Effect of surface roughness on osteogenesis in vitro and osseointegration in vivo of carbon fiber-reinforced polyetheretherketone-nanohydroxyapatite composite

A self-assembling graphene oxide coating for enhanced bactericidal and osteogenic properties of poly-ether-ether-ketone

Poly-ether-ether-ketone (PEEK) is a biomedical plastic that can be used for orthopedic implants, but it offers poor antibacterial properties and bioactivity. In this study, PEEK was sulfonated with the obtained porous structure adsorbing graphene oxide (GO). The surface microstructures and properties of the original PEEK, sulfonated PEEK (SPEEK), and GO-grafted PEEK (GO-SPEEK) were characterized. The results revealed that the GO-SPEEK surface is a 3D porous structure exhibiting superior hydrophilicity to the original PEEK. Although SPEEK was shown to possess antimicrobial properties against both Escherichia coli and Staphylococcus aureus, the bactericidal effect was even more significant for GO-SPEEK, at about 86% and 94%, respectively. In addition, the in vitro simulated-body-fluid immersion and cell experiments indicated that GO-SPEEK had much better hydroxyapatite (HA)-precipitation induction capacity and cell-material interactions (e.g., cell adhesion, proliferation, osteodifferentiation, and extracellular matrix mineralization. The tensile test revealed that the mechanical properties of PEEK were maintained after surface modification, as GO-SPEEK has comparable values of elastic modulus and tensile strength to PEEK. Our investigation sought a method to simultaneously endow PEEK with both good antimicrobial properties and bioactivity as well as mechanical properties, providing a theoretical basis for developing high-performance orthopedic implants in the clinic.

Hydrothermally treated coral scaffold promotes proliferation of mesenchymal stem cells and enhances segmental bone defect healing

Introduction: Synthetic hydroxyapatite (HAp) scaffolds have shown promising therapeutic outcomes in both animals and patients. In this study, we aim to evaluate the chemical and physical phenotype, biocompatibility, and bone repair effects of hydrothermally treated coral with natural coral and synthetic HAp. Methods: The phase composition, surface pattern, 3D structures, and porosity of the scaffolds were characterized, and cell viability, proliferation, and osteogenic differentiation of mesenchymal stem cells (MSCs) after seeding onto the scaffold were determined. The scaffolds were implanted into rats to assess their bone repair effects using micro-CT analysis, mechanical testing, and histological staining. Results: The results showed that the phase composition, porous structure, and porosity of hydrothermally treated coral were comparable to pure HAp scaffold. While only the natural coral happens to be dominantly calcium carbonate. Higher cell proliferation and osteogenic differentiation potential were observed in the hydrothermally treated coral scaffold compared to natural coral and pure HAp. Histological results also showed increased new bone formation in the hydrothermally treated coral group. Discussion: Overall, our study suggests that hydrothermal modification enhances the cytocompatibility and therapeutic capacity of coral without altering its physical properties, showing superior effectiveness in bone repair to synthetic HAp.

Chitosan-Reinforced Gelatin Microspheres-Modified Glass Ionomer Cement (GIC): A Novel Bone Alloplast Graft Material Synthesis and an In Vivo Analysis

Aim and objective The study aimed to assess and evaluate the efficacy of glass ionomer modified with chitosan-reinforced gelatin microspheres on bone formation. Materials and methods  The study involved three groups: Group I comprised plain glass ionomer cement; Group II comprised glass ionomer cement/gelatin (70:30 wt%); in Group III, glass ionomer cement/gelatin/chitosan (70:30%) scaffold were made into discs; the gelatin microspheres were synthesized by oil emulsion method. The synthesized scaffold was subjected to the following in vitro testing, Instron Universal Testing Machine (UTM), U3000, (Instron Corporation, Norwood, Massachusetts, United States) to assess compressive strength, scanning electron microscope (SEM) examination, and biocompatibility testing using hemocompatibility assay. The material was then tested in vivo; male Wistar albino rats, a total of nine animals, were utilized for this purpose. Three animals were used in each group; a femoral defect model was the model of choice for the experiment and the animals were observed for a period of four weeks, following which the animals were sacrificed and sent for histopathological analysis. Results The compression testing was carried out using UTM; test group I was 33 MPa, test group II was 2.3 MPa, and test group III was 25.75 MPa. SEM (JSM-IT800 Schottky Field Emission NANO SEM (JEOL, Tokyo, Japan)) analysis was done to observe the porosity of the fabricated scaffold with the average measurement of 0.12 ± 0.2 μm in test group II and 0.29 ± 0.4 μm in test group III. Hemocompatibility reports noted 0.4-0.8% lysis for the synthesized scaffolds. Histopathology staining of the femur defects showed that group III favoured bone formation. One-way analysis of variance (ANOVA) and post hoc Bonferroni test was done on the data. The optical density values of the alizarin red stained slide showed statistical significance for group III. Conclusion In conclusion, the synthesized scaffolds are biocompatible, distribution of porosity and pore characteristics in the glass ionomer cement/gelatin/chitosan group is better than that of the glass ionomer cement/gelatin group. The glass ionomer cement/gelatin/chitosan group had better compressive strength and induced more bone formation compared to the other test group and the control. Thus, the novel glass ionomer modified with chitosan-reinforced gelatin microspheres has optimal properties to be used as a bone graft material.

Enhancing bone tissue engineering with 3D-Printed polycaprolactone scaffolds integrated with tragacanth gum/bioactive glass

Tissue-engineered bone substitutes, characterized by favorable physicochemical, mechanical, and biological properties, present a promising alternative for addressing bone defects. In this study, we employed an innovative 3D host-guest scaffold model, where the host component served as a mechanical support, while the guest component facilitated osteogenic effects. More specifically, we fabricated a triangular porous polycaprolactone framework (host) using advanced 3D printing techniques, and subsequently filled the framework's pores with tragacanth gum-45S5 bioactive glass as the guest component. Comprehensive assessments were conducted to evaluate the physical, mechanical, and biological properties of the designed scaffolds. Remarkably, successful integration of the guest component within the framework was achieved, resulting in enhanced bioactivity and increased strength. Our findings demonstrated that the scaffolds exhibited ion release (Si, Ca, and P), surface apatite formation, and biodegradation. Additionally, in vitro cell culture assays revealed that the scaffolds demonstrated significant improvements in cell viability, proliferation, and attachment. Significantly, the multi-compartment scaffolds exhibited remarkable osteogenic properties, indicated by a substantial increase in the expression of osteopontin, osteocalcin, and matrix deposition. Based on our results, the framework provided robust mechanical support during the new bone formation process, while the guest component matrix created a conducive micro-environment for cellular adhesion, osteogenic functionality, and matrix production. These multi-compartment scaffolds hold great potential as a viable alternative to autografts and offer promising clinical applications for bone defect repair in the future.

Research progress of 3D printed poly (ether ether ketone) in the reconstruction of craniomaxillofacial bone defects

The clinical challenge of bone defects in the craniomaxillofacial region, which can lead to significant physiological dysfunction and psychological distress, persists due to the complex and unique anatomy of craniomaxillofacial bones. These critical-sized defects require the use of bone grafts or substitutes for effective reconstruction. However, current biomaterials and methods have specific limitations in meeting the clinical demands for structural reinforcement, mechanical support, exceptional biological performance, and aesthetically pleasing reconstruction of the facial structure. These drawbacks have led to a growing need for novel materials and technologies. The growing development of 3D printing can offer significant advantages to address these issues, as demonstrated by the fabrication of patient-specific bioactive constructs with controlled structural design for complex bone defects in medical applications using this technology. Poly (ether ether ketone) (PEEK), among a number of materials used, is gaining recognition as a feasible substitute for a customized structure that closely resembles natural bone. It has proven to be an excellent, conformable, and 3D-printable material with the potential to replace traditional autografts and titanium implants. However, its biological inertness poses certain limitations. Therefore, this review summarizes the distinctive features of craniomaxillofacial bones and current methods for bone reconstruction, and then focuses on the increasingly applied 3D printed PEEK constructs in this field and an update on the advanced modifications for improved mechanical properties, biological performance, and antibacterial capacity. Exploring the potential of 3D printed PEEK is expected to lead to more cost-effective, biocompatible, and personalized treatment of craniomaxillofacial bone defects in clinical applications.

Biocompatibility of fiber-reinforced composite (FRC) and woven-coated FRC: an in vivo study

OBJECTIVES

To investigate biocompatibility and bone contact area of FRC and woven-coated FRC (FRC-C) in rats.

MATERIALS AND METHODS

Sixty rats were allocated to three groups: FRC (n=20), FRC-C (n=20), and control group (n=20). Subgroups were determined as 4th (n=10) and 12th weeks (n=10). The specimens were placed in the femur of rats. In the control group, the bone defects were left empty and sutured. Four and 12 weeks after implantation, the rats were sacrificed. Histopathological examinations were performed in a semi-quantitative manner. Twenty rats (n=20) were used for scanning electron microscopy (SEM) examination. Bone contact surfaces were calculated in SEM analysis. A chi-square test was performed to analyze the data.

RESULTS

No statistical difference was detected between the 4th and 12th weeks in the quality of bone union. Quality of bone union was lower in FRC compared to the control group in the 4th week (p=0.012) and the 12th week (p=0.017). The periosteal reaction at the 12th week was lower in FRC than in the control group (p=0.021). Bone contact of FRC and FRC-C was 85.5% and 86.3%, respectively.

CONCLUSIONS

FRC and FRC-C were biocompatible and showed no inflammation. The woven coating did not increase the quality of bone union and bone contact area, while not reducing biocompatibility.

CLINICAL RELEVANCE

The biocompatibility and good bone response of the woven glass fiber net were demonstrated to have the potential as a scaffold for the augmentation of alveolar bone deficiencies and the reconstruction of maxillofacial defects.

Development of Gelatin-Based Shape-Memory Polymer Scaffolds with Fast Responsive Performance and Enhanced Mechanical Properties for Tissue Engineering Applications

Shape-memory polymers (SMPs) can be defined as a reversibly changing form through deformation and recovery by external stimuli. However, there remain application limitations of SMPs, such as complicated preparation processes and slow shape recovery. Here, we designed gelatin-based shape-memory scaffolds by a facile dipping method in tannic acid solution. The shape-memory effect of scaffolds was attributed to the hydrogen bond between gelatin and tannic acid, which acts as the net point. Moreover, gelatin (Gel)/oxidized gellan gum (OGG)/calcium chloride (Ca) was intended to induce faster and more stable shape-memory behavior through the introduction of a Schiff base reaction. The chemical, morphological, physicochemical, and mechanical properties of the fabricated scaffolds were evaluated, and those results showed that the Gel/OGG/Ca had improved mechanical properties and structural stability compared with other scaffold groups. Additionally, Gel/OGG/Ca exhibited excellent shape-recovery behavior of 95.8% at 37 °C. As a consequence, the proposed scaffolds can be fixed to the temporary shape at 25 °C in just 1 s and recovered to the original shape at 37 °C within 30 s, implying a great potential for minimally invasive implantation.

Assessing biocompatibility & mechanical testing of 3D-printed PEEK versus milled PEEK

Objectives

To compare mechanical properties of 3D-printed and milled poly-ether-ether-ketone (PEEK) materials. To define post-production treatments to enhance biocompatibility of 3D-printed PEEK.

Methods

Standardised PEEK samples were produced via milling and fused-deposition-modelling 3D-printing. To evaluate mechanical properties, tensile strength, maximum flexural strength, fracture toughness, and micro-hardness were measured.3D printed samples were sandblasted with 50 or 125 μm aluminium oxide beads to increase biocompatibility.Scanning electron microscopy (SEM) evaluated microstructure of 3D-printed and sandblasted samples, estimating surface roughness at scales from 1mm-1μm.Cell adhesion on 3D printed and sandblasted materials was evaluated by culturing primary human endothelial cells and osteoblasts (HUVEC, HOBS) and evaluating cell growth over 48 h.

Results

3D printed materials had lower tensile strength, flexural strength, and fracture toughness, but higher micro-hardness.SEM analysis of 3D-printed surfaces showed sandblasting with 125 and 50 μm silica particles removed printing defects and created roughened surfaces for increased HUVEC and HOBs uniform cell adhesion and distribution. No cytotoxicity was observed over a 48h period, and all cells demonstrated >95% viability.

Clinical significance

3D-printing of PEEK is an emerging technology with clear advantages over milling in maxillofacial implant production. Nonetheless, this manufacturing modality may produce 3D printed PEEK devices with lower mechanical resistance parameters compared to milled PEEK but with values compatible with natural bone. PEEK has poor osteoconductivity and ability to osseointegrate. Sandblasting is an inexpensive modality to remove irregular surface defects and create uniform micro-rough surfaces supporting cell attachment and potentially enhancing integration of PEEK implants with host tissue.

3D-Printing for Critical Sized Bone Defects: Current Concepts and Future Directions

The management and definitive treatment of segmental bone defects in the setting of acute trauma, fracture non-union, revision joint arthroplasty, and tumor surgery are challenging clinical problems with no consistently satisfactory solution. Orthopaedic surgeons are developing novel strategies to treat these problems, including three-dimensional (3D) printing combined with growth factors and/or cells. This article reviews the current strategies for management of segmental bone loss in orthopaedic surgery, including graft selection, bone graft substitutes, and operative techniques. Furthermore, we highlight 3D printing as a technology that may serve a major role in the management of segmental defects. The optimization of a 3D-printed scaffold design through printing technique, material selection, and scaffold geometry, as well as biologic additives to enhance bone regeneration and incorporation could change the treatment paradigm for these difficult bone repair problems.

Comparison of the Biological Behavior and Topographical Surface Assessment of a Minimally Invasive Dental Implant and a Standard Implant: An In Vitro Study

The current study aimed to assess the topographical and physical properties of a minimally invasive implant (MagiCore®: MC®, InnosBioSurg, IBS) and to evaluate its biological behavior compared to a gold standard implant (NobelParallel™: NB™, Nobel Biocare™). After surface characterization, the biological behavior assessment was conducted regarding human gingival fibroblasts (hGF) and osteoblast-like cells (MG63). Roughness values for NBTM were Ra = 1.28 µm and for MC® they were Ra = 2.02 µm. Alamar BlueTM assay LIVE/DEADTM staining results indicated equivalent biological development regarding both cell types for the two implants. Significant enhancement was found for hGF ALP activity in the presence of the two tested implants in a time-dependent manner from day 7 to day 14 (** p < 0.01). Alizarin red staining demonstrated significant calcium deposition enhancement when cells were interfaced with the NB™ compared to the MC® implant (** p < 0.05). Moreover, SEM and confocal imaging revealed good cell adhesion with a denser cellular layer on the MC® than the NB™ surface. The MC® cytocompatibility was ranked as equivalent to the gold standard implant despite the surface properties differences. These findings provide new insights about the minimally invasive implant’s biological behavior and its potential clinical implication in different implantology situations.

Honeycomb-Structured Porous Films from Poly(3-hydroxybutyrate) and Poly(3-hydroxybutyrate-co-3-hydroxyvalerate): Physicochemical Characterization and Mesenchymal Stem Cells Behavior

Surface morphology affects cell attachment and proliferation. In this research, different films made of biodegradable polymers, poly(3-hydroxybutyrate) (PHB) and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHB-co-HV), containing different molecular weights, with microstructured surfaces were investigated. Two methods were used to obtain patterned films—water-assisted self-assembly (“breath figure”) and spin-coating techniques. The water-assisted technique made it possible to obtain porous films with a self-assembled pore structure, which is dependent on the monomer composition of a polymer along with its molecular weight and the technique parameters (distance from the nozzle, volume, and polymer concentration in working solution). Their pore morphologies were evaluated and their hydrophobicity was examined. Mesenchymal stem cells (MSCs) isolated from bone marrow were cultivated on a porous film surface. MSCs’ attachment differed markedly depending on surface morphology. On strip-formed stamp films, MSCs elongated along the structure, however, they interacted with a larger area of film surface. The honeycomb films and column type films did not set the direction of extrusion, but cell flattening depended on structure topography. Thus, stem cells can “feel” the various surface morphologies of self-assembled honeycomb films and change their behavior depending on it.

Assessment of Customized Alveolar Bone Augmentation Using Titanium Scaffolds vs Polyetheretherketone (PEEK) Scaffolds: A Comparative Study Based on 3D Printing Technology

Customized alveolar bone augmentation provides sufficient and precisely regenerated bone tissue for subsequent dental implant placement. Although some clinical cases have confirmed the successful use of the patient-specific polyetheretherketone (PEEK) scaffolds, the biomechanical property and osteogenic performance of the patient-specific PEEK scaffolds remain unclear. The objectives of this study were (1) to evaluate the space maintenance capacity and osteogenic performance of the patient-specific PEEK scaffolds for customized alveolar bone augmentation and (2) to compare the biomechanical properties of three-dimensionally printed titanium scaffolds and PEEK scaffolds. Both titanium scaffolds and PEEK scaffolds were designed and manufactured via additive manufacturing technology combined with computer-aided design (CAD). In three-point bending tests, the bending strength of the PEEK scaffold was about 1/3 that of the titanium scaffold. Accordingly, the equivalent strain value of the internal bone graft beneath the PEEK scaffold was about 3 times that beneath the titanium scaffold in finite element analysis, but the maximum deformations of both scaffolds were less than 0.05 mm. Meanwhile, in in vivo experiments, it is demonstrated that both scaffolds have similar space maintenance capacity and bone ingrowth efficiency. In conclusion, patient-specific PEEK scaffolds showed significantly lower biomechanical strength but comparable space maintenance and osteogenic properties to the titanium counterpart. Compared with traditional guided bone regeneration (GBR) surgery, both patient-specific PEEK and titanium scaffolds can achieve excellent osteogenic space maintenance ability. This study provides a preliminary basis for the clinical translation of the nonmetallic barrier membrane in customized alveolar bone augmentation.

3D Printing of Calcium Phosphate/Calcium Sulfate with Alginate/Cellulose-Based Scaffolds for Bone Regeneration: Multilayer Fabrication and Characterization

Congenital abnormalities, trauma, and disease result in significant demands for bone replacement in the craniofacial region and across the body. Tetra-compositions of organic and inorganic scaffolds could provide advantages for bone regeneration. This research aimed to fabricate and characterize amorphous calcium phosphate (ACP)/calcium sulfate hemihydrate (CSH) with alginate/cellulose composite scaffolds using 3D printing. Alginate/cellulose gels were incorporated with 0%, 13%, 15%, 18%, 20%, and 23% ACP/CSH using the one-pot process to improve morphological, physiochemical, mechanical, and biological properties. SEM displayed multi-staggered filament layers with mean pore sizes from 298 to 377 μm. A profilometer revealed mean surface roughness values from 43 to 62 nm that were not statistically different. A universal test machine displayed the highest compressive strength and modulus with a statistical significance in the 20% CP/CS group. FTIR spectroscopy showed peaks in carbonate, phosphate, and sulfate groups that increased as more ACP/CSH was added. Zero percent of ACP/CSH showed the highest swelling and lowest remaining weight after degradation. The 23% ACP/CSH groups cracked after 60 days. In vitro biocompatibility testing used the mouse osteoblast-like cell line MC3T3-E1. The 18% and 20% ACP/CSH groups showed the highest cell proliferation on days five and seven. The 20% ACP/CSH was most suitable for bone cell regeneration.

Orthopedics-Related Applications of Ultrafast Laser and Its Recent Advances

The potential of ultrafast lasers (pico- to femtosecond) in orthopedics-related procedures has been studied extensively for clinical adoption. As compared to conventional laser systems with continuous wave or longer wave pulse, ultrafast lasers provide advantages such as higher precision and minimal collateral thermal damages. Translation to surgical applications in the clinic has been restrained by limitations of material removal rate and pulse average power, whereas the use in surface texturing of implants has become more refined to greatly improve bioactivation and osteointegration within bone matrices. With recent advances, we review the advantages and limitations of ultrafast lasers, specifically in orthopedic bone ablation as well as bone implant laser texturing, and consider the difficulties encountered within orthopedic surgical applications where ultrafast lasers could provide a benefit. We conclude by proposing our perspectives on applications where ultrafast lasers could be of advantage, specifically due to the non-thermal nature of ablation and control of cutting.

The Role of Surface Chemistry in the Osseointegration of PEEK Implants

Poly(etheretherketone) (PEEK) implants suffer from poor osseointegration because of chronic inflammation. In this study, we hypothesized that adding NH₂ and COOH groups to the surface of PEEK could modulate macrophage responses by altering protein adsorption and improve its osseointegration. NH₂ and COOH-functionalized PEEK surfaces induced pro- and anti-inflammatory macrophage responses, respectively, and differences in protein adsorption patterns on these surfaces were related to the varied inflammatory responses. The macrophage responses to NH₂ surfaces significantly reduced the osteogenic differentiation of mesenchymal stem cells (MSCs). MSCs cultured on NH₂ surfaces differentiated less than those on COOH surfaces even though NH₂ surfaces promoted the most mineralization in simulated body fluid solutions. After 14 days in rat tibia unicortical defects, the bone around NH₂ surfaces had thinner trabeculae and higher specific bone surface than the bone around unmodified implants; surprisingly, the NH₂ implants significantly increased bone-binding over the unmodified implants, while COOH implants only showed a trend for increasing bone-binding. Taken together, these results suggest that both mineral-binding and immune responses play a role in osseointegration, and PEEK implant integration may be improved with mixtures of these two functional groups to harness the ability to reduce inflammation and bind bone strongly.

Mesh Ti6Al4V Material Manufactured by Selective Laser Melting (SLM) as a Promising Intervertebral Fusion Cage

Intervertebral cages made of Ti6Al4V alloy show excellent osteoconductivity, but also higher stiffness, compared to commonly used polyether-ether-ketone (PEEK) materials, that may lead to a stress-shielding effect and implant subsidence. In this study, a metallic intervertebral fusion cage, with improved mechanical behavior, was manufactured by the introduction of a three-dimensional (3D) mesh structure to Ti6Al4V material, using an additive manufacturing method. Then, the mechanical and biological properties of the following were compared: (1) PEEK, with a solid structure, (2) 3D-printed Ti6Al4V, with a solid structure, and (3) 3D-printed Ti6Al4V, with a mesh structure. A load-induced subsidence test demonstrated that the 3D-printed mesh Ti6Al4V cage had significantly lower tendency (by 15%) to subside compared to the PEEK implant. Biological assessment of the samples proved that all tested materials were biocompatible. However, both titanium samples (solid and mesh) were characterized by significantly higher bioactivity, osteoconductivity, and mineralization ability, compared to PEEK. Moreover, osteoblasts revealed stronger adhesion to the surface of the Ti6Al4V samples compared to PEEK material. Thus, it was clearly shown that the 3D-printed mesh Ti6Al4V cage possesses all the features for optimal spinal implant, since it carries low risk of implant subsidence and provides good osseointegration at the bone-implant interface.

Modification of polyetheretherketone (PEEK) physical features to improve osteointegration

Polyetheretherketone (PEEK) has been widely applied in orthopedics because of its excellent mechanical properties, radiolucency, and biocompatibility. However, the bioinertness and poor osteointegration of PEEK have greatly limited its further application. Growing evidence proves that physical factors of implants, including their architecture, surface morphology, stiffness, and mechanical stimulation, matter as much as the composition of their surface chemistry. This review focuses on the multiple strategies for the physical modification of PEEK implants through adjusting their architecture, surface morphology, and stiffness. Many research findings show that transforming the architecture and incorporating reinforcing fillers into PEEK can affect both its mechanical strength and cellular responses. Modified PEEK surfaces at the macro scale and micro/nano scale have positive effects on cell-substrate interactions. More investigations are necessary to reach consensus on the optimal design of PEEK implants and to explore the efficiency of various functional implant surfaces. Soft-tissue integration has been ignored, though evidence shows that physical modifications also improve the adhesion of soft tissue. In the future, ideal PEEK implants should have a desirable topological structure with better surface hydrophilicity and optimum surface chemistry.

Zinc-Doping Induces Evolution of Biocompatible Strontium-Calcium-Phosphate Conversion Coating on Titanium to Improve Antibacterial Property

Implant-associated infections (IAI) remains a common and devastating complication in orthopedic surgery. To reduce the incidence of IAI, implants with intrinsic antibacterial activity have been proposed. The surface functionalization and structure optimization of metallic implants can be achieved by surface modification using the phosphate chemical conversion (PCC) technique. Zinc (Zn) has strong antibacterial behavior toward a broad-spectrum of bacteria. Herein, Zn was incorporated into strontium-calcium-phosphate (SrCaP) coatings on titanium (Ti) via PCC method, and the influence of its doping amount on the phase, microstructure, antibacterial activity, and biocompatibility of the composite coating was researched. The results indicated that traces of Zn doping produced grain refinement of SrCaP coating with no significant effect on its phase and surface properties, while a higher Zn content induced its phase and microstructure transformed into zinc-strontium-phosphate (SrZn₂(PO₄)₂). SrCaP-Zn1 and SrCaP-Zn4 represented trace and high content Zn-doped coatings, respectively, which exhibited a similar bacterial attachment for a short time but showed inhibition of biofilm formation after continuous incubation up to 24 h. The killing rates of SrCaP-Zn1 coating for Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli) reached 61.25% and 55.38%, respectively. While that data increased to 83.01% and 71.28% on SrCaP-Zn4 coating due to the more-releasing Zn²⁺. Furthermore, in vitro culture of MC3T3-E1 cells proved that the Zn-doped coatings also possessed excellent biocompatibility. This study provides a new perception for the phase and microstructural optimization of phosphate coatings on implant surfaces, as well as fabricating promising coatings with excellent biocompatibility and antimicrobial properties against IAI.

Success Factors of Additive Manufactured Root Analogue Implants

Dental implantation is an effective method for the treatment of loose teeth, but the threaded dental implants used in the clinic cannot match with the tooth extraction socket. A root analogue implant (RAI) has the congruence shape, which reduces the damage to bone and soft tissue. Additive manufacturing (AM) technologies have the advantages of high precision, flexibility, and easy operation, becoming the main manufacturing method of RAI in basic research. The purpose of this systematic review is to summarize AM technologies used for RAI manufacturing as well as the factors affecting successful implantation. First, it introduces the AM technologies according to different operating principles and summarizes the advantages and disadvantages of each method. Then the influences of materials, structure design, surface characteristics, implant site, and positioning are discussed, providing reference for designers and dentists. Finally, it addresses the gap between basic research and clinical application for additive manufactured RAIs and discusses the current challenges and future research directions for this field.

High proportion strontium-doped micro-arc oxidation coatings enhance early osseointegration of titanium in osteoporosis by anti-oxidative stress pathway

The excessive accumulation of reactive oxygen species (ROS) under osteoporosis precipitates a microenvironment with high levels of oxidative stress (OS). This could significantly interfere with the bioactivity of conventional titanium implants, impeding their early osseointegration with bone. We have prepared a series of strontium (Sr)-doped titanium implants via micro-arc oxidation (MAO) to verify their efficacy and differences in osteoinduction capabilities under normal and osteoporotic (high OS levels) conditions. Apart from the chemical composition, all groups exhibited similar physicochemical properties (morphology, roughness, crystal structure, and wettability). Among the groups, the low Sr group (Sr25%) was more conducive to osteogenesis under normal conditions. In contrast, by increasing the catalase (CAT)/superoxide dismutase (SOD) activity and decreasing ROS levels, the high Sr-doped samples (Sr75% and Sr100%) were superior to Sr25% in inducing osteogenic differentiation of MC3T3-E1 cells and the M2 phenotype polarization of RAW264.7 cells, thus enhancing early osseointegration. Furthermore, the results of both in vitro cell co-culture and in vivo studies also showed that the high Sr-doped samples (especially Sr100%) had positive effects on osteoimmunomodulation under the OS microenvironment. Ultimately, the collated findings indicated that the high proportion Sr-doped MAO coatings were more favorable for osteoporosis patients in implant restorations.

•

First study on osteogenic difference of Sr-doped implants in normal and OS conditions.

•

Low Sr-doped MAO coating displays optimal bioactivity in normal microenvironment.

•

High Sr coating significantly enhances osteoimmunomodulation/osteoinduction under OS.

•

High Sr sample resists OS damage by activating CAT/SOD and scavenging excess ROS.

•

High Sr implant restorations are more favorable for osteoporosis patients.

Study on the biological behaviors of CaP coatings with different morphology on carbon/carbon composites

In this work, we designed and fabricated a CaP composite bio-coating with different surface morphologies on a carbon/carbon (C/C) matrix by means of hybrid supersonic atmospheric plasma spraying (SAPS) and microwave-hydrothermal (MH) technologies. We found that all studied coating materials can support mesenchymal stem cells (MSCs) proliferation with prolonged culture time (3 days and 7 days) in vitro. Furthermore, according to the (Confocal Laser Scanning Microscopy) CLSM results, the MSCs also showed good attachment and different spreading morphologies on SAPS/MH coatings. As such, C/C matrix, the MH treated coatings with needle-like and rod-like microstructures were chosen for further in vivo investigation. Considering the good bonding between host tissue and the studied materials, the in vivo morphology studies confirmed a good histocompatibility for all coating samples, as well as a decreasing expression for inflammatory factors in a physiological environment. The histological results around the implants indicated different cell aggregation and vascularization ability in the local micro-environment. In particular, based on the reduction of the C/C initial surface flaws (e.g. hydrophobicity, biological inertia and easily producing carbon fragments or particles), the MH treated coating with rod-like surface morphology with a specific surface area (~2.33 m²/g) and roughness (~13.80 μm), showed excellent performance as a promising implant in live tissue.

Polydopamine-decorated black phosphorous to enhance stability in polymer scaffold

Black phosphorous (BP) is recognized as an effective reinforcement for polymer scaffold because of its excellent mechanical property and biocompatibility. Nevertheless, its poor stability in physiological environment limits its application in bone repair. In this work, BP was modified with dopamine by self-polymerization approach (donated as BP@PDA) to improve its stability, and then was introduced into poly-L-lactic acid (PLLA) scaffold fabricated by selective laser sintering technology. Results showed the compressive and tensile strength of PLLA/BP@PDA scaffold were improved by 105% and 50%, respectively. The enhanced strength was ascribed to the increased stability of BP and the improved compatibility of BP@PDA with PLLA matrix after modifying with polydopamine. Simultaneously, the bioactivity of PLLA scaffold was significantly improved. It was attributed to that BP@PDA provided the sustained source ofPO43-ions which could capture Ca²⁺ions from physiological medium to facilitatein situbiomineralization, thereby promoting cell adhesion, proliferation and differentiation. This study demonstrated the great potential of BP@PDA in bone repair.

The Impact of Dental Implant Surface Modifications on Osseointegration and Biofilm Formation

Implant surface design has evolved to meet oral rehabilitation challenges in both healthy and compromised bone. For example, to conquer the most common dental implant-related complications, peri-implantitis, and subsequent implant loss, implant surfaces have been modified to introduce desired properties to a dental implant and thus increase the implant success rate and expand their indications. Until now, a diversity of implant surface modifications, including different physical, chemical, and biological techniques, have been applied to a broad range of materials, such as titanium, zirconia, and polyether ether ketone, to achieve these goals. Ideal modifications enhance the interaction between the implant's surface and its surrounding bone which will facilitate osseointegration while minimizing the bacterial colonization to reduce the risk of biofilm formation. This review article aims to comprehensively discuss currently available implant surface modifications commonly used in implantology in terms of their impact on osseointegration and biofilm formation, which is critical for clinicians to choose the most suitable materials to improve the success and survival of implantation.

An In Vitro Evaluation of the Hierarchical Micro/Nanoporous Structure of a Ti3Zr2Sn3Mo25Nb Alloy after Surface Dealloying

A process to dealloy a Ti-3Zr-2Sn-3Mo-25Nb (TLM) titanium alloy to create a porous surface structure has been reported in this paper aiming to enhance the bioactivity of the alloy. A simple nanoporous topography on the surface was produced through dealloying the as-solution treated TLM alloy. In contrast, dealloying the as-cold rolled alloy created a hierarchical micro/nanoporous topography. SEM and XPS were performed to characterize the topography and element chemistry of both porous structures. The roughness, hydrophilicity, protein adsorption, cell adhesion, proliferation, and osteogenic differentiation were tested. The elements of Zr, Mo, Sn, and Nb were depleted at the nanoporous TLM surface with a diameter of 15.6 ± 2.3 nm. Dissolving the microscale α phase from the alloy surface contributed to the formation of the microscale grooves on the surface. The simple nanoporous topographical surface exhibited hydrophilicity and higher protein adsorption ability, which facilitated the early adhesion of osteoblasts compared with the hierarchical micro/nanoporous surface. On the other hand, the hierarchical micro/nanoporous surface improved cell proliferation and differentiation and still retained the contact guidance function, which implied good bonding for osseointegration. This research revealed the effect of phase composition on the surface morphology of dealloying titanium alloy and the synergistic effect of micron and nanometer topography on the function of osteoblasts. This paper therefore provides insights into the surface topological design of titanium-based biomaterials with improved biocompatibility.

Effects of surface area and topography on 3D printed tricalcium phosphate scaffolds for bone grafting applications

Additive manufacturing (AM), or 3D printing, of bioceramic scaffolds promises personalized treatment options for patients with site-specific designability for repair and reconstruction of bone defects. Although the theory for creating these complex geometries has already been made possible through AM's advancement, such shapes' manufacturability is difficult due to printing with ceramics' inherent complexities. Ceramics have the added challenge of being highly brittle, poor handleability of green (pre-sintered) parts, making complex shape high strength parts challenging to manufacture. This has led to a significant literature gap regarding the feasibility of creating bioceramic scaffolds with unique architectures that can be used in site-specific, individualized patient treatment. This work aims to successfully create complex topographical surfaces of cylindrical bone-like scaffolds to understand the correlation of increasing the scaffold surface area on mechanical properties and in vitro osteoblast cell proliferation. An increase in osteoblast cell proliferation and facilitation in cellular attachment can ultimately lead to improved bone healing. This work explores the printing parameters within an Innovent+® ExOne binder jet 3D printer to produce scaffold designs from synthesized tricalcium phosphate powder. Mechanical testing reveals the designed structures enhance scaffold compressive strength by 30% compared to control dense cylindrical scaffolds. Osteoblast cell proliferation is also increased due to changes in surface topography with a nearly 2-fold increase. Our work incorporates macro-level topographical changes to increase surface area, which is another avenue that could be combined with other scaffold features such as porosity. Results show bulk surface topography modifications via 3D printing can increase surface area to support enhanced biological response without compromising mechanical properties. This discovery may enable a future generation of porous scaffolds with external structures for further progress towards proper defect-specific synthetic bone grafts.

Increased Osteogenic Potential of Pre-Osteoblasts on Three-Dimensional Printed Scaffolds Compared to Porous Scaffolds for Bone Regeneration

Background

One of the main challenges with conventional scaffold fabrication methods is the inability to control scaffold architecture. Recently, scaffolds with controlled shape and architecture have been fabricated using three-dimensional printing (3DP). Herein, we aimed to determine whether the much tighter control of microstructure of 3DP poly(lactic-co-glycolic) acid/β-tricalcium phosphate (PLGA/β-TCP) scaffolds is more effective in promoting osteogenesis than porous scaffolds produced by solvent casting/porogen leaching.

Methods

Physical and mechanical properties of porous and 3DP scaffolds were studied. The response of pre-osteoblasts to the scaffolds was analyzed after 14 days.

Results

TThe 3DP scaffolds had a smoother surface (Ra: 22 ± 3 µm) relative to the highly rough surface of porous scaffolds (Ra: 110 ± 15 µm). Water contact angle was 112 ± 4° on porous and 76 ± 6° on 3DP scaffolds. Porous and 3DP scaffolds had the pore size of 408 ± 90 and 315 ± 17 µm and porosity of 85 ± 5% and 39 ± 7%, respectively. Compressive strength of 3DP scaffolds (4.0 ± 0.3 MPa) was higher than porous scaffolds (1.7 ± 0.2 MPa). Collagenous matrix deposition was similar on both scaffolds. Cells proliferated from day 1 to day 14 by fourfold in porous and by 3.8-fold in 3DP scaffolds. Alkaline phosphatase (ALP) activity was 21-fold higher in 3DP scaffolds than porous scaffolds.

Conclusion

The 3DP scaffolds show enhanced mechanical properties and ALP activity compared to porous scaffolds in vitro, suggesting that 3DP PLGA/β-TCP scaffolds are possibly more favorable for bone formation.

A comparative study on silicon nitride, titanium and polyether ether ketone on mouse pre-osteoblast cells

The current study provides more insights about the surface bioactivity of the silicon nitride (Si₃N₄) as a potential candidate for bone regeneration in craniofacial and orthopaedic applications compared with conventional implantation materials. Current skeletal reconstructive materials such as titanium and polyether ether ketone (PEEK) are limited by poor long-term stability, biocompatibility and prolonged healing. Si₃N₄ is an FDA-approved material for an intervertebral spacer in spinal fusion applications. It is biocompatible and has antimicrobial properties. Here, we hypothesize that Si₃N₄ was found to be an osteoconductive material and conducts the growth, differentiation of MC3T3-E1 cells for extracellular matrix deposition, mineralization and eventual bone regeneration for craniofacial and orthopaedic applications. MC3T3-E1 cells were used to study the osteoblastic differentiation and mineralization on sterile samples of Si₃N₄, titanium alloy and PEEK. The samples were then analysed for extracellular matrix deposition and mineralization by FTIR, Raman spectroscopy, SEM, EDX, Alizarin Red, qRT-PCR and ELISA. The in vitro study indicates the formation of collagen fibres and mineral deposition on all three sample surfaces. There was more profound and faster ECM deposition and mineralization on Si₃N₄ surface as compared to titanium and PEEK. The FTIR and Raman spectroscopy show formation of collagen and mineral deposition at 30 days for Si₃N₄ and titanium and not PEEK. The peaks shown by Raman for Si₃N₄ resemble closely to natural bone. Results also indicate the upregulation of osteogenic transcription factors such as RUNX2, SP7, collagen type I and osteocalcin. The authors concluded that Si₃N₄ rapidly conducts mineralized tissue formation via extracellular matrix deposition and biomarker expression in mouse calvarial pre-osteoblast cells. Thus, this study confirms that the bioactive Si₃N₄ could be a potential material for craniofacial and orthopaedic applications leading to rapid bone regeneration that resemble the natural bone structure.

The Relationship Between Serum Level of Vitamin D3 and Osseointegration Around the Dental Implant

At present, dental implants are used more than before, and their high success rate is attributed to sufficient osseointegration, which depends on prosthetic-, implant-, and patient-related factors. The quality and quantity of bone and the host response are the main patient-related factors. Vitamin D3 affects bone metabolism by stimulating both osteoclasts and osteoblasts. This study aimed to review the human studies on the efficacy of vitamin D3 for dental implant osseointegration. Search of the literature yielded only 4 studies on human models, of which 2 showed the optimal efficacy of vitamin D3 for dental implant osseointegration, whereas the remaining 2 did not report any positive effect. However, this finding may be related to the small sample size of the vitamin D3-deficient group, which can compromise statistical analyses. In conclusion, vitamin D3 seems to be effective for dental implant osseointegration, although further research is required on human models.

Bioinspired Modifications of PEEK Implants for Bone Tissue Engineering

In recent years, polyetheretherketone (PEEK) has been increasingly employed as an implant material in clinical applications. Although PEEK is biocompatible, chemically stable, and radiolucent and has an elastic modulus similar to that of natural bone, it suffers from poor integration with surrounding bone tissue after implantation. To improve the bioactivity of PEEK, numerous strategies for functionalizing the PEEK surface and changing the PEEK structure have been proposed. Inspired by the components, structure, and function of bone tissue, this review discusses strategies to enhance the biocompatibility of PEEK implants and provides direction for fabricating multifunctional implants in the future.

Mesoporous silica pellets as bifunctional bone drug delivery system for cefazolin

For decades, bone drug delivery systems dedicated for osteomyelitis treatment have been investigated as bifunctional materials that exhibit prolonged drug release and mineralization potential. Herein, composite-type pellets based on cefazolin-loaded amino-modified mesoporous silica SBA-15 and microwave-assisted hydroxyapatite were investigated as potential bone drug delivery system in vitro. Pellets were obtained by granulation, extrusion and spheronization methods in laboratory scale and studied in terms of physical properties, drug release, mineralization potential, antimicrobial activity and cytotoxicity towards human osteoblasts. The obtained pellets were characterized for hardness and friability which indicated the pellets durability during further investigations. Prolonged (5-day) release of cefazolin from pellets was observed. The pellets exhibited mineralization potential in simulated body fluid, i.e., a continuous layer of bone-like apatite was formed on the surface of pellets after 28 days of incubation. An antimicrobial assay of pellets revealed an antibacterial effect against Staphylococcus aureus strain during 6 days. No cytotoxic effects of pellets towards human osteoblasts were observed. The obtained results proved that proposed pellets appear to have potential applications as bone drug delivery systems.

Mineral Distribution Spatially Patterns Bone Marrow Stromal Cell Behavior on Monolithic Bone Scaffolds

Interfaces between soft tissue and bone are characterized by transitional gradients in composition and structure that mediate substantial changes in mechanical properties. For interfacial tissue engineering, scaffolds with mineral gradients have shown promise in controlling osteogenic behavior of seeded bone marrow stromal cells (bMSCs). Previously, we have demonstrated a 'top-down' method for creating monolithic bone-derived scaffolds with patterned mineral distributions similar to native tissue. In the present work, we evaluated the ability of these scaffolds to pattern osteogenic behavior in bMSCs in basic, osteogenic, and chondrogenic biochemical environments. Immunohistochemical (IHC) and histological stains were used to characterize cellular behavior as a function of local mineral content. Alkaline phosphatase, an early marker of osteogenesis, and osteocalcin, a late marker of osteogenesis, were positively correlated with mineral content in basic, osteogenic, and chondrogenic media. The difference in bMSC behavior between the mineralized and demineralized regions was most pronounced in an basic biochemical environment. In the mineralized regions of the scaffold, osteogenic markers were clearly present as early as 4 days in culture. In osteogenic media, osteogenic behavior was observed across the entire scaffold, whereas in chondrogenic media, there was an overall reduction in osteogenic biomarkers. Overall, these results indicate local mineral content of the scaffold plays a key role in spatially patterning bMSC behavior. Our results can be utilized for the development of interfacial tissue engineered scaffolds and understanding the role of local environment in determining bMSC behavior. STATEMENT OF SIGNIFICANCE: Soft tissue-to-bone interfaces, such as tendon-bone, ligament-bone, and cartilage-bone, are ubiquitous in mammalian musculoskeletal systems. These interfacial tissues have distinct, hierarchically-structured gradients of cellular, biochemical, and materials components. Given the complexity of the biological structures, interfacial tissues present unique challenges for tissue engineering. Here, we demonstrate that material-derived cues can spatially pattern osteogenic behavior in bone marrow stromal cells (bMSCs). Specifically, we observed that when the bMSCs are cultured on bone-derived scaffolds with mineral gradients, cells in contact with higher mineral content display osteogenic behavior at earlier times than those on the unmineralized substrate. The ability to pattern the cellular complexity found in native interfaces while maintaining biologically relevant structures is a key step towards creating engineered tissue interfaces.

Gaseous sulfur trioxide induced controllable sulfonation promoting biomineralization and osseointegration of polyetheretherketone implants

Fabricating a desired porous structure on the surface of biomedical polyetheretherketone (PEEK) implants for enhancing biological functions is crucial and difficult due to its inherent chemical inertness. In this study, a porous surface of PEEK implants was fabricated by controllable sulfonation using gaseous sulfur trioxide (SO₃) for different time (5, 15, 30, 60 and 90 min). Micro-topological structure was generated on the surface of sulfonated PEEK implants preserving original mechanical properties. The protein absorption capacity and apatite forming ability was thus improved by the morphological and elemental change with higher degree of sulfonation. In combination of the appropriate micromorphology and bioactive sulfonate components, the cell adhesion, migration, proliferation and extracellular matrix secretion were obviously enhanced by the SPEEK-15 samples which were sulfonated for 15 min. Finding from this study revealed that controllable sulfonation by gaseous SO₃ would be an extraordinarily strategy for improving osseointegration of PEEK implants by adjusting the microstructure and chemical composition while maintaining excellent mechanical properties.

In vitro and in vivo study on the osseointegration of BCP-coated versus uncoated nondegradable thermoplastic polyurethane focal knee resurfacing implants

Focal knee resurfacing implants (FKRIs) are intended to treat cartilage defects in middle-aged patients. Most FKRIs are metal-based, which hampers follow-up of the joint using magnetic resonance imaging and potentially leads to damage of the opposing cartilage. The purpose of this study was to develop a nondegradable thermoplastic polyurethane (TPU) FKRI and investigate its osseointegration. Different surface roughness modifications and biphasic calcium phosphate (BCP) coating densities were first tested in vitro on TPU discs. The in vivo osseointegration of BCP-coated TPU implants was subsequently compared to uncoated TPU implants and the titanium bottom layer of metal control implants in a caprine model. Implants were implanted bilaterally in stifle joints and animals were followed for 12 weeks, after which the bone-to-implant contact area (BIC) was assessed. Additionally, 18F-sodium-fluoride (18F-NaF) positron emission tomography PET/CT-scans were obtained at 3 and 12 weeks to visualize the bone metabolism over time. The BIC was significantly higher for the BCP-coated TPU implants compared to the uncoated TPU implants (p = .03), and did not significantly differ from titanium (p = .68). Similar 18F-NaF tracer uptake patterns were observed between 3 and 12 weeks for the BCP-coated TPU and titanium implants, but not for the uncoated implants. TPU FKRIs with surface modifications could provide the answer to the drawbacks of metal FKRIs.

Functionalized Graphene Nanoparticles Induce Human Mesenchymal Stem Cells to Express Distinct Extracellular Matrix Proteins Mediating Osteogenesis

PURPOSE

The extracellular matrix (ECM) labyrinthine network secreted by mesenchymal stem cells (MSCs) provides a microenvironment that enhances cell adherence, proliferation, viability, and differentiation. The potential of graphene-based nanomaterials to mimic a tissue-specific ECM has been recognized in designing bone tissue engineering scaffolds. In this study, we investigated the expression of specific ECM proteins when human fat-derived adult MSCs adhered and underwent osteogenic differentiation in the presence of functionalized graphene nanoparticles.

METHODS

Graphene nanoparticles with 6-10% oxygen content were prepared and characterized by XPS, FTIR, AFM and Raman spectroscopy. Calcein-am and crystal violet staining were performed to evaluate viability and proliferation of human fat-derived MSCs on graphene nanoparticles. Alizarin red staining and quantitation were used to determine the effect of graphene nanoparticles on osteogenic differentiation. Finally, immunofluorescence assays were used to investigate the expression of ECM proteins during cell adhesion and osteogenic differentiation.

RESULTS

Our data show that in the presence of graphene, MSCs express specific integrin heterodimers and exhibit a distinct pattern of the corresponding bone-specific ECM proteins, primarily fibronectin, collagen I and vitronectin. Furthermore, MSCs undergo osteogenic differentiation spontaneously without any chemical induction, suggesting that the physicochemical properties of graphene nanoparticles might trigger the expression of bone-specific ECM.

CONCLUSION

Understanding the cell-graphene interactions resulting in an osteogenic niche for MSCs will significantly improve the application of graphene nanoparticles in bone repair and regeneration.

3D Titania Nanofiber-Like Webs Induced by Plasma Ionization: A New Direction for Bioreactivity and Osteoinductivity Enhancement of Biomaterials

In this study, we describe the formation method of web-like three-dimensional (3-D) titania nanofibrous structures coated on transparent substrate via a high intensity laser induced reverse transfer (HILIRT) process. First, we demonstrate the mechanism of ablation and deposition of Ti on the glass substrates using multiple picosecond laser pulses at ambient air in an explicit analytical form and compare the theoretical results with the experimental results of generated nanofibers. We then examine the performance of the developed glass samples coated by titania nanofibrous structures at varied laser pulse durations by electron microscopy and characterization methods. We follow this by exploring the response of human bone-derived mesenchymal stem cells (BMSCs) with the specimens, using a wide range of in-vitro analyses including MTS assay (colorimetric method for assessing cell metabolic activity), immunocytochemistry, mineralization, ion release examination, gene expression analysis, and protein adsorption and absorption analysis. Our results from the quantitative and qualitative analyses show a significant biocompatibility improvement in the laser treated samples compared to untreated substrates. By decreasing the pulse duration, more titania nanofibers with denser structures can be generated during the HILIRT technique. The findings also suggest that the density of nanostructures and concentration of coated nanofibers play critical roles in the bioreactivity properties of the treated samples, which results in early osteogenic differentiation of BMSCs.

Assessment of the Inner Surface Microstructure of Decellularized Cortical Bone by a Scanning Electron Microscope

The microstructural changes of bones, which form a hierarchy of skeletal tissue, vary, depending on their condition, and are affected by the behaviors of bone cells. The purpose of this study is to assess the microstructural changes in the inner femoral surface of Sprague Dawley rats according to the conditions using a scanning electron microscope. Microstructural differences on the endocortical surface were observed in the characteristics of osteocytic canaliculi, bone fibers, and surface roughness, showing a rougher surface in old adults and an osteoporosis model by quantitative comparison. These results could be helpful for developing a basic understanding of the microstructural changes that occur on the bone surface under various conditions.

Reduced graphene oxide: osteogenic potential for bone tissue engineering

Collagen (Col) type I, as the major component of the bone extracellular matrix has been broadly studied for bone tissue engineering. However,inferior mechanical properties limit its usage for load bearing applications. In this research, freeze dried Col scaffolds are coated with graphene oxide (GO) through a covalent bond of the amine Col with the graphene carboxyl groups. The prepared scaffolds were then reduced using a chemical agent. Scanning electron microscopy exhibited a porous structure for the synthesized scaffolds with an approximate pore size of 100-220 ± 12 µm, which is in the suitable range for bone tissue engineering application. Reducing the GO coating improved the compressive modulus of the Col from 250 to 970 kPa. Apatite formation was also indicated by immersing the scaffolds in simulated body fluid after five days. The cytocompatibility of the scaffolds, using human bone marrow-derived mesenchymal stem cells, was confirmed with MTT analysis. Alkaline phosphatase assay revealed that reducing the Col-GO scaffolds can effectively activate the differentiation of hBM-MSCs into osteoblasts after 14 days, even without the addition of an osteogenic differentiation medium. The results of this study highlight that GO and its reduced form have considerable potential as bone substitutes for orthopaedic and dental applications.

An In Vitro Study of Osteoblast Response on Fused-Filament Fabrication 3D Printed PEEK for Dental and Cranio-Maxillofacial Implants

Polyetheretherketone (PEEK) is a prime candidate to replace metallic implants and prostheses in orthopedic, spine and cranio-maxillofacial surgeries. Fused-filament fabrication (FFF) is an economical and efficient three-dimensional (3D) printing method to fabricate PEEK implants. However, studies pertaining to the bioactivity of FFF 3D printed PEEK are still lacking. In this study, FFF 3D printed PEEK samples were fabricated and modified with polishing and grit-blasting (three alumina sizes: 50, 120, and 250 µm) to achieve varying levels of surface roughness. In vitro cellular response of a human osteosarcoma cell line (SAOS-2 osteoblasts, cell adhesion, metabolic activity, and proliferation) on different sample surfaces of untreated, polished, and grit-blasted PEEK were evaluated. The results revealed that the initial cell adhesion on different sample surfaces was similar. However, after 5 days the untreated FFF 3D printed PEEK surfaces exhibited a significant increase in cell metabolic activity and proliferation with a higher density of osteoblasts compared with the polished and grit-blasted groups (p < 0.05). Therefore, untreated FFF 3D printed PEEK with high surface roughness and optimal printing structures might have great potential as an appropriate alloplastic biomaterial for reconstructive cranio-maxillofacial surgeries.

Silicon nitride enhances osteoprogenitor cell growth and differentiation via increased surface energy and formation of amide and nanocrystalline HA for craniofacial reconstruction

The bioactive silicon nitride (Si₃N₄) has been FDA cleared for use as spinal intervertebral arthrodesis devices. Because its surface properties promote bone ongrowth and ingrowth, it also has the potential to benefit craniofacial reconstruction. Thus, the aim of this work was to determine whether the surface properties of Si₃N₄ could enhance the osteoblast cell growth, differentiation and nucleation of hydroxyapatite (HA) crystals compared to conventional implant materials such as titanium (Ti) and polyether ether ketone (PEEK). X-ray absorbance near-edge structure analysis (XANES) indicated the presence of Si-Si, Si-O and Si-N bonding. Surface wettability studies confirmed that Si₃N₄ exhibits the lowest contact angle and highest surface energy. Cell culture studies showed that osteoblast growth was enhanced on Si₃N₄ after 1 day and up to 7 days. Si₃N₄ surface induced highest surface coverage and thickness of nanocrystalline HA (211) and (203) in cell-free in vitro studies after 7 days of culture. Raman spectroscopy analysis confirmed the presence of surface functional groups consisting of phosphate and carbonate species. Interestingly, Si₃N₄ surface showed amide and hydroxyproline groups, the precursors to collagen, which were not observed on Ti and PEEK surfaces. Furthermore, Si₃N₄ surface indicated high expression of RUNX2, enhanced cell differentiation and dense collagenous ECM after 30 days of the in vitro study. The present study concluded that Si₃N₄ surface enhances osteoprogenitor cell adhesion, growth, RUNX2 expression and ECM formation via the coupled effects of higher surface energy and the presence of amide and nanocrystalline HA functional groups.

Carbon Fiber Reinforced PEEK Composites Based on 3D-Printing Technology for Orthopedic and Dental Applications

Fused deposition modeling (FDM) is a rapidly growing three-dimensional (3D) printing technology and has great potential in medicine. Polyether-ether-ketone (PEEK) is a biocompatible high-performance polymer, which is suitable to be used as an orthopedic/dental implant material. However, the mechanical properties and biocompatibility of FDM-printed PEEK and its composites are still not clear. In this study, FDM-printed pure PEEK and carbon fiber reinforced PEEK (CFR-PEEK) composite were successfully fabricated by FDM and characterized by mechanical tests. Moreover, the sample surfaces were modified with polishing and sandblasting methods to analyze the influence of surface roughness and topography on general biocompatibility (cytotoxicity) and cell adhesion. The results indicated that the printed CFR-PEEK samples had significantly higher general mechanical strengths than the printed pure PEEK (even though there was no statistical difference in compressive strength). Both PEEK and CFR-PEEK materials showed good biocompatibility with and without surface modification. Cell densities on the "as-printed" PEEK and the CFR-PEEK sample surfaces were significantly higher than on the corresponding polished and sandblasted samples. Therefore, the FDM-printed CFR-PEEK composite with proper mechanical strengths has potential as a biomaterial for bone grafting and tissue engineering applications.

Biological Response to Carbon-Family Nanomaterials: Interactions at the Nano-Bio Interface

During the last few decades, several studies have suggested that carbon-based nanomaterials, owing to their unique properties, could act as promising candidates in biomedical engineering application. Wide-ranging research efforts have investigated the cellular and molecular responses to carbon-based nanomaterials at the nano-bio interfaces. In addition, a number of surface functionalization strategies have been introduced to improve their safety profile in the biological environment. The present review discusses the general principles of immunological responses to nanomaterials. Then, it explains essential physico-chemical properties of carbon-familynanomaterials, including carbon nanotubes (CNTs), graphene, fullerene, carbon quantum dots (CDs), diamond-like carbon (DLC), and mesoporous carbon biomaterials (MCNs), which significantly affect the immunological cellular and molecular responses at the nano-bio interface. The discussions also briefly highlight the recent studies that critically investigated the cellular and molecular responses to various carbon-based nanomaterials. It is expected that the most recent perspective strategies for improving the biological responses to carbon-based nanomaterials can revolutionize their functions in emerging biological applications.

Collagen Functionalized With Graphene Oxide Enhanced Biomimetic Mineralization and in Situ Bone Defect Repair

Biomimetic mineralization using simulated body fluid (SBF) can form a bonelike apatite (Ap) on the natural polymers and enhance osteoconductivity and biocompatibility, and reduce immunological rejection. Nevertheless, the coating efficiency of the bonelike apatite layer on natural polymers still needs to be improved. Graphene oxide (GO) is rich in functional groups, such as carbonyls (-COOH) and hydroxyls (-OH), which can provide more active sites for biomimetic mineralization and improve the proliferation of the rat bone marrow stromal cells (r-BMSCs). In this study, we introduced 0%, 0.05%, 0.1%, and 0.2% w/v concentrations of GO into collagen (Col) scaffolds and immersed the fabricated scaffolds into SBF for 1, 7, and 14 days. In vitro environment scanning electron microscopy (ESEM), energy-dispersive spectrometry (EDS), thermogravimetric analysis (TGA), micro-CT, calcium quantitative analysis, and cellular analysis were used to evaluate the formation of bonelike apatite on the scaffolds. In vivo implantation of the scaffolds into the rat cranial defect was used to analyze the bone regeneration ability. The resulting GO-Col-Ap scaffolds exhibited a porous and interconnected structure coated with a homogeneous distribution of bonelike apatite on their surfaces. The Ca/P ratio of 0.1% GO-Col-Ap group was equal to that of natural bone tissue on the basis of EDS analysis. More apatites were observed in the 0.1% GO-Col-Ap group through TGA analysis, micro-CT evaluation, and calcium quantitative analysis. Furthermore, the 0.1% GO-Col-Ap group showed significantly higher r-BMSCs adhesion and proliferation in vitro and more than 2-fold higher bone formation than the Col-Ap group in vivo. Our study provides a new approach of introducing graphene oxide into bone tissue engineering scaffolds to enhance biomimetic mineralization.

Fabrication, multi-scale characterization and in-vitro evaluation of porous hybrid bioactive glass polymer-coated scaffolds for bone tissue engineering

Bioactive glass-based scaffolds are commonly used in bone tissue engineering due to their biocompatibility, mechanical strength and adequate porous structure. However, their hydrophobicity and brittleness limits their practical application. In this study, to improve nanomechanical properties of such scaffolds, pure bioactive hybrid glass and two bioactive hybrid glass-polymer coated composites were fabricated. A complementary micro and nanoscale characterization techniques (SEM, AFM, μCT, FTIR, compressive test, goniometer) were implemented for detailed description of architecture and physicochemical properties of hybrid bioactive glass-based scaffolds with emphasis on nano-mechanics. The final step was in-vitro evaluation of three dimensional macroporous structures. Our findings show that after polymer addition, architecture, topography and surface properties of the scaffolds were changed and promoted favoured behaviour of the cells.

Enhancement of surface bioactivity on carbon fiber-reinforced polyether ether ketone via graphene modification

Background and objective

The modulus of carbon fiber-reinforced polyether ether ketone (CFR-PEEK), a composite containing layers of carbon fiber sheets, can be precisely controlled to match bone. However, CFR-PEEK is biologically inert and cannot promote bone apposition. The objective of this study was to investigate whether graphene modification could enhance the bioactivity of CFR-PEEK.

Methods and results

In vitro, the proliferation and differentiation of rat bone marrow stromal cells on scaffolds were quantified via cell-counting kit-8 assay and Western blotting analysis of osteoblast-specific proteins. Graphene modification significantly promoted bone marrow stromal cell proliferation and accelerated induced differentiation into osteogenic lineages compared to cells seeded onto nongraphene-coated CFR-PEEK. An in vivo rabbit extraarticular graft-to-bone healing model was established. At 4, 8, and 12 weeks after surgery, microcomputed tomography analyses and histological observations revealed significantly better microstructural parameters and higher average mineral apposition rates for graphene-modified CFR-PEEK implants than CFR-PEEK implants (P<0.05). van Gieson staining indicated more new bone was formed around graphene-modified CFR-PEEK implants than CFR-PEEK implants.

Conclusion

Graphene may have considerable potential to enhance the bioactivity and osseointegration of CFR-PEEK implants for clinical applications.

Response of hPDLSCs on 3D printed PCL/PLGA composite scaffolds in vitro

Three-dimensional printed (3DP) scaffolds have become an excellent resource in alveolar bone regeneration. However, selecting suitable printable materials remains a challenge. In the present study, 3DP scaffolds were fabricated using three different ratios of poly (ε-caprolactone) (PCL) and poly-lactic-co-glycolic acid (PLGA), which were 0.1PCL/0.9PLGA, 0.5PCL/0.5PLGA and 0.9PCL/0.1PLGA. The surface characteristics and degradative properties of the scaffolds, and the response of human periodontal ligament stem cells (hPDLSCs) on the scaffolds, were assessed to examine the preferable ratio of PCL and PLGA for alveolar bone regeneration. The results demonstrated that the increased proportion of PLGA markedly accelerated the degradation, smoothed the surface and increased the wettability of the hybrid scaffold. Furthermore, the flow cytometry and Cell Counting Kit-8 assay revealed that the adhesion and proliferation of hPDLSCs were markedlyincreased on the 0.5PCL/0.5PLGA and 0.1PCL/0.9PLGA scaffolds. Additionally, the alkaline phosphatase activity detection and reverse-transcription quantitative polymerase chain reaction demonstrated that the hPDLSCs on the 0.5PCL/0.5PLGA scaffold exhibited the best osteogenic capacity. Consequently, PCL/PLGA composite scaffolds may represent a candidate focus for future bone regeneration studies, and the 0.5PCL/0.5PLGA scaffold demonstrated the best bio-response from the hPDLSCs.

Effect of microporosity on scaffolds for bone tissue engineering

Microporosity has a critical role in improving the osteogenesis of scaffolds for bone tissue engineering. Although the exact mechanism, by which it promotes new bone formation, is not well recognized yet, the related hypothesis can be found in many previous studies. This review presents those possible mechanisms about how the microporosity enhances the osteogenic-related functions of cells in vitro and the osteogenic activity of scaffolds in vivo. In summary, the increased specific surface areas by microporosity can offer more protein adsorption sites and accelerate the release of degradation products, which facilitate the interactions between scaffolds and cells. Meanwhile, the unique surface properties of microporous scaffolds have a considerable effect on the protein adsorption. Moreover, capillary force generated by the microporosity can improve the attachment of bone-related cells on the scaffolds surface, and even make the cells achieve penetration into the micropores smaller than them. This review also pays attention to the relationship between the biological and mechanical properties of microporous scaffolds. Although lots of achievements have been obtained, there is still a lot of work to do, some of which has been proposed in the conclusions and perspectives part.