Binary Green Blends of Poly(lactic acid) with Poly(butylene adipate-co-butylene terephthalate) and Poly(butylene succinate-co-butylene adipate) and Their Nanocomposites

Natural lignocellulosic biomass structure inspired CNF/Lignin/PBAT composite film with thermoplastic, antibacterial and UV-blocking abilities

The development of a thermoplastic, biodegradable composite material to replace conventional polymers derived from petroleum was the main area of concentration. Herein, a method for preparing antibacterial, UV-blocking and degradable CNF/Lignin/PBAT composite films (CLP) using cellulose nanofibrils (CNF), lignin, and Poly (butylene adipate-terephthalate) (PBAT) as raw materials by solution casting method was described. With the adding of PBAT, the thermal stability, thermoplastic, mechanical properties were enhanced by improving the compatibility between components. The maximum tensile strength of CLP could reach 189.72 MPa, which increased 25.5 % compared to CNF/Lignin film. The average initial decomposition temperature could reach 321 °C, which was much higher than that of CNF and lignin. At the same time, its good heat-sealing performance made it suitable for practical use. Meanwhile, the composite films had excellent UV resistance and could block over 95 % of UV light. The antibacterial results indicated that the films had a good inhibitory effect on E. coli and S. aureus, with a maximum inhibitory ring diameter of 5.56 and 6.36 mm. In addition, the composite film also had excellent barrier capability to liquid and gas. The prepared film had potential to produce flexible packing, industrial compositing and biomedical fields.

Fractionated lignin as a green compatibilizer to improve the compatibility of poly (butylene adipate-co-terephthalate) /polylactic acid composites

Blending poly (butylene adipate-co-terephthalate) (PBAT) and polylactic acid (PLA) is a cost-effective strategy to obtain biodegradable plastic with complementary properties. However, the incompatibility between PBAT and PLA is a great challenge for fabricating high-performance composite films. Herein, the ethyl acetate fractionated lignin with the small glass transition temperature and low molecular weight was achieved and incorporated into the PBAT/PLA composite as a compatibilizer. The fractionated lignin can be uniformly dispersed within the PBAT/PLA matrix through a melt blending process and interact with the molecular chain of PBAT and PLA as a bonding bridge, which enhances the intermolecular interactions and reduces the interfacial tension of PBAT/PLA. By adding fractionated lignin, the tensile strength of the PBAT/PLA composite increased by 35.4 % and the yield strength increased by 37.7 %. Owing to lignin, the composite films possessed the ultraviolet shielding function and exhibited better water vapor barrier properties (1.73 ± 0.08 × 10-13 g·cm/cm2·s·Pa). This work conclusively demonstrated that fractionated lignin can be used as a green compatibilizer and a low-cost functional filler for PBAT/PLA materials, and provides guidance for the application of lignin in biodegradable plastics.

Improving the compatibility and toughness of sustainable polylactide/poly(butylene adipate-co-terephthalate) blends by incorporation of peroxide and diacrylate

Polylactide/poly(butylene adipate-co-terephthalate) (PLA/PBAT) blends were compatibilized using dicumyl peroxide (DCP) and poly(ethylene glycol) 600 diacrylate (PEG600DA) through a one-step melt-blending process. The compatibility and performance of these blends were subsequently characterized. The results showed that grafts formed "in situ" effectively improved the compatibility and interfacial adhesion between PLA and PBAT phases. Melt viscosity and elasticity of both the PLA/PBAT/DCP and PLA/PBAT/DCP/PEG600DA blends evinced significant increases. Compared to PLA alone, both cold and melt crystallization abilities of the PLA/PBAT/DCP/PEG600DA blends were enhanced, with crystallinities increasing by 5 % - 10 %. Furthermore, the thermal stability, as well as hydrophobicity and oleophobicity of the compatibilized blends improved. In comparison with PLA, the elongation at break and notched impact strength for the PLA/PBAT/DCP/PEG600DA (60/40/0.1/4) blend achieved increases of 290 % and 44.23 kJ/m2, corresponding to improvements of 279 % and 1457 %, respectively. The toughening effect was substantially influenced by the ductile matrix (either a co-continuous phase or a flexible PBAT matrix) in addition to the strong interfacial adhesion and fine phase domain. These eco-friendly blends exhibit considerable potential for packaging articles and 3D printing products owing to their excellent mechanical properties and enhanced melt rheology.

A Green Treatment Mitigates the Limitations of Coffee Silver Skin as a Filler for PLA/PBSA Compatibilized Biocomposites

The development of fully renewable and biodegradable composites for short-term applications was pursued by combining a compatibilized poly(lactic acid) (PLA)/poly(butylene succinate-co-adipate) (PBSA) (60:40 wt:wt) blend with coffee silver skin (CSS), an industrial byproduct from coffee processing. An epoxy-based reactive agent (Joncryl ADR-4468) was added as a compatibilizer. CSS was incorporated at 5, 10, and 20 wt% in the blend both in the as-received state and after a simple thermal treatment in boiling water, which was performed to mitigate the negative impact of this filler on the rheological and mechanical properties of the blend. The CSS treatment effectively increased the filler degradation temperature of 30-40 °C, enabling stable melt processing of the composites. It also improved filler-matrix adhesion, resulting in enhanced impact properties (up to +172% increase in impact energy compared to the untreated filler). Therefore, treated CSS demonstrated potential as an effective green reinforcement for PLA/PBSA blends for rigid packaging applications. Future works will focus on studying suitable surface modification of CSS to further increase the interfacial interaction and the tensile quasi-static properties, to fully exploit the capabilities of this renewable material toward the development of eco-friendly composites.

New Functional Bionanocomposites by Combining Hybrid Host-Guest Systems with a Fully Biobased Poly(lactic acid)/Poly(butylene succinate-co-adipate) (PLA/PBSA) Binary Blend

In this study, we have developed innovative polymer nanocomposites by integrating magnesium-aluminum layered double hydroxide (LDH)-based nanocarriers modified with functional molecules into a fully biobased poly(lactic acid)/poly(butylene succinate-co-adipate) (PLA/PBSA) matrix. These LDH-based hybrid host-guest systems contain bioactive compounds like rosmarinic acid, ferulic acid, and glycyrrhetinic acid, known for their antioxidant, antimicrobial, and anti-inflammatory properties. The bioactive molecules can be gradually released from the nanocarriers over time, allowing for sustained and controlled delivery in various applications, such as active packaging or cosmetics. The morphological analysis of the polymer composites, prepared using a discontinuous mechanical mixer, revealed the presence of macroaggregates and nano-lamellae at the polymer interface. This resulted in an enhanced water vapor permeability compared to the original blend. Furthermore, the migration kinetics of active molecules from the thin films confirmed a controlled release mechanism based on their immobilization within the lamellar system. Scaling-up experiments evaluated the materials' morphology and mechanical and thermal properties. Remarkably, stretching deformation and a higher shear rate during the mixing process enhanced the dispersion and distribution of the nanocarriers, as confirmed by the favorable mechanical properties of the materials.

Green Routes for Bio-Fabrication in Biomedical and Pharmaceutical Applications

In the last decade, significant advances in nanotechnologies, rising from increasing knowledge and refining of technical practices in green chemistry and bioengineering, enabled the design of innovative devices suitable for different biomedical applications. In particular, novel bio-sustainable methodologies are developing to fabricate drug delivery systems able to sagely mix properties of materials (i.e., biocompatibility, biodegradability) and bioactive molecules (i.e., bioavailability, selectivity, chemical stability), as a function of the current demands for the health market. The present work aims to provide an overview of recent developments in the bio-fabrication methods for designing innovative green platforms, emphasizing the relevant impact on current and future biomedical and pharmaceutical applications.

Antimicrobial and Gas Barrier Crustaceans and Fungal Chitin-Based Coatings on Biodegradable Bioplastic Films

Chitin nanofibrils (CN) can be obtained from crustaceans and fungal sources and can be used for preparing coatings for bioplastic films, that are fundamental for developing a safe and sustainable biodegradable food packaging. Coatings with different concentrations of CN from shrimps were applied on different bioplastic substrates, like Poly (butylene succinate-co-adipate)/Poly(3-hydroxybutyrate-co-3-hydroxyvalerate (PBSA/PHBV) blend, Polybutylene succinate (PBS), and Polybutylene adipate terephthalate/Poly(lactic acid) (PBAT/PLA) blend, but the adhesion to the substrates was scarce. On the contrary, the fungal-based CN showed a better adhesion. Additionally, it was found that the use of an additive based on oligomeric lactic acid was useful to prepare a coating with an improved adhesion to bioplastics. The gas barrier properties to oxygen and water vapour of coated and un-coated films were measured, revealing an improvement of these properties thanks to applied coatings, especially towards the oxygen. Antimicrobial properties and biodegradation capacity were also evaluated revealing an antibacterial effect of the coatings that did not significantly interfere with their biodegradability. The results are discussed and interpreted considering the correlation between composition and macromolecular structures with the observed functional properties.

Bio-Based Poly(lactic acid)/Poly(butylene sebacate) Blends with Improved Toughness

A series of poly(butylene sebacate) (PBSe) aliphatic polyesters were successfully synthesized by the melt polycondensation of sebacic acid (Se) and 1,4-butanediol (BDO), two monomers manufactured on an industrial scale from biomass. The number average molecular weight (M_n) in the range from 6116 to 10,779 g/mol and the glass transition temperature (T_g) of the PBSe polyesters were tuned by adjusting the feed ratio between the two monomers. Polylactic acid (PLA)/PBSe blends with PBSe concentrations between 2.5 to 20 wt% were obtained by melt compounding. For the first time, PBSe’s effect on the flexibility and toughness of PLA was studied. As shown by the torque and melt flow index (MFI) values, the addition of PBSe endowed PLA with both enhanced melt processability and flexibility. The tensile tests and thermogravimetric analysis showed that PLA/PBSe blends containing 20 wt% PBSe obtained using a BDO molar excess of 50% reached an increase in elongation at break from 2.9 to 108%, with a negligible decrease in Young’s modulus from 2186 MPa to 1843 MPa, and a slight decrease in thermal performances. These results demonstrated the plasticizing efficiency of the synthesized bio-derived polyesters in overcoming PLA’s brittleness. Moreover, the tunable properties of the resulting PBSe can be of great industrial interest in the context of circular bioeconomy.

Development of Novel Blown Shrink Films from Poly(Lactide)/Poly(Butylene-Adipate-co-Terephthalate) Blends for Sustainable Food Packaging Applications

Heat-shrinkable films, largely made of polyolefins and widely employed in the packaging sector as collation or barrier films, due to their short service life, are held responsible for high environmental impact. One possible strategy for reduction in their carbon footprint can be the use of biodegradable polymers. Thus, this work aimed to develop novel, heat-shrinkable, fully biodegradable films for green packaging applications and to analyze their functional performance. Films were obtained from blends of amorphous polylactic acid (PLA) and poly(butylene-adipate-co-terephthalate) (PBAT) at different mass ratios and compatibilized with a chain extender. They were produced by means of a lab-scale film blowing extrusion apparatus and characterized in terms of physical–mechanical properties and shrinkability. The influence of the processing parameters during the extrusion blowing process on the films’ behavior was investigated, highlighting the effects of blend composition and stretching drawing conditions. Shrinkage tests demonstrated that the produced films have shrinkability values in the typical range of mono-oriented films (ca. 60–80% in machine direction and ca. 10–20% in transverse direction). Moreover, the shrinkage in machine direction increases both with the mass flow rate, the take-up ratio to blow-up ratio and the bubble cooling of the film blowing process, and with the PLA content into the blend. In particular, films at higher PLA content also exhibit higher transparency and stiffness.

Green Composites from Partially Bio-Based Poly(butylene succinate-co-adipate)-PBSA and Short Hemp Fibers with Itaconic Acid-Derived Compatibilizers and Plasticizers

In this work, green composites have been developed and characterized using a bio-based polymeric matrix such as BioPBSA and the introduction of 30 wt.% short hemp fibers as a natural reinforcement to obtain materials with maximum environmental efficiency. In order to increase the interfacial adhesion between the matrix and the fiber to obtain better properties in the composites, a reactive extrusion process has been carried out. On the one hand, different additives derived from bio-based itaconic acid have been added to the BioPBSA/HEMP composite, such as dibutyl itaconate (DBI) and a copolymer of PBSA grafted with itaconic acid (PBSA-g-IA). On the other hand, a different copolymer of PBSA grafted with maleic anhydride (PBSA-g-MA) was also tested. The resulting composites have been processed by injection-molding to obtain different samples which were evaluated in terms of mechanical, thermal, chemical, dynamic-mechanical, morphological and wettability and color properties. In relation to the mechanical properties, the incorporation of hemp fibers resulted in an increase in the stiffness of the base polymer. The tensile modulus of pure BioPBSA increased from 281 MPa to 3482 MPa with 30% fiber. The addition of DBI shows a remarkable improvement in the ductility of the composites, while copolymers with IA and MA, generate mechanically balanced composites. In terms of thermal properties, the incorporation of hemp fiber and compatibilizing agents led to a reduction in thermal stability. However, from the point of view of thermomechanical properties, a clear increase in rigidity is achieved throughout the temperature range studied. As far as the color of the samples is concerned, the incorporation of hemp generates a typical color, while the incorporation of the compatibilizing agents does not modify this color excessively. Finally, the introduction of lignocellulosic fibers greatly affects water absorption and contact angle, although the use of additives helped to mitigate this effect.

Progress in the Degradability of Biodegradable Film Materials for Packaging

In today’s world, the problem of “white pollution” is becoming more and more serious, and many countries have paid special attention to this problem, and it has become one of the most important tasks to reduce polymer waste and to protect the environment. Due to the degradability, safety, economy and practicality of biodegradable packaging film materials, biodegradable packaging film materials have become a major trend in the packaging industry to replace traditional packaging film materials, provided that the packaging performance requirements are met. This paper reviews the degradation mechanisms and performance characteristics of biodegradable packaging film materials, such as photodegradation, hydrodegradation, thermo-oxidative degradation and biodegradation, focuses on the research progress of the modification of biodegradable packaging film materials, and summarizes some challenges and bottlenecks of current biodegradable packaging film materials.

The Use of Branching Agents in the Synthesis of PBAT

Biodegradable polyesters represent an advanced alternative to polyolefin plastics in various applications. Polybutylene adipate terephthalate (PBAT) can compete with polyolefins in terms of their mechanical characteristics and melt processing conditions. The properties of PBAT depend on the molecular weight, dispersity, and architecture of the copolymer. Long-chain branching (LCB) of the PBAT backbone is an efficient method for the improvement of the copolymer characteristics. In the present work, we studied branching agents (BAs) 1–7 of different structures in the two-stage polycondensation of 1,4-butanediol, dimethyl terephthalate, and adipic acid and investigated the composition and melt rheology of the copolymers. According to the results of the research, 1,1,1-tris(hydroxymethyl)ethane 2 and 3-hydroxy-2-(hydroxymethyl)-2-methylpropanoic acid 5 outperformed glycerol 1 as BAs in terms of shear thinning behavior and viscoelasticity.

A Brief Review of Poly (Butylene Succinate) (PBS) and Its Main Copolymers: Synthesis, Blends, Composites, Biodegradability, and Applications

PBS, an acronym for poly (butylene succinate), is an aliphatic polyester that is attracting increasing attention due to the possibility of bio-based production, as well as its balanced properties, enhanced processability, and excellent biodegradability. This brief review has the aim to provide the status concerning the synthesis, production, thermal, morphological and mechanical properties underlying biodegradation ability, and major applications of PBS and its principal copolymers.

Experimental Determination of Molecular Weight-Dependent Miscibility of PBAT/PLA Blends

Blends of poly(butylene adipate-co-terephthalate) (PBAT) and polylactide (PLA) have attracted the attention of academia and industry as a sustainable material. Unfortunately, this combination results in problems related to poor miscibility on the molecular level. This study mainly aims to determine the influence of molecular weights on the miscibility of PBAT/PLA blends. First, polymers with various molecular weights were obtained by the hydrolysis of PBAT and methanolysis of PLA. Second, the two components were solution-blended with different molecular weights and weight ratios. Third, each blend was heated to the molten state and subsequently stored at room temperature. Finally, the samples were tested using DSC and SEM. The thermal analysis indicated that the difference in glass transition temperature between both components decreased from about 91 °C to 57 °C and 0 °C, as the number-average molecular weights (M_n) decreased from 52/127 to 9.4/9 and 6.3/6.6 kg/mol. Moreover, the morphology changed from phase-separated with dispersed large particles gradually to uniform and homogeneous. This experimental work validated the trends predicted in the previous study, namely that PBAT/PLA blends changed the state from immiscible to partially miscible to fully miscible with decreasing M_n values. Moreover, we discussed the influencing factors such as weight ratio, temperature, and molecular structure on the miscibility. Based on the results, this work contributes to developing partially miscible and compatible blends without additives.

Jamil SNA, Abdan K. A Brief Review on the Influence of Ionic Liquids on the Mechanical, Thermal, and Chemical Properties of Biodegradable Polymer Composites

Biodegradable polymers are an exceptional class of polymers that can be decomposed by bacteria. They have received significant interest from researchers in several fields. Besides this, biodegradable polymers can also be incorporated with fillers to fabricate biodegradable polymer composites. Recently, a variety of ionic liquids have also been applied in the fabrication of the polymer composites. In this brief review, two types of fillers that are utilized for the fabrication of biodegradable polymer composites, specifically organic fillers and inorganic fillers, are described. Three types of synthetic biodegradable polymers that are commonly used in biodegradable polymer composites, namely polylactic acid (PLA), polybutylene succinate (PBS), and polycaprolactone (PCL), are reviewed as well. Additionally, the influence of two types of ionic liquid, namely alkylimidazolium- and alkylphosphonium-based ionic liquids, on the mechanical, thermal, and chemical properties of the polymer composites, is also briefly reviewed. This review may be beneficial in providing insights into polymer composite investigators by enhancing the properties of biodegradable polymer composites via the employment of ionic liquids.