Developments in the Application of Nanomaterials for Water Treatment and Their Impact on the Environment

A comprehensive review on removal of pollutants from wastewater through microbial nanobiotechnology -based solutions

Increasing wastewater pollution owing to the briskly rising human population, rapid industrialization, and fast urbanization has necessitated highly efficient wastewater treatment technologies. Although several methods of wastewater treatments are in practice, expensiveness, use of noxious chemicals, generation of unsafe by-products, and longer time consumption restrain their use to a great extent. Over the last few decades, nanotechnological wastewater treatment approaches have received widespread recognition globally. Microbially fabricated nanoparticles reduce the utilization of reducing, capping, and stabilizing agents, and exhibit higher adsorptive and catalytic efficiency than chemically synthesized nanomaterials. The present review comprehensively summarizes the applications of microbial nanotechnology in the removal of a wide range of noxious wastewater pollutants. Moreover, prospects and challenges associated with the integration of nanotechnology with other biological treatment technologies including algal-membrane bioreactor, aerobic digestion, microbial fuel cells, and microbial nanofiber webs have also been briefly discussed.

Prevention is better than a cure: A 'zero residual nanoadsorbent toxicity' downstream from its effluent exit point

Here, we offer thoughts concerning a 'zero residual nanoadsorbent toxicity' environmental policy which we strongly advocate. Our discussions in support of this policy are based on the adage 'Prevention is better than cure'. Besides emphasizing the need for strict regulations (regional and international), research and development avenues are highlighted for the technology that can achieve 'zero tolerance' for residual nanoadsorbent levels escaping and building up in receiving ecosystems. We do not oppose nanoadsorbents. On the contrary, their water and wastewater purification potentials are well recognized. However, they should not be permitted to translocate downstream from the exit point of a final effluent.

Carbon based nanocomposites, surface functionalization as a promising material for VOCs (volatile organic compounds) treatment

Urban residential and industrial growth development affects sustainable and healthful indoor environments. Environmental issues are a global problem. The deterioration of indoor air quality has prompted the creation of several air cleansing techniques. This review explains how carbon-based materials have influenced the development of air purification systems using photocatalysis. These carbon-based materials offer unique properties and advantages in VOC removal processes. Biochar, produced from biomass pyrolysis, provides an environmentally sustainable solution with its porous structure and carbon-rich composition. Carbon quantum dots, with their quantum confinement effects and tunable surface properties, show promise in VOC sensing and removal applications. Polymers incorporating reduced graphene oxide demonstrate enhanced adsorption capabilities owing to the synergistic effects of graphene and polymer matrices. Activated carbon fibers, characterized by their high aspect ratio and interconnected porosity, provide efficient VOC removal with rapid kinetics. With their unique electronic and structural properties, graphitic carbon nitrides offer opportunities for photocatalytic degradation of VOCs under visible light. Catalysts integrated with MXene, a two-dimensional nanomaterial, exhibit enhanced catalytic activity for VOC oxidation reactions. Using various carbon-based materials in VOC removal showcases the versatility and effectiveness of carbon-based approaches in addressing environmental challenges associated with indoor air pollution. Metal-organic-framework materials are carbon-based compounds. It examines the correlation between VOC mineralization and specific characteristics of carbon materials, including surface area, adsorption capability, surface functional groups, and optoelectronic properties. Discussions include the basics of PCO, variables influencing how well catalysts degrade, and degradation mechanisms. It explores how technology will improve in the future to advance studies on healthy and sustainable indoor air quality.

Progress in the Sustainable Development of Biobased (Nano)materials for Application in Water Treatment Technologies

Water pollution remains a widespread problem, affecting the health and wellbeing of people around the globe. While current advancements in wastewater treatment and desalination show promise, there are still challenges that need to be overcome to make these technologies commercially viable. Nanotechnology plays a pivotal role in water purification and desalination processes today. However, the release of nanoparticles (NPs) into the environment without proper safeguards can lead to both physical and chemical toxicity. Moreover, many methods of NP synthesis are expensive and not environmentally sustainable. The utilization of biomass as a source for the production of NPs has the potential to mitigate issues pertaining to cost, sustainability, and pollution. The utilization of biobased nanomaterials (bio-NMs) sourced from biomass has garnered attention in the field of water purification due to their cost-effectiveness, biocompatibility, and biodegradability. Several research studies have been conducted to efficiently produce NPs (both inorganic and organic) from biomass for applications in wastewater treatment. Biosynthesized materials such as zinc oxide NPs, phytogenic magnetic NPs, biopolymer-coated metal NPs, cellulose nanocrystals, and silver NPs, among others, have demonstrated efficacy in enhancing the process of water purification. The utilization of environmentally friendly NPs presents a viable option for enhancing the efficiency and sustainability of water pollution eradication. The present review delves into the topic of biomass, its origins, and the methods by which it can be transformed into NPs utilizing an environmentally sustainable approach. The present study will examine the utilization of greener NPs in contemporary wastewater and desalination technologies.

Synthesis and characterization of polysiphonia/cerium oxide/nickel oxide nanocomposites for the removal of toxins from contaminated water and antibacterial potential

Due to massive industrial development, organic and inorganic wastes are very common in most industrial effluents from the pharmaceutical industry. Even in low concentrations, they are very dangerous and harmful to humans and other living organisms. Antibiotics are frequently detected in surface waters, in soil, in wastewater from sewage treatment plants, and even in drinking water. The major environmental threat they pose has prompted to search for effective and environmentally friendly means of eliminating these toxins. The biogenic synthesis of nanomaterials using natural herbal extracts has attracted considerable attention due to their low-cost, environmentally friendly and non-toxic nature, and as a reversal of various physical and chemical processes. The ceria nanoparticles (CeO2 NPs), nickel oxide nanoparticles (NiO NPs), and CeO2/NiO nanocomposites (CeO2/NiO NCS) were successfully prepared by simple biosynthetic routes using Polysiphonia urceolata algae extract as green surfactants and tested for toxic ofloxacin removal efficiency. The formed nanostructures were identified and characterized by various microscopic (FESEM-EDX, TEM, XRD, BET, and XPS) and spectroscopic (UV-Vis, FTIR, and TGA) methods. The adsorption/desorption of ofloxacin (OFX) on the surface of the nanomaterials was investigated under optimized conditions (initial dose 20 mg/L, agitation speed 250 rpm, pH 12, adsorbent dose 0.5 mg/L, and contact time 120 min). The removal efficiencies were 78%, 86%, and 94% for CeO2 NPs, NiO NPs and CeO2/NiO NCS, respectively, where OFX removal was found to be spontaneous, followed by Freundlich isotherm and pseudo-second order kinetic reaction model. The OFX adsorption mechanism on the nanomaterials involved the surface complexation via specific electrostatic attraction and H-bonding. The biogenic nanomaterials were also tested for their antibacterial activity against Escherichia coli, Pseudomonas aeruginosa, Staphylococcus epidermidis and Staphylococcus aureus. The CeO2/NiO NCS exhibited the highest antibacterial activity with zone of inhibition (31.12 ± 0.59 mm) against S. epidermidis, followed by CeO2NPs and NiONPs with zones of inhibition (25.53 ± 1.2 mm) and (21.42 ± 0.6 mm) against P. aeruginosa and S. epidermidis, respectively. This study demonstrated the efficiency of the synthesized nanomaterials in removing toxins such as OFX from contaminated water and can serve as potential antibacterial and antioxidant agents. Notably, the heterogeneous nanomaterials demonstrated remarkable stability across a broad pH range, promising reusability and indicated tremendous potential of waste biomass reduction and OFX effluent treatment.

Effective treatment of petroleum oil-contaminated wastewater using activated sludge modified with magnetite/silicon nanocomposite

The study aimed to optimize the treatment of oil refinery-contaminated wastewater through modification of the well-established activated sludge process with new nanocomposite (NC) materials to produce high-quality treated effluents for potential reuse. Refinery wastewater samples were collected from one of the major oil refineries, Alexandria, Egypt, where the operation, performance, and efficiency of the current activated sludge (AS) unit were evaluated for 6 consecutive months. Two AS bench scale PVC basins were constructed. Magnetite nanoparticles (Fe3O4 NPs) and magnetite silica (Fe3O4/silica) nanocomposite (NC) were prepared and characterized. Bioremediation trials were carried out in a sequential batch mode using Fe3O4/silica NC-modified AS and control (unmodified AS). The proposed treatment produced high-quality effluents in a very short time (2 h) despite the very high initial pollutant concentration accompanied with a reduction in the produced sludge. The highest removal of TSS, TDS, BOD, COD, and OG from raw industrial wastewater recorded 78.33, 3.6, 87.65, 85.17, and 92.92% compared to 55.3, 12.6, 50.0, 40.22, and 56.84%, respectively, achieved by the unmodified AS unit. The results confirmed that integration of the AS treatment with nanomaterial composite is highly effective, promising, and economic for the treatment of highly toxic and complicated industrial wastewater such as petroleum refinery effluents.

Design, Synthesis, and Evaluation of Novel Magnetic Nanoparticles Combined with Thiophene Derivatives for the Removal of Cr(VI) from an Aqueous Solution

Most heavy metals are harmful to human health and the environment, even at extremely low concentrations. In natural waters, they are usually found only in trace amounts. Researchers are paying great attention to nanotechnology and nanomaterials as viable solutions to the problem of water pollution. This research focuses on the synthesis of organic thiophene derivatives that can be used as grafted ligands on the surface of silica-coated iron oxide nanoparticles to remove Cr(VI) chromium ions from water. The Vilsmeier-Haack reaction allows the formation of aldehyde groups in thiophene derivatives, and the resulting products were characterized by the FT-IR, NMR, and GC-MS. Schiff base is used as a binder between organic compounds and nanoparticles by the reaction of aldehyde groups in thiophene derivatives and amine groups on the surface of coated iron oxide nanoparticles. Schiff base functionalized Fe3O4 composites (MNPs@SiO2-SB-THCA) and (MNPs@SiO2-SB-THCTA) were successfully synthesized by homogeneous and heterogeneous methods and characterized by a combination of FT-IR, transmission electron microscopy, X-ray photoelectron spectroscopy, and thermogravimetric analysis. The adsorption studies, kinetic modeling, adsorption isotherms, and thermodynamics of the two materials, MNPs@SiO2-SB-THCA and MNPs@SiO2-SB-THCTA, were investigated for the removal of Cr(VI) from water at room temperature and at 50 mg/L. The high adsorption capacity at pH 6 for MNPs@SiO2-SB-THCTA was 15.53 mg/g, and for MNPs@SiO2-SB-THCA, it was 14.31 mg/g.

Biofilm-mediated infections by multidrug-resistant microbes: a comprehensive exploration and forward perspectives

A biofilm is a collection of microorganisms organized in a matrix of extracellular polymeric material. Biofilms consist of microbial cells that attach to both surfaces and each other, whether they are living or non-living. These microbial biofilms can lead to hospital-acquired infections and are generally detrimental. They possess the ability to resist the human immune system and antibiotics. The National Institute of Health (NIH) states that biofilm formation is associated with 65% of all microbial illnesses and 80% of chronic illnesses. Additionally, non-device-related microbial biofilm infections include conditions like cystic fibrosis, otitis media, infective endocarditis, and chronic inflammatory disorders. This review aims to provide an overview of research on chronic infections caused by microbial biofilms, methods used for biofilm detection, recent approaches to combat biofilms, and future perspectives, including the development of innovative antimicrobial strategies such as antimicrobial peptides, bacteriophages, and agents that disrupt biofilms.

Adsorption of contaminants by nanomaterials synthesized by green and conventional routes: a critical review

Nanomaterials, due to their large surface area and selectivity, have stood out as an alternative for the adsorption of contaminants from water and effluents. Synthesized from green or traditional protocols, the main advantages and disadvantages of green nanomaterials are the elimination of the use of toxic chemicals and difficulty of reproducing the preparation of nanomaterials, respectively, while traditional nanomaterials have the main advantage of being able to prepare nanomaterials with well-defined morphological properties and the disadvantage of using potentially toxic chemicals. Thus, based on the particularities of green and conventional nanomaterials, this review aims to fill a gap in the literature on the comparison of the synthesis, morphology, and application of these nanomaterials in the adsorption of contaminants in water. Focusing on the adsorption of heavy metals, pesticides, pharmaceuticals, dyes, polyaromatic hydrocarbons, and phenol derivatives in water, for the first time, a review article explored and compared how chemical and morphological changes in nanoadsorbents synthesized by green and conventional protocols affect performance in the adsorption of contaminants in water. Despite advances in the area, there is still a lack of review articles on the topic.

Green Synthesis of Silver Nanoparticles using Morinda citrifolia Linn LeafExtract and its Antioxidant, Antibacterial and Anticancer Potential

INTRODUCTION

Nanomedicine has emerged as a revolutionary regimen for moderating communicable as well as non-communicable diseases.

PURPOSE

This study demonstrated the phytosynthesis of silver nanoparticles using M. citrifolia leaf extract (MC-AgNPs) and their in vitro antioxidant, antibacterial and anticancer potential.

MATERIALS AND METHODS

The Biosynthesis of MC-AgNPs was studied by spectroscopy and characterized by SEM, TEM, XRD and FTIR analysis. The antibacterial activity was checked by minimum inhibition concentration assay. The HeLa and MCF-7 cancer cell lines were used to explore the cytotoxicity and genotoxicity activity of biogenic MC-AgNPs.

RESULTS

The free radical scavenging potential of MC-AgNPs was studied by in vitro DPPH and ABTS assays, which confirmed significant radical scavenging activity in a dose-dependent manner with IC50 of 17.70 ± 0.36 μg/mL for DPPH and 13.37 ± 3.15 μg/mL for ABTS radicals. The bactericidal effects of MC-AgNPs confirmed by MIC showed 0.1 mg/mL concentration of MC-AgNPs with greater sensitivity for E.coli (93.33 ± 0.89), followed by K. pneumoniae (90.99 ± 0.57), S. aureus (87.26 ± 2.80) and P. aeruginosa strains (44.68 ± 0.73). The cytotoxicity results depicted strong dose and timedependent toxicity of biogenic MC-AgNPs against cancer cell lines fifty percent inhibitory concentration MC-AgNPs against HeLa cells were 13.56 ± 1.22 μg/mL after 24h and 5.57 ± 0.12 μg/mL after 48 h exposure, likewise 16.86 ± 0.88 μg/mL and 11.60 ± 0.97 μg/mL respectively for MCF-7 cells.

CONCLUSIONS

The present study revealed the green synthesis of silver nanoparticles using M. citrifolia and their significant antioxidant, antibacterial and anticancer activities.

Sustainable Preparation of Graphene Quantum Dots from Leaves of Date Palm Tree

The date palm (Phoenix dactylifera), a subtropical and tropical tree, included in the family Palmae (Arecaceae) is one of the oldest cultivated plants of mankind. Date palm is a major agricultural product in the semi-arid and arid areas of the world, particularly in Arab countries. These trees generate high quantities of agricultural waste in the form of dry leaves, seeds, etc. In this study, dried date palm leaves were used as green precursors for synthesizing graphene quantum dots (GQDs). This work reported the preparation of GQDs using two different sustainable methods. GQD-1 was developed using a simple, hydrothermal technique at 200 °C for 12 h in water, with no requirement of reducing or passivizing agents or organic solvents. GQD-2 was prepared using a hydrothermal technique at 200 °C for 12 h in water, with the usage of just distilled water and absolute ethanol. The compositional analysis of the leaf extract was performed, along with the morphological, compositional, and optical examination of the sustainably developed GQDs. The characterization results confirmed the successful formation of GQDs, with average sizes ranging from 3.5 to 8 nm. This study helps to obtain GQDs in an economical, eco-friendly, and biocompatible manner and can assist in large-scale production and in recycling date palm tree waste products from Middle East countries into value-added products.

Piezoelectric materials and techniques for environmental pollution remediation

With the rapid development of industrialization and agriculture, a series of critical imminent environmental problems and water pollution have caught wide attention from the public and society. Piezoelectric catalysis technology with piezoelectric materials is a green and environmental method that can efficiently improve the separation of electron-hole pairs, then generating the active substances such as OH, H₂O₂ and O₂^-, which can degrade water pollutants. Therefore, we firstly surveyed the piezoelectric catalysis in piezoelectric materials and systematically concluded and emphasized the relationship between piezoelectric materials and the piezoelectric catalytic mechanism, the goal to elucidate the effect of polarization on piezoelectric catalytic performance and enhance piezoelectric catalytic performance. Subsequently, the applications of piezoelectric materials in water treatment and environmental pollutant remediation were discussed including degradation of organic pollutants, removal of heavy mental ions, radionuclides, bacteria disinfection and water splitting for H₂ generation. Finally, the development prospects and future outlooks of piezoelectric catalysis were presented in detail.

Reduced Graphene Oxide/Waste-Derived TiO2 Composite Membranes: Preliminary Study of a New Material for Hybrid Wastewater Treatment

This work reports the preliminary results of the development of composite self-assembling membranes obtained by the combination of reduced graphene oxide (rGO) with commercial Degussa P25 titanium dioxide (TiO₂). The purpose is to demonstrate the possibility of combining, in the same self-standing material, the capability to treat wastewater containing both inorganic and organic pollutants by exploiting the established ability of rGO to capture metal ions together with that of TiO₂ to degrade organic substances. Moreover, this study also investigates the potential photocatalytic properties of tionite (TIO), to demonstrate the feasibility of replacing commercial TiO₂ with such waste-derived TiO₂-containing material, fulfilling a circular economy approach. Thus, rGO-TiO₂ and rGO-TIO composite membranes, 1:1 by weight, were prepared and characterized by SEM-EDX, XRD, thermogravimetry, as well as by Raman and UV-Vis spectroscopies to verify the effective and homogeneous integration of the two components. Then, they were tested towards 3-mg L^-1 aqueous synthetic solutions of Fe³⁺ and Cu²⁺ ions to evaluate their metal adsorption ability, with values of the order of 0.1-0.2 mmol g_membrane^-1, comparable or even slightly higher than those of pristine rGO. Finally, the ability of the composites to degrade a common organic pesticide, i.e., Imidacloprid^®, was assessed in preliminary photocatalysis experiments, in which maximum degradation efficiencies of 25% (after 3 h) for rGO-TiO₂ and of 21% (after 1 h) for rGO-TIO were found. The result of tionite-containing membranes is particularly promising and worthy of further investigation, given that the anatase content of tionite is roughly 1/6 of the one in commercial TiO₂.

Toward waterborne protozoa detection using sensing technologies

Drought and limited sufficient water resources will be the main challenges for humankind during the coming years. The lack of water resources for washing, bathing, and drinking increases the use of contaminated water and the risk of waterborne diseases. A considerable number of waterborne outbreaks are due to protozoan parasites that may remain active/alive in harsh environmental conditions. Therefore, a regular monitoring program of water resources using sensitive techniques is needed to decrease the risk of waterborne outbreaks. Wellorganized point-of-care (POC) systems with enough sensitivity and specificity is the holy grail of research for monitoring platforms. In this review, we comprehensively gathered and discussed rapid, selective, and easy-to-use biosensor and nanobiosensor technologies, developed for the early detection of common waterborne protozoa.

Engineering the Performance and Stability of Molybdenum Disulfide for Heavy Metal Removal

Molybdenum disulfide (MoS₂) has recently emerged as one of the most promising water nano-based adsorbent materials for heavy metal removal with the potential to provide an alternative to conventional water decontamination technologies. In this study, we demonstrate the trade-off between mercuric removal capacity and overall MoS₂ adsorbent stability, both driven by MoS₂ synthesis parameters. A bottom-up hydrothermal synthesis setup at various growth temperatures was employed to grow flower-like MoS₂ films onto planar alumina supports. A thorough material characterization suggests that an increase in growth temperature from 150 to 210 °C results in higher MoS₂ crystallinity. Interestingly, elevated growth temperatures resulted in poor mercuric removal (525 mg g^-1, K = 2.2 × 10^-3 h^-1), yet showed enhanced chemical stability (i.e., minimal molybdenum leaching during exposure to mercury). On the other hand, low growth temperatures produce amorphous supported MoS₂, exhibiting superb mercuric removal capabilities (5158 mg g^-1, K = 36.1 × 10^-3 h^-1) but displaying poor stability, resulting in substantial byproduct molybdate leaching. Mercuric removal by crystalline MoS₂ was accomplished by adsorption and electrostatic attraction-based removal mechanisms, whereas redox reactions and HgS crystallization-based removal mechanisms were more dominant when using amorphous MoS₂ for mercury removal. Overall, our study provides essential insights into the delicate balance between MoS₂ mercuric removal capabilities and MoS₂ degradation, both related to material synthesis growth conditions. Employment of nano-enabled water treatments in general, and MoS₂ for heavy metal removal in particular, requires us to better understand these important fundamental trade-off behaviors to achieve sustainable, effective, and responsible implementation of nanotechnologies in large scale systems.

Nanostructured Materials and Advanced Processes for Application in Water Purification

Water pollution is a major environmental problem that has a significant impact on human and animal health and the ecosystem [...].

Emerging application of nanotechnology for mankind

Nanotechnology has proven to be the greatest multidisciplinary field in the current years with potential applications in agriculture, pollution remediation, environmental sustainability, as well as most recently in pharmaceutical industries. As a result of its physical, chemical, and biological productivity, resistance, and matricular organization at a larger scale, the potential of nanocomposites revealed different sorts of assembling structures via testing. Biosensors are known some specifically promising inventions whereas carbon nanotube, magnetic nanoparticles (NPs), quantum dots, and gold NPs showed capability to repair damaged cells, molecular docking, drug-delivery, and nano-remediation of toxic elements. PEGylated(Poly ethyl glycol amyl gated) redox-responsive nanoscale COFs drug delivery from AgNPs and AuNPs are known to be sun blockers in sunscreen lotions. The emerging trends and yet more to be discovered to bridge the gaps forming in the field of nanotechnology, especially insights into environmental concerns and health issues most importantly the food web which is connected with the well beings of mankind to perform its tasks giving necessary results. The current review detailed emerging role of nanomaterials in human life.

Supplementary Information

The online version contains supplementary material available at 10.1007/s42247-023-00461-8.

Green synthesis of silver nanoparticles using Coffea canephora fruit skin extract and its application for mercury detection in face cream samples

Mercury is one of the most toxic heavy metals causing harmful effects on the human body; meanwhile, mercury is found in some face cream products to give a whitening effect. The upper limit concentration of mercury in skin-lightening products defined by the Food and Drug Administration (FDA) is under one mg/L as Hg²⁺. A new green analytical spectrophotometric method for mercury analysis has been developed by employing a biological reagent from fruit skin extract of robusta coffee (Coffea canephora) as a bioreductor for silver ions as well as a stabilizer for the AgNPs product. The detection principle of this method is based on the decrease of the color intensity of silver nanoparticles (AgNPs) after the addition of Hg²⁺ ions due to the re-oxidization of the AgNPs by Hg²⁺ ions to colorless Ag⁺ ions. To achieve the most significant sensitivity, linearity of measurement, and validity, the method was optimized toward the volume of AgNPs and reaction time. In this research, the synthesized AgNPs were also characterized by UV-Vis Spectrometry as well as a particle size analyzer (PSA) to determine the size of nanoparticles. The result showed that the optimum conditions were attained at 4 mL AgNPs solution and 3-min reaction resulting in a linear measurement of Hg²⁺ in the range of 0-15 mg/L with LOD and LOQ of 0.039 and 0.130 mg/L, respectively. This method is quite selective and has been validated by applying it to real face cream samples with satisfactory results supported by average recoveries of close to 100%.

Sustainable Preparation of Graphene Quantum Dots for Metal Ion Sensing Application

Over the past several years, graphene quantum dots (GQDs) have been extensively studied in water treatment and sensing applications because of their exceptional structure-related properties, intrinsic inert carbon property, eco-friendly nature, etc. This work reported on the preparation of GQDs from the ethanolic extracts of eucalyptus tree leaves by a hydrothermal treatment technique. Different heat treatment times and temperatures were used during the hydrothermal treatment technique. The optical, morphological, and compositional analyses of the green-synthesized GQDs were carried out. It can be noted that the product yield of GQDs showed the maximum yield at a reaction temperature of 300 °C. Further, it was noted that at a treatment period of 480 min, the greatest product yield of about 44.34% was attained. The quantum yields of prepared GQDs obtained after 480 min of treatment at 300 °C (named as GQD/300) were noted to be 0.069. Moreover, the D/G ratio of GQD/300 was noted to be 0.532 and this suggested that the GQD/300 developed has a nano-crystalline graphite structure. The TEM images demonstrated the development of GQD/300 with sizes between 2.0 to 5.0 nm. Furthermore, it was noted that the GQD/300 can detect Fe³⁺ in a very selective manner, and hence the developed GQD/300 was successfully used for the metal ion sensing application.

Evaluation of Cytotoxic Effect of Graphene Oxide Added to Mineral Trioxide Aggregate

Aim:

Recently, although studies have shown that biomaterials containing graphene oxide (GO) in biomedicine stand out for their positive effects, the effect of GO on dental tissues when used with dental materials is not well known. The aim of this study was an evaluation of the cytotoxic effects of GO on gingival fibroblasts when it is combined in two different ratios with Mineral Trioxide Aggregate (MTA).

Materials and Methods:

In this in-vitro study, a homogenous mixture of adding +0.1 weight (wt)% and +0.3 wt% GO to Angelus MTA was created (two experimental groups) and compared with pure Angelus MTA and negative control groups. The materials were mixed according to the manufacturer’s instructions, and Teflon molds were used to form 24 disc-shaped samples for each group. The samples were divided into groups according to the simple random sampling method. The cytotoxic effect of samples was determined on gingival fibroblast cells by using the MTT test, and total oxidant status (TOS) and total antioxidant capacity (TAC) kits in 24 and 72 hours. The data were statistically analyzed using one-way ANOVA and Tukey tests.

Results:

A significant difference was found between the material-applied groups and the control group at the TAC 24 and 72 hours and between the groups containing GO and the control group at the MTT 72 hours and TAC and TOS 24 and 72 hours ( p < .05).

Conclusion:

The addition of GO to MTA increased the dose and time-based toxicity and oxidant amount, and decreased antioxidant capacity.

Critical Offset Magnetic PArticle SpectroScopy for rapid and highly sensitive medical point-of-care diagnostics

Magnetic nanoparticles (MNPs) have been adapted for many applications, e.g., bioassays for the detection of biomarkers such as antibodies, by controlled engineering of specific surface properties. Specific measurement of such binding states is of high interest but currently limited to highly sensitive techniques such as ELISA or flow cytometry, which are relatively inflexible, difficult to handle, expensive and time-consuming. Here we report a method named COMPASS (Critical-Offset-Magnetic-Particle-SpectroScopy), which is based on a critical offset magnetic field, enabling sensitive detection to minimal changes in mobility of MNP ensembles, e.g., resulting from SARS-CoV-2 antibodies binding to the S antigen on the surface of functionalized MNPs. With a sensitivity of 0.33 fmole/50 µl (≙7 pM) for SARS-CoV-2-S1 antibodies, measured with a low-cost portable COMPASS device, the proposed technique is competitive with respect to sensitivity while providing flexibility, robustness, and a measurement time of seconds per sample. In addition, initial results with blood serum demonstrate high specificity.

Improved Forward Osmosis Performance of Thin Film Composite Membranes with Graphene Quantum Dots Derived from Eucalyptus Tree Leaves

The major challenges in forward osmosis (FO) are low water flux, high specific reverse solute flux (SRSF), and membrane fouling. The present work addresses these problems by the incorporation of graphene quantum dots (GQDs) in the polyamide (PA) layer of thin-film composite (TFC) membranes, as well as by using an innovative polyethersulfone nanofiber support for the TFC membrane. The GQDs were prepared from eucalyptus leaves using a facile hydrothermal method that requires only deionized water, without the need for any organic solvents or reducing agents. The nanofiber support of the TFC membranes was prepared using solution blow spinning (SBS). The polyamide layer with GQDs was deposited on top of the nanofiber support through interfacial polymerization. This is the first study that reports the fouling resistance of the SBS-nanofiber-supported TFC membranes. The effect of various GQD loadings on the TFC FO membrane performance, its long-term FO testing, cleaning efficiency, and organic fouling resistance were analyzed. It was noted that the FO separation performance of the TFC membranes was improved with the incorporation of 0.05 wt.% GQDs. This study confirmed that the newly developed thin-film nanocomposite membranes demonstrated increased water flux and salt rejection, reduced SRSF, and good antifouling performance in the FO process.

Recent advances in nanomaterial developments for efficient removal of Hg(II) from water

"Water" contamination by mercury Hg(II) has become the biggest concern due to its severe toxicities on public health. There are different conventional techniques like ion exchange, reverse osmosis, and filtration that have been used for the elimination of Hg(II) from the aqueous solutions. Although, these techniques have some drawbacks during the remediation of Hg(II) present in water. Adsorption could be a better option for the elimination of Hg(II) from the aqueous solutions. "Conventional adsorbents" like zeolite, clay, and activated carbons are inefficient for this purpose. Recently, nanomaterials have attracted attention for the elimination of Hg(II) from the aqueous solutions due to high porosity, better surface properties, and high efficiency. In this review, a thorough discussion has been carried out on the synthesis and characterization of nanomaterials along with mechanisms involved in the elimination of Hg(II) from aqueous solutions.

A review on removal strategies of microorganisms from water environment using nanomaterials and their behavioural characteristics

Significant findings for microbial removal have led to expertise on several kinds of nanomaterials that made new paths for removing various biological contaminants in a variety of water resources in recent years. Furthermore, advancements in multifunctional nanocomposites synthesis pave the enhanced possibility for their use in water treatment system design. The adsorption towards microbial elimination has been reviewed and compared in this review article using four common kinds of nanomaterials: carbon materials, metal oxides, metal/metal oxides, polymeric metal oxide nanocomposites and their most important mechanistic behavior also discussed. We also describe and analyze recent findings on the effects of engineered nanomaterials on microbial communities in natural and artificial environments. Understanding the removal mechanistic strategy is crucial to improving the nanoparticles (NPs) efficiency and increasing their applicability against a variety of bacteria in various environmental conditions. Also, our study focused on their behavioral effects on microbial structure and functionality towards the removal. Future research opportunities connected to the use of nanomaterials in microbial control and inactivation with societal and health implications are also discussed. We also highlight a number of interesting research subjects that might be of futuristic interest to the scientific community.

Progress and Prospects of Nanocellulose-Based Membranes for Desalination and Water Treatment

Membrane-based desalination has proved to be the best solution for solving the water shortage issues globally. Membranes are extremely beneficial in the effective recovery of clean water from contaminated water sources, however, the durability as well as the separation efficiency of the membranes are restricted by the type of membrane materials/additives used in the preparation processes. Nanocellulose is one of the most promising green materials for nanocomposite preparation due to its biodegradability, renewability, abundance, easy modification, and exceptional mechanical properties. This nanocellulose has been used in membrane development for desalination application in the recent past. The study discusses the application of membranes based on different nanocellulose forms such as cellulose nanocrystals, cellulose nanofibrils, and bacterial nanocellulose for water desalination applications such as nanofiltration, reverse osmosis, pervaporation, forward osmosis, and membrane distillation. From the analysis of studies, it was confirmed that the nanocellulose-based membranes are effective in the desalination application. The chemical modification of nanocellulose can definitely improve the surface affinity as well as the reactivity of membranes for the efficient separation of specific contaminants/ions.

Nanobioremediation: A sustainable approach for the removal of toxic pollutants from the environment

In recent years, the proportion of organic and inorganic contaminants has increased rapidly due to growing human interference and represents a threat to ecosystems. The removal of these toxic pollutants from the environment is a difficult task. Physical, chemical and biological methods are implemented for the degradation of toxic pollutants from the environment. Among existing technologies, bioremediation in combination with nanotechnology is the most promising and cost-effective method for the removal of pollutants. Numerous studies have shown that exceptional characteristics of nanomaterials such as improved catalysis and adsorption properties as well as high reactivity have been subjects of great interest. There is an emerging trend of employing bacterial, fungal and algal cultures and their components, extracts or biomolecules as catalysts for the sustainable production of nanomaterials. They can serve as facilitators in the bioremediation of toxic compounds by immobilizing or inducing the synthesis of remediating microbial enzymes. Understanding the association between microorganisms, contaminants and nanoparticles (NPs) is of crucial importance. In this review, we focus on the removal of toxic pollutants using the cumulative effects of nanoparticles with microbial technology and their applications in different domains. Besides, we discuss how this novel nanobioremediation technique is significant and contributes towards sustainability.

Engineered Cu-PEN Composites at the Nanoscale: Preparation and Characterisation

As polymeric materials are already used in many industries, the range of their applications is constantly expanding. Therefore, their preparation procedures and the resulting properties require considerable attention. In this work, we designed the surface of polyethylene naphthalate (PEN) introducing copper nanowires. The surface of PEN was transformed into coherent ripple patterns by treatment with a KrF excimer laser. Then, Cu deposition onto nanostructured surfaces by a vacuum evaporation technique was accomplished, giving rise to nanowires. The morphology of the prepared structures was investigated by atomic force microscopy and scanning electron microscopy. Energy dispersive spectroscopy and X-ray photoelectron spectroscopy revealed the distribution of Cu in the nanowires and their gradual oxidation. The optical properties of the Cu nanowires were measured by UV-Vis spectroscopy. The sessile drop method revealed the hydrophobic character of the Cu/PEN surface, which is important for further studies of biological responses. Our study suggests that a combination of laser surface texturing and vacuum evaporation can be an effective and simple method for the preparation of a Cu/polymer nanocomposite with potential exploitation in bioapplications; however, it should be borne in mind that significant post-deposition oxidation of the Cu nanowire occurs, which may open up new strategies for further biological applications.

New fabrication of CuFe2O4/PAMAM nanocomposites by an efficient removal performance for organic dyes: Kinetic study

Today, removing pollutants from water sources is essential because of the population increase and the growing need for safe drinking water. Dyes are one of the most critical pollutants from industrial effluents such as paper and textile industries that profoundly affect the environment. There are several ways to remove environmental contaminants. Magnetic nanoparticles have a high ability to adsorb dyes. Of course, increasing the interaction between magnetic nanomaterials and pollutants is also essential, which can be done using porous materials such as dendrimers. In this work, the synthesis of CuFe₂O₄ magnetite nanoparticles within the polyamidoamine dendrimers structure was used as an efficient sorbent to remove both alizarin reds (ARS) and brilliant green (BG) dyes. Moreover, various parameters for dyes removal were studied. The optimum removal conditions were obtained for ARS within 30 min at a sorbent dose of 2 mg per 5 mL for the initial dye concentration of 7.0 ppm in pH 6 at 25 °C, and for BG within 45 min at a sorbent dose of 5 mg per 5 mL for the initial dye concentration of 17.0 ppm in pH 8 at 25 °C. At the optimum values of the above parameters, both dyes' removal efficiency was more than 97%. Also, the obtained results showed that the adsorption isotherm follows the Langmuir model and Temkin model for ARS and BG, respectively. This method was successfully used for the removal of both dyes in water samples.

V2O5, CeO2 and Their MWCNTs Nanocomposites Modified for the Removal of Kerosene from Water

In this paper, the application of multiwalled carbon nanotubes (MWCNTs) based on metal oxide nanocomposites as adsorbents for the removal of hydrocarbons such as kerosene from water was investigated. Functionalized MWCNTs were obtained by chemical oxidation using concentrated sulfuric and nitric acids. V₂O₅, CeO_2, and V₂O₅:CeO₂ nanocomposites were prepared using the hydrothermal method followed by deposition of these oxides over MWCNTs. Individual and mixed metal oxides, fresh MWCNTs, and metal oxide nanoparticle-doped MWCNTs using different analysis techniques were characterized. XRD, TEM, SEM, EDX, AFM, Raman, TG/DTA, and BET techniques were used to determine the structure as well as chemical and morphological properties of the newly prepared adsorbents. Fresh MWCNTs, Ce/MWCNTs, V/MWCNTs, and V:Ce/MWCNTs were applied for the removal of kerosene from a model solution of water. GC analysis indicated that high kerosene removal efficiency (85%) and adsorption capacity (4270 mg/g) after 60 min of treatment were obtained over V:Ce/MWCNTs in comparison with fresh MWCNTs, Ce/MWCNTs and V/MWCNTs. The kinetic data were analyzed using the pseudo-first order, pseudo-second order, and intra-particle diffusion rate equations.

Converting Complex Sewage Containing Oil, Silt, and Bacteria into Clean Water by a 3D Printed Multiscale and Multifunctional Filter

The exacerbating water pollution and water resource shortage pose a great danger to human health and make it imperative to recycle and treat the sewage. In this study, a direct-writing three-dimensional (3D) printing technology was adopted to prepare a 3D sodium alginate (SA)/graphene oxide (GO)/Ag nanoparticle (AgNP) aerogel (SGA), aiming to turn the complex sewage containing oil, silt, and bacteria into clean water depending only on gravity separation. The physicochemical properties and surface structure of the synthesized SGA were characterized by X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The swelling rate, mechanical properties, antibacterial properties, oil and water separation effect, and durable stability of the filter membrane were also investigated to verify the versatility of the SGA filter. The results showed that GO helped improve the mechanical properties of the printed filter to withstand water impact during the filtration process. The printed filter had a well-designed and multiscale gradient pore structure, which can effectively intercept particles with different sizes to separate the silt from water, and the turbidity of the filtered water can be reduced from 60 to 1 nephelometric turbidity unit (NTU). The presence of SA endowed the printed filter with hydrophilic and oleophobic behaviors, which can effectively separate various kinds of oils from water. The uniform distribution of AgNPs in the filter produced via a facile and green reduction of SA facilitated the efficient bactericidal ability of the printed filter during the filtration process; meanwhile, the lower release concentration of Ag ions ensured drinking safety. What is more, the filter can be easily produced on a large scale and used for different sewage treatment situations with a durable stability of over 30 days. Taken together, the printed SGA filter has a broad application prospect in complex sewage treatment, providing a special solution for sewage treatment in poverty areas.

Recent Advancements in the Nanomaterial Application in Concrete and Its Ecological Impact

At present, nanotechnology is a significant research area in different countries, owing to its immense ability along with its economic impact. Nanotechnology is the scientific study, development, manufacturing, and processing of structures and materials on a nanoscale level. It has tremendous application in different industries such as construction. This study discusses the various progressive uses of nanomaterials in concrete, as well as their related health risks and environmental impacts. Nanomaterials such as nanosilica, nano-TiO₂, carbon nanotubes (CNTs), ferric oxides, polycarboxylates, and nanocellulose have the capability to increase the durability of buildings by improving their mechanical and thermal properties. This could cause an indirect reduction in energy usage and total expenses in the concrete industry. However, due to the uncertainties and irregularities in size, shape, and chemical compositions, some nanosized materials might have harmful effects on the environment and human health. Acknowledgement of the possible beneficial impacts and inadvertent dangers of these nanosized materials to the environment will be extremely important when pursuing progress in the upcoming years. This research paper is expected to bring proper attention to the probable effects of construction waste, together with the importance of proper regulations, on the final disposal of the construction waste.

Heavy Metals Removal from Aqueous Solutions by Multiwall Carbon Nanotubes: Effect of MWCNTs Dispersion

Carbon nanotubes (CNTs) are one of the most studied nanoparticles due to their physical, chemical and electronic properties. However, strong Van der Waals bonds, which promote CNTs aggregation are usually present, affecting their unique properties. Avoiding CNTs aggregation is one of the main difficulties when using these nanoparticles. Regarding the adsorption capacity of CNTs, the tendency of CNTs to aggregate decreases the surface area available to retain contaminants. One way to overcome this issue is by changing the surface energy of CNTs through chemical (covalent and noncovalent methods) or mechanical stabilization, but there is not yet a unique solution to solve this problem. In this work, a chemical noncovalent method (addition of surfactants) combined with mechanical energy (ultrasounds) was applied for CNTs stabilization, and the influence in heavy metal ions removal, Pb (II), Cu (II), Ni (II) and Zn (II), an area of high environmental relevance, was evaluated. It was proved that high amounts of metals could be removed from water during the first eighteen hours. Competitive adsorption between heavy metals, during adsorption tests with the simultaneous presence of all ions, was also studied and it was possible to prove that the electronegativity and atomic radius of cations influence their removal. Pb (II) and Cu (II) were the metals removed in higher percentages, and Ni (II) and Zn (II) were the metals less removed during competitive adsorption. Finally, the results obtained show that MWCNTs, if adequately dispersed, present a good solution for the treatment of water contaminated with highly toxic heavy metals, even when using very low concentrations of Multiwall Carbon Nanotubes (MWCNTs).

Impact of metal nanoparticles on the structure and function of metabolic enzymes

The widespread use of nanoparticles raises many serious concerns about the safety and environmental impact of nanoparticles. Therefore, risk assessments of specific nanoparticles in occupational and environmental exposure are essential before their large-scale production and applications, especially in medicine and for usage in household items. In this study, the effects of five different metal nanoparticles on the structure, stability, and function of four metabolic enzymes were evaluated using various biophysical techniques. Our results show that Cu nanoparticles exhibited the most significant adverse effects on the structures, stability, and activities of all the metabolic enzymes. Zn nanoparticles caused moderate adverse effects on these enzymes. The rest of the metal (Al, Fe, and Ni) nanoparticles had a relatively lower impact on the metabolic enzymes. Our data indicated that Cu nanoparticles promote metal-catalyzed disulfide bond formation in these proteins. In summary, some metal nanoparticles can cause adverse effects on the structure, function, and stability of metabolic enzymes. In addition, metal nanoparticles may affect protein homeostasis in the cytosol or extracellular fluids.

Scalable synthesis of monodisperse and recyclable sulphonated polystyrene microspheres for sustainable elimination of heavy metals in wastewater

Herein, we demonstrate a scalable method for fabricating monodisperse sulphonated polystyrene (SPS) microspheres with abundant sulphonic acid groups and excellent heavy metal removal ability. A comprehensive characterization through SEM, EDS, FT-IR, TG, XRD and XPS confirmed the formation of the SPS microspheres. Take advantage of the abundant sulphonic acid groups on the surface of microspheres, as well as the superior monodisperse properties, adsorption ability of SPS microspheres both in quantity and speed have been enhanced. The adsorption equilibrium obeyed the Langmuir isotherm model with the theoretical maximum capacities of 49.16, 15.38 and 13.89 mg·g-1 for Pb2+, Zn2+ and Cu2+, respectively (30°C, pH = 3.5). Besides, the adsorption equilibriums of Pb2+ onto SPS microspheres can be achieved within only 1 min and the adsorption kinetics can be fitted by a pseudo-second-order kinetics model. More importantly, because of the micron structure of the SPS microspheres, it could overcome the excessive hydrophilia brought by rich sulphonic acid groups and thereby easily separated, which maintain a good recyclable capacity after five regeneration cycles. With the excellent adsorption ability and reusability, SPS microspheres can efficiently handle the polluted water in a convenience and rapid process, which satisfies the sustainable pollution treatment in heavy metals elimination.

Reduced Graphene Oxide Membranes as Potential Self-Assembling Filter for Wastewater Treatment

This work focuses on the investigation of the capability of reduced graphene oxide (rGO) filters to remove metals from various wastewater. The process to produce rGO membranes is reported and discussed, as well as their ability to capture ions in complex solutions, such as tap or industrial wastewater. Multi-ion solutions, containing Cu2+, Fe3+, Ni2+, and Mn2+ to simulate mine wastewater, or Ca2+ and Mg2+ to mimic drinkable water, were used as models. In mono-ionic solutions, the best capture efficiency values were proved for Ca2+, Fe3+, and Ni2+ ions, while a matrix effect was found for multi-ion solutions. However, interesting capture efficiencies were measured in the range of 30–90%, depending on the specific ion, for both single and multi-ion solutions. An attempt is proposed to correlate ions capture efficiency with ions characteristics, such as ionic radius or charge. Combining a satisfactory capture efficiency with low costs and ease of treatment unit operations, the approach here proposed is considered promising to replace other more complex and expensive filtration techniques.