1
|
Das M, Pattnaik N, Dash D, Swadesh SS, Rath S, Manek PV, Makkad RS. Comparative Evaluation of Antibacterial and Anti-Adherent Properties between Titanium Oxide, Silver Dioxide-Coated, and Conventional Orthodontic Wires Against Streptococcus Sanguis Causing Gingivitis. JOURNAL OF PHARMACY AND BIOALLIED SCIENCES 2024; 16:S945-S947. [PMID: 38595349 PMCID: PMC11001005 DOI: 10.4103/jpbs.jpbs_1174_23] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 11/15/2023] [Revised: 11/19/2023] [Accepted: 11/22/2023] [Indexed: 04/11/2024] Open
Abstract
Objective To compare the antibacterial and anti-adherent properties of conventional stainless steel (SS) orthodontic wires and surface-modified silver dioxide-coated and titanium oxide-coated SS orthodontic wires against Streptococcus sanguis causing gingivitis. Materials and Methods The study used 60 orthodontic SS wire specimens, organized into six groups of ten each. The control group had uncoated wires, and the experimental group featured wires coated with silver dioxide and titanium oxide. Surface modification was done using DC sputtering, and microbiological tests assessed the antibacterial and anti-adherent properties of the AgO2- and TiO2-coated wires. Results This study demonstrated the antibacterial effect against S. sanguis in orthodontic wires coated with the photocatalytic AgO2 and TiO2 compared to the uncoated wires. Also, this study demonstrated an anti-adherent effect in the AgO2- and TiO2-coated orthodontic wires. Moreover, the bacterial accumulation on orthodontic wires coated with AgO2 and TiO2 was lower compared to that on the uncoated wires. Conclusion During orthodontic treatment, the formation of dental plaque can be prevented by coating the surface of stainless-steel orthodontic wires with photocatalytic AgO2 and TiO2. Compared to silver dioxide, the titanium oxide-coated SS orthodontic wires showed better antibacterial and anti-adherent properties.
Collapse
Affiliation(s)
- Monalisa Das
- Department of Orthodontics and Dentofacial Orthopedics, Institute of Dental Sciences, Siksha ‘O’ Anusandhan (Deemed to be) University, Bhubaneswar, Odisha, India
| | - Naina Pattnaik
- Department of Periodontology, Kalinga Institute of Dental Sciences, KIIT Deemed to be University, Bhubaneswar, Odisha, India
| | - Debashish Dash
- Department of Orthodontics and Dentofacial Orthopedics, Meghna Institute of Dental Sciences, Nizamabad, Telangana, India
| | - Sreeman S. Swadesh
- Reader, Department of Orthodontics and Dentofacial Orthopedics, Hi-Tech Dental College and Hospital, Bhubaneswar, Odisha, India
| | - Shakti Rath
- Central Research Laboratory, Institute of Dental Sciences, Siksha ‘O’ Anusandhan (Deemed to be) University, Bhubaneswar, Odisha, India
| | - Pranav V Manek
- Senior Lecturer, Department of Oral Medicine and Radiology, Pacific Dental College and Research Centre, Udaipur, Rajasthan, India
| | - Ramanpal S. Makkad
- Department of Oral Medicine and Radiology, New Horizon Dental College and Research Institute, Sakri Bilaspur, Chhattisgarh, India
| |
Collapse
|
2
|
Ali A, Chowdhury S, Carr MA, Janorkar AV, Marquart M, Griggs JA, Bumgardner JD, Roach MD. Antibacterial and biocompatible polyaniline-doped titanium oxide layers. J Biomed Mater Res B Appl Biomater 2023; 111:1100-1111. [PMID: 36585829 DOI: 10.1002/jbm.b.35217] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 09/26/2022] [Revised: 12/07/2022] [Accepted: 12/15/2022] [Indexed: 01/01/2023]
Abstract
Titanium anodization has been shown to produce crystalline oxides exhibiting photocatalytic reactions that form reactive oxygen species (ROS) when exposed to UV light. The ROS subsequently attack bacteria cells, and thus reduce bacteria attachment on titanium implant surfaces. Polyaniline (PANI) is a conductive polymer that has shown antibacterial properties when electropolymerized onto titanium. Our research group hypothesized the addition of PANI to crystalline titanium oxide surfaces would increase the available free electrons and thus increase photocatalytic activity (PCA). This research led to the development of a novel single-step anodization approach for PANI doping crystalline titanium oxide layers. The objective of the present study was to determine the proper aniline electrolyte concentration needed to maximize the PCA and reduce bacterial attachment on the formed oxides. Aniline concentrations up to 1 M were added into a 1 M sulfuric acid electrolyte. The formed oxides exhibited increased PANI surface coverage but decreased anatase and rutile crystalline titanium oxide phase formation with increasing aniline electrolyte concentrations. Despite exhibiting the lowest levels of anatase and rutile formation, the 0.75 M and 1 M aniline oxides with the greatest PANI surface coverage also exhibited the highest PCA levels. 1 M aniline oxides showed significantly higher PCA under UVA irradiation compared to oxides formed from aniline concentrations up to 0.5 M (p < 0.001). 0.75 M aniline oxides exhibited significant reductions in Staphylococcus aureus attachment with or without UVA irradiation compared to control oxides without PANI. MTT and live/dead assays confirmed cytocompatibility and nearly 100% cell viability for the PANI doped oxides.
Collapse
Affiliation(s)
- Aya Ali
- Department of Biomedical Materials Science, University of Mississippi Medical Center, Jackson, Mississippi, USA
| | - Sheetal Chowdhury
- Department of Biomedical Materials Science, University of Mississippi Medical Center, Jackson, Mississippi, USA
| | - Mary A Carr
- Department of Cell and Molecular Biology, University of Mississippi Medical Center, Jackson, Mississippi, USA
| | - Amol V Janorkar
- Department of Biomedical Materials Science, University of Mississippi Medical Center, Jackson, Mississippi, USA
| | - Mary Marquart
- Department of Cell and Molecular Biology, University of Mississippi Medical Center, Jackson, Mississippi, USA
| | - Jason A Griggs
- Department of Biomedical Materials Science, University of Mississippi Medical Center, Jackson, Mississippi, USA
| | - Joel D Bumgardner
- Biomedical Engineering, University of Memphis, Memphis, Tennessee, USA
| | - Michael D Roach
- Department of Biomedical Materials Science, University of Mississippi Medical Center, Jackson, Mississippi, USA
| |
Collapse
|
3
|
Zhang R, Han B, Liu X. Functional Surface Coatings on Orthodontic Appliances: Reviews of Friction Reduction, Antibacterial Properties, and Corrosion Resistance. Int J Mol Sci 2023; 24:ijms24086919. [PMID: 37108082 PMCID: PMC10138808 DOI: 10.3390/ijms24086919] [Citation(s) in RCA: 4] [Impact Index Per Article: 4.0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 01/29/2023] [Revised: 03/19/2023] [Accepted: 03/31/2023] [Indexed: 04/29/2023] Open
Abstract
Surface coating technology is an important way to improve the properties of orthodontic appliances, allowing for reduced friction, antibacterial properties, and enhanced corrosion resistance. It improves treatment efficiency, reduces side effects, and increases the safety and durability of orthodontic appliances. Existing functional coatings are prepared with suitable additional layers on the surface of the substrate to achieve the abovementioned modifications, and commonly used materials mainly include metal and metallic compound materials, carbon-based materials, polymers, and bioactive materials. In addition to single-use materials, metal-metal or metal-nonmetal materials can be combined. Methods of coating preparation include, but are not limited to, physical vapor deposition (PVD), chemical deposition, sol-gel dip coating, etc., with a variety of different conditions for preparing the coatings. In the reviewed studies, a wide variety of surface coatings were found to be effective. However, the present coating materials have not yet achieved a perfect combination of these three functions, and their safety and durability need further verification. This paper reviews and summarizes the effectiveness, advantages and disadvantages, and clinical perspectives of different coating materials for orthodontic appliances in terms of friction reduction, antibacterial properties, and enhanced corrosion resistance, and discusses more possibilities for follow-up studies as well as for clinical applications in detail.
Collapse
Affiliation(s)
- Ruichu Zhang
- Department of Orthodontics, School and Hospital of Stomatology, Peking University, Beijing 100081, China
- National Center of Stomatology & National Clinical Research Center for Oral Diseases & National Engineering Laboratory for Digital and Material Technology of Stomatology & Beijing Key Laboratory for Digital Stomatology & Research Center of Engineering and Technology for Computerized Dentistry Ministry of Health & NMPA Key Laboratory for Dental Materials, Beijing 100081, China
| | - Bing Han
- Department of Orthodontics, School and Hospital of Stomatology, Peking University, Beijing 100081, China
- National Center of Stomatology & National Clinical Research Center for Oral Diseases & National Engineering Laboratory for Digital and Material Technology of Stomatology & Beijing Key Laboratory for Digital Stomatology & Research Center of Engineering and Technology for Computerized Dentistry Ministry of Health & NMPA Key Laboratory for Dental Materials, Beijing 100081, China
| | - Xiaomo Liu
- Department of Orthodontics, School and Hospital of Stomatology, Peking University, Beijing 100081, China
- National Center of Stomatology & National Clinical Research Center for Oral Diseases & National Engineering Laboratory for Digital and Material Technology of Stomatology & Beijing Key Laboratory for Digital Stomatology & Research Center of Engineering and Technology for Computerized Dentistry Ministry of Health & NMPA Key Laboratory for Dental Materials, Beijing 100081, China
| |
Collapse
|
4
|
Ali A, Chowdhury S, Janorkar A, Marquart M, Griggs JA, Bumgardner J, Roach MD. A novel single-step anodization approach for PANI-doping oxide surfaces to improve the photocatalytic activity of titanium implants. Biomed Mater 2022; 18:015010. [PMID: 36384042 DOI: 10.1088/1748-605x/aca37d] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/18/2022]
Abstract
Crystalline titanium oxides have shown photocatalytic activity (PCA) and the formation of antibacterial reactive oxygen species (ROS) when stimulated with UV light. Polyaniline (PANI) is a conductive polymer that has shown antibacterial effects. Previously, titanium oxides have been PANI-doped using a multi-step approach. In the present study, we compared PANI-doped specimens produced with a two-step method (ACV), to PANI-doped specimens produced by a novel single-step direct anodization (AAn) method, and a control group of anodized un-doped specimens. The surface morphology, oxide crystallinity, surface elemental composition, surface roughness, surface wettability, oxide adhesion, corrosion resistance, PCA, and ROS generation of each oxide group were evaluated. All groups exhibited mixed anatase and rutile phase oxides. The AAn group revealed less anatase and rutile, but more PANI-surface coverage. The AAn group exhibited significantly increased PCA after 60 minutes of direct UVA illumination compared to the ACV group, despite containing lower amounts of anatase and rutile. The ACV and AAn groups showed significant increases in ROS production after 4 hours UVA illumination while the control group showed similar ROS production. These findings suggested that PANI doping using the novel direct anodization technique significantly improved PCA even for oxides containing less crystallinity. The S. aureus attachment response to each oxide group was also compared under UVA pre-illumination, UVA direct illumination, and no illumination (dark) lighting conditions. Although no significant differences were shown in the bacterial response, both PANI-doped groups exhibited less average bacterial attachment compared to the control group. The response of MC3T3-E1 pre-osteoblast cells to each oxide group was evaluated using MTT and live/dead assays, and no evidence of cytotoxicity was found. Since many, if not most, titanium implant devices are routinely anodized as a part of the manufacturing processes, these study findings are applicable to a wide variety of implant applications.
Collapse
Affiliation(s)
- Aya Ali
- Department of Biomedical Materials Science, D528, The University of Mississippi Medical Center, 2500 North State Street, Jackson, Mississippi, 39216-4505, UNITED STATES
| | - Sheetal Chowdhury
- Department of Biomedical Materials Science, D528, The University of Mississippi Medical Center, 2500 North State Street, Jackson, Mississippi, 39216-4505, UNITED STATES
| | - Amol Janorkar
- Department of Biomedical Materials Science, D528, The University of Mississippi Medical Center, School of Dentistry, 2500 North State Street, Jackson, Mississippi, 39216-4505, UNITED STATES
| | - Mary Marquart
- Department of Microbiology and Immunology, The University of Mississippi Medical Center, 2500 North State Street, Jackson, Mississippi, 39216-4505, UNITED STATES
| | - Jason A Griggs
- Department of Biomedical Materials Science, D528, The University of Mississippi Medical Center, School of Dentistry, 2500 North State Street, Jackson, Mississippi, 39216-4505, UNITED STATES
| | - Joel Bumgardner
- Biomedical Engineering Department, The University of Memphis Herff College of Engineering, Engineering Technology Building, 330, Memphis, Tennessee, 38152, UNITED STATES
| | - Michael D Roach
- Department of Biomedical Materials Science, D528, The University of Mississippi Medical Center, 2500 North State Street, School of Dentistry, Jackson, Mississippi, 39216, UNITED STATES
| |
Collapse
|
5
|
Effects of toothbrush abrasion on surface and antibacterial properties of hydroxyapatite-tryptophan complex with gray titania. Odontology 2021; 109:819-827. [PMID: 33837507 DOI: 10.1007/s10266-021-00604-5] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/07/2020] [Accepted: 03/26/2021] [Indexed: 10/21/2022]
Abstract
Photocatalysts have attracted attention in the medical field for their antibacterial effects. However, typical photocatalysts are activated by ultraviolet rays, which may have adverse effects. Therefore, we focused on a new photocatalyst that is activated by visible light, hydroxyapatite (HAp), and amino acid complex with gray titania, and evaluated its antibacterial effects against Porphyromonas gingivalis and effect by toothbrushing. The test sample was a titanium alloy substrate, and four surface treatments were applied: (1) substrate only, (2) substrate with HAp complex, (3) substrate with HAp complex with gray titania, and (4) HAp-tryptophan complex with gray titania (TR). These surface treatments were evaluated with or without toothbrushing (8 total groups). Surface roughness (Sa), fluorescent X-ray analysis (XRF), and scanning electron microscopy (SEM) were used to evaluate surface properties. To investigate antibacterial effects, each sample was seeded with P. gingivalis, irradiated with red light, and total viable bacterial count was determined. For Sa measurement, TR showed no significant difference after toothbrushing. However, in XRF and SEM observation, TR exhibited peeling of the applied coating after toothbrushing. In the antibacterial test, TR showed a decrease in P. gingivalis under no toothbrushing condition. Conversely, with toothbrushing, the TR coating appeared to peel. However, no significant difference in P. gingivalis count was observed among all groups. HAp-tryptophan complex with gray titania coating showed an antibacterial effect against P. gingivalis when irradiated with visible light. However, toothbrushing can result in coat peeling and consequently reduce the antibacterial effect.
Collapse
|
6
|
Pantaroto HN, Cordeiro JM, Pereira LT, de Almeida AB, Nociti Junior FH, Rangel EC, Azevedo Neto NF, da Silva JHD, Barão VAR. Sputtered crystalline TiO 2 film drives improved surface properties of titanium-based biomedical implants. MATERIALS SCIENCE & ENGINEERING. C, MATERIALS FOR BIOLOGICAL APPLICATIONS 2020; 119:111638. [PMID: 33321676 DOI: 10.1016/j.msec.2020.111638] [Citation(s) in RCA: 17] [Impact Index Per Article: 4.3] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 06/01/2020] [Revised: 09/17/2020] [Accepted: 10/13/2020] [Indexed: 12/13/2022]
Abstract
Different crystalline phases in sputtered TiO2 films were tailored to determine their surface and electrochemical properties, protein adsorption and apatite layer formation on titanium-based implant material. Deposition conditions of two TiO2 crystalline phases (anatase and rutile) were established and then grown on commercially pure titanium (cpTi) by magnetron sputtering to obtain the following groups: A-TiO2 (anatase), M-TiO2 (anatase and rutile mixture), R-TiO2 (rutile). Non-treated commercially pure titanium (cpTi) was used as a control. Surfaces characterization included: chemical composition, topography, crystalline phase and surface free energy (SFE). Electrochemical tests were conducted using simulated body fluid (SBF). Albumin adsorption was measured by bicinchoninic acid method. Hydroxyapatite (HA) precipitation was evaluated after 28 days of immersion in SBF. MC3T3-E1 cell adhesion, morphology and spreading onto the experimental surfaces were evaluated by scanning electron microscopy. Sputtering treatment modified cpTi topography by increasing its surface roughness. CpTi and M-TiO2 groups presented the greatest SFE. In general, TiO2 films displayed improved electrochemical behavior compared to cpTi, with M-TiO2 featuring the highest polarization resistance. Rutile phase exhibited a greater influence on decreasing the current density and corrosion rate, while the presence of a bi-phasic polycrystalline condition displayed a more stable passive behavior. M-TiO2 featured increased albumin adsorption. HA morphology was dependent on the crystalline phase, being more evident in the bi-phasic group. Furthermore, M-TiO2 displayed normal cell adhesion and morphology. The combination of anatase and rutile structures to generate TiO2 films is a promising strategy to improve biomedical implants properties including greater corrosion protection, higher protein adsorption, bioactivity and non-cytotoxicity effect.
Collapse
Affiliation(s)
- Heloisa Navarro Pantaroto
- University of Campinas (UNICAMP), Piracicaba Dental School, Department of Prosthodontics and Periodontics, Av. Limeira, 901, Piracicaba, São Paulo 13414-903, Brazil
| | - Jairo Matozinho Cordeiro
- University of Campinas (UNICAMP), Piracicaba Dental School, Department of Prosthodontics and Periodontics, Av. Limeira, 901, Piracicaba, São Paulo 13414-903, Brazil; Institute of Biomaterials, Tribocorrosion and Nanomedicine (IBTN), Brazil
| | - Lucas Toniolo Pereira
- University of Campinas (UNICAMP), Piracicaba Dental School, Department of Prosthodontics and Periodontics, Av. Limeira, 901, Piracicaba, São Paulo 13414-903, Brazil
| | - Amanda Bandeira de Almeida
- University of Campinas (UNICAMP), Piracicaba Dental School, Department of Prosthodontics and Periodontics, Av. Limeira, 901, Piracicaba, São Paulo 13414-903, Brazil
| | - Francisco Humberto Nociti Junior
- University of Campinas (UNICAMP), Piracicaba Dental School, Department of Prosthodontics and Periodontics, Av. Limeira, 901, Piracicaba, São Paulo 13414-903, Brazil
| | - Elidiane Cipriano Rangel
- São Paulo State University (UNESP), Institute of Science and Technology, Av. Três de Março, 511, Sorocaba, São Paulo, 18087-180, Brazil
| | - Nilton Francelosi Azevedo Neto
- São Paulo State University (UNESP), Department of Physics, Av. Eng. Luís Edmundo C. Coube, 14-01, Bauru, São Paulo 17033-360, Brazil
| | - Jose Humberto Dias da Silva
- São Paulo State University (UNESP), Department of Physics, Av. Eng. Luís Edmundo C. Coube, 14-01, Bauru, São Paulo 17033-360, Brazil
| | - Valentim Adelino Ricardo Barão
- University of Campinas (UNICAMP), Piracicaba Dental School, Department of Prosthodontics and Periodontics, Av. Limeira, 901, Piracicaba, São Paulo 13414-903, Brazil; Institute of Biomaterials, Tribocorrosion and Nanomedicine (IBTN), Brazil.
| |
Collapse
|
7
|
Pantaroto HN, de Almeida AB, Gomes OP, Matos AO, Landers R, Casarin RCV, da Silva JHD, Nociti FH, Barão VAR. Outlining cell interaction and inflammatory cytokines on UV-photofunctionalized mixed-phase TiO 2 thin film. MATERIALS SCIENCE & ENGINEERING. C, MATERIALS FOR BIOLOGICAL APPLICATIONS 2020; 118:111438. [PMID: 33255031 DOI: 10.1016/j.msec.2020.111438] [Citation(s) in RCA: 4] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 05/19/2020] [Revised: 08/05/2020] [Accepted: 08/22/2020] [Indexed: 12/25/2022]
Abstract
Photofunctionalization mediated by ultraviolet (UV) light seems to be a promising approach to improve the physico-chemical characteristics and the biological response of titanium (Ti) dental implants. Seeing that photofunctionalization is able to remove carbon from the surface, besides to promote reactions on the titanium dioxide (TiO2) layer, coating the Ti with a stable TiO2 film could potentialize the UV effect. Thus, here we determined the impact of UV-photofunctionalized mixed-phase (anatase and rutile) TiO2 films on the physico-chemical properties of Ti substrate and cell biology. Mixed-phase TiO2 films were grown by radiofrequency magnetron sputtering on commercially pure titanium (cpTi) discs, and samples were divided as follow: cpTi (negative control), TiO2 (positive control), cpTi UV, TiO2 UV (experimental). Photofunctionalization was performed using UVA (360 nm - 40 W) and UVC (250 nm - 40 W) lamps for 48 h. Surfaces were analyzed in terms of morphology, topography, chemical composition, crystalline phase, wettability and surface free energy. Pre-osteoblastic cells (MC3T3E1) were used to assess cell morphology and adhesion, metabolism, mineralization potential and cytokine secretion (IFN-γ, TNF-α, IL-4, IL-6 and IL-17). TiO2-coated surfaces exhibited granular surface morphology and greater roughness. Photofunctionalization increased wettability (p < 0.05) and surface free energy (p < 0.001) on both surface conditions. TiO2-treated groups featured normal cell morphology and spreading, and greater cellular metabolic activity at 2 and 4 days (p < 0.05), whereas UV-photofunctionalized surfaces enhanced cell metabolism, cell adhered area, and calcium deposition (day 14) (p < 0.05). In general, assessed proteins were found slightly affected by either UV or TiO2 treatments. Altogether, our findings suggest that UV-photofunctionalized TiO2 surface has the potential to improve pre-osteoblastic cell differentiation and the ability of cells to form mineral nodules by modifying Ti physico-chemical properties towards a more stable context. UV-modified surfaces modulate the secretion of key inflammatory markers.
Collapse
Affiliation(s)
- Heloisa Navarro Pantaroto
- University of Campinas (UNICAMP), Piracicaba Dental School, Department of Prosthodontics and Periodontology, Av. Limeira, 901, Piracicaba, São Paulo 13414-903, Brazil
| | - Amanda B de Almeida
- University of Campinas (UNICAMP), Piracicaba Dental School, Department of Prosthodontics and Periodontology, Av. Limeira, 901, Piracicaba, São Paulo 13414-903, Brazil
| | - Orisson P Gomes
- São Paulo State University (UNESP), Department of Physics, Av. Eng. Luís Edmundo C. Coube, 14-01, Bauru, São Paulo 17033-360, Brazil
| | - Adaias O Matos
- University of Campinas (UNICAMP), Piracicaba Dental School, Department of Prosthodontics and Periodontology, Av. Limeira, 901, Piracicaba, São Paulo 13414-903, Brazil
| | - Richard Landers
- University of Campinas (UNICAMP), Gleb Wataghin Physics Institute, Department of Applied Physics, R. Sérgio Buarque de Holanda, 777, Campinas, São Paulo 13083-859, Brazil
| | - Renato Corrêa V Casarin
- University of Campinas (UNICAMP), Piracicaba Dental School, Department of Prosthodontics and Periodontology, Av. Limeira, 901, Piracicaba, São Paulo 13414-903, Brazil
| | - José Humberto D da Silva
- São Paulo State University (UNESP), Department of Physics, Av. Eng. Luís Edmundo C. Coube, 14-01, Bauru, São Paulo 17033-360, Brazil
| | - Francisco H Nociti
- University of Campinas (UNICAMP), Piracicaba Dental School, Department of Prosthodontics and Periodontology, Av. Limeira, 901, Piracicaba, São Paulo 13414-903, Brazil
| | - Valentim A R Barão
- University of Campinas (UNICAMP), Piracicaba Dental School, Department of Prosthodontics and Periodontology, Av. Limeira, 901, Piracicaba, São Paulo 13414-903, Brazil; Institute of Biomaterials, Tribocorrosion and Nanomedicine (IBTN), Brazil.
| |
Collapse
|
8
|
Functional Coatings for Orthodontic Archwires-A Review. MATERIALS 2020; 13:ma13153257. [PMID: 32707959 PMCID: PMC7435379 DOI: 10.3390/ma13153257] [Citation(s) in RCA: 24] [Impact Index Per Article: 6.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 06/13/2020] [Revised: 07/07/2020] [Accepted: 07/17/2020] [Indexed: 01/06/2023]
Abstract
In this literature review, the current state-of-art of coatings for orthodontic archwires’ increasing antimicrobial and relevant mechanical properties, such as surface topography, friction or corrosion resistance, has been presented. There is a growing request for orthodontic appliances, therefore, most researchers focus on innovative functional coatings to cover orthodontic archwires and brackets. Orthodontic appliances are exposed to the unfavorable oral cavity environment, consisting of saliva flow, food, temperature and appliance force. As a consequence, friction or biocorrosion processes may occur. This can affect the functionality of the orthodontic elements, causing changes in their microstructure, surface topography and mechanical properties. Furthermore, the material which the orthodontic archwire is made from is of particular importance in terms of the possible corrosion resistance. This is especially important for patients who are hypersensitive to metals, for example, nickel, which causes allergic reactions. In the literature, there are some studies, carried out in vitro and in vivo, mostly examining the antibacterial, antiadherent, mechanical and roughness properties of functional coatings. They are clinically acceptable but still some properties have to be studied and be developed for better results. In this paper the influence of additives such as nanoparticles of silver and nitrogen-doped TiO2 applied on orthodontic brackets by different methods on the antimicrobial properties was analyzed. Future improvement of coating techniques as well as modification of the archwire composition can reduce the release of nickel ions and eliminate friction and bacterial adhesion problems, thus accelerating treatment time.
Collapse
|
9
|
Johnson HA, Williamson RS, Marquart M, Bumgardner JD, Janorkar AV, Roach MD. Photocatalytic activity and antibacterial efficacy of UVA-treated titanium oxides. J Biomater Appl 2020; 35:500-514. [PMID: 32686588 DOI: 10.1177/0885328220942669] [Citation(s) in RCA: 8] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/16/2022]
Abstract
Studies have shown ultraviolet-A (UVA) irradiation of crystalline titanium oxides leads to the production of reactive oxygen species (ROS) via a photocatalytic process. The ROS exhibit antimicrobial properties that may be of benefit in preventing bacterial attachment to implant devices. Recent studies have suggested a potential benefit of mixed anatase and rutile oxides and dopants on the photocatalytic properties of titanium oxides. The goal of this work was to compare the photocatalytic activity of different anodized commercially pure titanium grade 4 (CPTi4) surfaces. CPTi4 specimens were anodized in three mixed-acid electrolytes to create crystalline oxide surfaces that were either primarily anatase, primarily rutile, or a combination of anatase and rutile. Additionally, the primarily anatase and combination oxides incorporated some phosphorous from the phosphoric acid component in the electrolyte. The photocatalytic activity of the anodized specimens was measured using both methylene blue (MB) degradation assay and comparing the attachment of S. aureus under irradiation with UVA light of differing intensities (1 mW/cm2, 8 mW/cm2, and 23 mW/cm2). Primarily rutile oxides exhibited significantly higher levels of MB degradation after exposure to 1 mW/cm2 UVA lights. Primarily rutile specimens also had the largest reduction in bacterial attachment followed by the mixed phase specimens and the primarily anatase specimens at 1 mW/cm2 UVA lights. Phosphorous-doped, mixed phase oxides exhibited an accelerated MB degradation response during exposure to 8 mW/cm2 and 23 mW/cm2 UVA lights. All anodized and unanodized CPTi4 groups revealed similar S. aureus attachment at the two higher UVA intensities. Although MB degradation assay and the bacteria attachment assay both confirmed photocatalytic activity of the oxides formed in this study, the results of the MB degradation assay did not accurately predict the oxides performance against S. aureus.
Collapse
Affiliation(s)
- Haden Andrew Johnson
- Department of Biomedical Materials Science, School of Dentistry, University of Mississippi Medical Center, Jackson, MS, USA
| | - Randall Scott Williamson
- Department of Biomedical Materials Science, School of Dentistry, University of Mississippi Medical Center, Jackson, MS, USA
| | - Mary Marquart
- Department of Biomedical Materials Science, School of Dentistry, University of Mississippi Medical Center, Jackson, MS, USA
| | - Joel David Bumgardner
- Department of Microbiology and Immunology, School of Medicine, University of Mississippi Medical Center, Jackson, MS, USA
| | - Amol V Janorkar
- Department of Biomedical Materials Science, School of Dentistry, University of Mississippi Medical Center, Jackson, MS, USA
| | - Michael David Roach
- Department of Biomedical Materials Science, School of Dentistry, University of Mississippi Medical Center, Jackson, MS, USA
| |
Collapse
|
10
|
A novel approach to create an antibacterial surface using titanium dioxide and a combination of dip-pen nanolithography and soft lithography. Sci Rep 2018; 8:15818. [PMID: 30361619 PMCID: PMC6202409 DOI: 10.1038/s41598-018-34198-w] [Citation(s) in RCA: 26] [Impact Index Per Article: 4.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 01/12/2018] [Accepted: 10/10/2018] [Indexed: 12/27/2022] Open
Abstract
Soft lithography and Dip-Pen Nanolithography (DPN) are techniques that have been used to modify the surface of biomaterials. Modified surfaces play a role in reducing bacterial adhesion and biofilm formation. Also, titanium dioxide has been reported as an antibacterial substance due to its photocatalytic effect. This work aimed at creating patterns on model surfaces using DPN and soft lithography combined with titanium dioxide to create functional antibacterial micropatterned surfaces, which were tested against Streptococcus mutans. DPN was used to create a master pattern onto a model surface and microstamping was performed to duplicate and transfer such patterns to medical-grade stainless steel 316L using a suspension of TiO2. Modified SS316L plates were subjected to UVA black light as photocatalytic activator. Patterns were characterized by atomic force microscopy and biologically evaluated using S. mutans. A significant reduction of up to 60% in bacterial adhesion to TiO2 -coated and -micropatterned surfaces was observed. Moreover, both TiO2 surfaces reduced the viability of adhered bacteria after UV exposure. TiO2 micropatterned demonstrated a synergic effect between physical and chemical modification against S. mutans. This dual effect was enhanced by increasing TiO2 concentration. This novel approach may be a promising alternative to reduce bacterial adhesion to surfaces.
Collapse
|
11
|
Antibacterial photocatalytic activity of different crystalline TiO2 phases in oral multispecies biofilm. Dent Mater 2018; 34:e182-e195. [DOI: 10.1016/j.dental.2018.03.011] [Citation(s) in RCA: 53] [Impact Index Per Article: 8.8] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 09/13/2017] [Revised: 03/23/2018] [Accepted: 03/23/2018] [Indexed: 11/23/2022]
|
12
|
Kuroiwa A, Nomura Y, Ochiai T, Sudo T, Nomoto R, Hayakawa T, Kanzaki H, Nakamura Y, Hanada N. Antibacterial, Hydrophilic Effect and Mechanical Properties of Orthodontic Resin Coated with UV-Responsive Photocatalyst. MATERIALS 2018; 11:ma11060889. [PMID: 29799473 PMCID: PMC6025295 DOI: 10.3390/ma11060889] [Citation(s) in RCA: 11] [Impact Index Per Article: 1.8] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 04/18/2018] [Revised: 05/19/2018] [Accepted: 05/21/2018] [Indexed: 11/16/2022]
Abstract
Photocatalysts have multiple applications in air purifiers, paints, and self-cleaning coatings for medical devices such as catheters, as well as in the elimination of xenobiotics. In this study, a coating of a UV-responsive photocatalyst, titanium dioxide (TiO₂), was applied to an orthodontic resin. The antibacterial activity on oral bacteria as well as hydrophilic properties and mechanical properties of the TiO₂-coated resin were investigated. ultraviolet A (UVA) (352 nm) light was used as the light source. Antibacterial activity was examined with or without irradiation. Measurements of early colonizers and cariogenic bacterial count, i.e., colony forming units (CFU), were performed after irradiation for different time durations. Hydrophilic properties were evaluated by water contact angle measurements. While, for the assessment of mechanical properties, flexural strength was measured by the three-point bending test. In the coat(+)light(+) samples the CFU were markedly decreased compared to the control samples. Water contact angle of the coat(+)light(+) samples was decreased after irradiation. The flexural strength of the specimen irradiated for long time showed a higher value than the required standard value, indicating that the effect of irradiation was weak. We suggest that coating with the ultraviolet responsive photocatalyst TiO₂ is useful for the development of orthodontic resin with antimicrobial properties.
Collapse
Affiliation(s)
- Akira Kuroiwa
- Department of Orthodontics, Tsurumi University School of Dental Medicine, Yokohama 230-8501, Japan.
| | - Yoshiaki Nomura
- Department of Translational Research, Tsurumi University School of Dental Medicine, Yokohama 230-8501, Japan.
| | - Tsuyoshi Ochiai
- Photocatalyst Group, Research and Development Department, Local Independent Administrative Agency Kanagawa Institute of industrial Science and TEChnology (KISTEC), 407 East Wing, Innovation Center Building, KSP, 3-2-1 Sakado, Takatsu-ku, Kawasaki, Kanagawa 213-0012, Japan.
- Materials Analysis Group, Kawasaki Technical Support Department, KISTEC, Ground Floor East Wing, Innovation Center Building, KSP, 3-2-1 Sakado, Takatsu-ku, Kawasaki, Kanagawa 213-0012, Japan.
- Photocatalysis International Research Center, Tokyo University of Science, 2641 Yamazaki, Noda, Chiba 278-8510, Japan.
| | - Tomomi Sudo
- Department of Orthodontics, Tsurumi University School of Dental Medicine, Yokohama 230-8501, Japan.
| | - Rie Nomoto
- Department of Dental Engineering, Tsurumi University School of Dental Medicine, Yokohama 230-8501, Japan.
| | - Tohru Hayakawa
- Department of Dental Engineering, Tsurumi University School of Dental Medicine, Yokohama 230-8501, Japan.
| | - Hiroyuki Kanzaki
- Department of Orthodontics, Tsurumi University School of Dental Medicine, Yokohama 230-8501, Japan.
| | - Yoshiki Nakamura
- Department of Orthodontics, Tsurumi University School of Dental Medicine, Yokohama 230-8501, Japan.
| | - Nobuhiro Hanada
- Department of Translational Research, Tsurumi University School of Dental Medicine, Yokohama 230-8501, Japan.
| |
Collapse
|
13
|
Baby RD, Subramaniam S, Arumugam I, Padmanabhan S. Assessment of antibacterial and cytotoxic effects of orthodontic stainless steel brackets coated with different phases of titanium oxide: An in-vitro study. Am J Orthod Dentofacial Orthop 2017; 151:678-684. [DOI: 10.1016/j.ajodo.2016.09.014] [Citation(s) in RCA: 11] [Impact Index Per Article: 1.6] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 05/01/2016] [Revised: 09/01/2016] [Accepted: 09/01/2016] [Indexed: 01/23/2023]
|
14
|
Constantino JA, Delgado-Rastrollo M, Pacha-Olivenza MA, González-Martín ML, Quiles M, Pérez-Giraldo C, Bruque JM, Gallardo-Moreno AM. In vivo bactericidal efficacy of the Ti6Al4V surface after ultraviolet C treatment. J Orthop Traumatol 2016; 18:59-67. [PMID: 27137674 PMCID: PMC5310995 DOI: 10.1007/s10195-016-0407-x] [Citation(s) in RCA: 3] [Impact Index Per Article: 0.4] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Submit a Manuscript] [Subscribe] [Scholar Register] [Received: 07/07/2015] [Accepted: 04/08/2016] [Indexed: 11/30/2022] Open
Abstract
Background Biomaterial-associated infections are one of the most important complications in orthopedic surgery. The main goal of this study was to demonstrate the in vivo bactericidal effect of ultraviolet (UV) irradiation on Ti6Al4V surfaces. Materials and methods An experimental model of device-related infections was developed by direct inoculation of Staphylococcus aureus into the canal of both femurs of 34 rats. A UV-irradiated Ti6Al4V pin was press-fit into the canal by retrograde insertion in one femur and the control pin was inserted into the contralateral femur. To assess the efficacy of UV radiation, the mean colony counts after inoculation in the experimental subjects and the control group were compared at different times of sacrifice and at different inoculum doses. Results At 72 h, the mean colony counts after inoculation in experimental femurs were significantly lower than those of the control group, with a reduction percentage of 76 % (p = 0.041). A similar difference between control and experimental pins was observed at 24 h using an inoculum dose <104 colony-forming units (CFU), for which the reduction percentage was 70.48 % (p = 0.017). Conclusion The irradiated surface of Ti6Al4V is able to reduce early bacterial colonization of Ti6AlV pins located in the medullar channel and in the surrounding femur. The reductions depend on the initial inoculums used to cause infection in the animals and the greatest effects are detected for inoculums <104 CFU. Level of evidence Not applicable.
Collapse
Affiliation(s)
- Juan A Constantino
- Orthopaedic and Traumatic Service, Complejo Hospitalario Universitario de Badajoz, Avenida Tellez Lafuente s/n, 06010, Badajoz, Spain.
| | - María Delgado-Rastrollo
- Department of Biomedical Sciences, Microbiology Area, Faculty of Medicine, University of Extremadura, Avda de Elvas s/n, 06006, Badajoz, Spain
- Networking Research Center on Bioengineering, Biomaterials and Nanomedicine (CIBER-BBN), Badajoz, Spain
| | - Miguel A Pacha-Olivenza
- Department of Applied Physics, Faculty of Science, University of Extremadura, Avda de Elvas s/n, 06006, Badajoz, Spain
- Networking Research Center on Bioengineering, Biomaterials and Nanomedicine (CIBER-BBN), Badajoz, Spain
| | - M Luisa González-Martín
- Department of Applied Physics, Faculty of Science, University of Extremadura, Avda de Elvas s/n, 06006, Badajoz, Spain
- Networking Research Center on Bioengineering, Biomaterials and Nanomedicine (CIBER-BBN), Badajoz, Spain
| | - Manuel Quiles
- Orthopaedic and Traumatic Service, Complejo Hospitalario Universitario de Badajoz, Avenida Tellez Lafuente s/n, 06010, Badajoz, Spain
| | - C Pérez-Giraldo
- Department of Biomedical Sciences, Microbiology Area, Faculty of Medicine, University of Extremadura, Avda de Elvas s/n, 06006, Badajoz, Spain
- Networking Research Center on Bioengineering, Biomaterials and Nanomedicine (CIBER-BBN), Badajoz, Spain
| | - José M Bruque
- Department of Applied Physics, Faculty of Science, University of Extremadura, Avda de Elvas s/n, 06006, Badajoz, Spain
- Networking Research Center on Bioengineering, Biomaterials and Nanomedicine (CIBER-BBN), Badajoz, Spain
| | - Amparo M Gallardo-Moreno
- Department of Applied Physics, Faculty of Science, University of Extremadura, Avda de Elvas s/n, 06006, Badajoz, Spain
- Networking Research Center on Bioengineering, Biomaterials and Nanomedicine (CIBER-BBN), Badajoz, Spain
| |
Collapse
|
15
|
Mhaske AR, Shetty PC, Bhat NS, Ramachandra CS, Laxmikanth SM, Nagarahalli K, Tekale PD. Antiadherent and antibacterial properties of stainless steel and NiTi orthodontic wires coated with silver against Lactobacillus acidophilus--an in vitro study. Prog Orthod 2015; 16:40. [PMID: 26576557 PMCID: PMC4648852 DOI: 10.1186/s40510-015-0110-0] [Citation(s) in RCA: 28] [Impact Index Per Article: 3.1] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/06/2015] [Accepted: 11/09/2015] [Indexed: 11/10/2022] Open
Abstract
Background The purpose of the study is to assess the antiadherent and antibacterial properties of surface-modified stainless steel and NiTi orthodontic wires with silver against Lactobacillus acidophilus. Methods This study was done on 80 specimens of stainless steel and NiTi orthodontic wires. The specimens were divided into eight test groups. Each group consisted of 10 specimens. Groups containing uncoated wires acted as a control group for their respective experimental group containing coated wires. Surface modification of wires was carried out by the thermal vacuum evaporation method with silver. Wires were then subjected to microbiological tests for assessment of the antiadherent and antibacterial properties of silver coating against L. acidophilus. Mann–Whitney U test was used to analyze the colony-forming units (CFUs) in control and test groups; and Student’s t test (two-tailed, dependent) was used to find the significance of study parameters on a continuous scale within each group. Results Orthodontic wires coated with silver showed an antiadherent effect against L. acidophilus compared with uncoated wires. Uncoated stainless steel and NiTi wires respectively showed 35.4 and 20.5 % increase in weight which was statistically significant (P < 0.001), whereas surface-modified wires showed only 4.08 and 4.4 % increase in weight (statistically insignificant P > 0.001). The groups containing surface-modified wires showed statistically significant decrease in the survival rate of L. acidophilus expressed as CFU and as log of colony count when compared to groups containing uncoated wires. It was 836.60 ± 48.97 CFU in the case of uncoated stainless steel whereas it was 220.90 ± 30.73 CFU for silver-modified stainless steel, 748.90 ± 35.64 CFU for uncoated NiTi, and 203.20 ± 41.94 CFU for surface-modified NiTi. Conclusions Surface modification of orthodontic wires with silver can be used to prevent the accumulation of dental plaque and the development of dental caries during orthodontic treatment.
Collapse
Affiliation(s)
- Arun Rameshwar Mhaske
- Department of Orthodontics and Dentofacial Orthopedics, DY Patil Dental School, Lohegaon, Pune, Maharashtra, India.
| | - Pradeep Chandra Shetty
- Department of Orthodontics and Dentofacial Orthopedics, AECS Maaruti College of Dental Sciences and Research Centre, Bangalore, India
| | - N Sham Bhat
- Department of Orthodontics and Dentofacial Orthopedics, AECS Maaruti College of Dental Sciences and Research Centre, Bangalore, India
| | - C S Ramachandra
- Department of Orthodontics and Dentofacial Orthopedics, AECS Maaruti College of Dental Sciences and Research Centre, Bangalore, India
| | - S M Laxmikanth
- Department of Orthodontics and Dentofacial Orthopedics, AECS Maaruti College of Dental Sciences and Research Centre, Bangalore, India
| | - Kiran Nagarahalli
- Department of Orthodontics and Dentofacial Orthopedics, AECS Maaruti College of Dental Sciences and Research Centre, Bangalore, India
| | - Pawankumar Dnyandeo Tekale
- Department of Orthodontics, Dr Rajesh Ramdasji Kambe Dental College and Hospital, Akola, Maharashtra, India
| |
Collapse
|
16
|
Nakajo K, Takahashi M, Kikuchi M, Takada Y, Okuno O, Sasaki K, Takahashi N. Inhibitory effect of Ti-Ag alloy on artificial biofilm formation. Dent Mater J 2014; 33:389-93. [PMID: 24786344 DOI: 10.4012/dmj.2013-334] [Citation(s) in RCA: 18] [Impact Index Per Article: 1.8] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/23/2022]
Abstract
Titanium-silver (Ti-Ag) alloy has been improved for machinability and mechanical properties, but its anti-biofilm properties have not been elucidated yet. Thus, this study aimed to evaluate the effects of Ti-Ag alloy on biofilm formation and bacterial viability in comparison with pure Ti, pure Ag and silver-palladium (Ag-Pd) alloy. Biofilm formation on the metal plates was evaluated by growing Streptococcus mutans and Streptococcus sobrinus in the presence of metal plates. Bactericidal activity was evaluated using a film contact method. There were no significant differences in biofilm formation between pure Ti, pure Ag and Ag-Pd alloy, while biofilm amounts on Ti-20% Ag and Ti-25% Ag alloys were significantly lower (p<0.05). In addition, Ti-Ag alloys and pure Ti were not bactericidal, although pure Ag and Ag-Pd alloy killed bacteria. These results suggest that Ti-20% Ag and Ti-25% Ag alloys are suitable for dental material that suppresses biofilm formation without disturbing healthy oral microflora.
Collapse
Affiliation(s)
- Kazuko Nakajo
- Division of Oral Ecology and Biochemistry, Tohoku University Graduate School of Dentistry
| | | | | | | | | | | | | |
Collapse
|
17
|
Paret ML, Vallad GE, Averett DR, Jones JB, Olson SM. Photocatalysis: effect of light-activated nanoscale formulations of TiO(2) on Xanthomonas perforans and control of bacterial spot of tomato. PHYTOPATHOLOGY 2013; 103:228-236. [PMID: 23190116 DOI: 10.1094/phyto-08-12-0183-r] [Citation(s) in RCA: 73] [Impact Index Per Article: 6.6] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 05/20/2023]
Abstract
Protection of crops from bacterial diseases presents a continuing challenge, mandating the development of novel agents and approaches. Photocatalysis is a process where chemically reactive oxygen species are catalytically generated by certain minerals in the presence of light. These reactive oxygen species have the capacity to destroy organic molecular structures critical to pathogen viability. In this study, the antibacterial potential of photocatalytic nanoscale titanium dioxide (TiO(2)), nanoscale TiO(2) doped (incorporation of other materials into the structure of TiO(2)) with silver (TiO(2)/Ag), and nanoscale TiO(2) doped with zinc (TiO(2)/Zn; AgriTitan) was evaluated against Xanthomonas perforans, the causal agent for bacterial spot disease of tomato. In vitro experiments on photocatalytic activity and dose dependency were conducted on glass cover slips coated with the nanoscale formulations by adding a known population of X. perforans strain Xp-F7 and illuminating the cover slips under a visible light source. TiO(2)/Ag and TiO(2)/Zn had high photocatalytic activity against X. perforans within 10 min of exposure to 3 × 10(4) lux. Greenhouse studies on naturally and artificially infected transplants treated with TiO(2)/Zn at ≈500 to 800 ppm significantly reduced bacterial spot severity compared with untreated and copper control. Protection was similar to the grower standard, copper + mancozeb. The use of TiO(2)/Zn at ≈500 to 800 ppm significantly reduced disease incidence in three of the four trials compared with untreated and copper control, and was comparable to or better than the grower standard. The treatments did not cause any adverse effects on tomato yield in any of the field trials.
Collapse
|
18
|
Photocatalytic and antimicrobial properties of surgical implant coatings of titanium dioxide deposited though cathodic arc evaporation. Biotechnol Lett 2012; 34:2299-305. [PMID: 22941372 DOI: 10.1007/s10529-012-1040-2] [Citation(s) in RCA: 35] [Impact Index Per Article: 2.9] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 07/24/2012] [Accepted: 08/14/2012] [Indexed: 10/27/2022]
Abstract
UNLABELLED Nanostructured crystalline titanium dioxide coatings deposited by cathodic arc evaporated on titanium grade five medical implant substrates were demonstrated to exhibit UV-induced photocatalytic activity that can be utilized to provide bactericidal effects against Staphylococcus epidermidis. The photocatalytic activity of the coatings was confirmed via degradation of Rhodamine B under UV illumination. A 90 % reduction of viable bacteria was achieved in a clinically suitable time of only 2 min with a UV dose of 2.4 J delivered at 365 nm. These results are encouraging for the development of antimicrobial surfaces in orthopedics and dentistry in order to prevent or treat post-surgical infections. PURPOSE OF WORK To assess the possibility of employing photocatalysis for elimination of S. epidermidis, known to cause medical device related infections, under short enough times to be clinically useful on an implant surface produced with a technique that is suitable for mass production.
Collapse
|
19
|
Shah AG, Shetty PC, Ramachandra CS, Bhat NS, Laxmikanth SM. In vitro assessment of photocatalytic titanium oxide surface modified stainless steel orthodontic brackets for antiadherent and antibacterial properties against Lactobacillus acidophilus. Angle Orthod 2012; 81:1028-35. [PMID: 22007663 DOI: 10.2319/021111-101.1] [Citation(s) in RCA: 39] [Impact Index Per Article: 3.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/23/2022] Open
Abstract
OBJECTIVE To assess the antiadherent and antibacterial properties of surface modified stainless steel orthodontic brackets with photocatalytic titanium oxide (TiO(2)) against Lactobacillus acidophilus. MATERIALS AND METHODS This study was done on 120 specimens of stainless steel preadjusted edgewise appliance (PEA) orthodontic brackets. The specimens were divided into four test groups. Each group consisted of 30 specimens. Groups containing uncoated brackets acted as a control group for their respective experimental group containing coated brackets. Surface modification of brackets was carried out by the radiofrequency (RF) magnetron sputtering method with photocatalytic TiO(2). Brackets then were subjected to microbiological tests for assessment of the antiadherent and antibacterial properties of photocatalytic TiO(2) coating against L acidophilus. RESULTS Orthodontic brackets coated with photocatalytic TiO(2) showed an antiadherent effect against L acidophilus compared with uncoated brackets. The bacterial mass that was bound to the TiO(2)-coated brackets was less when compared with the uncoated brackets. Furthermore, TiO(2)-coated brackets had a bactericidal effect on L acidophilus, which causes dental caries. CONCLUSION Surface modification of orthodontic brackets with photocatalytic TiO(2) can be used to prevent the accumulation of dental plaque and the development of dental caries during orthodontic treatment.
Collapse
Affiliation(s)
- Alok Girish Shah
- Department of Orthodontics and Dentofacial Orthopedics, AECS Maaruti College of Dental Sciences and Research Centre, Bangalore, India.
| | | | | | | | | |
Collapse
|
20
|
Wu P, Imlay JA, Shang JK. Mechanism of Escherichia coli inactivation on palladium-modified nitrogen-doped titanium dioxide. Biomaterials 2010; 31:7526-33. [PMID: 20637502 DOI: 10.1016/j.biomaterials.2010.06.032] [Citation(s) in RCA: 59] [Impact Index Per Article: 4.2] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 05/27/2010] [Accepted: 06/23/2010] [Indexed: 10/19/2022]
Abstract
The cellular responses of Escherichia coli to visible light photocatalysis were characterized by chemical, optical, electron-beam, and surface-force techniques, to elucidate the mechanisms of photocatalytic inactivation of E. coli on PdO/TiON fiber. The characterization techniques included chemical assays, fluorescence microscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and atomic force microscopy (AFM). Fluorescence microscopy using the Live/Dead BacLight kit indicates that the photocatalytic treatment resulted in severe membrane damage to the E. coli cells. SEM, AFM and TEM revealed drastic defects in the morphology and internal sub-structure of the bacterial cells after the treatments. Combining data from our previous reports on the antimicrobial properties of visible-light-activated PdO/TiON photocatalyst, the present results point to oxidative attack from the exterior to the interior of the bacteria by hydroxyl radicals as the primary mechanism of photocatalytic inactivation.
Collapse
Affiliation(s)
- Pinggui Wu
- Department of Materials Science and Engineering, University of Illinois at Urbana-Champaign, Urbana, IL 61801, USA.
| | | | | |
Collapse
|
21
|
Nadtochenko VA, Radtsig MA, Khmel IA. Antimicrobial effect of metallic and semiconductor nanoparticles. ACTA ACUST UNITED AC 2010. [DOI: 10.1134/s1995078010050010] [Citation(s) in RCA: 19] [Impact Index Per Article: 1.4] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/23/2022]
|
22
|
Gallardo-Moreno AM, Pacha-Olivenza MA, Fernández-Calderón MC, Pérez-Giraldo C, Bruque JM, González-Martín ML. Bactericidal behaviour of Ti6Al4V surfaces after exposure to UV-C light. Biomaterials 2010; 31:5159-68. [PMID: 20362330 DOI: 10.1016/j.biomaterials.2010.03.005] [Citation(s) in RCA: 58] [Impact Index Per Article: 4.1] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 01/20/2010] [Accepted: 03/03/2010] [Indexed: 11/28/2022]
Abstract
TiO(2)-coated biomaterials that have been excited with UV irradiation have demonstrated biocidal properties in environmental applications, including drinking water decontamination. However, this procedure has not been successfully applied towards the killing of pathogens on medical titanium-based implants, mainly because of practical concerns related to irradiating the inserted biomaterial in situ. Previous researchers assumed that the photocatalysis on the TiO(2) surface during UV application causes the bactericidal effects. However, we show that a residual post-irradiation bactericidal effect exists on the surface of Ti6Al4V, not related with photocatalysis. Using a combination of staining, serial dilutions, and a biofilm assay, we show a significant and time-dependent loss in viability of different bacterial strains of Staphylococcus epidermidis and Staphylococcus aureus on the post-irradiated surface. Although the duration of this antimicrobial effect depends on the strains selected, our experiments suggest that the effect lasts at least 60 min after surface irradiation. The origin of such phenomena is discussed in terms of the physical properties of the irradiated surfaces, which include the emission of energy and changes in surfaces charge occurring during electron-hole recombination processes. The method here proposed for the preparation of antimicrobial titanium surfaces could become especially useful in total implant surgery for which the antimicrobial challenge is mainly during or shortly after surgery.
Collapse
Affiliation(s)
- Amparo M Gallardo-Moreno
- Departamento de Física Aplicada, Facultad de Ciencias, Universidad de Extremadura, Avda de Elvas s/n, 06071 Badajoz, Spain
| | | | | | | | | | | |
Collapse
|