A pragmatic guide to multiphoton microscope design

Standardised Measurements for Monitoring and Comparing Multiphoton Microscope Systems

The goal of this protocol is to enable better characterisation of multiphoton microscopy hardware across a large user base. The scope of this protocol is purposefully limited to focus on hardware, touching on software and data analysis routines only where relevant. The intended audiences are scientists using and building multiphoton microscopes in their laboratories. The goal is that any scientist, not only those with optical expertise, can test whether their multiphoton microscope is performing well and producing consistent data over the lifetime of their system.

Cascaded domain multiphoton spatial frequency modulation imaging

Significance

Multiphoton microscopy is a powerful imaging tool for biomedical applications. A variety of techniques and respective benefits exist for multiphoton microscopy, but an enhanced resolution is especially desired. Additionally multiphoton microscopy requires ultrafast pulses for excitation, so optimization of the pulse duration at the sample is critical for strong signals.

Aim

We aim to perform enhanced resolution imaging that is robust to scattering using a structured illumination technique while also providing a rapid and easily repeatable means to optimize group delay dispersion (GDD) compensation through to the sample.

Approach

Spatial frequency modulation imaging (SPIFI) is used in two domains: the spatial domain (SD) and the wavelength domain (WD). The WD-SPIFI system is an in-line tool enabling GDD optimization that considers all material through to the sample. The SD-SPIFI system follows and enables enhanced resolution imaging.

Results

The WD-SPIFI dispersion optimization performance is confirmed with independent pulse characterization, enabling rapid optimization of pulses for imaging with the SD-SPIFI system. The SD-SPIFI system demonstrates enhanced resolution imaging without the use of photon counting enabled by signal to noise improvements due to the WD-SPIFI system.

Conclusions

Implementing SPIFI in-line in two domains enables full-path dispersion compensation optimization through to the sample for enhanced resolution multiphoton microscopy.

Identification of active spermatogenesis using a multiphoton microscope

BACKGROUND

The sperm retrieval rate of microdissection testicular sperm extraction varies from 25% to 60%. Therefore, it is necessary to establish objective selection criteria for identifying seminiferous tubules with spermatozoa.

OBJECTIVES

Our aim was to develop a method for identifying spermatogenesis without sectioning testicular tissues.

MATERIALS AND METHODS

Testicular tissues of 10-week-old normal rats were fixed with 4% paraformaldehyde. Fluorescent labeling of seminiferous tubule nuclei and F-actin was performed, and the specimens were observed without sectioning using a multiphoton microscope. Cryptorchid rats were used as a model lacking elongated spermatids. Multiphoton images were compared with images of normal seminiferous tubules. In addition, seminiferous tubules of 10-week-old normal rats were labeled by testicular interstitial injection of fluorescent probes and observed by a multiphoton microscope without fixation. Terminal deoxynucleotidyl transferase dUTP nick end labeling-stained images of normal and probe-injected testes were compared.

RESULTS

In fixed seminiferous tubules, elongated spermatids were identified. In addition, F-actin of apical ectoplasmic specialization was observed around elongated spermatids. Furthermore, spermatogenic stages were identified by an array of nuclei or F-actin. In cryptorchid testes, elongated spermatids and F-actin of the apical ectoplasmic specialization were not observed. In testes injected with fluorescent probes, F-actin of the apical ectoplasmic specialization was observed, and spermatogenic stages were identified without fixation. There was no significant difference in the number of terminal deoxynucleotidyl transferase dUTP nick end labeling-positive cells per seminiferous tubule between normal and probe-injected testes.

CONCLUSIONS

Seminiferous epithelium could be observed without sectioning of tissues by fluorescent probes and a multiphoton microscope. Active spermatogenesis was observed by labeling F-actin with and without fixation. Moreover, the toxicity of fluorescent probes was limited. Our method has a potential for live imaging of testicular tissue.

Super-resolution computational saturated absorption microscopy

Imaging beyond the diffraction limit barrier has attracted wide attention due to the ability to resolve previously hidden image features. Of the various super-resolution microscopy techniques available, a particularly simple method called saturated excitation microscopy (SAX) requires only simple modification of a laser scanning microscope: The illumination beam power is sinusoidally modulated and driven into saturation. SAX images are extracted from the harmonics of the modulation frequency and exhibit improved spatial resolution. Unfortunately, this elegant strategy is hindered by the incursion of shot noise that prevents high-resolution imaging in many realistic scenarios. Here, we demonstrate a technique for super-resolution imaging that we call computational saturated absorption (CSA) in which a joint deconvolution is applied to a set of images with diversity in spatial frequency support among the point spread functions (PSFs) used in the image formation with saturated laser scanning fluorescence microscopy. CSA microscopy allows access to the high spatial frequency diversity in a set of saturated effective PSFs, while avoiding image degradation from shot noise.

Tutorial: multiphoton microscopy to advance neuroscience research

Multiphoton microscopy (MPM) employs ultrafast infrared lasers for high-resolution deep three-dimensional imaging of live biological samples. The goal of this tutorial is to provide a practical guide to MPM imaging for novice microscopy developers and life-science users. Principles of MPM, microscope setup, and labeling strategies are discussed. Use of MPM to achieve unprecedented imaging depth of whole mounted explants and intravital imaging via implantable glass windows of the mammalian nervous system is demonstrated.

MEMS Enabled Miniature Two-Photon Microscopy for Biomedical Imaging

Over the last decade, two-photon microscopy (TPM) has been the technique of choice for in vivo noninvasive optical brain imaging for neuroscientific study or intra-vital microendoscopic imaging for clinical diagnosis or surgical guidance because of its intrinsic capability of optical sectioning for imaging deeply below the tissue surface with sub-cellular resolution. However, most of these research activities and clinical applications are constrained by the bulky size of traditional TMP systems. An attractive solution is to develop miniaturized TPMs, but this is challenged by the difficulty of the integration of dynamically scanning optical and mechanical components into a small space. Fortunately, microelectromechanical systems (MEMS) technology, together with other emerging micro-optics techniques, has offered promising opportunities in enabling miniaturized TPMs. In this paper, the latest advancements in both lateral scan and axial scan techniques and the progress of miniaturized TPM imaging will be reviewed in detail. Miniature TPM probes with lateral 2D scanning mechanisms, including electrostatic, electromagnetic, and electrothermal actuation, are reviewed. Miniature TPM probes with axial scanning mechanisms, such as MEMS microlenses, remote-focus, liquid lenses, and deformable MEMS mirrors, are also reviewed.

Multi-Photon Microscopy

In this series of papers on light microscopy imaging, we have covered the fundamentals of microscopy, super-resolution microscopy, and lightsheet microscopy. This last review covers multi-photon microscopy with a brief reference to intravital imaging and Brainbow labeling. Multi-photon microscopy is often referred to as two-photon microscopy. Indeed, using two-photon microscopy is by far the most common way of imaging thick tissues; however, it is theoretically possible to use a higher number of photons, and three-photon microscopy is possible. Therefore, this review is titled "multi-photon microscopy." Another term for describing multi-photon microscopy is "non-linear" microscopy because fluorescence intensity at the focal spot depends upon the average squared intensity rather than the squared average intensity; hence, non-linear optics (NLO) is an alternative name for multi-photon microscopy. It is this non-linear relationship (or third exponential power in the case of three-photon excitation) that determines the axial optical sectioning capability of multi-photon imaging. In this paper, the necessity for two-photon or multi-photon imaging is explained, and the method of optical sectioning by multi-photon microscopy is described. Advice is also given on what fluorescent markers to use and other practical aspects of imaging thick tissues. The technique of Brainbow imaging is discussed. The review concludes with a description of intravital imaging of the mouse. © 2023 Wiley Periodicals LLC.

Ultra-long anti-diffracting beam volume imaging using a single-photon excitation microscope

We studied a novel volumetric single-photon excitation microscope with an ultralong anti-diffracting (UAD) beam as illumination. Volumetric fluorescence image direct mapping showed that the axial imaging range of the UAD beam was approximately 14 times and 2 times that of conventional Gaussian and Airy beams, respectively, while maintaining a narrow lateral width. We compared the imaging capabilities of the Gaussian, Airy, and UAD modes through a strongly scattering environment mixed with fluorescent microspheres and agarose gel. Thick samples were scanned layer by layer in the Gaussian, Airy, and UAD modes, and then the three-dimensional structural information was projected onto a two-dimensional image. Benefiting from the longer focal length of the UAD beam, a deeper axial projection was provided, and the volume imaging speed was vastly increased. To demonstrate the performances of the UAD microscope, we performed dynamic volumetric imaging on the cardiovascular system of zebrafish labeled with green fluorescent proteins in the three modes and dynamically monitored substance transport in zebrafish blood vessels. In addition, the symmetrical curve trajectory of the UAD beam and the axial depth of the lateral position can be used for localization of micro-objects.

Computational framework for single-cell spatiotemporal dynamics of optogenetic membrane recruitment

We describe a modular computational framework for analyzing cell-wide spatiotemporal signaling dynamics in single-cell microscopy experiments that accounts for the experiment-specific geometric and diffractive complexities that arise from heterogeneous cell morphologies and optical instrumentation. Inputs are unique cell geometries and protein concentrations derived from confocal stacks and spatiotemporally varying environmental stimuli. After simulating the system with a model of choice, the output is convolved with the microscope point-spread function for direct comparison with the observable image. We experimentally validate this approach in single cells with BcLOV4, an optogenetic membrane recruitment system for versatile control over cell signaling, using a three-dimensional non-linear finite element model with all parameters experimentally derived. The simulations recapitulate observed subcellular and cell-to-cell variability in BcLOV4 signaling, allowing for inter-experimental differences of cellular and instrumentation origins to be elucidated and resolved for improved interpretive robustness. This single-cell approach will enhance optogenetics and spatiotemporally resolved signaling studies.

Development of a microstructured tissue phantom with adaptable optical properties for use with microscopes and fluorescence lifetime imaging systems

OBJECTIVES

For the development and validation of diagnostic procedures based on microscopic methods, knowledge about the imaging depth and achievable resolution in tissue is crucial. This poses the challenge to develop a microscopic artificial phantom focused on the microscopic instead of the macroscopic optical tissue characteristics.

METHODS

As existing artificial tissue phantoms designed for image forming systems are primarily targeted at wide field applications, they are unsuited for reaching the formulated objective. Therefore, a microscopy- and microendoscopy-suited artificial tissue phantom was developed and characterized. It is based on a microstructured glass surface coated with fluorescent beads at known depths covered by a scattering agent with modifiable optical properties. The phantom was examined with different kinds of microscopy systems in order to characterize its quality and stability and to demonstrate its usefulness for instrument comparison, for example, regarding structural as well as fluorescence lifetime analysis.

RESULTS

The analysis of the manufactured microstructured glass surfaces showed high regularity in their physical dimensions in accordance with the specifications. Measurements of the optical parameters of the scattering medium were consistent with simulations. The fluorescent beads coating proved to be stable for a respectable period of time (about a week). The developed artificial tissue phantom was successfully used to detect differences in image quality between a research microscope and an endoscopy based system. Plausible causes for the observed differences could be derived based on the well known microstructure of the phantom.

CONCLUSIONS

The artificial tissue phantom is well suited for the intended use with microscopic and microendoscopic systems. Due to its configurable design, it can be adapted to a wide range of applications. It is especially targeted at the characterization and calibration of clinical imaging systems that often lack extensive positioning capabilities such as an intrinsic z-stage.

Imaging neural circuit pathology of autism spectrum disorders: autism-associated genes, animal models and the application of in vivo two-photon imaging

Recent advances in human genetics identified genetic variants involved in causing autism spectrum disorders (ASDs). Mouse models that mimic mutations found in patients with ASD exhibit behavioral phenotypes consistent with ASD symptoms. These mouse models suggest critical biological factors of ASD etiology. Another important implication of ASD genetics is the enrichment of ASD risk genes in molecules involved in developing synapses and regulating neural circuit function. Sophisticated in vivo imaging technologies applied to ASD mouse models identify common synaptic impairments in the neocortex, with genetic-mutation-specific defects in local neural circuits. In this article, we review synapse- and circuit-level phenotypes identified by in vivo two-photon imaging in multiple mouse models of ASD and discuss the contributions of altered synapse properties and neural circuit activity to ASD pathogenesis.

Two-Photon Fluorescence Microscopy and Applications in Angiogenesis and Related Molecular Events

The role of angiogenesis in health and disease have gained considerable momentum in recent years. Visualizing angiogenic patterns and associated events of surrounding vascular beds in response to therapeutic and laboratory-grade biomolecules have become a commonplace in regenerative medicine and the biosciences. To aid imaging investigations in angiogenesis, the two-photon excitation fluorescence microscopy (2PEF), or multiphoton fluorescence microscopy is increasingly utilized in scientific investigations. The 2PEF microscope confers several distinct imaging advantages over other fluorescence excitation microscopy techniques - for the observation of in-depth, three-dimensional vascularity in a variety of tissue formats, including fixed tissue specimens and in vivo vasculature in live specimens. Understanding morphological and subcellular changes that occur in cells and tissues during angiogenesis will provide insights to behavioral responses in diseased states, advance the engineering of physiologically-relevant tissue models and provide biochemical clues for the design of therapeutic strategies. We review the applicability and limitations of the 2PEF microscope on the biophysical and molecular-level signatures of angiogenesis in various tissue models. Imaging techniques and strategies for best practices in 2PEF microscopy will be reviewed.

Miniaturized multimodal multiphoton microscope for simultaneous two-photon and three-photon imaging with a dual-wavelength Er-doped fiber laser

A multimodal multiphoton microscopy (MPM) is developed to acquire both two-photon microscopy (2PM) and three-photon microscopy (3PM) signals. A dual-wavelength Er-doped fiber laser is used as the light source, which provides the fundamental pulse at 1580 nm to excite third harmonic generation (THG) and the frequency-doubled pulse at 790 nm to excite intrinsic two-photon excitation fluorescence (TPEF) and second harmonic generation (SHG). Due to their different contrast mechanisms, the TPEF, SHG, and THG images can acquire complementary information about tissues, including cells, collagen fibers, lipids, and interfaces, all label-free. The compact MPM imaging probe is developed using miniature objective lens and a micro-electro-mechanical scanner. Furthermore, the femtosecond laser pulses are delivered by a single mode fiber and the signals are collected by a multimode fiber, which makes the miniaturized MPM directly fiber-coupled, compact, and portable. Design considerations on using the dual excitation wavelengths are discussed. Multimodal and label-free imaging by TPEF, SHG, and THG are demonstrated on biological samples. The miniaturized multimodal MPM is shown to have great potential for label-free imaging of thick and live tissues.

Two-dimensional random access multiphoton spatial frequency modulated imaging

Spatial frequency modulated imaging (SPIFI) enables the use of an extended excitation source for linear and nonlinear imaging with single element detection. To date, SPIFI has only been used with fixed excitation source geometries. Here, we explore the potential for the SPIFI method when a spatial light modulator (SLM) is used to program the excitation source, opening the door to a more versatile, random access imaging environment. In addition, an in-line, quantitative pulse compensation and measurement scheme is demonstrated using a new technique, spectral phase and amplitude retrieval and compensation (SPARC). This enables full characterization of the light exposure conditions at the focal plane of the random access imaging system, an important metric for optimizing, and reporting imaging conditions within specimens.

Fluorescence anisotropy imaging in drug discovery

Non-invasive measurement of drug-target engagement can provide critical insights in the molecular pharmacology of small molecule drugs. Fluorescence polarization/fluorescence anisotropy measurements are commonly employed in protein/cell screening assays. However, the expansion of such measurements to the in vivo setting has proven difficult until recently. With the advent of high-resolution fluorescence anisotropy microscopy it is now possible to perform kinetic measurements of intracellular drug distribution and target engagement in commonly used mouse models. In this review we discuss the background, current advances and future perspectives in intravital fluorescence anisotropy measurements to derive pharmacokinetic and pharmacodynamic measurements in single cells and whole organs.

Interferometric spatial frequency modulation imaging

Interferometric spatial frequency modulation for imaging (I-SPIFI) is demonstrated for the first time, to our knowledge. Significantly, this imaging modality can be seamlessly combined with nonlinear SPIFI imaging and operates through single-element detection, making it compatible for use in scattering specimens. Imaging dynamic processes with submicrometer axial resolution through long working distance optics is shown, and high contrast images compared to traditional wide-field microscopy images. Finally, enhanced lateral resolution is achieved in I-SPIFI. To our knowledge, this is the first single platform that enables multimodal linear and nonlinear imaging, with enhanced resolution, all of which can be performed simultaneously.

Fabrication and characterization of modulation masks for multimodal spatial frequency modulated microscopy

Spatial frequency modulated imaging (SPIFI) is a powerful imaging method that when used in conjunction with multiphoton contrast mechanisms has the potential to improve the spatial and temporal scales that can be explored within a single nonlinear optical microscope platform. Here we demonstrate, for the first time to our knowledge, that it is possible to fabricate inexpensive masks using femtosecond laser micromachining that can be readily deployed within the multiphoton microscope architecture to transform the system from a traditional point-scanning system to SPIFI and gain the inherent advantages that follow.

All-reflective multiphoton microscope

We present the design, construction, and characterization of a multiphoton microscope that uses reflective elements for beam shaping and steering. This compact all reflective design removes the adverse effects of dispersion on laser pulse broadening as well as chromatic aberration in the focusing of broadband and multicolored laser sources. The design of this system is discussed in detail, including aberrations analysis via ray-tracing simulation and opto-mechanical design. The resolution of this mirror based all-reflective microscope is characterized using fluorescent microbeads. The performance of the system at multiple wavelengths is investigated along with some potential multiphoton imaging and writing applications.

An Assemblable, Multi-Angle Fluorescence and Ellipsometric Microscope

We introduce a multi-functional microscope for research laboratories that have significant cost and space limitations. The microscope pivots around the sample, operating in upright, inverted, side-on and oblique geometries. At these geometries it is able to perform bright-field, fluorescence and qualitative ellipsometric imaging. It is the first single instrument in the literature to be able to perform all of these functionalities. The system can be assembled by two undergraduate students from a provided manual in less than a day, from off-the-shelf and 3D printed components, which together cost approximately $16k at 2016 market prices. We include a highly specified assembly manual, a summary of design methodologies, and all associated 3D-printing files in hopes that the utility of the design outlives the current component market. This open design approach prepares readers to customize the instrument to specific needs and applications. We also discuss how to select household LEDs as low-cost light sources for fluorescence microscopy. We demonstrate the utility of the microscope in varied geometries and functionalities, with particular emphasis on studying hydrated, solid-supported lipid films and wet biological samples.

Improving data quality in neuronal population recordings

Understanding how the brain operates requires understanding how large sets of neurons function together. Modern recording technology makes it possible to simultaneously record the activity of hundreds of neurons, and technological developments will soon allow recording of thousands or tens of thousands. As with all experimental techniques, these methods are subject to confounds that complicate the interpretation of such recordings, and could lead to erroneous scientific conclusions. Here we discuss methods for assessing and improving the quality of data from these techniques and outline likely future directions in this field.