Sustainable biosurfactant produced by Serratia marcescens UCP 1549 and its suitability for agricultural and marine bioremediation applications

Cellulosimicrobium sp. Strain L1: A Study on the Optimization of the Conditions and Performance of a Combined Biological Trickling Filter for Hydrogen Sulfide Degradation

Sulfide is a toxic and hazardous substance in the agricultural environment, which can cause damage to humans and livestock when exposed to large amounts of air. In this study, we performed one-factor optimization of the culture conditions and culture fractions of the Cellulosimicrobium sp. strain L1 and combined it with a biological trickling filter cell for the degradation of hydrogen sulfide for 24 consecutive days. The degradation effect of strain L1 and the biological trickling filter (BTF) on hydrogen sulfide was investigated, and the changes in intermediate products in the degradation process were briefly analyzed. The results showed that strain L1 had the highest conversion efficiency when incubated with 3 g/L sucrose as the carbon source and 1 g/L NH4Cl as the nitrogen source at a temperature of 35 °C, an initial pH of 5, and a NaCl concentration of 1%. The concentration of thiosulfate increased and then decreased during the degradation process, and the concentration of sulfate increased continuously. When strain L1 was applied to the biological trickling filter, it could degrade 359.53 mg/m3 of H2S. This study provides a deeper understanding of sulfide degradation in biological trickling filters and helps promote the development of desulfurization technology and the treatment of malodorous gasses produced by the accumulation of large quantities of livestock manure.

Biotechnological Utilization of Agro-Industrial Residues and By-Products-Sustainable Production of Biosurfactants

The importance and interest in the efficient use and valorization of agro-industrial residues and by-products have grown due to environmental problems associated with improper disposal. Biotechnological production processes, including microbial biosurfactant production, represent a sustainable way to utilize agro-industrial residues and by-products, which are applied as substrates in these processes. Biosurfactants produced by microorganisms using renewable resources are a viable alternative to traditional petrochemical surfactants and have several potential uses in a wide range of industrial sectors due to their minimal ecotoxicity, easy biodegradability, and moderate production conditions. The common applications of biosurfactants, besides in food industry as food additives and preservatives, are in agriculture, environmental protection, the cosmetics and pharmaceutical industry, wastewater treatment, the petroleum industry, etc. This review aims to summarize the comprehensive scientific research related to the use of various agro-industrial residues and by-products in the microbial production of biosurfactants, as well as to emphasize the present state and the importance of their sustainable production. Additionally, based on the available biosurfactant market analysis datasets and research studies, the current situation in science and industry and the future perspectives of microbial biosurfactant production have been discussed.

Isolation and characterization of a cold-active, detergent-stable protease from Serratia sp. TGS1

Psychrophiles are cold-adapted microorganisms living in cold regions and are known to generate cold-active enzymes such as proteases, lipases, and peptidases. These types of enzymes are a major part of the market of the food and textile sector. This study aimed to isolate and characterize the cold-active and detergent-stable, extracellular protease from psychotrophic bacteria Serratia sp. TGS1 (OQ654005). Protease was purified by gel permeation chromatography using Sephadex G-75. The specific activity of the purified protease was 250 U/mg at 15°C, with a purification fold of 5.68 and a percentage yield of 60%. The cold active protease was stable within a temperature range of 5-30°C and a pH range of 6-10. Ca+2 and Mg+2 enhanced its activity while chelators like ethylenediaminetetraacetic acid inhibited cold active protease, showing it as metalloprotease in nature. The enzyme was sensitive to Cu+2 , Zn+2 , and Hg+2 , and the proteolytic activity decreased upon treatment with heavy metals. The molecular weight of the protease was estimated to be 47 kDa using sodium dodecyl sulfate (SDS)-polyacrylamide gel electrophoresis. Proteins within a specific range of molecular weight possess desirable properties for industrial enzyme use. By working on a specific range, the researchers intended to examine an enzyme to examine its specific characteristics. The purified protease showed high stability to detergents like SDS, Tween 20, Tween 60, and Triton X. The maximum velocity Vmax and Km values were 59.90 mg/min/mL and 1.53 mg/mL, respectively. The obtained protease exhibited an interesting activity at a broad range of pH (6-10) and stability at low temperatures (5-30°C) and detergents. Such enzymatic features of versatile and potent cold-active enzymes enhance their industrial applications to meet food, dairy, and laundry requirements.

Importance of microbial amphiphiles: interaction potential of biosurfactants, amyloids, and other exo-polymeric-substances

Microorganisms produce a diverse group of biomolecules having amphipathic nature (amphiphiles). Microbial amphiphiles, including amyloids, bio-surfactants, and other exo-polymeric substances, play a crucial role in various biological processes and have gained significant attention recently. Although diverse in biochemical composition, these amphiphiles have been reported for common microbial traits like biofilm formation and pathogenicity due to their ability to act as surface active agents with active interfacial properties essential for microbes to grow in various niches. This enables microbes to reduce surface tension, emulsification, dispersion, and attachment at the interface. In this report, the ecological importance and biotechnological usage of important amphiphiles have been discussed. The low molecular weight amphiphiles like biosurfactants, siderophores, and peptides showing helical and antimicrobial activities have been extensively reported for their ability to work as quorum-sensing mediators. While high molecular weight amphiphiles make up amyloid fibers, exopolysaccharides, liposomes, or magnetosomes have been shown to have a significant influence in deciding microbial physiology and survival. In this report, we have discussed the functional similarities and biochemical variations of several amphipathic biomolecules produced by microbes, and the present report shows these amphiphiles showing polyphyletic and ecophysiological groups of microorganisms and hence can `be replaced in biotechnological applications depending on the compatibility of the processes.

Characterization of pumilacidin, a lipopeptide biosurfactant produced from Bacillus pumilus NITDID1 and its prospect in bioremediation of hazardous pollutants

Highly hydrophobic compounds like petroleum and their byproducts, once released into the environment, can persist indefinitely by virtue of their ability to resist microbial degradation, ultimately paving the path to severe environmental pollution. Likewise, the accumulation of toxic heavy metals like lead, cadmium, chromium, etc., in the surroundings poses an alarming threat to various living organisms. To remediate the matter in question, the applicability of a biosurfactant produced from the mangrove bacterium Bacillus pumilus NITDID1 (Accession No. KY678446.1) is reported here. The structural characterization of the produced biosurfactant revealed it to be a lipopeptide and has been identified as pumilacidin through FTIR, NMR, and MALDI-TOF MS. The critical micelle concentration of pumilacidin was 120 mg/L, and it showed a wide range of stability in surface tension reduction experiments under various environmental conditions and exhibited a high emulsification index of as much as 90%. In a simulated setup of engine oil-contaminated sand, considerable oil recovery (39.78%) by this biosurfactant was observed, and upon being added to a microbial consortium, there was an appreciable enhancement in the degradation of the used engine oil. As far as the heavy metal removal potential of biosurfactant is concerned, as much as 100% and 82% removal was observed for lead and cadmium, respectively. Thus, in a nutshell, the pumilacidin produced from Bacillus pumilus NITDID1 holds promise for multifaceted applications in the field of environmental remediation.

Structural Diversity of the Lipopeptide Biosurfactant Produced by a Newly Isolated Strain, Geobacillus thermodenitrifcans ME63

The genus Geobacillus is active in degradation of hydrocarbons in thermophilic and facultative environments since it was first reported in 1920. Here, we report a new strain, Geobacillus thermodenitrificans ME63, isolated from an oilfield with the ability of producing the biosurfactant. The composition, chemical structure, and surface activity of the biosurfactant produced by G. thermodenitrificans ME63 were investigated by using a combination of the high-performance liquid chromatography, time-of-flight ion mass spectrometry, and surface tensiometer. The biosurfactant produced by strain ME63 was identified as surfactin with six variants, which is one of the representative family of lipopeptide biosurfactants. The amino acid residue sequence in the peptide of this surfactin is N-Glu → Leu → Leu → Val → Leu → Asp → Leu-C. The critical micelle concentration (CMC) of the surfactin is 55 mg L^-1, and the surface tension at CMC is 35.9 mN m^-1, which is promising in bioremediation and oil recovery industries. The surface activity and emulsification properties of biosurfactants produced by G. thermodenitrificans ME63 showed excellent resistance to temperature changes, salinity changes, and pH changes.

Production and Characterization of New Biosurfactants/Bioemulsifiers from Pantoea alhagi and Their Antioxidant, Antimicrobial and Anti-Biofilm Potentiality Evaluations

The present work aimed to develop rapid approach monitoring using a simple selective method based on a positive hemolysis test, oil spreading activity and emulsification index determinations. It is the first to describe production of biosurfactants (BS) by the endophytic Pantoea alhagi species. Results indicated that the new BS evidenced an E24 emulsification index of 82%. Fourier-transform infrared (FTIR) results mentioned that the described BS belong to the glycolipid family. Fatty acid profiles showed the predominance of methyl 2-hyroxydodecanoate in the cell membrane (67.00%) and methyl 14-methylhexadecanoate (12.05%). The major fatty acid in the BS was oleic acid (76.26%), followed by methyl 12-methyltetradecanoate (10.93%). Markedly, the BS produced by the Pantoea alhagi species exhibited antimicrobial and anti-biofilm activities against tested human pathogens. With superior antibacterial activity against Escherchia coli and Staphylococcus aureus, a high antifungal effect was given against Fusarium sp. with a diameter of zone of inhibition of 29.5 mm, 36 mm and 31 mm, obtained by BS dissolved in methanol extract. The DPPH assay indicated that the BS (2 mg/mL) showed a higher antioxidant activity (78.07 inhibition percentage). The new BS exhibited specific characteristics, encouraging their use in various industrial applications.

Bacterial-derived surfactants: an update on general aspects and forthcoming applications

The search for sustainable alternatives to the production of chemicals using renewable substrates and natural processes has been widely encouraged. Microbial surfactants or biosurfactants are surface-active compounds synthesized by fungi, yeasts, and bacteria. Due to their great metabolic versatility, bacteria are the most traditional and well-known microbial surfactant producers, being Bacillus and Pseudomonas species their typical representatives. To be successfully applied in industry, surfactants need to maintain stability under the harsh environmental conditions present in manufacturing processes; thus, the prospection of biosurfactants derived from extremophiles is a promising strategy to the discovery of novel and useful molecules. Bacterial surfactants show interesting properties suitable for a range of applications in the oil industry, food, agriculture, pharmaceuticals, cosmetics, bioremediation, and more recently, nanotechnology. In addition, they can be synthesized using renewable resources as substrates, contributing to the circular economy and sustainability. The article presents a general and updated review of bacterial-derived biosurfactants, focusing on the potential of some groups that are still underexploited, as well as, recent trends and contributions of these versatile biomolecules to circular bioeconomy and nanotechnology.

A comprehensive study on microbial-surfactants from bioproduction scale-up toward electrokinetics remediation of environmental pollutants: Challenges and perspectives

Currently, researchers have focused on electrokinetic (EK) bioremediation due to its potential to remove a wide-range of pollutants. Further, to improve their performance, synthetic surfactants are employed as effective additives because of their excellent solubility and mobility. Synthetic surfactants have an excessive position in industries since they are well-established, cheap, and easily available. Nevertheless, these surfactants have adverse environmental effects and could be detrimental to aquatic and terrestrial life. Owing to social and environmental awareness, there is a rising demand for bio-based surfactants in the global market, from environmental sustainability to public health, because of their excellent surface and interfacial activity, higher and stable emulsifying property, biodegradability, non- or low toxicity, better selectivity and specificity at extreme environmental conditions. Unfortunately, challenges to biosurfactants, like expensive raw materials, low yields, and purification processes, hinder their applicability to large-scale. To date, extensive research has already been conducted for production scale-up using multidisciplinary approaches. However, it is still essential to research and develop high-yielding bacteria for bioproduction through traditional and biotechnological advances to reduce production costs. Herein, this review evaluates the recent progress made on microbial-surfactants for bioproduction scale-up and provides detailed information on traditional and advanced genetic engineering approaches for cost-effective bioproduction. Furthermore, this study emphasized the role of electrokinetic (EK) bioremediation and discussed the application of BioS-mediated EK for various pollutants remediation.

Development of a microbial protease for composting swine carcasses, optimization of its production and elucidation of its catalytic hydrolysis mechanism

BACKGROUND

Dead swine carcass composting is an excellent method for harmless treatment and resource utilization of swine carcass. However, poor biodegradation ability of traditional composting results in poor harmless treatment effect. Researches report that the biodegradation ability of composting can be improved by inoculation with enzyme-producing microorganisms or by inoculation with enzyme preparations. At present, the researches on improving the efficiency of dead swine carcass composting by inoculating enzyme-producing microorganisms have been reported. However, no work has been reported on the development of enzyme preparations for dead swine carcass composting.

METHODOLOGY

The protease-producing strain was isolated by casein medium, and was identified by 16 S rRNA gene sequencing. The optimal fermentation conditions for maximum protease production were gradually optimized by single factor test. The extracellular protease was purified by ammonium sulfate precipitation and Sephadex G-75 gel exclusion chromatography. The potential for composting applications of the purified protease was evaluated by characterization of its biochemical properties. And based on amino acid sequence analysis, molecular docking and inhibition test, the catalytic hydrolysis mechanism of the purified protease was elucidated.

RESULTS

In this study, a microbial protease was developed for swine carcass composting. A protease-producing strain DB1 was isolated from swine carcass compositing and identified as Serratia marcescen. Optimum fermentation conditions for maximum protease production were 5 g/L glucose, 5 g/L urea, 1.5 mmol/L Mg²⁺, initial pH-value 8, inoculation amount 5%, incubation temperature 30 °C and 60 h of fermentation time. The specific activity of purified protease reached 1982.77 U/mg, and molecular weight of the purified protease was 110 kDa. Optimum pH and temperature of the purified protease were 8 and 50 °C, respectively, and it had good stability at high temperature and in alkaline environments. The purified protease was a Ser/Glu/Asp triad serine protease which catalyzed substrate hydrolysis by Glu, Arg, Ser, Asp and Tyr active residues.

CONCLUSIONS

In general, the microbial protease developed in this study was suitable for industrial production and has the potential to enhance composting at thermophilic stage. Moreover, the catalytic hydrolysis mechanism of the protease was further analyzed in this study.

Biomolecules from Serratia sp. CS1 indigenous to Ethiopian natural alkaline lakes: biosurfactant characteristics and assessment of compatibility in a laundry detergent

In this study, the biosurfactants (Bio-SFs) producing bacteria are screened from the selected alkaline lake of Ethiopia, and the potential bacterial strain and their produced Bio-SFs are further characterized. In an initial screening, 25 bacterial isolates were isolated, and among those, the bacterial isolate assigned as CS1 was identified as the most potent producer of Bio-SFs using a subsequent characterization process. The CS1 strain was identified as Serratia sp. via biochemical and molecular methods. An emulsion index (E₂₄) of 69.06 ± 0.11% was obtained for CS1 after 5 days of incubation time at 30 °C. The CS1-extracted Bio-SFs were characterized by Fourier transform infrared (FTIR), and it indicated that the type of biosurfactant produced was a glycolipid. The stability of the crude Bio-SFs was characterized, and the optimal conditions were found to be 80 °C, pH 8, and 3% NaCl, respectively. The extracted Bio-SFs were compatible with tested commercial detergents, and its efficiency increased from 12.2 ± 0.1% to 67.1 ± 0.17% and 70.43 ± 0.11% when combined with commercially available detergent brands in Ethiopia such as Taza and Largo, respectively. This study suggests that the isolated S. marcescens CS1 strain has the potential to produce Bio-SFs that are viable competence to replace the use of synthetic chemicals in the production of commercial detergents.

A review of the role of biosurfactants in the biodegradation of hydrophobic organopollutants: production, mode of action, biosynthesis and applications

The increasing influence of human activity and industrialization has adversely impacted the environment via pollution with organic contaminants, which are minimally soluble in water. These hydrophobic organopollutants may be present in sediment, water or biota and have created concern due to their toxic effects in mammals. The ability of microorganisms to degrade pollutants makes their use the most effective, inexpensive and ecofriendly method for environmental remediation. Microorganisms have the ability to produce natural surfactants (biosurfactants) that increase the bioavailability of hydrophobic organopollutants, which enables their use as carbon and energy sources. Due to microbial diversity in production, and the biodegradability, nontoxicity, stability and specific activity of the surfactants, the use of microbial surfactants has the potential to overcome problems associated with contamination by hydrophobic organopollutants.This review provides an overview of the current state of knowledge regarding microbial surfactant production, mode of action in the biodegradation of hydrophobic organopollutants and biosynthetic pathways as well as their applications using emergent strategy tools to remove organopollutants from the environment. It is also specified for the first time that biosurfactants are produced either as growth-associated products or secondary metabolites, and are produced in different amounts by a wide range of microorganisms.

A review on biosurfactant producing bacteria for remediation of petroleum contaminated soils

The discharge of potentially toxic petroleum hydrocarbons into the environment has been a matter of concern, as these organic pollutants accumulate in many ecosystems due to their hydrophobicity and low bioavailability. Petroleum hydrocarbons are neurotoxic and carcinogenic organic pollutants, extremely harmful to human and environmental health. Traditional treatment methods for removing hydrocarbons from polluted areas, including various mechanical and chemical strategies, are ineffective and costly. However, many indigenous microorganisms in soil and water can utilise hydrocarbon compounds as sources of carbon and energy and hence, can be employed to degrade hydrocarbon contaminants. Therefore, bioremediation using bacteria that degrade petroleum hydrocarbons is commonly viewed as an environmentally acceptable and effective method. The efficacy of bioremediation can be boosted further by using potential biosurfactant-producing microorganisms, as biosurfactants reduce surface tension, promote emulsification and micelle formation, making hydrocarbons bio-available for microbial breakdown. Further, introducing nanoparticles can improve the solubility of hydrophobic hydrocarbons as well as microbial synthesis of biosurfactants, hence establishing a favourable environment for microbial breakdown of these chemicals. The review provides insights into the role of microbes in the bioremediation of soils contaminated with petroleum hydrocarbons and emphasises the significance of biosurfactants and potential biosurfactant-producing bacteria. The review partly focusses on how nanotechnology is being employed in different critical bioremediation processes.

Microbial surfactants: A journey from fundamentals to recent advances

Microbial surfactants are amphiphilic surface-active substances aid to reduce surface and interfacial tensions by accumulating between two fluid phases. They can be generically classified as low or high molecular weight biosurfactants based on their molecular weight, whilst overall chemical makeup determines whether they are neutral or anionic molecules. They demonstrate a variety of fundamental characteristics, including the lowering of surface tension, emulsification, adsorption, micelle formation, etc. Microbial genera like Bacillus spp., Pseudomonas spp., Candida spp., and Pseudozyma spp. are studied extensively for their production. The type of biosurfactant produced is reliant on the substrate utilized and the pathway pursued by the generating microorganisms. Some advantages of biosurfactants over synthetic surfactants comprise biodegradability, low toxicity, bioavailability, specificity of action, structural diversity, and effectiveness in harsh environments. Biosurfactants are physiologically crucial molecules for producing microorganisms which help the cells to grasp substrates in adverse conditions and also have antimicrobial, anti-adhesive, and antioxidant properties. Biosurfactants are in high demand as a potential product in industries like petroleum, cosmetics, detergents, agriculture, medicine, and food due to their beneficial properties. Biosurfactants are the significant natural biodegradable substances employed to replace the chemical surfactants on a global scale in order to make a cleaner and more sustainable environment.

Novel production of biodispersant by Serratia marcescens UCP 1549 in solid-state fermentation and application for oil spill bioremediation

Oil spills in aquatic ecosystems cause irreparable damage to marine life and the coastal populations of affected areas. In recent years, chemical dispersants have been extensively used to remedy these impacted ecosystems, although these agents have been increasingly restricted due to their toxic potential. In this context, biosurfactants are emerging as a promising alternative to chemical dispersants, which have some advantages including low toxicity, high biodegradability and good ecological acceptability. Thus, this study aimed to the production of biosurfactant by the bacteria Serratia marcescens UCP 1549 for application as biodispersant. The experiment was carried out using wheat bran as substrate in solid-state fermentation (SSF) as low-cost technology. Biosurfactant production was verified by the reduction of surface tension (28.4 mN/m) and interfacial tension (4.1 mN/m) with n-hexadecane. Also, promising result of emulsification (94%) with burned motor oil was obtained. Acid precipitation yielded 52.0 g/kg dry substrate of biosurfactant, that was identified as an anionic compound of a lipopeptide nature by the Zeta potential and FTIR spectrum, respectively. The biomolecule showed stability under extreme conditions of temperature, pH and salinity, as well as low toxicity against the microcrustacean Artemia salina. In addition, the biosurfactant demonstrated excellent properties to dispersing burned motor oil in water (ODA = 50.24 cm²) and to washing of marine stones (100% removal of burned motor oil). Therefore, these results confirm SSF as a sustainable technology for the production of biodispersant by S. marcescens UCP 1549, promising in the bioremediation of marine ecosystems impacted by petroderivatives.

Valorization of frying oil waste for biodetergent production using Serratia marcescens N2 and gamma irradiation assisted biorecovery

BACKGROUND

The complexity, toxicity and abundance of frying oil waste (FOW) render it difficult to be degraded biologically. The aim of the present work was to valorize FOW and investigate the potential use of the produced biosurfactant by Serratia marcescens N2 (Whole Genome sequencing accession ID SPSG00000000) as a biodetergent.

RESULTS

Serratia marcescens N2 demonstrated efficient valorization of FOW, using 1% peptone, 20% FOW and 8% inoculum size. Gene annotation showed the presence of serrawettin synthetase indicating that the produced biosurfactant was serrawettin. Zeta potential and Fourier Transform Infrared (FTIR) spectroscopy indicate that the biosurfactant produced was a negatively charged lipopeptide. The biosurfactant reduced the surface tension of water from 72 to 25.7 mN/m; its emulsification index was 90%. The valorization started after 1 h of incubation and reached a maximum of 83.3%. Gamma radiation was used to increase the biosurfactant yield from 9.4 to 19.2 g/L for non-irradiated and 1000 Gy irradiated cultures, respectively. It was noted that the biorecovery took place immediately as opposed to overnight storage required in conventional biosurfactant recovery. Both chemical and functional characteristics of the radiation induced biosurfactant did not change at low doses. The produced biosurfactant was used to wash oil stain; the highest detergency reached was 87% at 60 °C under stirring conditions for 500 Gy gamma assisted biorecovery. Skin irritation tests performed on experimental mice showed no inflammation.

CONCLUSION

This study was able to obtain a skin friendly effective biodetergent from low worth FOW using Serratia marcescens N2 with 83% efficient valorization using only peptone in the growth media unlike previous studies using complex media. Gamma radiation was for the first time experimented to assist biosurfactant recovery and doubling the yield without affecting the efficiency.

Fatal Bronchopneumonia and Tracheitis in a Green Turtle (Chelonia mydas) Caused by Serratia proteamaculans

A free-ranging subadult, male green turtle (Chelonia mydas) presented with radiographic evidence of pneumonia and died acutely. On necropsy, the trachea and bronchi were plugged by diphtheritic membranes, comprised of fibrin, necrotic debris, and colonies of bacilli, identified as Serratia proteamaculans. S. proteamaculans, typically considered an opportunistic plant pathogen, has rarely been described as causing disease in animals. This is the first report of S. proteamaculans causing severe necrotizing tracheitis and bronchopneumonia in a reptile.

Biocatalytic lipoprotein bioamphiphile induced treatment of recalcitrant hydrocarbons in petroleum refinery oil sludge through transposon technology

The present investigation employed transposon technology to enhance the degradation of recalcitrant petroleum hydrocarbons present in petroleum oil sludge by using biosurfactant hyper-producing strain Enterobacter xiangfangensis STP-3. Out of 2500 transposon induced mutants, mutants M_{257E.xiangfangensis} and M_{916E.xiangfangensis} hyper-produce biocatalytic lipoprotein biosurfactant by1.98 and 2.34 fold higher than wild-type strain. Transposon induced mutation also modified the amino acid composition which improved the hydrophobicity and thermal stability of the biosurfactants produced by mutants, compared to the wild-type biosurfactant. GC-MS and LC-MS-MS revealed that biosurfactants have pentameric lipid moiety and esterase as protein moiety. Increased biosurfactant hydrophobicity and yield by the mutants resulted in the enhanced bioavailability of petroleum hydrocarbons, thereby mutants M_{257E.xiangfangensis} and M_{916E.xiangfangensis} demonstrated better petroleum oil sludge degradation by 82% and 88% respectively, than wild-type (72%). Disrupted genes vgr G and pgm M in M257_{E.xiangfangensis} and M916_{E.xiangfangensis} respectively hyper-produce biosurfactant by competitive pathway inhibition and increased precursor availability mechanism. Hyper-production of biosurfactant was also validated by comparing the expression of biosynthetic genes ent E, ent F and est using qPCR. This is the first report on the application of transposon technology to hyper-produce biosurfactant for the effective bioremediation of hydrocarbon contaminated environments.

Characterization of a potent biosurfactant produced from Franconibacter sp. IITDAS19 and its application in enhanced oil recovery

Biosurfactants are surface-active molecules produced from microorganisms either on the cell surface or secreted extracellularly. Several biosurfactant producing microorganisms have been isolated to date, but they differ in their efficacy towards different types of hydrocarbons. Here, we report the isolation and characterization of a biosurfactant producing bacterium Franconibacter sp. IITDAS19 from crude oil contaminated soil. The biosurfactant was isolated, purified and characterized. It was identified as a glycolipid. It was found to be very stable at wide range of temperatures, pH and salt concentrations. It could reduce the surface tension of the water from 71 mN/m to 31 mN/m. IITDAS19 showed very high efficacy towards both aliphatic and aromatic hydrocarbons. It resulted in about 63% recovery of residual oil in a sand pack column. Our results suggested that the produced biosurfactant can be used for enhanced oil recovery. To our knowledge, this is the first report demonstrating the detailed characterization of a biosurfactant from Franconibacter spp.

Interactive analysis of biosurfactants in fruit-waste fermentation samples using BioSurfDB and MEGAN

Agroindustrial waste, such as fruit residues, are a renewable, abundant, low-cost, commonly-used carbon source. Biosurfactants are molecules of increasing interest due to their multifunctional properties, biodegradable nature and low toxicity, in comparison to synthetic surfactants. A better understanding of the associated microbial communities will aid prospecting for biosurfactant-producing microorganisms. In this study, six samples of fruit waste, from oranges, mangoes and mixed fruits, were subjected to autochthonous fermentation, so as to promote the growth of their associated microbiota, followed by short-read metagenomic sequencing. Using the DIAMOND+MEGAN analysis pipeline, taxonomic analysis shows that all six samples are dominated by Proteobacteria, in particular, a common core consisting of the genera Klebsiella, Enterobacter, Stenotrophomonas, Acinetobacter and Escherichia. Functional analysis indicates high similarity among samples and a significant number of reads map to genes that are involved in the biosynthesis of lipopeptide-class biosurfactants. Gene-centric analysis reveals Klebsiella as the main assignment for genes related to putisolvins biosynthesis. To simplify the interactive visualization and exploration of the surfactant-related genes in such samples, we have integrated the BiosurfDB classification into MEGAN and make this available. These results indicate that microbiota obtained from autochthonous fermentation have the genetic potential for biosynthesis of biosurfactants, suggesting that fruit wastes may provide a source of biosurfactant-producing microorganisms, with applications in the agricultural, chemical, food and pharmaceutical industries.

Production of biosurfactants from agro-industrial waste and waste cooking oil in a circular bioeconomy: An overview

Waste generation is becoming a global concern owing to its adverse effects on environment and human health. The utilization of waste as a feedstock for production of value-added products has opened new avenues contributing to environmental sustainability. Microorganisms have been employed for production of biosurfactants as secondary metabolites by utilizing waste streams. Utilization of waste as a substrate significantly reduces the cost of overall process. Biosurfactant(s) derived from these processes can be utilized in environmental and different industrial sectors. This review focuses on global market of biosurfactants followed by discussion on production of biosurfactants from waste streams such as agro-industrial waste and waste cooking oil. The need for waste stream derived circular bioeconomy and scale up of biosurfactant production have been narrated with applications of biosurfactants in environment and industrial sectors. Road blocks and future directions for research have also been discussed.

Bioprocesses for the recovery of bioenergy and value-added products from wastewater: A review

Wastewater and activated sludge present a major challenge worldwide. Wastewater generated from large and small-scale industries, laundries, human residential areas and other sources is emerging as a main problem in sanitation and maintenance of smart/green cities. During the last decade, different technologies and processes have been developed to recycle and purify the wastewater. Currently, identification and fundamental consideration of development of more advanced microbial-based technologies that enable wastewater treatment and simultaneous resource recovery to produce bioenergy, biofuels and other value-added compounds (organic acids, fatty acids, bioplastics, bio-pesticides, bio-surfactants and bio-flocculants etc.) became an emerging topic. In the last several decades, significant development of bioprocesses and techniques for the extraction and recovery of mentioned valuable molecules and compounds from wastewater, waste biomass or sludge has been made. This review presents different microbial-based process routes related to resource recovery and wastewater application for the production of value-added products and bioenergy. Current process limitations and insights for future research to promote more efficient and sustainable routes for this under-utilized and continually growing waste stream are also discussed.

Lipopeptide production by Serratia marcescens SmSA using a Taguchi design and its application in enhanced heavy oil recovery

Biosurfactant production at reactor level by Serratia marcescens SmSA was optimized and evaluated to enhance the heavy oil recovery on carbonate rocks. Temperature, agitation, and carbon/nitrogen (C/N) ratio were evaluated to optimize biosurfactant production by using a Taguchi (L9) design. The best conditions (C/N ratio: 6, 25 °C, and agitation: 100 rpm) were used to scale up the biosurfactant production with a 3-L bioreactor. The best aeration for biosurfactant production was 0.66 volume of air per volume of liquid per minute (vvm), producing the lowest surface tension (26 mN/m) in 14 h, with a biosurfactant yield of 14.26 g/L as a crude product and 2.85 g/L as a purified product, and a critical micelle concentration of 280 mg/L. The biosurfactant was characterized as a lipopeptide, and it was stable under extreme conditions: pH (2-12), salinity up to 200 g/L, and temperature up to 150 °C confirmed by thermogravimetric analysis. Enhanced oil recovery test was carried out with a carbonate core and heavy oil under reservoir conditions, obtaining an additional recovery of 8%, due to reduced interfacial tension and modified wettability of the rock. These findings highlight the potential application of S. marcescens SmSA biosurfactant in enhanced oil recovery.

Exploiting Microbes in the Petroleum Field: Analyzing the Credibility of Microbial Enhanced Oil Recovery (MEOR)

Crude oil is a major energy source that is exploited globally to achieve economic growth. To meet the growing demands for oil, in an environment of stringent environmental regulations and economic and technical pressure, industries have been required to develop novel oil salvaging techniques. The remaining ~70% of the world’s conventional oil (one-third of the available total petroleum) is trapped in depleted and marginal reservoirs, and could thus be potentially recovered and used. The only means of extracting this oil is via microbial enhanced oil recovery (MEOR). This tertiary oil recovery method employs indigenous microorganisms and their metabolic products to enhance oil mobilization. Although a significant amount of research has been undertaken on MEOR, the absence of convincing evidence has contributed to the petroleum industry’s low interest, as evidenced by the issuance of 400+ patents on MEOR that have not been accepted by this sector. The majority of the world’s MEOR field trials are briefly described in this review. However, the presented research fails to provide valid verification that the microbial system has the potential to address the identified constraints. Rather than promising certainty, MEOR will persist as an unverified concept unless further research and investigations are carried out.

Rhamnolipids Sustain Unchanged Surface Activities during Decomposition in Alkaline Solutions

Biosurfactant rhamnolipids (RLs) have gained global interests owing to their fully green properties, potentially wide applications in diverse fields, as well as high stabilities under various harsh conditions. Nevertheless, we doubted the reputed stability of RLs in considering their natural structure of carbohydrate heads and lipid tails. This study, for the first time, systematically investigated the stability of RLs at varying temperatures and pH. As found, the concentration of RLs in an aqueous solution was significantly reduced when the pH was over 11 at room temperature, and this was much more severe with the increase in temperature and preservation time. According to the high-performance liquid chromatography-mass spectrometry (HPLC-MS) analysis, degradation yielded other RL congeners, 3-hydroxy fatty acids, rhamnose, methyl furfural, and organic acids. The newly generated RL congeners and fatty acids still possessed equivalent surface activities in reducing the surface tension of the aqueous solution, well explaining the previously claimed high stability of RLs. The finding will be greatly valued for commercially developing the industrial applications of RLs and other biosurfactants.

Biosurfactants produced from corncob: a bibliometric perspective of a renewable and promising substrate

The reuse of agro-industrial waste has been a recurring issue since the 20th century. With a composition rich in carbohydrates and because of the massive amount of residue produced daily all over the world, corncob became a low-cost and suitable substrate to produce high added-value compounds. Biosurfactants are bioproducts of versatile applications due to their chemical structure with hydrophilic and hydrophobic regions. The current work performed a bibliometric analysis to identify research related to the synthesis of biosurfactants using corncob as substrate. Despite the high availability of corncobs, only nine articles were found in Scopus and Web of Science using different pretreatment processes and microorganisms. After an initial screening, data regarding research organizations, scientific journals, citations, countries, institutions, and keywords were analyzed. Results indicated that corncobs were also used to produce enzymes, adsorbents, activated carbon, and furfural. The presented evaluation updated the status of art, identifying a serious need for more research, especially because of corncob's high potential to provide fermentable sugars and the wide range of variables influencing fermentation processes that still need to be studied. A future association of this low-cost substrate with other methods can result in a promising scenario for technology transference.

Microbial glycoconjugates in organic pollutant bioremediation: recent advances and applications

The large-scale application of organic pollutants (OPs) has contaminated the air, soil, and water. Persistent OPs enter the food supply chain and create several hazardous effects on living systems. Thus, there is a need to manage the environmental levels of these toxicants. Microbial glycoconjugates pave the way for the enhanced degradation of these toxic pollutants from the environment. Microbial glycoconjugates increase the bioavailability of these OPs by reducing surface tension and creating a solvent interface. To date, very little emphasis has been given to the scope of glycoconjugates in the biodegradation of OPs. Glycoconjugates create a bridge between microbes and OPs, which helps to accelerate degradation through microbial metabolism. This review provides an in-depth overview of glycoconjugates, their role in biofilm formation, and their applications in the bioremediation of OP-contaminated environments.

Biosurfactant production from newly isolated Rhodotorula sp.YBR and its great potential in enhanced removal of hydrocarbons from contaminated soils

One of the very promising methods in the field of bioremediation of hydrocarbons is the application of biosurfactant- producing microorganisms based on the use of wastewater as renewable substrates of culture media, contributing to the reduction of costs. With this aim, the production, characterization and properties of the yeast strain YBR producing a biosurfactant newly isolated from an oilfield in Algeria, using wastewater from olive oil mills (OOMW) as a substrate for a low-cost and effective production, have been investigated. Screening of biosurfactant production was carried out with different tests, including emulsification index test (E24), drop collapse test, oil spreading technique and measurement of surface tension (ST). The isolated yeast strain was found to be a potent biosurfactant producer with E24 = 69% and a significant reduction in ST from 72 to 35 mN m^-1. The study of the cultural, biochemical, physiological and genetic characteristics of the isolate allowed us to identify it as Rhodotorula sp. strain YBR. Fermentation was carried out in a 2.5 L Minifors Bioreactor using crude OOMW as culture medium, the E₂₄ value reached 90% and a reduction of 72 to 35 mN m^-1 in ST. A biosurfactant yield = 10.08 ± 0.38 g L^-1 was recorded. The characterization by semi-purification and thin layer chromatography (TLC) of the crude extract of biosurfactant showed the presence of peptides, carbohydrates and lipids in its structure. The crude biosurfactant exhibited interesting properties such as: low critical micellar concentration (CMC), significant reduction in ST and strong emulsifying activity. In addition, it has shown stability over a wide range of pH (2-12), temperature (4-100 °C) and salinity (1-10%). More interestingly, the produced biosurfactant has proven to be of great potential application in the remobilization of hydrocarbons from polluted soil with a removal rate of greater than 95%.

Characterization of low-cost glycolipoprotein biosurfactant produced by Lactobacillus plantarum 60 FHE isolated from cheese samples using food wastes through response surface methodology and its potential as antimicrobial, antiviral, and anticancer activities

Considering the need of new lactic acid bacteria (LAB) for the production of novel biosurfactant (BS) molecules, the current study brings out a new insight on the exploration of cheese samples for BS producers and process optimization for industrial applications. In view of this, Lactobacillus plantarum 60FHE, Lactobacillus paracasei 75FHE, and Lactobacillus paracasei 77FHE were selected as the most operative strains. The biosurfactants (BSs) described as glycolipoproteins via Fourier-transform infrared spectroscopy (FTIR) exhibited antimicrobial activity against the food-borne pathogens. L. plantarum 60FHE BS showed an anticancer activity against colon carcinoma cells and had a week antiviral activity against Hepatitis A virus. Furthermore, glycolipoprotein production was enhanced by 1.42-fold through the development of an optimized process using central composite design (CCD). Emulsifying activities were stable after 60-min incubation from 4 to 120 °C, at pH 2-12, and after the addition of NaCl (2-14%). Characterization by nuclear magnetic resonance spectroscopy (¹H NMR) revealed that BS produced from strain 60FHE was glycolipoprotein. L. plantarum produced mixed BSs determined by Liquid Chromatography/Mass Spectrometry (LC-MS). Thus, indicating that BS was applied as a microbial food prevention and biomedical. Also, L. plantarum 60FHE BS was achieved with the use of statistical optimization on inexpensive food wastes.

Genome Sequences of Serratia Strains Revealed Common Genes in Both Serratomolides Gene Clusters

Simple Summary

Biosurfactants are amphiphilic molecules produced by microorganisms with a hydrophilic and a hydrophobic group, able to reduce surface tension. These molecules are largely used in the environmental, food, pharmaceutical, medical, and cleaning industries, among others. Serratia strains are ubiquitous microorganisms with the ability to produce biosurfactants, such as serrawettins. These extracellular lipopeptides are described as biocides against many bacteria and fungi. This work used comparative genomics to determine the distribution and organization of the serrawettins W1 and W2 biosynthetic gene clusters in all the 84 publicly available genomes of the Serratia genus. Here, the serrawettin W1 gene clusters’ organization is reported for the first time. The serrawettin W1 biosynthetic gene swrW and serrawettin W2 biosynthetic gene swrA were present in 17 and 11 Serratia genomes, respectively. The same genes in the biosynthetic clusters frame the swrW and swrA biosynthetic genes. This work identified four genes common to all serrawettin gene clusters, highlighting their key potential in the serrawettins biosynthetic process.

Abstract

Serratia strains are ubiquitous microorganisms with the ability to produce serratomolides, such as serrawettins. These extracellular lipopeptides are described as biocides against many bacteria and fungi and may have a nematicidal activity against phytopathogenic nematodes. Serrawettins W1 and W2 from different strains have different structures that might be correlated with distinct genomic organizations. This work used comparative genomics to determine the distribution and the organization of the serrawettins biosynthetic gene clusters in all the 84 publicly available genomes of the Serratia genus. The serrawettin W1 and W2 gene clusters’ organization was established using antiSMASH software and compared with single and short data previously described for YD25^TSerratia. Here, the serrawettin W1 gene clusters’ organization is reported for the first time. The serrawettin W1 biosynthetic gene swrW was present in 17 Serratia genomes. Eighty different coding sequence (CDS) were assigned to the W1 gene cluster, 13 being common to all clusters. The serrawettin W2 swrA gene was present in 11 Serratia genomes. The W2 gene clusters included 68 CDS with 24 present in all the clusters. The genomic analysis showed the swrA gene constitutes five modules, four with three domains and one with four domains, while the swrW gene constitutes one module with four domains. This work identified four genes common to all serrawettin gene clusters, highlighting their essential potential in the serrawettins biosynthetic process.

Bioreactivity, Guttation and Agents Influencing Surface Tension of Water Emitted by Actively Growing Indoor Mould Isolates

The secretion of metabolites in guttation droplets by indoor moulds is not well documented. This study demonstrates the guttation of metabolites by actively growing common indoor moulds. Old and fresh biomasses of indoor isolates of Aspergillus versicolor, Chaetomium globosum, Penicillium expansum, Trichoderma atroviride, T. trixiae, Rhizopus sp. and Stachybotrys sp. were compared. Metabolic activity indicated by viability staining and guttation of liquid droplets detected in young (<3 weeks old) biomass were absent in old (>6 months old) cultures consisting of dehydrated hyphae and dormant conidia. Fresh (<3 weeks old) biomasses were toxic more than 10 times towards mammalian cell lines (PK-15 and MNA) compared to the old dormant, dry biomasses, when calculated per biomass wet weight and per conidial particle. Surfactant activity was emitted in exudates from fresh biomass of T. atroviride, Rhizopus sp. and Stachybotrys sp. Surfactant activity was also provoked by fresh conidia from T. atroviride and Stachybotrys sp. strains. Water repealing substances were emitted by cultures of P. expansum, T. atroviride and C. globosum strains. The metabolic state of the indoor fungal growth may influence emission of liquid soluble bioreactive metabolites into the indoor air.

Production and potential biotechnological applications of microbial surfactants: An overview

Microbial surfactants are amphipathic molecules that consist of hydrophilic and hydrophobic domains, which allow partition of two fluid phases of varying degree of polarity. They are classified into two main groups: bioemulsifier and biosurfactant, depending on their molecular weight. Microbial surfactants occur in various categories according to their chemical nature and producing organisms. These biomolecules are produced by diverse groups of microorganisms including fungi, bacteria, and yeasts. Their production is significantly influenced by substrate type, fermentation technology and microbial strains. Owing to inherent multifunctional properties and assorted synthetic aptitude of the microbes, microbial surfactants are mostly preferred than their chemical counterparts for various industrial and biomedical applications including bioremediation, oil recovery; as supplements in laundry formulations and as emulsion-stabilizers in food and cosmetic industries as well as therapeutic agents in medicine. The present review discusses on production of microbial surfactants as promising and alternative broad-functional biomolecules for various biotechnological applications.

Improving bioremediation process of petroleum wastewater using biosurfactants producing Stenotrophomonas sp. S1VKR-26 and assessment of phytotoxicity

Primarily, this study aims to evaluate the biosurfactant production capability of Stenotrophomonas sp. S1VKR-26, profiling of its bioremediation ability to remediate petroleum refinery wastewater in a lab-scale bioreactor and assessment of phytotoxicity of bioremediated petroleum wastewater. As a result, strain S1VKR-26 was found to produce 5.15 g L^-1 biosurfactant, CMC of 30 mg L^-1 and reduced the surface tension from 60.3 to 30.5 mN m^-1. Different PAHs like naphthalene (93%), phenanthrene (86%), fluoranthene (92%), and pyrene (98.3%), total petroleum hydrocarbons (72.33%) and phenolic compounds (93.06%) were significantly remediated from the wastewater after the treatment of strain S1VKR-26. Moreover, S1VKR-26 strain treated 1:1 diluted petroleum wastewater have higher germination (100%), vigor (486), and seedling (4.86 cm) compared to untreated wastewater. Therefore, the treatment of petroleum refinery wastewater with strain S1VKR-26 could be more effective in the sense of environmental safety and irrigation for crop production in agriculture.

Invasion of Epithelial Cells Is Correlated with Secretion of Biosurfactant via the Type 3 Secretion System (T3SS) of Shigella flexneri

Biosurfactants are amphipathic molecules produced by many microorganisms, usually bacteria, fungi, and yeasts. They possess the property of reducing the tension of the membrane interfaces. No studies have been conducted on Shigella species showing the role of biosurfactant-like molecules (BLM) in pathogenicity. The aim of this study is to assess the ability of Shigella environmental and clinical strains to produce BLM and investigate the involvement of biosurfactants in pathogenicity. Our study has shown that BLM are secreted in the extracellular medium with EI24 ranging from 80% to 100%. The secretion is depending on the type III secretion system (T3SS). Moreover, our results have shown that S. flexneri, S. boydii, and S. sonnei are able to interact with hydrophobic areas with 17.64%, 21.42%, and 22.22% hydrophobicity, respectively. BLM secretion is totally prevented due to inhibition of T3SS by 100 mM benzoic and 1.5 mg/ml salicylic acids. P. aeruginosa harboring T3SS is able to produce 100% of BLM in the presence or in the absence of both T3SS inhibitors. The secreted BLM are extractable with an organic solvent such as chloroform, and this could entirely be considered a lipopeptide or polypeptide compound. Secretion of BLM allows some Shigella strains to induce multicellular phenomena like "swarming."

Valorization of xylose-rich hydrolysate from rice straw, an agroresidue, through biosurfactant production by the soil bacterium Serratia nematodiphila

Biosurfactants, amphiphilic compounds that reduce interfacial tension in oil-aqueous mixtures, are used in the petroleum, pharmaceutical, food, and agriculture industries. Fermentative production of biosurfactants requires expensive sugar or lipid substrates. Lignocellulosic biomass is a relatively cheap and abundant agricultural residue that can be used as an alternative substrate. Currently, several million tonnes of rice and wheat straw are generated globally as agricultural residues, most of which is disposed by open-field burning thereby leading to severe environmental pollution. This study aimed to produce biosurfactants in xylose-rich hydrolysates generated from rice straw. The hydrolysate is also a byproduct of 2G biofuel processes that often goes underutilized. A soil bacterium capable of growing and producing biosurfactants in rice straw hydrolysates, which typically contain growth-inhibitory compounds such as furfural and hydroxymethyl furfural, was isolated. Interestingly, the organism, identified as Serratia nematodiphila, exhibited higher glycolipid formation (4.5 ± 0.6 gL^-1) in xylose-rich hydrolysate than in glucose-rich enzymatic hydrolysate (3.1 ± 0.2 gL^-1) despite the higher bacterial cell density observed with the latter. The biosurfactants were thermostable and possessed promising emulsifying property and anti-microbial activity against bacteria and yeast. Further optimization of C:N resulted in a 2.8-fold increase in glycolipid production from xylose-rich hydrolysates. This study demonstrates the production of glycolipid biosurfactants from lignocellulosic biomass, a low-cost substrate and offers a plausible strategy for the management of these residues. Further, it also provides insights into the generation of additional high-value compounds in a bioethanol biorefinery to improve its commercial feasibility.

Isolation and characterization of biosurfactant-producing Serratia marcescens ZCF25 from oil sludge and application to bioremediation

A biosurfactant (BS) is a surface-active metabolite that is secreted by microbial metabolism, and can be used as a substitute for chemically synthesized surfactants. The first and most critical step to the successful application of BSs is to isolate bacterial strains with strong BS-producing capabilities. In this study, a BS-producing Serratia marcescens ZCF25 was isolated from the sludge of an oil tanker. Through polyphasic characterization using Fourier-transform infrared spectroscopy, thin layer chromatography, and gas chromatography-mass spectrometry, the produced BS was classified as a lipopeptide; it can decrease the water surface tension from 72.0 to 29.50 mN m^-1 and has a critical micelle concentration of 220 mg/L. The BS showed a high tolerance over a wide range of pH (2-12), temperature (50-100 °C), and salinity (10-100 g/L). Furthermore, the inoculation of S. marcescens ZCF25 with fracturing flowback fluids could significantly (P < 0.05) reduce the chemical oxygen demand, concentration of alkanes, and concentration of polycyclic aromatic hydrocarbons, with removal efficiencies of 48.9%, 65.57%, and 64%, respectively. This is the first study on the application of BS-producing S. marcescens to treat fracturing flowback fluids. S. marcescens ZCF25 is a promising candidate for use in various industrial and bioremediation applications. Graphical abstract.

Production and Potential Applications of Bioconversion of Chitin and Protein-Containing Fishery Byproducts into Prodigiosin: A Review

The technology of microbial conversion provides a potential way to exploit compounds of biotechnological potential. The red pigment prodigiosin (PG) and other PG-like pigments from bacteria, majorly from Serratia marcescens, have been reported as bioactive secondary metabolites that can be used in the broad fields of agriculture, fine chemicals, and pharmacy. Increasing PG productivity by investigating the culture conditions especially the inexpensive carbon and nitrogen (C/N) sources has become an important factor for large-scale production. Investigations into the bioactivities and applications of PG and its related compounds have also been given increased attention. To save production cost, chitin and protein-containing fishery byproducts have recently been investigated as the sole C/N source for the production of PG and chitinolytic/proteolytic enzymes. This strategy provides an environmentally-friendly selection using inexpensive C/N sources to produce a high yield of PG together with chitinolytic and proteolytic enzymes by S. marcescens. The review article will provide effective references for production, bioactivity, and application of S. marcescens PG in various fields such as biocontrol agents and potential pharmaceutical drugs.

Surfactant exopolysaccharide of Ochrobactrum pseudintermedium C1 has antibacterial potential: Its bio-medical applications in vitro

Since the advent of biologics in human welfare various bio-molecules have been explored. Different bacterial exopolysaccharides have proved their worth in many industrial and commercial applications. In this perspective, while exploring a surfactant exopolysaccharide of Ochrobactrum pseudintermedium C1, it is strikingly observed that it possesses a potent antibacterial property which encourages its bio-medical applications. Following isolation and purification of the said exopolysaccharide, its structural configuration and functional attributes are studied by several analytical procedures involving FTIR, ¹³C- NMR, CHN-analysis, estimation of zeta potential, XRD-study and digital tensiometry. When treated with pathological samples in vitro, it distinctly elicits its antibacterial property by exhibiting a characteristic zone of inhibition. Combined with a standard antibiotic (like ciprofloxacin), it enhances the action of antibiotic also. Mechanism of its antibacterial action is evaluated by crystal violet entrapment assay with UV-vis spectrophotometry, bacterial cell viability assay by trypan blue staining and SEM study. Results show that its basic surfactant property, anionic character, crystalline nature and scaffolding architecture are supposed to facilitate its antibacterial property which is manifested by its capability of disrupting bacterial cell envelope causing eventual cell death. In the current global scenario, an increasing threat of antibiotic resistance is prevailing due to their indiscriminate use. If used as an adjuvant with a judicious dose of antibiotic, this bio-molecule might play a significant role in bio-medicine to combat such threat.

Heterologous Expression of Sfp-Type Phosphopantetheinyl Transferase is Indispensable in the Biosynthesis of Lipopeptide Biosurfactant

Phosphopantetheinyl transferases are of tremendous enthusiasm inferable from their fundamental parts in activating polyketide, fatty acid, and non-ribosomal peptide synthetase enzymes and additionally an increasing number of biotechnological applications. The present study reports the identification of sfp gene from the Paenibacillus sp. D9, which encompasses 693 bp encoding a 230-amino acid protein with a molecular weight of 25.3 kDa. The amino acid sequence Paenibacillus sp. D9 Sfp revealed more than 90% sequence identity to other Sfp proteins from other Paenibacillus. The sfp gene was cloned and recovered efficiently using affinity chromatography with maximal specific phosphopantetheinyl transferase activity at an optimal pH of 8.0 and temperature of 30 °C. The enzyme also exhibited stability under a wide-ranging pH and temperature. The presence of Zn²⁺, Cu²⁺, and Fe²⁺ ions improved the enzymatic activity, while other metals such as Ni²⁺, Co²⁺, and Mg²⁺ had inhibitory effects. The introduction of EDTA also displayed no inhibition. Kinetic parameters were obtained having values of 4.52 mg/mL, 35.33 U/mg, 3.64 s^-1, and 0.104 mM^-1 s^-1 for K_m, V_max, k_cat, and k_cat/K_m, respectively. The biosurfactant synthesized by the recombinant BioSp was found to be surface active, reducing the surface tension to 33.7 mN/m on the glucose substrate after 5 days of incubation at 37 °C. The recombinant Escherichia coli strain also exhibited an improvement in biosurfactant yield (1.11 g/L) when contrasted with 0.52 g/L from Paenibacillus sp. D9. High esterase activity of 2.55 IU/mL using p-nitrophenyl acetate was observed on the recombinant strain, as the protein connected with the release of the biosurfactant was observed to be an esterase. The characteristics of improved biosurfactant and esterase synthesis by hyper-producing recombinant strain possess numerous values from biotechnology standpoint.

Bioconversion of Agroindustrial Waste in the Production of Bioemulsifier by Stenotrophomonas maltophilia UCP 1601 and Application in Bioremediation Process

This study investigated the potential of the bacterium Stenotrophomonas maltophilia UCP 1601 to produce a new biomolecule with emulsifying properties by determining the hemolytic activity, obtaining a halo of 9 mm in blood agar. Fermentations were carried out in saline mineral medium supplemented with 10% waste soybean oil (WSO) and different concentrations of glucose, peptone, ZnCl2, and MgSO4, according to a 24 full-factorial design. The results showed that the best results were obtained in condition 6 (medium composed of 4% glucose, 1% peptone, 2.72% ZnCl2, and 2.46% MgSO4), with excellent high emulsification index of 82.74%, using burned motor oil. The emulsifying property of the biomolecule produced was confirmed by the emulsification index of 78.57, 54.07, and 58.62%, using soybean, corn, and diesel oils, respectively, and the stability at different values of pH, temperature, and NaCl concentrations. The yield of the produced bioemulsifier was 2.8 g/L, presenting an anionic character and polymeric nature (37.6% lipids, 28.2% proteins, and 14.7% carbohydrates), confirmed by FTIR. The new bioemulsifier demonstrated promising potential for bioremediation of hydrophobic contaminants in the environment, since it had the ability to reduce the viscosity of WSO and burned motor oil, as well as excellent dispersion capacity of the burned motor oil in water (69.94 cm2 of oil displacement area), and removing 71.7% of this petroleum derivative from sandy soil.

Biosurfactant: A new frontier for greener technology and environmental sustainability

Petroleum hydrocarbons, oil, heavy metals pollution is becoming additional severe problem due to the growing call for crude oil and crude oil products related products in several fields of application. Such pollution have fascinated much considerations and attractions as it leads to ecological damages in both marines, aquatic and terrestrial ecosystems. Thus, different techniques including chemical surfactants and complex technologies have been proposed for their clean up from the environment, which in turn has detrimental effects on the environment. As of late, biosurfactant compounds have added much deliberation since they are considered as a reasonable option and eco-accommodating materials for remediation technology. The present society is confronting a few difficulties of usage, authorizing ecological protection and environmental change for the next generations. Biosurfactants hold the special property of minimizing and reducing the interfacial tension of liquids. Such features endure biosurfactants to afford a major part in emulsification, de-emulsification, biodegradability, foam formation, washing performance, surface activity, and detergent formulation, which have potential applications in the diverse industrial set-up. Conversations on cost-effective technologies, renewable materials, novel synthesis, downstream, upstream, emerging characterization techniques, molecular, and genetical engineering are substantial to produce biosurfactant of quality and quantity. Therefore, greater attention is being paid to biosurfactant production by identifying their environmental, and biotechnological applications. Be that as it may, the extravagant cost drew in with biosurfactants biotechnological synthesis and recovery can hamper their application in those areas. Notwithstanding these costs, biosurfactants can be used as these parts shows outstandingly high benefits that can at present beat the expenses incurred in the initial purification and downstream processes. Biosurfactant production by microorganisms is relatively considered one of the crucial know-how for improvement, growth, advancement, and environmental sustainability of the 21st century. There is a developing conversation around environmental safety and the significant role that biosurfactants will progressively play soon, for instance, the use of renewable by-products as substrates, potential reduction, re-use and recycling of waste and waste products. The review confers the usefulness of biosurfactants in the removal of environmental contaminants and, consequently, expanding environmental safety and drive towards greener technology.

Microbial Surfactants: The Next Generation Multifunctional Biomolecules for Applications in the Petroleum Industry and Its Associated Environmental Remediation

Surfactants are a broad category of tensio-active biomolecules with multifunctional properties applications in diverse industrial sectors and processes. Surfactants are produced synthetically and biologically. The biologically derived surfactants (biosurfactants) are produced from microorganisms, with Pseudomonas aeruginosa, Bacillus subtilis Candida albicans, and Acinetobacter calcoaceticus as dominant species. Rhamnolipids, sophorolipids, mannosylerithritol lipids, surfactin, and emulsan are well known in terms of their biotechnological applications. Biosurfactants can compete with synthetic surfactants in terms of performance, with established advantages over synthetic ones, including eco-friendliness, biodegradability, low toxicity, and stability over a wide variability of environmental factors. However, at present, synthetic surfactants are a preferred option in different industrial applications because of their availability in commercial quantities, unlike biosurfactants. The usage of synthetic surfactants introduces new species of recalcitrant pollutants into the environment and leads to undesired results when a wrong selection of surfactants is made. Substituting synthetic surfactants with biosurfactants resolves these drawbacks, thus interest has been intensified in biosurfactant applications in a wide range of industries hitherto considered as experimental fields. This review, therefore, intends to offer an overview of diverse applications in which biosurfactants have been found to be useful, with emphases on petroleum biotechnology, environmental remediation, and the agriculture sector. The application of biosurfactants in these settings would lead to industrial growth and environmental sustainability.

Advances on research in the use of agro-industrial waste in biosurfactant production

Biosurfactants are amphiphilic molecules produced by a variety of microorganisms, including bacteria, yeast and filamentous fungi. Unlike chemically synthesized surfactants, biosurfactants present advantages, such as biodegradability, low toxicity, high selectivity and activity under extreme temperature, pH and salinity conditions, as well as a low critical micelle concentration. Moreover, they can be produced from agro-industrial waste and renewable sources. Their structural diversity and functional properties mean that they have potential applications in various industrial processes as wetting agents, dispersants, emulsifiers, foaming agents, food additives and detergents, as well as in the field of environmental biotechnology. However, opportunities for their commercialization have been limited due to the low yields obtained in the fermentation processes involved in their production as well as the use of refined raw materials, which means higher cost in production. In an attempt to solve these limitations on the commercialization of biosurfactants, various research groups have focused on testing the use of inexpensive alternative sources, such as agro-industrial waste, as substrates for the production of different biosurfactants. In addition to enabling the economical production of biosurfactants, the use of such waste aims to reduce the accumulation of compounds that cause environmental damage. This review shows advances in biosurfactant production carried out using different waste materials or by-products from agro-industrial activities.

Efficient simultaneous production of extracellular polyol esters of fatty acids and intracellular lipids from inulin by a deep-sea yeast Rhodotorula paludigena P4R5

BACKGROUND

Polyol esters of fatty acids (PEFA) are a kind of promising biosurfactants and mainly secreted by Rhodotorula strains. In addition, some strains of Rhodotorula are reliable producers of microbial lipid. Therefore, it is feasible to establish a one step fermentation process for efficient simultaneous production of PEFA and microbial lipids by a suitable Rhodotorula strain.

RESULTS

A newly isolated deep-sea yeast, Rhodotorula paludigena P4R5, was shown to simultaneously produce high level of intracellular lipid and extracellular PEFA. Under the optimized conditions, it could yield 48.5 g/L of PEFA and 16.9 g/L of intracellular lipid within 156 h from inulin during 10-L batch fermentation. The PEFA consisting of a mixture of mannitol esters of 3-hydroxy C14, C16 and C18 fatty acids with variable acetylation showed outstanding surface activity and emulsifying activity, while the fatty acids of the intracellular lipid were mainly C16 and C18 and could be high-quality feedstock for biodiesel production.

CONCLUSION

The deep-sea yeast strain R. paludigena P4R5 was an excellent candidate for efficient simultaneous of biosurfactants and biodiesel from inulin. Our results also suggested that the establishment of fermentation systems with multiple metabolites production was an effective approach to improve the profitability.

Characterization of Extracellular Biosurfactants Expressed by a Pseudomonas putida Strain Isolated from the Interior of Healthy Roots from Sida hermaphrodita Grown in a Heavy Metal Contaminated Soil

Pseudomonas putida E41 isolated from root interior of Sida hermaphrodita (grown on a field contaminated with heavy metals) showed high biosurfactant activity. In this paper, we describe data from mass spectrometry and genome analysis, to improve our understanding on the phenotypic properties of the strain. Supernatant derived from P. putida E41 liquid culture exhibited a strong decrease in the surface tension accompanied by the ability for emulsion stabilization. We identified extracellular lipopeptides, putisolvin I and II expression but did not detect rhamnolipids. Their presence was confirmed by matrix-assisted laser desorption and ionization (MALDI) TOF/TOF technique. Moreover, ten phospholipids (mainly phosphatidylethanolamines PE 33:1 and PE 32:1) which were excreted by vesicles were also detected. In contrast the bacterial cell pellet was dominated by phosphatidylglycerols (PGs), which were almost absent in the supernatant. It seems that the composition of extracellular (secreted to the environment) and cellular lipids in this strain differs. Long-read sequencing and complete genome reconstruction allowed the identification of a complete putisolvin biosynthesis pathway. In the genome of P. putida E41 were also found all genes involved in glycerophospholipid biosynthesis, and they are likely responsible for the production of detected phospholipids. Overall this is the first report describing the expression of extracellular lipopeptides (identified as putisolvins) and phospholipids by a P. putida strain, which might be explained by the need to adapt to the highly contaminated environment.

Characterization of a Surface-Active Protein Extracted from a Marine Strain of Penicillium chrysogenum

Marine microorganisms represent a reservoir of new promising secondary metabolites. Surface-active proteins with good emulsification activity can be isolated from fungal species that inhabit the marine environment and can be promising candidates for different biotechnological applications. In this study a novel surface-active protein, named Sap-Pc, was purified from a marine strain of Penicillium chrysogenum. The effect of salt concentration and temperature on protein production was analyzed, and a purification method was set up. The purified protein, identified as Pc13g06930, was annotated as a hypothetical protein. It was able to form emulsions, which were stable for at least one month, with an emulsification index comparable to that of other known surface-active proteins. The surface tension reduction was analyzed as function of protein concentration and a critical micellar concentration of 2 μM was determined. At neutral or alkaline pH, secondary structure changes were monitored over time, concurrently with the appearance of protein precipitation. Formation of amyloid-like fibrils of SAP-Pc was demonstrated by spectroscopic and microscopic analyses. Moreover, the effect of protein concentration, a parameter affecting kinetics of fibril formation, was investigated and an on-pathway involvement of micellar aggregates during the fibril formation process was suggested.