Effect of Reactive Black 5 azo dye on soil processes related to C and N cycling

A novel electrocatalyst from TOCN/CGG hydrogel-supported Fe-rich sludge and its performance in treating azo dyes-contaminated water

Monolithic electrocatalysts are desired for the electro-Fenton oxidation system. We used a hydrogel consisting of TEMPO-oxidized cellulose nanofibers (TOCN) and cationic guar gum (CGG) to disperse and support Fe-rich sludge and finally obtained a Fe-doped biochar (denoted as C-Sludge@TOCN/CGG) after the freeze-drying and carbonization. This C-Sludge@TOCN/CGG exhibited a porous structure with evenly-distributed Fe due to the inherently three-dimensional porous structure of TOCN/CGG hydrogel and the abundant carbon content. Importantly, Fe and FeO existed in C-Sludge@TOCN/CGG due to the presence of TOCN and CGG during the pyrolysis. The electrochemical properties of C-Sludge@TOCN/CGG demonstrated its good electrocatalytic activity and stability with few side reactions. It had good performance in the electrocatalytic degradation of various azo dyes, attributed to the synergistic integration of TOCN/CGG-derived carbon matrix and carbonized Fe-rich sludge particles. Specifically, two transient radicals (i.e. ·OH and ·O2-) primarily improved the electrocatalytic degradation performance of C-Sludge@TOCN/CGG. This C-Sludge@TOCN/CGG also efficiently degraded a papermill-sourced wastewater containing direct red 23, direct yellow 11, direct black 19 and toner, in which the COD value decreased from 365.12 to 179.13 mg/L within 9 h. This work provides an example of utilizing renewable materials and solid waste to design electrocatalysts to address the wastewater issue.

Sulfonated Pentablock Copolymer (NexarTM) for Water Remediation and Other Applications

This review focuses on the use of a sulfonated pentablock copolymer commercialized as NexarTM in water purification applications. The properties and the use of sulfonated copolymers, in general, and of NexarTM, in particular, are described within a brief reference focusing on the problem of different water contaminants, purification technologies, and the use of nanomaterials and nanocomposites for water treatment. In addition to desalination and pervaporation processes, adsorption and photocatalytic processes are also considered here. The reported results confirm the possibility of using NexarTM as a matrix for embedded nanoparticles, exploiting their performance in adsorption and photocatalytic processes and preventing their dispersion in the environment. Furthermore, the reported antimicrobial and antibiofouling properties of NexarTM make it a promising material for achieving active coatings that are able to enhance commercial filter lifetime and performance. The coated filters show selective and efficient removal of cationic contaminants in filtration processes, which is not observed with a bare commercial filter. The UV surface treatment and/or the addition of nanostructures such as graphene oxide (GO) flakes confer NexarTM with coating additional functionalities and activity. Finally, other application fields of this polymer are reported, i.e., energy and/or gas separation, suggesting its possible use as an efficient and economical alternative to the more well-known Nafion polymer.

Facile Synthesis of Band Gap-Tunable Kappa-Carrageenan-Mediated C,S-Doped TiO2 Nanoparticles for Enhanced Dye Degradation

Semiconducting nanoparticles (SNPs) have garnered significant attention for their role in photocatalysis technology, offering a cost-effective and highly efficient method for breaking down organic dyes. Of particular significance within SNP-based photocatalysis are tunable band gap TiO2 nanoparticles (NPs), which demonstrate remarkable enhancement in photocatalytic efficiency. In the present work, we introduce an approach for the synthesis of TiO2 NPs using kappa-carrageenan (κ-carrageenan), not just as a reducing and stabilizing agent but as a dopant for the resulting TiO2 NPs. During the synthesis of TiO2 NPs in the presence of sulfate-rich carrageenan, the process predominantly leaves residual sulfur and carbon. The presence of residual carbon, in conjunction with sulfur doping, as indicated by fast FTIR spectra, XPS, and EDX, leads to a significant reduction in the band gap of the resulting composite to 2.71 eV. The reduction of composite band gap yields remarkable degradation of methylene blue (99.97%) and methyl orange (97.84%). This work presents an eco-friendly and highly effective solution for the swift removal of environmentally harmful organic dyes.

Adsorption of Methyl Red and Methylene Blue on Carbon Bioadsorbents Obtained from Biogas Plant Waste Materials

In this study, biocarbon was obtained from the waste material corn digest. Carbon adsorbents were obtained by physical activation of the precursor with CO2. Detailed physicochemical characterization of the biocarbon was carried out using low-temperature nitrogen adsorption/desorption, Boehm titration, zero-charge point (pHpzc) and iodine number. In addition, the sorption capacity of the biocarbon agents towards an aqueous solution of methylene blue and methyl red was determined, and the kinetics of the adsorption process were determined. The biocarbon adsorbents were characterized by an average developed specific surface area covering the range from 320 to 616 m2/g. The sorption capacity of the biocarbon adsorbents against methylene blue ranged from 40 mg/g to 146 mg/g, and for methyl red it covered the range from 31 mg/g to 113 mg/g. It was shown that the efficiency of organic dye removal by the obtained biocarbons depends on the initial concentration of the adsorbate solution, its mass, shaking rate, adsorbent-adsorbate contact time and temperature. The results obtained from the Langmuir and Freundlich kinetic models showed that the Langmuir model is the most suitable model for describing the adsorption of the studied pollutants on biocarbon. In turn, the adsorption kinetics of dyes is described according to the pseudo-second-order model. Adsorption studies also showed that as the process temperature increases, the removal efficiency of methylene blue and methyl red increases.

Next-Generation Water Treatment: Exploring the Potential of Biopolymer-Based Nanocomposites in Adsorption and Membrane Filtration

This review article focuses on the potential of biopolymer-based nanocomposites incorporating nanoparticles, graphene oxide (GO), carbon nanotubes (CNTs), and nanoclays in adsorption and membrane filtration processes for water treatment. The aim is to explore the effectiveness of these innovative materials in addressing water scarcity and contamination issues. The review highlights the exceptional adsorption capacities and improved membrane performance offered by chitosan, GO, and CNTs, which make them effective in removing heavy metals, organic pollutants, and emerging contaminants from water. It also emphasizes the high surface area and ion exchange capacity of nanoclays, enabling the removal of heavy metals, organic contaminants, and dyes. Integrating magnetic (Fe2O4) adsorbents and membrane filtration technologies is highlighted to enhance adsorption and separation efficiency. The limitations and challenges associated are also discussed. The review concludes by emphasizing the importance of collaboration with industry stakeholders in advancing biopolymer-based nanocomposites for sustainable and comprehensive water treatment solutions.

Encapsulation of Pseudomonas aeruginosa strain KBN12 decolourizes and bioremediates brilliant blue dye mediated toxicity in mung bean (Vigna radiata L.)

AIM

The aim of this study was to explore the decolourization and bioremediation ability of non-encapsulated and encapsulated Pseudomonas aeruginosa (strain KBN 12) against the azo dye brilliant blue (BB).

METHODS AND RESULTS

Six efficient BB dye-decolourizing bacteria were isolated from textile dye effluent. The most efficient free cells of P. aeruginosa KBN 12 along with the optimized conditions such as carbon source (maltose: 5 g L-1), and nitrogen source (ammonium chloride: 4 g L-1) at pH 6 at 37°C decolourized 72.69% of BB dye aerobically after 9 days of incubation under static conditions. Encapsulated (calcium alginate) P. aeruginosa KBN 12 decolourized 87.67% of BB dye aerobically after 9 days of incubation under the same optimized conditions. Fourier-transform infrared spectroscopy (FTIR) and gas chromatography (GC) analysis of the chemical structure of BB dye after decolourization found changes in functional and chemical groups. Phytotoxicity and soil respiration enzyme assays revealed that the decolourized dye or dye products were less toxic than the pure BB dye.

CONCLUSION

The encapsulation of P. aeruginosa KBN 12 proved to be an effective method for BB dye decolourization or remediation.

Designing Highly Active S-g-C3N4/Te@NiS Ternary Nanocomposites for Antimicrobial Performance, Degradation of Organic Pollutants, and Their Kinetic Study

The current research is about the synthesis of pure nickel sulfide, a series of Te (0, 0.5, 1, 1.5, 2, and 3 wt.%)-doped NiS (Te@NiS) nanoparticles (NPs), and a series of S-g-C3N4 (10, 30, 50, 70, and 80 wt.%)/Te@NiS nanocomposites (NCs), fabricated through a hydrothermal route. XRD and FTIR spectroscopic techniques demonstrated the successful synthesis of NPs and NCs. SEM-EDX images confirmed the flakelike structure and elemental constituents of the fabricated materials. Tauc plots were drawn, to calculate the band gaps of the synthesized samples. Te doping resulted in a significant reduction in the band gap of the NiS NPs. The photocatalytic efficiency of the NPs and NCs was investigated against MB, under sunlight. The results obtained for the photocatalytic activity, showed that 1%Te@NiS nanoparticles have an excellent dye degradation capacity in sunlight. This was made even better by making a series of SGCN/1% Te@NiS nanocomposites with different amounts of S-g-C3N4. When compared to NiS, Te@NiS, SGCN, and 70%SGCN/1%Te@NiS, the 70%SGCN/1%Te@NiS NCs have excellent antifungal ability. The higher impact of SGCN/Te@NiS, may be due to its enhanced ability to disperse and interact with the membranes and intracellular proteins of fungi. The 70%SGCN/1%Te@NiS NCs showed excellent antibacterial and photocatalytic efficiency. Thus, the 70%SGCN/1%Te@NiS NCs might prove fruitful in antibacterial and photocatalytic applications.

A comprehensive review on the metal-based green valorized nanocomposite for the remediation of emerging colored organic waste

In today's era, "green" synthesis is an emerging research trend. It has gained widespread attention owing to its dynamic behavior, reliability, simplicity, sustainability, and environment friendly approach for fabricating various nanomaterials. Green fabrication of metal/metal oxides nanomaterials, hybrid materials, and other metal-based nanocomposite can be utilized to remove toxic colored aqueous pollutants. Nanomaterials synthesized by using green approach is considered to be the significant tool to minimize unwanted or harmful by-products otherwise released from traditional synthesis methods. Various kinds of biosynthesized nanomaterials, such as animal waste and plant-based, have been successfully applied and well documented in the literature. However, their application part, especially for the cure of colored organic polluted water, has not been reported as a single review article. Therefore, the current work aims to assemble reports on using novel biosynthesized green metal-based nanomaterials to exclude harmful dyes from polluted water.

Bioremediation of reactive orange 16 by industrial effluent-adapted bacterial consortium VITPBC6: process optimization using response surface methodology (RSM), enzyme kinetics, pathway elucidation, and detoxification

Textile effluent is one of the most hazardous industrial pollutant sources. It is generated in huge volumes and contains a wide array of toxicants. Reactive azo dyes, which are xenobiotic compounds, are predominantly utilized by textile industries for dyeing cotton, viscose, wool, and silk. The conventional physicochemical treatments used by industrial effluent treatment plants are ineffective in dye degradation. The present study thus attempted to find a potential treatment for reactive azo dyes. A novel bacterial consortium VITPBC6 was constructed with the most potent and compatible reactive orange 16 (RO-16) decolorizing isolates of tannery and textile effluents, and the isolates were identified as Bacillus flexus VITSP6, Bacillus paraflexus VITSPB7, Bacillus megaterium VITSPB9, Bacillus firmus VITEPB1, B. flexus VITEPB2, and Bacillus aryabhattai VITEPB3. The physicochemical factors of RO-16 decolorization were optimized by response surface methodology. Consortium VITPBC6 was able to tolerate a high concentration of RO-16 up to 800 mg L^-1. A cocktail of enzymes including azoreductase, tyrosinase, laccase, lignin peroxidase, and manganese peroxidase was involved in RO-16 degradation by VITPBC6. Consortium VITPBC6 degraded RO-16 following zero-order reaction. The enzymes of consortium VITPBC6 had a V_max of 352 mg L^-1 day^-1 for RO-16 degradation; however, the K_m value was high. VITPBC6 biodegraded RO-16 resulting in the formation of small aromatic compounds. Lastly, different toxicity assays conducted with untreated RO-16 and its corresponding biodegraded metabolite revealed that the toxicity of biodegraded metabolites was significantly lower than the untreated dye.

Photocatalysis and adsorption kinetics of azo dyes by nanoparticles of nickel oxide and copper oxide and their nanocomposite in an aqueous medium

Background

Azo dyes are recalcitrant organic pollutants present in textile industry effluents. Conventional treatment methods to remove them come with a range of disadvantages. Nanoparticles and their nanocomposites offer more efficient, less expensive and easy to handle wastewater treatment alternative.

Methods

In this study, nanoparticles of nickel oxide (NiO-NPs), copper oxide (CuO-NPs) and their nanocomposite (NiO/CuO-NC) were synthesized using co-precipitation method. The functional groups present on the surface of synthesized nanomaterials were verified using Fourier-transform infrared spectroscopy (FTIR). Surface morphology was assessed using scanning electron microscopy (SEM) whereas purity, shape and size of the crystallite were determined using X-ray diffraction (XRD) technique. The potential of these nanomaterials to degrade three dyes i.e., Reactive Red-2 (RR-2), Reactive Black-5 (RB-5) and Orange II sodium salt (OII) azo dyes, was determined in an aqueous medium under visible light (photocatalysis). The photodegradation effectiveness of all nanomaterials was evaluated under different factors like nanomaterial dose (0.02-0.1 g 10 mL^-1), concentration of dyes (20-100 mg L^-1), and irradiation time (60-120 min). They were also assessed for their potential to adsorb RR-2 and OII dyes.

Results

Results revealed that at optimum concentration (60 mgL^-1) of RR-2, RB-5, and OII dyes, NiO-NPs degraded 90, 82 and 83%, CuO-NPs degraded 49, 34, and 44%, whereas the nanocomposite NiO/CuO-NC degraded 92, 93, and 96% of the said dyes respectively. The nanomaterials were categorized as the efficient degraders of the dyes in the order: NiO/CuO-NC > NiO-NPs > CuO-NPs. The highest degradation potential shown by the nanocomposite was attributed to its large surface area, small particles size, and quick reactions which were proved by advance analytical techniques. The equilibrium and kinetic adsorption of RR-2 and OII on NiO-NPs, CuO-NPs, and NiO/CuO-NC were well explained with Langmuir and Pseudo second order model, respectively (R² ≥ 0.96). The maximum RR-2 adsorption (103 mg/g) was obtained with NiO/CuO-NC. It is concluded that nanocomposites are more efficient and promising for the dyes degradation from industrial wastewater as compared with dyes adsorption onto individual NPs. Thus, the nanocomposite NiO/CuO-NC can be an excellent candidate for photodegradation as well as the adsorption of the dyes in aqueous media.

Integration of Mn-ZnFe2O4 with S-g-C3N4 for Boosting Spatial Charge Generation and Separation as an Efficient Photocatalyst

The disposal of dyes and organic matter into water bodies has become a significant source of pollution, posing health risks to humans worldwide. With rising water demands and dwindling supplies, these harmful compounds must be isolated from wastewater and kept out of the aquatic environment. In the research presented here, hydrothermal synthesis of manganese-doped zinc ferrites’ (Mn-ZnFe₂O₄) nanoparticles (NPs) and their nanocomposites (NCs) with sulfur-doped graphitic carbon nitride (Mn-ZnFe₂O₄/S-g-C₃N₄) are described. The samples’ morphological, structural, and bonding features were investigated using SEM, XRD, and FTIR techniques. A two-phase photocatalytic degradation study of (0.5, 1, 3, 5, 7, 9, and 11 wt.%) Mn-doped ZnFe₂O₄ NPs and Mn-ZnFe₂O₄/(10, 30, 50, 60, and 70 wt.%) S-g-C₃N₄ NCs against MB was carried out to find the photocatalyst with maximum efficiency. The 9% Mn-ZnFe₂O₄ NPs and Mn-ZnFe₂O₄/50% S-g-C₃N₄ NCs exhibited the best photocatalyst efficiency in phase one and phased two, respectively. The enhanced photocatalytic activity of the Mn-ZnFe₂O₄/50% S-g-C₃N₄ NCs could be attributed to synergistic interactions at the Mn-ZnFe₂O₄/50% S-g-C₃N₄ NCs interface that resulted in a more effective transfer and separation of photo-induced charges. Therefore, it is efficient, affordable, and ecologically secure to modify ZnFe₂O₄ by doping with Mn and homogenizing with S-g-C₃N₄. As a result, our current research suggests that the synthetic ternary hybrid Mn-ZnFe₂O₄/50% S-g-C₃N₄ NCs may be an effective photocatalytic system for degrading organic pollutants from wastewater.

Toxicity effect of the edible pigment carmoisine on Polyrhachis vicina Roger (Hymenoptera: Formicidae)

Carmoisine belongs to a water-soluble synthetic dye and is often used as a food additive. Previous research has shown that carmoisine is toxic to rats and zebrafish, but there have been few reports on the effect of carmoisine on soil-dwelling social insects. The present study evaluated carmoisine toxicity in Polyrhachis vicina Roger. We found that the effects of different concentrations of carmoisine on the mortality of workers were dose-dependent. The 10% lethal dose (LD₁₀), 50% lethal dose (LD₅₀) and 90% lethal dose (LD₉₀) of carmoisine to workers at 96 h was calculated to be 0.504, 5.491 and 10.478 g/L, respectivily. LD₁₀ of workers were selected to treat the fourth instar larvae, pupae and adults for 10 days. The results showed that the survival rate of all ants, except for females, was significantly reduced, especially larvae and workers. The body weight of larvae, pupae and males decreased significantly, while weight gain was observed in the females and workers. The appearance of larvae, pupae and workers changed after carmoisine treatment, such as body darkening and epidermis shrinking of larvae and pupae, as well as body segment expansion of workers. Furthermore, carmoisine altered the expression of the estrogen-related receptor, tailless and homothorax of P. vicina (Pv-ERR, Pv-tll and Pv-hth) to varying degrees in larvae and adults. We believe that variations in body weight can lead to a decrease in survival rate and appearance changes in the ants, which may be related to abnormal gene expressions caused by carmoisine treatment. Therefore, we confirm that carmoisine has negative effects on the growth and development of P. vicina.

Nanoscale zerovalent copper (nZVC) catalyzed environmental remediation of organic and inorganic contaminants: A review

Over the past decade, the nano zerovalent copper has emerged as an effective nano-catalyst for the environment remediation processes due to its ease of synthesis, low cost, controllable particle size and high reactivity despite its release during the remediation process and related concentration dependent toxicities. However, the improvised techniques involving the use of supports or immobilizer for the synthesis of Cu⁰ has significantly increased its stability and motivated the researchers to explore the applicability of Cu⁰ for the environment remediation processes, which is evident from access to numerous reports on nano zerovalent copper mediated remediation of contaminants. Initially, this review allows the understanding of the various resources used to synthesize zerovalent copper nanomaterial and the structure of Cu⁰ nanoparticles, followed by focus on the reaction mechanism and the species involved in the contaminant remediation process. The studies comprehensively presented the application of nano zerovalent copper for remediation of organic/inorganic contaminants in combination with various oxidizing and reducing agents under oxic and anoxic conditions. Further, it was evaluated that the immobilizers or support combined with various irradiation sources originates a synergistic effect and have a significant effect on the stability and the redox properties of nZVC in the remediation process. Therefore, the review proposed that the future scope of research should include rigorous focus on deriving an exact mechanism for synergistic effect for the removal of contaminants by supported nZVC.

Removal of Reactive Black 5 Dye by Banana Peel Biochar and Evaluation of Its Phytotoxicity on Tomato

Removal of Reactive Black 5 (RB5) dye from an aqueous solution was studied by its adsorption on banana peel biochars (BPBs). The factors affecting RB5 dye adsorption such as pH, exposure time, RB5 dye concentration, adsorbent dose, particle size and temperature were investigated. Maximum 97% RB5 dye removal was obtained at pH 3 with 75 mg/L adsorbate concentration by banana peel biochars. Fourier transform infrared (FTIR) and scanning electron microscopy (SEM) were used to characterize the adsorbent material. The data of equilibrium were analyzed by Langmuir and Freundlich isotherm models. The experimental results were best reflected by Langmuir isotherm with maximum 7.58 mg/g adsorption capacity. Kinetic parameters were explored and pseudo-second order was found suitable which reflected that rate of adsorption was controlled by physisorption. Thermodynamic variables exhibited that the sorption process was feasible, spontaneous, and exothermic in nature. Banana peel biochar showed excellent regeneration efficiency up to five cycles of successive adsorption-desorption. Banana peel biochar maintained >38% sorption potential of RB5 dye even after five cycles of adsorption-desorption. The phytotoxic study exhibited the benign nature of BPB-treated RB5 dye on tomato seeds.

Transport Behavior of RB5 Dye in Alluvial Soil in the Northeast of Brazil

The textile industry generates a large volume of chemically diversified effluents containing, among other compounds, dyes. Untreated wastes are contaminants to surface water, soil, and groundwater. In this aspect, various studies have explored the issue of contamination of alluvial soils in the Alto Capibaribe region, northeast of Brazil, due to local textile activity. This region, inserted into the Brazilian semiarid region, suffers from water scarcity, and there is a need for rural communities to use alluvial formations for water supply. The simulation of solute transport is a fundamental tool for understanding the environmental performance and risks associated with contamination by textile dyes. Transport parameters that directly influence pollutant dynamics in sedimentary environments are characterized. This study evaluated the retention and mobility of the dye Remazol Black 5 (RB5) in two superficial layers of alluvial soil from Alto Capibaribe to obtain transport parameters. In the laboratory, tests of mobility in soil columns with RB5 dye (concentration of the 25 mg L−1) and KBr tracer (concentration of the 35.7 g L−1) solutions were conducted. The CDE and two-region models were used to model the KBr experimental transport data, and the two-site model was used to model the RB5 experimental transport data. Physical non-equilibrium was found in the soils for KBr transport, and the two-region model adequately modeled the experimental breakthrough curves (BTCs). For the transport of RB5, the results showed a chemical non-equilibrium, and the two-site model was adequate to model the experimental BTCs. The results indicate that the surface layer is most responsible for the retention of RB5, where the RB5 solution was less mobile than in the lower layer. Both layers showed low retention and high mobility for RB5, indicating that the RB5 dye in the region may contaminate groundwater.

Ligninolytic enzymes in Basidiomycetes and their application in xenobiotics degradation

Variety of microorganisms have already proven their capabilities for degradation of wide range of wastes with anthropogenic nature. These pollutants, both liquid and solids, also include so called xenobiotics like phenol and its derivatives, PAHs, dyes, pesticides, pharmaceuticals, etc. Xenobiotics as bisphenol A (BPA), chlorhexidine (CHX), octenidine (OCT), other disinfectants and antiseptics have high ecotoxicological impact. Moreover, they can also impair our quality of life and our health interfering different metabolic and hormone receptors pathways in human body. Chemical treatment of such wastes is not a viable option because of its poor socio-economics and environmental merits. Therefore, applying effective, ecofriendly and cheap treatment methods is of great importance. Basidiomycetes are extensively investigated for their abilities to degrade numerous pollutants and xenobiotics. Through their extracellular ligninolytic enzymes they are capable of reducing or completely removing wide range of hazardous compounds. These enzymes can be categorized in two groups: oxidases (laccase) and peroxidases (manganese peroxidase, lignin peroxidase, versatile peroxidase). Due to the broad substrate specificity of the secreted enzymes Basidiomycetes can be applied as a powerful tool for bioremediation of diverse xenobiotics and recalcitrant compounds.

TiO2/guar gum hydrogel composite for adsorption and photodegradation of methylene blue

The development of porous adsorbent materials from renewable resources for water and wastewater treatment has received considerable interest from academia and industry. This work aims to synthesize composite hydrogel from the combination of guar gum (a neutral galactomannan polysaccharide) and TiO₂. The TiO₂-embedded guar gum hydrogel (TiO₂@GGH) was utilized to remove methylene blue through adsorption and photodegradation. The presence of TiO₂ particles in the hydrogel matrix (TiO₂@GGH) was confirmed by scanning electron microscopy-energy dispersive X-ray and X-ray photoelectron spectroscopy analysis. The mercury intrusion and N₂ sorption isotherm indicate the macroporous structure of the TiO₂@GGH composite, showing the presence of pore sizes ~420 μm. The dye removal efficiency of the GGH and TiO₂@GGH was evaluated in batch mode at ambient temperature under varying pH. The effect of UV radiation on the dye removal efficiency was also assessed. The results demonstrated that the highest dye removal was recorded at pH 10, with the equilibrium condition achieved within 5 h. UV radiation was shown to enhance dye removal. The maximum adsorption capacity of TiO₂@GGH is 198.61 mg g^-1, while GGH sorbent is 188.53 mg g^-1. The results imply that UV radiation gives rise to the photodegradation effect.

Structural Characterization and Adsorption Properties of Dunino Raw Halloysite Mineral for Dye Removal from Water

In this work, raw halloysite mineral from Dunino (Poland) has been characterized and tested as an efficient and low-cost adsorbent for dye removal from water. The morphology and structure of this clay were characterized using scanning electron microscopy (SEM) and transmission electron microscopy (TEM) and the chemical composition was evaluated by means of X-ray fluorescence spectroscopy (XRF), energy dispersive X-ray spectroscopy (EDX), and electron energy loss spectroscopy (EELS). The results showed that it is made up of both platy and tubular structures, mainly composed of Si, Al, and O. Iron oxide particles covering the platy structures were also observed. The surface charge of halloysite was measured by z-potential measurements and by the evaluation of the point of zero charge. The clay was tested as an adsorbent for the removal of positively and negatively charged dye molecules, i.e., methylene blue (MB) and methyl orange (MO), both separately and in a mixed-dye solution. Halloysite showed the ability to efficiently and selectively remove MB molecules by adsorption, both in a single-dye solution and in a mixed one. The adsorption of positive dyes on the clay surface mainly occurred through ion exchange at negatively charged sites on its surface. The possibility of regenerating the clay for further dye removal processes is also shown.

Biodegradation and biodetoxification of batik dye wastewater by laccase from Trametes hirsuta EDN 082 immobilised on light expanded clay aggregate

The biodegradation and biodetoxification of batik industrial wastewater by laccase enzyme immobilised on light expanded clay aggregate (LECA) were investigated. Laccase from Trametes hirsuta EDN 082 was covalently immobilised by modifying the LECA surface using (3-aminopropyl)trimethoxysilane and glutaraldehyde. The enzymatic characterisation of LECA-laccase showed promising results with an enzyme loading of 6.67 U/g and an immobilisation yield of 66.7% at the initial laccase activity of 10 U/g LECA. LECA-laccase successfully degraded batik industrial wastewater containing indigosol dye up to 98.2%. In addition, the decolorisation extent was more than 95.4% after four cycles. The phytotoxicity assessment of Vigna radiata and the microbial toxicity of two pathogenic bacteria, Bacillus subtilis and Pseudomonas aeruginosa, showed biodetoxification of treated batik dye wastewater. The characterisation using 3D light microscopy, scanning electron microscopy and Fourier transform infrared for LECA-laccase confirmed that laccase was successfully immobilised on LECA, and the decolorisation achieved through the combination of adsorption and enzymatic degradation. This study offers an environmentally friendly, effective and affordable LECA-laccase as a method for batik dye wastewater treatment.

SUPPLEMENTARY INFORMATION

The online version contains supplementary material available at 10.1007/s13205-021-02806-8.

Toxicity of biogenic zinc oxide nanoparticles to soil organic matter cycling and their interaction with rice-straw derived biochar

Given the rapidly increasing use of metal oxide nanoparticles in agriculture as well as their inadvertent addition through sewage sludge application to soils, it is imperative to assess their possible toxic effects on soil functions that are vital for healthy crop production. In this regard, we designed a lab study to investigate the potential toxicity of one of the most produced nanoparticles, i.e. zinc oxide nanoparticles (nZnO), in a calcareous soil. Microcosms of 80 g of dry-equivalent fresh soils were incubated in mason jars for 64 days, after adding 100 or 1000 mg of biogenically produced nZnO kg^-1 soil. Moreover, we also added rice-straw derived biochar at 1 or 5% (w: w basis) hypothesizing that the biochar would alleviate nZnO-induced toxicity given that it has been shown to adsorb and detoxify heavy metals in soils. We found that the nZnO decreased microbial biomass carbon by 27.0 to 33.5% in 100 mg nZnO kg^-1 soil and by 39.0 to 43.3% in 1000 mg nZnO kg^-1 soil treatments across biochar treatments in the short term i.e. 24 days after incubation. However, this decrease disappeared after 64 days of incubation and the microbial biomass in nZnO amended soils were similar to that in control soils. This shows that the toxicity of nZnO in the studied soil was ephemeral and transient which was overcome by the soil itself in a couple of months. This is also supported by the fact that the nZnO induced higher cumulative C mineralization (i.e. soil respiration) at both rates of addition. The treatment 100 mg nZnO kg^-1 soil induced 166 to 207%, while 1000 mg nZnO kg^-1 soil induced 136 to 171% higher cumulative C mineralization across biochar treatments by the end of the experiment. However, contrary to our hypothesis increasing the nZnO addition from 100 to 1000 mg nZnO kg^-1 soil did not cause additional decrease in microbial biomass nor induced higher C mineralization. Moreover, the biochar did not alleviate even the ephemeral toxicity that was observed after 24d of incubation. Based on overall results, we conclude that the studied soil can function without impairment even at 1000 mg kg^-1 concentration of nZnO in it.

Long-Term Exposure to Azo Dyes from Textile Wastewater Causes the Abundance of Saccharibacteria Population

Discharge of untreated wastewater is one of the major problems in various countries. The use of azo dyes in textile industries are one of the key xenobiotic compounds which effect both soil and water ecosystems and result in drastic effect on the microbial communities. Orathupalayam dam, which is constructed over Noyyal river in Tamil Nadu, India has become a sink of wastewater from the nearby textile industries. The present study had aimed to characterize the bacterial diversity and community profiles of soil collected from the vicinity of the dam (DS) and allied agricultural field (ALS) nearby the catchment area. The soil dehydrogenase and cellulase activities were significantly lower in DS compared to ALS. Additionally, the long-term exposure to azo dye compounds resulted in higher relative abundance of Saccharibacteria (36.4%) which are important for degradation of azo dyes. On the other hand, the relative abundance of Proteobacteria (25.4%) were higher in ALS. Interestingly, the abundance of Saccharibacteria (15.2%) were also prominent in ALS suggesting that the azo compounds might have deposited in the agricultural field through irrigation. Hence, this study revealed the potential bacterial phyla which can be key drivers for designing viable technologies for degradation of xenobiotic dyes.

A critical review on advances in the practices and perspectives for the treatment of dye industry wastewater

Rapid industrialization has provided comforts to mankind but has also impacted the environment harmfully. There has been severe increase in the pollution due to several industries, in particular due to dye industry, which generate huge quantities of wastewater containing hazardous chemicals. Although tremendous developments have taken place for the treatment and management of such wastewater through chemical or biological processes, there is an emerging shift in the approach, with focus shifting on resource recovery from such wastewater and also their management in sustainable manner. This review article aims to present and discuss the most advanced and state-of-art technical and scientific developments about the treatment of dye industry wastewater, which include advanced oxidation process, membrane filtration technique, microbial technologies, bio-electrochemical degradation, photocatalytic degradation, etc. Among these technologies, microbial degradation seems highly promising for resource recovery and sustainability and has been discussed in detail as a promising approach. This paper also covers the challenges and future perspectives in this field.

Dye removal from water and wastewater by nanosized metal oxides - modified activated carbon: a review on recent researches

The conventional water and wastewater treatment methods are unable to provide up-to-data organized standards for drinking water and discharging effluents into natural ecosystems. Therefore, developing advanced and cost-effective methods to achieve published standards for water and wastewater and population needs are nowadays necessity. The important parts of this article are providing literature information about dyes and their effects on the environment and human health, adsorption properties and mechanism, adsorbent characteristics, and recent information on various aspects of modified activated carbons with nanosized metal oxides (AC- NMOs) in the removal of dyes. This review also summarized the effect of main environmental and operational parameters such as adsorbent dosage, pH, initial dye concentration, contact time, and temperature on the dye adsorption using AC-NMOs. Furthermore, the applied isotherm and kinetic models have been discussed.

Toxic effects of Red-S3B dye on soil microbial activities, wheat yield, and their alleviation by pressmud application

This study examined the effect of Red-S3B textile dye on soil microbial activities, uptake of the dye by wheat plants and growth on the dye-contaminated soil. Moreover, pressmud (PM) application was investigated for its alleviative effect on wheat yield and dye uptake by plants. Preliminarily, soil was spiked with a wide concentration range (0, 100, 250, 500, 750 and 1000 mg kg^-1 soil) of Red-S3B dye and wheat was grown for 42-days. The dye did not suppress the activities of soil enzymes and growth of wheat seedlings at 100 mg kg^-1; however, beyond this level the dye had a linear negative effect on these attributes. With 1000 mg dye kg^-1 soil, wheat seedling biomass, viable microbial count, soil respiration, dehydrogenase, phosphatase, and urease activities decreased by 84%, 33%, 45%, 69%, 24%, and 11%, respectively as compared to uncontaminated soil. Moreover, phosphorus and potassium content in wheat shoot decreased, while the nitrogen content increased in Red-S3B contaminated soil. In the subsequent pot experiment, PM application (12.5 g kg^-1 soil) was assessed to alleviate the adverse effect of moderately toxic level of Red-S3B dye (500 mg kg^-1 soil) on wheat growth and yield. Root and straw biomass, and grain yield of wheat decreased by 13, 19 and 12%, respectively in Red-S3B contaminated soil as compared to uncontaminated soil. However, PM application to dye-contaminated soil retrieved the dye-induced reduction in root and straw biomass and grain yield to become statistically (p ≤ 0.05) at par with control plants. The color of Red-S3B was clearly visible in spikes depicting that plants absorbed Red-S3B but probably could not metabolize it. Amending the dye-contaminated soil with PM decreased Red-S3B content in awns from 78 to 37 mg kg^-1. Hence, it is concluded that Red-S3B textile dye is highly toxic to soil microbes and wheat plants at levels exceeding 100 mg kg^-1 soil. Soil application of PM alleviates the adverse effect of Red-S3B dye on wheat growth through reducing its uptake by plants.

Augmented Biodegradation of Textile Azo Dye Effluents by Plant Endophytes: A Sustainable, Eco-Friendly Alternative

Textile industry consumes a large proportion of available water and releases huge amounts of toxic azo dye effluents, leading to an inevitable situation of acute environmental pollution that has been a significant threat to mankind. Decolorization or detoxification of harmful azo dyes has become a global priority to overcome the disastrous consequences and salvage the ecosystem. Biodegradation of textile azo dyes by endophytes stands to be a lucrative and viable alternative over conventional physico-chemical methods, owing to their eco-friendliness, cost-competitive and non-toxic nature. Especially, plant endophytic microbes exhibit promising biodegradation potential which has wired up the effective removal of textile azo dyes, attributing to their ability to produce dye degrading enzymes, laccases, peroxidases and azoreductases. Although both bacterial and fungal endophytes have been tried for azo dye degradation, endophytic fungi find broader application over bacteria. Despite of the advancements made in microbe-mediated biodegradation, there is still a need to fill the gap in lab to in situ translation of biodegradation research. This review concisely accentuates the xenobiotics of textile azo dyes and microbial mechanisms of biodegradation of textile azo dyes, positing plant endophytic community, especially bacterial and fungal endophytes as the potential dye degraders, highlighting currently reported dye degrading endophytic species.

Eco-Efficient Green Seaweed Codium decorticatum Biosorbent for Textile Dyes: Characterization, Mechanism, Recyclability, and RSM Optimization

Biosorption using natural waste has emerged as a potential and promising strategy for removal of toxic dyes from wastewaters in comparison to conventional ones. Herein, the Codium decorticatum alga (CDA) was biologically identified and used as a biosorbent for anionic and cationic dyes from aqueous solutions. SEM analysis showed a rough surface with an irregular edge and shape while hydroxyl, amine, sulfur and carboxyl functional groups were identified using FTIR analysis. TGA/DTG confirmed the stability of CDA and the adsorption process. Batch studies were conducted to investigate the effect of operational factors such as initial pH, biosorbent dosage, temperature, initial concentration, and solid/liquid contact time on the biosorption of crystal violet (CV) and Congo red (CR) dyes. For both CV and CR dyes, the biosorption kinetics was accurately described by the pseudo-second-order model and the Langmuir isotherm was found to be best fitted for equilibrium data. Maximum uptake capacities have attained up to 278.46 mg/g for CV and 191.01 mg/g for CR. The CV and CR dye biosorption mechanism was ultimately manifested through the electrostatic interactions. The regeneration study showed that the CDA presents excellent reuse performance up to four consecutive cycles. The process optimization was performed using the response surface methodology based on Box-Behnken design (RSM-BDD). Accordingly, the optimum predicted removal efficiencies using RSM-BBD for CV and CR were obtained, respectively, at 96.9 and 89.8% using a CDA dose of 1.5 g/L, dye concentration of 20 mg/L, pH of 10 for CV, and pH of 4 for CR. Overall, CDA behaves as an efficient, recyclable, cheap, and eco-friendly adsorbent for cleaning-up of dyed effluents.

Myco-decontamination of azo dyes: nano-augmentation technologies

Effluents of textile, paper, and related industries contain significant amounts of synthetic dyes which has serious environmental and health implications. Remediation of dyes through physical and chemical techniques has specific limitations. Augmented biological decontamination strategies 'microbial remediation' may involve ring-opening of dye molecules besides the reduction of constituent metal ions. Both bacterial and fungal genera are known to exhibit metabolic versatility which can be harnessed for effective bio-removal of the toxic dye contaminants. Ascomycetous/basidiomycetes fungi can effectively decontaminate azo dyes through laccase/peroxidase enzyme-mediated catalysis. The extent, efficacy, and range of fungal dye decontamination can be enhanced by the conjugated application of nanomaterials, including nanoparticles (NPs) and their composites. Fungal cell-enabled NP synthesis- 'myco-farmed NPs', is a low-cost strategy for scaled-up fabrication of a variety of metal, metal oxide, non-metal oxide NPs through oxidation/reduction of dissolved ions/molecules by extracellular biomolecules. Augmented and rapid decontamination of azo dyes at high concentrations can be achieved by the use of myco-farmed NPs, NPs adsorbed fungal biomass, and nano-immobilized fungi-derived bio-catalytical agents. This manuscript will explore the opportunities and benefits of mycoremediation and application of fungus-NP bionanoconjugate to remediate dye pollutants in wastewaters and land contaminated with the effluent of textile industries.

Bacillus firmus strain FSS2C ameliorated oxidative stress in wheat plants induced by azo dye (reactive black-5)

This study was conducted to determine the ability of a bacterial strain FSS2C to ameliorate growth of wheat plants grown under induced stress of reactive black-5 (RB-5). The strain was taxonomically identified as Bacillus firmus on the basis of its 16S rRNA gene sequence analysis. The B. firmus FSS2C was found physiologically potent in phosphate solubilization, indole-3-acetic acid production and ammonia synthesis in the presence of varying concentrations of azo dye RB-5. Moreover, it decolorized RB-5 in vitro with the maximum decolorization (%) found at pH 7 and 30 °C. Inoculation of wheat plants, growing under stress induced by RB-5 dye, with rifampicin-resistant derivatives of the strain FSS2C substantially reduced the cellular oxidative stress, thereby resulting in higher plant biomass as compared to non-inoculated plants. Similarly, the inoculated plants revealed higher nutrient content in shoots as compared to non-inoculated ones. It was concluded that B. firmus strain FSS2C alleviated the oxidative stress impairment caused by reactive black-5 in wheat plants. Therefore, the strain can be used as bio-inoculant in wastewater irrigated soils.

Impact assessment of azulene and chromium on growth and metabolites of wheat and chilli cultivars under biosurfactant augmentation

Dye azulene and heavy metal chromium are two different types of persistent toxic compounds present in textile effluent. These compounds contaminate the soil and harm plant productivity during unchecked disposal of textile effluent to the farm soil. Environmental and safety concerns associated with crops, soil, and human health encourage the exploration of biological tools to control the issue. We hereby propose the application of biosurfactant (lipopeptide) to reduce the toxic effects of azulene and chromium in plants. Results of the study indicated that the augmentation of biosurfactant with azulene and chromium promoted seed germination, plant biomass, specific leaf weight (SLW), chlorophyll content, protein content, soluble sugar and ascorbic acid concentration in cultivars of wheat and chilli. Decreasing the level of proline under biosurfactant augmentation further confirms the reduction of oxidative stress caused by azulene and chromium amendment. The results indicated that lipopeptide biosurfactant could be an effective biological tool to reduce the toxic effect of persistent substances in soil, thus maintaining soil health and sustainable agriculture.