Research Progress of Gas Sensor Based on Graphene and Its Derivatives: A Review

Electrical Kinetic Model of a Hydroxylated Graphene FET Gas Sensor

Graphene transistor sensors, with advantages such as facile surface functionalization and high sensitivity, have gained extensive research interest in gas detection applications. This study fabricated back-gated graphene transistors and employed a hydroxylation scheme for the surface functionalization of graphene. On the basis of the interaction mechanisms between gas molecules and graphene's electrical properties, a compact electrical kinetics model considering the gas-solid surface reaction of graphene transistors is proposed. The model can accurately predict the electrical kinetic performance and can be used to optimize sensor characteristics. The bias condition of a higher response can be rapidly determined. In addition, the density of hydroxyl groups on graphene is revealed to be the direction of improvement and a key factor of response. Hence, the gas detection capacity of sensors with varying densities of hydroxyl groups was assessed concerning ammonia gas, and design technology co-optimization (DTCO) is realized. Measurement results show that the sensor with 70 s of hydroxylation time has a 7.7% response under 22 ppm ammonia gas.

A Comparative Review of Graphene and MXene-Based Composites towards Gas Sensing

Graphene and MXenes have emerged as promising materials for gas sensing applications due to their unique properties and superior performance. This review focuses on the fabrication techniques, applications, and sensing mechanisms of graphene and MXene-based composites in gas sensing. Gas sensors are crucial in various fields, including healthcare, environmental monitoring, and industrial safety, for detecting and monitoring gases such as hydrogen sulfide (H2S), nitrogen dioxide (NO2), and ammonia (NH3). Conventional metal oxides like tin oxide (SnO2) and zinc oxide (ZnO) have been widely used, but graphene and MXenes offer enhanced sensitivity, selectivity, and response times. Graphene-based sensors can detect low concentrations of gases like H2S and NH3, while functionalization can improve their gas-specific selectivity. MXenes, a new class of two-dimensional materials, exhibit high electrical conductivity and tunable surface chemistry, making them suitable for selective and sensitive detection of various gases, including VOCs and humidity. Other materials, such as metal-organic frameworks (MOFs) and conducting polymers, have also shown potential in gas sensing applications, which may be doped into graphene and MXene layers to improve the sensitivity of the sensors.

Sensing of volatile pollutants on reduced graphene oxide-polypyrrole composite: DFT investigation

Air pollutants generated from volatile toxic chemicals pose significant public health concerns. Density functional theory (DFT) computations were used in this research to explore the efficiency and mechanism of harmful gas sensing over the reduced graphene oxide-polypyrrole (rGO-PPy) composite. Volatile molecule sensing was investigated for the NH3, H2CO, CH3OH, and C2H5OH gas molecules over three PPy orientations on the rGO substrate. Results showed that PPy orientation over rGO plays a crucial role in the sensing efficiency of the investigated gas molecules. The rGO-PPy composite, with PPy in a vertical orientation, demonstrated higher stability and enhanced sensing than other orientations. The results indicate that the strong hydrogen bonding of NH3 and CH3OH with both PPy and rGO significantly enhanced the sensing of these gas molecules on rGO by influencing the charge transfer with adsorption energy values of - 0.84 and - 0.92 eV, respectively. The lack of a direct hydrogen bonding with rGO and the weak hydrogen bonding with PPy caused a weak adsorption of H2CO and C2H5OH over rGO as indicated by the adsorption energy values of - 0.60 and - 0.78 eV, respectively. Selectivity analysis for the NH3 and C2H5OH gas molecules showed that NH3 can maintain hydrogen bonding with PPy in the presence of C2H5OH while C2H5OH cannot sustain this interaction. This study highlights the importance of the structural and electronic properties of the rGO-PPy composite in volatile pollutant sensing, providing insights for designing high-performance gas sensors.

The Future of Graphene: Preparation from Biomass Waste and Sports Applications

At present, the main raw material for producing graphene is graphite ore. However, researchers actively seek alternative resources due to their high cost and environmental problems. Biomass waste has attracted much attention due to its carbon-rich structure and renewability, emerging as a potential raw material for graphene production to be used in sports equipment. However, further progress is required on the quality of graphene produced from waste biomass. This paper, therefore, summarizes the properties, structures, and production processes of graphene and its derivatives, as well as the inherent advantages of biomass waste-derived graphene. Finally, this paper reviews graphene's importance and application prospects in sports since this wonder material has made sports equipment available with high-strength and lightweight quality. Moreover, its outstanding thermal and electrical conductivity is exploited to prepare wearable sensors to collect more accurate sports data, thus helping to improve athletes' training levels and competitive performance. Although the large-scale production of biomass waste-derived graphene has yet to be realized, it is expected that its application will expand to various other fields due to the associated low cost and environmental friendliness of the preparation technique.

Selective NO2 Gas Sensors Employing Nitrogen- and Boron-Doped and Codoped Reduced Graphene Oxide

In this paper, we develop high-performance gas sensors based on heteroatom-doped and -codoped graphene oxide as a sensing material for the detection of NO2 at trace levels. Graphene oxide (GO) was doped with nitrogen and boron by a chemical method using urea and boric acid as precursors. The prepared samples were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectroscopy, X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). The obtained results proved the successful reduction of graphene oxide by doping effects, leading to the removal of some oxygen functional groups and restoration of an sp2 carbon structure. New bonds in honeycombs, such as pyridinic, pyrrolic, graphitic, B-C3, B-C2-O, and B-O, were created. Compared to the nondoped GO, the N/B-rGO materials exhibited enhanced responses toward low concentrations of NO2 (<1 ppm) at 100 °C. Particularly, the N-rGO-based device showed the highest sensitivity and lowest limit of detection.

Boron-rich hybrid BCN nanoribbons for highly ambient uptake of H2S, HF, NH3, CO, CO2 toxic gases

Nanomaterials-based gas sensors are widely applied for the monitoring and fast detection of hazardous gases owing to their sensitivity and selectivity. Hydrogen sulfide (H2S), hydrogen fluoride (HF), ammonia (NH3), and carbon monoxide/dioxide (CO/CO2) produced from petroleum fields, sewage, mines, and gasoline are harmful for both human life and environment. With an increase in the emission of these toxic compounds, their real-time monitoring and efficient adsorbent application and storage are very necessary. To this end, we investigated the adsorption characteristic and sensitivity factor of these five toxic gases on armchair and zigzag hybrid boron-carbon-nitride (BCN) nanoribbons with/without boron-rich (B-rich) defects using first principle calculation, where 25%, 33%, and 50% carbon concentration were considered. Our findings reveal that B-rich nanoribbons have strong adsorption energy, charge transfer, and structural deformation owing to the double acceptor of B-rich defects. Moreover, the zigzag and armchair forms of these hybrid BCN nanoribbons show physical adsorption, altering their band gap and phase transition after adsorbing these toxic gases, where B-rich nanoribbons possess high sensitivity to NH3 and CO among other gases. Furthermore, B-rich hybrid nanoribbons have higher CO2 adsorption energy than the standard free energy of CO2 at room temperature. This study suggests that hybrid BCN nanoribbons and B-rich defected structures can be good candidates for the uptake and storage of toxic gases, helping experimental groups to design efficient ambient gas sensors.

Carbon nanowall-based gas sensors for carbon dioxide gas detection

Carbon nanowalls (CNWs) have attracted significant attention for gas sensing applications due to their exceptional material properties such as large specific surface area, electric conductivity, nano- and/or micro-porous structure, and high charge carrier mobility. In this work, CNW films were synthesized and used to fabricate gas sensors for carbon dioxide (CO2) gas sensing. The CNW films were synthesized using an inductively-coupled plasma (ICP) plasma-enhanced chemical vapor deposition (PECVD) method and their structural and morphological properties were characterized using Raman spectroscopy and electron microscopy. The obtained CNW films were used to fabricate gas sensors employing interdigitated gold (Au) microelectrodes. The gas sensors were fabricated using both direct synthesis of CNW films on interdigitated Au microelectrodes on quartz and also transferring presynthesized CNW films onto interdigitated Au microelectrodes on glass. The CO2gas-sensing properties of fabricated devices were investigated for different concentrations of CO2gas and temperature-ranges. The sensitivities of fabricated devices were found to have a linear dependence on the concentration of CO2gas and increase with temperature. It was revealed that devices, in which CNW films have a maze-like structure, perform better compared to the ones that have a petal-like structure. A sensitivity value of 1.18% was obtained at 500 ppm CO2concentration and 100 °C device temperature. The CNW-based gas sensors have the potential for the development of easy-to-manufacture and efficient gas sensors for toxic gas monitoring.

Modifying the electronic and magnetic properties of the scandium nitride semiconductor monolayer via vacancies and doping

In this work, the effects of vacancies and doping on the electronic and magnetic properties of the stable scandium nitride (ScN) monolayer are investigated using first-principles calculations. The pristine monolayer is a two-dimensional (2D) indirect-gap semiconductor material with an energy gap of 1.59(2.84) eV as calculated using the GGA-PBE (HSE06) functional. The projected density of states, charge distribution, and electron localization function assert its ionic character generated by the charge transfer from the Sc atoms to the N atoms. The monolayer is magnetized by a single Sc vacancy with a total magnetic moment of 3.00μB, while a single N vacancy causes a weaker magnetization with a total magnetic moment of 0.52μB. In both cases, the magnetism originates mainly from the atoms closest to the defect site. Significant magnetization is also reached by doping with acceptor impurities. Specifically, a total magnetic moment of 2.00μB is obtained by doping with alkali metals (Li and Na) in the Sc sublattice and with B in the N sublattice. Doping with alkaline earth metals (Be and Mg) in the Sc sublattice and with C in the N sublattice induces a value of 1.00μB. In these cases, either magnetic semiconducting or half-metallicity characteristics arise in the ScN monolayer, making it a prospective 2D spintronic material. In contrast, no magnetism is induced by doping with donor impurities (O and F atoms) in the N sublattice. An O impurity metallizes the monolayer; meanwhile, F doping leads to a large band-gap reduction of the order of 82%, widening the working regime of the monolayer in optoelectronic devices. The results presented herein may introduce efficient methods to functionalize the ScN monolayer for optoelectronic and spintronic applications.

Doping-mediated electronic and magnetic properties of graphene-like ionic NaX (X = F and Cl) monolayers

In this work, the stability, and electronic and magnetic properties of pristine and doped graphene-like ionic NaX (X = F and Cl) monolayers are explored using first-principles calculations. The good stability of NaF and NaCl monolayers is confirmed by phonon dispersion curves and ab initio molecular dynamics simulations. Electronic structure calculations show their insulator nature with large indirect band gaps of 5.43 (7.26) and 5.06 (6.32) eV as calculated with the PBE (HSE06) functional, respectively. In addition, their ionic character is also demonstrated. Furthermore, a doping approach is explored to functionalize NaX monolayers for spintronic applications. For such a goal, IIA- and VIA-group atoms are selected as dopants due to their dissimilar valence electronic configuration as compared with the host atoms. The results indicate the emergence of magnetic semiconductor nature with a total magnetic moment of 1μB. Herein, magnetic properties are produced mainly by the dopant atoms, which induce new middle-gap energy states around the Fermi level. Finally, the effects of codoping the NaF monolayer with Ca and O and NaCl with Ba and O are also examined. Adjacent Ca-O and Ba-O pairs preserve the non-magnetic nature. Further separating dopants leads to the emergence of magnetic semiconductor behavior, with lower magnetization than separate doping. This work introduces new ionic 2D materials for optoelectronic and spintronic applications, contributing to the research effort to find out new 2D multifunctional materials.

DFT Study of Adsorption Behavior of Nitro Species on Carbon-Doped Boron Nitride Nanoribbons for Toxic Gas Sensing

The modifications of the electronic properties on carbon-doped boron nitride nanoribbons (BNNRs) as a response to the adsorption of different nitro species were investigated in the framework of the density functional theory within the generalized gradient approximation. Calculations were performed using the SIESTA code. We found that the main response involved tuning the original magnetic behavior to a non-magnetic system when the molecule was chemisorbed on the carbon-doped BNNR. It was also revealed that some species could be dissociated through the adsorption process. Furthermore, the nitro species preferred to interact over nanosurfaces where dopants substituted the B sublattice of the carbon-doped BNNRs. Most importantly, the switch on the magnetic behavior offers the opportunity to apply these systems to fit novel technological applications.

Innovations in the synthesis of graphene nanostructures for bio and gas sensors

Sensors play a significant role in modern technologies and devices used in industries, hospitals, healthcare, nanotechnology, astronomy, and meteorology. Sensors based upon nanostructured materials have gained special attention due to their high sensitivity, precision accuracy, and feasibility. This review discusses the fabrication of graphene-based biosensors and gas sensors, which have highly efficient performance. Significant developments in the synthesis routes to fabricate graphene-based materials with improved structural and surface properties have boosted their utilization in sensing applications. The higher surface area, better conductivity, tunable structure, and atom-thick morphology of these hybrid materials have made them highly desirable for the fabrication of flexible and stable sensors. Many publications have reported various modification approaches to improve the selectivity of these materials. In the current work, a compact and informative review focusing on the most recent developments in graphene-based biosensors and gas sensors has been designed and delivered. The research community has provided a complete critical analysis of the most robust case studies from the latest fabrication routes to the most complex challenges. Some significant ideas and solutions have been proposed to overcome the limitations regarding the field of biosensors and hazardous gas sensors.

Two-Dimensional Transition Metal Dichalcogenide Based Biosensors: From Fundamentals to Healthcare Applications

There has been an exponential surge in reports on two-dimensional (2D) materials ever since the discovery of graphene in 2004. Transition metal dichalcogenides (TMDs) are a class of 2D materials where weak van der Waals force binds individual covalently bonded X-M-X layers (where M is the transition metal and X is the chalcogen), making layer-controlled synthesis possible. These individual building blocks (single-layer TMDs) transition from indirect to direct band gaps and have fascinating optical and electronic properties. Layer-dependent opto-electrical properties, along with the existence of finite band gaps, make single-layer TMDs superior to the well-known graphene that paves the way for their applications in many areas. Ultra-fast response, high on/off ratio, planar structure, low operational voltage, wafer scale synthesis capabilities, high surface-to-volume ratio, and compatibility with standard fabrication processes makes TMDs ideal candidates to replace conventional semiconductors, such as silicon, etc., in the new-age electrical, electronic, and opto-electronic devices. Besides, TMDs can be potentially utilized in single molecular sensing for early detection of different biomarkers, gas sensors, photodetector, and catalytic applications. The impact of COVID-19 has given rise to an upsurge in demand for biosensors with real-time detection capabilities. TMDs as active or supporting biosensing elements exhibit potential for real-time detection of single biomarkers and, hence, show promise in the development of point-of-care healthcare devices. In this review, we provide a historical survey of 2D TMD-based biosensors for the detection of bio analytes ranging from bacteria, viruses, and whole cells to molecular biomarkers via optical, electronic, and electrochemical sensing mechanisms. Current approaches and the latest developments in the study of healthcare devices using 2D TMDs are discussed. Additionally, this review presents an overview of the challenges in the area and discusses the future perspective of 2D TMDs in the field of biosensing for healthcare devices.

A Review of Gas Measurement Practices and Sensors for Tunnels

The concentration of pollutant gases emitted by traffic in a tunnel affects the indoor air quality and contributes to structural deterioration. Demand control ventilation systems incur high operating costs, so reliable measurement of the gas concentration is essential. Numerous commercial sensor types are available with proven experience, such as optical and first-generation electrochemical sensors, or novel materials in detection methods. However, all of them are subjected to measurement deviations due to environmental conditions. This paper presents the main types of sensors and their application in tunnels. Solutions will also be discussed in order to obtain reliable measurements and improve the efficiency of the extraction systems.

A Chemiresistor Sensor Array Based on Graphene Nanostructures: From the Detection of Ammonia and Possible Interfering VOCs to Chemometric Analysis

Sensor arrays are currently attracting the interest of researchers due to their potential of overcoming the limitations of single sensors regarding selectivity, required by specific applications. Among the materials used to develop sensor arrays, graphene has not been so far extensively exploited, despite its remarkable sensing capability. Here we present the development of a graphene-based sensor array prepared by dropcasting nanostructure and nanocomposite graphene solution on interdigitated substrates, with the aim to investigate the capability of the array to discriminate several gases related to specific applications, including environmental monitoring, food quality tracking, and breathomics. This goal is achieved in two steps: at first the sensing properties of the array have been assessed through ammonia exposures, drawing the calibration curves, estimating the limit of detection, which has been found in the ppb range for all sensors, and investigating stability and sensitivity; then, after performing exposures to acetone, ethanol, 2-propanol, sodium hypochlorite, and water vapour, chemometric tools have been exploited to investigate the discrimination capability of the array, including principal component analysis (PCA), linear discriminant analysis (LDA), and Mahalanobis distance. PCA shows that the array was able to discriminate all the tested gases with an explained variance around 95%, while with an LDA approach the array can be trained to accurately recognize unknown gas contribution, with an accuracy higher than 94%.

The Effect of Different Morphologies of WO3/GO Nanocomposite on Photocatalytic Performance

Tungsten trioxide/graphene oxide (WO₃/GO) nanocomposites have been successfully synthesized using in situ and ex situ chemical approaches. Graphite and tungsten carbide (WC) were employed to perform in situ synthesis, and WO₃ and GO were employed to perform the ex situ synthesis of WO₃/GO nanocomposites. GO, which was required for ex situ synthesis, is synthesized via the modified and improved Hummers method. XRD, SEM/EDS, and FTIR are used for the characterization of the nanocomposite. From the XRD of the WO₃/GO nanocomposites, it was observed that WO₃ distributed uniformly on graphene oxide sheets or was incorporated between the sheets. The photocatalytic activities of WO₃/GO nanocomposites were evaluated by methylene blue (MB) adsorption and visible light photocatalytic degradation activities by UV-vis spectroscopy. The results showed that the efficiency of the photocatalytic activity of the nanocomposite depends on different synthesis methods and the morphology resulting from the changed method. WO₃/GO nanocomposites synthesized by both methods exhibited much higher photocatalytic efficiencies than pure WO₃, and the best degradation efficiencies for MB was 96.30% for the WO₃/GO in situ synthesis nanocomposite.

Graphene Synthesis Techniques and Environmental Applications

Graphene is fundamentally a two-dimensional material with extraordinary optical, thermal, mechanical, and electrical characteristics. It has a versatile surface chemistry and large surface area. It is a carbon nanomaterial, which comprises sp² hybridized carbon atoms placed in a hexagonal lattice with one-atom thickness, giving it a two-dimensional structure. A large number of synthesis techniques including epitaxial growth, liquid phase exfoliation, electrochemical exfoliation, mechanical exfoliation, and chemical vapor deposition are used for the synthesis of graphene. Graphene prepared using different techniques can have a number of benefits and deficiencies depending on its application. This study provides a summary of graphene preparation techniques and critically assesses the use of graphene, its derivates, and composites in environmental applications. These applications include the use of graphene as membrane material for the detoxication and purification of water, active material for gas sensing, heavy metal ions detection, and CO₂ conversion. Furthermore, a trend analysis of both synthesis techniques and environmental applications of graphene has been performed by extracting and analyzing Scopus data from the past ten years. Finally, conclusions and outlook are provided to address the residual challenges related to the synthesis of the material and its use for environmental applications.

Au3-Decorated graphene as a sensing platform for O2 adsorption and desorption kinetics

The adsorption and desorption kinetics of molecules is of significant fundamental and applied interest. In this paper, we present a new method to quantify the energy barriers for the adsorption and desorption of gas molecules on few-atom clusters, by exploiting reaction induced changes of the doping level of a graphene substrate. The method is illustrated for oxygen adsorption on Au₃ clusters. The gold clusters were deposited on a graphene field effect transistor and exposed to O₂. From the change in graphene's electronic properties during adsorption, the energy barrier for the adsorption of O₂ on Au₃ is estimated to be 0.45 eV. Electric current pulses increase the temperature of the graphene strip in a controlled way and provide the required thermal energy for oxygen desorption. The oxygen binding energy on Au₃/graphene is found to be 1.03 eV and the activation entropy is 1.4 meV K^-1. The experimental values are compared and interpreted on the basis of density functional theory calculations of the adsorption barrier, the binding energy and the activation entropy. The large value of the activation entropy is explained by the hindering effect that the adsorbed O₂ has on the fluxional motion of the Au₃ cluster.

Pushing Down the Limit of NH3 Detection of Graphene-Based Chemiresistive Sensors through Functionalization by Thermally Activated Tetrazoles Dimerization

An easy and cost-effective method is presented to functionalize graphene through thermally activated dimerization of 2,5-diaryltetrazoles. Consistently with the experimental spectroscopic results, theoretical calculations demonstrate that during the thermal treatment a dimerization process to tetrazine is energetically more favorable than covalent grafting. Since both the functionalization method by thermal activation and the use of tetrazoles have never been considered before to prepare graphene-based chemiresistors, this represents a promising approach to develop graphene-related sensing platforms. Five different 2,5-diaryltetrazoles have been tested here for the effective functionalization of low-defect graphene layers on silicon nitride. Based on these layers, an array of sensors has been prepared for testing upon ammonia exposure. The tests on the sensing performances clearly show sensitivity to ammonia, extending the current range of ammonia detection with a graphene-based chemiresistor down to the sub-ppm range, as results from a benchmarking with data available in the literature. Furthermore, all sensors perform better than bare graphene. Density functional theory (DFT) calculations, carried out on a model of the best performing layer of the array, provided the theoretical framework to rationalize the sensing mechanism and disclose a dual role played by the tetrazine molecules, (i) acting as ammonia concentrators and (ii) mediating the electron transfer between ammonia and graphene.

Design of an all-optical insulator-metal-insulator and metal-insulator-metal Feynman logic gates

In this paper, two Feynman logic gates based on insulator-metal-insulator (IMI) and metal-insulator-metal (MIM) waveguides are proposed. The gates are modeled using the finite-difference time-domain method. The IMI-based Feynman gate shows high extinction ratio (ER) values of 11.06 dB and 7.61 dB for the output bits P and Q, respectively. The ER values of the MIM-based Feynman gate are also 12.83 dB and 7.29 dB for the output bits P and Q, respectively. The footprint of the gates is less than 2µm². The proposed gates benefit from high ERs in the wavelength range of 1.5-1.6 µm (band C), ultra-compact footprints, and CMOS-compatible structures, which make them potential candidates for use in integrated photonic circuits.

Adsorption of gas molecules on buckled GaAs monolayer: a first-principles study

The design of sensitive and selective gas sensors can be significantly simplified if materials that are intrinsically selective to target gas molecules can be identified. In recent years, monolayers consisting of group III-V elements have been identified as promising gas sensing materials. In this article, we investigate gas adsorption properties of buckled GaAs monolayer using first-principles calculations within the framework of density functional theory. We examine the adsorption energy, adsorption distance, charge transfer, and electron density difference to study the strength and nature of adsorption. We calculate the change in band structure, work function, conductivity, density of states, and optical reflectivity for analyzing its prospect as work function-based, chemiresistive, optical, and magnetic gas sensor applications. In this regard, we considered the adsorption of ten gas molecules, namely NH3, NO2, NO, CH4, H2, CO, SO2, HCN, H2S, and CO2, and noticed that GaAs monolayer is responsive to NO, NO2, NH3, and SO2 only. Specifically, NH3, SO2 and NO2 chemisorb on the GaAs monolayer and change the work function by more than 5%. While both NO and NO2 are found to be responsive in the far-infrared (FIR) range, NO shows better spin-splitting property and a significant change in conductivity. Moreover, the recovery time at room temperature for NO is observed to be in the sub-millisecond range suggesting selective and sensitive NO response in GaAs monolayer.

Surface Properties of CVD-Grown Graphene Transferred by Wet and Dry Transfer Processes

Graphene, an atomically thin material, has unique electrical, mechanical, and optical properties that can enhance the performance of thin film-based flexible and transparent devices, including gas sensors. Graphene synthesized on a metallic catalyst must first be transferred onto a target substrate using wet or dry transfer processes; however, the graphene surface is susceptible to chemical modification and mechanical damage during the transfer. Defects on the graphene surface deteriorate its excellent intrinsic properties, thus reducing device performance. In this study, the surface properties of transferred graphene were investigated according to the transfer method (wet vs. dry) and characterized using atomic force microscopy, Raman spectroscopy, and contact angle measurements. After the wet transfer process, the surface properties of graphene exhibited tendencies similar to the poly(methyl methacrylate) residue remaining after solvent etching. The dry-transferred graphene revealed a surface closer to that of pristine graphene, regardless of substrates. These results provide insight into the utilization of wet and dry transfer processes for various graphene applications.

Defective ZnO Nanoflowers Decorated by Ultra-Fine Pd Clusters for Low-Concentration CH4 Sensing: Controllable Preparation and Sensing Mechanism Analysis

To detect low concentration of CH4 is indeed meaningful in industrial manufacturing, such as the petrochemical industry and natural gas catalysis, but it is not easy to detect low concentration of CH4 due to its high symmetrical and stable structure. In this work, defect-rich ZnO1−x nanoflowers (NFs) were synthesized by a two-step route so as to obtain defect-enhanced gas-sensing performance, namely hydrothermal synthesis followed by H2 treatment. In order to achieve low-concentration detection of CH4, the ultra-thin Pd clusters’ (Cs, diameter about 1–2 nm) sensitizer was synthesized and decorated onto the surface of ZnO1−x NFs. It is found that Pd Cs-2/ZnO1−x gas sensors show enhanced gas-sensing properties to CH4, even at ppm concentration level. At its optimal working temperature of 260 °C, the gas response to 50 ppm CH4 can reach 5.0 with good gas selectivity; the response and recovery time is only 16.2 and 13.8 s, respectively. In the Results, we discussed the CH4 gas-sensing mechanism deeply. Overall, it is very necessary to detect low-concentration methane safely. It is possible for further safe detection of low-concentration methane gas in the future.

A Comparative Investigation of Chemically Reduced Graphene Oxide Thin Films Deposited via Spray Pyrolysis

We present a comparative investigation between thin films of graphene oxide (GO) and chemically reduced graphene oxide (rGO) deposited onto glass substrates via spray pyrolysis. Two reduction techniques are investigated: (1) the exposition of a sprayed layer of GO to vapors of hydrazine hydrate to produce rGOV and (2) the addition of liquid hydrazine hydrate to a suspended GO solution, which is then sprayed onto a substrate to produce rGOL. Three different spectroscopy techniques, Raman, Fourier transform infrared, and UV-Vis-NIR, show that the two reduced samples have less lattice disorder in comparison to GO, with rGOL having the highest degree of reduction. Interestingly, topography characterization by atomic force microscopy reveals a morphological change occurring during the exposure to hydrazine hydrate vapors, resulting in a thickness of 110 nm for the rGOV film, which is a factor of 16 larger than rGOL and GO. Finally, I-V measurements show a significant decrease of the GO's resistivity after the reduction process, where rGOL features a resistivity 90 times lower than rGOV, confirming that rGOL has the highest degree of reduction. Our results indicate that the reduction process for rGOV is susceptible to introducing intercalated water molecules in the material while the fabrication technique for rGOL is a suitable route to obtain a material with minimal lattice disorder and properties approaching those of graphene.

Comprehensive Data via Spectroscopy and Molecular Dynamics of Chemically Treated Graphene Nanoplatelets

Graphene nanoplatelets (GnPs) are promising candidates for gas sensing applications because they have a high surface area to volume ratio, high conductivity, and a high temperature stability. The information provided in this data article will cover the surface and structural properties of pure and chemically treated GnPs, specifically with carboxyl, ammonia, nitrogen, oxygen, fluorocarbon, and argon. Molecular dynamics and adsorption calculations are provided alongside characterization data, which was performed with Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and X-ray diffraction (XRD) to determine the functional groups present and effects of those groups on the structural and vibrational properties. Certain features in the observed Raman spectra are attributed to the variations in concentration of the chemically treated GnPs. XRD data show smaller crystallite sizes for chemically treated GnPs that agree with images acquired with scanning electron microscopy. A molecular dynamics simulation is also employed to gain a better understanding of the Raman and adsorption properties of pure GnPs.

Experimental Study on Properties of Ultrasonic Coupling Agent with Graphene in NDT

An ultrasonic coupling agent, as an acoustic medium between the ultrasonic probe and the surface of the specimens, is indispensable in Nondestructive Testing (NDT). Whether it is liquid, air, or solid coupling agent, the problem of improving the efficiency of ultrasonic propagation in a coupling agent is one worth studying. Glycerol and hydrogels are two common liquid coupling agents in NDT. This study intended to investigate the effect of graphene addition on the performance of these coupling agents in NDT. Firstly, based on the theory of acoustic impedance matching, the authors established an index system to evaluate the performance of ultrasonic coupling agent by experiments. Secondly, hydrogel–graphene and glycerol–graphene composite coupling agents were prepared by adding three-dimensional graphene structure powders with mass fraction of 0.25%, 0.5%, 0.75%, and 1% to CG-98 hydrogel coupling agent and HG-99 glycerol coupling agent, respectively. Corresponding experiments were conducted on these composite coupling agents. Peak-to-peak value, attenuation coefficient, and energy value of first echo are calculated at different frequencies. The experimental results showed that graphene can significantly improve the ultrasonic propagation performance of hydrogel and glycerin coupling agents. In addition, when the mass fraction of graphene added was 0.75%, the coupling agent had the best performance. Finally, we measured the acoustic impedance values of the composite couplings with different graphene contents to demonstrate the reliability of the experimental results.

Tunning the Gas Sensing Properties of rGO with In2O3 Nanoparticles

Here, we discuss the effect of In2O3 nanoparticles on the reduced graphene oxide (rGO) gas-sensing potentialities. In2O3 nanoparticles were prepared with the polymer precursors method, while the nanocomposites were prepared by mixing an In2O3 nanoparticle suspension with an rGO suspension in different proportions. The gas-sensing performance of our materials was tested by exposing our materials to known concentrations of a target toxic gas in a dry airflow. Our results demonstrate that In2O3 nanoparticles enhance the rGO sensitivity for strong oxidizing species such as O3 and NO2, while a negative effect on its sensitivity for NH3 sensing is observed. Furthermore, our measurements towards H2S suggest that the concentration of In2O3 nanoparticles can induce an uncommon transition from p-type to n-type semiconductor nature when rGO–In2O3 nanocomposites operate at temperatures close to 160 °C.

Machine learning-based prediction of the adsorption energy of CO on boron-doped graphene

To accurately and quickly investigate the adsorption ability of different boron-doped graphene for CO, 1864 different sets of CO adsorption energy on boron-doped graphene were obtained by simulation, and an overall framework based on machine learning was proposed.

Selectivity in trace gas sensing: recent developments, challenges, and future perspectives

Selectivity is one of the most crucial figures of merit in trace gas sensing, and thus a comprehensive assessment is necessary to have a clear picture of sensitivity, selectivity, and their interrelations in terms of quantitative and qualitative views.

Graphene Field Effect Transistors: A Sensitive Platform for Detecting Sarin

Real time, rapid, and accurate detection of chemical warfare agents (CWA) is an ongoing security challenge. Typical detection methods for CWA are adapted from traditional chemistry techniques such as chromatography and mass spectrometry, which lack portability. Here, we address this challenge by evaluating graphene field effect transistors (GFETs) as a sensing platform for sarin gas using both experiment and theory. Experimentally, we measure the sensing response of GFETs when exposed to dimethyl methylphosphonate (DMMP), a less toxic compound used as simulant due to its chemical similarities to sarin. We find low detection limits of 800 ppb, the highest sensitivity reported up to date for this type of sensing platform. In addition to changes in resistance, we implement an in-operando monitor of the GFETs characteristics during and after exposure to the analyte, which gives insights into the graphene-DMMP interactions. Moreover, using theoretical calculations, we show that DMMP and sarin interact similarly with graphene, implying that GFETs should be highly sensitive to detecting sarin. GFETs offer a versatile platform for the development of compact and miniaturized devices that can provide real-time detection of dangerous chemicals in the local environment.

Low-Operating-Temperature NO2 Sensor Based on a CeO2/ZnO Heterojunction

CeO₂/ZnO-heterojunction-nanorod-array-based chemiresistive sensors were studied for their low-operating-temperature and gas-detecting characteristics. Arrays of CeO₂/ZnO heterojunction nanorods were synthesized using anodic electrodeposition coating followed by hydrothermal treatment. The sensor based on this CeO₂/ZnO heterojunction demonstrated a much higher sensitivity to NO₂ at a low operating temperature (120 °C) than the pure-ZnO-based sensor. Moreover, even at room temperature (RT, 25 °C) the CeO₂/ZnO-heterojunction-based sensor responds linearly and rapidly to NO₂. This sensor's reaction to interfering gases was substantially less than that of NO₂, suggesting exceptional selectivity. Experimental results revealed that the enhanced gas-sensing performance at the low operating temperature of the CeO₂/ZnO heterojunction due to the built-in field formed after the construction of heterojunctions provides additional carriers for ZnO. Thanks to more carriers in the ZnO conduction band, more oxygen and target gases can be adsorbed. This explains the enhanced gas sensitivity of the CeO₂/ZnO heterojunction at low operating temperatures.

Macrocycle-Functionalized RGO for Gas Sensors for BTX Detection Using a Double Transduction Mode

To fabricate mass and resistive sensors based on reduced graphene oxide (RGO), we investigated the functionalization of RGO by tetra tert-butyl phthalocyanine (PcH2tBu), which possesses a macroring and tert-butyl peripheral groups. Herein, we present the gas sensor responses of the functionalized RGO toward benzene, toluene, and xylene (BTX) vapors. The RGO was obtained by the reduction of graphene oxide (GO) using citrate as a reducing agent, while the functionalization was achieved non-covalently by simply using ultrasonic and heating treatment. The sensor devices based on both QCM (quartz crystal microbalance) and resistive transducers were used simultaneously to understand the reactivity. Both the GO and the RGO showed less sensitivity to BTX vapors, while the RGO/PcH2tBu presented enhanced sensor responses. These results show that the p-network plays a very important role in targeting BTX vapors. The resistive response analysis allowed us to state that the RGO is a p-type semiconductor and that the interaction is governed by charge transfer, while the QCM response profiles allowed use to determine the differences between the BTX vapors. Among BTX, benzene shows the weakest sensitivity and a reactivity in the higher concentration range (>600 ppm). The toluene and xylene showed linear responses in the range of 100–600 ppm.

Recent trends in gas sensing via carbon nanomaterials: outlook and challenges

The presence of harmful and poisonous gases in the environment can have dangerous effects on human health, and therefore portable, flexible, and highly sensitive gas sensors are in high demand for environmental monitoring, pollution control, and medical diagnosis. Currently, the commercialized sensors are based on metal oxides, which generally operate at high temperatures. Additionally, the desorption of chemisorbed gas molecules is also challenging. Hence, due to the large surface area, high flexibility, and good electrical properties of carbon nanomaterials (CNMs) such as carbon nanotubes, graphene and their derivatives (graphene oxide, reduced graphene oxide, and graphene quantum dots), they are considered to be the most promising chemiresistive sensing materials, where their electrical resistance is affected by their interaction with the analyte. Further, to increase their selectivity, nanocomposites of CNMs with metal oxides, metallic nanoparticles, chalcogenides, and polymers have been studied, which exhibit better sensing capabilities even at room temperature. This review summarizes the state-of-the-art progress in research related to CNMs-based sensors. Moreover, to better understand the analyte adsorption on the surface of CNMs, various sensing mechanisms and dependent sensing parameters are discussed. Further, several existing challenges related to CNMs-based gas sensors are elucidated herein, which can pave the way for future research in this area.

Emerging properties of carbon based 2D material beyond graphene

Graphene turns out to be the pioneering material for setting up boulevard to a new zoo of recently proposed carbon based novel two dimensional (2D) analogues. It is evident that their electronic, optical and other related properties are utterly different from that of graphene because of the distinct intriguing morphology. For instance, the revolutionary emergence of Dirac cones in graphene is particularly hard to find in most of the other 2D materials. As a consequence the crystal symmetries indeed act as a major role for predicting electronic band structure. Since tight binding calculations have become an indispensable tool in electronic band structure calculation, we indicate the implication of such method in graphene's allotropes beyond hexagonal symmetry. It is to be noted that some of these graphene allotropes successfully overcome the inherent drawback of the zero band gap nature of graphene. As a result, these 2D nanomaterials exhibit great potential in a broad spectrum of applications, viz nanoelectronics, nanooptics, gas sensors, gas storages, catalysis, and other specific applications. The miniaturization of high performance graphene allotrope based gas sensors to microscopic or even nanosized range has also been critically discussed. In addition, various optical properties like the dielectric functions, optical conductivity, electron energy loss spectra reveal that these systems can be used in opto-electronic devices. Nonetheless, the honeycomb lattice of graphene is not superconducting. However, it is proposed that the tetragonal form of graphene can be intruded to form new hybrid 2D materials to achieve novel superconducting device at attainable conditions. These dynamic experimental prospects demand further functionalization of these systems to enhance the efficiency and the field of multifunctionality. This topical review aims to highlight the latest advances in carbon based 2D materials beyond graphene from the basic theoretical as well as future application perspectives.

Graphene oxide nanocomposites based room temperature gas sensors: A review

Over the last few decades, various volatile organic compounds (VOCs) have been widely used in the processing of building materials and this practice adversely affected the environment i.e. both indoor and outdoor air quality. A cost-effective solution for detecting a wide range of VOCs by sensing approaches includes chemiresistive, optical and electrochemical techniques. Room temperature (RT) chemiresistive gas sensors are next-generation technologies desirable for self-powered or battery-powered instruments utilized in monitoring emissions that are associated with indoor/outdoor air pollution and industrial processes. In this review, a state-of-the-art overview of chemiresistive gas sensors is provided based on their attractive analytical characteristics such as high sensitivity, selectivity, reproducibility, rapid assay time and low fabrication cost. The review mainly discusses the recent advancement and advantages of graphene oxide (GO) nanocomposites-based chemiresistive gas sensors and various factors affecting their sensing performance at RT. Besides, the sensing mechanisms of GO nanocomposites-based chemiresistive gas sensors derived using metals, transition metal oxides (TMOs) and polymers were discussed. Finally, the challenges and future perspectives of GO nanocomposites-based RT chemiresistive gas sensors are addressed.

A Review on the Production Methods and Applications of Graphene-Based Materials

Graphene-based materials in the form of fibres, fabrics, films, and composite materials are the most widely investigated research domains because of their remarkable physicochemical and thermomechanical properties. In this era of scientific advancement, graphene has built the foundation of a new horizon of possibilities and received tremendous research focus in several application areas such as aerospace, energy, transportation, healthcare, agriculture, wastewater management, and wearable technology. Although graphene has been found to provide exceptional results in every application field, a massive proportion of research is still underway to configure required parameters to ensure the best possible outcomes from graphene-based materials. Until now, several review articles have been published to summarise the excellence of graphene and its derivatives, which focused mainly on a single application area of graphene. However, no single review is found to comprehensively study most used fabrication processes of graphene-based materials including their diversified and potential application areas. To address this genuine gap and ensure wider support for the upcoming research and investigations of this excellent material, this review aims to provide a snapshot of most used fabrication methods of graphene-based materials in the form of pure and composite fibres, graphene-based composite materials conjugated with polymers, and fibres. This study also provides a clear perspective of large-scale production feasibility and application areas of graphene-based materials in all forms.

Nitrogen Dioxide Gas Sensor Based on Ag-Doped Graphene: A First-Principle Study

High-performance tracking trace amounts of NO2 with gas sensors could be helpful in protecting human health since high levels of NO2 may increase the risk of developing acute exacerbation of chronic obstructive pulmonary disease. Among various gas sensors, Graphene-based sensors have attracted broad attention due to their sensitivity, particularly with the addition of noble metals (e.g., Ag). Nevertheless, the internal mechanism of improving the gas sensing behavior through doping Ag is still unclear. Herein, the impact of Ag doping on the sensing properties of Graphene-based sensors is systematically analyzed via first principles. Based on the density-functional theory (DFT), the adsorption behavior of specific gases (NO2, NH3, H2O, CO2, CH4, and C2H6) on Ag-doped Graphene (Ag–Gr) is calculated and compared. It is found that NO2 shows the strongest interaction and largest Mulliken charge transfer to Ag–Gr among these studied gases, which may directly result in the highest sensitivity toward NO2 for the Ag–Gr-based gas sensor.

Recent Advances in ZnO-Based Carbon Monoxide Sensors: Role of Doping

Monitoring and detecting carbon monoxide (CO) are critical because this gas is toxic and harmful to the ecosystem. In this respect, designing high-performance gas sensors for CO detection is necessary. Zinc oxide-based materials are promising for use as CO sensors, owing to their good sensing response, electrical performance, cost-effectiveness, long-term stability, low power consumption, ease of manufacturing, chemical stability, and non-toxicity. Nevertheless, further progress in gas sensing requires improving the selectivity and sensitivity, and lowering the operating temperature. Recently, different strategies have been implemented to improve the sensitivity and selectivity of ZnO to CO, highlighting the doping of ZnO. Many studies concluded that doped ZnO demonstrates better sensing properties than those of undoped ZnO in detecting CO. Therefore, in this review, we analyze and discuss, in detail, the recent advances in doped ZnO for CO sensing applications. First, experimental studies on ZnO doped with transition metals, boron group elements, and alkaline earth metals as CO sensors are comprehensively reviewed. We then focused on analyzing theoretical and combined experimental-theoretical studies. Finally, we present the conclusions and some perspectives for future investigations in the context of advancements in CO sensing using doped ZnO, which include room-temperature gas sensing.

Review of Fiber Optical Sensors and Its Importance in Sewer Corrosion Factor Analysis

Adverse effects of wastewater on the hygiene of human and circumstances is a major issue in society. Appropriate refining systems with high efficiency is required to treat the wastewater. Sewage treatment plant plays a major and important role in conserving incredible nature of the environment. Microbiologically Induced Corrosion (MIC) is an important phenomenon in sewage structures which causes the deterioration of infrastructures. Huge capital has been spent and efforts have been made on wastewater treatment infrastructure to increase operating efficiency and reliability of compliance. The investments in reimbursement and maintenance of sewer structures upsurge with an increase in the rate of MIC. The focus of this review is to describe MIC in sewer structure and the factors influencing the corrosion such as the generation of Sulfuric acid (H2SO4), Relative Humidity (RH), pH of the concrete structure and temperature. Modern developments in the design of Fiber Optical Sensors (FOSs) for observing the parameters including pH, Hydrogen Sulfide (H2S), RH and temperature will be discussed.

Structure-Function Relationships of Nanocarbon/Polymer Composites for Chemiresistive Sensing: A Review

Composites of organic compounds and inorganic nanomaterials provide novel sensing platforms for high-performance sensor applications. The combination of the attractive functionalities of nanomaterials with polymers as an organic matrix offers promising materials with tunable electrical, mechanical, and chemisensitive properties. This review mainly focuses on nanocarbon/polymer composites as chemiresistors. We first describe the structure and properties of carbon nanofillers as reinforcement agents used in the manufacture of polymer composites and the sensing mechanism of developed nanocomposites as chemiresistors. Then, the design and synthesizing methods of polymer composites based on carbon nanofillers are discussed. The electrical conductivity, mechanical properties, and the applications of different nanocarbon/polymer composites for the detection of different analytes are reviewed. Lastly, challenges and the future vision for applications of such nanocomposites are described.

Nickel nanoparticle-decorated reduced graphene oxide/WO3 nanocomposite - a promising candidate for gas sensing

We report for the first time the combination of WO3 sensing elements with a non-noble metal-carbon composite, namely a nickel metal nanoparticle-carbon composite (Ni@rGO). Previous work with WO3 had used either NiO (as part of the WO3 lattice), solely carbon, Pd-surface decorated WO3 (Pd@WO3), or Pd or Pt@carbon@WO3. We demonstrate the gas response for pure WO3, rGO/WO3 and Ni@rGO/WO3 sensing elements towards NO2 and acetone in air as well as towards CO in N2. The addition of 0.35 wt % Ni@rGO composite to WO3 enables the increase of the sensory response by more than 1.6 times for NO2 vapors. The gas response towards acetone using 0.35 wt % Ni@rGO/WO3 composite was 1.5 times greater for 3500 ppm than for 35,000 ppm acetone. For 0.35 wt % Ni@rGO/WO3 composite and CO gas, a response time (T res) of 7 min and a recovery time (T rec) of 2 min was determined.

Recent Developments in Graphene-Based Toxic Gas Sensors: A Theoretical Overview

Detecting and monitoring air-polluting gases such as carbon monoxide (CO), nitrogen oxides (NOx), and sulfur oxides (SOx) are critical, as these gases are toxic and harm the ecosystem and the human health. Therefore, it is necessary to design high-performance gas sensors for toxic gas detection. In this sense, graphene-based materials are promising for use as toxic gas sensors. In addition to experimental investigations, first-principle methods have enabled graphene-based sensor design to progress by leaps and bounds. This review presents a detailed analysis of graphene-based toxic gas sensors by using first-principle methods. The modifications made to graphene, such as decorated, defective, and doped to improve the detection of NOx, SOx, and CO toxic gases are revised and analyzed. In general, graphene decorated with transition metals, defective graphene, and doped graphene have a higher sensibility toward the toxic gases than pristine graphene. This review shows the relevance of using first-principle studies for the design of novel and efficient toxic gas sensors. The theoretical results obtained to date can greatly help experimental groups to design novel and efficient graphene-based toxic gas sensors.

Gold-carbonaceous materials based heterostructures for gas sensing applications

The carbon nanostructures such as carbon nanotubes and graphene decorated with gold nanoparticles exhibit promising gas sensing applications with enhanced sensitivity.

High-Tech and Nature-Made Nanocomposites and Their Applications in the Field of Sensors and Biosensors for Gas Detection

Gas sensors have been object of increasing attention by the scientific community in recent years. For the development of the sensing element, two major trends seem to have appeared. On one hand, the possibility of creating complex structures at the nanoscale level has given rise to ever more sensitive sensors based on metal oxides and metal-polymer combinations. On the other hand, gas biosensors have started to be developed, thanks to their intrinsic ability to be selective for the target analyte. In this review, we analyze the recent progress in both areas and underline their strength, current problems, and future perspectives.

Benchmark Investigation of Band-Gap Tunability of Monolayer Semiconductors under Hydrostatic Pressure with Focus-On Antimony

In this paper, the band-gap tunability of three monolayer semiconductors under hydrostatic pressure was intensively investigated based on first-principle simulations with a focus on monolayer antimony (Sb) as a semiconductor nanomaterial. As the benchmark study, monolayer black phosphorus (BP) and monolayer molybdenum disulfide (MoS2) were also investigated for comparison. Our calculations showed that the band-gap tunability of the monolayer Sb was much more sensitive to hydrostatic pressure than that of the monolayer BP and MoS2. Furthermore, the monolayer Sb was predicted to change from an indirect band-gap semiconductor to a conductor and to transform into a double-layer nanostructure above a critical pressure value ranging from 3 to 5 GPa. This finding opens an opportunity for nanoelectronic, flexible electronics and optoelectronic devices as well as sensors with the capabilities of deep band-gap tunability and semiconductor-to-metal transition by applying mechanical pressure.