Discoloration and Surface Changes in Spruce Wood after Accelerated Aging

Spruce wood is widely used in outdoor applications, but its susceptibility to degradation under exposure to sunlight and moisture is a major concern. This study investigates the impact of accelerated aging on spruce wood's surface chemistry, microstructure, geometry, and discoloration. The study was performed in two outdoor aging modes: dry and wet. The accelerated aging effects were evident in the changes in spruce wood structure, as well as in the other studied properties. During aging, it developed significant discoloration. Under simulated rainless outdoor conditions (dry mode), spruce wood gradually became dark brown. Under conditions involving rain (wet mode), the discoloration was qualitatively different from the dry mode. FTIR spectroscopy showed that during the accelerated aging of wood, lignin was mainly degraded, especially in the early stages of the process. A linear correlation was found between the changes in lignin and the color changes in the wood. There was an increase in carbonyl groups in the dry mode, which contributed to the color change and was also influenced by changes in extractives. The wet mode caused the leaching out of carbonyl groups. The observed decrease in cellulose crystallinity, together with the degradation of hydrophobic lignin, may result in the increased hydrophilicity of photodegraded wood. For both modes, there were different changes in the wood micro- and macrostructure, reflected in the surface morphology. The roughness increased during the aging process in both modes. The slightest changes in the roughness parameters were identified in the grain direction in the dry mode; the most evident was that the roughness parameters increased perpendicular to the grain in the wet mode. The demonstrated mechanism backing up the aging-related changes to the spruce wood structure and the relations unveiled between these changes and the changes in the spruce wood surface properties can provide an issue point for seeking ways how to mitigate the negative effects of the environmental factors the wood is exposed to.

Evaluation of Chemical and Morphological Properties of Spruce Wood Stored in the Natural Environment

This paper focuses on the changes in chemical structure and fiber morphological properties of spruce wood during 15 months of its storage in an open forest woodshed. From the chemical composition, the extractives, cellulose, holocellulose, and lignin content were determined. The pH value was measured on the wood surface using a contact electrode. Acetic and formic acid, saccharides (glucose, xylose, galactose, arabinose and mannose), and polymerization degree (PD) of cellulose were analyzed using the HPLC method. Fiber length and width were determined using a fiber tester analyzer. After 15 months of storage the content of both cellulose (determined by the Seifert method) and lignin did not change; the quantity of hemicelluloses decreased by 13.2%, due to its easier degradation and less stability compared to cellulose; and the pH value dropped by one degree. HPLC analyses showed a total decrease in the cellulose DP of 9.2% and in saccharides of 40.2%, while the largest decreases were recorded in the quantity of arabinose, by 72%, in the quantity of galactose, by 61%, and in the quantity of xylose, by 43%. Organic acids were not detected due to their high volatility during wood storage. The total decrease in average fiber length was 38.2% and in width was 4.8%. An increase in the proportion of shorter fibers, and a decrease in the proportion of longer fibers, was recorded. It can be concluded that fundamental changes occurred in the wood, which could affect the quality of further products (e.g., chips, pulp, paper, particleboards).

Experimental Investigation on Strength and Stiffness Properties of Laminated Veneer Lumber (LVL)

This study presents a testing campaign aimed at evaluating the strength and stiffness properties of laminated veneer lumber (LVL) specimens. LVL is an engineered wood product composed of thin glued wood veneers whose use in construction for structural applications has increased due to its sustainability and enhanced mechanical performance. Despite LVL's growing popularity, there is a lack of comprehensive information regarding stress-strain responses, failure modes, and the full set of strength and stiffness properties. These are particularly essential when LVL is employed in pure timber structures or composite systems such as steel-timber or timber-concrete load-bearing elements. This research aims to bridge this knowledge gap, focusing on crossbanded LVL panels, known as LVL-C, crafted from Scandinavian spruce wood, which is an LVL product with 20% of crossbanded veneers. The study explores LVL-C mechanical behavior in three primary orthogonal directions: longitudinal, tangential, and radial. A series of mechanical tests, including compression, tension, shear, and bending, was conducted to provide a thorough assessment of the material's performance. In compression tests, different behaviors were observed in the three directions, with the longitudinal direction exhibiting the highest stiffness and strength. Tensile tests revealed unique stress-strain responses in each direction, with gradual tension failures. Shear tests showcased varying shear stress-strain patterns and failure modes, while bending tests exhibited significant strength and stiffness values in flatwise bending parallel to the grain and flatwise bending perpendicular to the grain. This paper summarizes the comprehensive testing results and discusses the obtained strength and stiffness properties of LVL-C panels, providing valuable insights into their mechanical behavior for engineering applications.

Microfibrillated Cellulose with a Lower Degree of Polymerization; Synthesis via Sulfuric Acid Hydrolysis under Ultrasonic Treatment

A new approach is being considered for obtaining microfibrillated cellulose with a low degree of polymerization by sulfuric acid hydrolysis with simultaneous ultrasonic treatment under mild conditions (temperature 25 °C, 80% power control). Samples of initial cellulose, MCC, and MFC were characterized by FTIR, XRF, SEM, DLS, and TGA. It was found that a high yield of MFC (86.4 wt.%) and a low SP (94) are observed during hydrolysis with ultrasonic treatment for 90 min. It was shown that the resulting microfibrillated cellulose retains the structure of cellulose I and has an IC of 0.74. It was found that MFC particles are a network of fibrils with an average size of 91.2 nm. ζ-potential of an aqueous suspension of MFC equal to -23.3 mV indicates its high stability. It is noted that MFC has high thermal stability, the maximum decomposition temperature is 333.9 °C. Simultaneous hydrolysis process with ultrasonic treatment to isolate MFC from cellulose obtained by oxidative delignification of spruce wood allows to reduce the number of stages, reduce energy costs, and expand the scope.

Wood Surface Finishing with Transparent Lacquers Intended for Indoor Use, and the Colour Resistance of These Surfaces during Accelerated Aging

This work evaluates the effects of accelerated aging on the discolouration of surface-treated spruce wood and oak wood coated with solvent-based polyurethane lacquers, and surface-treated spruce wood coated with water-based transparent coating systems. All concerned coating materials were intended for indoor use. It was also explored how the colour stability of spruce wood and oak wood surfaces treated with solvent-based polyurethane lacquers was affected by wood surface layer modifications with pigment or stain mordants applied before these lacquers. Another issue studied was how the lignin stabilizer admixed into the primer and pigments admixed into the top coating layers affected the stability of water-based coating systems on spruce. The experimental results showed that the accelerated aging process with a simulation of indoor conditions induced significant discolouration of wood surfaces coated with solvent-based polyurethane lacquers and water-based coating systems. There were also confirmed significant impacts of all the studied factors (wood species, lacquer/coating system type, lacquer modification, wood pre-treatment with pigment and stain mordants). The spruce wood surfaces coated with solvent-based polyurethane lacquers were less stable (ΔE = 10-19, dependent on the lacquer type) than the oak surfaces treated in the same ways (ΔE = 4-11). There were also confirmed significant impacts of the particular surface treatment on the colour stability as well as significant impacts of wood surface pre-treatment with pigment and stain mordants (ΔE = 4-17-for spruce wood, and ΔE = 5.5-13-for oak wood). In the case of water-based lacquers, the ΔE values ranged between 3 and 11 (according to the coating system type). The results show that an appropriate UV absorbent combined with an appropriate lignin stabilizer and pigment mordant may enable attaining the required colour stability for a given surface treatment applied on a given wood species.

Relation of Chemical Composition and Colour of Spruce Wood

The visual inspection of fresh cut spruce wood (Picea abies, L. Karst.) showed the variability of its colour. Wood visual inspection is a part of wood quality assessment, for example, prior to or after its processing. The detail spruce wood colour analysis was performed using spectrophotometric data. The colour was measured by the bench-top spectrophotometer CM-5 Konica Minolta. The spectrophotometer was calibrated with a built-in white standard and on air. The whole analysis was performed in an xy chromaticity diagram supplemented with coordinate Y and CIE L*a*b* colour spaces. The ratio of the white chromophore amount to the amount of all achromatic chromophores is related to the Y coordinate. The ratio of the chromatic chromophore amount to all chromophores amount is saturation. The constructed model of the spruce wood colour is composed of four chromophores. The white chromophore belongs to holocellulose. The black chromophore belongs to lignin. The saturation is influenced by two chromophores. One of them belongs to extractives, another to lignin. The amounts of chromophores correlated with the spruce wood chemical composition. The chemical composition was measured using the procedures of Seifert, Wise, Sluiter, and ASTM. Moreover, the wood colour is affected by the moisture content.

Dry-Matter Loss and Changes in the Chemical Composition of Spruce Wood after Long-Term Storing in the Form of Roundwood

Wood stock in a warehouse is a necessary precondition for reliable manufacturing. However, wood can degrade and lose the matter during storage. "Dry-matter loss (DML)" is used to quantify the degradation following the changes in mass of a wood substance. The proposed calculation of DML is based on using parallel figures. The calculated loss of spruce wood substance harvested in winter during a six-month period was 4.5%. The estimated annual loss of wood substance was 5.7%. The loss was caused by a factor with a gradually eliminated effect. The changes in the chemical composition of wood substance were not proportional to the original amount of the isolated chemical substances. Hemicelluloses and lignin suffered from the loss faster than there was a change in the DML of spruce wood. Hemicelluloses were the most unstable isolated compound, with an increased rate of change during the first four months. The number of extractives significantly decreased during two months of storage. However, there was an increase in the number of extractives after six months of storage. The loss of cellulose was similar to the DML of spruce wood during the whole time of storage. The FTIR analysis confirmed a decrease in the total crystalline index (TCI) and lateral order index (LOI) of cellulose due to the storage of roundwood.

Statistical Modelling of the Fatigue Bending Strength of Norway Spruce Wood

When wood is used as a structural material, the fact that it is a highly inhomogeneous material, which significantly affects its static and fatigue properties, presents a major challenge to engineers. In this paper, a novel approach to modelling the fatigue-life properties of wood is presented. In the model, the common inverse-power-law relationship between the structural amplitude loads and the corresponding number of load cycles to failure is augmented with the influence of the wood’s mass density, the loading direction and the processing lot. The model is based on the two-parametric conditional Weibull’s probability density function with a constant shape parameter and a scale parameter that is a function of the previously mentioned parameters. The proposed approach was validated using the example of experimental static and fatigue-strength data from spruce beams. It turned out that the newly presented model is capable of adequately replicating the spruce’s S-N curves with a scatter, despite the relatively scarce amount of experimental data, which came from different production lots that were loaded in different directions and had a significant variation in density. Based on the experimental data, the statistical model predicts that the lower density wood has better fatigue strength.

Interaction between Thermal Modification Temperature of Spruce Wood and the Cutting and Fracture Parameters

This work examines the effect of thermal modification temperatures in the production of thermally modified wood on the cutting and fracture parameters when cutting heat-treated spruce wood by a circular sawblade machine. The samples were thermally modified at 160, 180, 200, and 220 °C. One sample was unmodified and was used as a reference sample. On the basis of the performed experiments, the fracture parameters (fracture toughness and shear yield strength) were calculated for the axial–perpendicular direction of cutting. In comparison with the theoretical assumptions, the influence of temperature on the cutting and fracture parameters was confirmed. Thermally treated wood is characterized by increased fragility and susceptibility to crack formation, as well as reduced density, bending strength, and shear strength. These properties significantly affect the size of the cutting force and feed force, as well as the fracture parameters. As the temperature increases, the values of these parameters decrease. The mentioned material characteristics could be useful for the optimization of the cutting process, as well as for the issue of energy consumption during the machining of heat-treated wood.

The Effect of Heat Flux to the Fire-Technical and Chemical Properties of Spruce Wood (Picea abies L.)

The paper assesses the influence of the heat flux on spruce wood (Picea abies L.) behavior. The heat flux was performed at 15, 20, 25, and 30 kW·m⁻². The fire-technical properties, such as the mass burning rate, charring thickness, charring rate, as well as the chemical composition (contents of the extractives, lignin, cellulose, holocellulose), of wood were determined. The highest burning rate of spruce wood of 0.32%·s⁻¹ was reached at the heat flux of 30 kW·m⁻². The charring rate ranged from 1.004 mm·min⁻¹ (15 kW·m⁻²) to 2.016 mm·min⁻¹ (30 kW·m⁻²). The proposed model of the charring process of spruce wood in time and appropriate thickness as a selected parameter is applicable in validation of the results of computer fire models in the design of fire protection of wooden buildings. The decrease in the holocellulose content mostly caused by the degradation of hemicelluloses was observed during thermal loading. The biggest decrease in hemicelluloses (24.94%) was recorded in samples loaded at 30 kW·m⁻². The contents of cellulose increased due to the structural changes (carbonization and crosslinking), the content of lignin increased as well due to its higher thermal stability compared to saccharides, as well as the resulting lignin condensation.

Chemical and Morphological Composition of Norway Spruce Wood (Picea abies, L.) in the Dependence of Its Storage

Chemical composition and morphological properties of Norway spruce wood and bark were evaluated. The extractives, cellulose, hemicelluloses, and lignin contents were determined by wet chemistry methods. The dimensional characteristics of the fibers (length and width) were measured by Fiber Tester. The results of the chemical analysis of wood and bark show the differences between the trunk and top part, as well as in the different heights of the trunk and in the cross section of the trunk. The biggest changes were noticed between bark trunk and bark top. The bark top contains 10% more of extractives and 9.5% less of lignin. Fiber length and width depends on the part of the tree, while the average of these properties are larger depending on height. Both wood and bark from the trunk contains a higher content of fines (fibers <0.3 mm) and less content of longer fibers (>0.5 mm) compared to the top. During storage, it reached a decrease of extractives mainly in bark. Wood from the trunk retained very good durability in terms of chemical composition during the storage. In view of the morphological characteristics, it occurred to decrease both average fibers length and width in wood and bark.

Acoustic Properties of Resonant Spruce Wood Modified Using Oil-Heat Treatment (OHT)

Wedge-shaped boards of spruce wood (Picea abies Karst.) are used to make violin fronts, also known as soundboards. Oil-heat treatment (OHT) can influence the acoustic properties of resonant wood, such as spruce. In this study, the effect of OHT on spruce wood was evaluated, using palm oil as a heating medium, at four different temperatures: 140, 160, 180 and 200 °C. Physical, mechanical and acoustic properties of spruce wood were evaluated before and after OHT and included the following: density, modulus of elasticity in the static bending test, and wood sound velocity. The acoustic parameters after OHT improved; however, the samples bent after modification had a higher modulus of elasticity, with a simultaneous deterioration of the acoustic parameters. The dynamic modulus of elasticity increased by 11%, and the musical constant by 5%. The static modulus increased by more than 3.5%, but the acoustic parameters calculated on the basis of these results indicated a deterioration of the acoustic properties of completely oven-dried wood. The increase in moisture content to air-dried condition contributed to a slight increase in the mean musical constant at the highest modification temperature.

Improvement of White Spruce Wood Dimensional Stability by Organosilanes Sol-Gel Impregnation and Heat Treatment

Wood is a living material with a dimensional stability problem. White spruce wood is a Canadian non-permeable wood that is used for siding applications. To improve this property, white spruce wood was treated with organosilanes sol-gel treatment with different moisture content (oven dried, air dried, and green wood). No major morphological changes were observed after treatment. However, organosilanes were impregnated into the cell wall without densifying the wood and without modifying the wood structure. Si-O-C chemical bonds between organosilanes and wood and Si-O-Si bonds were confirmed by FTIR and NMR, showing the condensation of organosilanes. The green wood (41% moisture content) showed only 26% dimensional stability due to the presence of too much water for organosilanes treatment. With a moisture content of 14%–18% (oven dried or air dried wood), the treatment was adapted to obtain the best improvement in dimensional stability of 35% and a 25% reduction of water vapor sorption. Finally, impregnation with organosilanes combined with the appropriate heat treatment improved the dimensional stability of white spruce wood by up to 35%. This treated Canadian wood could be an interesting option to validate for siding application in Canada.