TiO2-x/TiO2-Structure Based 'Self-Heated' Sensor for the Determination of Some Reducing Gases

A double defects-dominated flexible TiO2 matrix for in-situ SERS sensing of antibiotic residues in aquatic ecosystem (fish & fishpond water) and their on-site degradation in flowing water

High-performance flexible semiconductor material can be used as an excellent multifunctional matrix for in-situ ultrasensitive surface-enhanced Raman scattering (SERS) detection and synchronous photocatalytic degradation of antibiotic residues in aquatic ecosystem. Here, a calcium-doped TiO2 flexible matrix with double defects (surface oxygen vacancy defect and Ti3+ energy level defect) was developed by its "in-situ one-step" hydrothermal synthesis on cotton fabric for the above purposes. Due to the joint contribution of double defects, a multi-channel charge transfer mode and a high-efficiency carrier separation are achieved, which endows flexible cotton fabric/Ca-doped TiO2 (Cot/Ca-TiO2) substrate with the greatly boosted SERS effect for in-situ detection of antibiotic residues on fish body surface and in fishpond water by a simple wiping or dipping sampling method, even for simultaneous identification of multi-component residues. The detection limits of three antibiotic residues (enrofloxacin, ciprofloxacin and enoxacin) are as low as 10-9 M, which are far lower than the EU standard. More meaningfully, the flexible Cot/Ca-TiO2 can be used as a multifunctional filter-membrane type photocatalyst for efficient on-site degradation of antibiotic residues in flowing fishpond water by a multi-grade photocatalysis means. Moreover, the flexible matrix exhibits good recyclability in both actual detection and photocatalysis.

Flexible Antibacterial Respiratory Monitoring Sensor Based on Controllable Au-Modified Surface of Highly {001} Preferred Anatase Titanium Dioxide Thin Film

Respiratory signals are critical clinical diagnostic criteria for respiratory diseases and health conditions, and respiratory sensors play a crucial role in achieving the desired respiratory monitoring effect. High sensitivity to a single factor can improve the reliability of respiratory monitoring, and maintaining the hygiene of the sensors is also important for daily health monitoring. Herein, we propose a flexible Au-modified anatase titanium dioxide resistive respiratory sensor, which can be mechanically compliantly attached to curved surfaces for respiratory monitoring in different modalities (i.e., respiratory intensity, frequency, and rate). The uniform and preferentially oriented anatase titanium dioxide films gained by the polymer-assisted deposition technique can be fabricated on flexible substrates through a liquid-assisted transferring process. The Au modification can enhance surface plasmon resonance to facilitate the photocatalytic activity of titanium dioxide, and the optimized distribution of Au on the surface of titanium dioxide film made the sensor have an excellent antibacterial effect. The uniquely designed encapsulation can effectively control the contact between the surface of titanium dioxide films and electrodes, allowing the flexible sensor to exhibit fast response time (0.71 s) and recovery time (1.06 s) to respiratory as well as insensitivity or low sensitivity to other factors (i.e., gas composition, humidity, temperature, stress, and strain). This work provided an effective strategy for flexible wearable respiratory sensors and has great potential in daily respiratory monitoring for health management and pandemic control.

The mechanism and reaction kinetics of visible light active bismuth oxide deposited on titanium vanadium oxide for aqueous diclofenac photocatalysis

Non-uniform, non-spherical bismuth oxide deposited on titanium vanadium oxide (3%-BVT1) was successfully synthesized via co-precipitation method and assessed for visible light degradation of aqueous diclofenac. The synthesized photocatalysts were characterized using X-ray diffraction, diffuse reflectance spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy, and high-resolution transmission electron microscopy. Up to 80.7% diclofenac degradation was observed with a significant increment in reaction rate compared to commercially available Degussa P25 (kapp = 0.0013 → 0.0083 min-1) achieved within 3 h treatment time under optimized parameters of diclofenac concentration (10 mg L-1), catalyst loading (0.1 g L-1), and pH (5). The enhanced photocatalysis could be due to electron-hole separation and contribution of powerful oxidative species •OH > O2•-  > h+  >  > e-. The recyclability experiments indicate that 3%-BVT1 retained its efficiency up to 74.1% over five reaction cycles. Gas chromatography-mass spectrometry analysis indicated the formation of several transformation products during the degradation pathway. The studies of interfering ions depicted mild interference by sulfates, while interference by phosphates and nitrates was negligible during photocatalytic process, i.e., 70, 78.01, and 78.43% for the selected concentrations of 50, 25, and 40 mg L-1 as per their maximum concentrations detected in the natural wastewaters. Thus, 3%-BVT1 is a potential versatile candidate to treat various organic pollutants including pharmaceuticals.

MXene-Based Chemo-Sensors and Other Sensing Devices

MXenes have received worldwide attention across various scientific and technological fields since the first report of the synthesis of Ti3C2 nanostructures in 2011. The unique characteristics of MXenes, such as superior mechanical strength and flexibility, liquid-phase processability, tunable surface functionality, high electrical conductivity, and the ability to customize their properties, have led to the widespread development and exploration of their applications in energy storage, electronics, biomedicine, catalysis, and environmental technologies. The significant growth in publications related to MXenes over the past decade highlights the extensive research interest in this material. One area that has a great potential for improvement through the integration of MXenes is sensor design. Strain sensors, temperature sensors, pressure sensors, biosensors (both optical and electrochemical), gas sensors, and environmental pollution sensors targeted at volatile organic compounds (VOCs) could all gain numerous improvements from the inclusion of MXenes. This report delves into the current research landscape, exploring the advancements in MXene-based chemo-sensor technologies and examining potential future applications across diverse sensor types.

Nanostructure-Based Solution Sensor Fabricated with p-CuOx/n-TiO2 Nanojunctions To Identify Species and Concentrations of Alcohol Molecules

Chemiresistive sensors fabricated based on metal-oxide-semiconductors, the most widely used high-sensitivity sensor materials, are required for detecting target solutions and gases and identifying them with a high degree of accuracy. In this study, we used p-n nanojunctions and nanowire shapes for identifying alcohol solutions. The solution sensors fabricated based on CuOx nanowires with p-CuOx/n-TiO2 nanojunctions detected ethanol, ethylene glycol, and diethylene glycol solutions via DC voltage and electrochemical impedance measurements. The p-n nanojunctions affected the sensors' sensitivity in the diethylene glycol solution, and the nanowire surface areas affected the relaxation time in ethanol and ethylene glycol solutions. To identify alcohol solutions, principal component analysis was performed based on the relationship between the sensor information, such as the presence of p-n nanojunctions and nanowire surface areas, and the sensing performance. This analysis identified alcohol molecular species and predicted alcohol-solution concentrations in the 0.1-20 vol % range with a high degree of accuracy. The concept of using sensors with different surface conditions with respect to p-n nanojunctions and nanowire surface areas offers designs for metal-oxide-semiconductor sensors to identify various molecules in solution.

A Review: Synthesis and Applications of Titanium Sub-Oxides

Magnéli phase titanium oxides, also called titanium sub-oxides (TinO2n-1, 4 < n < 9), are a series of electrically conducting ceramic materials. The synthesis and applications of these materials have recently attracted tremendous attention because of their applications in a number of existing and emerging areas. Titanium sub-oxides are generally synthesized through the reduction of titanium dioxide using hydrogen, carbon, metals or metal hydrides as reduction agents. More recently, the synthesis of nanostructured titanium sub-oxides has been making progress through optimizing thermal reduction processes or using new titanium-containing precursors. Titanium sub-oxides have attractive properties such as electrical conductivity, corrosion resistance and optical properties. Titanium sub-oxides have played important roles in a number of areas such as conducting materials, fuel cells and organic degradation. Titanium sub-oxides also show promising applications in batteries, solar energy, coatings and electronic and optoelectronic devices. Titanium sub-oxides are expected to become more important materials in the future. In this review, the recent progress in the synthesis methods and applications of titanium sub-oxides in the existing and emerging areas are reviewed.

Polyvinylpyrrolidone/TiO2 composites' preparation via sol-gel procedure furthered with non-enzymatic glucose sensing and antibacterial effectiveness

An amperometric non-enzymatic glucose sensing based on polyvinylpyrrolidone and titanium dioxide nanocomposites (PVP-TiO2 NCs) fabricated over stainless-steel (SS) electrode was experimented. The electrode was fabricated of PVP-TiO2 NCs onto SS surface through drop casting coating. The NCs and the electrode were analyzed using Fourier transform infrared (FTIR) and UV-visible (UV-Vis) spectroscopy, X-ray diffraction spectra (XRD), X-ray photoelectron spectra (XPS), particle analyzer, scanning electron microscopy (SEM), EDS and transmission electron microscopy (TEM) and Brunauer-Emmett-Teller (BET) analysis for surface. For electrochemical investigation, cyclic voltammetry, electrochemical impedance spectra, including Nyquist plots and Bode plots, and chronoamperometry were adopted. PVP-TiO2/SS-modified electrode manifested high sensitivity of 360.13 µA/mM.cm2, lower detection limit of 756.8 µM and 0 to 13 mM linear range with regression coefficient of R2 = 0.992. The electrode exhibited high stability with good anti-interference tendency against fructose, uric acid, ascorbic acid and sucrose. The modified electrode also performed well in real sample glucose detection. Further, PVP-TiO2 NCs performed appreciably toward antibacterial studies against some Gram-positive and Gram-negative deleterious bacteria, Escherichia coli, Klebsiella pneumoniae, Staphylococcus aureus, Shigella flexneri microbes.

Recent Advancements in TiO2 Nanostructures: Sustainable Synthesis and Gas Sensing

The search for sustainable technology-driven advancements in material synthesis is a new norm, which ensures a low impact on the environment, production cost, and workers' health. In this context, non-toxic, non-hazardous, and low-cost materials and their synthesis methods are integrated to compete with existing physical and chemical methods. From this perspective, titanium oxide (TiO₂) is one of the fascinating materials because of its non-toxicity, biocompatibility, and potential of growing by sustainable methods. Accordingly, TiO₂ is extensively used in gas-sensing devices. Yet, many TiO₂ nanostructures are still synthesized with a lack of mindfulness of environmental impact and sustainable methods, which results in a serious burden on practical commercialization. This review provides a general outline of the advantages and disadvantages of conventional and sustainable methods of TiO₂ preparation. Additionally, a detailed discussion on sustainable growth methods for green synthesis is included. Furthermore, gas-sensing applications and approaches to improve the key functionality of sensors, including response time, recovery time, repeatability, and stability, are discussed in detail in the latter parts of the review. At the end, a concluding discussion is included to provide guidelines for the selection of sustainable synthesis methods and techniques to improve the gas-sensing properties of TiO₂.

Room-temperature ammonia gas sensing via Au nanoparticle-decorated TiO2 nanosheets

A high-performance gas sensor operating at room temperature is always favourable since it simplifies the device fabrication and lowers the operating power by eliminating a heater. Herein, we fabricated the ammonia (NH₃) gas sensor by using Au nanoparticle-decorated TiO₂ nanosheets, which were synthesized via two distinct processes: (1) preparation of monolayer TiO₂ nanosheets through flux growth and a subsequent chemical exfoliation and (2) decoration of Au nanoparticles on the TiO₂ nanosheets via hydrothermal method. Based on the morphological, compositional, crystallographic, and surface characteristics of this low-dimensional nano-heterostructured material, its temperature- and concentration-dependent NH₃ gas-sensing properties were investigated. A high response of ~ 2.8 was obtained at room temperature under 20 ppm NH₃ gas concentration by decorating Au nanoparticles onto the surface of TiO₂ nanosheets, which generated oxygen defects and induced spillover effect as well.

Green production of titanium dioxide nanometric particles through electrolytic anodic dissolution of titanium metal

Nanometric titanium derivatives such as hydroxide and dioxide compounds have a great attention because they are significant industrial material of commercial importance and applications in photocatalyst, semiconductors, and wastewater treatment. The present investigation gives the results of anodic dissolution preparation of titanium hydroxide nanometric particles followed by calcination for complete conversion to nanometric titanium dioxide product. The optimum conditions for the anodic dissolution of titanium metal were pH 4, C.D. 65 mA/cm², 25 °C, 150 rpm, electrode gap distance 3 cm, and NaCl 3 g/l for electrolysis time 240 min and thermally calcinated at 600 °C for 240 min., to reach complete conversion to anatase titanium dioxide nanopowder of main particles size of 77 nm with major percentage of 70%. Chemical and physical characterizations were carried out for evaluation of the obtained products including transmission electron microscope, EDX, XRD, and the scanning advanced electronic diffraction pattern. Preliminary economic indicators were calculated to show that the capital cost of the plant is $1.613 million, with annual operating cost of $0.915 million which means the required investment is $2.528 million. The operating cost for the production of nanometric anatase TiO₂ is $30.5/kg with depreciation excluding the land price.

Assessment of TiO2 Nanoparticle Impact on Surface Morphology of Chinese Hamster Ovary Cells

The process of nanoparticles entering the cells of living organisms is an important step in understanding the influence of nanoparticles on biological processes. The interaction of nanoparticles with the cell membrane is the first step in the penetration of nanoparticles into cells; however, the penetration mechanism is not yet fully understood. This work reported the study of the interaction between TiO₂ nanoparticles (TiO₂-NPs) and Chinese hamster ovary (CHO) cells using an in vitro model. The characterization of crystalline phases of TiO₂ NPs was evaluated by transmission electron microscopy (TEM), X-ray diffraction (XRD) spectrum, and atomic force microscopy (AFM). Interaction of these TiO₂ nanoparticles (TiO₂- NPs) with the CHO cell membrane was investigated using atomic force microscopy (AFM) and Raman spectroscopy. The XRD analysis result showed that the structure of the TiO₂ particles was in the rutile phase with a crystallite size of 60 nm, while the AFM result showed that the particle size distribution had two peaks with 12.1 nm and 60.5 nm. The TEM analysis confirmed the rutile phase of TiO₂ powder. Our study showed that exposure of CHO cells to TiO₂-NPs caused morphological changes in the cell membranes and influenced the viability of cells. The TiO₂-NPs impacted the cell membrane surface; images obtained by AFM revealed an ‘ultra structure‘ with increased roughness and pits on the surface of the membrane. The depth of the pits varied in the range of 40–80 nm. The maximal depth of the pits after the treatment with TiO₂-NPs was 100% higher than the control values. It is assumed that these pits were caveolae participating in the endocytosis of TiO₂-NPs. The research results suggest that the higher maximal depth of the pits after the exposure of TiO₂-NPs was determined by the interaction of these TiO₂-NPs with the cell’s plasma membrane. Moreover, some of pits may have been due to plasma membrane damage (hole) caused by the interaction of TiO₂-NPs with membrane constituents. The analysis of AFM images demonstrated that the membrane roughness was increased with exposure time of the cells to TiO₂-NPs dose. The average roughness after the treatment for 60 min with TiO₂-NPs increased from 40 nm to 78 nm. The investigation of the membrane by Raman spectroscopy enabled us to conclude that TiO₂-NPs interacted with cell proteins, modified their conformation, and potentially influenced the structural damage of the plasma membrane.

Gas Sensors Based on Titanium Oxides (Review)

Nanostructured titanium compounds have recently been applied in the design of gas sensors. Among titanium compounds, titanium oxides (TiO2) are the most frequently used in gas sensing devices. Therefore, in this review, we are paying significant attention to the variety of allotropic modifications of titanium oxides, which include anatase, rutile, brukite. Very recently, the applicability of non-stoichiometric titanium oxide (TiO2−x)-based layers for the design of gas sensors was demonstrated. For this reason, in this review, we are addressing some research related to the formation of non-stoichiometric titanium oxide (TiO2−x) and Magnéli phase (TinO2n−1)-based layers suitable for sensor design. The most promising titanium compounds and hetero- and nano-structures based on these compounds are discussed. It is also outlined that during the past decade, many new strategies for the synthesis of TiO2 and conducting polymer-based composite materials were developed, which have found some specific application areas. Therefore, in this review, we are highlighting how specific formation methods, which can be used for the formation of TiO2 and conducting polymer composites, can be applied to tune composite characteristics that are leading towards advanced applications in these specific technological fields. The possibility to tune the sensitivity and selectivity of titanium compound-based sensing layers is addressed. In this review, some other recent reviews related to the development of sensors based on titanium oxides are overviewed. Some designs of titanium-based nanomaterials used for the development of sensors are outlined.

Tunable TiO2-BN-Pd nanofibers by combining electrospinning and atomic layer deposition to enhance photodegradation of acetaminophen

The demand for fresh and clean water sources is increasing globally, and there is a need to develop novel routes to eliminate micropollutants and other harmful species from water. Photocatalysis is a promising alternative green technology that has shown great performance in the degradation of persistent pollutants. Titanium dioxide is the most used catalyst owing to its attractive physico-chemical properties, but this semiconductor presents limitations in the photocatalysis process due to the high band gap and the fast recombination of the photogenerated carriers. Herein, a novel photocatalyst has been developed, based on titanium dioxide nanofibers (TiO2 NFs) synthesized by electrospinning. The TiO2 NFs were coated by atomic layer deposition (ALD) to grow boron nitride (BN) and palladium (Pd) on their surface. The UV-Vis spectroscopy measurements confirmed the increase of the band gap and the extension of the spectral response to the visible range. The obtained TiO2/BN/Pd nanofibers were then tested for photocatalysis, and showed a drastic increase of acetaminophen (ACT) degradation (>90%), compared to only 20% degradation obtained with pure TiO2 after 4 h of visible light irradiation. The high photocatalytic activity was attributed to the good dispersion of Pd NPs on TiO2-BN nanofibers, leading to a higher transfer of photoexcited hole carriers and a decrease of photogenerated electron-charge recombination. To confirm its reusability, recycling tests on the hybrid photocatalyst TiO2/BN/Pd have been performed, showing a good stability over 5 cycles under UV and visible light. In addition, toxicity tests as well as quenching tests were carried out to check the toxicity of the byproducts formed and to determine active species responsible for the degradation. The results presented in this work demonstrate the potential of TiO2/BN/Pd nanomaterials, and open new prospects for the preparation of tunable photocatalysts.

Capacitive and Conductometric Type Dual-Mode Relative Humidity Sensor Based on 5,10,15,20-tetra Phenyl Porphyrinato Nickel (II) (TPPNi)

(1) Background: A quest for a highly sensitive and reliable humidity monitoring system for a diverse variety of applications is quite vital. Specifically, the ever-increasing demand of humidity sensors in applications ranging from agriculture to healthcare equipment (to cater the current demand of COVID-19 ventilation systems), calls for a selection of suitable humidity sensing material. (2) Methods: In the present study, the TPPNi macromolecule has been synthesized by using a microwave-assisted synthesis process. The layer structure of the fabricated humidity sensor (Al/TPPNi/Al) consists of pair of planar 120 nm thin aluminum (Al) electrodes (deposited by thermal evaporation) and ~160 nm facile spin-coated solution-processable organic TPPNi as an active layer between the ~40 µm electrode gap. (3) Results: Electrical properties (capacitance and impedance) of sensors were found to be substantially sensitive not only on relative humidity but also on the frequency of the input bias signal. The proposed sensor exhibits multimode (capacitive and conductometric) operation with significantly higher sensitivity ~146.17 pF/%RH at 500 Hz and 48.23 kΩ/%RH at 1 kHz. (4) Conclusions: The developed Al/TPPNi/Al surface type humidity sensor’s much-improved detecting properties along with reasonable dynamic range and response time suggest that it could be effective for continuous humidity monitoring in multi environmental applications.

Progress and Insights in the Application of MXenes as New 2D Nano-Materials Suitable for Biosensors and Biofuel Cell Design

Recent progress in the application of new 2D-materials-MXenes-in the design of biosensors, biofuel cells and bioelectronics is overviewed and some advances in this area are foreseen. Recent developments in the formation of a relatively new class of 2D metallically conducting MXenes opens a new avenue for the design of conducting composites with metallic conductivity and advanced sensing properties. Advantageous properties of MXenes suitable for biosensing applications are discussed. Frontiers and new insights in the area of application of MXenes in sensorics, biosensorics and in the design of some wearable electronic devices are outlined. Some disadvantages and challenges in the application of MXene based structures are critically discussed.

Insights in the Application of Stoichiometric and Non-Stoichiometric Titanium Oxides for the Design of Sensors for the Determination of Gases and VOCs (TiO2-x and TinO2n-1 vs. TiO2)

In this review article, attention is paid towards the formation of various nanostructured stoichiometric titanium dioxide (TiO2), non-stoichiometric titanium oxide (TiO2-x) and Magnéli phase (TinO2n-1)-based layers, which are suitable for the application in gas and volatile organic compound (VOC) sensors. Some aspects related to variation of sensitivity and selectivity of titanium oxide-based sensors are critically overviewed and discussed. The most promising titanium oxide-based hetero- and nano-structures are outlined. Recent research and many recently available reviews on TiO2-based sensors and some TiO2 synthesis methods are discussed. Some promising directions for the development of TiO2-based sensors, especially those that are capable to operate at relatively low temperatures, are outlined. The applicability of non-stoichiometric titanium oxides in the development of gas and VOC sensors is foreseen and transitions between various titanium oxide states are discussed. The presence of non-stoichiometric titanium oxide and Magnéli phase (TinO2n-1)-based layers in 'self-heating' sensors is predicted, and the advantages and limitations of 'self-heating' gas and VOC sensors, based on TiO2 and TiO2-x/TiO2 heterostructures, are discussed.

Utilization of Nano-TiO2 as an Influential Additive for Complementing Separation Performance of a Hybrid PVDF-PVP Hollow Fiber: Boron Removal from Leachate

The continuous increase in anthropogenic activities resulting in an increase in boron concentration in the environment is becoming a serious threat to public health and the ecosystem. In this regard, a hybrid polyvinylidene fluoride (PVDF)-polyvinyl pyrrolidone (PVP) hollow fiber was synthesized with hydrophilic nano-titanium oxide (TiO₂) at varied loadings of 0, 0.5, 1.0, 1.5, and 2.0 wt% using the phase inversion technique. The resultant membranes were characterized in terms of Scanning Electron Microscopy (SEM), Energy Dispersive X-ray Spectroscopy (EDX), contact angle, porosity, and zeta potential. The permeability flux was assessed using both pure water and leachate; also, rejection performance was evaluated based on boron removal from the leachate. The results revealed that the membrane with 1.0 wt% loading had the highest flux alongside an upturn in boron rejection percentage of 223 L/m²·h and 94.39%, respectively. In addition, the lowest contact angle of 50.01° was recorded with 1.0 wt% TiO₂ loading, and this implies that it is the most hydrophilic. Throughout the experiment cycles, the fiber with 1.0 wt% TiO₂ loading demonstrated a high flux recovery varying between 92.82% and 76.26% after 9 h filtration time. The physicochemical analysis of the permeate revealed that the boron concentration was significantly reduced to 0.43 mg/L, which is far lower than the discharge limit of 1.0 mg/L.

Development of a Fluorine-Free Polymer-Assisted-Deposition Route for YBa2Cu3O7−x Superconducting Films

Polymer assisted deposition (PAD) was used as an environmentally friendly, non-fluorine, growth method for superconducting YBa2Cu3O7−x (YBCO) films. The kinetics of the thermal decomposition of the precursor powder was studied by thermogravimetry coupled with mass spectrometry (TG-QMS). YBCO films were spin coated on (100) SrTiO3 (STO) single crystalline substrates, followed by a single step thermal treatment under wet and dry O2 and O2/N2 mixture. The as-obtained films were epitaxially grown having a [001]YBCO||[001]STO out-of-plane epitaxial relationship and exhibited good superconducting properties with Tc (R = 0) > 88 K, transition widths, ΔT ≈ 2 K and critical current densities as high as 2.3 MA/cm2 at 77 K and self magnetic field.

Electrorheological Properties of Polydimethylsiloxane/TiO2-Based Composite Elastomers

Electrorheological elastomers based on polydimethylsiloxane filled with hydrated titanium dioxide with a particle size of 100-200 nm were obtained by polymerization of the elastomeric matrix, either in the presence, or in the absence, of an external electric field. The viscoelastic and dielectric properties of the obtained elastomers were compared. Analysis of the storage modulus and loss modulus of the filled elastomers made it possible to reveal the influence of the electric field on the Payne effect in electrorheological elastomers. The elastomer vulcanized in the electric field showed high values of electrorheological sensitivity, 250% for storage modulus and 1100% for loss modulus. It was shown, for the first time, that vulcanization of filled elastomers in the electric field leads to a significant decrease in the degree of crosslinking in the elastomer. This effect should be taken into account in the design of electroactive elastomeric materials.

1D Titanium Dioxide: Achievements in Chemical Sensing

For the last two decades, titanium dioxide (TiO₂) has received wide attention in several areas such as in medicine, sensor technology and solar cell industries. TiO₂-based gas sensors have attracted significant attention in past decades due to their excellent physical/chemical properties, low cost and high abundance on Earth. In recent years, more and more efforts have been invested for the further improvement in sensing properties of TiO₂ by implementing new strategies such as growth of TiO₂ in different morphologies. Indeed, in the last five to seven years, 1D nanostructures and heterostructures of TiO₂ have been synthesized using different growth techniques and integrated in chemical/gas sensing. Thus, in this review article, we briefly summarize the most important contributions by different researchers within the last five to seven years in fabrication of 1D nanostructures of TiO₂-based chemical/gas sensors and the different strategies applied for the improvements of their performances. Moreover, the crystal structure of TiO₂, different fabrication techniques used for the growth of TiO₂-based 1D nanostructures, their chemical sensing mechanism and sensing performances towards reducing and oxidizing gases have been discussed in detail.

Tuning the Photo-Luminescence Properties of WO3 Layers by the Adjustment of Layer Formation Conditions

In this research we have applied sol-gel synthesis for the deposition of tungsten (VI) oxide (WO3) layers using two different reductants (ethanol and propanol) and applying different dipping times. WO3 samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier Transform Infrared spectroscopy (FTIR), photoluminescence (PL) and time-resolved photoluminescence decay methods. Photoelectrochemical (PEC) behaviour of synthesized coatings was investigated using cyclic voltammetry in the dark and under illumination. Formation of different structures in differently prepared samples was revealed and significant differences in the PL spectra and PEC performance of the samples were observed. The results showed that reductant used in the synthesis and dipping time strongly influenced photo-electrochemical properties of the coatings. Correlation between the morphology, PL and PEC behaviour has been explained.

Properties of Thermally Evaporated Titanium Dioxide as an Electron-Selective Contact for Silicon Solar Cells

Recently, titanium oxide has been widely investigated as a carrier-selective contact material for silicon solar cells. Herein, titanium oxide films were fabricated via simple deposition methods involving thermal evaporation and oxidation. This study focuses on characterizing an electron-selective passivated contact layer with this oxidized method. Subsequently, the SiO2/TiO2 stack was examined using high-resolution transmission electron microscopy. The phase and chemical composition of the titanium oxide films were analyzed using X-ray diffraction and X-ray photoelectron spectroscopy, respectively. The passivation quality of each layer was confirmed by measuring the carrier lifetime using quasi-steady-state photoconductance, providing an implied open circuit voltage of 644 mV. UV–vis spectroscopy and UV photoelectron spectroscopy analyses demonstrated the band alignment and carrier selectivity of the TiO2 layers. Band offsets of ~0.33 and ~2.6 eV relative to the conduction and valence bands, respectively, were confirmed for titanium oxide and the silicon interface.