Implant surfaces and interface processes

Drug release control and anti-inflammatory effect of biodegradable polymer surface modified by gas phase chemical functional reaction

The plasma technique has been widely used to modify the surfaces of materials. The purpose of this study was to evaluate the probability of controlling the prednisolone delivery velocity on a polylactic acid (PLA) surface modified by plasma surface treatment. Surface modification of PLA was performed at a low-pressure radio frequency under conditions of 100 W power, 50 mTorr chamber pressure, 100-200 sccm of flow rate, and Ar, O2, and CH4gases. The plasma surface-modified PLA was characterized using scanning emission microscope, x-ray photoelectron spectroscopy (XPS), and contact angle measurements.In vitroevaluations were performed to determine cellular response, drug release behavior, and anti-inflammatory effects. The PLA surface morphology was changed to a porous structure (with a depth of approximately 100 μm) and the surface roughness was also significantly increased. The XPS results demonstrated higher oxygenized carbon contents than those in the non-treated PLA group. The prednisolone holding capacity increased and the release was relatively prolonged in the surface-modified PLA group compared to that in the non-treated PLA group. In addition, cell migration and proliferation significantly increased after PLA treatment alone. The activity of cytokines such as cyclooxygenase-2 (COX-2), tumor necrosis factor-a (TNF-α), interleukin (IL-1β), and IL-6 were considerably reduced in the plasma-treated and prednisolone holding group. Taken together, surface-modified PLA by plasma can provide an alternative approach to conventional physicochemical approaches for sustained anti-inflammatory drug release.

Enhancing the mechanical properties and surface morphology of individualized Ti-mesh fabricated through additive manufacturing for the treatment of alveolar bone defects

Titanium meshes are widely utilized in alveolar bone augmentation, and this study aims to enhance the properties of titanium meshes through heat treatment (HT) and the synergistic finishing technology of electric field and flow field (EFSF). Our findings illustrate that the titanium mesh exhibits improved mechanical properties following HT treatment. The innovative EFSF technique, in combination with HT, has a substantial impact on improving the surface properties of titanium meshes. HT initiates grain fusion and reduces surface pores, resulting in enhanced tensile and elongation properties. EFSF further enhances these improvements by significantly reducing surface roughness and eliminating adhered titanium powder, a byproduct of selective laser melting printing. Increased hydrophilicity and surface-free energy are achieved after EFSF treatment. Notably, the EFSF-treated titanium mesh exhibits reduced bacterial adhesion and is non-toxic to osteoblast proliferation. These advancements increase its suitability for clinical alveolar bone augmentation.

Electrodeposited Zinc Coatings for Biomedical Application: Morphology, Corrosion and Biological Behaviour

The improvement of biodegradable metals is currently an active and promising research area for their capabilities in implant manufacturing. However, controlling their degradation rate once their surface is in contact with the physiological media is a challenge. Surface treatments are in the way of addressing the improvement of this control. Zinc is a biocompatible metal present in the human body as well as a metal widely used in coatings to prevent corrosion, due to its well-known metal protective action. These two outstanding characteristics make zinc coating worthy of consideration to improve the degradation behaviour of implants. Electrodeposition is one of the most practical and common technologies to create protective zinc coatings on metals. This article aims to review the effect of the different parameters involved in the electrochemical process on the topography and corrosion characteristics of the zinc coating. However, certainly, it also provides an actual and comprehensive description of the state-of-the-art of the use of electrodeposited zinc for biomedical applications, focusing on their capacity to protect against bacterial colonization and to allow cell adhesion and proliferation.

Properties of SiCN Films Relevant to Dental Implant Applications

The application of surface coatings is a popular technique to improve the performance of materials used for medical and dental implants. Ternary silicon carbon nitride (SiCN), obtained by introducing nitrogen into SiC, has attracted significant interest due to its potential advantages. This study investigated the properties of SiCN films deposited via PECVD for dental implant coatings. Chemical composition, optical, and tribological properties were analyzed by adjusting the gas flow rates of NH3, CH4, and SiH4. The results indicated that an increase in the NH3 flow rate led to higher deposition rates, scaling from 5.7 nm/min at an NH3 flow rate of 2 sccm to 7 nm/min at an NH3 flow rate of 8 sccm. Concurrently, the formation of N-Si bonds was observed. The films with a higher nitrogen content exhibited lower refractive indices, diminishing from 2.5 to 2.3 as the NH3 flow rate increased from 2 sccm to 8 sccm. The contact angle of SiCN films had minimal differences, while the corrosion rate was dependent on the pH of the environment. These findings contribute to a better understanding of the properties and potential applications of SiCN films for use in dental implants.

Assessing the Cleanliness of Dental Implants Using Scanning Electron Microscopy and Energy-Dispersive X-ray Spectroscopy Analysis-A SEM and EDS In Vitro Study

A wide variety of titanium (Ti) alloy dental implant systems are available and as a result, choosing the correct system has become a challenge. Cleanliness of the dental implant surface affects osseointegration but surface cleanliness may be jeopardized during manufacturing. The purpose of this study was to assess the cleanliness of three implant systems. Fifteen implants per system were examined with scanning electron microscopy to identify and count foreign particles. Particle chemical composition analysis was performed with energy-dispersive X-ray spectroscopy. Particles were categorized according to size and location. Particles on the outer and inner threads were quantitatively compared. A second scan was performed after exposing the implants to room air for 10 min. Carbon, among other elements, was found on the surface of all implant groups. Zimmer Biomet dental implants had higher particle numbers than other brands. Cortex and Keystone dental implants showed similar distribution patterns. The outer surface had higher particle numbers. Cortex dental implants were the cleanest. The change in particle numbers after exposure was not significant (p > 0.05). Conclusion: Most of the implants studied were contaminated. Particle distribution patterns vary with the manufacturer. The wider and outer areas of the implant have a higher probability of contamination.

Calcium Phosphate Functionalization and Applications in Dentistry

The oral and maxillofacial hard tissues support the maxillofacial shape and serve as the foundation for functional activities. Defects in these tissues not only impair patients’ ability to perform their normal physiological functions but also have a significant negative impact on their psychological well-being. Moreover, these tissues have a limited capacity for self-healing, necessitating the use of artificial materials to repair defects. Calcium phosphate is a fine-grained inorganic biomineral found in vertebrate teeth and bones that has a comparable composition to human hard tissues. Calcium phosphate materials are biocompatible, bioactive, and osteogenic for hard tissue repair, despite drawbacks such as poor mechanical qualities, limiting their clinical efficacy and application. With the advancement of materials science and technology, numerous techniques have been developed to enhance the characteristics of calcium phosphate, and one of them is functionalization. Calcium phosphate can be functionally modified by changing its size, morphology, or composition through various preparation processes to achieve multifunctionality and improve physical and chemical properties, biocompatibility, and osteogenic potential. The purpose of this review is to provide new ideas for the treatment of oralmaxillofacial hard tissue defects and deficiencies by summarizing the functionalization strategies of calcium phosphate materials and their applications in dentistry.

Relevant Aspects of Titanium and Zirconia Dental Implants for Their Fatigue and Osseointegration Behaviors

Osseointegration capacity and good mechanical behavior are key to the success of the dental implant. In many investigations, comparisons of properties are made using different dental implant designs and therefore the results can be influenced by the macrodesign of the dental implant. In this work, studies were carried out with the same dental implant model using different roughness and different materials—commercially pure titanium (grade 4) and zirconia. For this purpose, 80 smooth passivated titanium (Ti), 80 smooth zirconia (ZrO₂), and 80 rough passivated titanium (Ti-R) dental implants were used. The samples were characterized by their roughness, wettability, surface energy, residual stresses, and fatigue behavior. The implants were implanted in minipigs for 4 and 12 weeks. The animals were sacrificed, and histological studies were carried out to determine the osseointegration parameters for each of the implantation times. Ti and ZrO₂ dental implants have very similar wettability and surface energy properties. However, the roughness causes a decrease in the hydrophilic character and a decrease of the total surface energy and especially the dispersive component, while the polar component is higher. Due to the compressive residual stresses of alumina sandblasting, the rough dental implant has the best fatigue behavior, followed by Ti and due to the lack of toughness and rapid crack propagation the ZrO₂ implants have the worst fatigue behavior. The bone index contact (BIC) values for 4 weeks were around 25% for Ti, 32% for ZrO₂, and 45% for Ti-R. After 12 weeks the Ti dental implants increased to 42%, for Ti, 43% for ZrO₂, and an important increase to 76% was observed for Ti-R implants. In vivo results showed that the key factor that improves osseointegration is roughness. There was no significant difference between ZrO₂ and Ti implants without sandblasting.

Effect of protein adsorption on the dissolution kinetics of silica nanoparticles

Nanoparticulate systems in the presence of proteins are highly relevant for various biomedical applications such as photo-thermal therapy and targeted drug delivery. These involve a complex interplay between the charge state of nanoparticles and protein, the resulting protein conformation, adsorption equilibrium and adsorption kinetics, as well as particle dissolution. SiO₂ is a common constituent of bioactive glasses used in biomedical applications. In this context, the dissolution behavior of silica particles in the presence of a model protein, bovine serum albumin (BSA), at physiologically relevant pH conditions was studied. Sedimentation analysis using an analytical ultracentrifuge showed that BSA in the supernatant solution is not affected by the presence of silica nanoparticles. However, zeta potential measurements revealed that the presence of the protein alters the particles' charge state. Adsorption and dissolution studies demonstrated that the presence of the protein significantly enhances the dissolution kinetics via interactions of positively charged amino acids in the protein with the negative silica surface and interaction of BSA with dissolved silicate species. Our study provides comprehensive insights into the complex interactions between proteins and oxide nanoparticles and establishes a reliable protocol paving the way for future investigations in more complex systems involving biological solutions as well as bioactive materials.

Titanium Surface Characteristics Induce the Specific Reprogramming of Toll-like Receptor Signaling in Macrophages

Most of the research on titanium-based dental implants (Ti-discs) is focused on how they are able to stimulate the formation of new tissue and/or cytotoxic studies, with very scarce data on their effects on functional responses by immunocompetent cells. In particular, the link between the rewiring of innate immune responses and surface biomaterials properties is poorly understood. To address this, we characterize the functional response of macrophage cultures to four different dental titanium surfaces (MA: mechanical abrasion; SB + AE: sandblasting plus etching; SB: sandblasting; AE: acid etching). We use different Toll-like receptor (TLR) ligands towards cell surface receptors (bacterial lipopolysaccharide LPS for TLR4; imiquimod for TLR7; synthetic bacterial triacylated lipoprotein for TLR2/TLR1) and endosomal membrane receptor (poly I:C for TLR3) to simulate bacterial (cell wall bacterial components) or viral infections (dsRNA and ssRNA). The extracellular and total LDH levels indicate that exposure to the different Ti-surfaces is not cytotoxic for macrophages under resting or TLR-stimulated conditions, although there is a tendency towards an impairment in macrophage proliferation, viability or adhesion under TLR4, TLR3 and TLR2/1 stimulations in SB discs cultures. The secreted IL-6 and IL-10 levels are not modified upon resting macrophage exposure to the Ti-surfaces studied as well as steady state levels of iNos or ArgI mRNA. However, macrophage exposure to MA Ti-surface do display an enhanced immune response to TLR4, TLR7 or TLR2/1 compared to other Ti-surfaces in terms of soluble immune mediators secreted and M1/M2 gene expression profiling. This change of characteristics in cellular phenotype might be related to changes in cellular morphology. Remarkably, the gene expression of Tlr3 is the only TLR that is differentially affected by distinct Ti-surface exposure. These results highlight the relevance of patterned substrates in dental implants to achieve a smart manipulation of the immune responses in the context of personalized medicine, cell-based therapies, preferential lineage commitment of precursor cells or control of tissue architecture in oral biology.

Optimization of Titanium Dental Mesh Surfaces for Biological Sealing and Prevention of Bacterial Colonization

Titanium dental meshes have a wide application in order to ensure the retention of calcium phosphate-based biomaterials to regenerate bone tissue. These meshes are temporary and must grow a soft tissue to prevent bacterial colonization and provide stability. In this work, we aimed to optimize the roughness of the meshes to obtain a good biological seal while maintaining a behavior that did not favor bacterial colonization. To this end, six types of surfaces were studied: machined as a control, polished, sandblasted with three different alumina sizes and sintered. The roughness, contact angles and biological behavior of the samples using fibroblast cultures at 7, 24 and 72 h were determined as well as cytotoxicity studies. Cultures of two very common bacterial strains in the oral cavity were also carried out: Streptococcus sanguinis and Lactobacillus salivarius. The results showed that the samples treated with alumina particles by sandblasting at 200 micrometers were the ones that performed best with fibroblasts and also with the number of bacterial colonies in both strains. According to the results, we see in this treatment a candidate for the surface treatment of dental meshes with an excellent performance.

Into the Tissues: Extracellular Matrix and Its Artificial Substitutes: Cell Signalling Mechanisms

The existence of orderly structures, such as tissues and organs is made possible by cell adhesion, i.e., the process by which cells attach to neighbouring cells and a supporting substance in the form of the extracellular matrix. The extracellular matrix is a three-dimensional structure composed of collagens, elastin, and various proteoglycans and glycoproteins. It is a storehouse for multiple signalling factors. Cells are informed of their correct connection to the matrix via receptors. Tissue disruption often prevents the natural reconstitution of the matrix. The use of appropriate implants is then required. This review is a compilation of crucial information on the structural and functional features of the extracellular matrix and the complex mechanisms of cell–cell connectivity. The possibilities of regenerating damaged tissues using an artificial matrix substitute are described, detailing the host response to the implant. An important issue is the surface properties of such an implant and the possibilities of their modification.

Relevant Aspects of Piranha Passivation in Ti6Al4V Alloy Dental Meshes

Passivation of titanium alloy dental meshes cleans their surface and forms a thin layer of protective oxide (TiO2) on the surface of the material to improve resistance to corrosion and prevent release of ions to the physiological environment. The most common chemical agent for the passivation process of titanium meshes is hydrochloric acid (HCl). In this work, we introduce the use of Piranha solution (H2SO4 and H2O2) as a passivating and bactericidal agent for metallic dental meshes. Meshes of grade 5 titanium alloy (Ti6Al4V) were tested after different treatments: as-received control (Ctr), passivated by HCl, and passivated by Piranha solution. Physical-chemical characterization of all treated surfaces was carried out by scanning electron microscopy (SEM), confocal microscopy and sessile drop goniometry to assess meshes’ topography, elemental composition, roughness, wettability and surface free energy, that is, relevant properties with potential effects for the biological response of the material. Moreover, open circuit potential and potentiodynamic tests were carried out to evaluate the corrosion behavior of the differently-treated meshes under physiological conditions. Ion release tests were conducted using Inductively Coupled Plasma mass spectrometry (ICP-MS). The antibacterial activity by prevention of bacterial adhesion tests on the meshes was performed for two different bacterial strains, Pseudomonas aeruginosa (Gram-) and Streptococcus sanguinis (Gram+). Additionally, a bacterial viability study was performed with the LIVE/DEAD test. We complemented the antibacterial study by counting cells attached to the surface of the meshes visualized by SEM. Our results showed that the passivation of titanium meshes with Piranha solution improved their hydrophilicity and conferred a notably higher bactericidal activity in comparison with the meshes passivated with HCl. This unique response can be attributed to differences in the obtained nanotextures of the TiO2 layer. However, Piranha solution treatment decreased electrochemical stability and increased ion release as a result of the porous coating formed on the treated surfaces, which can compromise their corrosion resistance. Framed by the limitations of this work, we conclude that using Piranha solution is a viable alternative method for passivating titanium dental meshes with beneficial antibacterial properties that merits further validation for its translation as a treatment applied to clinically-used meshes.

Citric Acid in the Passivation of Titanium Dental Implants: Corrosion Resistance and Bactericide Behavior

The passivation of titanium dental implants is performed in order to clean the surface and obtain a thin layer of protective oxide (TiO2) on the surface of the material in order to improve its behavior against corrosion and prevent the release of ions into the physiological environment. The most common chemical agent for the passivation process is hydrochloric acid (HCl), and in this work we intend to determine the capacity of citric acid as a passivating and bactericidal agent. Discs of commercially pure titanium (c.p.Ti) grade 4 were used with different treatments: control (Ctr), passivated by HCl, passivated by citric acid at 20% at different immersion times (20, 30, and 40 min) and a higher concentration of citric acid (40%) for 20 min. Physical-chemical characterization of all of the treated surfaces has been carried out by scanning electronic microscopy (SEM), confocal microscopy, and the 'Sessile Drop' technique in order to obtain information about different parameters (topography, elemental composition, roughness, wettability, and surface energy) that are relevant to understand the biological response of the material. In order to evaluate the corrosion behavior of the different treatments under physiological conditions, open circuit potential and potentiodynamic tests have been carried out. Additionally, ion release tests were realized by means of ICP-MS. The antibacterial behavior has been evaluated by performing bacterial adhesion tests, in which two strains have been used: Pseudomonas aeruginosa (Gram-) and Streptococcus sanguinis (Gram+). After the adhesion test, a bacterial viability study has been carried out ('Life and Death') and the number of colony-forming units has been calculated with SEM images. The results obtained show that the passivation with citric acid improves the hydrophilic character, corrosion resistance, and presents a bactericide character in comparison with the HCl treatment. The increasing of citric acid concentration improves the bactericide effect but decreases the corrosion resistance parameters. Ion release levels at high citric acid concentrations increase very significantly. The effect of the immersion times studied do not present an effect on the properties.

Reactivity of Titanium Dental Implant Surfaces in Simulated Body Fluid

Osseointegration of titanium (Ti) implants in bone is crucial for dental implant treatment. Bacterial challenge possibly leading to peri-implantitis threatens long-term success. For the improvement of osseointegration, an understanding of materials and tissue intervention is needed. This in vitro study analyzed changes of different implant surfaces exposed to simulated body fluid (SBF). Implants were analyzed by scanning electron microscopy/X-ray photoelectron spectroscopy. Supernatants (SNs) were assessed using inductively coupled plasma-mass spectrometry (ICP-MS). Additional calcium (Ca) and phosphate (P) crystals developed (Hank's buffered salt solution (HBSS)) on implants with layered surfaces. ICP of SN demonstrated a decreased Ca/P ratio. After incubation with human serum (HS), layers appeared flattened containing <1% Ca/P. The etched/machined implants showed the formation of a surface transformation layer or coating consisting of crystalline Ca/P precipitations and a decrease in the Ca/P ratio in the supernatant. Incubation in HS induced noncrystalline coverage, and increased Ti/Ca/P was detected in supernatants. HBSS induced crystals on surfaces of modified implants and crystalline covers on nonmodified implants containing Ca/P. The serum did not show the development of HA-like structures but showed dissolving effects. Titanium surfaces show completely altered behavior when incubated in serum-containing SBF.

Biochemical Modification of Titanium Oral Implants: Evidence from In Vivo Studies

The discovery of osseointegration of titanium implants revolutionized the dental prosthesis field. Traditionally, implants have a surface that is processed by additive or subtractive techniques, which have positive effects on the osseointegration process by altering the topography. In the last decade, innovative implant surfaces have been developed, on which biologically active molecules have been immobilized with the aim of increasing stimulation at the implant-biological tissue interface, thus favoring the quality of osseointegration. Among these molecules, some are normally present in the human body, and the techniques for the immobilization of these molecules on the implant surface have been called Biochemical Modification of Titanium Surfaces (BMTiS). Different techniques have been described in order to immobilize those biomolecules on titanium implant surfaces. The aim of the present paper is to present evidence, available from in vivo studies, about the effects of biochemical modification of titanium oral implants on osseointegration.

The early loading of different surface-modified implants: a randomized clinical trial

BACKGROUND

Various surface treatment options have been adopted with the aim to improve osseointegration, reducing the overall treatment time. Implant stability of early loaded implants with different modified surfaces was compared in the present study.

METHODS

Patients were selected from the Department of Oro-Maxillofacial Surgery and Stomatology at Semmelweis University. Patients randomly received SA (alumina sandblasted and acid-etched), NH (bioabsorbable apatite nanocoating) or SLA (large-grit sandblasted and acid-etched) surface implants. Outcome measures were: implant success, implant stability, and periodontal parameters. The implant stability was measured at the time of implant placement (primary stability) and six weeks after (prothesis delivery, secondary stability). Osstell and Periotest were applied to take all the measurements. The primary and secondary stability were compared in the three study groups Finally the periimplant probing depth appearing after three months of loading was checked on 6 points around to the implant-supported prostheses. Shapiro-Wilk and Mann-Whitney tests were used for the comparison between the study groups.

RESULTS

A total of 75 implants with different length and diameter were inserted into various positions. One implant failed spontaneously at the fourth week after implant placement. The survival rate was 98,7%. Comparing the primary and secondary stability values, the data were significantly improved in every groups. The difference was the highest in the NH group, however, this difference was not significant compared to the two other groups. Good periodontal parameters were experienced in all the tested implants, independently by the groups.

CONCLUSIONS

With the limitation of the present study, all the implants showed improved stability six weeks after implant placement. A trend of higher result was found for the NH group. Further studies with longer follow-up are needed to confirm this preliminary results.

TRIAL REGISTRATION

Current Controlled Trials ISRCTN13181677; the date of registration: 04/03/2021. Retrospectively registered.

Protein Adsorption at Nanorough Titanium Oxide Surfaces: The Importance of Surface Statistical Parameters beyond Surface Roughness

The nanoscale surface topography of biomaterials can have strong effects on protein adsorption. While there are numerous surface statistical parameters for the characterization of nanorough surfaces, none of them alone provides a complete description of surface morphology. Herein, a selection of nanorough titanium oxide surfaces has been fabricated with root-mean-square roughness (Sq) values below 2.7 nm but very different surface morphologies. The adsorption of the proteins myoglobin (MGB), bovine serum albumin (BSA), and thyroglobulin (TGL) at these surfaces was investigated in situ by ellipsometry to assess the importance of six of the most common surface statistical parameters. For BSA adsorption, both protein film thickness and time constant of adsorption were found to scale linearly with Sq s. For TGL, however, the same adsorption characteristics depend linearly on the surface skewness (Ssk), which we attribute to the rather extreme size of this protein. Finally, a mixed behavior is observed for MGB adsorption, showing different linear correlations with Sq and Ssk. These results demonstrate the importance of a thorough morphological characterization of the surfaces employed in protein adsorption and possibly also cell adhesion studies.

Atomic Layer Deposition of Bioactive TiO2 Thin Films on Polyetheretherketone for Orthopedic Implants

TiO₂ thin films were deposited on the orthopedic implant material polyetheretherketone (PEEK) by plasma enhanced atomic layer deposition (PEALD) and characterized for their ability to enhance the osseointegrative properties. PEALD was chosen for film deposition to circumvent drawbacks present in line-of-sight deposition techniques, which require technically complex setups for a homogeneous coating thickness. Film conformality was analyzed on silicon 3D test structures and PEEK with micron-scale surface roughness. Wettability and surface energy were determined through contact angle measurements; film roughness and crystallinity were determined by atomic force microscopy and X-ray diffraction, respectively. Adhesion properties of TiO₂ on PEEK were determined with tensile strength tests. Cell tests were performed with the mouse mesenchymal tumor stem cell line ST-2. TiO₂-coated PEEK disks were used as substrates for cell proliferation tests and long-term differentiation tests. After 28 days of cultivation, a mineralized bone matrix was observed. Furthermore, the collagen I and osteocalcin content were determined. The results reveal that the osteogenic properties of the TiO₂ thin film are comparable to those of hydroxyapatite, and thus bioactive properties of PEEK implants are improved by TiO₂ thin films deposited with PEALD.

Surface Modified Techniques and Emerging Functional Coating of Dental Implants

Dental implants are widely used in the field of oral restoration, but there are still problems leading to implant failures in clinical application, such as failed osseointegration, marginal bone resorption, and peri-implantitis, which restrict the success rate of dental implants and patient satisfaction. Poor osseointegration and bacterial infection are the most essential reasons resulting in implant failure. To improve the clinical outcomes of implants, many scholars devoted to modifying the surface of implants, especially to preparing different physical and chemical modifications to improve the osseointegration between alveolar bone and implant surface. Besides, the bioactive-coatings to promote the adhesion and colonization of ossteointegration-related proteins and cells also aim to improve the osseointegration. Meanwhile, improving the anti-bacterial performance of the implant surface can obstruct the adhesion and activity of bacteria, avoiding the occurrence of inflammation related to implants. Therefore, this review comprehensively investigates and summarizes the modifying or coating methods of implant surfaces, and analyzes the ossteointegration ability and anti-bacterial characteristics of emerging functional coatings in published references.

Immobilization of surface non-affinitive protein onto a metal surface by an external electric field

We investigated an alternate technique to coat the surface with a protein having no surface affinity, without the use of any exotic chemical agents. An external electric field was utilized to prepare the protein coating on a metal substrate. Stainless steel (St) substrate and lysozyme (LSZ) were used as the surface to be coated and the model non-adsorptive protein, respectively. Dynamics of the adsorption of LSZ on the St surface in the presence and absence of an external electric potential (EEP) were monitored by in-situ ellipsometry. Applying negative surface potential (-0.4 V vs Ag/AgCl) forced the adsorption of LSZ onto the St surface where LSZ did not adsorb without applying any EEP. The repetition of the EEP-application and -cut-off indicated the controllability of the LSZ coating amount depending on the total duration of the EEP-application. The coated LSZ largely remained bound to the surface even by the cut-off of the external electric field, the ratio of which to the detached amount was roughly constant (approximately 7:3). Furthermore, the LSZ coated surface on the St substrate was found to be reversibly switched between being affinitive and non-affinitive to a typical model protein adsorbate (bovine serum albumin) by the EEP-application and cut-off.

Surface Characterization of Electro-Assisted Titanium Implants: A Multi-Technique Approach

The understanding of chemical-physical, morphological, and mechanical properties of polymer coatings is a crucial preliminary step for further biological evaluation of the processes occurring on the coatings' surface. Several studies have demonstrated how surface properties play a key role in the interactions between biomolecules (e.g., proteins, cells, extracellular matrix, and biological fluids) and titanium, such as chemical composition (investigated by means of XPS, TOF-SIMS, and ATR-FTIR), morphology (SEM-EDX), roughness (AFM), thickness (Ellipsometry), wettability (CA), solution-surface interactions (QCM-D), and mechanical features (hardness, elastic modulus, adhesion, and fatigue strength). In this review, we report an overview of the main analytical and mechanical methods commonly used to characterize polymer-based coatings deposited on titanium implants by electro-assisted techniques. A description of the relevance and shortcomings of each technique is described, in order to provide suitable information for the design and characterization of advanced coatings or for the optimization of the existing ones.

Micropatterned biofunctional lubricant-infused surfaces promote selective localized cell adhesion and patterning

Micropatterned biofunctional surfaces provide a wide range of applications in bioengineering. A key characteristic which is sought in these types of bio-interfaces is prevention of non-specific adhesion for enhanced biofunctionality and targeted binding. Lubricant-infused omniphobic coatings have exhibited superior performance in attenuating non-specific adhesion; however, these coatings completely block the surfaces and do not support targeted adhesion or patterning. In this work, we introduce a novel lubricant-infused surface with biofunctional micropatterned domains integrated within an omniphobic layer. This new class of micropatterned lubricant-infused surfaces simultaneously promotes localized and directed binding of desired targets, as well as repellency of undesired species, especially in human whole blood. Furthermore, this modification method is easily translatable to microfluidic devices offering a wider range of applications and improved performance for immunoassays in whole blood and inhibition of clot formation in microfluidic channels. The biofunctional micropatterned lubricant-infused surfaces were created through a bench-top straight forward process by integrating microcontact printing, chemical vapor deposition (CVD) of self-assembled monolayers (SAMs) of fluorosilanes, and further infusion of the SAMs with a bio-compatible fluorocarbon-based lubricant layer. The developed surfaces, patterned with anti-CD34 antibodies, yield enhanced adhesion and controlled localized binding of target biomolecules (e.g. antibodies) and CD34 positive cells (e.g. HUVECs) inside microfluidic devices, outperforming conventional blocking methods (e.g. bovine serum albumin (BSA) or poly(ethylene glycol) (PEG)) in buffer and human whole blood. These surfaces offer a straightforward and effective way to enhance blocking capabilities while preserving the biofunctionality of a micropatterned system in complex biological environments such as whole blood. We anticipate that these micropatterned biofunctional interfaces will find a wide range of applications in microfluidic devices and biosensors for enhanced and localized targeted binding while preventing non-specific adhesion.

Biomechanical behaviours of the bone-implant interface: a review

In recent decades, cementless implants have been widely used in clinical practice to replace missing organs, to replace damaged or missing bone tissue or to restore joint functionality. However, there remain risks of failure which may have dramatic consequences. The success of an implant depends on its stability, which is determined by the biomechanical properties of the bone-implant interface (BII). The aim of this review article is to provide more insight on the current state of the art concerning the evolution of the biomechanical properties of the BII as a function of the implant's environment. The main characteristics of the BII and the determinants of implant stability are first introduced. Then, the different mechanical methods that have been employed to derive the macroscopic properties of the BII will be described. The experimental multi-modality approaches used to determine the microscopic biomechanical properties of periprosthetic newly formed bone tissue are also reviewed. Eventually, the influence of the implant's properties, in terms of both surface properties and biomaterials, is investigated. A better understanding of the phenomena occurring at the BII will lead to (i) medical devices that help surgeons to determine an implant's stability and (ii) an improvement in the quality of implants.

Microfluidic Shear Assay to Distinguish between Bacterial Adhesion and Attachment Strength on Stiffness-Tunable Silicone Substrates

Tuning surface composition and stiffness is now an established strategy to improve the integration of medical implants. Recent evidence suggests that matrix stiffness affects bacterial adhesion, but contradictory findings have been reported in the literature. Distinguishing between the effects of bacterial adhesion and attachment strength on these surfaces may help interpret these findings. Here, we develop a precision microfluidic shear assay to quantify bacterial adhesion strength on stiffness-tunable and biomolecule-coated silicone materials. We demonstrate that bacteria are more strongly attached to soft silicones, compared to stiff silicones; as determined by retention against increasing shear flows. Interestingly, this effect is reduced when the surface is coated with matrix biomolecules. These results demonstrate that bacteria do sense and respond to stiffness of the surrounding environment and that precisely defined assays are needed to understand the interplay among surface mechanics, composition, and bacterial binding.

Interaction of biologically relevant ions and organic molecules with titanium oxide (rutile) surfaces: A review on molecular dynamics studies

The surface of a biomaterial can play a major role in its biological fate since the surface is the primary pathway for its interaction with the body. As the natural response of the body to a foreign material is to encapsulate it with a fibrous material, the interactions between the body and the biomaterial are mediated by this fibrous layer. Initial interactions occur between the biomaterial surface, water, ionic species and organic molecules, which then mediate further interactions with body tissues. Surface engineering can influence these interactions and hence, improve the biocompatibility of the biomaterial. Therefore, both experimental and computational studies have been interested in phenomena happening at the solid-solution interface as their mechanisms and driving forces can point to new directions for biomaterial design and evaluation. In this review, we summarize the computational work on the interaction of titanium oxide surfaces (mainly rutile) with solvated ions and organic molecules by means of molecular dynamics, with a certain relevance to bioactivity testing protocols. The primary goal of this review is to present the current state of the art and draw attention to points where further investigations are required.

Enhanced biocompatibility and osseointegration of calcium titanate coating on titanium screws in rabbit femur

This study aimed to examine the biocompatibility of calcium titanate (CaTiO₃) coating prepared by a simplified technique in an attempt to assess the potential of CaTiO₃ coating as an alternative to current implant coating materials. CaTiO₃-coated titanium screws were implanted with hydroxyapatite (HA)-coated or uncoated titanium screws into medial and lateral femoral condyles of 48 New Zealand white rabbits. Imaging, histomorphometric and biomechanical analyses were employed to evaluate the osseointegration and biocompatibility 12 weeks after the implantation. Histology and scanning electron microscopy revealed that bone tissues surrounding the screws coated with CaTiO₃ were fully regenerated and they were also well integrated with the screws. An interfacial fibrous membrane layer, which was found in the HA coating group, was not noticeable between the bone tissues and CaTiO₃-coated screws. X-ray imaging analysis showed in the CaTiO₃ coating group, there was a dense and tight binding between implants and the bone tissues; no radiation translucent zone was found surrounding the implants as well as no detachment of the coating and femoral condyle fracture. In contrast, uncoated screws exhibited a fibrous membrane layer, as evidenced by the detection of a radiation translucent zone between the implants and the bone tissues. Additionally, biomechanical testing revealed that the binding strength of CaTiO₃ coating with bone tissues was significantly higher than that of uncoated titanium screws, and was comparable to that of HA coating. The study demonstrated that CaTiO₃ coating in situ to titanium screws possesses great biocompatibility and osseointegration comparable to HA coating.

Current approaches for modulation of the nanoscale interface in the regulation of cell behavior

Regulation of cell behavior in response to nanoscale features has been the focus of much research in recent years and the successful generation of nanoscale features capable of mimicking the natural nanoscale interface has been of great interest in the field of biomaterials research. In this review, we discuss relevant nanofabrication techniques and how they are combined with bioengineering applications to mimic the natural extracellular matrix (ECM) and create valuable nanoscale interfaces.

Understanding the cochlear implant environment by mapping perilymph proteomes from different species

Cochlear implants operate within a bony channel of the cochlea, bathed in a fluid known as the perilymph. The perilymph is a complex fluid containing ions and proteins, which are known to actively interact with metallic electrodes. To improve our understanding of how cochlear implant performance varies in preclinical in vivo studies in comparison to human trials and patient outcomes, the protein composition (or perilymph proteome) is needed. Samples of perilymph were gathered from feline and guinea pig subjects and analyzed using liquid chromatography with tandem mass spectrometry (LC-MS/MS) to produce proteomes and compare against the recently published human proteome. Over 64% of the proteins in the guinea pig proteome were found to be common to the human proteome. The proportions of apolipoproteins, enzymes and immunoglobulins showed little variation between the two proteomes, with other classes showing similarity. This establishes a good basis for comparison of results. The results for the feline profile showed less similarity with the human proteome and would not provide a quality comparison. This work highlights the suitability of the guinea pig to model the biological environment of the human cochlear and the need to carefully select models of the biological environment of a cochlear implant to more adequately translate in vitro and in vivo studies to the clinic.

Graphene oxide nanolayers as nanoparticle anchors on biomaterial surfaces with nanostructures and charge balance for bone regeneration

Graphene oxide (GO) is a carbon-based nanomaterial with high surface area and abundant functional groups, providing various sites for binding and immobilization of growth factor vehicles. This study used GO nanolayer as an anchor for the immobilization of bone morphogenetic protein-2 (BMP-2)-encapsulated bovine serum albumin nanoparticles (NPs) on the hydroxyapatite (HA) and tricalcium phosphate (TCP) scaffolds by electrostatic interaction between the positive charges of the NPs and negative charges of GO. GO nanolayers prevented the rapid degradation of TCP scaffolds. Moreover, GO nanolayers promoted NP adsorption on these scaffolds, and realized BMP-2 sustained release. NPs endowed the scaffold surfaces with a nanostructure similar to that of the extracellular matrix (ECM), improving bone marrow stromal cell (BMSC) attachment. Furthermore, the positive charged NPs and negative charged GO nanolayers constructed a charge-balanced surface on the scaffolds, enhancing BMSC proliferation. The nanostructure, charge balance and BMP-2 sustained release capability synergistically improved BMSC differentiation and bone regeneration. In summary, GO is a potential candidate to modify biomaterial surfaces as an anchor for efficient immobilization of growth factor vehicles. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 105A: 1311-1323, 2017.

The bone-implant interface of dental implants in humans on the atomic scale

Osseointegration of dental implants occurs on a hierarchy of length scales down to the atomic level. A deeper understanding of the complex processes that take place at the surface of an implant on the smallest scale is of interest for the development of improved biomaterials. To date, transmission electron microscopy (TEM) has been utilized for examination of the bone-implant interface, providing details on the nanometer level. In this study we show that TEM imaging can be complemented with atom probe tomography (APT) to reveal the chemical composition of a Ti-based dental implant in a human jaw on the atomic level of resolution. As the atom probe technique has equal sensitivity for all elements, it allows for 3 dimensional characterizations of osseointegrated interfaces with unprecedented resolution. The APT reconstructions reveal a Ca-enriched zone in the immediate vicinity of the implant surface. A surface oxide of some 5nm thickness was measured on the titanium implant, with a sub-stoichiometric composition with respect to TiO₂. Minor incorporation of Ca into the thin oxide film was also evident. We conclude that the APT technique is capable of revealing chemical information from the bone-implant interface in 3D with unprecedented resolution, thus providing important insights into the mechanisms behind osseointegration.

STATEMENT OF SIGNIFICANCE

Osseointegration of dental implants occurs on a hierarchy of length scales down to the atomic level. A deeper understanding of the complex processes that take place at the surface of an implant on the smallest scale is of interest for the development of improved biomaterials. To date, transmission electron microscopy (TEM) has been utilized for examination of the bone-implant interface, providing details on the nanometer level. In this study we show that TEM imaging can be complemented with atom probe tomography (APT) to reveal the chemical composition of a Ti-based dental implant in a human jaw on the atomic level of resolution. Correlative microscopy ensures the accuracy of APT reconstructions and helps provide both chemical and structural information of the bone-implant interface on the smallest of length scales.

Characterization of protein adsorption on stretched polyurethane nanofibers prepared by electrospinning

Proteins adsorbed on thick nanofibers (diameter = 950 nm) showed decreased activity due to large conformational changes, whereas those adsorbed on thin nanofibers (diameter = 480 nm) retained a close-to-natural shape and thus showed relatively high activity.

Neurobiochemical changes in the vicinity of a nanostructured neural implant

Neural interface technologies including recording and stimulation electrodes are currently in the early phase of clinical trials aiming to help patients with spinal cord injuries, degenerative disorders, strokes interrupting descending motor pathways, or limb amputations. Their lifetime is of key importance; however, it is limited by the foreign body response of the tissue causing the loss of neurons and a reactive astrogliosis around the implant surface. Improving the biocompatibility of implant surfaces, especially promoting neuronal attachment and regeneration is therefore essential. In our work, bioactive properties of implanted black polySi nanostructured surfaces (520–800 nm long nanopillars with a diameter of 150–200 nm) were investigated and compared to microstructured Si surfaces in eight-week-long in vivo experiments. Glial encapsulation and local neuronal cell loss were characterised using GFAP and NeuN immunostaining respectively, followed by systematic image analysis. Regarding the severity of gliosis, no significant difference was observed in the vicinity of the different implant surfaces, however, the number of surviving neurons close to the nanostructured surface was higher than that of the microstructured ones. Our results imply that the functionality of implanted microelectrodes covered by Si nanopillars may lead to improved long-term recordings.

Raloxifene Covalently Bonded to Titanium Implants by Interfacing with (3-Aminopropyl)-Triethoxysilane Affects Osteoblast-like Cell Gene Expression

Since Raloxifene, a drug used in osteoporosis therapy, inhibits the osteoclast functions but not osteoblast functions, it could improve the recovery during implant surgery. This preliminary report describes a simple method to link, through a covalent bond, Raloxifene to titanium by interfacing with (3-aminopropyl)-Triethoxysilane as assessed by the IR-FT and SEM. To evaluate the biological response of osteoblast-like cells to this implant, we compared expression gene profiling of cell cultures on Raloxifene conjugated implant and normal implant by DNA microarray. By using DNA microarrays containing 19,200 genes, we identified differently expressed genes in osteoblast-like cell line (MG-63). Surface Raloxifene conjugated implants have been shown to have a relevant importance in modifying cell response. This result could be an interesting starting point for the use of an immediate functional loading of implants.

The use of a proteinaceous "cushion" with a polystyrene-binding peptide tag to control the orientation and function of a target peptide adsorbed to a hydrophilic polystyrene surface

In immobilizing target biomolecules on a solid surface, it is essential (i) to orient the target moiety in a preferred direction and (ii) to avoid unwanted interactions of the target moiety including with the solid surface. The preferred orientation of the target moiety can be achieved by genetic conjugation of an affinity peptide tag specific to the immobilization surface. Herein, we report on a strategy for reducing the extent of direct interaction between the target moiety and surface in the immobilization of hexahistidine peptide (6His) and green fluorescent protein (GFP) on a hydrophilic polystyrene (PS) surface: Ribonuclease HII from Thermococcus kodakaraensis (cHII) was genetically inserted as a "cushion" between the PS-affinity peptide tag and target moiety. The insertion of a cushion protein resulted in a considerably stronger immobilization of target biomolecules compared to conjugation with only a PS affinity peptide tag, resulting in a substantially enhanced accessibility of the detection antibody to the target 6His peptide. The fluorescent intensity of the GFP moiety was decreased by approximately 30% as the result of fusion with cHII and the PS-affinity peptide tag but was fully retained in the immobilization on the PS surface irrespective of the increased binding force. Furthermore, the fusion of cHII did not impair the stability of the target GFP moiety. Accordingly, the use of a proteinaceous cushion appears to be promising for the immobilization of functional biomolecules on a solid surface. © 2016 American Institute of Chemical Engineers Biotechnol. Prog., 32:527-534, 2016.

Functionalized mesoporous bioactive glass scaffolds for enhanced bone tissue regeneration

Mesoporous bioactive glass (MBG), which possesses excellent bioactivity, biocompatibility and osteoconductivity, has played an important role in bone tissue regeneration. However, it is difficult to prepare MBG scaffolds with high compressive strength for applications in bone regeneration; this difficulty has greatly hindered its development and use. To solve this problem, a simple powder processing technique has been successfully developed to fabricate a novel type of MBG scaffold (MBGS). Furthermore, amino or carboxylic groups could be successfully grafted onto MBGSs (denoted as N-MBGS and C-MBGS, respectively) through a post-grafting process. It was revealed that both MBGS and the functionalized MBGSs could significantly promote the proliferation and osteogenic differentiation of bMSCs. Due to its positively charged surface, N-MBGS presented the highest in vitro osteogenic capability of the three samples. Moreover, in vivo testing results demonstrated that N-MBGS could promote higher levels of bone regeneration compared with MBGS and C-MBGS. In addition to its surface characteristics, it is believed that the decreased degradation rate of N-MBGS plays a vital role in promoting bone regeneration. These findings indicate that MBGSs are promising materials with potential practical applications in bone regeneration, which can be successfully fabricated by combining a powder processing technique and post-grafting process.

An exploration of plastic deformation dependence of cell viability and adhesion in metallic implant materials

The relationship between cell viability and adhesion behavior, and micro-deformation mechanisms was investigated on austenitic 316L stainless steel samples, which were subjected to different amounts of plastic strains (5%, 15%, 25%, 35% and 60%) to promote a variety in the slip and twin activities in the microstructure. Confocal laser scanning microscopy (CLSM) and field emission scanning electron microscopy (FESEM) revealed that cells most favored the samples with the largest plastic deformation, such that they spread more and formed significant filopodial extensions. Specifically, brain tumor cells seeded on the 35% deformed samples exhibited the best adhesion performance, where a significant slip activity was prevalent, accompanied by considerable slip-twin interactions. Furthermore, maximum viability was exhibited by the cells seeded on the 60% deformed samples, which were particularly designed in a specific geometry that could endure greater strain values. Overall, the current findings open a new venue for the production of metallic implants with enhanced biocompatibility, such that the adhesion and viability of the cells surrounding an implant can be optimized by tailoring the surface relief of the material, which is dictated by the micro-deformation mechanism activities facilitated by plastic deformation imposed by machining.