Accurate gamma-ray dose measurement up to 10 MeV by glass dosimeter with a sensitivity control filter for BNCT

Glass dosimeters are very useful and convenient detection elements in radiation dosimetry. In this study, this glass dosimeter was applied to a BNCT treatment field. Boron Neutron Capture Therapy (BNCT) is a next-generation radiation therapy that can selectively kill only cancer cells. In the BNCT treatment field, both neutrons and secondary gamma-rays are generated. In other words, it is a mixed radiation field of neutrons and gamma-rays. We thus proposed a novel method to measure only gamma-ray dose in the mixed field using two RPLGD (Radiophoto-luminescence Glass Dosimeter) and two sensitivity control filters in order to control the dose response of the filtered RPLGD to be proportional to the air kerma coefficients, even if the gamma-ray energy spectrum is unknown. As the filter material iron was selected, and it was finally confirmed that reproduction of the air kerma coefficients was excellent within an error of 5.3% in the entire energy range up to 10 MeV. In order to validate this method, irradiation experiments were carried out using standard gamma-ray sources. As the result, the measured doses were in acceptably good agreement with the theoretical calculation results by PHITS. In the irradiation experiment with a volume source in a nuclear fuel storage room, the measured dose rates showed larger compared with survey meter values. In conclusion, the results of the standard sources showed the feasibility of this method, however for the volume source the dependence of the gamma-ray incident angle on the dosimeter was found to be not neglected. In the next step, it will be necessary to design a thinner filter in order to suppress the effect of the incident angle.

An analysis of the effects of chronic low dose-rate radiation exposure on cancer focusing on the differences among cancer types

PURPOSE

The effect of chronic low dose-rate radiation exposure on cancers was investigated by analyzing the data of mice experiments conducted at the Institute for Environmental Sciences (IES). This analysis focuses on the differences between malignant lymphomas and solid cancers.

MATERIALS AND METHODS

The analysis is conducted based on the mathematical model introduced in our previous work. The model is expanded to analyze malignant lymphomas and solid cancers separately. Using the expanded model, the effect of chronic low dose-rate radiation on malignant lymphomas and solid cancers are discussed based on their occurrences, progressions, and mortalities.

RESULTS

Non-irradiated control group and 20 mGy/day × 400 days irradiated groups are analyzed. The analysis showed that radiation exposure shortened mean life expectancy for both malignant lymphomas and solid cancers (shorter by 89.6 days for malignant lymphomas and 149.3 days for solid cancers). For malignant lymphomas, both the occurrence and the progression are affected by radiation exposure. The mean age at which malignant lymphoma developed in mice was shortened by 32.7 days and the mean progression period was shortened by 57.3 days. The occurrence of solid cancer is also affected by radiation exposure, wherein the mean age at which solid cancer develops was shortened by 147.9 days. However, no significant change in progression period of solid cancers was seen in the analysis.

CONCLUSIONS

The analysis showed that the occurrence and mean lifespan are affected in both malignant lymphomas and solid cancers. The shortening of the progression period is only seen in malignant lymphoma, no significant change was observed in solid cancers.

A mathematical model for radiation-induced life-shortening attributed to cancer

PURPOSE

In this paper, we described our mathematical model for radiation-induced life shortening in detail and applied the model to the experimental data on mice to investigate the effect of radiation on cancer-related life-shortening.

MATERIALS AND METHODS

Our mathematical model incorporates the following components: (i) occurrence of cancer, (ii) progression of cancer over time, and (iii) death from cancer. We evaluated the progression of cancer over time by analyzing the cancer incidence data and cumulative mortalities data obtained from mice experiments conducted at the Institute for Environmental Sciences (IES).

RESULTS

We analyzed non-irradiated control and 20 mGy/day × 400 days irradiated groups. In the analysis, all malignant neoplasms were lumped together and referred to as 'cancer'. Our analysis showed that the reduction in lifespan (104 days in median) was the result of the early onset of cancer (68 days in median) and the shortening of the cancer progression period (48 days in median).

CONCLUSIONS

We described in detail our mathematical model for radiation-induced life-shortening attributed to cancer. We analyzed the mice data obtained from the experiment conducted at the IES using our model. We decomposed radiation-induced life-shortening into the early onset of cancer and the shortening of the cancer progression period.

Surface Properties of Resin Composites and CAD/CAM Blocks After Simulated Toothbrushing

OBJECTIVES

This study aimed to evaluate the surface gloss, surface roughness, and color change of restorative materials after a three-body wear abrasion.

METHODS AND MATERIALS

Four resin composites with different filler particle size (Gracefil Flo [GFF, 0.7 μm], Gracefil LoFlo [GFL, 0.25 μm], Gracefil ZeroFlo [GFZ, 0.15 μm], and Gracefil Putty [GFP, 0.3 μm]), two CAD/CAM resin composite blocks with different filler particle size (Cerasmart 300 [CS3, 0.7 μm] and Cerasmart Prime [CSP, 0.3 μm], GC), and one CAD/CAM lithium disilicate glass-ceramic block (Initial LiSi Block [ILS], GC) as a control were evaluated. Twenty slab-shaped specimens were obtained from each material. Ten specimens were subjected to 80,000 toothbrushing strokes and measured for surface gloss (Gloss Unit, GU), surface roughness (Ra, μm), and color (L*, a*, and b* values) before toothbrushing and at every 20,000 strokes. Color differences (ΔL*, Δa*, Δb*, and ΔE00) before and after toothbrushing were calculated. After 80,000 strokes, abraded surfaces were observed using scanning electron microscopy. The other 10 specimens were measured for Vickers microhardness (VHN).

RESULTS

After 80,000 toothbrushing strokes, the mean GU ranged from 60.43 to 16.12 (the highest for ILS and lowest for GFL), and the mean Ra ranged from 0.079 to 4.085 (the lowest for ILS and highest for GFL). At all measuring stages, the calculated ΔE00 values ranged from 0.31 to 0.92 for all materials. The mean VHN ranged from 632.34 to 39.08 (the highest for ILS and lowest for GFZ). The resin composite containing the largest filler particle (GFF) showed significantly lower Ra and higher VHN than other resin composites (GFL, GFZ, and GFP). The CAD/CAM resin composite block containing a smaller filler particle (CSP) retained significantly higher GU than that containing a larger filler particle (CS3). A negative correlation between GU and Ra was detected.

CONCLUSIONS

Based on the findings, toothbrush abrasion induced a decrease in GU and an increase in Ra for all resin-based materials tested. Resin-based materials with larger filler size tended to show lower Ra, while resin-based materials with smaller filler size tended to show a smaller reduction in GU. These were more pronounced for light-cure resin composites than for resin composite blocks for CAD/CAM.

Response control of RPLGD for gamma-ray dose measurement using lead filters for BNCT

Boron Neutron Capture Therapy (BNCT) is a cell-selective radiotherapy using a neutron capture reaction of ¹⁰B. In recent years, Accelerator Based Neutron Sources (ABNS) are under development instead of nuclear reactors for the next-generation neutron irradiation system for BNCT. However, ABNS as well as nuclear reactor usually generates unavoidable secondary gamma-rays by neutron-nuclear reactions such as capture reaction. In this research, we aimed to develop a separate measurement method of only gamma-rays in a mixed field of neutrons and gamma-rays using a fluorescent glass dosimeter (RPLGD), because most dosimeters have sensitivity to both radiation types. For this purpose, we proposed a lead filter method using two RPLGDs and lead filters. However, this method has a problem that the sensitivity to low energy gamma-rays (∼100 keV) is very small. In order to improve the sensitivity to low energy gamma-rays, we devised a method using a specially shaped lead filter. From theoretical calculations, we have shown that it was possible to estimate the air dose rate of the field where the gamma-ray energy spectrum shape was known for energies up to 10 MeV. In addition, we produced the specially shaped lead filter and experimentally confirmed the validity of the lead filter method using several gamma-ray standard sources and by measurements in a nuclear fuel storage room.

Ex vivo UV-vis and FTIR photoacoustic spectroscopy of natural nanoemulsions from cellulose nanocrystals and saponins topically applied into the skin: Diffusion rates and physicochemical evaluation

Nanoemulsions are increasingly gaining importance in the development of topically applied medicine and cosmetic products because their small droplets favor the penetration rates of active compounds into the body. In this scenario, the measurements of their diffusion rates as well as eventual physicochemical changes in the target tissues are of utmost importance. It is also recognized that the use of natural surfactants can avoid allergic reactions as frequently observed for synthetic products. The natural saponins extracted from Sapindus Saponaria have the property of forming foam and are exploited as biocompatible and biodegradable, while cellulose nanocrystals are known to increase the stability of a formulation avoiding the coalescence of drops at the interface. Therefore, nanoemulsions combining natural saponins and cellulose nanocrystals are promising systems that may facilitate greater diffusion rates of molecules into the skin, being candidates to substitute synthetic formulations. This study applied the Photoacoustic Spectroscopy technique to measure the diffusion rates and the physicochemical properties of nanoemulsified formulations containing saponins and cellulose nanocrystals topically applied to the skin. The ex vivo study combined the first-time photoacoustic measurements performed in both ultraviolet-visible and mid-infrared spectral regions. The toxicity of these formulations in L929 cells was also evaluated. The results showed that the formulations were able to propagate throughout the skin to a depth of approximately 756 μm, reaching the dermal side. The non-observation of absorbing band shifting or new bands in the FTIR spectra suggests that there were no structural changes in the skin as well as in the formulations after the nanoemulsions administration. The cytotoxicity results showed that the increase of cellulose nanocrystals concentration decreased cellular toxicity. In conclusion, the results demonstrated the advantage of combining photoacoustic methods in the ultraviolet-visible and mid-infrared spectral regions to analyze drug diffusion and interaction with the skin tissues. Both methods complement each other, allowing the confirmation of the nanoemulsion diffusion through the skin and also suggesting there were no detectable physicochemical changes in the tissues. Formulations stabilized with saponins and cellulose nanocrystals showed great potential for the development of topically administered cosmetics and drugs.

Cerebrospinal fluid-based boron delivery system may help increase the uptake boron for boron neutron capture therapy in veterinary medicine: A preliminary study with normal rat brain cells

Boron neutron capture therapy (BNCT) is a non-invasive type of radiation therapy developed for humans and translated to veterinary medicine. However, clinical trials on BNCT for patients with brain tumors are on-going. To improve the therapeutic efficacy of BNCT for brain tumors, we developed a boron delivery system that involves the cerebrospinal fluid (CSF), in contrast to the conventional method that involves intravenous (IV) administration. This study aimed to investigate the time-concentration profile of boron in the CSF as well as the uptake rate of boron by the brain cells after administering L-p‑boronophenylalanine (BPA) into the lateral ventricle of normal rats. Brain cell uptake rates were compared between the CSF-based and IV administration methods. The CSF-based and IV administration methods achieved comparable brain cell uptake levels; however, the former method involved lower BPA doses than the latter method. These findings suggest that the CSF method may reduce the economic and physical burdens associated with this treatment in brain tumor patients. Future studies should validate these findings in rat models of brain tumors.

COMBINED ANALYSIS OF CANCER INCIDENCE AND LIFESPAN IN MICE EXPOSED TO CHRONIC LOW DOSE RATE RADIATION

The authors performed a combined analysis using the data obtained from continuous low dose rate irradiation experiments on mice conducted at the Institute for Environmental Sciences, namely, cancer incidence data and lifespan data. They estimated the length of cancer progression period, which is difficult to assess experimentally. The combined analysis showed that the mean cancer progression period is 173 d in the control group and 103 d in the irradiated group.

Boron Delivery to Brain Cells via Cerebrospinal Fluid (CSF) Circulation for BNCT in a Rat Melanoma Model

Simple Summary

The blood–brain barrier (BBB) is formed by the brain capillary endothelium and prevents almost all therapeutic agents from reaching the brain. The importance of the BBB in brain tumor treatments has not been recognized until recently, including in the case of boron neutron capture therapy (BNCT), although it affects therapeutic efficacy when treating brain tumors. Recently, some drug delivery systems to bypass the BBB have been developed for brain tumor therapy, and our laboratory has been developing a system for boron delivery to brain cells using cerebrospinal fluid (CSF) circulation, which we call the “boron CSF administration method”. In this study, we carried out experiments with brain tumor model rats to demonstrate the usefulness of the CSF administration method for BNCT. As a result, we found that boron injected using the CSF administration method accumulates to high levels in tumor cells, with a high T/N ratio. In addition, the dose required for the boron drug was much lower than that used in the intravenous (IV) administration method for equivalent effects. This approach makes it possible for clinicians to inject a lower drug dose into patient, thus reducing the potential side effects of excessive amounts of the drug and decreasing its cost. We hope our findings will inspire additional studies on boron delivery to brain tumors for BNCT.

Abstract

Recently, exploitation of cerebrospinal fluid (CSF) circulation has become increasingly recognized as a feasible strategy to solve the challenges involved in drug delivery for treating brain tumors. Boron neutron capture therapy (BNCT) also faces challenges associated with the development of an efficient delivery system for boron, especially to brain tumors. Our laboratory has been developing a system for boron delivery to brain cells using CSF, which we call the “boron CSF administration method”. In our previous study, we found that boron was efficiently delivered to the brain cells of normal rats in the form of small amounts of L-p-boronophenylalanine (BPA) using the CSF administration method. In the study described here, we carried out experiments with brain tumor model rats to demonstrate the usefulness of the CSF administration method for BNCT. We first investigated the boron concentration of the brain cells every 60 min after BPA administration into the lateral ventricle of normal rats. Second, we measured and compared the boron concentration in the melanoma model rats after administering boron via either the CSF administration method or the intravenous (IV) administration method, with estimation of the T/N ratio. Our results revealed that boron injected by the CSF administration method was excreted quickly from normal cells, resulting in a high T/N ratio compared to that of IV administration. In addition, the CSF administration method resulted in high boron accumulation in tumor cells. In conclusion, we found that using our developed CSF administration method results in more selective delivery of boron to the brain tumor compared with the IV administration method.

Design of SPECT for BNCT to measure local boron dose with GAGG scintillator

Boron Neutron Capture Therapy (BNCT) is a promising cancer therapy, which has recently been in practical use in Japan especially using an accelerator. In BNCT real-time measurement of local boron dose is required. In the present study, a novel design of a SPECT system for BNCT (BNCT-SPECT) has been carried out to realize estimation of the local boron dose, i.e., treatment effect of BNCT. Necessary performance which BNCT community requires includes accuracy of 5% and spatial resolution of 5 mm, which are regarded to be difficult to realize. A possible design was investigated to meet the requirements. The design results we achieved are as follows: As for the elemental detection device, GAGG (3.5 × 3.5 × 30 mm³) was selected, and for the collimator, the collimator hole diameter was 3.5 mm, the collimator hole pitch was 4 mm and the collimator length was 26 cm. For the obtained performance with the design, the accuracy was 4.4% and the spatial resolution was 5.1 mm. Currently prior to production of the real system, a prototype of BNCT-SPECT is being developed to acquire real projection data to confirm the performance and examine our own image reconstruction method with the obtained projection data.

Does the phenotypic morphology of the human brachial plexus reflect the theoretical development of concomitant regulation in thoracolumbar spines and nerves?

BACKGROUND

Experimental evidence identified that thoracolumbar mutants caused by Hox genes 7-10 mutants also involve a craniocaudal shift and/or the addition or reduction of segments of the limb plexus roots. This study investigated whether the theoretical concomitant shift of the brachial plexus roots in human different thoracolumbar counts is shared as confirmed in those of the human lumbosacral plexus.

MATERIALS AND METHODS

The phenotypic morphology of the brachial plexus and its arterial interaction on 20 sides of 10 atypical human thoracolumbar counts out of the 354 sides of the 177 cadavers, were compared with those of 52 sides of 26 cases in a typical human vertebral formula (7C_12T_5L_5S).

RESULTS

Regardless of the course and branching patterns of the axillary artery, our results showed that the main brachial plexus roots were composed of only five segments of the 5th-9th spinal nerves, with small contributions from the 4th and/or 10th nerves. This root composition is identical to a typical human thoracolumbar formula, and therefore, neither a craniocaudal shift nor additional/reduced main roots occurred in our thoracolumbar variants.

CONCLUSIONS

Unlike the concomitant shift of the lumbosacral plexus roots, our present cases suggest that the phenotypic morphology of the human brachial plexus may be less likely to show theoretical craniocaudal shifts, further data on the root changes in different vertebral formulae are needed for its accurate validation.

Cloves (Syzygium aromaticum) fluid gel on healing of pododermatitis in rabbits

Wounds are damaging to quality life of confined animals, causing dysfunction in spinal, members injuries, and reduction in productive performance. This research investigated the clove antimicrobial and antioxidant activity on the healing of decubitus wounds (pododermatitis) of rabbits (Oryctolagus cuniculus). Adult animals were treated for 21 days every three days with a fluid gel spray in the wound region: control fluid gel without addition of clove (FGC0), fluid gel with addition of 1% clove powder (FGC1), and fluid gel with 2% clove powder (FGC2). Microbiological analysis for Escherichia coli and Pseudomonas spp. were performed during 21 days of experimental period. After this period, samples from treated skin were evaluated for histological analysis and evaluation of the healing process by spectroscopy (FTIR-ATR). Rabbits treated with FGC2 showed advanced healing and decreased tissue inflammation similar to healthy rabbits, while FGC0 rabbits showed a decrease in bacterial contamination without signs of healing. Both FGC1 and FGC2 rabbits demonstrated antimicrobial and antioxidant action against both bacteria tested, favoring the wound healing process. Considering the results, the use of fluid gel with 2% of clove powder (Syzigium aromaticum) based on the best antimicrobial, antioxidant and anti-inflammatory activities on healing of decubitus wounds (pododermatitis) of rabbits in commercial farming system.

In Vitro Evaluation of the Stabilization Time of Chemical Bonds During Setting Reaction and Microhardness of Preheated Glass-Ionomer Cements

OBJECTIVES

To evaluate the effect of preheating glass-ionomer cement (GIC) restorative materials on stabilization time (ST) of their metal carboxylate bonds and on microhardness.

METHODS AND MATERIALS

Two conventional highviscosity GICs, Ketac Universal (3M ESPE) and Equia Forte (GC), were evaluated. The thermographic camera was used to measure the temperature inside the glass-ionomer cement capsules before and after heating. The preheating of capsules was performed at 54°C for 30 seconds in a commercial device. Characterization of ST in the GICs was determined by Fourier Transform Infrared (FTIR) spectroscopy. For this, 10 samples of each material were prepared, five in the non-preheated group (control) and five with preheating. FTIR spectra were obtained 10 minutes after mixing (control group) or after heating and then every 10 minutes for 120 minutes. For the microhardness test, 20 cylindrical specimens (3 mm height × 6 mm diameter) were prepared for each material (10 preheated, 10 control). The microhardness was determined at three time intervals: 10 minutes after mixing, after the ST as detected through the FTIR part of the study, and after one week. Knoop microhardness was assessed using a diamond indenter with a 25 g load and 15 seconds dwell time.

RESULTS

Ketac Universal showed an increase in temperatures of 15.7°C for powder and 3.6°C for liquid, while Equia Forte showed 16.4°C for powder and 8.5°C for liquid. FTIR spectra indicated that preheating reduced the ST for Equia Forte but increased it for Ketac Universal. Preheating increased the initial microhardness (T1) of Equia Forte. With maturation over one week, it was observed that preheating significantly improved the microhardness of both materials compared with the control specimens.

CONCLUSION

Preheating influenced the ST and the microhardness of Ketac Universal and Equia Forte. The ST and microhardness of Ketac Universal increased after seven days, whereas Equia Forte showed a reduced ST and increased microhardness from the outset.

Cryptic species in a Vulnerable seabird: shorttailed albatross consists of two species

The occurrence of cryptic species within a threatened taxon is rare, but where they do occur, understanding species boundaries is essential for planning an effective conservation strategy. The short-tailed albatross Phoebastria albatrus is a Vulnerable seabird that mainly breeds on Torishima and the Senkaku Islands in the western North Pacific. Although it has been tacitly regarded as a single management unit with 2 breeding sites, the species is known to comprise 2 genetically separated populations (Senkaku-type and Torishima-type). However, morphological examination of birds from both populations has not been conducted owing to the difficulty in accessing the Senkaku Islands. In this study, we examined the morphological differences between immigrants from the Senkaku Islands to Torishima (Senkaku-type) and native birds on Torishima (Torishima-type) and found significant differences in morphological characteristics between the 2 bird types. In general, Torishima-type birds were larger than Senkaku-type birds, whereas Senkaku-type birds had relatively longer beaks. Based on the morphological differences found in this study as well as genetic and ecological differences revealed in previous studies, we believe that Senkaku- and Torishima-type birds should be classified as different cryptic species. To the best of our knowledge, this is the first case of cryptic species being identified in a threatened avian species.

Effects of Bioactive Agents on Dentin Mineralization Kinetics After Dentin Bleaching

Objectives:

This study evaluated effects of Bioglass 45S5 (BG) and Biosilicate (BS) remineralization on the chemical composition and bond strength of control dentin (CD) and bleached dentin (BD) surfaces.

Methods and Materials:

Dentin bleaching treatment was performed using the walking bleaching technique with 0.01 g of sodium perborate and 0.5 mL of 3% hydrogen peroxide for 14 days. Remineralization treatment was carried out by rubbing a remineralization solution (0.015 g of BG or BS diluted in 1.35 mL of distilled water) on the etched dentin surface for 30 seconds. Micro-Raman spectroscopy (MRS) was used to quantitatively analyze the mineral matrix ratios of CD and BD (n=5) after remineralization treatment with BG and BS over 15 days of incubation in artificial saliva. The CD and BD discs (n=10) with and without remineralization treatment with BG and BS were restored using a two-step etch-and-rinse adhesive system (Optibond S, Kerr) and five layers of 1-mm-thick composite resin (Filtek Z250, 3M ESPE). The restored dentin discs were sectioned into nine bonded beams with cross-sectional areas of approximately 0.9 mm2 and tested for microtensile bond strength (μTBS). The dentin surface of one fractured beam per tooth was submitted to MRS to characterize the physicochemical composition (n=10) at the interface. The data were analyzed using one-way analysis of variance and the Tukey-Kramer post hoc test (p<0.005).

Results:

MRS bioactive analyses revealed that both BG and BS promoted increased mineral matrix ratios in the CD and BD. Significantly higher μTBS values were found after CD treatment with BG (CD: 57 MPa±11; CD-BG: 78 MPa±15) and when BG and BS were applied to the BD (BD: 42 MPa±5; BD-BG: 71 MPa±14; BD-BS: 64 MPa±11) (p<0.005). The MRS analysis of the fractured dentin beam showed that the remineralization treatment significantly increased the dentin relative mineral concentration and promoted the appearance of new interface peaks, indicating a chemical interaction (p<0.005).

Conclusion:

Remineralization of BD is an effective therapy to restore damage caused by dentin bleaching and acid conditioning. This approach not only increases dentin mineral compounds but also improves dentin's ability to interact chemically with the adhesive system.

Evaluation of the influence of light-curing units on the degree of conversion in depth of a bulk-fill resin

Background

It is known that bulk-fill have been widely studied and used by dentists in the clinic. However, the use of light-curing units that do not have the ability to adequately light-cure these materials at the appropriate depth can affect their clinical performance. The aim of this study was evaluating the influence of 5 different light curing units (LCUs) on the degree of conversion (DC) of a bulk-fill resin at depths of 0 to 4 mm and determined the effect of using 20s exposure and 40s.

Material and Methods

Cylinders of composite were made in a stainless steel matrix (n=10). The specimens were exposed from the top surface using 5 LCUs: Valo® Cordless (VA); Radii Plus (RA); Emitter.D (EM), Biolux Plus (BI), Woodpecker® (WO). The emission wavelength and the power density was determined. After the photoactivation, the Raman vibrational modes were calculated taking as reference the peaks at 1,601 (aromatic bonds C=C) and 1,640 cm-1 (aliphatic bonds C=C).

Results

The largest difference in DC in 20s, comparing the values obtained in the first and last layer is for BI, with a variation from 61.24% to 53.86%. Comparing the LCUs, the last layer in 40s DC values are 57.40% (BI), 58.21% (WO), 58.97% (VA), 60.90% (RA) and 62.42% (EM). The higher the dose (J/cm²) and the close the λmax is to the maximum CQ absorption length (λmax ~ 470 nm) the better the DC value.

Conclusions

There was a significant difference in the DC values between the LCUs with increasing depth of the bulk-fill increments. Results indicate significant differences in DC among the different LCUs as well as enhanced DC when using 40s exposure compared to 20s. It is suggested that for DC improvement using lower power photoactivator increase the exposure time the exposure time should be 20s to 40s.

Key words:Polymerization, Composite Resins, Raman spectroscopy.

Abstract P5-03-08: Eribulin-induced EpCAM expression provides drug resistance in triple-negative breast cancer cells

Breast cancer is the most common cancer in women in the world. Among breast cancer subtypes, triple-negative breast cancer is aggressive. Because there is no effective therapy for triple-negative breast cancer, development of a novel therapeutic strategy is required.

Eribulin, a derivative of halicondrin B, is an anticancer chemical. Eribulin treatment has been approved in many countries for patients with metastatic or inoperable breast cancer, including triple-negative breast cancer. The known functions of Eribulin are inhibition of microtubule polymerization and induction of the expression of epithelial genes in breast cancer cells. However, the function of Eribulin-induced genes on the therapy for patients with triple-negative breast cancer remains unclear.

EpCAM (Epithelial cell adhesion molecule) is one of epithelial markers and known as a cell-cell adhesion molecule. In addition, EpCAM expression is involved in drug resistance in cancer. We therefore focused on EpCAM expression in Eribulin-treated breast cancer cells.

We used MDA-MB-231 cells that is a commonly used triple-negative breast cancer cell line. We treated cells with 10 nM Eribulin and observed inhibition of cell growth. In the same condition, we found up-regulation of EpCAM expression in both mRNA and protein levels. In mouse xenograft model with MDA-MB-231 cells, EpCAM expression was detected in whole tumor at 96 h after Eribulin administration. We analyzed the effect of other microtubule polymerization inhibitors, nocodazole and colchicine, on EpCAM induction. In the results, there was no up-regulation of EpCAM expression in cells treated with these chemicals, suggesting that EpCAM expression is not induced by inhibition of microtubule polymerization and growth inhibition.

To analyze EpCAM function on Eribulin treatment, we constructed shRNA-mediated EpCAM knockdown system. We introduced EpCAM knockdown in MDA-MB-231 cells and treated with Eribulin. In the results of cell growth assays, the cell number of Eribulin-treated EpCAM-knockdown cells was significantly smaller than that of Eribulin-treated control-shRNA cells, whereas no change was observed between solvent-treated control-shRNA and EpCAM-knockdown groups. In mouse xenograft experiments, EpCAM-knockdown cells showed smaller tumor weights than control-shRNA cells after administration of Eribulin. These results indicate that EpCAM expression provides Eribulin resistance in breast cancer cells.

In conclusion, we found Eribulin-induced EpCAM expression in triple-negative breast cancer cells. The EpCAM expression provides Eribulin resistance both in vitro and in vivo. These suggest that a combination of Eribulin treatment and EpCAM inhibition may improve therapy for breast cancer.

Citation Format: Tanaka S, Itou J, Sato F, Toi M. Eribulin-induced EpCAM expression provides drug resistance in triple-negative breast cancer cells [abstract]. In: Proceedings of the 2018 San Antonio Breast Cancer Symposium; 2018 Dec 4-8; San Antonio, TX. Philadelphia (PA): AACR; Cancer Res 2019;79(4 Suppl):Abstract nr P5-03-08.

Abstract P2-01-11: A peptide with the conserved amino acid residue of integrin α6 inhibits metastasis through disruption of complex formation in breast cancer cells

Metastasis inhibition may improve survival of breast cancer patients. Our previous study revealed that a transcription factor SALL4 promotes cell migration for metastasis through up-regulation of integrin α6β1 in metastatic basal-like breast cancer cells. In these cells, integrin α6β1 modulates Rho GTPase activity, which enhances focal adhesion dynamics for cell migration. We therefore focused on integrin α6 as a therapeutic target for metastasis.

We investigated the expression level of integrin α6 in breast cancer cell lines and a tissue microarray of breast cancer patients. In both experiments, we observed higher integrin α6 expression in basal-like breast cancer cells than in luminal ones. We performed shRNA-mediated integrin α6 knockdown in basal-like breast cancer cells and conducted Boyden chamber assays. In the results, reduced cell migration was observed in integrin α6 knocked-down cells. Reciprocally, we introduced integrin α6 overexpression in low-migratory luminal breast cancer cell lines and observed increased cell migration. These results indicate that integrin α6 promotes cell migration in breast cancer cells.

To identify the functional residue of integrin α6, we analyzed its amino acid sequence by in silico analyses. First, we extracted integrin α6 specific residues in integrin α family in the human genome. Then, we compared integrin α6 sequences among vertebrates. In the result, we obtained an integrin α6-specific and vertebrate-conserved sequence, Asp-358, as a candidate for the functional residue.

To inhibit integrin α6 function, we designed an 8-amino acid peptide with the sequence around Asp-358. Basal-like breast cancer cells treated with the peptide showed reduced cell migration in a dose-dependent manner. The peptide did not reduce cell migration in integrin α6 knocked-down cells, suggesting that the peptide inhibits integrin α6 function. To determine whether the peptide inhibits metastasis, we performed zebrafish metastasis assays, and observed reduced metastasis rate in the peptide-treated group. These results indicate that the peptide inhibits metastasis through reduction in cell migration.

To understand the effect of the peptide, we performed chemical cross-liking assay in a basal-like breast cancer cell line. Protein samples from the cells treated with a cross-linker showed bands of integrin α6 complexes, and the intensities of these bands were reduced in the peptide-treated group. Moreover, we immunostained cells with an antibody for focal adhesion marker, phospho-paxillin, because integrins regulates focal adhesion formation for cell migration. In the results, the peptide reduced the number of focal adhesions. These observations indicate that the peptide inhibits integrin α6 function. In the future, our findings may contribute to development of a metastasis inhibition therapy.

Citation Format: Itou J, Tanaka S, Senda N, Iida A, Sehara-Fujisawa A, Sato F, Toi M. A peptide with the conserved amino acid residue of integrin α6 inhibits metastasis through disruption of complex formation in breast cancer cells [abstract]. In: Proceedings of the 2018 San Antonio Breast Cancer Symposium; 2018 Dec 4-8; San Antonio, TX. Philadelphia (PA): AACR; Cancer Res 2019;79(4 Suppl):Abstract nr P2-01-11.

DESIGN IMPROVEMENT OF A LIQUID-MODERATOR-BASED NEUTRON SPECTROMETER FOR BNCT

Boron neutron capture therapy is known to be an effective radiation cancer therapy that requires neutron irradiation. A neutron field generated by an accelerator-based neutron source has various energy spectra, and it is necessary to evaluate the neutron spectrum in the treatment field. However, the method used to measure the neutron spectrum in the treatment field is not well established. Many researchers are making efforts to improve the spectrometers. To solve this problem, we are developing a liquid-moderator-based neutron spectrometer that is based on the same theory as that of the Bonner sphere spectrometer. The spectrometer uses a liquid moderator and absorber. In the present study, we performed a design study to improve the previously developed liquid-moderator-based neutron spectrometer. By carrying out a numerical simulation of the designed new spectrometer, we finally assessed and confirmed the validity of this spectrometer numerically.

Abstract PD2-07: Real-time navigation for sentinel lymph node biopsy in breast cancer patients using projection mapping with indocyanine green fluorescence

Background)

Sentinel lymph node (SLN) biopsy using indocyanine green fluorescence (fICG) method showed equal or better identification rate compared with blue dye or radioisotope (RI) method. In the fICG method, lymphatic vessels which drain into the SLNs can be seen through skin or subcutaneous tissue using near infrared camera (Photodynamic Eye®: PDE), and we can easily find the SLNs. However, whenever we observe the fluorescence images, we have to hold the PDE, turn off the operating light, and look at a monitor because fluorescence images cannot be seen directly. Medical imaging projection system (MIPS) is a new device which detects fluorescent emission from the organ and projects their images on the location of the fluorescence emission (Panasonic Connected Solutions Company, Japan). Projected images can be adjusted following the body movement or deformation of the organ. Therefore, MIPS could provide an option for real-time navigation for the SLN biopsy. The aim of this study was to evaluate the clinical utility of the MIPS.

Patients and methods)

Patients with clinically node-negative primary breast cancer underwent the fICG SLN biopsy using MIPS. Primary endpoint was identification rate of the fICG method using MIPS. At first, the study was conducted as an interventional study because the MIPS was the unapproved medical device. After approval of the MIPS, this study was conducted as an observational study. The study protocol was approved by the institutional review board at Kyoto University Hospital. All patients provided informed consent to participate in this study.

Results)

Between March 2016 and May 2017, 39 patients (40 procedures) underwent the fICG method SLN biopsy using MIPS. The median age was 55 years (range 32–74 years), and the median body mass index was 20.4 kg/m2 (range 17.7–27.7 kg/m2). About half had tumor stage T1 (58%) and 8 (20.0%) had DCIS. 8 procedures (20%) were performed after preoperative systemic therapy (PST). As MIPS itself can illuminate the operating field, SLN biopsy using MIPS was successfully performed without operating light in all procedures. At least one SLN was detected using MIPS for all procedures and the identification rate was 100% (95% CI: 91–100%). Median number of SLNs detected by MIPS was 3 (range 1–9) for all procedures, and 3 (range 2–8) for procedures after PST. Two pathologically positive SLNs and one SLN which included isolated tumor cells were detected by MIPS. In 25 procedures, RI was also used. 62 of 97 SLNs detected by MIPS (64%) were also detected by RI. However, no SLNs were detected only by RI.

Conclusions)

Although we still may not be able to avoid RI method because 25/40 (62.5%) procedures required the combined use of RI method, the fICG methods SLN biopsy using MIPS, which showed comparable identification rate of SLN with the conventional methods, could be useful tool with a view of allowing us to perform a real-time navigation surgery.

Acknowledgements)

This study was supported by Acceleration Transformative research for Medical innovation, Japan Agency for Medical Research and Development (AMED).

Citation Format: Takada M, Takeuchi M, Suzuki E, Sato F, Matsumoto Y, Torii M, Sakita-Kawaguchi N, Nakayama Y, Okuda T, Nishino H, Seo S, Hatano E, Toi M. Real-time navigation for sentinel lymph node biopsy in breast cancer patients using projection mapping with indocyanine green fluorescence [abstract]. In: Proceedings of the 2017 San Antonio Breast Cancer Symposium; 2017 Dec 5-9; San Antonio, TX. Philadelphia (PA): AACR; Cancer Res 2018;78(4 Suppl):Abstract nr PD2-07.

DEVELOPMENT OF ISOTOPICALLY ENRICHED BORON-DOPED ALUMINA DOSIMETER FOR THERMAL NEUTRONS

A novel optically stimulated luminescence (OSL) detector containing isotopically enriched boron was developed for thermal neutron dosimetry. Alumina containing isotopically enriched boron (Al2O3:B) was synthesised by the sol-gel method. The Al2O3:B was annealed up to ~1800 K. For X-ray diffractometer (XRD) analysis, the diffraction pattern of the Al2O3:B had reflex peaks corresponding to α-Al2O3. The sensitivity of Al2O3:B to photons was slightly 2% of that of a commercial Al2O3:C. The Al2O3:B detector had satisfactory linearity in X-ray dose measurement. A thermal neutron field was constructed using a 241Am-Be neutron source and graphite blocks. A pair of Al2O3:10B and Al2O3:11B detectors were set in the thermal neutron field. The response of Al2O3:10B was larger than that of Al2O3:11B owing to the 10B(n,α)7Li reactions. The sensitivity of Al2O3:10B to thermal neutrons was estimated to be two orders less than the photon sensitivity. Therefore, the pair of Al2O3:10B and Al2O3:11B detectors were useful for thermal neutron dosimetry.

Measurement of urinary concentrations of the mycotoxins zearalenone and sterigmatocystin as biomarkers of exposure in mares

Mycotoxins may affect animal health, including reproduction. Little is known about the clinical relevance of exposure of horses to contaminated feed. This study aimed at (i) monitoring the levels of the mycotoxins zearalenone (ZEN), with its metabolites α- and β-zearalenol (α- and β-ZOL), and sterigmatocystin (STC) in urine samples from thoroughbred mares in Japan and (ii) relating these findings to the potential effects on reproductive efficacy of breeding mares. Sixty-three urine samples of breeding mares from 59 breeding farms were used. Urine samples and reproductive records were collected from each mare when it was presented to the stallion station. Urinary concentrations of ZEN, α- and β-ZOL, and STC were measured using liquid chromatography-tandem mass spectrometry (LC-MS/MS). ZEN, α- and β-ZOL were measurable in the urine of all examined mares, indicating the prevalence of ZEN in equine feeds. In seven of the 63 samples, STC was also detected at levels ranging from 1.3 to 18.0 pg/mg creatinine. No significant correlation between the concentrations of mycotoxins and pregnancy status was observed. In conclusion, measurement of mycotoxins in urine samples is a useful non-invasive method for monitoring the systemic exposure of mares to multiple mycotoxins.

Variability and constraint of vertebral formulae and proportions in colugos, tree shrews, and rodents, with special reference to vertebral modification by aerodynamic adaptation

BACKGROUND

The aim of the present study is to provide the first large data set on vertebral formulae and proportions, and examine their relationship with different locomotive modes in colugos (Dermoptera), tree shrews (Scandentia), and rodents (Rodentia), which have been considered less variable because they were thought to have a plesiomorphic number of 19 thoracolumbar vertebrae.

MATERIALS AND METHODS

The data included 33 colugos and 112 tree shrews, which are phylogenetically sister taxa, and 288 additional skeletons from 29 other mammalian species adapted to different locomotive modes, flying, gliding, arboreal, terrestrial, digging, and semi-aquatic habitats.

RESULTS

The following results were obtained: (1) intra-/interspecies variability and geographical variation in thoracic, lumbar, and thoracolumbar counts were present in two gliding colugo species and 12 terrestrial/arboreal tree shrew species; (2) in our examined mammals, some aerodynamic mammals, such as colugos, southern flying squirrels, scaly-tailed squirrels, and bats, showed exceptionally high amounts of intraspecific variation of thoracic, lumbar, and thoracolumbar counts, and sugar gliders and some semi-aquatic rodents also showed some variation; (3) longer thoracic and shorter lumbar vertebrae were typically shared traits among the examined mammals, except for flying squirrels (Pteromyini) and scaly-tailed squirrels (Anomaluridae).

CONCLUSIONS

Our study reveals that aerodynamic adaptation could potentially lead to strong selection and modification of vertebral formulae and/or proportions based on locomotive mode despite evolutionary and developmental constraints. (Folia Morphol 2018; 77, 1: 44-56) Background: The aim of the present study is to provide the first large data set on vertebral formulae and proportions, and examine their relationship with different locomotive modes in colugos (Dermoptera), tree shrews (Scandentia), and rodents (Rodentia), which have been considered less variable because they were thought to have a plesiomorphic number of 19 thoracolumbar vertebrae.

MATERIALS AND METHODS

The data included 33 colugos and 112 tree shrews, which are phylogenetically sister taxa, and 288 additional skeletons from 29 other mammalian species adapted to different locomotive modes, flying, gliding, arboreal, terrestrial, digging, and semi-aquatic habitats.

RESULTS

The following results were obtained: (1) intra-/interspecies variability and geographical variation in thoracic, lumbar, and thoracolumbar counts were present in two gliding colugo species and 12 terrestrial/arboreal tree shrew species; (2) in our examined mammals, some aerodynamic mammals, such as colugos, southern flying squirrels, scaly-tailed squirrels, and bats, showed exceptionally high amounts of intraspecific variation of thoracic, lumbar, and thoracolumbar counts, and sugar gliders and some semi-aquatic rodents also showed some variation; (3) longer thoracic and shorter lumbar vertebrae were typically shared traits among the examined mammals, except for flying squirrels (Pteromyini) and scaly-tailed squirrels (Anomaluridae).

CONCLUSIONS

Our study reveals that aerodynamic adaptation could potentially lead to strong selection and modification of vertebral formulae and/or proportions based on locomotive mode despite evolutionary and developmental constraints. (Folia Morphol 2018; 77, 1: 44-56).

Chemical Interaction Analysis of an Adhesive Containing 10-Methacryloyloxydecyl Dihydrogen Phosphate (10-MDP) With the Dentin in Noncarious Cervical Lesions

The purpose of this study was to evaluate the chemical bonds of a self-etch 10-methacryloyloxydecyl dihydrogen phosphate (10-MDP) adhesive to natural noncarious cervical lesions (NCCLs) and compare them with those occurring in sclerotic dentin in artificially prepared defects (APDs). Four human teeth with natural NCCLs on the buccal surface were selected. Artificial defects matching the natural lesions were prepared on the lingual surface of the same teeth serving as control. Micro-Raman (MR) spectroscopy was used to quantify mineral content in natural NCCLs and in APDs. Fourier transform infrared-photoacoustic spectroscopy (FTIR-PAS) readouts were taken before and after adhesive application to analyze the protein matrix/mineral (M:M) ratio and chemical interactions between 10-MDP adhesive and dentin. The MR and FTIR-PAS spectra collected from natural NCCLs demonstrated a larger area of the band (961 cm−1, PO4) and lower M:M ratio, respectively, characterizing a hypermineralized dentin, compared with APDs. FTIR-PAS demonstrated emergence of a peak (1179 cm−1, P=O) in spectra after adhesive treatment, demonstrating a more intense chemical interaction in natural NCCLs. The results demonstrated that chemical bonding of 10-MDP adhesive to natural NCCLs is more intense, due to the hypermineralized surface, and suggest that it is unnecessary to remove the hypermineralized layer with burs, as this may decrease the chemical bonding potential of 10-MDP.

Measurement of Coherent π^{+} Production in Low Energy Neutrino-Carbon Scattering

We report the first measurement of the flux-averaged cross section for charged current coherent π^{+} production on carbon for neutrino energies less than 1.5 GeV, and with a restriction on the final state phase space volume in the T2K near detector, ND280. Comparisons are made with predictions from the Rein-Sehgal coherent production model and the model by Alvarez-Ruso et al., the latter representing the first implementation of an instance of the new class of microscopic coherent models in a neutrino interaction Monte Carlo event generator. We observe a clear event excess above background, disagreeing with the null results reported by K2K and SciBooNE in a similar neutrino energy region. The measured flux-averaged cross sections are below those predicted by both the Rein-Sehgal and Alvarez-Ruso et al.