Changes induced by ozone and ultraviolet light in type I collagen. Bovine Achilles tendon collagen versus rat tail tendon collagen

Effects of processing and gamma radiation on mechanical properties and organic composition of frozen, freeze-dried and demineralised human cortical bone allograft

Bone processing and radiation were reported to influence mechanical properties of cortical bones due in part to structural changes and denaturation of collagen composition. This comparative study was to determine effects of bone processing on mechanical properties and organic composition, and to what extent the radiation damaging after each processing. Human femur cortical bones were processed by freezing, freeze-drying and demineralisation and then gamma irradiated at 5, 15, 20, 25 and 50 kGy. In the compression test, freeze drying significantly decreased the Young's Modulus by 15%, while demineralisation reduced further by 90% (P < 0.05) when compared to the freezing. Only demineralisation significantly reduced ultimate strength of bone by 93% (P < 0.05). In the bending test, both freeze drying and demineralisation significantly reduced the ultimate strength and the work to failure. Radiation at 25 kGy showed no effect on compression for ultimate strength in each processing group. However, high dose of 50 kGy significantly reduced bending ultimate strength by 47% in demineralisation group. Alterations in collagen in bones irradiated at 25 and 50 kGy showed by the highest peak of the amide I collagen in the Fourier Transfer Infra-Red spectra indicating more collagen was exposed after calcium was removed in the demineralised bone, however radiation showed no effect on the collagen crosslink. The study confirmed that demineralisation further reduced the ability to resist deformation in response to an applied force in freeze-dried bones due to calcium reduction and collagen composition. Sterilisation dose of 25 kGy has no effect on mechanical properties and collagen composition of the processed human cortical bone.

The Influence of UV Light on Rheological Properties of Collagen Extracted from Silver Carp Skin

Acid soluble collagen (ASC) was extracted from Silver Carp fish skin. Collagen was dissolved in acetic acid at varying concentrations and its rheological properties were studied. Steady shear flow properties of collagen solutions at concentrations of 5 and 10 mg/mL were characterized using rheometry at 20 °C. Collagen solutions were irradiated with UV light (wavelength 254 nm) for up to 2 h and rheological properties were measured. All the collagen solutions showed a shear-thinning flow behavior. A constant viscosity region was observed after 1 h of UV irradiation, which showed that collagen molecules were fully denatured. A short treatment with collagen solution by UV (ultraviolet) light led to an increase in viscosity; however, the denaturation temperature of UV-irradiated collagen decreased. Depending on the time of UV treatment, collagen extracted from Silver Carp fish skin may undergo physical crosslinking or photodegradation. Physically crosslinked collagen may find applications in functional food, cosmetic, biomedical, and pharmaceutical industries.

Mapping metabolism of liver tissue using two-photon FLIM

Although fluorescence lifetime imaging microscopy (FLIM) has been extensively applied to study cellular metabolism in the liver, there is neither an established approach to analyze the data, nor have appropriate protocols been developed to maintain the optical metabolic characteristics in the ex vivo liver tissue sample. Here, we show that a tri-exponential decay fitting model for the fluorescence signal from nicotinamide adenine dinucleotide (NAD(P)H) and the use of ex vivo samples allows the most appropriate processing of the FLIM data. Moreover, we determine the medium that maintains the initial metabolic state of hepatocytes (liver cells), most effectively. Our results should be particularly relevant for the interrogation of liver samples, not only in laboratory research, but also in clinical settings in the future.

Ultraviolet light (365 nm) transmission properties of articular cartilage as a function of depth, extracellular matrix, and swelling

Current tissue engineering approaches for treatment of injured or diseased articular cartilage use ultraviolet light (UV) for in situ photopolymerization of biomaterials to fill chondral and osteochondral defects as well as resurfacing, stiffening and bonding the extracellular matrix and tissue interfaces. The most commonly used UV light wavelength is UVA 365 nm, the least cytotoxic and deepest penetrating. However, little information is available on the transmission of UVA 365 nm light through the cartilage matrix. In the present study, 365 nm UV light transmission was measured as a function of depth through 100 μm thick slices of healthy articular cartilage removed from mature bovine knees. Transmission properties were measured in normal (Native) cartilage and after swelling equilibration in phosphate-buffered saline (Swollen). Single-factor and multiple linear regression analyses were performed to determine depth-dependencies between the effective attenuation coefficients and proteoglycan, collagen and water contents. For both cartilages, a significant depth-dependency was found for the effective attenuation coefficients, being highest at the articular surface (superficial zone) and decreasing with depth. The effective attenuation coefficients for full-thickness cartilages were approximately a third lower than the total attenuation coefficients calculated from the individual slices. Analysis of absorption and scattering effects due to the ECM and chondrocytes found that UV light scatter coefficients were ∼10 times greater than absorption coefficients. The greater transmittance of UV light through the thicker cartilage was attributed to the collagen within the ECM causing significant backscatter forward reflectance.

Fabrication and preliminary in vitro evaluation of ultraviolet-crosslinked electrospun fish scale gelatin nanofibrous scaffolds

This study aimed to explore a potential use of fish scale-derived gelatin nanofibrous scaffolds (GNS) in tissue engineering due to their biological and economical merits. Extraction of gelatin was achieved via decalcification, sonication and lyophilization of mixed fish scales. To fabricate nano-scale architecture of scaffolds analogous to natural extracellular matrix, gelatin was rendered into nanofibrous matrices through 6-h electrospinning, resulting in the average diameter of 48 ± 12 nm. In order to improve the water-resistant ability while retaining their biocompatibility, GNS were physically crosslinked with ultraviolet (UV) irradiation for 5 min (UGN5), 10 min (UGN10) and 20 min (UGN20). On average, the diameter of nanofibers increased by 3 folds after crosslinking, however, Fourier transform infrared spectroscopy analysis confirmed that no major alterations occurred in the functional groups of gelatin. A degradation assay showed that UGN5 and UGN10 scaffolds remained in minimum essential medium for 14 days, while UGN20 scaffolds degraded completely after 10 days. All UGN scaffolds promoted adhesion and proliferation of human keratinocytes, HaCaT, without causing an apparent cytotoxicity. UGN5 scaffolds were shown to stimulate a better growth of HaCaT cells compared to other scaffolds upon 1 day of incubation, whereas UGN20 had a long-term effect on cells exhibiting 25% higher cell proliferation than positive control after 7 days. In the wound scratch assay, UGN5 scaffolds induced a rapid cell migration closing up to 79% of an artificial wound within 24 h. The current findings provide a new insight of UGN scaffolds to serve as wound dressings in the future. In the wound scratch assay, UGN5 induced a rapid cell migration closing up to 79% of an artificial wound within 24 h.

Stain-free LED scanning lifetime imaging system for diabetes modified tissue matrices

In contrast to labor intensive and destructive histological techniques, intrinsic autofluorescence lifetimes of extra cellular matrix proteins can provide label-free imaging of tissue modifications in diseases, including the diabetic ulcers. However, decoupling the complex mixture of tissue fluorophores requires costly and complicated fluorescent lifetime instrumentation. Furthermore, a list of autofluorescent and fluorogenic proteins must be characterized to profile their changes during disease progression. Towards these goals, an imaging system based on frequency domain light-emitting diode (LED) modulation was designed and demonstrated, using off-the-shelf components in a low complexity design. The system was operated by coupling and imaging fluorescence intensities using a pair of objectives. The system's scanning and signal acquisition performances were optimized with respect to etendues. To study fluorescent proteins in diabetic ulcers, lifetimes from purified and pentosidine modified collagen I, collagen III, and elastin were measured. Pentosidine measurements showed a decrease in autofluorescent lifetimes while elevated collagen III in diabetic ulcers showed increased lifetimes. These lifetimes, plus future protein measurements enabled by our system, can serve as standards for developing a biophotonic model of diabetic ulcers. As a proof-of-concept, a 3 cm × 3 cm diabetic foot ulcer was imaged using the developed system. Phasor analysis was applied to aid the interpretation of lifetime images. As a result, a compact biophotonic imaging system targeting diabetic tissue was achieved, towards making the technique accessible for clinical histology.

Effect of x-rays and gamma radiations on the bone mechanical properties: literature review

The bone auto grafting, isografting, allografting and xenografting are used for defective bone replacement or treatment in almost all living species. The X-ray and Gamma (electromagnetic radiation) sterilization performed on the donor bone graft to prevent toxicity or migration of virus/bacterial infections from donors to reciver. Conversely, X-ray and Gamma radiation deteriorates the bone mechanical properties and bone become more susceptible to fracture. Fracture toughness as well as other mechanical properties of bone change with these radiations. In this literature review the effect of the X-rays and Gamma radiation on bone mechanical properties are discussed. All relevant literature was reviewed. After reviewing the literature only the research relating to the effect of X-rays and Gamma radiations on bone mechanical properties are included. Literature studies showed significant effect of the X-rays and Gamma radiations on the mechanical properties of the bones. In some studies the differences exists on the doses of radiations which were discussed in this study. The high energetic electromagnetic radiation (X-rays and Gamma radiations) changed/modify the collagen network of the bone, which reduced the mechanical properties of bone; however these changes depend on the radiation dose.

Detection of Pentosidine Cross-Links in Cell-Secreted Decellularized Matrices Using Time Resolved Fluorescence Spectroscopy

Hyperglycemia-mediated, nonenzymatic collagen cross-links such as pentosidine (PENT) can have deleterious effects on cellular interactions with the extracellular matrix (ECM). Present techniques to quantify PENT are limited, motivating the need for improved methods to study the accumulation and contribution of PENT toward diabetic clinical challenges such as impaired bone healing. Current methods for studying PENT are destructive, laborious, and frequently employ oversimplified collagen films that lack the complexity of the native ECM. The primary goal of this study was to evaluate the capacity of time-resolved fluorescence spectroscopy (TRFS) to detect PENT in cell-secreted ECMs possessing enhanced compositional complexity. To demonstrate an application of this method, we assessed the response of human mesenchymal stem cells (MSCs) to cross-linked substrates to explore the role of detected PENT on osteogenic differentiation. We exposed MSC-secreted decellularized matrices (DMs) to 0.66 M ribose for 2 weeks and used TRFS to detect the accumulation of PENT. Ribose treatment resulted in a 30 nm blue shift in peak fluorescence emission and a significant decrease in average lifetime compared to that of control DMs (4.4 ± 0.3 ns vs 3.5 ± 0.09 ns). Evaluation of samples with high performance liquid chromatography (HPLC) confirmed that changes in observed fluorescence were due to PENT accumulation. A strong correlation was found between TRFS parameters and the HPLC measurement of PENT, validating the use of TRFS as an alternative method of PENT detection. Osteoblastic gene expression was significantly reduced in MSCs seeded on ribose DMs at days 7 and 14. However, no significant differences in calcium deposition were detected between control and ribose DMs. These data demonstrate the efficacy of nondestructive fluorescence spectroscopy to examine the formation of nonenzymatic collagen cross-links within biomimetic culture platforms and showcase one example where an improved biomimetic substrate can be used to probe cell-ECM interactions in the presence of collagen cross-links.

Atmospheric chemistry of bioaerosols: heterogeneous and multiphase reactions with atmospheric oxidants and other trace gases

Once airborne, biologically-derived aerosol particles are prone to reaction with various atmospheric oxidants such as OH, NO₃, and O₃.

Advances in analytical techniques and instrumentation have now established methods for detecting, quantifying, and identifying the chemical and microbial constituents of particulate matter in the atmosphere. For example, recent cryo-TEM studies of sea spray have identified whole bacteria and viruses ejected from ocean seawater into air. A focal point of this perspective is directed towards the reactivity of aerosol particles of biological origin with oxidants (OH, NO₃, and O₃) present in the atmosphere. Complementary information on the reactivity of aerosol particles is obtained from field investigations and laboratory studies. Laboratory studies of different types of biologically-derived particles offer important information related to their impacts on the local and global environment. These studies can also unravel a range of different chemistries and reactivity afforded by the complexity and diversity of the chemical make-up of these particles. Laboratory experiments as the ones reviewed herein can elucidate the chemistry of biological aerosols.

Damage to skin extracellular matrix induced by UV exposure

SIGNIFICANCE

Chronic exposure to environmental ultraviolet radiation (UVR) plays a key role in both photocarcinogenesis and induction of accelerated skin aging. Although the spatiotemporal consequences of UVR exposure for the composition and architecture of the dermal extracellular matrix (ECM) are well characterized, the pathogenesis of photoaging remains poorly defined. Given the compelling evidence for the role of reactive oxygen species (ROS) as mediators of photoaging, UVR-exposed human skin may be an accessible model system in which to characterize the role of oxidative damage in both internal and external tissues.

RECENT ADVANCES

Although the cell-mediated degradation of dermal components via UVR-induced expression of ECM proteases has long been identified as an integral part of the photoaging pathway, the relative importance and identity of cellular and extracellular photosensitizers (direct hit and bystanders models, respectively) in initiating this enzymatic activity is unclear. Recently, both age-related protein glycation and relative amino-acid composition have been identified as potential risk factors for photo-ionization and/or photo-sensitization. Here, we propose a selective multi-hit model of photoaging.

CRITICAL ISSUES

Bioinformatic analyses can be employed to identify candidate UVR targets/photosensitizers, but the action of UVR on protein structure and/or ROS production should be verified experimentally. Crucially, in the case of biochemically active ECM components such as fibronectin and fibrillin, the downstream effects of photo-degradation on tissue homeostasis remain to be confirmed.

FUTURE DIRECTIONS

Both topical antioxidants and inhibitors of detrimental cell signaling may be effective in abrogating the effects of specific UVR-mediated protein degradation in the dermis.

Photobleaching as a tool to measure the local strain field in fibrous membranes of connective tissues

Connective tissues are complex structures which contain collagen and elastin fibers. These fiber-based structures have a great influence on material mechanical properties and need to be studied at the microscopic scale. Several microscopy techniques have been developed in order to image such microstructures; among them are two-photon excited fluorescence microscopy and second harmonic generation. These observations have been coupled with mechanical characterization to link microstructural kinematics to macroscopic material parameter evolution. In this study, we present a new approach to measure local strain in soft biological tissues using a side-effect of fluorescence microscopy: photobleaching. Controlling the loss of fluorescence induced by photobleaching, we create a pattern on our sample that we can monitor during mechanical loading. The image analysis allows three-dimensional displacements of the patterns at various loading levels to be computed. Then, local strain distribution is derived using the finite element discretization on a four-node element mesh created from our photobleached pattern. Photobleaching tests on a human liver capsule have revealed that this technique is non-destructive and does not have any impact on mechanical properties. This method is likely to have other applications in biological material studies, considering that all collagen-elastin fiber-based biological tissues possess autofluorescence properties and thus can be photobleached.

Efficient expansion of mouse primary tenocytes using a novel collagen gel culture method

Development of regenerative therapies for damaged tendons remains a great challenge, largely because of lack of information regarding the mechanisms responsible for differentiation of tenocytes. Mouse tenocytes have not been fully characterized owing to the absence of efficient and reproducible methods for their in vitro expansion without losing phenotypic features. The objective of the study was to establish an improved and reliable method for stable primary culture of mouse tenocytes by using collagen gel. Achilles and tail tendon tissues were harvested and embedded in collagen gel. After 10 days of continuous culture, the gel was digested and cells were passaged on tissue culture-treated plastic dishes. Mouse tenocytes cultured in collagen gel exhibited significantly shorter doubling time and higher numbers of proliferation when maintained on the plastic dishes compared with those cultured without using gel. Transmission electron microscopic analyses showed that cultured tenocytes retained some morphological features of tenocytes in tendon tissues, such as cell-cell junctional complex formation, well-developed rough endoplasmic reticulum, and mitochondria in their cytoplasm. mRNA expression of tenocyte markers (tenomodulin, type I collagen, periostin, and scleraxis) was higher in cells cultured in collagen gel than in those cultured in the absence of gel. Our results show that tenocytes cultured using the collagen gel method express typical lineage markers and exhibit improved growth characteristics, thus providing a stable platform for studying molecular mechanisms that control their differentiation.

Changes in fluorescence spectra of bioaerosols exposed to ozone in a laboratory reaction chamber to simulate atmospheric aging

A laboratory system for exposing aerosol particles to ozone and rapidly measuring the subsequent changes in their single-particle fluorescence is reported. The system consists of a rotating drum chamber and a single-particle fluorescence spectrometer (SPFS) utilizing excitation at 263 nm. Measurements made with this system show preliminary results on the ultra-violet laser-induced-fluorescence (UV-LIF) spectra of single aerosolized particles of Yersinia rohdei, and of MS2 (bacteriophage) exposed to ozone. When bioparticles are exposed in the chamber the fluorescence emission peak around 330 nm: i) decreases in intensity relative to that of the 400-550 nm band; and ii) shifts slightly toward shorter-wavelengths (consistent with further drying of the particles). In these experiments, changes were observed at exposures below the US Environmental Protection Agency (EPA) limits for ozone.

UV damage of collagen: insights from model collagen peptides

Fibrils of Type I collagen in the skin are exposed to ultraviolet (UV) light and there have been claims that collagen photo-degradation leads to wrinkles and may contribute to skin cancers. To understand the effects of UV radiation on collagen, Type I collagen solutions were exposed to the UV-C wavelength of 254 nm for defined lengths of time at 4°C. Circular dichroism (CD) experiments show that irradiation of collagen leads to high loss of triple helical content with a new lower thermal stability peak and SDS-gel electrophoresis indicates breakdown of collagen chains. To better define the effects of UV radiation on the collagen triple-helix, the studies were extended to peptides which model the collagen sequence and conformation. CD studies showed irradiation for days led to lower magnitudes of the triple-helix maximum at 225 nm and lower thermal stabilities for two peptides containing multiple Gly-Pro-Hyp triplets. In contrast, the highest radiation exposure led to little change in the T(m) values of (Gly-Pro-Pro)(10) and (Ala-Hyp-Gly)(10) , although (Gly-Pro-Pro)(10) did show a significant decrease in triple helix intensity. Mass spectroscopy indicated preferential cleavage sites within the peptides, and identification of some of the most susceptible sites of cleavage. The effect of radiation on these well defined peptides gives insight into the sequence and conformational specificity of photo-degradation of collagen.

Effects of zero-length and non-zero-length cross-linking reagents on the optical spectral properties and structures of collagen hydrogels

We compared the effects of zero-length cross-linkers 1-ethyl-3 (3dimethylaminopropyl) carbodiimide (EDC) and non-zero-length cross-linkers glycolaldehyde and glyceraldehyde on the optical and structural properties of three-dimensional (3D) collagen hydrogels. We evaluated these effects by multiphoton microscopy (MPM) that combined two-photon fluorescence (TPF) and second harmonic generation (SHG) contrasts and transmission electron microscopy (TEM). The collagen hydrogels were incubated separately with the above-mentioned reagents present at the concentration of 0.1 M. The incubation with glycolaldehyde and glyceraldehyde induced strong autofluorescence within the gels. We followed the formation of fluorescence with TPF signals in situ and in real time as well as characterized the micro- and nanostructures within cross-linked hydrogels by examining SHG and TEM images respectively. As detected in the SHG images, glycolaldehyde- and glyceraldehyde-modified 5-10 μm "fiberlike" collagen structures to longer, 20 μm and more, aggregated strands while EDC had minimal effect on the microstructure. TEM revealed that glycolaldehyde and glyceraldehyde either completely eliminated collagen's characteristic native fibrillar striations or generated uncharacteristic fibrils with extensions. EDC preserved the native striation patterns, decreased the fibril diameters and effectively homogenized the fibrils within hydrogels assembled at 1.8-4.68 g/L collagen concentrations and 37 °C. Our findings provide a clear understanding on how different cross-linking reagents have very different effects on the collagen hydrogels. This understanding is critical for advancing tissue engineering and wound healing applications.

Ordered collagen membranes: production and characterization

A collagen membrane with microscopic order is presented. The membranes were produced with acid-soluble collagen, using two different methods to obtain orientation. The product was characterized by mean of UV and IR spectra, scanning electronic microscopy, optical microscopy and laser diffractometry. The results clearly show a high level of order in the membranes obtained by both techniques. Permeability for rifamycin, ascorbic acid and NaCl was also measured. Due to the characteristics of the membranes, they have a potential application for treatment of surface injuries.

UV-vis and FT-IR spectra of ultraviolet irradiated collagen in the presence of antioxidant ascorbic acid

The influence of deleterious UV radiation on collagen molecules in the absence and presence of ascorbic acid using UV-vis and FT-IR spectroscopy has been studied. Intensity of UV-vis absorption spectrum of collagen with a maximum at 275 m due to the aromatic residues (tyrosine and phenylalanine) increases with the increasing dose of UV radiation. This effect is significantly hindered in the presence of antioxidant ascorbic acid. Intensities of FT-IR bands (amide A, B, I and II) of collagen decrease with the increase of the UV radiation dosage. Intensities of bands are also decreased in the presence of ascorbic acid. Results suggest that increasing the concentration of ascorbic acid increases the photo-stability of collagen, and the collagen becomes less sensitive to UV radiation. It is possible that hydrogen bonds form between the groups N-H of collagen and C=O of ascorbic acid. It is believed that under UV radiation free radicals appear in acid soluble collagen and resulting in photodegradation of the macromolecule restore due to the ability of ascorbic acid donating one or two electrons. Increasing the dose of radiation causes more molecules of ascorbic acid to slow down, and their antioxidant effect is diminished accordingly.

Nanomechanical characterization of micro/nanofiber reinforced type I collagens

To function properly in the rigorous tissue environment, implanted scaffolds for tissue engineering are required to meet certain standards of strength and mechanical integrity. However, the soft nature and moisture condition of biomaterials impose great challenges to many existing techniques and instrumentations for measuring their mechanical properties at micro/nano scale. In this work, we demonstrate the testing methodologies of micro/nano fiber reinforced type I collagens, and obtain basic mechanical property data of two types of modified collagens-micro carbon fiber reinforced collagen (MCFR) and nano collagen fiber reinforced collagen (NCFR). Results show that mechanical properties of collagen tissues can be enhanced by reinforcing nano collagen fibers but weakened by micro carbon fiber reinforcements. Mechanisms are discussed on how natures of reinforcing fibers affect reinforcement to the collagen matrix, as well as how reinforcements behave within the collagen matrix in response to mechanical strain.

Mechanical properties of UV irradiated rat tail tendon (RTT) collagen

The mechanical properties of RTT collagen tendon before and after UV irradiation have been investigated by mechanical testing (Instron). Air-dried tendon were submitted to treatment with UV irradiation (wavelength 254 nm) for different time intervals. The changes in such mechanical properties as breaking strength and percentage elongation have been investigated. The results have shown, that the mechanical properties of the tendon were greatly affected by time of UV irradiation. Ultimate tensile strength and ultimate percentage elongation decreased after UV irradiation of the tendon. Increasing UV irradiation leads to a decrease in Young's modulus of the tendon.

Microtensile testing of collagen fibril for cardiovascular tissue engineering

As a candidate scaffold material for cardiac tissue engineering, Type I collagen material shows different mechanical properties due to the differences in the structural features such as orientation of fibril alignment and the environmental factors such as ultraviolet (UV) irradiation. In this article one-dimensional tensile stress tests were performed with the use of a nanoscale tensile tester on four groups of Type I collagen samples that were differentiated in terms of fibril orientation and/or UV irradiation. The collagen surface structure was studied with the use of an atomic force microscope (AFM). Effects of fibril orientation and UV irradiation on their mechanical properties were investigated. The mechanical properties and deformation mechanisms are discussed in conjunction with collagen structure, fibril orientation, and dispersion of the generated crosslinking by UV irradiation.

Noninvasive in situ evaluation of osteogenic differentiation by time-resolved laser-induced fluorescence spectroscopy

The clinical implantation of bioengineered tissues requires an in situ nondestructive evaluation of the quality of tissue constructs developed in vitro before transplantation. Time-resolved laser-induced fluorescence spectroscopy (TR-LIFS) is demonstrated here to noninvasively monitor the formation of osteogenic extracellular matrix (ECM) produced by putative stem cells (PLA cells) derived from human adipose tissue. We show that this optical spectroscopy technique can assess the relative expression of collagens (types I, III, IV, and V) within newly forming osteogenic ECM. The results are consistent with those obtained by conventional histochemical techniques (immunofluorescence and Western blot) and demonstrate that TR-LIFS is a potential tool for monitoring the expression of distinct collagen types and the formation of collagen cross-links in intact tissue constructs.

Time-resolved fluorescence spectra of arterial fluorescent compounds: reconstruction with the Laguerre expansion technique

The time-resolved fluorescence spectra of the main arterial fluorescent compounds were retrieved using a new algorithm based on the Laguerre expansion of kernels technique. Samples of elastin, collagen and cholesterol were excited with a pulsed nitrogen laser and the emission was measured at 29 discrete wavelengths between 370 and 510 nm. The expansion of the fluorescence impulse response function on the Laguerre basis of functions was optimized to reproduce the observed fluorescence emission. Collagen lifetime (5.3 ns at 390 nm) was substantially larger than that of elastin (2.3 ns) and cholesterol (1.3 ns). Two decay components were identified in the emission decay of the compounds. For collagen, the decay components were markedly wavelength dependent and hydration dependent such that the emission decay became shorter at higher emission wavelengths and with hydration. The decay characteristics of elastin and cholesterol were relatively unchanged with wavelength and with hydration. The observed variations in the time-resolved spectra of elastin, collagen and cholesterol were consistent with the existence of several fluorophores with different emission characteristics. Because the compounds are present in different proportions in healthy and atherosclerotic arterial walls, characteristic differences in their time-resolved emission spectra could be exploited to assess optically the severity of atherosclerotic lesions.

Photochemistry of type I acid-soluble calf skin collagen: dependence on excitation wavelength

Although previous studies have demonstrated that the predominant photochemistry of type I collagen under 254 nm irradiation may be attributed either to direct absorption by tyrosine/phenylalanine or to peptide bonds, direct collagen photochemistry via solar UV wavelengths is much more likely to involve several age- and tissue-related photolabile collagen fluorophores that absorb in the latter region. In this study, we compare and contrast results obtained from irradiation of a commercial preparation of acid-soluble calf skin type I collagen in solution with UVC (primarily 254 nm), UVA (335-400 nm) and broad-band solar-simulating radiation (SSR; 290-400 nm). Excitation spectroscopy and analysis of photochemically induced disappearance of fluorescence (fluorescence fading) indicates that this preparation has at least four photolabile fluorescent chromophores. In addition to tyrosine and L-3,4-dihydroxyphenylalanine, our sample contains two other fluorophores. Chromophore I, with emission maximum at 360 nm, appears to be derived from interacting aromatic moieties in close mutual proximity. Chromophore II, with broad emission at 430-435 nm, may be composed of one or more age-related molecules. Collagen fluorescence fading kinetics are sensitive to excitation wavelength and to conformation. Under UVC, chromophore I fluorescence disappears with second-order kinetics, indicating a reaction between two proximal like molecules. Adherence to second-order kinetics is abrogated by prior denaturation of the collagen sample. A new broad, weak fluorescence band at 400-420 nm, attributable to dityrosine, forms under UVC, but not under solar radiation. This band is photolabile to UVA and UVB wavelengths.(ABSTRACT TRUNCATED AT 250 WORDS)

Desensitization of rabbit skin by repeated exposure to UV-visible light of sites injected with Rose Bengal

We have shown in a previous paper that irradiation of rabbit skin sites injected with Rose Bengal (RB) produces immediate increase in vascular permeability and accumulation of PMNs. Studies on the development of temporary tolerance and the biological parameters related to the development of such tolerant state by repeated exposure to light of RB-injected sites are reported here. The increase in VP and PMN migration induced by RB (10 nmol) are of an immediate nature, i.e., occur within the first 3 h of irradiation, and the reaction subsides gradually after 24 h. When such moderate insult is repeated, the skin becomes tolerant to subsequent exposure to light in the presence of RB. This tolerant state is temporary, i.e., the desensitized sites are fully recovered in 72 h. The loss of responsiveness of RB-injected sites previously exposed to light was not due to diffusion of the injected dye from the sites since reinjected sites also showed reduced response and the sites injected three days before but not irradiated showed normal response. The sites that were made tolerant to RB-induced phototoxic reactions, when injected with compound 48/80, an agent known to degranulate mast cells, did not show an increase in VP. This suggests that either the mast cells were depleted from the sites or the mast cells in the sites were rendered refractory by previous exposure to light. It was also found that the sites made tolerant to RB plus light were unresponsive to exogenously injected histamine. The sites tolerant to RB plus light when injected with zymosan-activated serum (ZAS) did not stimulate the migration of PMNs. This loss of chemotactic response to ZAS may have relevance to photodamage of vascular endothelium. These observations are discussed in relation to the development of the tolerant state by repeated exposures to subthreshold doses of light in solar urticaria.

Cross-linking and fluorescence changes of collagen by glycation and oxidation

The non-enzymatic glucosylation of collagen in vivo and in vitro produces blue-fluorescent cross-links very slowly. The mechanism of their formation is unknown. We investigated the role of oxidation in glycation. When native fluorescent collagen from old-rat tail tendon and its CNBr peptides were oxidized by chemically generated singlet oxygen, cross-linking occurred immediately, and the cross-linked products showed an increased blue fluorescence. Further cross-linking and development of blue fluorescence also were accelerated by singlet oxygen when oxidizing in vitro glucosylated collagen CNBr peptides. It was noted that the blue fluorescence developed at the expense of a near-UV fluorescence. This near-UV fluorophore, which is also present in native collagen, was found to be produced by the in vitro glucosylation of collagen and during the cross-linking by glucosylation was slowly converted to the blue fluorophore. These changes indicate the autoxidation of near-UV fluorescent intermediates to blue fluorescent cross-links during glucosylation. Non-enzymatic fructosylation, which occurs in vivo in certain proteins, was more effective than glucosylation in forming fluorophores and cross-links with collagen in vitro. Fructosylated fluorophores were found different from glucosylated products in their oxidation reactivities with singlet oxygen.

Cross-linking of collagen CNBr peptides by ozone or UV light

Insoluble collagen from rat tail tendon was digested with cyanogen bromide. The resultant peptides were dissolved in 0.1% SDS solution and separated by gel filtration and gel electrophoresis. Cross-linking occurred in CNBr-cleaved peptides when they were exposed to ozone or biologically effective UV (300 nm) radiation. The enhancement of a blue fluorescence at 430 nm (excited at 350 nm) was found to be associated with oxidized, cross-linked peptides. Polymeric peptides, formed in collagen with aging, also exhibited enhanced blue fluorescence.

Photolysis and ozonolysis of (iso)desmosine-containing crosslinked peptides from porcine aorta elastin

This report describes the use of photolysis and ozonolysis as a means of achieving complete cleavage of the pyridinium ring of (iso)desmosine in crosslinked elastin peptides. Although photolysis leads to the opening of the ring with concomitant formation of lysine, the peptide chains remain attached. Subsequent ozonolysis is able to completely achieve the cleavage of the rest of the ring skeleton, thus leading to the separation of the peptide chains. Formation of new amino acids, i.e. alpha-aminoadipic and glutamic acids, is emphasized. Localization of these amino acids within the released peptides should be of help in structural investigations on the crosslinking zones involving either isodesmosine or desmosine. However, other amino acids such as tyrosine and phenylalanine are sensitive to this procedure and side reactions occur which are responsible for peptide bond cleavage with the formation of breakdown products.