Trends in Surgical and Beauty Masks for a Cleaner Environment

Hydrolytic degradation and biodegradation of polylactic acid electrospun fibers

Increased use of bioplastics, such as polylactic acid (PLA), helps in reducing greenhouse gas emissions, decreases energy consumption and lowers pollution, but its degradation efficiency has much room for improvement. The degradation rate of electrospun PLA fibers of varying diameters ranging from 0.15 to 1.33 μm is measured during hydrolytic degradation under different pH from 5.5 to 10, and during aerobic biodegradation in seawater supplemented with activated sewage sludge. In hydrolytic conditions, varying PLA fiber diameter had significant influence over percentage weight loss (W%L), where faster degradation was achieved for PLA fibers with smaller diameter. W%L was greatest for PLA-5 > PLA-12 > PLA-16 > PLA-20, with average W%L at 30.7%, 27.8%, 17.2% and 14.3% respectively. While different pH environment does not have a significant influence on PLA degradation, with W%L only slightly higher for basic environments. Similarly biodegradation displayed faster degradation for small diameter fibers with PLA-5 attaining the highest degree of biodegradation at 22.8% after 90 days. Hydrolytic degradation resulted in no significant structural change, while biodegradation resulted in significant hydroxyl end capping products on the PLA surface. Scanning electron microscopy (SEM) imaging of degraded PLA fibers showed a deteriorated morphology of PLA-5 and PLA-12 fibers with increased adhesion structures and irregularly shaped fibers, while a largely unmodified morphology for PLA-16 and PLA-20.

Electrosprayed Environment-Friendly Dry Triode-Like Facial Masks for Skincare

The cosmetics industry has a worrying impact on the environment, including the plastics used in products and packaging and environmentally unfriendly additives. In this study, we present an environment-friendly triode-like facial mask (TFM) that utilizes only green and degradable raw materials, nontoxic and harmless solvents, and electric energy to achieve distinct switchable directional water transport properties, avoids a wet storage environment, and reduces excessive packaging. The TFM demonstrates droplet stability when not in contact with the skin while facilitating rapid liquid transfer (15 μL) within durations of 2.8 s (dry skin) and 1.9 s (moist skin) upon contact. We elucidate the underlying mechanism behind this triode-like behavior, emphasizing the synergistic interaction of the wettability gradient, Gibbs pinning, and additional circumferential capillary force. Moreover, the TFM exhibits a reduction in the proportion of aging cells, decreasing from 44.33 to 13.75%, while simultaneously providing antibacterial and skin-beautifying effects. The TFM brings a novel experience while also holding the potential to reduce environmental pollution in the production, packaging, use, and recycling of cosmetics products.

Disposable facemask waste combustion emits neuroactive smoke particulate matter

Tremendous deposits of disposable medical facemask waste after the COVID-19 pandemic require improvement of waste management practice according to WHO report 2022, moreover facemasks are still in use around the world to protect against numerous airborne infections. Here, water-suspended smoke preparations from the combustion of disposable medical facemasks (polypropylene fibers) were collected; size, zeta potential, surface groups of smoke particulate matter were determined by dynamic light scattering, FTIR and Raman spectroscopy, and their optical properties were characterized. Neurochemical study using nerve terminals isolated from rat cortex revealed a significant decrease in the initial rate of the uptake/accumulation of excitatory and inhibitory neurotransmitters, L-[14C]glutamate and [3H]GABA, and exocytotic release, and also an increase in the extracellular level of these neurotransmitters. Fluorescent measurements revealed that ROS generation induced by hydrogen peroxide and glutamate receptor agonist kainate decreased in nerve terminals. A decrease in the membrane potential of nerve terminals and isolated neurons, the mitochondrial potential and synaptic vesicle acidification was also shown. Therefore, accidental or intentional utilization of disposable medical facemask waste by combustion results in the release of neuroactive ultrafine particulate matter to the environment, thereby contributing to plastic-associated pollution of air and water resources and neuropathology development and expansion.

Biocompatible anti-aging face mask prepared with curcumin and natural rubber with antioxidant properties

Natural rubber latex (NRL) is a biopolymer widely used in biomedical applications. In this work, we propose an innovative cosmetic face mask, combining the NRL's biological properties with curcumin (CURC), which has a high level of antioxidant activity (AA) to provide anti-aging benefits. Chemical, mechanical and morphological characterizations were performed. The CURC released by the NRL was evaluated by permeation in Franz cells. Cytotoxicity and hemolytic activity assays were performed to assess safety. The findings showed that the biological properties of CURC were preserved after loading in the NRL. About 44.2 % of CURC was released within the first six hours, and in vitro permeation showed that 9.36 % ± 0.65 was permeated over 24h. CURC-NRL was associated with a metabolic activity higher than 70 % in 3 T3 fibroblasts, cell viability ≥95 % in human dermal fibroblasts, and a hemolytic rate ≤ 2.24 % after 24 h. Furthermore, CURC-NRL maintained the mechanical characteristics (range suitable) for human skin application. We observed that CURC-NRL preserved ~20 % antioxidant activity from curcumin-free after loading in the NRL. Our results suggest that CURC-NRL has the potential to be used in the cosmetics industry, and the experimental methodology utilized in this study can be applied to different kinds of face masks.

Starch- and carboxymethyl cellulose-based films as active beauty masks with papain incorporation

This work aimed to evaluate the effects of the incorporation of papain in biopolymeric-based beauty face masks with exfoliation activity of the skin. The masks were produced by casting with starch and carboxymethyl cellulose blend (50:50 weight percentages). The macro and microstructure, protein distribution, thickness, moisture content, water contact angle, solubility matter, and mechanical properties were evaluated. Moreover, the in vitro proteolytic and exfoliation activity and storage stability were also evaluated. The films with papain had a more concise matrix which provided higher mechanical properties and lower water solubility when compared to the control film (without papain). Films with 1, 2, and 5 % of papain had enzymatic activity for casein and porcine skin substrates. The micrographs of porcine skin treated with 2 and 5 % of papain showed more difference when compared to the control sample, indicating the enzymatic exfoliation. Differently from the solution of papain, the enzyme that was immobilized in the films maintained its activity for up 90 days during the storage stability assay. Based on the physicochemical properties and proteolytic activities, the films preserved the exfoliation activity of papain and have interesting characteristics to act as beauty masks in the cosmetic field.

Natural Polymers and Cosmeceuticals for a Healthy and Circular Life: The Examples of Chitin, Chitosan, and Lignin

The present review considers the design and introduction of new cosmeceuticals in the market, based on natural polymers and active molecules extracted from biomass, in a biomimetic strategy, starting with a consideration of the biochemical mechanisms, followed by natural precision biopolymer production. After introducing the contest of nanobiotechnology in relationship with its applicability for skin contact products and classifying the currently available sustainable polymers, some widely selected abundant biopolymers (chitin, chitosan, and lignin), showing specific functionalities (anti-microbial, anti-oxidant, anti-inflammatory, etc.), are described, especially considering the possibility to combine them in nanostructured tissues, powders, and coatings for producing new cosmeceuticals, but with potentialities in other sectors, such as biomedical, personal care, and packaging sectors. After observing the general increase in market wellness and beauty forecasts over the next few years, parallelisms between nano and macro scales have suggested that nanobiotechnology application expresses the necessity to follow a better way of producing, selecting, and consuming goods that will help to transform the actual linear economy in a circular economy, based on redesigning, reducing, recycling, and reusing.

Development of Sustainable Hydrophilic Azadirachta indica Loaded PVA Nanomembranes for Cosmetic Facemask Applications

Nanofiber-based facial masks have attracted the attention of modern cosmetic applications due to their controlled drug release, biocompatibility, and better efficiency. In this work, Azadirachta indica extract (AI) incorporated electrospun polyvinyl alcohol (PVA) nanofiber membrane was prepared to obtain a sustainable and hydrophilic facial mask. The electrospun AI incorporated PVA nanofiber membranes were characterized by scanning electron microscope, Ultraviolet-visible spectroscopy (UV-Vis) drug release, water absorption analysis, 2,2-diphenyl-1-picrylhydrazyl (DPPH) scavenging, and antibacterial activity (qualitative and quantitative) at different PVA and AI concentrations. The optimized nanofiber of 376 ± 75 nm diameter was obtained at 8 wt/wt% PVA concentration and 100% AI extract. The AI nanoparticles of size range 50~250 nm in the extract were examined through a zeta sizer. The water absorption rate of ~660% and 17.24° water contact angle shows good hydrophilic nature and water absorbency of the nanofiber membrane. The UV-Vis also analyzed fast drug release of >70% in 5 min. The prepared membrane also exhibits 99.9% antibacterial activity against Staphylococcus aureus and has 79% antioxidant activity. Moreover, the membrane also had good mechanical properties (tensile strength 1.67 N, elongation 48%) and breathability (air permeability 15.24 mm/s). AI-incorporated nanofiber membrane can effectively be used for facial mask application.

A road map on synthetic strategies and applications of biodegradable polymers

Biodegradable polymers have emerged as fascinating materials due to their non-toxicity, environmentally benign nature and good mechanical strength. The toxic effects of non-biodegradable plastics paved way for the development of sustainable and biodegradable polymers. The engineering of biodegradable polymers employing various strategies like radical ring opening polymerization, enzymatic ring opening polymerization, anionic ring opening polymerization, photo-initiated radical polymerization, chemoenzymatic method, enzymatic polymerization, ring opening polymerization and coordinative ring opening polymerization have been discussed in this review. The application of biodegradable polymeric nanoparticles in the biomedical field and cosmetic industry is considered to be an emerging field of interest. However, this review mainly highlights the applications of selected biodegradable polymers like polylactic acid, poly(ε-caprolactone), polyethylene glycol, polyhydroxyalkanoates, poly(lactide-co-glycolide) and polytrimethyl carbonate in various fields like agriculture, biomedical, biosensing, food packaging, automobiles, wastewater treatment, textile and hygiene, cosmetics and electronic devices.

Chitin Nanofibril-Nanolignin Complexes as Carriers of Functional Molecules for Skin Contact Applications

Chitin nanofibrils (CN) and nanolignin (NL) were used to embed active molecules, such as vitamin E, sodium ascorbyl phosphate, lutein, nicotinamide and glycyrrhetinic acid (derived from licorice), in the design of antimicrobial, anti-inflammatory and antioxidant nanostructured chitin nanofibrils–nanolignin (CN-NL) complexes for skin contact products, thus forming CN-NL/M complexes, where M indicates the embedded functional molecule. Nano-silver was also embedded in CN-NL complexes or on chitin nanofibrils to exploit its well-known antimicrobial activity. A powdery product suitable for application was finally obtained by spray-drying the complexes co-formulated with poly(ethylene glycol). The structure and morphology of the complexes was studied using infrared spectroscopy and field emission scanning electron microscopy, while their thermal stability was investigated via thermo-gravimetry. The latter provided criteria for evaluating the suitability of the obtained complexes for subsequent demanding industrial processing, such as, for instance, incorporation into bio-based thermoplastic polymers through conventional melt extrusion. In vitro tests were carried out at different concentrations to assess skin compatibility. The obtained results provided a physical–chemical, morphological and cytocompatibility knowledge platform for the correct selection and further development of such nanomaterials, allowing them to be applied in different products. In particular, chitin nanofibrils and the CN-NL complex containing glycyrrhetinic acid can combine excellent thermal stability and skin compatibility to provide a nanostructured system potentially suitable for industrial applications.

Polylactic acid face masks: Are these the sustainable solutions in times of COVID-19 pandemic?

The global massive consumption of disposable face masks driven by the ongoing COVID-19 pandemic has emerged as a blooming disaster to both the land and marine environment that might last for generations. Growing public concerns have been raised over the management and control of this new form of plastic pollution, and one of the proposed sustainable solution is to use renewable and/or biodegradable resources to develop mask materials in order to minimize their environmental impacts. As a representative biodegradable polymer, polylactic acid (PLA) has been proposed as a promising candidate to produce non-woven face masks instead of those fossil-based polymers. To further explore the feasibility of this alternative mask material, the present work aims to study both the hydrolytic and bio-degradation behaviors of pure PLA-derived 3-ply disposable face masks at ambient temperature. Hydrolytic degradability was investigated at different pH conditions of 2, 7 and 13 with the whole piece of face mask soaked for regular timed intervals up to 8 weeks. Weight loss study showed neutral and acidic conditions had minimal effect on PLA masks, but rapid degradation occurred under basic conditions in the first week with a sharp 25% decrease in weight that slowly tapered off, coupled with solution pH dropping from 13 to 9.6. This trend was supported by mechanical property, bacterial filtration efficiency (BFE) and particulate filtration efficiency (PFE) studies. Masks soaked in basic conditions had their modulus and tensile strength dropped by more than 50% after 8 weeks where the middle layer reached 68% and 90% respectively just after 48 h, and BFE and PFE decreased by 14% and 43% respectively after 4 weeks, which was much more significant than those in neutral and acidic conditions. Base degradation was also supported by nuclear magnetic resonance (NMR) and fourier transform infrared (FTIR), which disclosed that only the middle layer undergo major degradation with random chain scission and cleavage of enol or enolate chain ends, while outer and inner layers were much less affected. Scanning electron microscopy (SEM) attributed this observation to thinner PLA fibers for the middle layer of 3-7 μm diameter, which on average is 3 times smaller. This degradation was further supported by gel permeation chromatography (GPC) which saw an increase in lower molecular weight fragment Mw ~ 800 Da with soaking duration. The biodegradation behavior was studied under OECD 301F specification in sewage sludge environment. Similarly, degradation to the middle meltblown layer was more extensive, where the average weight loss and carbon loss was 25.8% and 25.7% respectively, double that of outer/inner spunbond layer. The results showed that the face masks did not completely disintegrate after 8 weeks, but small solubilized fragments of PLA formed in the biodegradation process can be completely mineralized into carbon dioxide without generation of secondary microplastic pollution in the environment. PLA masks are therefore a slightly greener option to consider in times of a pandemic that the world was caught unprepared; however future research on masks could be geared towards a higher degradability material that fully breaks down into non-harmful components while maintaining durability, filtration and protection properties for users.

Food Loss and Food Waste for Green Cosmetics and Medical Devices for a Cleaner Planet

To stay wealthy in a world where all can live in prosperity and wellbeing, it is necessary to develop sustainable growth at net zero emissions to stop climate change, neutralizing both risks and diseases such as the COVID-19 pandemic and inequalities. Changing the worldwide use of the great quantity of food loss and waste can help to move in this direction. At this purpose, it seems useful to transform food waste into richness, extracting and using its content in natural ingredients and biopolymers to make new sustainable products and goods, including cosmetics and medical devices. Many of these ingredients are not only bioactive molecules considered of interest to produce these consumer products but are also useful in reducing the environmental footprint. The active agents may be obtained, for example, from waste material such as grapes or olive pomace, which include, among others natural polymers, phythosterols, vitamins, minerals and unsaturated fatty acids. Among the polymers, chitin and lignin have shown particular interest because biodegradable, nontoxic, skin- and environmentally friendly ingredients can be obtained at low cost from food and forestry waste, respectively. According to our experience, these polymers may be used to make nanocomposites and micro-nanoparticles that encapsulate different active ingredients, and which may be embedded into gel and non-woven tissues to realize advanced medications and smart cosmeceuticals. However, to utilize food waste in the best possible way, a better education of both industry and the consumer is considered necessary, introducing all to change the ways of production and living. The consumer has to understand the need to privilege, food, cosmetics and goods by selecting products known to be effective that also have a low release of carbon dioxide. Thus, they must pay heed to purchasing cosmetics and medical devices made by natural ingredients and packaged by biodegradable and/or reusable containers that are possibly plastic free. Conversely, the industry must try to use natural raw materials obtained from waste by changing their actual production methods. Therefore, both industry and the consumer should depart from the linear economy, which is based on taking, making, and producing waste, to move into a circular economy, which is based on redesigning, reducing, reusing and recycling. Some examples will report on the possibility to use natural polymers, including chitin and lignin, to produce new cosmeceutical tissues. These innovative tissues, to be used as biodegradable carriers for making smart cosmetics and medical devices, may be produced at zero waste to save our health and the planet biodiversity.

Characterization and Combustion Behavior of Single-Use Masks Used during COVID-19 Pandemic

This work aims to study the thermal degradation and combustion behavior of single-use masks commonly used during the COVID-19 pandemic. The sudden increase in plastic waste underlines the crucial need for a proper disposal method. Therefore, to develop a suitable method of thermal disposal, it is first necessary to identify the primary waste materials and then study their thermal and flammability behaviors using thermal analysis methods. This research focuses on the characterization of individual parts of the masks, their thermal degradation, and pyrolysis processes via FTIR, TG, and MCC analyses. FTIR analysis indicated that all three masks were made out of polypropylene sheets, while two of the ear straps contained polyamide 6. One of the samples was composed mainly of poly (ethylene terephthalate) fiber and thin inner EPDM rubber. The EPDM ear strap left the highest residue and showed the lowest flammability among all samples. The analysis of heat of combustion and thermogravimetry shows that the most heat is generated above 450 °C. Therefore, for the disposal of single-use masks to be effective, it should be carried out in the temperature range from 450 to 750 °C.

Insect Chitin-Based Nanomaterials for Innovative Cosmetics and Cosmeceuticals

Chitin and its derivatives are attracting great interest in cosmetic and cosmeceutical fields, thanks to their antioxidant and antimicrobial properties, as well as their biocompatibility and biodegradability. The classical source of chitin, crustacean waste, is no longer sustainable and fungi, a possible alternative, have not been exploited at an industrial scale yet. On the contrary, the breeding of bioconverting insects, especially of the Diptera Hermetia illucens, is becoming increasingly popular worldwide. Therefore, their exoskeletons, consisting of chitin as a major component, represent a waste stream of facilities that could be exploited for many applications. Insect chitin, indeed, suggests its application in the same fields as the crustacean biopolymer, because of its comparable commercial characteristics. This review reports several cosmetic and cosmeceutical applications based on chitin and its derivatives. In this context, chitin nanofibers and nanofibrils, produced from crustacean waste, have proved to be excellent cosmeceutical active compounds and carriers of active ingredients in personal care. Consequently, the insect-based chitin, its derivatives and their complexes with hyaluronic acid and lignin, as well as with other chitin-derived compounds, may be considered a new appropriate potential polymer to be used in cosmetic and cosmeceutical fields.

Smart and Sustainable Hair Products Based on Chitin-Derived Compounds

According to previous research studies, consumers worldwide are searching for new natural-oriented hair products that are both skin and environmentally friendly. Worldwide waste and air pollution, with the consequent environmental disasters, represent the greatest risk to human health and economy, further increased by the COVID-19 pandemic. Among others, non-biodegradable molecules are present in hair products (fossil-based additives, surfactants, etc.) and macromolecules (plastics). Plastics waste is considered the most serious problem, representing a forecast amount of 460 million tons per year by 2030, 12% of which is reused or recycled. Most plastics consumed, therefore, go to landfills and incineration, also if their recycling is considered an important driver of industrial profitability. Thus, the use of biopolymers represents an interesting alternative to produce biodegradable goods and tissues. After an introduction to the worldwide waste problem and the hair structure, the present review proposes the possibility to make biodegradable tissues that, realized by chitin nanofibrils and nano-lignin as natural polymers, may be used to produce an innovative and smart cosmetic hairline. Chitin-derived compounds are considered interesting polymers to produce non-woven tissues able to repair the hair damages provoked by the aggressiveness of both the environment and some aggressive cosmetic treatments, such as setting, bleaching, permanent waving, and oxidative coloring. The possible activity, that positively charged polymers such as chitin could have, has been speculated, interfering with the constitution and organization of the hair fibrils’ structure, which is negatively charged. The possibility of selecting biopolymers for their packaging is also discussed. Moreover, the use of these biopolymers, obtained from forestry-agro-food waste, may be of help to safeguard the further consumption of natural raw materials, necessary for future generations, also maintaining the earth’s biodiversity.

Mechanical and Air Permeability Performance of Novel Biobased Materials from Fungal Hyphae and Cellulose Fibers

Novel biobased materials from fungal hyphae and cellulose fibers have been proposed to address the increasing demand for natural materials in personal protective equipment (PPE). Materials containing commercially available kraft fibers (KF), laboratory-made highly fibrillated hemp fibers (HF) and fungal fibers (FF) obtained from fruiting bodies of lignicolous basidiomycetes growing in nature were prepared using paper production techniques and evaluated for their mechanical and air permeability properties. SEM and microscopy revealed the network structure of materials. The tensile index of materials was in the range of 8–60 Nm/g and air permeability ranged from 32–23,990 mL/min, depending on the composition of materials. HF was the key component for strength; however, the addition of FF to compositions resulted in higher air permeability. Chemical composition analysis (Fourier-transform infrared spectroscopy) revealed the presence of natural polysaccharides, mainly cellulose and chitin, as well as the appropriate elemental distribution of components C, H and N. Biodegradation potential was proven by a 30-day-long composting in substrate, which resulted in an 8–62% drop in the C/N ratio. Conclusions were drawn about the appropriateness of fungal hyphae for use in papermaking-like technologies together with cellulose fibers. Developed materials can be considered as an alternative to synthetic melt and spun-blown materials for PPE.

Preliminary Studies on an Innovative Bioactive Skin Soluble Beauty Mask Made by Combining Electrospinning and Dry Powder Impregnation

The world of cosmetics is now aiming at biobased materials which are skin-compatible and can be used to generate more sustainable beauty masks with enhanced bioactivity. This work presents, in this line of interest, the combination of two innovative technologies, namely electrospinning and dry powder impregnation, to generate biobased skin soluble electrospun pullulan carriers dry impregnated with chitin nanofibrils-nanolignin-glycyrrethinic acid (CLA) complexes, as effective biobased and skin compatible beauty masks. The scalability of the pullulan electrospun carrier and bioactive complexes impregnation were optimized and the morphology evaluated. Subsequently, skin compatibility and mask effectiveness were investigated in vitro and in vivo. The results showed that cell viability was optimal for both impregnated and neat pullulan fibers. Additionally, the CLA impregnated pullulan fibers were able to upregulate the endogenous antimicrobial molecule HBD-2. Preliminary studies in vivo indicated that the beauty mask containing the CLA complexes significantly decreased area, length and depth of forehead and crow’s feet wrinkles, and significantly increased moisturizing levels in the skin. The developed beauty mask was also seen to increase skin firmness, while it did not show skin irritation after the test. The work demonstrates that the combination of these two technologies may open new alternatives to more sustainable bioactive cosmetic products for the skin.