Reduced Graphene Oxide Modified the Interdigitated Chain Electrode for an Insulin Sensor

Capacitive biosensors for label-free and ultrasensitive detection of biomarkers

Capacitive biosensors are label-free capacitors that can detect biomarkers with the outstanding advantages of simplicity, low cost, and ultrahigh sensitivity. A typical capacitive biosensor consists of a bioreceptor and a transducer, where the bioreceptor captures the biomarker to form a bioreceptor/biomarker conjugate and the transducer generates a detectable signal. In general, antibodies, aptamers, or proteins are exploited as the bioreceptor, while various electrodes including carbon electrodes (CEs), gold electrodes (AuEs), or interdigitated electrodes (IDEs) may serve as the transducer. Because the formation of bioreceptor/biomarker conjugates often leads to a change in capacitance, the capacitive signal is then employed for biomarker detection. This review summarizes recent advances in capacitive biosensors for the detection of biomarkers over the last five years. With a focus on the three common types of bioreceptors, i.e., antibodies, aptamers, and proteins, capacitive biosensors using CEs, AuEs, and IDEs as the transducers are discussed in detail. The immobilization of bioreceptors and signal amplification strategies are described to provide a robust overview of capacitive biosensors for biomarker detection. In addition, analytical methods and future prospects are given to support the application of capacitive biosensors.

Electrochemical impedance-based biosensor for label-free determination of plasma P-tau181 levels for clinically accurate diagnosis of mild cognitive impairment and Alzheimer's disease

Plasma phosphorylated-tau threonine 181 (p-tau181) is a promising biomarker for predicting Alzheimer's disease (AD) and mild cognitive impairment (MCI), which is the symptomatic pre-dementia stage of AD. To date, there are limitations in the current diagnosis and classification of the two stages of MCI and AD in clinical practice remain a dilemma. In this study, we aimed to discriminate and diagnose patients with MCI, AD, and healthy participants based on the accurate, label-free, and ultrasensitive detection of p-tau181 levels in human clinical plasma samples using our developed electrochemical impedance-based biosensor, which allows to detect p-tau181 at a very low concentration of 0.92 fg mL^-1. Human plasma samples were collected from 20 patients with AD, 20 patients with MCI, and 20 individuals with healthy control. The change in charge-transfer resistance of the developed impedance-based biosensor caused by capturing p-tau181 in plasma samples was recorded to evaluate the determination of plasma p-tau181 levels in human clinical samples for discrimination and diagnosis of AD, MCI, and healthy control individuals, respectively. Receiver operating characteristic (ROC) curve, a standard analysis to judge the clinically diagnostic capability of our biosensor platform based on the estimated levels of plasma p-tau181, resulted a sensitivity of 95%, a specificity of 85%, the area under the ROC curve (AUC) value of 0.94 of the accuracy for discriminating AD patients from healthy controls; a sensitivity of 70%, a specificity of 70%, the AUC of 0.75 to discriminate MCI patients from healthy controls. Statistical analysis (one-way analysis of variance (ANOVA)) was used to compare the estimated plasma p-tau181 levels in clinical samples, indicated significantly higher for AD patients with healthy controls (***p ≤ 0.001), AD with MCI patients (***p ≤ 0.001), and MCI patients with healthy controls (*p ≤ 0.05), respectively. In addition, we compared our sensor to the global cognitive function scales and discovered that it performed noticeably improvement in diagnosing the stages of AD. These results demonstrated the good application of our developed electrochemical impedance-based biosensor in the identification of clinical disease stages. Moreover, in this study, a small dissociation constant (K_D) of 0.533 pM was first determined to evaluate the high binding affinity between the p-tau181 biomarker and its antibody, providing a reference parameter for future studies of the p-tau181 biomarker and AD.

Electrochemical Immunosensor for the Early Detection of Rheumatoid Arthritis Biomarker: Anti-Cyclic Citrullinated Peptide Antibody in Human Serum Based on Avidin-Biotin System

Rheumatoid arthritis (RA) is a chronic autoimmune disease that produces a progressive inflammatory response that leads to severe pain, swelling, and stiffness in the joints of hands and feet, followed by irreversible damage of the joints. The authors developed a miniaturized, label-free electrochemical impedimetric immunosensor for the sensitive and direct detection of arthritis Anti-CCP-ab biomarker. An interdigitated-chain-shaped microelectrode array (ICE) was fabricated by taking the advantage of microelectromechanical systems. The fabricated ICE was modified with a self-assembled monolayer (SAM) of Mercaptohexanoic acid (MHA) for immobilization of the synthetic peptide bio-receptor (B-CCP). The B-CCP was attached onto the surface of SAM modified ICE through a strong avidin-biotin bio-recognition system. The modified ICE surface with the SAM and bio-molecules (Avidin, B-CCP, Anti-CCP-ab and BSA) was morphologically and electrochemically characterized. The change in the sensor signal upon analyte binding on the electrode surface was probed through the electrochemical impedance spectroscopy (EIS) property of charge-transfer resistance (R_ct) of the modified electrodes. EIS measurements were target specific and the sensor response was linearly increased with step wise increase in target analyte (Anti-CCP-ab) concentrations. The developed sensor showed a linear range for the addition of Anti-CCP-ab between 1 IU mL⁻¹ → 800 IU mL⁻¹ in phosphate buffered saline (PBS) and Human serum (HS), respectively. The sensor showed a limit of detection of 0.60 IU mL⁻¹ and 0.82 IU mL⁻¹ in the PBS and HS, respectively. The develop bio-electrode showed a good reproducibility (relative standard deviation (RSD), 1.52%), selectivity and stability (1.5% lost at the end of 20th day) with an acceptable recovery rate (98.0% → 101.18%) and % RSD’s for the detection of Anti-CCP-ab in spiked HS samples.

Interdigitated and Wave-Shaped Electrode-Based Capacitance Sensor for Monitoring Antibiotic Effects

Label-free and real-time monitoring of the bacterial viability is essential for the accurate and sensitive characterization of the antibiotic effects. In the present study, we investigated the feasibility of the interdigitated and wave-shaped electrode (IWE) for monitoring the effect of tetracycline or kanamycin on Staphylococcus aureus (S. aureus) and methicillin-resistant S.aureus (MRSA). The electrical impedance spectra of the IWE immersed in the culture media for bacterial growth were characterized in a frequency range of 10 Hz to 1 kHz. The capacitance index (CI) (capacitance change relevant with the bacterial viability) was used to monitor the antibiotic effects on the S. aureus and MRSA in comparison to the traditional methods (disk diffusion test and optical density (OD) measurement). The experimental results showed that the percentage of change in CI (PCI) for the antibiotic effect on MRSA was increased by 51.58% and 57.83% in kanamycin and control, respectively. In contrast, the PCI value decreased by 0.25% for tetracycline, decreased by 52.63% and 37.66% in the cases of tetracycline and kanamycin-treated S. aureus, and increased 2.79% in the control, respectively. This study demonstrated the feasibility of the IWE-based capacitance sensor for the label-free and real-time monitoring of the antibiotic effects on S. aureus and MRSA.

Bioelectrocatalysis of Hemoglobin on Electrodeposited Ag Nanoflowers toward H2O2 Detection

Hydrogen peroxide (H2O2) is a partially reduced metabolite of oxygen that exerts a diverse array of physiological and pathological activities in living organisms. Therefore, the accurate quantitative determination of H2O2 is crucial in clinical diagnostics, the food industry, and environmental monitoring. Herein we report the electrosynthesis of silver nanoflowers (AgNFs) on indium tin oxide (ITO) electrodes for direct electron transfer of hemoglobin (Hb) toward the selective quantification of H2O2. After well-ordered and fully-grown AgNFs were created on an ITO substrate by electrodeposition, their morphological and optical properties were analyzed with scanning electron microscopy and UV-Vis spectroscopy. Hb was immobilized on 3-mercaptopropionic acid-coated AgNFs through carbodiimide cross-linking to form an Hb/AgNF/ITO biosensor. Electrochemical measurement and analysis demonstrated that Hb retained its direct electron transfer and electrocatalytic properties and acted as a H2O2 sensor with a detection limit of 0.12 µM and a linear detection range of 0.2 to 3.4 mM in phosphate-buffered saline (PBS). The sensitivity, detection limit, and detection range of the Hb/AgNF/ITO biosensor toward detection H2O2 in human serum was also found to be 0.730 mA mM-1 cm-2, 90 µM, and 0.2 to 2.6 mM, indicating the clinical application for the H2O2 detection of the Hb/AgNF/ITO biosensor. Moreover, interference experiments revealed that the Hb/AgNF/ITO sensor displayed excellent selectivity for H2O2.

Laser-induced graphene interdigitated electrodes for label-free or nanolabel-enhanced highly sensitive capacitive aptamer-based biosensors

Highly porous laser-induced graphene (LIG) is easily generated in complex electrode configurations such as interdigitated electrodes (IDEs). Here, we demonstrate that their superior capacitive response at low frequencies can be exploited in affinity biosensors using thrombin aptamers as model biorecognition elements. Of specific interest was the effect of electrode surface area on capacitance detection, and the comparison between a label-free format and enhancement strategies afforded by carboxy group bearing polymeric nanoparticles or liposomes. Electrochemical impedance spectroscopy (EIS) was used to investigate the LIG performance and optimize the biosensor design. Interestingly, the label-free strategy performed extremely well and additional labels decreased the limit of detection or increased the sensitivity only minimally. It is assumed that the highly porous nature of the LIG structures dominates the capacitive response so that labels removed from the surface have only limited influence Also, while slight performance changes can be observed for smaller vs. larger electrode structures, the performance of a LIG IDE is reasonably independent of its size. In the end, a dynamic range of 5 orders of magnitude was obtained (0.01 nM-1000 nM) with a limit of detection as low as 0.12 pM. When measured in serum, this increased to 1.3 pM. The good reproducibility (relative standard deviation (RSD), 4.90%) and repeatability (RSD, 2.59%) and good long-term stability (>7 weeks at 4 °C) prove that a LIG-based capacitance sensor is an excellent choice for affinity-based biosensor. The ease-of-production, the simplicity of modification and the superior performance even in a label-free format indicate that LIG-based biosensors should be considered in point-of-care diagnostics in the future.

Electrochemical Detection of C-Reactive Protein in Human Serum Based on Self-Assembled Monolayer-Modified Interdigitated Wave-Shaped Electrode

An electrochemical capacitance immunosensor based on an interdigitated wave-shaped micro electrode array (IDWµE) for direct and label-free detection of C-reactive protein (CRP) was reported. A self-assembled monolayer (SAM) of dithiobis (succinimidyl propionate) (DTSP) was used to modify the electrode array for antibody immobilization. The SAM functionalized electrode array was characterized morphologically by atomic force microscopy (AFM) and energy dispersive X-ray spectroscopy (EDX). The nature of gold-sulfur interactions on SAM-treated electrode array was probed by X-ray photoelectron spectroscopy (XPS). The covalent linking of anti-CRP-antibodies onto the SAM modified electrode array was characterized morphologically through AFM, and electrochemically through cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The application of phosphate-buffered saline (PBS) and human serum (HS) samples containing different concentrations of CRP in the electrode array caused changes in the electrode interfacial capacitance upon CRP binding. CRP concentrations in PBS and HS were determined quantitatively by measuring the change in capacitance (ΔC) through EIS. The electrode immobilized with anti-CRP-antibodies showed an increase in ΔC with the addition of CRP concentrations over a range of 0.01-10,000 ng mL-1. The electrode showed detection limits of 0.025 ng mL-1 and 0.23 ng mL-1 (S/N = 3) in PBS and HS, respectively. The biosensor showed a good reproducibility (relative standard deviation (RSD), 1.70%), repeatability (RSD, 1.95%), and adequate selectivity in presence of interferents towards CRP detection. The sensor also exhibited a significant storage stability of 2 weeks at 4 °C in 1× PBS.

Graphene Nanomaterials-Based Radio-Frequency/Microwave Biosensors for Biomaterials Detection

In this paper, the advances in radio-frequency (RF)/microwave biosensors based on graphene nanomaterials including graphene, graphene oxide (GO), and reduced graphene oxide (rGO) are reviewed. From a few frontier studies, recently developed graphene nanomaterials-based RF/microwave biosensors are examined in-depth and discussed. Finally, the prospects and challenges of the next-generation RF/microwave biosensors for wireless biomedical applications are proposed.

Towards Point-of-Care Insulin Detection

Good glucose management through an insulin dose regime based on the metabolism of glucose helps millions of people worldwide manage their diabetes. Since Banting and Best extracted insulin, glucose management has improved due to the introduction of insulin analogues that act from 30 minutes to 28 days, improved insulin dose regimes, and portable glucose meters, with a current focus on alternative sampling sites that are less invasive. However, a piece of the puzzle is still missing-the ability to measure insulin directly in a Point-of-Care device. The ability to measure both glucose and insulin concurrently will enable better glucose control by providing an improved estimate for insulin sensitivity, minimizing variability in control, and maximizing safety from hypoglycaemia. However, direct detection of free insulin has provided a challenge due to the size of the molecule, the low concentration of insulin in blood, and the selectivity against interferants in blood. This review summarizes current insulin detection methods from immunoassays to analytical chemistry, and sensors. We also discuss the challenges and potential of each of the methods towards Point-of-Care insulin detection.

Impedimetric phosphorene field-effect transistors for rapid detection of lead ions

Stimuli-responsive field-effect transistors (FETs) based on 2D nanomaterials have been considered as attractive candidates for sensing applications due to their rapid response, high sensitivity, and real-time monitoring capabilities. Here we report on an impedance spectroscopy technique for FET sensor applications with ultra-high sensitivity and good reproducibility. An alumina-gated FET, using an ultra-thin black phosphorus flake as the channel material, shows significantly improved stability and ultra-high sensitivity to lead ions in water. In addition, the phase angle in the low frequency region was found to change significantly in the presence of lead ion solutions, whereas it was almost unchanged in the high frequency region. The dominant sensing performance was found at low frequency phase spectrum around 50 Hz and a systematic change in the phase angle in different lead ion concentrations was found. Applying the impedance spectroscopy technique to insulator-gated FET sensors could open a new avenue for real-world sensor applications.

Label-Free Impedance Sensing of Aflatoxin B₁ with Polyaniline Nanofibers/Au Nanoparticle Electrode Array

Aflatoxin B1 (AFB₁) is produced by the Aspergillus flavus and Aspergillus parasiticus group of fungi which is most hepatotoxic and hepatocarcinogenic and occurs as a contaminant in a variety of foods. AFB₁ is mutagenic, teratogenic, and causes immunosuppression in animals and is mostly found in peanuts, corn, and food grains. Therefore, novel methodologies of sensitive and expedient strategy are often required to detect mycotoxins at the lowest level. Herein, we report an electrochemical impedance sensor that selectively detects AFB₁ at the lowest level by utilizing polyaniline nanofibers (PANI) coated with gold (Au) nanoparticles composite based indium tin oxide (ITO) disk electrodes. The Au-PANI nanocomposites were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) spectroscopy, and electrochemical impedance spectroscopy (EIS). The composite electrode exhibited a 14-fold decrement in |Z|1Hz in comparison with the bare electrode. The Au-PANI acted as an effective sensing platform having high surface area, electrochemical conductivity, and biocompatibility which enabled greater loading deposits of capture antibodies. As a result, the presence of AFB₁ was screened with high sensitivity and stability by monitoring the changes in impedance magnitude (|Z|) in the presence of a standard iron probe which was target specific and proportional to logarithmic AFB₁ concentrations (CAFB₁). The sensor exhibits a linear range 0.1 to 100 ng/mL with a detection limit (3) of 0.05 ng/mL and possesses good reproducibility and high selectivity against another fungal mycotoxin, Ochratoxin A (OTA). With regard to the practicability, the proposed sensor was successfully applied to spiked corn samples and proved excellent potential for AFB₁ detection and development of point-of-care (POC) disease sensing applications.

Non-invasive, in vitro analysis of islet insulin production enabled by an optical porous silicon biosensor

A label-free porous silicon (pSi) based, optical biosensor, using both an antibody and aptamer bioreceptor motif has been developed for the detection of insulin. Two parallel biosensors were designed and optimised independently, based on each bioreceptor. Both bioreceptors were covalently attached to a thermally hydrosilylated pSi surface though amide coupling, with unreacted surface area rendered stable and low fouling by incorporation of PEG moieties. The insulin detection ability of each biosensor was determined using interferometric reflectance spectroscopy, using a range of different media both with and without serum. Sensing performance was compared in terms of response value, response time and limit of detection (LOD) for each platform. In order to demonstrate the capability of the best performing biosensor to detect insulin from real samples, an in vitro investigation with the aptamer-modified surface was performed. This biosensor was exposed to buffer conditioned by glucose-stimulated human islets, with the result showing a positive response and a high degree of selectivity towards insulin capture. The obtained results correlated well with the ELISA used in the clinic for assaying glucose-stimulated insulin release from donor islets. We anticipate that this type of sensor can be applied as a rapid point-of-use biosensor to assess the quality of donor islets in terms of their insulin production efficiency, prior to transplantation.