degradation and apatite formation on both polished cross-sections and surfaces of the composites. ACT released very few ions including fluoride upon immersion in TB and AS7, but released more ions including significant quantities of Al in AS4. This would suggest the glasses in ACT are acid degradable fluoro-alumino-silicate glasses similar to the glasses used in glass ionomer cements. There was no evidence of any apatite formation with ACT. CN released more ions in TB and AS7 than ACT and formed an apatite like phase in AS7. The calcium fluoro-silicate glass in CN was observed to degrade significantly in AS4. CN has bioactive properties that may explain the low incidence of secondary caries found clinically with this composite.

Multiple and Promising Applications of Strontium (Sr)-Containing Bioactive Glasses in Bone Tissue Engineering

Improving and accelerating bone repair still are partially unmet needs in bone regenerative therapies. In this regard, strontium (Sr)-containing bioactive glasses (BGs) are highly-promising materials to tackle this challenge. The positive impacts of Sr on the osteogenesis makes it routinely used in the form of strontium ranelate (SR) in the clinical setting, especially for patients suffering from osteoporosis. Therefore, a large number of silicate-, borate-, and phosphate-based BGs doped with Sr and produced in different shapes have been developed and characterized, in order to be used in the most advanced therapeutic strategies designed for the management of bone defects and injuries. Although the influence of Sr incorporation in the glass is debated regarding the obtained physicochemical and mechanical properties, the biological improvements have been found to be substantial both in vitro and in vivo. In the present study, we provide a comprehensive overview of Sr-containing glasses along with the current state of their clinical use. For this purpose, different types of Sr-doped BG systems are described, including composites, coatings and porous scaffolds, and their applications are discussed in the light of existing experimental data along with the significant challenges ahead.

Development and Characterization of Composites Consisting of Calcium Phosphate Cements and Mesoporous Bioactive Glass for Extrusion-Based Fabrication

Calcium phosphate cements (CPC) and mesoporous bioactive glasses (MBG) are two degradable biomaterial groups widely under investigation concerning their applicability to treat bone defects. MBG-CPC composites were recently shown to possess enhanced degradation properties in comparison to pure CPC. In addition, modification of MBG allows an easy incorporation of therapeutically effective ions. Additive manufacturing of such composites enables the fabrication of patient-specific geometries with further improved degradation behavior due to control over macroporosity. In this study, we developed composites prepared from a non-aqueous carrier-liquid (cl) based CPC paste and MBG particles suitable for extrusion-based additive manufacturing (3D plotting). CPC with the addition of up to 10 wt % MBG were processible by adjusting the amount of cl. Scaffolds consisting of a 4, 6 and 8%-MBG-CPC composite were successfully manufactured by 3D plotting. While mechanically characterization of the scaffolds showed an influence of the MBG, no changes of microstructure were observed. During degradation of the composite, the release of Ca2+ and Sr2+ ions could be controlled by the MBG composition and plotted scaffolds with macropores showed a significant higher release than bulk samples of comparable mass. These findings demonstrate a high flexibility regarding ion release of the developed composites and suggest utilizing the drug binding capacities of MBG as a prospective delivery system for biologically active proteins.

Randomized investigation of the bioavailability of fluoride in saliva after administration of sodium fluoride, amine fluoride and fluoride containing bioactive glass dentifrices

OBJECTIVES

Bioactive glasses which degrade in aqueous solutions may release bioactive ions such as fluoride (F-) and support fluoride bioavailability in saliva. We investigated how these effects would be apparent in an in vivo experimental trial after toothbrushing in comparison with sodium fluoride and amine fluoride.

MATERIAL AND METHODS

In this single-center, randomized, parallel in vivo trial with a three strata block design, where healthy subjects were randomly assigned into three groups. Each group brushed their teeth either with fluoridated bioactive glass containing dentifrice, with a sodium fluoride (NaF) containing dentifrice or with amine fluoride (AmF) containing toothpaste. Saliva was collected time intervals before, immediately after, 30, 60 and 120 min after toothbrushing. Fluoride concentration was determined in supernatant saliva and salivary sediment using a fluoride ion selective electrode. The data were evaluated statistically using non-parametric tests.

RESULTS

The increase of bioactive fluoride in supernatant saliva was higher after application of NaF or AmF compared to fluoridated bioactive glass. In salivary sediment bioavailability of fluoride lasted longer after application of fluoridated bioactive glass.

CONCLUSIONS

Toothbrushing with the fluoride containing bioactive glass dentifrices had positive effects on the fluoride bioavailability within two hours. Fluoride containing bioactive glass represent a new area for investigation in caries prophylaxis. The bioactive potential impact on the tooth remineralization should be examined further.

TRIAL REGISTRATION

DRKS00016038 .