1
|
Nazarychev VM, Lyulin SV. The Effect of Mechanical Elongation on the Thermal Conductivity of Amorphous and Semicrystalline Thermoplastic Polyimides: Atomistic Simulations. Polymers (Basel) 2023; 15:2926. [PMID: 37447571 DOI: 10.3390/polym15132926] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 05/31/2023] [Revised: 06/28/2023] [Accepted: 06/29/2023] [Indexed: 07/15/2023] Open
Abstract
Over the past few decades, the enhancement of polymer thermal conductivity has attracted considerable attention in the scientific community due to its potential for the development of new thermal interface materials (TIM) for both electronic and electrical devices. The mechanical elongation of polymers may be considered as an appropriate tool for the improvement of heat transport through polymers without the necessary addition of nanofillers. Polyimides (PIs) in particular have some of the best thermal, dielectric, and mechanical properties, as well as radiation and chemical resistance. They can therefore be used as polymer binders in TIM without compromising their dielectric properties. In the present study, the effects of uniaxial deformation on the thermal conductivity of thermoplastic PIs were examined for the first time using atomistic computer simulations. We believe that this approach will be important for the development of thermal interface materials based on thermoplastic PIs with improved thermal conductivity properties. Current research has focused on the analysis of three thermoplastic PIs: two semicrystalline, namely BPDA-P3 and R-BAPB; and one amorphous, ULTEMTM. To evaluate the impact of uniaxial deformation on the thermal conductivity, samples of these PIs were deformed up to 200% at a temperature of 600 K, slightly above the melting temperatures of BPDA-P3 and R-BAPB. The thermal conductivity coefficients of these PIs increased in the glassy state and above the glass transition point. Notably, some improvement in the thermal conductivity of the amorphous polyimide ULTEMTM was achieved. Our study demonstrates that the thermal conductivity coefficient is anisotropic in different directions with respect to the deformation axis and shows a significant increase in both semicrystalline and amorphous PIs in the direction parallel to the deformation. Both types of structural ordering (self-ordering of semicrystalline PI and mechanical elongation) led to the same significant increase in thermal conductivity coefficient.
Collapse
Affiliation(s)
- Victor M Nazarychev
- Institute of Macromolecular Compounds, Russian Academy of Sciences, Bolshoi Prospect V.O. 31, 199004 St. Petersburg, Russia
| | - Sergey V Lyulin
- Institute of Macromolecular Compounds, Russian Academy of Sciences, Bolshoi Prospect V.O. 31, 199004 St. Petersburg, Russia
| |
Collapse
|
2
|
Zhao R, Wu H, Dong X, Xu M, Wang Z, Wang X. Enhancing the Toughness of Free-Standing Polyimide Films for Advanced Electronics Applications: A Study on the Impact of Film-Forming Processes. Polymers (Basel) 2023; 15:polym15092073. [PMID: 37177218 PMCID: PMC10180538 DOI: 10.3390/polym15092073] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/06/2023] [Revised: 04/23/2023] [Accepted: 04/25/2023] [Indexed: 05/15/2023] Open
Abstract
High-quality and free-standing polyimide (PI) film with desirable mechanical properties and uniformity is in high demand due to its widespread applications in highly precise flexible and chip-integrated sensors. In this study, a free-standing PI film with high toughness was successfully prepared using a diamine monomer with ether linkages. The prepared PI films exhibited significantly superior mechanical properties compared to PI films of the same molecular structure, which can be attributed to the systematic exploration of the film-forming process. The exploration of the film-forming process includes the curing procedures, film-forming substrates, and annealing treatments. Additionally, the thickness uniformity and surface homogeneity of free-standing films were crucial for toughness. Increasing the crystallinity of the PI films by eliminating residual stress also contributed to their high strength. The results demonstrate that by adjusting the above-mentioned factors, the prepared PI films possess excellent mechanical properties, with tensile strength and elongation at break of 194.71 MPa and 130.13%, respectively.
Collapse
Affiliation(s)
- Ruoqing Zhao
- Frontiers Science Center for Flexible Electronics (FSCFE), Shaanxi Institute of Flexible Electronics (SIFE), Northwestern Polytechnical University, Xi'an 710072, China
| | - Hao Wu
- Frontiers Science Center for Flexible Electronics (FSCFE), Shaanxi Institute of Flexible Electronics (SIFE), Northwestern Polytechnical University, Xi'an 710072, China
| | - Xuan Dong
- Frontiers Science Center for Flexible Electronics (FSCFE), Shaanxi Institute of Flexible Electronics (SIFE), Northwestern Polytechnical University, Xi'an 710072, China
| | - Manzhang Xu
- Frontiers Science Center for Flexible Electronics (FSCFE), Shaanxi Institute of Flexible Electronics (SIFE), Northwestern Polytechnical University, Xi'an 710072, China
| | - Zhenhua Wang
- Frontiers Science Center for Flexible Electronics (FSCFE), Shaanxi Institute of Flexible Electronics (SIFE), Northwestern Polytechnical University, Xi'an 710072, China
| | - Xuewen Wang
- Frontiers Science Center for Flexible Electronics (FSCFE), Shaanxi Institute of Flexible Electronics (SIFE), Northwestern Polytechnical University, Xi'an 710072, China
| |
Collapse
|
3
|
Reda H, Chazirakis A, Power AJ, Harmandaris V. Mechanical Behavior of Polymer Nanocomposites via Atomistic Simulations: Conformational Heterogeneity and the Role of Strain Rate. J Phys Chem B 2022; 126:7429-7444. [DOI: 10.1021/acs.jpcb.2c04597] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/28/2022]
Affiliation(s)
- Hilal Reda
- Computation-based Science and Technology Research Center, The Cyprus Institute, Aglantzia, 2121, Nicosia, Cyprus
| | - Anthony Chazirakis
- Institute of Applied and Computational Mathematics, Foundation for Research and Technology - Hellas, Heraklion GR-71110, Greece
| | - Albert J. Power
- Institute of Applied and Computational Mathematics, Foundation for Research and Technology - Hellas, Heraklion GR-71110, Greece
- Department of Mathematics and Applied Mathematics, University of Crete, Heraklion GR-71110, Greece
| | - Vagelis Harmandaris
- Institute of Applied and Computational Mathematics, Foundation for Research and Technology - Hellas, Heraklion GR-71110, Greece
- Department of Mathematics and Applied Mathematics, University of Crete, Heraklion GR-71110, Greece
- Computation-based Science and Technology Research Center, The Cyprus Institute, Nicosia 2121, Cyprus
| |
Collapse
|
4
|
Dobrovskiy AY, Nazarychev VM, Volgin IV, Lyulin SV. The Transport Properties of Semi-Crystalline Polyetherimide BPDA-P3 in Amorphous and Ordered States: Computer Simulations. MEMBRANES 2022; 12:856. [PMID: 36135875 PMCID: PMC9504751 DOI: 10.3390/membranes12090856] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Figures] [Subscribe] [Scholar Register] [Received: 07/31/2022] [Revised: 08/29/2022] [Accepted: 08/30/2022] [Indexed: 06/16/2023]
Abstract
The effect of polymer chain ordering on the transport properties of the polymer membrane was examined for the semi-crystalline heterocyclic polyetherimide (PEI) BPDA-P3 based on 3,3',4,4'-biphenyltetracarboxylic dianhydride (BPDA) and diamine 1,4-bis [4-(4-aminophenoxy)phenoxy]benzene (P3). All-atom Molecular Dynamics (MD) simulations were used to investigate the gas diffusion process carried through the pores of a free volume several nanometers in size. The long-term (~30 μs) MD simulations of BPDA-P3 were performed at T = 600 K, close to the experimental value of the melting temperature (Tm ≈ 577 K). It was found during the simulations that the transition of the PEI from an amorphous state to an ordered one occurred. We determined a decrease in solubility for both the gases examined (CO2 and CH4), caused by the redistribution of free volume elements occurring during the structural ordering of the polymer chains in glassy state (Tg ≈ 487 K). By analyzing the diffusion coefficients in the ordered state, the presence of gas diffusion anisotropy was found. However, the averaged values of the diffusion coefficients did not differ from each other in the amorphous and ordered states. Thus, permeability in the observed system is primarily determined by gas solubility, rather than by gas diffusion.
Collapse
Affiliation(s)
| | | | | | - Sergey V. Lyulin
- Institute of Macromolecular Compounds, Russian Academy of Sciences, Bolshoj pr. 31 (V.O.), 199004 St. Petersburg, Russia; (A.Y.D.); (V.M.N.); (I.V.V.)
| |
Collapse
|
5
|
Nazarychev VM, Vaganov GV, Larin SV, Didenko AL, Elokhovskiy VY, Svetlichnyi VM, Yudin VE, Lyulin SV. Rheological and Mechanical Properties of Thermoplastic Crystallizable Polyimide-Based Nanocomposites Filled with Carbon Nanotubes: Computer Simulations and Experiments. Polymers (Basel) 2022; 14:polym14153154. [PMID: 35956666 PMCID: PMC9370852 DOI: 10.3390/polym14153154] [Citation(s) in RCA: 3] [Impact Index Per Article: 1.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/30/2022] [Revised: 07/23/2022] [Accepted: 07/28/2022] [Indexed: 11/24/2022] Open
Abstract
Recently, a strong structural ordering of thermoplastic semi-crystalline polyimides near single-walled carbon nanotubes (SWCNTs) was found that can enhance their mechanical properties. In this study, a comparative analysis of the results of microsecond-scale all-atom computer simulations and experimental measurements of thermoplastic semi-crystalline polyimide R-BAPB synthesized on the basis of dianhydride R (1,3-bis-(3′,4-dicarboxyphenoxy) benzene) and diamine BAPB (4,4′-bis-(4″-aminophenoxy) biphenyl) near the SWCNTs on the rheological properties of nanocomposites was performed. We observe the viscosity increase in the SWCNT-filled R-BAPB in the melt state both in computer simulations and experiments. For the first time, it is proven by computer simulation that this viscosity change is related to the structural ordering of the R-BAPB in the vicinity of SWCNT but not to the formation of interchain linkage. Additionally, strong anisotropy of the rheological properties of the R-BAPB near the SWCNT surface was detected due to the polyimide chain orientation. The increase in the viscosity of the polymer in the viscous-flow state and an increase in the values of the mechanical characteristics (Young’s modulus and yield peak) of the SWCNT-R-BAPB nanocomposites in the glassy state are stronger in the directions along the ordering of polymer chains close to the carbon nanofiller surface. Thus, the new experimental data obtained on the R-BAPB-based nanocomposites filled with SWCNT, being extensively compared with simulation results, confirm the idea of the influence of macromolecular ordering near the carbon nanotube on the mechanical characteristics of the composite material.
Collapse
|
6
|
Ivan’kova E, Vaganov G, Didenko A, Popova E, Elokhovskiy V, Bugrov A, Svetlichnyi V, Kasatkin I, Yudin V. Investigation of Polyetherimide Melt-Extruded Fibers Modified by Carbon Nanoparticles. MATERIALS 2021; 14:ma14237251. [PMID: 34885406 PMCID: PMC8658288 DOI: 10.3390/ma14237251] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.7] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 11/01/2021] [Revised: 11/20/2021] [Accepted: 11/25/2021] [Indexed: 11/16/2022]
Abstract
The fibers based on thermoplastic partially crystalline polyetherimide R-BAPB modified by vapor grown carbon nanofibers (VGCF) were prepared by melt extrusion, exposed to orientational drawing, and crystallized. All of the samples were examined by scanning electron microscopy, X-ray scattering, and differential scanning calorimetry to study how the carbon nanofiller influences on the internal structure and crystallization behavior of the obtained R-BAPB fibers. The mechanical properties of the composite R-BAPB fibers were also determined. It was found that VGCF nanoparticles introduced into R-BAPB polyimide can act as a nucleating agent that leads, in turn, to significant changes in the composite fibers morphology as well as thermal and mechanical characteristics. VGCF are able to improve an orientation degree of the R-BAPB macromolecules along the fiber direction, accelerate crystallization rate of the polymer, and enhance the fiber stability during crystallization process.
Collapse
Affiliation(s)
- Elena Ivan’kova
- Institute of Macromolecular Compounds of Russian Academy of Sciences, V.O., Bol’shoy pr. 31, St. Petersburg 199004, Russia; (G.V.); (A.D.); (E.P.); (V.E.); (A.B.); (V.S.); (V.Y.)
- Correspondence:
| | - Gleb Vaganov
- Institute of Macromolecular Compounds of Russian Academy of Sciences, V.O., Bol’shoy pr. 31, St. Petersburg 199004, Russia; (G.V.); (A.D.); (E.P.); (V.E.); (A.B.); (V.S.); (V.Y.)
| | - Andrey Didenko
- Institute of Macromolecular Compounds of Russian Academy of Sciences, V.O., Bol’shoy pr. 31, St. Petersburg 199004, Russia; (G.V.); (A.D.); (E.P.); (V.E.); (A.B.); (V.S.); (V.Y.)
| | - Elena Popova
- Institute of Macromolecular Compounds of Russian Academy of Sciences, V.O., Bol’shoy pr. 31, St. Petersburg 199004, Russia; (G.V.); (A.D.); (E.P.); (V.E.); (A.B.); (V.S.); (V.Y.)
| | - Vladimir Elokhovskiy
- Institute of Macromolecular Compounds of Russian Academy of Sciences, V.O., Bol’shoy pr. 31, St. Petersburg 199004, Russia; (G.V.); (A.D.); (E.P.); (V.E.); (A.B.); (V.S.); (V.Y.)
| | - Alexander Bugrov
- Institute of Macromolecular Compounds of Russian Academy of Sciences, V.O., Bol’shoy pr. 31, St. Petersburg 199004, Russia; (G.V.); (A.D.); (E.P.); (V.E.); (A.B.); (V.S.); (V.Y.)
- Department of Physical Chemistry, Saint Petersburg Electrotechnical University (ETU “LETI”), ul. Professora Popova 5, St. Petersburg 197376, Russia
| | - Valentin Svetlichnyi
- Institute of Macromolecular Compounds of Russian Academy of Sciences, V.O., Bol’shoy pr. 31, St. Petersburg 199004, Russia; (G.V.); (A.D.); (E.P.); (V.E.); (A.B.); (V.S.); (V.Y.)
| | - Igor Kasatkin
- Research Centre for X-ray Diffraction Studies, Saint Petersburg State University, Universitetskaya nab. 7/9, St. Petersburg 199034, Russia;
| | - Vladimir Yudin
- Institute of Macromolecular Compounds of Russian Academy of Sciences, V.O., Bol’shoy pr. 31, St. Petersburg 199004, Russia; (G.V.); (A.D.); (E.P.); (V.E.); (A.B.); (V.S.); (V.Y.)
| |
Collapse
|
7
|
Ogbonna VE, Popoola API, Popoola OM, Adeosun SO. Recent progress on improving the mechanical, thermal and electrical conductivity properties of polyimide matrix composites from nanofillers perspective for technological applications. JOURNAL OF POLYMER ENGINEERING 2021. [DOI: 10.1515/polyeng-2021-0176] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.7] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 11/15/2022]
Abstract
Abstract
The adoption of polymer nanocomposites in the design/manufacturing of parts for engineering and technological applications showcases their outstanding properties. Among the polymer nanocomposites, polyimide (PI) nanocomposites have attracted much attention as a composite material capable of withstanding mechanical, thermal and electrical stresses, hence engineered for use in harsh environments. However, the nanocomposites are limited to the application area that demands conduction polymer and polymer composites due to the low electrical conductivity of PI. Although, there has been advancement in improving the mechanical, thermal and electrical properties of PI nanocomposites. Thus, the review focuses on recent progress on improving the mechanical, thermal and electrical conductivity properties of PI nanocomposites via the incorporation of carbon nanotubes (CNTs), graphene and graphene oxide (GO) fillers into the PI matrix. The review summarises the influence of CNTs, graphene and GO on the mechanical and conductivity properties of PI nanocomposites. The authors ended the review with advancement, challenges and recommendations for future improvement of PI reinforced conductive nanofillers composites. Therefore, the review study proffers an understanding of the improvement and selection of PI nanocomposites material for mechanical, thermal and electrical conductivity applications. Additionally, in the area of conductive polymer nanocomposites, this review will also pave way for future study.
Collapse
Affiliation(s)
- Victor Ekene Ogbonna
- Chemical, Metallurgical & Materials Engineering , Tshwane University of Technology , P.M.B X680 , Pretoria , South Africa
| | - A. Patricia I. Popoola
- Chemical, Metallurgical & Materials Engineering , Tshwane University of Technology , P.M.B X680 , Pretoria , South Africa
| | - Olawale M. Popoola
- Centre for Energy and Power , Tshwane University of Technology , P.M.B X680 , Pretoria , South Africa
| | - Samson O. Adeosun
- Metallurgical & Materials Engineering , University of Lagos , Yaba , Lagos 23401 , Nigeria
| |
Collapse
|
8
|
Facile Preparation of Highly Conductive Poly(amide-imide) Composite Films beyond 1000 S m -1 through Ternary Blend Strategy. Polymers (Basel) 2019; 11:polym11030546. [PMID: 30960530 PMCID: PMC6473783 DOI: 10.3390/polym11030546] [Citation(s) in RCA: 19] [Impact Index Per Article: 3.8] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 01/12/2019] [Revised: 03/12/2019] [Accepted: 03/18/2019] [Indexed: 12/02/2022] Open
Abstract
Highly conductive thin films with suitable mechanical performances play a significant role in modern electronic industry. Herein, a series of ternary conductive polymer composites were fabricated by incorporating carbon black (CB) into binary conductive polymer composites of poly(amide-imide) (PAI) and polyaniline (PANI) to enhance their mechanical and conductive properties simultaneously. By varying the composition of PAI/PANI/CB ternary films, the conductivity enhanced by two orders of magnitude compared with the sum of PAI/PANI and PAI/CB binary conductive polymer composites, and a high conductivity of 1160 S m−1 was achieved. The improved conductivity is mainly because much more continuous conductive networks were constructed in the ternary conductive polymer composites. With the help of the unusual morphology, the tensile strength was also enhanced by more than 80% from 21 to 38 MPa. The origin for the improved morphology was discussed for further improvement.
Collapse
|
9
|
Glova AD, Volgin IV, Nazarychev VM, Larin SV, Lyulin SV, Gurtovenko AA. Toward realistic computer modeling of paraffin-based composite materials: critical assessment of atomic-scale models of paraffins. RSC Adv 2019; 9:38834-38847. [PMID: 35540183 PMCID: PMC9076000 DOI: 10.1039/c9ra07325f] [Citation(s) in RCA: 22] [Impact Index Per Article: 4.4] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 09/11/2019] [Revised: 08/24/2020] [Accepted: 11/19/2019] [Indexed: 11/30/2022] Open
Abstract
Paraffin-based composites represent a promising class of materials with numerous practical applications such as e.g. heat storage. Computer modeling of these complex multicomponent systems requires a proper theoretical description of both the n-alkane matrix and the non-alkane filler molecules. The latter can be modeled with the use of a state-of-the-art general-purpose force field such as GAFF, CHARMM, OPLS-AA and GROMOS, while the paraffin matrix is traditionally described in the frame of relatively old, alkane-specific force fields (TraPPE, NERD, and PYS). In this paper we link these two types of models and evaluate the performance of several general-purpose force fields in computer modeling of paraffin by their systematic comparison with earlier alkane-specific models as well as with experimental data. To this end, we have performed molecular dynamics simulations of n-eicosane bulk samples with the use of 10 different force fields: TraPPE, NERD, PYS, OPLS-UA, GROMOS, GAFF, GAFF2, OPLS-AA, L-OPLS-AA, and CHARMM36. For each force field we calculated several thermal, structural and dynamic characteristics of n-eicosane over a wide temperature range. Overall, our findings show that the general-purpose force fields such as CHARMM36, L-OPLS-AA and GAFF/GAFF2 are able to provide a realistic description of n-eicosane samples. While alkane-specific models outperform most general-purpose force fields as far as the temperature dependence of mass density, the coefficient of volumetric thermal expansion in the liquid state, and the crystallization temperature are concerned, L-OPLS-AA, CHARMM36 and GAFF2 force fields provide a better match with experiment for the shear viscosity and the diffusion coefficient in melt. Furthermore, we show that most general-purpose force fields are able to reproduce qualitatively the experimental triclinic crystal structure of n-eicosane at low temperatures. Atomic-scale computational models of paraffins are critically assessed and compared.![]()
Collapse
Affiliation(s)
- Artyom D. Glova
- Institute of Macromolecular Compounds
- Russian Academy of Sciences
- St. Petersburg
- Russia
| | - Igor V. Volgin
- Institute of Macromolecular Compounds
- Russian Academy of Sciences
- St. Petersburg
- Russia
| | - Victor M. Nazarychev
- Institute of Macromolecular Compounds
- Russian Academy of Sciences
- St. Petersburg
- Russia
| | - Sergey V. Larin
- Institute of Macromolecular Compounds
- Russian Academy of Sciences
- St. Petersburg
- Russia
| | - Sergey V. Lyulin
- Institute of Macromolecular Compounds
- Russian Academy of Sciences
- St. Petersburg
- Russia
- Faculty of Physics
| | - Andrey A. Gurtovenko
- Institute of Macromolecular Compounds
- Russian Academy of Sciences
- St. Petersburg
- Russia
- Faculty of Physics
| |
Collapse
|