Synthesis and characterization of functional calcium-phosphate-chitosan adsorbents for fluoride removal from water

Functional calcium-phosphate-chitosan adsorbents for fluoride (F-) removal from water with different proportions of calcium (0.7 or 1.4 % w/v) were synthesized by: i) ionotropic gelation technique followed by drying in a convection oven (IGA) or freeze drying (FDA); ii) freeze-gelation followed by drying in a convection oven (FGA). Adsorbents were analyzed by SEM-EDX and FTIR- ATR. F- removal percentages higher than 45 % were obtained with calcium-phosphate-chitosan adsorbents for an initial F- concentration of 9.6 mg L-1. Optimal conditions for F- removal were attained, using calcium-phosphate- chitosan adsorbents synthesized by ionotropic gelation with 0.7 % of Ca (IGA0.7). Under these conditions, initial F- concentration of 5 mg L-1, was reduced below the maximum limit of 1.5 mg L-1 established by WHO. Regeneration of IGA0.7 was achieved in acid media. The performance of IGA0.7 was slightly reduced in the presence of coexisting anions (nitrate, carbonate, arsenate). Adsorption kinetics was represented satisfactorily by the pseudo-second order equation; Langmuir isotherm provided the best fit to the equilibrium data and IGA0.7 exhibited a maximum F- adsorption capacity qL = 132.25 mg g-1. IGA0.7 particles were characterized by thermogravimetry coupled to FTIR, XRD, XPS and SEM-EDX. The calcium-phosphate-chitosan adsorbents constitute a suitable and emerging material for water defluorination.

Application of manganese oxide-based materials for arsenic removal: A review

In the context of growing arsenic (As) contamination in the world, there is an urgent need for an effective treatment approach to remove As from the environment. Industrial wastewater is one of the primary sources of As contamination, which poses significant risks to both microorganisms and human health, as the presence of As can disrupt the vital processes and synthesis of crucial macromolecules in living organisms. The global apprehension regarding As presence in aquatic environments persists as a key environmental issue. This review summarizes the recent advances and progress in the design, strategy, and synthesis method of various manganese-based adsorbent materials for As removal. Occurrence, removal, oxidation mechanism of As(III), As adsorption on manganese oxide (MnOx)-based materials, and influence of co-existing solutes are also discussed. Furthermore, the existing knowledge gaps of MnOx-based adsorbent materials and future research directions are proposed. This review provides a reference for the application of MnOx-based adsorbent materials to As removal.

In vitro analysis of iron oxide (Fe3O4) nanoparticle mediated degradation of polycyclic aromatic hydrocarbons (PAHs) and their antimicrobial activity

To degrade anthracene, magnetite nanoparticles were produced using a simple co-precipitation process. The fabricated nanoparticles have been analyzed for structural and optical properties. XRD examination revealed that the produced Fe3O4 nanoparticles were cubic phase, having a mean crystallite dimension of 18.84 nm. DLS determined the hydrodynamic diameter of Fe3O4 nanoparticles to be 182 nm. UV-Vis research revealed that Fe3O4 nanoparticles absorb at 390 nm. A peak at 895 cm-1 in the FT-IR study indicated the metal-oxygen connection. The synthesized Fe3O4 nanoparticles demonstrated an effective photocatalytic performance towards anthracene degradation and was found to be 86.55%. Furthermore, Fe3O4 nanoparticles showed the highest antimicrobial activity against Bacillus subtilis was 19.43 mm. The present study is the first and foremost study determining the dual role of Fe3O4 nanoparticles towards bioremediation and biomedical applications.

Plasmonic nanoparticle's anti-aggregation application in sensor development for water and wastewater analysis

Colorimetric sensors have emerged as a powerful tool in the detection of water pollutants. Plasmonic nanoparticles use localized surface plasmon resonance (LSPR)-based colorimetric sensing. LSPR-based sensing can be accomplished through different strategies such as etching, growth, aggregation, and anti-aggregation. Based on these strategies, various sensors have been developed. This review focuses on the newly developed anti-aggregation-based strategy of plasmonic nanoparticles. Sensors based on this strategy have attracted increasing interest because of their exciting properties of high sensitivity, selectivity, and applicability. This review highlights LSPR-based anti-aggregation sensors, their classification, and role of plasmonic nanoparticles in these sensors for the detection of water pollutants. The anti-aggregation based sensing of major water pollutants such as heavy metal ions, anions, and small organic molecules has been summarized herein. This review also provides some personal insights into current challenges associated with anti-aggregation strategy of LSPR-based colorimetric sensors and proposes future research directions.

Cationic Microbubbles for Non-Selective Binding of Cavitation Nuclei to Bacterial Biofilms

The presence of multi-drug resistant biofilms in chronic, persistent infections is a major barrier to successful clinical outcomes of therapy. The production of an extracellular matrix is a characteristic of the biofilm phenotype, intrinsically linked to antimicrobial tolerance. The heterogeneity of the extracellular matrix makes it highly dynamic, with substantial differences in composition between biofilms, even in the same species. This variability poses a major challenge in targeting drug delivery systems to biofilms, as there are few elements both suitably conserved and widely expressed across multiple species. However, the presence of extracellular DNA within the extracellular matrix is ubiquitous across species, which alongside bacterial cell components, gives the biofilm its net negative charge. This research aims to develop a means of targeting biofilms to enhance drug delivery by developing a cationic gas-filled microbubble that non-selectively targets the negatively charged biofilm. Cationic and uncharged microbubbles loaded with different gases were formulated and tested to determine their stability, ability to bind to negatively charged artificial substrates, binding strength, and, subsequently, their ability to adhere to biofilms. It was shown that compared to their uncharged counterparts, cationic microbubbles facilitated a significant increase in the number of microbubbles that could both bind and sustain their interaction with biofilms. This work is the first to demonstrate the utility of charged microbubbles for the non-selective targeting of bacterial biofilms, which could be used to significantly enhance stimuli-mediated drug delivery to the bacterial biofilm.

Environmental application of amine functionalised magnetite nanoparticles grafted graphene oxide chelants

This study proposed a two-step method involving hydrothermal and electrostatic self-assembly processes for synthesising an amine-functionalised magnetic ligand graphene oxide-based nanocomposite (EDTA@Fe₃O₄@GO). The amine groups were successfully attached to the surface of iron (II, III) oxide (Fe₃O₄), which were embedded on the surface of graphene oxide (GO) (Fe₃O₄@GO). This EDTA@ Fe₃O₄@GO nanocomposite was used as a chelating agent to bind the toxic heavy metal ions. EDTA@Fe₃O₄@GO demonstrated the synergistic effect between the large surface area and magnetic behaviour of Fe₃O₄@GO and the chelating effect of EDTA, and it showed higher efficiency than the individual GO and Fe₃O₄. The possible structural and compositional characteristics were proposed based on Fourier transform infrared spectra (FTIR), X-ray diffraction (XRD), scanning electron microscope (SEM), Brunauer-Emmett-Teller (BET) and Raman spectroscopy analysis. The outcomes revealed the mechanism behind the excellent As(V) adsorption onto EDTA@Fe₃O₄@GO. The adsorption process was studied by fitting the experimental data obtained into various kinetic and isotherm models. The pseudo-second-order (PSO) kinetic model and the Freundlich isotherm model (FIM) were found to be the best fit models for the removal of As(V) by EDTA@Fe₃O₄@GO. EDTA@Fe₃O₄@GO has the utmost adsorption capacity of 178.4 mg/g. Furthermore, the EDTA@Fe₃O₄@GO nanocomposite is reusable, and it showed excellent adsorption capacity up to 5 cycles. This study has provided insight into the potential of EDTA@Fe₃O₄@GO and its applications in large-scale wastewater treatment.

Development of Adsorptive Membranes for Selective Removal of Contaminants in Water

The presence of arsenic and ammonia in ground and surface waters has resulted in severe adverse effects to human health and the environment. Removal technologies for these contaminants include adsorption and membrane processes. However, materials with high selectivity and pressure stability still need to be developed. In this work, adsorbents and adsorptive membranes were prepared using nanostructured graphitic carbon nitride decorated with molecularly imprinted acrylate polymers templated for arsenate and ammonia. The developed adsorbent removed arsenate at a capacity and selectivity similar to commercial ion-exchange resins. Ammonia was removed at higher capacity than commercial ion exchange resins, but the adsorbent showed lower selectivity. Additionally, the prepared membranes removed more arsenate and ammonia than non-imprinted controls, even in competition with abundant ions in water. Further optimization is required to improve pressure stability and selectivity.

Cu and As(V) Adsorption and Desorption on/from Different Soils and Bio-Adsorbents

This research is concerned with the adsorption and desorption of Cu and As(V) on/from different soils and by-products. Both contaminants may reach soils by the spreading of manure/slurries, wastewater, sewage sludge, or pesticides, and also due to pollution caused by mining and industrial activities. Different crop soils were sampled in A Limia (AL) and Sarria (S) (Galicia, NW Spain). Three low-cost by-products were selected to evaluate their bio-adsorbent potential: pine bark, oak ash, and mussel shell. The adsorption/desorption studies were carried out by means of batch-type experiments, adding increasing and individual concentrations of Cu and As(V). The fit of the adsorption data to the Langmuir, Freundlich, and Temkin models was assessed, with good results in some cases, but with high estimation errors in others. Cu retention was higher in soils with high organic matter and/or pH, reaching almost 100%, while the desorption was less than 15%. The As(V) adsorption percentage clearly decreased for higher As doses, especially in S soils, from 60−100% to 10−40%. The As(V) desorption was closely related to soil acidity, being higher for soils with higher pH values (S soils), in which up to 66% of the As(V) previously adsorbed can be desorbed. The three by-products showed high Cu adsorption, especially oak ash, which adsorbed all the Cu added in a rather irreversible manner. Oak ash also adsorbed a high amount of As(V) (>80%) in a rather non-reversible way, while mussel shell adsorbed between 7 and 33% of the added As(V), and pine bark adsorbed less than 12%, with both by-products reaching 35% desorption. Based on the adsorption and desorption data, oak ash performed as an excellent adsorbent for both Cu and As(V), a fact favored by its high pH and the presence of non-crystalline minerals and different oxides and carbonates. Overall, the results of this research can be relevant when designing strategies to prevent Cu and As(V) pollution affecting soils, waterbodies, and plants, and therefore have repercussions on public health and the environment.

Fe(III)–Chitosan Microbeads for Adsorptive Removal of Cr(VI) and Phosphate Ions

Fe(III)–chitosan microbeads (Fe–CTB) were prepared using a chemical coprecipitation method. SEM–EDX, FTIR, XRD, TGA, BET, and pH pzc were performed for the characterization of the adsorbent. Various parameters were optimized as pH, adsorption time, adsorbent dose, initial Cr(VI), and PO43− ion concentration and the effect of assorted ions for adsorption studies. Fe–CTB microbeads revealed more than 80% detoxification for a 100 mg L−1 initial concentration at pH 3 with 60 min stirring of Cr(VI) and PO43− ion having adsorption capacities of 34.15 and 32.27 mg g−1, respectively. The adsorption process for Cr(VI) and PO43− ion followed the monolayer adsorption as they favored the Langmuir isotherm model. Kinetic and thermodynamic studies’ emphasis on the adsorption process was spontaneous and exothermic with pseudo-second-order kinetics for both adsorbates. The microbeads were found to be reusable in multiple cycles.

Kinetics and mechanism of synergistic adsorption and persulfate activation by N-doped porous carbon for antibiotics removals in single and binary solutions

Porous carbon serves as a green material for efficient wastewater purification by adsorption and advanced oxidation processes. However, a clear understanding of the simultaneous removal of multiple pollutants in water is still ambiguous. Herein, the synergistic effect of adsorption and peroxydisulfate (PS) activation on kinetics and mechanism of removing single and binary antibiotic pollutants, sulfamethoxazole (SMX) and ibuprofen (IBP), from water by biomass-derived N-doped porous carbon was investigated. Our findings suggest that adsorption contributed to efficient removals of SMX/IBP. Comparative quenching experiments and electrochemical analysis demonstrated that hydroxyl (•OH) and sulfate (SO₄^•-) radicals, as well as singlet oxygen (¹O₂) led to the catalytic degradation of SMX, while only ¹O₂ reacted for IBP oxidation. Superoxide ion (O₂^•-) radicals were not related to SMX/IBP degradation. Electron transfer pathway accounted for PS activation but was not involved in direct SMX/IBP oxidation. Only slight differences were found between the degradation kinetics of SMX and IBP in the binary and single SMX or IBP solutions. This arose from the non-selective effect of adsorption and ¹O₂ attack for SMX/IBP removal, and the weak selective oxidation process of SMX by •OH and SO₄^•-. This study provides a new viewpoint on the role of adsorption in catalysis and enriches the mechanistic study of multi-component antibiotic degradation.

Fluoride ions sorption using functionalized magnetic metal oxides nanocomposites: a review

Fluoride is an anionic pollutant found superfluous in surface or groundwater as a result of anthropogenic actions from improper disposal of industrial effluents. In drinking water, superfluous fluoride has been revealed to trigger severe health problems in humans. Hence, developing a comprehensive wastewater decontamination process for the effective management and preservation of water contaminated with fluoride is desirable, as clean water demand is anticipated to intensify considerably over the upcoming years. In this regard, there have been increased efforts by researchers to create novel magnetic metal oxide nanocomposites which are functionalized for the remediation of wastewater owing to their biocompatibility, cost-effectiveness, relative ease to recover and reuse, non-noxiousness, and ease to separate from solutions using a magnetic field. This review makes an all-inclusive effort to assess the effects of experimental factors on the sorption of fluoride employing magnetic metal oxide nanosorbents. The removal efficiency of fluoride ions onto magnetic metal oxides nanocomposites were largely influenced by the solution pH and ions co-existing with fluoride. Overall, it was noticed from the reviewed researches that the maximum sorption capacity using various metal oxides for fluoride sorption was in the order of aluminium oxides >cerium oxides > iron oxides > magnesium oxides> titanium oxides, and most sorption of fluoride ions was inhibited by the existence of phosphate trailed by sulphate. The mechanism of fluoride sorption onto various sorbents was due to ion exchange, electrostatic attraction, and complexation mechanism.

Effect of solution chemistry on aqueous As(III) removal by titanium salts coagulation

Solution chemistry is of great importance to the removal of arsenic by coagulation through influencing the speciation of arsenic, the in situ precipitation of metal salts coupled with the adsorption and coprecipitation behavior of arsenic during coagulation. While the researches on the influence of solution chemistry in As(III) removal by titanium salts, a promising candidate for drinking water treatment was still deficient. Batch tests were performed to evaluate the removal of As(III) by titanium salts coagulation under solution chemistry influences. The results indicated that As(III) removal by Ti(SO₄)₂ and TiCl₄ increased first and then decreased with the rising of solution pH from 4 to 10. TiCl₄ preformed better in As(III) removal than Ti(SO₄)₂ at pH 4-8, but the opposite trends were observed at pH 9-10. XPS analysis indicated that the involvement of surface hydroxyl groups was primarily responsible for As(III) adsorption on Ti(IV) precipitates. As(III) removal was inhibited in the presence of SO₄^2- mainly by competitive adsorption, especially at elevated SO₄^2- concentration under acidic and alkaline conditions. F^- exerted a greater suppressive effect than SO₄^2- via indirectly hindering Ti(IV) precipitate formation, and through direct competitive adsorption with H₃AsO₃, the inhibitive effect increased as F^- concentration increased and depended highly on solution pH. As(III) removal was promoted by co-existing Fe(II) primarily through the facilitation of Ti(IV) precipitation, especially under neutral and alkaline conditions, while it was inhibited to a different extent by the presence of high-concentration Mn(II) possibly via competitive adsorption. The presence of Ca²⁺ and Mg²⁺ enhanced the removal of As(III), but the positive effect did not increase as ionic concentration elevated.

Sea urchin-like FeOOH functionalized electrochemical CNT filter for one-step arsenite decontamination

Advanced nanotechnologies for efficient arsenic decontamination remain largely underdeveloped. The most abundant inorganic arsenic species are neutrally-charged arsenate, As(III), and negatively-charged arsenite, As(V). Compared with As(V), As(III) is 60 times more toxic and more difficult to remove due to high mobility. Herein, an electrochemical filtration system was rationally designed for one-step As(III) decontamination. The key to this technology is a functional electroactive carbon nanotube (CNT) filter functionalized with sea urchin-like FeOOH. With the assistance of electric field, CNT-FeOOH anodic filter can in situ transform As(III) to less toxic As(V) while passing through. Then, as-produced As(V) could be effectively sequestrated by FeOOH. The sufficient exposed sorption sites, flow-through design, and filter's electrochemical reactivity synergistically guaranteed a rapid arsenic removal kinetic. The underlying working mechanism was unveiled based on systematic experimental investigations and theoretical calculations. The system efficacy can be adapted across a wide pH range and environmental matrixes. Exhausted CNT-FeOOH filters could be effectively regenerated by chemical washing with diluted NaOH solution. Outcomes of the present study are dedicated to provide a straightforward and effective strategy by integrating electrochemistry, nanotechnology, and membrane separation for the removal of arsenic and other similar heavy metals from water bodies.

Coconut shell derived ZnCl2 activated carbon for malachite green dye removal

The coconut-based agricultural wastes have gained wide attention as an alternative adsorbent for the removal of diverse pollutants from the industrial effluents. This paper presents the zinc chloride activation of adsorbent carbon and the utilization as an adsorbent for the removal of malachite green dye from aqueous solution. The characterisation of activated carbon was performed to get an insight into the adsorption mechanism. The ZnCl₂ activated carbon acquired a higher specific surface area (544.66 m² g^-1) and stability (-32.6 mV). The impact of process parameters including contact time (20-220 min) and initial dye concentration (20-80 mg L^-1) were evaluated on the effectiveness of activated carbon for dye removal. The results concluded that zinc chloride activated carbon showed a significant dye adsorption (39.683 mg g^-1) at an initial concentration of 20 mg L^-1 after 3 hours. Based on the correlation coefficient (R²), the Freundlich isotherm model (0.978-0.998) was best fitted for the experimental data followed by the intraparticle diffusion model (0.88-0.929) as the most appropriate model for malachite green dye removal. Additionally, the energy and thermogravimetric analysis portrayed the suitability of the carbon material to be used as an energy alternative to coal.

Phosphate removal from wastewater using novel renewable resource-based, cerium/manganese oxide-based nanocomposites

Nanocomposites containing mixed metal oxides show excellent phosphate removal results and are better compared to individual metal oxides. In this research, cerium/manganese oxide nanocomposites, embedded on the surface of modified cellulose pine wood shaving, were synthesized by a simple technique that is both eco-friendly and economically feasible. No toxic or petroleum chemicals were employed during preparation. Scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), surface area analysis, and attenuated total reflectance Fourier-transform infrared (ATR-FTIR) spectroscopy were performed to study the shape and size of nanocomposites as well as composition of elements present on the surface of the nanocomposites. Adsorption isotherm (Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich) and kinetic studies (pseudo first and second-order, Elovich and Weber-Morris) were carried out to determine the adsorption mechanism for phosphate removal from contaminated water. The maximum adsorption capacity of nanocomposites was found to be 204.09 mg/g, 174.42 mg/g, and 249.33 mg/g for 100 mg, 300 mg, and 500 mg, respectively. The results indicate that the nanocomposites were able to decrease the phosphorus concentration from 10 to 0.01 ppm, below the threshold limit required by EPA guidelines in the USA. We also demonstrated that the media could be regenerated and reused five times without loss of performance.

Effect Factor of Arsenite and Arsenate Removal by a Manufactured Material: Activated Carbon-Supported Nano-TiO2

Carbon substrate-supported nano-TiO2 (a manufactured material) was prepared in this study for arsenic removal. The removal rates of arsenic were evaluated by batch tests under several simulation conditions including pH, ionic strength, and adsorbent dosage. Results showed that As(III) and As(V) adsorption reached equilibrium within 10 hours (pH = 8 and ionic strength 0.5 mol/L). At pH = 8, maximum adsorption efficiency was discovered for the adsorbent. Removal rate was proportional to the increase in ionic strength. The removal data were satisfactorily fitted to the pseudo-second-order kinetic model (R2 > 0.9990) and Freundlich equation (R2 ≥ 0.9600) for adsorption thermodynamic behaviors. New material showed more effective adsorption performance for As(V) than for As(III). It was found that 15.1800 mg/g As(V) and 13.3800 mg/g As(III) were adsorbed, respectively. In addition, material properties were studied including the structure of crystallinity, surface morphology, functional groups, and surface texture by XRD, TEM/SEM, FTIR, and BET methods, respectively. XRD result showed supported nano-TiO2 had the anatase phase. The size of the microparticle was around 52 nm. BET results indicated that material surface areas, pore volume, and pore size diameter were 371.17 m2/g, 0.35 cm3/g, and 11.70 nm, respectively. FTIR spectrum indicated that several functional groups (OH−, Ti-O) existing in supported nano-TiO2 may facilitate the adsorption efficiency. Mechanistically, supported nano-TiO2 played a key role in promoting adsorption efficiency and converting As(III) to As(V). Results indicated that the investigated adsorbents possessed an excellent arsenic removal capability.

Bio-inspired materials for defluoridation of water: A review

The polluted water sources pose a serious issue concerning the various health hazards they bring along. Due to various uncontrolled anthropogenic and industrial activities, a great number of pollutants have gained entry into the water systems. Among all the emerging contaminants, anionic species such as fluoride cause a major role in polluting the water bodies because of its high reactivity with other elements. The need for water remediation has led the research community to come up with several physicochemical and electrochemical methods to remove fluoride contamination. Among the existing methods, biosorption using bio and modified biomaterials has been extensively studied for defluoridation, as they are cheap, easily available and effectively recyclable when compared to other methods for defluoridation. Adding on, these materials are non-toxic and are safe to use compared to many other synthetic materials that are toxic and require high-cost design requirements. This review focuses on the recent developments made in the defluoridation techniques by biosorption using bio and modified biomaterials and defines the current perspectives of fluoride removal specifically using biomaterials.

Novel preparation of fungal conidiophores biomass as adsorbent for removal of phosphorus from aqueous solution

The present study focused on phosphorus adsorption by novel fungal conidiophores biomass in aqueous solution. Fungal Conidiophores biomass was prepared from the fungal strains Aspergillus oryzae (YFK) and Fusarium oxysporum (YVS2). The functional groups and morphology of Conidiophores Biomass (CB) from these strains were characterized by FTIR and SEM. FTIR confirms the presence of alcohol, carboxylic acid, carbon dioxide, cyclic alkene, amine, alkene, fluoro compound, and halo compound groups. Batch mode study was carried out with two CB's such as Aspergillus oryzae CB (ACB) and Fusarium oxysporum CB (FCB) with initial concentration of phosphorus ranging from 20 to 100 mg L^-1. Based on the batch experiments, the adsorption kinetics (pseudo first order and pseudo second order), isotherms (Freundlich and Langmuir models), and thermodynamic (standard entropy, energy, and enthalpy) parameters were calculated. The adsorption kinetics and isotherm studies showed that the adsorption data well fitted with PSO kinetic model. From the isotherm results, it was found that ACB and FCB exhibited highest adsorption capacity 25.64 mg g^-1 and 26.32 mg g^-1 of phosphorus respectively at the optimal condition of pH (7), time (90 min), dose (250 mg), and room temperature (35 °C). Thermodynamics values were found to be endothermic and spontaneous in nature for phosphorus adsorption. Finally, the results suggested that the ACB and FCB are economically feasible cost-effective adsorbent for removal of phosphorus in wastewater treatment. Graphical abstract.

Diatom mediated heavy metal remediation: A review

Exposure to heavy metals is a major threat to aquatic bodies and is a global concern to our four main spheres of the earth viz. atmosphere, biosphere, hydrosphere, and lithosphere. The biosorption of pollutants using naturally inspired sources like microalgae has considerable advantages. Diatoms are the most dominant and diverse group of phytoplankton which accounts for 45% oceanic primary productivity. They perform a pioneer part in the biogeochemistry of metals in both fresh and marine water ecosystems. The diatoms play a significant role in degradation, speciation, and detoxification of chemical wastes and hazardous metals from polluted sites. Herein, an overview is presented about the ability of diatom algae to phycoremediate heavy metals by passive adsorption and active assimilation from their aqueous environments with an emphasis on extracellular and intracellular mechanisms involved in contaminant uptake through the frustules for preventing heavy metal toxicity.

Three-dimensional, printed water-filtration system for economical, on-site arsenic removal

The threat of arsenic contamination to public health, particularly in developing countries, has become a serious problem. Millions of people in their daily lives are still highly dependent on groundwater containing high levels of arsenic, which causes excessive exposure to this toxic element, due to the high cost and lack of water-treatment infrastructures. Therefore, a technique for large-scale treatment of water in rural areas to remove arsenic is needed and should be low-cost, be easily customized, and not rely on electrical power. In this study, in an effort to fulfill those requirements, we introduce a three-dimensional (3D), printed water-filtration system for arsenic removal. Three-dimensional printing can provide a compact, customized filtration system that can fulfill the above-mentioned requirements and that can be made from plastic materials, which are abundant. Armed with the versatility of 3D printing, we were able to design the internal surface areas of filters, after which we modified the surfaces of the 3D, printed filters by using iron (III) oxide as an adsorbent for arsenite. We investigated the effects of the controlled surface area on the flow rate and the deposition of the adsorbent, which are directly related to the adsorption of arsenic. We conducted isotherm studies to quantify the adsorption of arsenic on our 3D, printed filtration system.

Polyethyleneimine-modified biochar for enhanced phosphate adsorption

Biochar, a low-cost porous carbonaceous adsorbent, has low adsorption capacity for anion contaminants. The objective of this study was to improve biochar's ability to adsorb phosphorus (P) through polyethyleneimine (PEI) modification to form an amine-functionalized biochar. Biochars prepared by pyrolysis of bamboo biomass, before and after PEI modification, were characterized using the Fourier transformed infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM), elemental analysis, and batch sorption experiments. The effects of pH, coexisting anions, and ionic strength on P adsorption by PEI-modified biochar were also investigated. Results indicated that PEI was successfully grafted onto biochar which resulted an increase in surface amine group and in P adsorption. The peak of P adsorption occurred at pH of three and adsorption of P was decreased with increasing of ionic strength and when coexisting ions, such as HCO₃^-, SO₄^2-, NO₃^-, and Cl^-, were coexisted. The electrostatic interaction between P and surface functional groups of PEI-modified biochar served as the primary mechanism controlling the adsorption process. These results indicate that chemically functionalized biochar with amine groups can enhance P adsorption.

Sustainability criteria for assessing nanotechnology applicability in industrial wastewater treatment: Current status and future outlook

Application of engineered nanomaterials for the treatment of industrial effluents and to deal with recalcitrant pollutants has been noticeably promoted in recent years. Laboratory, pilot and full-scale studies emphasize the potential of this technology to offer promising treatment options to meet the future needs for clean water resources and to comply with stringent environmental regulations. The technology is now in the stage of being transferred to the real applications. Therefore, the assessment of its performance according to sustainability criteria and their incorporation into the decision-making process is a key task to ensure that long term benefits are achieved from the nano-treatment technologies. In this study, the importance of sustainability criteria for the conventional and novel technologies for the treatment of industrial effluents was determined in a general approach assisted by a fuzzy-Delphi method. The criteria were categorized in technical, economic, environmental and social branches and the current situation of the nanotechnology regarding the criteria was critically discussed. The results indicate that the efficiency and safety are the most important parameters to make sustainable choices for the treatment of industrial effluents. Also, in addition to the need for scaling-up the nanotechnology in various stages, the study on their environmental footprint must continue in deeper scales under expected environmental conditions, in particular the synthesis of engineered nanomaterials and the development of reactors with the ability of recovery and reuse the nanomaterials. This paper will aid to select the most sustainable types of nanomaterials for the real applications and to guide the future studies in this field.