Microfluidic-Based Nucleic Acid Amplification Systems in Microbiology

Developing a surface acoustic wave-induced microfluidic cell lysis device for point-of-care DNA amplification

We developed a microchip device using surface acoustic waves (SAW) and sharp-edge glass microparticles to rapidly lyse low-level cell samples. This microchip features a 13-finger pair interdigital transducer (IDT) with a 30-degree focused angle, creating high-intensity acoustic beams converging 6 mm away at a 16 MHz frequency. Cell lysis is achieved through centrifugal forces acting on Candida albicans cells and glass particles within the focal area. To optimize this SAW-induced streaming, we conducted 42 pilot experiments, varying electrical power, droplet volume, glass particle size, concentration, and lysis time, resulting in optimal conditions: an electrical signal of 2.5 W, a 20 μL sample volume, glass particle size below 10 μm, concentration of 0.2 μg, and a 5-min lysis period. We successfully amplified DNA target fragments directly from the lysate, demonstrating an efficient microchip-based cell lysis method. When combined with an isothermal amplification technique, this technology holds promise for rapid point-of-care (POC) applications.

Advances on diagnosis of Helicobacter pylori infections

The association of Helicobacter pylori to several gastric diseases, such as chronic gastritis, peptic ulcer disease, and gastric cancer, and its high prevalence worldwide, raised the necessity to use methods for a proper and fast diagnosis and monitoring the pathogen eradication. Available diagnostic methods can be classified as invasive or non-invasive, and the selection of the best relies on the clinical condition of the patient, as well as on the sensitivity, specificity, and accessibility of the diagnostic test. This review summarises all diagnostic methods currently available, including the invasive methods: endoscopy, histology, culture, and molecular methods, and the rapid urease test (RUT), as well as the non-invasive methods urea breath test (UBT), serological assays, biosensors, and microfluidic devices and the stool antigen test (SAT). Moreover, it lists the diagnostic advantages and limitations, as well as the main advances for each methodology. In the end, research on the development of new diagnostic methods, such as bacteriophage-based H. pylori diagnostic tools, is also discussed.

A microfluidic chip-based multiplex PCR-reverse dot blot hybridization technique for rapid detection of enteropathogenic bacteria

Diarrhea caused by enteropathogenic bacteria is a major public health issue worldwide, especially in developing countries. In this study, a microfluidic chip-based multiplex polymerase chain reaction (PCR)-reverse dot blot hybridization technology for the rapid and simultaneous detection of 11 enteropathogenic bacteria was developed and the entire process was completed within 3-4 h. The specificity of this method was analyzed using 11 types of pure target bacterial colonies and another 7 types of pure bacterial colonies, and its sensitivity was evaluated with the serial 10-fold dilution of 11 types of pure target bacterial colonies. The detection limit of this method was as low as 10³-10² CFU/mL, and it exhibited high specificity for enteropathogenic bacteria. A total of 60 clinical diarrheal fecal samples were detected using this method, the results of which were compared with those of the conventional reference method, which resulted in a positive coincident rate of 100% and a negative coincident rate of 93.75%. Based on the findings, it could be concluded that multiplex PCR-reverse dot blot hybridization based on the microfluidic chip is a rapid, economical, sensitive, specific, and high-throughput method for detecting enteropathogenic bacteria.

Advances in Simple, Rapid, and Contamination-Free Instantaneous Nucleic Acid Devices for Pathogen Detection

Pathogenic pathogens invade the human body through various pathways, causing damage to host cells, tissues, and their functions, ultimately leading to the development of diseases and posing a threat to human health. The rapid and accurate detection of pathogenic pathogens in humans is crucial and pressing. Nucleic acid detection offers advantages such as higher sensitivity, accuracy, and specificity compared to antibody and antigen detection methods. However, conventional nucleic acid testing is time-consuming, labor-intensive, and requires sophisticated equipment and specialized medical personnel. Therefore, this review focuses on advanced nucleic acid testing systems that aim to address the issues of testing time, portability, degree of automation, and cross-contamination. These systems include extraction-free rapid nucleic acid testing, fully automated extraction, amplification, and detection, as well as fully enclosed testing and commercial nucleic acid testing equipment. Additionally, the biochemical methods used for extraction, amplification, and detection in nucleic acid testing are briefly described. We hope that this review will inspire further research and the development of more suitable extraction-free reagents and fully automated testing devices for rapid, point-of-care diagnostics.

Taking the microfluidic approach to nucleic acid analysis in forensics: Review and perspectives

Forensic laboratories are universally acknowledged as being overburdened, underfunded, and in need of improved analytical methods to expedite investigations, decrease the costs associated with nucleic acid (NA) analysis, and perform human identification (HID) at the point of need (e.g., crime scene, booking station, etc.). In response, numerous research and development (R&D) efforts have resulted in microfluidic tools that automate portions of the forensic genetic workflow, including DNA extraction, amplification, and short tandem repeat (STR) typing. By the early 2000 s, reports from the National Institute of Justice (NIJ) anticipated that microfluidic 'swab-in-profile-out' systems would be available for use at the crime scene by 2015 and the FBI's 2010 'Rapid DNA' Initiative, approved by Congress in 2017, directed this effort by guiding the development and implementation of maturing systems. At present, few fully-automated microfluidic DNA technologies are commercially available for forensic HID and their adoption by agencies interested in identification has been limited. In practice, the integration of complex laboratory processes to produce one autonomous unit, along with the highly variable nature of forensic input samples, resulted in systems that are more expensive per sample and not comparable to gold-standard identification methods in terms of sensitivity, reproducibility, and multiplex capability. This Review and Perspective provides insight into the contributing factors to this outcome; namely, we focus on the complications associated with the tremendous undertaking that is developing a sample-in-answer-out platform for HID. For context, we also describe the intricate forensic landscape that contributes to a nuanced marketplace, not easily distilled down to cases of simple supply and demand. Moving forward and considering the trade-offs associated with developing methods to compete, sometimes directly, with conventional ones, we recommend a focus shift for microfluidics developers toward the creation of innovative solutions for emerging applications in the field to increase the bandwidth of the forensic investigative toolkit. Likewise, we urge case working personnel to reframe how they conceptualize the currently available Rapid DNA tools; rather than comparing these microfluidic methods to gold-standard procedures, take advantage of their rapid and integrated modes for those situations requiring expedited identifications in an informed manner.

A novel ADA-coated UCNPs@NB sensing platform combined with nucleic acid amplification for rapid detection of Escherichia coli

In this study, we reported a novel sensing platform based on fluorescence quenching composed of alendronic acid (ADA) coated upconversion nanoparticles (UCNPs) and Nile Blue (NB) combined with polymerase chain reaction (PCR) for rapid, sensitive, and specific detection of Escherichia coli (E. coli). As a fluorescence acceptor, NB has a broad absorption band and can quench upconversion fluorescence intensity at 544 nm and 658 nm based on IFE. PCR is a double-stranded DNA (dsDNA) amplification technique with high specificity. The NB-dsDNA complex can be formed by intercalation of NB between base pairs and groove of dsDNA, leading to upconversion fluorescence recovery. The ADA-coated UCNPs@NB sensing platform achieved to detect E. coli in 1.5 h, with a lower limit of detection (33 CFU mL^-1). In addition, the sensitivity of the ADA@UCNPs-NB fluorescence sensor under different PCR cycle numbers was discussed. The results showed that the proposed sensor could effectively shorten the assay time (1.0 h) while maintaining excellent sensitivity. This study demonstrated a rapid and sensitive analytical method for detecting E. coli in chicken, providing a reference for constructing PCR fluorescence sensors.

Closed-Loop Microreactor on PCB for Ultra-Fast DNA Amplification: Design and Thermal Validation

Polymerase chain reaction (PCR) is the most common method used for nucleic acid (DNA) amplification. The development of PCR-performing microfluidic reactors (μPCRs) has been of major importance, due to their crucial role in pathogen detection applications in medical diagnostics. Closed loop (CL) is an advantageous type of μPCR, which uses a circular microchannel, thus allowing the DNA sample to pass consecutively through the different temperature zones, in order to accomplish a PCR cycle. CL μPCR offers the main advantages of the traditional continuous-flow μPCR, eliminating at the same time most of the disadvantages associated with the long serpentine microchannel. In this work, the performance of three different CL μPCRs designed for fabrication on a printed circuit board (PCB) was evaluated by a computational study in terms of the residence time in each thermal zone. A 3D heat transfer model was used to calculate the temperature distribution in the microreactor, and the residence times were extracted by this distribution. The results of the computational study suggest that for the best-performing microreactor design, a PCR of 30 cycles can be achieved in less than 3 min. Subsequently, a PCB chip was fabricated based on the design that performed best in the computational study. PCB constitutes a great substrate as it allows for integrated microheaters inside the chip, permitting at the same time low-cost, reliable, reproducible, and mass-amenable fabrication. The fabricated chip, which, at the time of this writing, is the first CL μPCR chip fabricated on a PCB, was tested by measuring the temperatures on its surface with a thermal camera. These results were then compared with the ones of the computational study, in order to evaluate the reliability of the latter. The comparison of the calculated temperatures with the measured values verifies the accuracy of the developed model of the microreactor. As a result of that, a total power consumption of 1.521 W was experimentally measured, only ~7.3% larger than the one calculated (1.417 W). Full validation of the realized CL μPCR chip will be demonstrated in future work.

Application of Microfluidics for Bacterial Identification

Bacterial infections continue to pose serious public health challenges. Though anti-bacterial therapeutics are effective remedies for treating these infections, the emergence of antibiotic resistance has imposed new challenges to treatment. Often, there is a delay in prescribing antibiotics at initial symptom presentation as it can be challenging to clinically differentiate bacterial infections from other organisms (e.g., viruses) causing infection. Moreover, bacterial infections can arise from food, water, or other sources. These challenges have demonstrated the need for rapid identification of bacteria in liquids, food, clinical spaces, and other environments. Conventional methods of bacterial identification rely on culture-based approaches which require long processing times and higher pathogen concentration thresholds. In the past few years, microfluidic devices paired with various bacterial identification methods have garnered attention for addressing the limitations of conventional methods and demonstrating feasibility for rapid bacterial identification with lower biomass thresholds. However, such culture-free methods often require integration of multiple steps from sample preparation to measurement. Research interest in using microfluidic methods for bacterial identification is growing; therefore, this review article is a summary of current advancements in this field with a focus on comparing the efficacy of polymerase chain reaction (PCR), loop-mediated isothermal amplification (LAMP), and emerging spectroscopic methods.

Development of Microfluidic Chip-Based Loop-Mediated Isothermal Amplification (LAMP) Method for Detection of Carbapenemase Producing Bacteria

The rapid and accurate diagnostic methods to identify carbapenemase-producing organisms (CPO) is of great importance for controlling the CPO infection. Herein, we have developed a microfluidic chip-based technique to detect CPO and assessed its clinical value in detecting CPO directly from blood cultures (BCs). The detection performance of the microfluidic chip-based LAMP amplification method was analyzed retrospectively on a collection of 192 isolates including molecularly characterized 108 CPO and 84 non-CPO and prospectively on a collection of 133 positive BCs with or without CPO suspicion, respectively. In the retrospective study, the microfluidic chip-based LAMP amplification method exhibited 87.5% accuracy (95% CI [82.0–91.5]), 97.7% sensitivity (95% CI [91.2–99.6]), 78.8% specificity (95% CI [69.5–86.0]), 79.6% positive predictive value (PPV) (95% CI [70.6–86.5]) and 97.6% negative predictive value (NPV) (95% CI [90.9–99.6]). Among the 192 isolates, 22 (11.5%) false-positives (FP) and 2 (1.0%) false negatives (FN) were observed. In the prospective study, the 133 routine isolates of positive BCs including 18 meropenem-resistant CPO and 115 non-CPO were assessed, and 4 FP were observed in non-CPO and CPO, respectively. The current method showed a total detection performance of 94.0% accuracy (95% CI [88.4–97.1]), 100.0% sensitivity (95% CI [73.2–100.0]), 93.2% specificity (95% CI [86.7–96.8]), 63.6% PPV (95% CI [40.8–82.0]) and 100.0% NPV (95% CI [95.8–100.0]). In summary, the microfluidic chip-based LAMP amplification method is reliable for the rapid screening and detection of CPO with high accuracy, sensitivity, and specificity, and could easily be implemented in clinical microbiology laboratories.

IMPORTANCE Rapid and accurate identification of CPO may reduce the genetic exchanges among bacteria and prevent further dissemination of carbapenemases to non-CPO. The current method had designed microfluidic chip-based LAMP amplification method for multiplex detection of carbapenemase genes and evaluated the detection performance of the newly method. The current method can rapidly screen and detect CPO with high accuracy, sensitivity, and specificity, and could easily be implemented in clinical microbiology laboratories, as this will reduce the carbapenem resistance issues worldwide.

Droplet Microfluidics for High-Resolution Virology

Microfluidics has enabled a new era of cellular and molecular assays due to the small length scales, parallelization, and the modularity of various analysis and actuation functions. Droplet microfluidics, in particular, has been instrumental in providing new tools for biology with its ability to quickly and reproducibly generate drops that act as individual reactors. A notable beneficiary of this technology has been single-cell RNA sequencing, which has revealed new heterogeneities and interactions for the fundamental unit of life. However, viruses far surpass the diversity of cellular life, affect the dynamics of all ecosystems, and are a chronic source of global health crises. Despite their impact on the world, high-throughput and high-resolution viral profiling has been difficult, with conventional methods being limited to population-level averaging, large sample volumes, and few cultivable hosts. Consequently, most viruses have not been identified and studied. Droplet microfluidics holds the potential to address many of these limitations and offers new levels of sensitivity and throughput for virology. This Feature highlights recent efforts that have applied droplet microfluidics to the detection and study of viruses, including for diagnostics, virus-host interactions, and cell-independent virus assays. In combination with traditional virology methods, droplet microfluidics should prove a potent tool toward achieving a better understanding of the most abundant biological species on Earth.

Advances in Nucleic Acid Amplification-Based Microfluidic Devices for Clinical Microbial Detection

Accurate and timely detection of infectious pathogens is urgently needed for disease treatment and control of possible outbreaks worldwide. Conventional methods for pathogen detection are usually time-consuming and labor-intensive. Novel strategies for the identification of pathogenic nucleic acids are necessary for practical application. The advent of microfluidic technology and microfluidic devices has offered advanced and miniaturized tools to rapidly screen microorganisms, improving many drawbacks of conventional nucleic acid amplification-based methods. In this review, we summarize advances in the microfluidic approach to detect pathogens based on nucleic acid amplification. We survey microfluidic platforms performing two major types of nucleic acid amplification strategies, namely, polymerase chain reaction (PCR) and isothermal nucleic acid amplification. We also provide an overview of nucleic acid amplification-based platforms including studies and commercialized products for SARS-CoV-2 detection. Technologically, we focus on the design of the microfluidic devices, the selected methods for sample preparation, nucleic acid amplification techniques, and endpoint analysis. We also compare features such as analysis time, sensitivity, and specificity of different platforms. The first section of the review discusses methods used in microfluidic devices for upstream clinical sample preparation. The second section covers the design, operation, and applications of PCR-based microfluidic devices. The third section reviews two common types of isothermal nucleic acid amplification methods (loop-mediated isothermal amplification and recombinase polymerase amplification) performed in microfluidic systems. The fourth section introduces microfluidic applications for nucleic acid amplification-based detection of SARS-CoV-2. Finally, the review concludes with the importance of full integration and quantitative analysis for clinical microbial identification.

Fabrication of Wearable PDMS Device for Rapid Detection of Nucleic Acids via Recombinase Polymerase Amplification Operated by Human Body Heat

Pathogen detection by nucleic acid amplification proved its significance during the current coronavirus disease 2019 (COVID-19) pandemic. The emergence of recombinase polymerase amplification (RPA) has enabled nucleic acid amplification in limited-resource conditions owing to the low operating temperatures around the human body. In this study, we fabricated a wearable RPA microdevice using poly(dimethylsiloxane) (PDMS), which can form soft-but tight-contact with human skin without external support during the body-heat-based reaction process. In particular, the curing agent ratio of PDMS was tuned to improve the flexibility and adhesion of the device for better contact with human skin, as well as to temporally bond the microdevice without requiring further surface modification steps. For PDMS characterization, water contact angle measurements and tests for flexibility, stretchability, bond strength, comfortability, and bendability were conducted to confirm the surface properties of the different mixing ratios of PDMS. By using human body heat, the wearable RPA microdevices were successfully applied to amplify 210 bp from Escherichia coli O157:H7 (E. coli O157:H7) and 203 bp from the DNA plasmid SARS-CoV-2 within 23 min. The limit of detection (LOD) was approximately 500 pg/reaction for genomic DNA template (E. coli O157:H7), and 600 fg/reaction for plasmid DNA template (SARS-CoV-2), based on gel electrophoresis. The wearable RPA microdevice could have a high impact on DNA amplification in instrument-free and resource-limited settings.

Isothermal Recombinase Polymerase Amplification (RPA) of E. coli gDNA in Commercially Fabricated PCB-Based Microfluidic Platforms

Printed circuit board (PCB) technology has been recently proposed as a convenient platform for seamlessly integrating electronics and microfluidics in the same substrate, thus facilitating the introduction of integrated and low-cost microfluidic devices to the market, thanks to the inherent upscaling potential of the PCB industry. Herein, a microfluidic chip, encompassing on PCB both a meandering microchannel and microheaters to accommodate recombinase polymerase amplification (RPA), is designed and commercially fabricated for the first time on PCB. The developed microchip is validated for RPA-based amplification of two E. coli target genes compared to a conventional thermocycler. The RPA performance of the PCB microchip was found to be well-comparable to that of a thermocycler yet with a remarkably lower power consumption (0.6 W). This microchip is intended for seamless integration with biosensors in the same PCB substrate for the development of a point-of-care (POC) molecular diagnostics platform.

Use of some cost-effective technologies for a routine clinical pathology laboratory

Classically, the need for highly sophisticated instruments with important economic costs has been a major limiting factor for clinical pathology laboratories, especially in developing countries. With the aim of making clinical pathology more accessible, a wide variety of free or economical technologies have been developed worldwide in the last few years. 3D printing and Arduino approaches can provide up to 94% economical savings in hardware and instrumentation in comparison to commercial alternatives. The vast selection of point-of-care-tests (POCT) currently available also limits the need for specific instruments or personnel, as they can be used almost anywhere and by anyone. Lastly, there are dozens of free and libre digital tools available in health informatics. This review provides an overview of the state-of-the-art on cost-effective alternatives with applications in routine clinical pathology laboratories. In this context, a variety of technologies including 3D printing and Arduino, lateral flow assays, plasmonic biosensors, and microfluidics, as well as laboratory information systems, are discussed. This review aims to serve as an introduction to different technologies that can make clinical pathology more accessible and, therefore, contribute to achieve universal health coverage.

Micro and Nanoscale Technologies for Diagnosis of Viral Infections

Viral infection is one of the leading causes of mortality worldwide. The growth of globalization significantly increases the risk of virus spreading, making it a global threat to future public health. In particular, the ongoing coronavirus disease 2019 (COVID-19) pandemic outbreak emphasizes the importance of devices and methods for rapid, sensitive, and cost-effective diagnosis of viral infections in the early stages by which their quick and global spread can be controlled. Micro and nanoscale technologies have attracted tremendous attention in recent years for a variety of medical and biological applications, especially in developing diagnostic platforms for rapid and accurate detection of viral diseases. This review addresses advances of microneedles, microchip-based integrated platforms, and nano- and microparticles for sampling, sample processing, enrichment, amplification, and detection of viral particles and antigens related to the diagnosis of viral diseases. Additionally, methods for the fabrication of microchip-based devices and commercially used devices are described. Finally, challenges and prospects on the development of micro and nanotechnologies for the early diagnosis of viral diseases are highlighted.

Multiple species-specific molecular markers using nanofluidic array as a tool to detect prey DNA from carnivore scats

Large carnivore feeding ecology plays a crucial role for management and conservation for predators and their prey. One of the keys to this kind of research is to identify the species composition in the predator diet, for example, prey determination from scat content. DNA-based methods applied to detect prey in predators' scats are viable alternatives to traditional macroscopic approaches, showing an increased reliability and higher prey detection rate. Here, we developed a molecular method for prey species identification in wolf (Canis lupus) scats using multiple species-specific marker loci on the cytochrome b gene for 18 target species. The final panel consisted of 80 assays, with a minimum of four markers per target species, and that amplified specifically when using a high-throughput Nanofluidic array technology (Fluidigm Inc.). As a practical example, we applied the method to identify target prey species DNA in 80 wolf scats collected in Sweden. Depending on the number of amplifying markers required to obtain a positive species call in a scat, the success in determining at least one prey species from the scats ranged from 44% to 92%. Although we highlight the need to evaluate the optimal number of markers for sensitive target species detection, the developed method is a fast and cost-efficient tool for prey identification in wolf scats and it also has the potential to be further developed and applied to other areas and large carnivores as well.

Recent Advances in Microfluidic Devices for Contamination Detection and Quality Inspection of Milk

Milk is a necessity for human life. However, it is susceptible to contamination and adulteration. Microfluidic analysis devices have attracted significant attention for the high-throughput quality inspection and contaminant analysis of milk samples in recent years. This review describes the major proposals presented in the literature for the pretreatment, contaminant detection, and quality inspection of milk samples using microfluidic lab-on-a-chip and lab-on-paper platforms in the past five years. The review focuses on the sample separation, sample extraction, and sample preconcentration/amplification steps of the pretreatment process and the determination of aflatoxins, antibiotics, drugs, melamine, and foodborne pathogens in the detection process. Recent proposals for the general quality inspection of milk samples, including the viscosity and presence of adulteration, are also discussed. The review concludes with a brief perspective on the challenges facing the future development of microfluidic devices for the analysis of milk samples in the coming years.

Rapid and simple single-chamber nucleic acid detection system prepared through nature-inspired surface engineering

Background: Nucleic acid (NA)-based diagnostics enable a rapid response to various diseases, but current techniques often require multiple labor-intensive steps, which is a major obstacle to successful translation to a clinical setting.

Methods: We report on a surface-engineered single-chamber device for NA extraction and in situ amplification without sample transfer. Our system has two reaction sites: a NA extraction chamber whose surface is patterned with micropillars and a reaction chamber filled with reagents for in situ polymerase-based NA amplification. These two sites are integrated in a single microfluidic device; we applied plastic injection molding for cost-effective, mass-production of the designed device. The micropillars were chemically activated via a nature-inspired silica coating to possess a specific affinity to NA.

Results: As a proof-of-concept, a colorimetric pH indicator was coupled to the on-chip analysis of NA for the rapid and convenient detection of pathogens. The NA enrichment efficiency was dependent on the lysate incubation time, as diffusion controls the NA contact with the engineered surface. We could detect down to 1×10³ CFU by the naked eye within one hour of the total assay time.

Conclusion: We anticipate that the surface engineering technique for NA enrichment could be easily integrated as a part of various types of microfluidic chips for rapid and convenient nucleic acid-based diagnostics.

Review of Microfluidic Methods for Cellular Lysis

Cell lysis is a process in which the outer cell membrane is broken to release intracellular constituents in a way that important information about the DNA or RNA of an organism can be obtained. This article is a thorough review of reported methods for the achievement of effective cellular boundaries disintegration, together with their technological peculiarities and instrumental requirements. The different approaches are summarized in six categories: chemical, mechanical, electrical methods, thermal, laser, and other lysis methods. Based on the results derived from each of the investigated reports, we outline the advantages and disadvantages of those techniques. Although the choice of a suitable method is highly dependent on the particular requirements of the specific scientific problem, we conclude with a concise table where the benefits of every approach are compared, based on criteria such as cost, efficiency, and difficulty.

One-Step Reverse-Transcription Recombinase Polymerase Amplification Using Lateral Flow Strips for the Detection of Coxsackievirus A6

Hand, foot, and mouth disease (HFMD) is a common infectious disease affecting mainly children under 5 years of age. Coxsackievirus A6 (CVA-6), a major causative pathogen of HFMD, has caused outbreaks in recent years. Currently, no effective vaccine or antiviral treatments are available. In this study, one-step reverse-transcription recombinase polymerase amplification (RT-RPA), combined with a disposable lateral flow strip (LFS) assay, was developed to detect CVA-6. This assay can be performed in less than 35 min at 37°C without expensive instruments, and the result can be observed directly with the naked eye. The sensitivity of the RT-RPA-LFS was 10 copies per reaction, which was comparable to that of the conventional real-time quantitative polymerase chain reaction (qPCR) assays. Moreover, the assay specificity was 100%. The clinical performance of the RT-RPA-LFS assay was evaluated using 142 clinical samples, and the coincidence rate between RT-RPA-LFS and qPCR was 100%. Therefore, our RT-RPA-LFS assay provides a simple and rapid approach for point-of-care CVA-6 diagnosis.

Microfluidic-based virus detection methods for respiratory diseases

With the recent SARS-CoV-2 outbreak, the importance of rapid and direct detection of respiratory disease viruses has been well recognized. The detection of these viruses with novel technologies is vital in timely prevention and treatment strategies for epidemics and pandemics. Respiratory viruses can be detected from saliva, swab samples, nasal fluid, and blood, and collected samples can be analyzed by various techniques. Conventional methods for virus detection are based on techniques relying on cell culture, antigen-antibody interactions, and nucleic acids. However, these methods require trained personnel as well as expensive equipment. Microfluidic technologies, on the other hand, are one of the most accurate and specific methods to directly detect respiratory tract viruses. During viral infections, the production of detectable amounts of relevant antibodies takes a few days to weeks, hampering the aim of prevention. Alternatively, nucleic acid-based methods can directly detect the virus-specific RNA or DNA region, even before the immune response. There are numerous methods to detect respiratory viruses, but direct detection techniques have higher specificity and sensitivity than other techniques. This review aims to summarize the methods and technologies developed for microfluidic-based direct detection of viruses that cause respiratory infection using different detection techniques. Microfluidics enables the use of minimal sample volumes and thereby leading to a time, cost, and labor effective operation. Microfluidic-based detection technologies provide affordable, portable, rapid, and sensitive analysis of intact virus or virus genetic material, which is very important in pandemic and epidemic events to control outbreaks with an effective diagnosis.

Visualization and Measurements of Blood Cells Flowing in Microfluidic Systems and Blood Rheology: A Personalized Medicine Perspective

Hemorheological alterations in the majority of metabolic diseases are always connected with blood rheology disturbances, such as the increase of blood and plasma viscosity, cell aggregation enhancement, and reduction of the red blood cells (RBCs) deformability. Thus, the visualizations and measurements of blood cells deformability flowing in microfluidic devices (point-of-care devices) can provide vital information to diagnose early symptoms of blood diseases and consequently to be used as a fast clinical tool for early detection of biomarkers. For instance, RBCs rigidity has been correlated with myocardial infarction, diabetes mellitus, hypertension, among other blood diseases. In order to better understand the blood cells behavior in microfluidic devices, rheological properties analysis is gaining interest by the biomedical committee, since it is strongly dependent on the interactions and mechanical cells proprieties. In addition, the development of blood analogue fluids capable of reproducing the rheological properties of blood and mimic the RBCs behavior at in vitro conditions is crucial for the design, performance and optimization of the microfluidic devices frequently used for personalized medicine. By combining the unique features of the hemorheology and microfluidic technology for single-cell analysis, valuable advances in personalized medicine for new treatments and diagnosis approach can be achieved.

Microfluidics for the rapid detection of Staphylococcus aureus using antibody-coated microspheres

Staphylococcus aureus is a common foodborne pathogenic microorganism which can cause food poisoning and it is pathogenic to both humans and animals. Therefore, rapid detection of S. aureus infection is of great significance. In this study, a microfluidic platform was introduced to detect S. aureus by fluorescence labeling method and a self-made microfluidic chip, which has immune spheres were used to study the effect of capturing S. aureus. Through this experiment, we found that the platform can be used for microbial culture, and S. aureus antibody coated on the diameter of 50 ~ 90 μm microspheres for detection. On the premise of optimizing the sample flow rate and detection time, the bacterial detection was quantitatively monitored. Results showed that our platform can detect S. aureus at injection rate of 5 μL·min⁻¹ reacted for 4 min and the detection limit of bacteria is 1.5 × 10¹ CFU/μL. However, the detection time of traditional method is 24 hs to 72 hs, and the operation is complex and cumbersome. These findings indicated that the microfluidic chip in this study is portable, sensitive, and accurate, laying a good foundation for further research on the application of rapid bacterial detection platform.

Advances in automated techniques to identify Acinetobacter calcoaceticus-Acinetobacter baumannii complex

Acinetobacter species, particularly those within Acinetobacter calcoaceticus-A. baumannii complex (ACB complex), have emerged as clinically relevant pathogens in hospital environments worldwide. Early and quick detection and identification of Acinetobacter infections is challenging, and traditional culture and biochemical methods may not achieve adequate levels of speciation. Moreover, currently available techniques to identify and differentiate closely related Acinetobacter species are insufficient. The objective of this review is to recapitulate the current evolution in phenotypic and automated techniques used to identify the ACB complex. Compared with other automated or semiautomated systems of bacterial identification, matrix-assisted laser desorption-ionization time-of-flight mass spectrometry (MALDI-TOF MS) demonstrates a high level of Acinetobacter species identification and discrimination, including newly discovered species A. seifertii and A. dijkshoorniae.

Optimization of on-bead emulsion polymerase chain reaction based on single particle analysis

Emulsion polymerase chain reaction (ePCR) enables parallel amplification of millions of different DNA molecules while avoiding bias and chimeric byproducts, essential criteria for applications including next generation sequencing, aptamer selection, and protein-DNA interaction studies. Despite these advantages, ePCR remains underused due to the lack of optimal starting conditions, straightforward methods to evaluate success, and guidelines for tuning the reaction. This knowledge has been elusive for bulk emulsion generation methods, such as stirring and vortexing, the only methods that can emulsify libraries of ≥10⁸ sequences within minutes, because these emulsions have not been characterized in ways that preserve the heterogeneity that defines successful ePCR. Our study quantifies the outcome of ePCR from conditions specified in the literature using single particle analysis, which preserves this heterogeneity. We combine ePCR with magnetic microbeads and quantify the amplification yield via qPCR and the proportion of clonal and saturated beads via flow cytometry. Our single particle level analysis of thousands of beads resolves two key criteria that define the success of ePCR: 1) whether the target fraction of 20% clonal beads predicted by the Poisson distribution is achieved, and 2) whether those beads are partially or maximally covered by amplified DNA. We found that among the two concentrations of polymerase tested, only the higher one, which is 20-fold more than the concentration recommended for conventional PCR, could yield sufficient PCR products. Dramatic increases in the concentrations of reverse primer and nucleotides recommended in literature gave no measurable change in outcome. We thus provide evidence-based starting conditions for effective and economical ePCR for real DNA libraries and a straightforward workflow for evaluating the success of tuning ePCR prior to downstream applications.

Core-Shell Beads as Microreactors for Phylogrouping of E. coli Strains

Multiplex polymerase chain reaction (PCR) is an effective tool for simultaneous detection of target genes. Nevertheless, their use has been restricted due to the intrinsic interference between primer pairs. Performing several single PCRs in an array format instead of a multiplex PCR is a simple way to overcome this obstacle. However, there are still major technical challenges in designing a new generation of single PCR microreactors with a small sample volume, rapid thermal cycling, and no evaporation during amplification. We report a simple and robust core-shell bead array for a series of single amplifications. Four core-shell beads with a polymer coating and PCR mixture were synthesized using liquid marble formation and subsequent photo polymerization. Each bead can detect one target gene. We constructed a customised system for thermal cycling of these core-shell beads. Phylogrouping of the E. coli strains was carried out based on the fluorescent signal of the core-shell beads. This platform can be a promising alternative for multiplex nucleic acid analyses due to its simplicity and high throughput. The platform reported here also reduces the cycling time and avoids evaporation as well as contamination of the sample during the amplification process.

Current Progression: Application of High-Throughput Sequencing Technique in Space Microbiology

During a spaceflight, astronauts need to live in a spacecraft on orbit for a long time, and the relationship between humans and microorganisms in the closed environment of space is not the same as on the ground. The dynamic study of microorganisms in confined space shows that with the extension of the isolation time, harmful bacteria gradually accumulate. Monitoring and controlling microbial pollution in a confined environment system are very important for crew health and the sustainable operation of a space life support system. Culture-based assays have been used traditionally to assess the microbial loads in a spacecraft, and uncultured-based techniques are already under way according to the NASA global exploration roadmap. High-throughput sequencing technology has been used generally to study the communities of the environment and human on the ground and shows its broad prospects applied onboard. We here review the recent application of high-throughput sequencing on space microbiology and analyze its feasibility and potential as an on-orbit detection technology.

Heat and pressure-resistant room temperature irreversible sealing of hybrid PDMS–thermoplastic microfluidic devices via carbon–nitrogen covalent bonding and its application in a continuous-flow polymerase chain reaction

In this study, we have introduced a facile room-temperature strategy for irreversibly sealing polydimethylsiloxane to various thermoplastics using (3-aminopropyl)triethoxysilane (APTES) and [2-(3,4-epoxycyclohexyl)ethyl]trimethoxysilane (ECTMS).

Centrifugal microfluidic lab-on-a-chip system with automated sample lysis, DNA amplification and microarray hybridization for identification of enterohemorrhagic Escherichia coli culture isolates

Automated workflow that starts with a colony isolate and ends with a fluorescence signal on a DNA microarray.

Microfluidic Array Chip for Parallel Detection of Waterborne Bacteria

The polymerase chain reaction (PCR) is a robust technique used to make multiple copies of a segment of DNA. However, the available PCR platforms require elaborate and time-consuming operations or costly instruments, hindering their application. Herein, we introduce a sandwiched glass-polydimethylsiloxane (PDMS)-glass microchip containing an array of reactors for the real-time PCR-based detection of multiple waterborne bacteria. The PCR solution was loaded into the array of reactors in a single step utilising capillary filling, eliminating the need for pumps, valves, and liquid handling instruments. Issues of generating and trapping bubbles during the loading chip step were addressed by creating smooth internal reactor surfaces. Triton X-100 was used to enhance PCR compatibility in the chip by minimising the nonspecific adsorption of enzymes. A custom-made real-time PCR instrument was also fabricated to provide thermal cycling to the array chip. The microfluidic device was successfully demonstrated for microbial faecal source tracking (MST) in water.

Recent Progress in Lab-On-a-Chip Systems for the Monitoring of Metabolites for Mammalian and Microbial Cell Research

Lab-on-a-chip sensing technologies have changed how cell biology research is conducted. This review summarises the progress in the lab-on-a-chip devices implemented for the detection of cellular metabolites. The review is divided into two subsections according to the methods used for the metabolite detection. Each section includes a table which summarises the relevant literature and also elaborates the advantages of, and the challenges faced with that particular method. The review continues with a section discussing the achievements attained due to using lab-on-a-chip devices within the specific context. Finally, a concluding section summarises what is to be resolved and discusses the future perspectives.