Nano-engineered Adsorbent for the Removal of Dyes from Water: A Review

Electricity generation and real oily wastewater treatment by Pseudomonas citronellolis 620C in a microbial fuel cell: pyocyanin production as electron shuttle

In the present study, the potential of Pseudomonas citronellolis 620C strain was evaluated, for the first time, to generate electricity in a standard, double chamber microbial fuel cell (MFC), with oily wastewater (OW) being the fuel at 43.625 mg/L initial chemical oxygen demand (COD). Both electrochemical and physicochemical results suggested that this P. citronellolis strain utilized efficiently the OW substrate and generated electricity in the MFC setup reaching 0.05 mW/m2 maximum power. COD removal was remarkable reaching 83.6 ± 0.1%, while qualitative and quantitative gas chromatography/mass spectrometry (GC/MS) analysis of the OW total petroleum and polycyclic aromatic hydrocarbons, and fatty acids revealed high degradation capacity. It was also determined that P. citronellolis 620C produced pyocyanin as electron shuttle in the anodic MFC chamber. To the authors' best knowledge, this is the first study showing (phenazine-based) pyocyanin production from a species other than P. aeruginosa and, also, the first time that P. citronellolis 620C has been shown to produce electricity in a MFC. The production of pyocyanin, in combination with the formation of biofilm in the MFC anode, as observed with scanning electron microscopy (SEM) analysis, makes this P. citronellolis strain an attractive and promising candidate for wider MFC applications.

One-step fabrication of millimeter-scale hollow vesicles with chitosan /DADMAC/ sodium alginate graft copolymer for enhanced anionic dye adsorption

Hollow vesicles are promising in water treatment due to their unique structure of the membrane and inner cavity. However, the adsorption capacity needs to be improved for targeted pollutants. Herein, millimeter-scale hollow vesicles were prepared with a one-step process of sequential stirring and grafting using chitosan, diallyldimethylammonium chloride, and sodium alginate as raw materials with the purpose of efficient removal of anionic dyes from wastewater. The composite vesicles were characterized using scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and X-ray diffraction. The hollow vesicles showed the structure of the cationic membrane and the inner cavity, facilitating the dye adsorption. The adsorption capacity for the anionic dye Reactive Black 5 reached 698.1 mg/g, more than twice that of the binary composite vesicles without graft. The adsorption kinetics and isotherm data coincided with the pseudo-second-order and Langmuir models, respectively, and the adsorption mechanism was monolayer chemisorption. Moreover, the vesicles worked well in wide ranges of environment pH, temperature, and co-existing pollutants. They also possessed excellent cyclic regeneration performance, in which 93 % of the initial adsorption capacity was maintained after four cycles. These results indicate that the millimeter-scale hollow vesicles exhibit broad application prospects for wastewater purification.

Strategies for mitigation of pesticides from the environment through alternative approaches: A review of recent developments and future prospects

Chemical-based peticides are having negative impacts on both the healths of human beings and plants as well. The World Health Organisation (WHO), reported that each year, >25 million individuals in poor nations are having acute pesticide poisoning cases along with 20,000 fatal injuries at global level. Normally, only ∼0.1% of the pesticide reaches to the intended targets, and rest amount is expected to come into the food chain/environment for a longer period of time. Therefore, it is crucial to reduce the amounts of pesticides present in the soil. Physical or chemical treatments are either expensive or incapable to do so. Hence, pesticide detoxification can be achieved through bioremediation/biotechnologies, including nano-based methodologies, integrated approaches etc. These are relatively affordable, efficient and environmentally sound methods. Therefore, alternate strategies like as advanced biotechnological tools like as CRISPR Cas system, RNAi and genetic engineering for development of insects and pest resistant plants which are directly involved in the development of disease- and pest-resistant plants and indirectly reduce the use of pesticides. Omics tools and multi omics approaches like metagenomics, genomics, transcriptomics, proteomics, and metabolomics for the efficient functional gene mining and their validation for bioremediation of pesticides also discussed from the literatures. Overall, the review focuses on the most recent advancements in bioremediation methods to lessen the effects of pesticides along with the role of microorganisms in pesticides elimination. Further, pesticide detection is also a big challenge which can be done by using HPLC, GC, SERS, and LSPR ELISA etc. which have also been described in this review.

Carbon dots as potential candidate for photocatalytic treatment of dye wastewater

Water is the utmost important element for the existence of life. In recent decades, water resources have become highly contaminated by a variety of pollutants, especially toxic dyes that are harmful to both living beings and environment. Hence, there is an urgent need to develop more effective methods than traditional wastewater treatment approaches for treatment of hazardous dyes. Herein, we have addressed the various aspects related to the effective and economically feasible method for photocatalytic degradation of these dyes employing carbon dots. The photocatalysts based on carbon dots including those mediated from biomass have many superiorities over conventional methods such as utilization of economically affordable, non-toxic, rapid reactions, and simple post-processing steps. The current study will also facilitate better insight into the understanding of photocatalytic treatment of dye-polluted wastewater for future wastewater treatment studies. Additionally, the possible mechanistic pathways of photocatalytic dye decontamination, several challenges, and future perspectives have also been summarized.

Photocatalytic Degradation Studies of Organic Dyes over Novel Cu/Ni Loaded Reduced Graphene Oxide Hybrid Nanocomposite: Adsorption, Kinetics and Thermodynamic Studies

Nowadays, for environmental remediation, photocatalytic process involving graphene-based semiconductors is considered a very promising oxidation process for water treatment. In the present study, nanocomposite (Cu/Ni/rGO) has been synthesized by Dypsis lutescens leaf extract. Characterization of the sample was carried out by UV-visible spectroscopy, scanning electron microscopy (SEM), energy dispersive X-ray (EDX) analysis, Fourier transform infrared spectroscopy (FTIR), and X-ray diffraction (XRD). Different parameters like contact time, nanocatalyst amount, dye concentration, effect of temperature. and pH factor were optimized to examine the maximum removal efficiency for dyes rhodamine B and alizarine R with and without visible light source. In both cases, i.e., with or without light, maximum removal was observed at 20 mg of nanocatalyst for 5 ppm concentration of both dyes at 45 °C temperature and pH 10 for rhodamine B and pH 4 for alizarine R, respectively with a 20 min contact time. Maximum removal of dyes 93% rhodamine B and 91% alizarine R were observed under a tungsten lamp as compared to without a tungsten lamp, i.e., 78% of RhB and 75% of AR from mixture solution of these dyes. To assess the rate of reaction, spontaneity, and nature of reaction thermodynamics, kinetics and adsorption isotherms were studied. Thermodynamic values indicated that both dyes depicted endothermic and spontaneous degradation processes. Isotherm data fitted best to a Freundlich isotherm, while results of kinetic studies of both dyes followed the pseudo 2nd order kinetic equation. In the end, scavenging radical studies concluded that hydroxyl radicals were the main active specie involved in the photocatalytic degradation process, and regeneration experiments resulted that Cu/Ni/rGO nanocomposites were re-utilized for about four times.

KMnO4-oxidized whole pine needle based adsorbent for selective and efficient removal of cationic dyes

In the present study, we report the chemical modification of the dried and fallen pine needles (PNs) via a simple protocol using KMnO4 oxidation. The oxidized PNs (OPNs) were evaluated as adsorbents using some cationic and anionic dyes. The successful synthesis of OPNs adsorbent was characterized by various techniques to ascertain its structural attributes. The adsorbent showed selectivity for the cationic dyes with 96.11% removal (Pr) for malachite green (MG) and 89.68% Pr for methylene blue (MB) in 120 min. Kinetic models namely, pseudo-first order, pseudo-second order, and Elovich were applied to have insight into adsorption. Additionally, three adsorption isotherms, i.e., Langmuir, Freundlich, and Temkin were also applied. The dye adsorption followed a pseudo-second-order kinetic model with R2 > 0.99912 for MG and R2 > 0.9998 for MB. The adsorbent followed the Langmuir model with a maximum adsorption capacity (qm) of 223.2 mg/g and 156.9 mg/g for MG and MB, respectively. Furthermore, the OPNs showed remarkable regeneration and recyclability up to nine adsorption-desorption cycles with appreciable adsorption for both the dyes. The use of OPNs as an adsorbent for the removal of dyes from wastewater, therefore, provides an ecologically benign, low-cost, and sustainable solution.

Pseudomonas aeruginosa's greenish-blue pigment pyocyanin: its production and biological activities

A subject of great interest is the bioprospecting of microorganisms and their bioactive byproducts, such as pigments. Microbial pigments have various benefits, including being safe to use due to their natural makeup, having therapeutic effects, and being produced all year round, regardless of the weather or location. Pseudomonas aeruginosa produces phenazine pigments that are crucial for interactions between Pseudomonas species and other living things. Pyocyanin pigment, which is synthesized by 90-95% of P. aeruginosa, has potent antibacterial, antioxidant, and anticancer properties. Herein, we will concentrate on the production and extraction of pyocyanin pigment and its biological use in different areas of biotechnology, engineering, and biology.

Nanotechnology as an efficient and effective alternative for wastewater treatment: an overview

The increase in the surface and groundwater contamination due to global population growth, industrialization, proliferation of pathogens, emerging pollutants, heavy metals, and scarcity of drinking water represents a critical problem. Because of this problem, particular emphasis will be placed on wastewater recycling. Conventional wastewater treatment methods may be limited due to high investment costs or, in some cases, poor treatment efficiency. To address these issues, it is necessary to continuously evaluate novel technologies that complement and improve these traditional wastewater treatment processes. In this regard, technologies based on nanomaterials are also being studied. These technologies improve wastewater management and constitute one of the main focuses of nanotechnology. The following review describes wastewater's primary biological, organic, and inorganic contaminants. Subsequently, it focuses on the potential of different nanomaterials (metal oxides, carbon-based nanomaterials, cellulose-based nanomaterials), membrane, and nanobioremediation processes for wastewater treatment. The above is evident from the review of various publications. However, nanomaterials' cost, toxicity, and biodegradability need to be addressed before their commercial distribution and scale-up. The development of nanomaterials and nanoproducts must be sustainable and safe throughout the nanoproduct life cycle to meet the requirements of the circular economy.

A Comparative Study of Mechanism and Performance of Anionic and Cationic Dialdehyde Nanocelluloses for Dye Adsorption and Separation

In this study, anionic dialdehyde cellulose (DAC) and cationic dialdehyde cellulose (c-DAC) nanofibrous adsorbents were prepared via a two-step reaction from bamboo pulp, using sodium periodate and Girard's reagent T as oxidizing and cationizing agents, respectively. The performance of DAC and c-DAC for selective dye adsorption and separation was evaluated by six different organic dyes (with varying charge properties) and certain binary mixtures. Both adsorbents could remove the dyes but with different capability, where DAC exhibited high adsorption efficiency against cationic dyes (e.g., the maximum adsorption capacity for Bismarck brown Y was 552.1 mg/g) and c-DAC exhibited high adsorption efficiency against anionic dyes (e.g., the maximum adsorption capacity for Congo red was 540.3 mg/g). To investigate the adsorption mechanism for these adsorbents, effects of contact time, initial pH value, initial dye concentration, and ionic strength on the adsorption activity against Congo red were investigated. The adsorption equilibrium data of DAC were found to fit best with the Langmuir isotherm model, whereas that of c-DAC were found to fit best with the Freundlich model. Both DAC and c-DAC adsorption kinetic data could be described by the pseudo-second-order kinetic model, and these adsorbents possessed stable adsorption efficiency in the pH range of 4-10. Furthermore, their dye adsorption capabilities were found to increase with increasing ionic strength (salt concentration). The distinctive complementary features of DAC and c-DAC will allow them to remove a wide range of organic dyes from industrial wastewater.

Magnetite-Based Biosensors and Molecular Logic Gates: From Magnetite Synthesis to Application

In the last few decades, point-of-care (POC) sensors have become increasingly important in the detection of various targets for the early diagnostics and treatment of diseases. Diverse nanomaterials are used as building blocks for the development of smart biosensors and magnetite nanoparticles (MNPs) are among them. The intrinsic properties of MNPs, such as their large surface area, chemical stability, ease of functionalization, high saturation magnetization, and more, mean they have great potential for use in biosensors. Moreover, the unique characteristics of MNPs, such as their response to external magnetic fields, allow them to be easily manipulated (concentrated and redispersed) in fluidic media. As they are functionalized with biomolecules, MNPs bear high sensitivity and selectivity towards the detection of target biomolecules, which means they are advantageous in biosensor development and lead to a more sensitive, rapid, and accurate identification and quantification of target analytes. Due to the abovementioned properties of functionalized MNPs and their unique magnetic characteristics, they could be employed in the creation of new POC devices, molecular logic gates, and new biomolecular-based biocomputing interfaces, which would build on new ideas and principles. The current review outlines the synthesis, surface coverage, and functionalization of MNPs, as well as recent advancements in magnetite-based biosensors for POC diagnostics and some perspectives in molecular logic, and it also contains some of our own results regarding the topic, which include synthetic MNPs, their application for sample preparation, and the design of fluorescent-based molecular logic gates.

A critical review on application of organic, inorganic and hybrid nanophotocatalytic assemblies for photocatalysis of methyl orange dye in aqueous medium

Methyl orange (MO) is a highly carcinogenic and harmful contaminant, which has been extensively reported for its detrimental impact on human and aquatic life. The photodegradation of MO into less toxic products has gained much attention over the past few decades. Herein we have reviewed the recent advancement in designing of nanomaterials (NMs) stabilized on different fabricating assemblies and their application in photocatalysis of MO dye. These photocatalytic systems possess various advantages and disadvantages. Graphene-based supported materials on different NMs are highly reported photocatalysts for photocatalysis of MO dye. Recent advancement, parameters affecting photocatalytic studies, kinetics and photocatalytic mechanism of MO have been thoroughly explained in this review. Future outcomes are also provided for extending the development of scientific research in this field.

Substantial increase in adsorption efficiency of local clay-alginate beads toward methylene blue impregnated with SDS

In the current research work, local clay-alginate beads loaded with sodium dodecyl sulfate (SDS) surfactant were prepared for efficient adsorption of methylene blue (MB). FTIR, SEM-EDX, and TGA instruments were used to examine the surface functional groups, morphology, elemental analysis, and thermal stability of beads, respectively. The adsorption efficiency of native clay for MB increases from 124.78 to 247.94 mg/g when loaded in alginate and SDS in beads form. The impacts of adsorbent dosage, initial pH, contact time, initial MB concentration, and temperature were investigated and optimized. The maximum adsorption capacity of beads for MB was 1468.5 mg/g. The process followed a pseudosecond order kinetic and Freundlich adsorption isotherm model. Thermodynamic study confirmed that MB adsorption on beads is endothermic and spontaneous in nature. The beads were recycled and reused for five times. According to the findings, local clay-alginate beads impregnated with SDS proved to be a promising and efficient adsorbent for extracting MB from aqueous solution.

A comprehensive review of anionic azo dyes adsorption on surface-functionalised silicas

Surface -functionalised silica networks are advanced adsorbents. They have been given much attention for treating wastewater using the adsorption technique due to the silanol reactivity, resulting in strong binding affinities towards many pollutants. This review discusses the removal of anionic azo dyes utilising various functional groups such as amines, surfactants, polymers, macrocyclic, and other chelating groups functionalised on silica's surface. This review also reveals the steadily increasing interest in surface-functionalised silicas as adsorbents, emphasising the scholarly advancements in this field as a platform for future research. For that, adsorption capacities with different experimental conditions have been compared. The possible adsorption mechanisms, rate-limiting step, and factors affecting the anionic azo dye adsorption process have been comprehensively discussed. This review discloses that adsorbent characteristics such as porosity and functional groups, besides structural properties of an anionic azo dye, significantly affect adsorption. The adsorption process followed the Langmuir isotherm and pseudo-second-order models, with a predominantly spontaneous and endothermic nature. Multiple interactions, including electrostatic interaction, π-π interactions, and hydrogen bonding, are observed between dyes and functionalised silicas, indicating the adsorption process's complexity. Regeneration and cost-economic analysis are also presented to provide a roadmap for sustainable improvements. Chemical and biological regeneration techniques restore > 80% of the spent functionalised silicas. There is a significant opportunity to improve their efficiencies and regenerability, resulting in surface-functionalised silicas being used commercially instead of only in the laboratory. Finally, future research has been proposed by identifying current research gaps, particularly concerning the application of functionalised silicas in wastewater treatment.

Nanohybrid catalysts with porous structures for environmental remediation through photocatalytic degradation of emerging pollutants

Water supplies have been seriously challenged by new emerging pollutants, which are difficult to remove by traditional wastewater treatment. Thus, new technologies such as catalytic advanced oxidation processes have merged as suitable solutions; however, the drawbacks of typical catalysts limit their application. To overcome this issue, new materials with enhanced textural properties have been developed, showing that their porosity and chemical nature influence their potential as a catalyst. Herein, the recent progress in highly porous catalysts and their suitable deployment to effectively nano-remediate the polluted environmental matrices are reviewed in detail. First, following a brief introduction, several environmental pollutants of emerging concerns from different sectors, including pharmaceutical residues, endocrine-disrupting chemicals (EDCs), pesticides, and hazardous dyes are also introduced with relevant examples. To effectively tackle the sustainable remediation of emerging pollutants, this work also focuses on the multifunctional features of nanohybrid porous materials that act as catalysts constructs to degrade emerging pollutants. The influence of surface reactive centers, stability, bandgap energies, light absorption capacities, and pollutants adsorption capacities are also discussed. Successful examples of the employment of nanohybrid porous catalysts for the degradation of pharmaceutical pollutants, EDCs, pesticides, and hazardous dyes are summarized. Finally, some challenges faced by nanohybrid porous materials to achieve their potential application as advanced catalysts for environmental remediation have been identified and presented herein.

C. G. Mono- and Bimetallic Nanoparticles for Catalytic Degradation of Hazardous Organic Dyes and Antibacterial Applications

In the present work, gold (Au), silver (Ag), and copper (Cu) based mono- and bimetallic NPs are prepared using a cost-effective facile wet chemical route. The pH for the synthesis is optimized in accordance with the optical spectra and supported by the finite difference time domain simulation studies. FESEM and TEM micrographs are used to analyze the morphology of the prepared nanoparticles. TEM images of bimetallic nanoparticles (BMPs) verified their bimetallic nature. XRD studies confirmed the formation of fcc-structured mono- and bimetallic NPs. Photoluminescence studies of the as-synthesized NPs are in good agreement with the previous publications. These synthesized NPs showed enhanced catalytic activity for the reduction/degradation of 4-nitrophenol, rhodamine B, and indigo carmine dyes in the presence of sodium borohydride (NaBH4) compared to NaBH4 alone. For the reduction of 4-nitrophenol, Au, Cu, and CuAg nanoparticles exhibited good catalytic efficiency compared to others, whereas for the degradation of rhodamine B and indigo carmine dyes the catalytic efficiency is comparatively high for CuAg BMPs. Furthermore, the antibacterial assay is carried out, and Ag NPs display effective antibacterial activity against Klebsiella pneumoniae, Salmonella ser. Typhimurium, Acinetobacter baumannii, Shigella flexneri, and Pseudomonas aeruginosa.

Adjusting Some Properties of Poly(methacrylic acid) (Nano)Composite Hydrogels by Means of Silicon-Containing Inorganic Fillers

The present work aims to show how the main properties of poly(methacrylic acid) (PMAA) hydrogels can be engineered by means of several silicon-based fillers (Laponite XLS/XLG, montmorillonite (Mt), pyrogenic silica (PS)) employed at 10 wt% concentration based on MAA. Various techniques (FT-IR, XRD, TGA, SEM, TEM, DLS, rheological measurements, UV-VIS) were used to comparatively study the effect of these fillers, in correlation with their characteristics, upon the structure and swelling, viscoelastic, and water decontamination properties of (nano)composite hydrogels. The experiments demonstrated that the nanocomposite hydrogel morphology was dictated by the way the filler particles dispersed in water. The equilibrium swelling degree (SDe) depended on both the pH of the environment and the filler nature. At pH 1.2, a slight crosslinking effect of the fillers was evidenced, increasing in the order Mt < Laponite < PS. At pH > pKaMAA (pH 5.4; 7.4; 9.5), the Laponite/Mt-containing hydrogels displayed a higher SDe as compared to the neat one, while at pH 7.4/9.5 the PS-filled hydrogels surprisingly displayed the highest SDe. Rheological measurements on as-prepared hydrogels showed that the filler addition improved the mechanical properties. After equilibrium swelling at pH 5.4, G’ and G” depended on the filler, the Laponite-reinforced hydrogels proving to be the strongest. The (nano)composite hydrogels synthesized displayed filler-dependent absorption properties of two cationic dyes used as model water pollutants, Laponite XLS-reinforced hydrogel demonstrating both the highest absorption rate and absorption capacity. Besides wastewater purification, the (nano)composite hydrogels described here may also find applications in the pharmaceutical field as devices for the controlled release of drugs.

Color removal for large-scale interbasin water transfer: Experimental comparison of five sorption media

The increasing needs of drinking water due to population growth requires seeking for new tap water sources. However, these large-scale tap water sources are oftentimes abundant with dissolved natural organic matter (NOM), such as tannic acid issue causing color in water. If not removed at the source locations beforehand, NOM would impact coagulation and flocculation unit, and/or become precursors to prompt the production of disinfectant by-products after chlorination in drinking water treatment. This study focuses on developing and testing a suite of cost-effective, scalable, adaptable, and sustainable sorption media that can be implemented near the source locations of tap water as a pretreatment option to remove color for a long-distance interbasin transfer. Within the five tested sorption media, a media recipe of Zero-valent-Iron and Perlite based Green Sorption Media (ZIPGEM) with ingredients of 85% sand, 5% clay, 6% zero-valent-iron (ZVI) and 4% perlite by volume stood out as the best option for color removal. Findings showed that ZIPGEM can maintain a color removal of ∼77% for about 14,080 min, maintaining the effluent concentration below 40 Pt-Co units given the influent condition of 175 ± 10 Pt-Co units. A recovery on the adsorption capacity of ZIPGEM was observed around 40,000 min due to synergetic effects among several different ingredients of recycled ZVI, clay, sand, and perlites. ZIPGEM can be applied to industrial wastewater treatment for dye removal as well.

Emerging Trends in the Remediation of Persistent Organic Pollutants Using Nanomaterials and Related Processes: A Review

Persistent organic pollutants (POPs) have become a major global concern due to their large amount of utilization every year and their calcitrant nature. Due to their continuous utilization and calcitrant nature, it has led to several environmental hazards. The conventional approaches are expensive, less efficient, laborious, time-consuming, and expensive. Therefore, here in this review the authors suggest the shortcomings of conventional techniques by using nanoparticles and nanotechnology. Nanotechnology has shown immense potential for the remediation of such POPs within a short period of time with high efficiency. The present review highlights the use of nanoremediation technologies for the removal of POPs with a special focus on nanocatalysis, nanofiltration, and nanoadsorption processes. Nanoparticles such as clays, zinc oxide, iron oxide, aluminum oxide, and their composites have been used widely for the efficient remediation of POPs. Moreover, filtrations such as nanofiltration and ultrafiltration have also shown interest in the remediation of POPs from wastewater. From several pieces of literature, it has been found that nano-based techniques have shown complete removal of POPs from wastewater in comparison to conventional methods, but the cost is one of the major issues when it comes to nano- and ultrafiltration. Future research in nano-based techniques for POP remediation will solve the cost issue and will make it one of the most widely accepted and available techniques. Nano-based processes provide a sustainable solution to the problem of POPs.

Biodegradable cellulose nanocrystals hydrogels for removal of acid red 8 dye from aqueous solutions

Biodegradable cellulose nanocrystals hydrogels (CNCsH) were synthesized from cellulose nanocrystals (CNCs) which were prepared from office wastepaper (OWP) by a chemical crosslinking method using epicholorohydrin (ECH) as a cross-linker. CNCsH were tested for their swelling behavior and biodegradability and the point of zero charge had been determined. The ability of CNCsH for removing the Acid Red 8 (AR8) anionic dye from its aqueous solution was evaluated. The different parameters affecting removal of the dye, such as pH, initial concentration of dye, content of CNCs, temperature and adsorbent dosage were investigated. The optimum conditions for 68% removal efficiency were pH = 1, initial concentration of dye = 10 ppm, contact time = 105 min, CNCs content = 5% and CNCsH dosage = 0.5 g at 30 °C. The adsorption isotherms, kinetics, and thermodynamic parameters have been studied. The results showed an appropriate fit for Langmuir adsorption isotherm and pseudo-second order kinetics model with an adsorption capacity of 17.12 mg/g. According to the obtained values of thermodynamic parameters, the removal of Acid red 8 by CNCs hydrogels was exothermic spontaneous process.

Emerging Fabrication Strategies of Hydrogels and Its Applications

Recently, hydrogels have been investigated for the controlled release of bioactive molecules, such as for living cell encapsulation and matrices. Due to their remote controllability and quick response, hydrogels are widely used for various applications, including drug delivery. The rate and extent to which the drugs reach their targets are highly dependent on the carriers used in drug delivery systems; therefore the demand for biodegradable and intelligent carriers is progressively increasing. The biodegradable nature of hydrogel has created much interest for its use in drug delivery systems. The first part of this review focuses on emerging fabrication strategies of hydrogel, including physical and chemical cross-linking, as well as radiation cross-linking. The second part describes the applications of hydrogels in various fields, including drug delivery systems. In the end, an overview of the application of hydrogels prepared from several natural polymers in drug delivery is presented.

An Eco-friendly and Economical Approach for Removal of Remazol Blue, Malachite Green and Rhodamine B Dyes from Wastewater using Bio-char Derived from Chlorella Vulgaris Biomass

Background::

Rapid urbanization and industrialization has led to depletion of water resource and generation of enormous amount of wastewater. One among them is textile industry which discharge huge amount of dye wastewater into aquatic environment.

Methods::

This study deals with adsorption of Remazol blue, Malachite green and Rhodamine B dyes into bio-char derived from Chlorella vulgaris biomass cultivated from municipal wastewater. Column studies were performed to depict the industrial usage of bio-char for treatment of large quantity of wastewater. Effect of temperature, time, pH, dye concentration and adsorbent dosage on dye removal was studied in batch process.

Results::

The best batch adsorption conditions are temperature (25⁰C), time (60min), pH (7), dye concentration (100ppm) and adsorbent dosage (1g) with ± 5% for all three dyes. Dye removal percentage of bio-char increased with increased in adsorbent dosage to 94.5%, 88.2% and 90.1% for Remazol blue, Malachite green and Rhodamine B dyes at 1g/L adsorbent dosage. Freundlich isotherm exhibited correlation coefficient (R2) values of 0.99, 0.98 and 0.99 for Remazol blue, Malachite green and Rhodamine B dyes respectively. Kinetic studies revealed that all three dyes followed pseudo first order model. Increase in column bed height resulted in increased dye removal percentage since increase in bed height resulted in increase in bio-char quantity with more number of surface area.

Conclusion::

From the study, it can be concluded that Bio-char was the economical and eco-friendly alternative adsorbent for wastewater treatment process. Bio-char reusability study revealed that it could be used for 3-4 consecutive cycles.

A Comprehensive Review of Effective Adsorbents Used for the Removal of Dyes from Wastewater

Aim:

The objective of the review paper aims to explore and to provide the insight of various low-cost adsorbents prepared and used in the removal of hazardous dye pollutants from the contaminated industrial effluents.

Background:

The major untreated discharge from the textile industries constitutes a wide range of organic contaminants with the enhanced concentration of biological oxygen demand and chemical oxygen demand inthe water bodies. Dyes are considered as the major water contaminants and this quest the researchers to adopt various technologies to remove the hazardous dye pollutants from the aquatic environment. Dyes are the chemical compounds that tend to adhere themselves with metal or salts by covalent bond formation or complexes by mechanical retention or physical adsorption so as to impart colours to which it is being applied.

Objective:

Numerous treatment methodologies which have been applied to the degradation of dyes. The current study has been focused on the distinct low cost and cost-effective adsorbents used in the removal of various dye pollutants. Also, the application of nanoparticles in the removal of the hazardous dye pollutants had received great interest because of its size and high reactive nature.

Methods:

The treatment technologies used in the removal of dye pollutants from wastewater have been listed as adsorption, coagulation, electrocoagulation, flocculation, membrane filtration, oxidation and biological treatment.

Results:

The complex structure of the dyes causes a great harmful impact on the aquatic environment. Though numerous treatment technologies have been applied, adsorption has been preferred by various researchers because of its cost-effective nature.

Conclusion:

The various adsorbents are used in the removal of cationic, anionic and non-ionic dyes. The different types of adsorbent from agricultural waste, activated carbons, nanomaterials and biomaterials have been discussed with the advantages and limitations.

Recent Developments in the Application of Bio-Waste-Derived Adsorbents for the Removal of Methylene Blue from Wastewater: A Review

Over the last few years, various industries have released wastewater containing high concentrations of dyes straight into the ecological system, which has become a major environmental problem (i.e., soil, groundwater, surface water pollution, etc.). The rapid growth of textile industries has created an alarming situation in which further deterioration to the environment has been caused due to substances being left in treated wastewater, including dyes. The application of activated carbon has recently been demonstrated to be a highly efficient technology in terms of removing methylene blue (MB) from wastewater. Agricultural waste, as well as animal-based and wood products, are excellent sources of bio-waste for MB remediation since they are extremely efficient, have high sorption capacities, and are renewable sources. Despite the fact that commercial activated carbon is a favored adsorbent for dye elimination, its extensive application is restricted because of its comparatively high cost, which has prompted researchers to investigate alternative sources of adsorbents that are non-conventional and more economical. The goal of this review article was to critically evaluate the accessible information on the characteristics of bio-waste-derived adsorbents for MB’s removal, as well as related parameters influencing the performance of this process. The review also highlighted the processing methods developed in previous studies. Regeneration processes, economic challenges, and the valorization of post-sorption materials were also discussed. This review is beneficial in terms of understanding recent advances in the status of biowaste-derived adsorbents, highlighting the accelerating need for the development of low-cost adsorbents and functioning as a precursor for large-scale system optimization.

Engineered Superabsorbent Nanocomposite Reinforced with Cellulose Nanocrystals for Remediation of Basic Dyes: Isotherm, Kinetic, and Thermodynamic Studies

In this study, cellulose nanocrystals (CNCs) were produced from pea peels by acid hydrolysis to be used with pectin and acrylic acid (AAc) to form Pectin-PAAc/CNC nanocomposite by γ-irradiation. The structure, morphology, and properties of the nanocomposite were investigated using Fourier transform infrared spectroscopy (FTIR) and atomic force microscopy (AFM) techniques. The nanocomposite hydrogel was used for the removal of methylene blue dye (MB) from wastewater. The results revealed that the presence of CNCs in the polymeric matrix enhances the swelling and adsorption properties of Pectin-PAAc/CNC. The optimum adsorbate concentration is 70 mg/L. The kinetic experimental data were fit by pseudo-first-order (PFO), pseudo-second-order (PSO), and Avrami (Avr) kinetic models. It was found that the kinetic models fit the adsorption of MB well where the correlation coefficients of all kinetic models are higher than 0.97. The Avr kinetic model has the lowest ∆qe (normalized standard deviation) value, making it the most suitable one for describing the adsorption kinetics. The adsorption isotherm of MB by Pectin-PAAc follows the Brouers–Sotolongo model while that by Pectin-PAAc/CNC follows the Langmuir isotherm model. The negative values of ∆G confirmed the spontaneous nature of adsorption, and the positive value of ∆H indicated the endothermic nature of the adsorption.

Review on Methylene Blue: Its Properties, Uses, Toxicity and Photodegradation

The unavailability of clean drinking water is one of the significant health issues in modern times. Industrial dyes are one of the dominant chemicals that make water unfit for drinking. Among these dyes, methylene blue (MB) is toxic, carcinogenic, and non-biodegradable and can cause a severe threat to human health and environmental safety. It is usually released in natural water sources, which becomes a health threat to human beings and living organisms. Hence, there is a need to develop an environmentally friendly, efficient technology for removing MB from wastewater. Photodegradation is an advanced oxidation process widely used for MB removal. It has the advantages of complete mineralization of dye into simple and nontoxic species with the potential to decrease the processing cost. This review provides a tutorial basis for the readers working in the dye degradation research area. We not only covered the basic principles of the process but also provided a wide range of previously published work on advanced photocatalytic systems (single-component and multi-component photocatalysts). Our study has focused on critical parameters that can affect the photodegradation rate of MB, such as photocatalyst type and loading, irradiation reaction time, pH of reaction media, initial concentration of dye, radical scavengers and oxidising agents. The photodegradation mechanism, reaction pathways, intermediate products, and final products of MB are also summarized. An overview of the future perspectives to utilize MB at an industrial scale is also provided. This paper identifies strategies for the development of effective MB photodegradation systems.

Preferential and enhanced adsorption of methyl green on different greenly synthesized magnetite nanoparticles: investigation of the influence of the mediating plant extract’s acidity

Four magnetite nanoparticle (NP) samples have been greenly synthesized using four aqueous plant extracts, which are Artemisia herba-alba (L), Rosmarinus officinalis (L), Matricaria pubescens (L), and Juniperus phoenicia (L). The pH of these extracts are acidic (5.25, 5.05, 4.63, and 3.69, respectively). The synthesized samples were characterized by XRD, SEM, ATR-FTIR, and UV-Vis. This work aimed to study the preferential and enhanced adsorption of methyl green (MG) on the four greenly synthesized Fe₃O₄ surfaces by coupling three processes: MG adsorption in ambient dark conditions as the first process, followed by the thermocatalysis of the MG/Fe₃O₄ residual solution in the second process, and finally photocatalysis by the UV irradiation of MG/Fe₃O₄ residual solution after carrying out thermocatalysis. The novelty of this study lies in highlighting the influence of the mediating plant extract’s acidity on the magnetite NPs’ physicochemical characteristics, which impact the preferential and enhanced MG adsorption. The studied physicochemical characteristics are the functional hydroxyl group density on the magnetite surface, grain size, and band gap energy. It was found that the plant extract’s acidity has a clear effect on the studied physicochemical properties. The analysis of the FTIR spectra showed that the hydroxyl group densities differ on the four magnetite samples. Furthermore, the calculated grain sizes of the magnetite samples based on XRD spectra data vary from 29.27 to 41.49 nm. The analysis of the UV-Vis spectra of the four magnetite samples showed that the estimated direct band gap energies vary from 2.87 to 2.97 eV. The obtained results showed that the decrease of the mediating plant extract’s acidity leads to an increase in the hydroxyl group density on magnetite surfaces, which resulted in an increase in the MG adsorption capacities and yields in the first process of adsorption. Thus, MG adsorption was more preferred on greenly synthesized magnetite surfaces mediated by plant extracts with low acidity (Artemisia herba-alba (L) and Rosmarinus officinalis (L)). Furthermore, the increase of the plant extract’s acidity leads to a decrease in the particle size and an increase in the band gap energy and, therefore, to the decrease of the electron/hole pair recombination speed upon electron excitation. So, magnetite greenly synthesized from a more acidic mediating plant extract showed higher thermo- and photocatalytic activities for MG adsorption (Juniperus phoenicia (L) and Matricaria pubescens (L)). However, under photocatalysis, the enhancement is even more significant compared to thermocatalysis.

Magnetite NP samples synthesized from less acidic plant extracts have more dense active sites and prefer adsorbing more MG. The increase of plant extract acidity leads to the increase of the thermo- and photocatalytic activities of Fe₃O₄ NPs.

GC/MS screening of buckthorn phytochemicals and their use to synthesize ZnO nanoparticles for photocatalytic degradation of malachite green dye in water

Zinc oxide nanoparticles (ZnO NPs) were biosynthesized. According to gas chromatography/mass spectrometry analysis, chalcone, the main phytochemical, is probably complexed with Zn ions that are then oxidized to ZnO NPs by atmospheric O₂ during heating. The ZnO NPs were characterized by thermogravimetric analysis, Fourier transform infrared spectroscopy, X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy, and Brunauer-Emmett-Teller surface area analysis. Sphere-like ZnO NPs were formed with 11 nm mean crystallite size, 5.2 m² g^-1 surface area, and 0.02 cm³ g^-1 total pore volume. The synthesized ZnO showed excellent photocatalytic degradation (96.5±0.24% in 1 hour at 25 °C) of malachite green (MG) in aqueous solutions under ultraviolet light at optimum conditions; pH 10, MG initial concentration of 20 mg L^-1, and ZnO dose of 1.5 g L^-1. Also, ZnO showed very good reusability (92.9± 0.2% after five runs). The experimental data obeyed pseudo-first-order kinetics (R² = 0.92). The photocatalysis process was dependent on the following species in the order: OH^. > electron/positive hole pairs > O₂^.-. Moreover, photodegradation efficiency decreased in the presence of CO₃^2-, HCO₃^-, and Cl^-, but increased in the presence of NO₃^- and SO₄^2- ions. Thus, the green synthesized ZnO NPs can be applied as an efficient photocatalyst for the removal of MG from aqueous media.

Dye contaminated wastewater treatment through metal–organic framework (MOF) based materials

A complete discussion of MOFs and MOF composites such as MOF-based membranes, magnetic MOFs, and metal–organic gels (MOGs) used for dye removal along with their adsorption efficiency has been done.

Scalable fabrication of LDH-based adsorbent for the removal of nitrate with enhanced performance

The exploration of LDHs for the selective adsorption of NO3− from water has been proposed for a long time; however, their complex fabrication methods and unclear adsorption mechanism limit their further utilization.

Simultaneous adsorptive removal of conventional and emerging contaminants in multi-component systems for wastewater remediation: A critical review

The rapid growth of population and industrialization results in pollution of freshwater sources which leads to the water stress conditions on the world in future. Adsorption is a low cost and popular technique for the removal of contaminants from water bodies. Most of the reports till date are on removal of a single component from aqueous solutions using this technique, but the real-world effluent contains multiple contaminants such as dyes, heavy metals, pesticides, antibiotics and many more. Therefore, a study on simultaneous removal of contaminants is highly needed to obtain a suitable adsorbent that can be used commercially. This critical review provides a detailed study on the removal of contaminants in the presence of other contaminant/s i.e., from a multi-component system (MCS). The different possible interaction mechanisms in MCS like synergism, antagonism and non-interaction are discussed. The MCS containing the mixture of conventional contaminants such as heavy metals and dyes, and other emerging contaminants such as antibiotics, organic contaminants, pesticides and personal care products are explained in depth. This review article will be helpful for researchers working in the field of simultaneous removal of contaminants from MCSs for wastewater remediation.

Adsorptive removal of dyes from wastewater using a metal-organic framework: A review

Water pollution from synthetic dyes is a growing environmental concern because many dyes have carcinogenic effects on humans and aquatic life. Adsorption is a widely used technology for the separation and removal of dyes from wastewater. However, the dye removal process using conventional adsorbents is not sufficiently efficient for industrial wastewater. Metal-organic frameworks (MOFs) addresses these drawbacks. MOF showed excellent dye removal and degradation capacity owing to its multifunctionality, water-stability, large surface area, tunable pore size and recyclability. Magnetic MOFs retained excellent performance up to several consecutive cycles. Modified MOFs performed as Fenton-like catalysis process which generated abundant reactive radicals that degraded complex organic dyes into simple and less toxic forms which were further adsorbed onto the MOF. This review systematically compiles in-depth studies on the adsorptive removal of dyes from wastewater, MOF adsorption mechanisms, major influencing factors, to adsorption efficiency of MOFs. While all MOFs adsorb dyes through electrostatic attraction, the type of MOF, presence of functional groups, ligands, and pH significantly control the adsorption mechanism. Before developing an MOF, optimization and upgradation of factors and interaction between available adsorption site and adsorbate is needed. Finally, the prospects and new frontiers of MOFs in sustainable water treatment is discussed.

Critical review on hazardous pollutants in water environment: Occurrence, monitoring, fate, removal technologies and risk assessment

Water is required for the existence of all living things. Water pollution has grown significantly, over the decades and now it has developed as a serious worldwide problem. The presence and persistence of Hazardous pollutants such as dyes, pharmaceuticals and personal care products, heavy metals, fertilizer and pesticides and their transformed products are the matter of serious environmental and health concerns. A variety of approaches have been tried to clean up water and maintain water quality. The type of pollutants present in the water determines the bulk of technological solutions. The main objective of this article was to review the occurrences and fate of hazardous contaminants (dyes, pharmaceuticals and personal care products, heavy metals, and pesticides) found in wastewater effluents. These effluents mingle with other streams of water and that are utilized for a variety of reasons such as irrigation and other domestic activities that is further complicating the issue. It also discussed traditional treatment approaches as well as current advances in hazardous pollutants removal employing graphite oxides, carbon nanotubes, metal organic structures, magnetic nano composites, and other innovative forms of useable materials. It also discussed the identification and quantification of harmful pollutants using various approaches, as well as current advancements. Finally, a risk assessment of hazardous pollutants in water is provided in terms of the human health and the environment. This data is anticipated to serve as a foundation for future improvements in hazardous pollutant risk assessment. Furthermore, future studies on hazardous pollutants must not only emphasize on the parent chemicals, as well as on their possible breakdown products in various media.

Carrageenan-based nano-hybrid materials for the mitigation of hazardous environmental pollutants

Fast industrialization and population growth are associated with the increased release of hazardous contaminants in the environment. These hazardous substances, including pharmaceutical, biomedical, personal-care products, heavy metals, endocrine-disrupters, and colorants, pollute the ecosystem by disturbing nature's balance. Nanotechnology has paved new horizons in biochemical engineering by designing novel approaches of integrating nanoscale science with biotechnology to construct improved quality materials for target uptake of pollutants. Recently, nanostructured materials have emerged as research and development frontiers owing to their excellent properties. The tailored designing of nanohybrids constructs with physicochemical alteration enables the nano-bioadsorbent with high target specificity and efficiency. The development of eco-friendly, biodegradable, cost-efficient, and biopolymer-based nanohybrid constructs is gaining attention to remove hazardous environmental pollutants. κ-carrageenan biopolymer is frequently used with different nanomaterials to design nanohybrid bio-adsorbents to remove various contaminants. Herein, the potentialities of carrageenan-based nanohybrid constructs in environmental remediation have been summarized. Different nanostructures, e.g., silica, non-magnetic/magnetic, carbon nanotubes/nanorods, nanoclay/nanomembrane, metal organic frameworks, graphene oxide, and other nanomaterials have been described in combination with carrageenan biopolymers focusing on environmental remediation.

Toward enhanced catalytic activity of magnetic nanoparticles integrated into 3D reduced graphene oxide for heterogeneous Fenton organic dye degradation

Composite Fenton nanocatalyst was prepared by water-based in situ creation of Fe3O4 nanoparticles integrated within the self-assembly 3D reduced graphene oxide (rGO) aerogel. The hybrid applied for the degradation of Acid Green 25 (AG-25) organic dye in an aqueous solution, in the presence of H2O2. By investigating the conditions that maximize the dye adsorption by the 3D composite, it was found that the pH of the solution should be adjusted between the pKa of the functional groups present on the rGO surface (carboxylic acid) and that of the dye (sulfonic acid) to promote electrostatic interactions dye-3D structure. Performed under these conditions, Fenton degradation of AG-25 in presence of H2O2 was completed in less than 30 min, including all the intermediate products, as demonstrated by MALDI-TOF-MS analysis of the aqueous solution after discoloration. Moreover, this was achieved in a solution with as high a dye concentration of 0.5 mg/mL, with only 10 mg of 3D composite catalyst, at room temperature and without additional energy input. The high performance was attributed to the creation of charge-transfer complex between rGO and Fe3O4 nanoparticles throughout covalent bond C-O-Fe, the formation of which was promoted by the in situ synthesis procedure. For the first time, up to the authors' knowledge, AG-25 degradation mechanism was proposed.

Enhanced Visible Light Photocatalytic Degradation of Methylene Blue by CdS-ZnS-BiPO4 Nanocomposites Prepared by a Solvent-Assisted Heating Method

In this study, a ternary CdS-ZnS-BiPO4 nanocomposite, synthesized by a solvent-assisted heating method, demonstrated the highest visible light-induced photocatalysis towards the degradation of methylene blue (MB) when comparing with BiPO4, CdS-BiPO4, and ZnS-BiPO4. Transmission electron microscopy (TEM), X-ray powder diffraction (XRD), and UV-Vis diffuse reflectance spectroscopy (UV-vis DRS) were used to characterize the prepared nanocomposites. From UV-DRS results, the energy band gap of the prepared BiPO4 structures was 4.51 eV. When CdS nanoparticles were deposited on BiPO4 surface by a solvent-assisted heating method, the prepared nanocomposites exhibited visible light-responsive photocatalytic degradation toward MB (20 ppm). At a molar ratio of Cd to Zn as 1:7, the prepared CdS-ZnS-BiPO4 nanocomposites exhibited the best photocatalytic activity in degrading 95% of MB dyes, out-performing pure BiPO4, CdS-BiPO4, and ZnS-BiPO4 due to its enhanced charge separation efficiency and the lowered carrier recombination from the efficient p-n junction of unprecedented ternary composites. The investigations on mechanism conclude that the major reactive species responsible for MB degradation are holes and oxygen radicals. For practicality, the degradation efficiency for different dyestuff (Fast Green FCF, Rhodamine 6G, Acid Blue 1, methyl orange, and methyl red) degradation in the different water matrix samples (pond water, seawater, and lake water) by the prepared CdS-ZnS-BiPO4 nanocomposites was evaluated.

Photodegradation of Biohazardous Dye Brilliant Blue R Using Organometallic Silver Nanoparticles Synthesized through a Green Chemistry Method

Simple Summary

In the paper, we utilize silver nanoparticles as a catalyst in the degradation of a hazardous dye. The nanoparticles are formed from the simple silver salt by using only a plant extract from a commonly occurring herb. The plant extract contains compounds that can both reduce the silver salt and subsequently cap the surface of the as-prepared particles. There are many environmental advantages to using such an approach—nanoparticles are prepared by using simple green chemistry and the catalytic degradation of dye is carried out by sunlight energy. Such a method can be used as a very cheap, green method to neutralize hazardous substances in-house.

Abstract

Nowadays, nanostructures having tremendous chemical and physical properties are gaining attention in the biomedical industry. However, when they are prepared through classical methods (physical and chemical), they are often non-biocompatible and toxic. Considering the mentioned factors, in this research, organometallic silver nanostructures (OMAgNs) have been prepared by the green chemistry method using the acetone, methanol, and methanol-hexane-based extracts of the medicinally important plant Cichorium intybus. Secondary metabolites from C. intybus can be used as an alternative to synthetic reagents at an industrial scale to manufacture biosafe and economical nanostructures with enhanced physicochemical parameters. Prepared nanostructures were characterized using SEM, XRD, FTIR, TGA, UV, and zeta potential measurement. SEM analysis revealed different shapes of OMAgNs, prepared with various extracts. XRD analysis showed the crystallinity of the nanostructures. FTIR spectroscopy helped to identify groups of compounds present in the extracts and used for the OMAgNs synthesis. Out of the three tested OMAgNs, those prepared with methanol extract were selected due to the highest obtained yield and stability (highest negative zeta potential) and were tested as a cost-efficient and active agent to photodegrade organic pollutant, Brilliant Blue R, using energy from sunlight. A decrease in UV-VIS absorbance confirmed the rapid degradation of the dye.