The Influence of Q & T Heat Treatment on the Change of Tribological Properties of Powder Tool Steels ASP2017, ASP2055 and Their Comparison with Steel X153CrMoV12

In connection with the growing importance of the efficiency and reliability of tools in industrial sectors, our research represents a key step in the effort to optimize production processes and increase their service life in real conditions. The study deals with the comparison of the tribological properties of three tool steels, two of which were produced by the powder metallurgy method-ASP2017 and ASP2055-and the last tool steel underwent the conventional production method-X153CrMoV12. The samples were mechanically machined with the finishing technology of turning and, finally, heat treated (Q + T). The study focused on the evaluation of hardness, resulting microstructure, wear resistance, and coefficient of friction (COF). The ball-on-disc method was chosen as part of the COF and wear resistance test. The tribological test took place at room temperature with dry friction to accelerate surface wear. The pressing material was a hardened steel ball G40 (DIN 100Cr6). Measurements were performed at loads of 10 N, 6 N, and 2 N and turning radii of 13 mm, 18 mm, and 23 mm, which represents a peripheral speed of 0.34, 0.47, and 0.60 m/s. The duration of the measurement for each sample was 20 min. The results showed that the COF of powder steels showed almost the same values, while a significant difference occurred with the increase of the radius rotation in the case of conventional steel. The results within the friction mechanism showed two types of wear, namely, adhesive and abrasive wear, depending on the Q + T process. From a tribological point of view in terms of wear, it was possible to state that the material ASP2055 after Q + T showed the lowest rate of wear of all the tested steels.

Pathways toward the Use of Non-Destructive Micromagnetic Analysis for Porosity Assessment and Process Parameter Optimization in Additive Manufacturing of 42CrMo4 (AISI 4140)

Laser-based powder bed fusion of metals (PBF-LB/M) is a widely applied additive manufacturing technique. Thus, PBF-LB/M represents a potential candidate for the processing of quenched and tempered (Q&T) steels such as 42CrMo4 (AISI 4140), as these steels are often considered as the material of choice for complex components, e.g., in the toolmaking industry. However, due to the presence of process-induced defects, achieving a high quality of the resulting parts remains challenging in PBF-LB/M. Therefore, an extensive quality inspection, e.g., using process monitoring systems or downstream by destructive or non-destructive testing (NDT) methods, is essential. Since conventionally used downstream methods, e.g., X-ray computed tomography, are time-consuming and cost-intensive, micromagnetic NDT measurements represent an alternative for ferromagnetic materials such as 42CrMo4. In this context, 42CrMo4 samples were manufactured by PBF-LB/M with different process parameters and analyzed using a widely established micromagnetic measurement system in order to investigate potential relations between micromagnetic properties and porosity. Using multiple regression modeling, relations between the PBF-LB/M process parameters and six selected micromagnetic variables and relations between the process parameters and the porosity were assessed. The results presented reveal first insights into the use of micromagnetic NDT measurements for porosity assessment and process parameter optimization in PBF-LB/M-processed components.

Processing of Niobium-Alloyed High-Carbon Tool Steel via Additive Manufacturing and Modern Powder Metallurgy

Niobium is recently considered one of the potential alloying elements for tool steels due to the formation of hard and stable carbides of MC type. Its use is limited by the fact that these carbides tend to coarsen during conventional melting metallurgy processing. This work explores the potential of additive manufacturing for processing Nb-alloyed tool steel with a high content of carbon. Directed energy deposition was used as the processing method. It was found that this method allowed us to obtain a microstructure very similar to that obtained after the use of consolidation via spark plasma sintering when subsequent heat treatment by soft annealing, austenitizing, oil quenching and triple tempering for secondary hardness was applied. Moreover, the soft annealing process could be skipped without affecting the structure and properties when machining would not be required. The hardness of the steel was even higher after additive manufacturing was used (approx. 800-830 HV 30) than after spark plasma sintering (approx. 720-750 HV 30). The wear resistance of the materials processed by both routes was almost comparable, reaching 5-7 × 10^-6 mm³N^-1m^-1 depending on the heat treatment.

Novel Pectin Binder for Satelliting Carbides to H13 Tool Steel for PBF-LB Processing

In order to enhance the range of processable alloys of laser-based powder bed fusion, reinforced alloys have gained focus. Satelliting is a recently introduced method for adding fine additives to larger parent powder particles using a bonding agent. Satellited particles prevent a local demixing due to size and density effects of the powder. In this study, the satelliting method is used for the additivation of Cr₃C₂ to AISI H13 tool steel via a functional polymer binder (pectin). The investigation includes a detailed binder analysis and comparison to the previously used PVA binder as well as processability in PBF-LB and the microstructure of the alloy. The results reveal that pectin is a suitable binder for the satelliting process and the demixing behavior that appears when using a simple powder blend can be significantly reduced. However, the alloy is enriched with carbon, which results in austenite being retained. Thus, in future research, a reduced binder content will be investigated.

Impact of Particle Size Distribution in the Preform on Thermal Conductivity, Vickers Hardness and Tensile Strength of Copper-Infiltrated AISI H11 Tool Steel

Spontaneous infiltration of a porous preform by a metallic melt provides the potential of generating metal matrix composites (MMCs) with tailored combinations of material properties at low cost. The bulk of tool inserts for injection molding must sustain high mechanical and thermal loads and simultaneously exhibit high thermal conductivity for efficient temperature control of the mold insert. To fulfill these contradictory requirements, AISI H11 tool steel preforms were infiltrated by liquid copper. The impact of the fine powder fraction (0 wt.% to 15 wt.%) blended to a coarse H11 powder in the preform on thermal conductivity, Vickers hardness and tensile strength was elucidated. The thermal conductivity of the composites could be enhanced by a factor of 1.84 (15 wt.% fine powder) and 2.67 (0 wt.% fine powder) with respect to the sintered H11 tool steel. By adding 15 wt.% fine powder to the coarse host powder, the tensile strength and Vickers hardness of the copper-infiltrated steel were 1066.3 ± 108.7 MPa and 366 ± 24 HV1, respectively, whereas the H11 tool steel yielded 1368.5 ± 89.3 MPa and 403 ± 17 HV1, respectively. Based on the results obtained, an appropriate particle size distribution (PSD) may be selected for preform preparation according with the requirements of a future mold insert.

Growth Kinetics, Microstructure Evolution, and Some Mechanical Properties of Boride Layers Produced on X165CrV12 Tool Steel

The powder-pack boriding technique with an open retort was used to form borided layers on X165CrV12 tool steel. The process was carried out at 1123, 1173, and 1223 K for 3, 6, and 9 h. As a result of boriding the high-chromium substrate, the produced layers consisted of three zones: an outer FeB layer, an inner Fe₂B layer, and a transition zone, below which the substrate material was present. Depending on the applied parameters of boriding, the total thickness of the borided layers ranged from 12.45 to 78.76 µm. The increased temperature, as well as longer duration, was accompanied by an increase in the thickness of the FeB zone and the total layer thickness. The integral diffusion model was utilized to kinetically describe the time evolution of the thickness of the FeB and (FeB + Fe₂B) layers grown on the surface of powder-pack borided X165CrV12 steel. The activation energy of boron for the FeB phase was lower than that for the Fe₂B phase. This suggested that the FeB phase could be formed before the Fe₂B phase appeared in the microstructure. The high chromium concentration in X165CrV12 steel led to the formation of chromium borides in the borided layer, which increased the hardness (21.88 ± 1.35 GPa for FeB zone, 17.45 ± 1.20 GPa for Fe₂B zone) and Young's modulus (386.27 ± 27.04 GPa for FeB zone, 339.75 ± 17.44 GPa for Fe₂B zone). The presence of the transition zone resulted from the accumulation of chromium and carbon atoms at the interface between the tips of Fe₂B needles and the substrate material. The presence of hard iron and chromium borides provided significant improvement in the wear resistance of X165CrV12 steel. The powder-pack borided steel was characterized by a four times lower mass wear intensity factor and nine times lower ratio of mass loss to the length or wear path compared to the non-borided material.

Optimization of Process Parameters for the Laser Polishing of Hardened Tool Steel

In mold making, the mold surface roughness directly affects the surface roughness of the produced part. To achieve surface roughness below 0.8 μm, the cost of surface finish is high and time-consuming. One alternative to the different grinding and polishing steps is laser polishing (LP). This study investigates and models the LP of tool steel (X38CrMoV5-1-DIN 1.2343), typical for the mold industry, having an initial rough surface obtained by electrical discharge machining. The microstructures of the re-melted layer and heat-affected zone due to the LP process were also studied. Four parameters: the laser spot size, velocity, maximum melt pool temperature and overlapping were investigated via a design of experiments (DoE) approach, specifically a factorial design. The responses were line roughness (Ra), surface roughness (Sa), and waviness (Wa). The surface topography was measured before and after the LP process by white light profilometer or confocal microscopy. DoE results showed that the selected factors interact in a complex manner, including the interactions, and depend on the responses. The DoE analysis of the results revealed that the roughness is mainly affected by the velocity, temperature and overlap. Based on a first DoE model, an optimization of the parameters was performed and allowed to find optimum parameters for the LP of the rough samples. The optimum conditions to minimize the roughness are a spot size of 0.9 mm, a velocity of 50 mm/s, a temperature of 2080 °C and an overlap of 90%. By using these parameters, the roughness could be reduced by a factor of almost 8 from 3.8 µm to approximately 0.5 µm. Observations of the microstructure reveal that the re-melted layer consists of columnar grains of residual austenite. This can be explained by the carbon intake of the electro-machined surface that helps stabilize the austenitic phase.

Approach to Estimate the Phase Formation and the Mechanical Properties of Alloys Processed by Laser Powder Bed Fusion via Casting

A high-performance tool steel with the nominal composition Fe85Cr4Mo8V2C1 (wt%) was processed by three different manufacturing techniques with rising cooling rates: conventional gravity casting, centrifugal casting and an additive manufacturing process, using laser powder bed fusion (LPBF). The resulting material of all processing routes reveals a microstructure, which is composed of martensite, austenite and carbides. However, comparing the size, the morphology and the weight fraction of the present phases, a significant difference of the gravity cast samples is evident, whereas the centrifugal cast material and the LPBF samples show certain commonalities leading finally to similar mechanical properties. This provides the opportunity to roughly estimate the mechanical properties of the material fabricated by LPBF. The major benefit arises from the required small material quantity and the low resources for the preparation of samples by centrifugal casting in comparison to the additive manufacturing process. Concluding, the present findings demonstrate the high attractiveness of centrifugal casting for the effective material screening and hence development of novel alloys adapted to LPBF-processing.

Processability of a Hot Work Tool Steel Powder Mixture in Laser-Based Powder Bed Fusion

Powder bed fusion of metals using a laser beam system (PBF-LB/M) of highly complex and filigree parts made of tool steels is becoming more important for many industrial applications and scientific investigations. To achieve high density and sufficient chemical homogeneity, pre-alloyed gas-atomized spherical powder feedstock is used. For high-performance materials such as tool steels, the number of commercially available starting powders is limited due to the susceptibility to crack formation in carbon-bearing steels. Furthermore, scientific alloy development in combination with gas-atomization is a cost-intensive process which requires high experimental effort. To overcome these drawbacks, this investigation describes the adaption of a hot work tool steel for crack-free PBF-LB/M-fabrication without any preheating as well as an alternative alloying strategy which implies the individual admixing of low-cost aspherical elemental powders and ferroalloy particles with gas-atomized pure iron powder. It is shown that the PBF-LB/M-fabrication of this powder mixture is technically feasible, even though the partly irregular-shaped powder particles reduce the flowability and the laser reflectance compared to a gas-atomized reference powder. Moreover, some high-melting alloying ingredients of the admixed powder remain unmolten within the microstructure. To analyze the laser energy input in detail, the second part of the investigation focuses on the characterization of the individual laser light reflectance of the admixed alloy, the gas-atomized reference powder and the individual alloying elements and ferroalloys.

PBF-EB of Fe-Cr-V Alloy for Wear Applications

Due to the small variety of materials, the areas of application of additive manufacturing in the toolmaking industry are currently still limited. In order to overcome these material restrictions, AM material development for high carbon-containing iron-based materials, which are characterized by high strength, hardness, and wear resistance, must be intensified. However, these materials are often susceptible to crack formation or lack of fusion defects during processing. Therefore, these materials are preferentially suited for electron beam powder bed fusion (PBF-EB). In this paper, an Fe-Cr-V alloy with 10% vanadium is presented. Investigations were carried out on the PBF-EB system Arcam A2X. Specimens and demonstrators are characterized by a three-phase microstructure with an Fe-rich matrix and VC and M₇C₃ reinforcements. The resulting microstructures were characterized by scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). Furthermore, mechanical and physical properties were measured. A final field test was conducted to evaluate durability in use.

Effect of Sandblasting on Static and Fatigue Strength of Flash Butt Welded 75Cr4 Bandsaw Blades

The aim of the research presented in this article is analysis of the effect of the surface treatment method on the static and fatigue strength of flash butt welded bandsaw blades. A 1-mm-thick 75Cr1 cold-work tool steel sheet used for bandsaw blades was used as the test material. Fractographic studies of the fatigue fractures and fractures formed in static tests were also carried out. The static strength tests showed sandblasting the weld surface had no significant effect on the load capacity of the joint. However, the sandblasted specimens showed a higher repeatability of the load capacity (lower standard deviation). In the case of both analyzed sample variants of specimens, sandblasted and non-sandblasted, the number of cycles at which the sample was damaged decreases with the percentage increase of the stress amplitude. When loading the samples with a stress amplitude value in the range between 400 and 690 MPa, sandblasting of the weld surface increased the average value of destructive cycles by about 10-86% (depending on the stress amplitude) compared to non-sandblasted joints. The sandblasting process introduces compressive stresses in the surface layer of the welds, therefore the variable tensile load acting on the sample requires a greater number of cycles before the fatigue cracks initiate and propagate. In the case of all specimens, a ductile fracture was observed. It was also found that, regardless of the variable stress amplitude, sandblasting has a positive effect on reducing the standard deviation of fatigue test results.

Influence of Selective Laser Melting Technology Process Parameters on Porosity and Hardness of AISI H13 Tool Steel: Statistical Approach

The correct setting of laser beam parameters and scanning strategy for Selective Laser Melting (SLM) technology is a demanding process. Usually, numerous experimental procedures must be taken before the final strategy can be applied. The presented work deals with SLM technology and the impact of its technological parameters on the porosity and hardness of AISI H13 tool steel. In this study, we attempted to map the dependency of porosity and hardness of the tested tool steel on a broad spectrum of scanning speed-laser power combinations. Cubic samples were fabricated under parameters defined by full factorial DOE, and metallurgic specimens were prepared for measurement of the two studied quantities. The gathered data were finally analyzed, and phenomenological models were proposed. Analysis of the data revealed a minimal energy density of 100.3 J/mm3 was needed to obtain a dense structure with a satisfactory hardness level. Apart from this, the model may be used for approximation of non-tested combinations of input parameters.

Influence of Intermediate Annealing Treatment on the Kinetics of Bainitic Transformation in X37CrMoV5-1 Steel

Intermediate annealing treatment (IAT) is a new process that accelerates the bainitic transformation in steels. This stimulation is crucial, especially in the prolonged production of nanobainitic steels. Among other recognised methods, it seems to be an effective and economical process. However, there are very few research works in this area. The objective of this study was to collate microstructural changes caused by IAT with differences in the kinetics of the subsequent bainitic transformation in the X37CrMoV5-1 tool steel. Differential dilatometry, LM and SEM microscopic observations, EDS and XRD analysis, and computer simulations were used to investigate the effect of IAT on the kinetics of bainitic transformation. The study has revealed that introducing an additional isothermal heating stage immediately after austenitising significantly affects the kinetics of bainitic transformation—it can accelerate or suppress it. The type and strength of the effect depends on the concentration, distribution, and morphology of the precipitations that occurred during IAT.

Enabling Micro Injection Moulding Using a Soft Tooling Process Chain with Inserts Made of Mortar Material

The manufacturing of inserts for micro injection moulding made of mortar material is presented in this work. The fabrication of the mortar insert described in this publication relied on a versatile and relatively fast rapid prototyping process based on soft tooling. The mortar insert has a QR code with micro features on its surface, which was replicated in acrylonitrile butadiene styrene (ABS) polymer by the micro injection moulding process. With this approach, it is possible to fabricate hard inserts for micro injection moulding purposes that are able to compete with conventional-made inserts made of tool steel.

Influence of Different Alloying Strategies on the Mechanical Behavior of Tool Steel Produced by Laser-Powder Bed Fusion

Additive manufacturing is a high-potential technique that allows the production of components with almost no limitation in complexity. However, one of the main factors that still limits the laser-based additive manufacturing is a lack of processable alloys such as carbon martensitic hardenable tool steels, which are rarely investigated due to their susceptibility to cold cracking. Therefore, this study aimed to expand the variety of steels for laser powder bed fusion (L-PBF) by investigating an alternative alloying strategy for hot work tool steel powder. In this study, a comprehensive investigation was performed on the powder and L-PBF processed specimen properties and their correlation with the existing defects. Cubical specimens were created using the following two alloying strategies by means of L-PBF: conventional pre-alloyed gas-atomized powder and a mixture of gas-atomized powder with mechanically crushed pure elements and ferroalloys. The influence of the particle parameters such as morphology were correlated to the defect density and resulting quasi-static mechanical properties. Micromechanical behavior and damage evolution of the processed specimens were investigated using in situ computed tomography. It was shown that the properties of the L-PBF processed specimens obtained from the powder mixture performs equal or better compared to the specimens produced from conventional powder.

Microstructural and Mechanical Evaluation of a Cr-Mo-V Cold-Work Tool Steel Produced via Electron Beam Melting (EBM)

In this work, a highly alloyed cold work tool steel, Uddeholm Vanadis 4 Extra, was manufactured via the electron beam melting (EBM) technique. The corresponding material microstructure and carbide precipitation behavior as well as the microstructural changes after heat treatment were characterized, and key mechanical properties were investigated. In the as-built condition, the microstructure consists of a discontinuous network of very fine primary Mo- and V-rich carbides dispersed in an auto-tempered martensite matrix together with ≈15% of retained austenite. Adjusted heat treatment procedures allowed optimizing the microstructure by the elimination of Mo-rich carbides and the precipitation of fine and different sized V-rich carbides, along with a decrease in the retained austenite content below 2%. Hardness response, compressive strength, and abrasive wear properties of the EBM-manufactured material are similar or superior to its as-HIP forged counterparts manufactured using traditional powder metallurgy route. In the material as built by EBM, an impact toughness of 16-17 J was achieved. Hot isostatic pressing (HIP) was applied in order to further increase ductility and to investigate its impact upon the microstructure and properties of the material. After HIPing with optimized protocols, the ductility increased over 20 J.

Microstructures and Mechanical Properties of Deposited Fe-8Cr-3V-2Mo-2W on SCM420 Substrate Using Directed Energy Deposition and Effect of Post-Heat Treatment

In this study, the Fe-8Cr-3V-2Mo-2W tool steel powder was deposited on the SCM420 substrate through the directed energy deposition (DED) process. This study focuses on the mechanical properties of the deposited Fe-8Cr-3V-2Mo-2W and the effect of heat treatment on it. The changes in the microstructural characteristics of the deposited region due to heat treatment after deposition were observed. The influence of heat treatment on the mechanical properties was then analyzed accordingly and hence, the hardness, wear, impact and tensile tests were conducted on the deposited material. These properties were compared with those of the commercial tool steel powder M2-deposited material and the carburized specimen. In the deposited Fe-8Cr-3V-2Mo-2W layer, an increased martensite phase fraction was obtained through post-heat treatment and the amount of precipitated carbides was also increased. This increased the hardness from 48 to 62 HRc after heat treatment and the wear resistance was significantly improved as well. The amount of impact energy absorbed decreased from 11 J before heat treatment to 6 J after heat treatment, but the tensile strength significantly increased from 607 to 922 MPa. When compared with the M2-deposited surface, the Fe-8Cr-3V-2Mo-2W deposits had 3% lower surface hardness and 76% lower fracture toughness but exhibited 56% higher tensile strength. When compared with the carburized SCM420, the Fe-8Cr-3V-2Mo-2W deposits exhibited 3% higher surface hardness and wear resistance, 90% lower fracture toughness and 5% higher tensile strength. This study shows that surface hardening through DED can exhibit similar or superior mechanical properties when compared to carburizing.

Dry Sliding Friction of Tool Steels and Their Comparison of Wear in Contact with ZrO2 and X46Cr13

Tool steels are used in stamping, shearing processes, and as cutting tools due to their good mechanical properties. During their working cycle, steels are subject to aggressive conditions such as heat stress, fatigue, and wear. In this paper, three tool steels, namely X153CrMoV12, X37CrMoV5-1, and X45NiCrMo4 were selected against two types of bearing balls, ZrO₂ and X46Cr1. All measurements were performed on a UMT TriboLab universal tribometric instrument under dry conditions. The main objective of the experiment was to analyze and compare tool steel wear in contact with two kinds of bearing balls with a diameter of 4.76 mm. This evaluation is focused on the hardness, surface roughness, and microstructure of all samples and on the impact of the input parameters on the resulting wear. All three types of tool steels were measured in the basic annealed state and, subsequently, in the state after hardening and tempering. Experimental results show that tool steels, belonging to high strength steels, can successfully represent wear resistant steels. The content of carbide elements, their size, and shape in the microstructure play an important role in the friction process and subsequent wear. Three types of loads were used and compared in the experiments 30, 60, and 90 N. Increasing the load results in significant degradation of the material on the sample surface. Lastly, the impact of hardness and roughness of materials on wear has also been proven. If abrasive wear occurs in the friction process, there is a greater degree of wear than that of adhesive wear. This is due to less abrasive particles, which behave like a cutting wedge and are subject to subsequent deformation strengthening due to the load increase, which adversely affects the further friction process. Analysis of the results showed that the ZrO₂ ceramic ball showed significantly better wear values when compared to the X46Cr13 stainless steel ball. It also improves the values of the coefficient of friction with respect to the type of wear that occurs when the experimental materials and counterparts are in contact.

Micro-Texture Analyses of a Cold-Work Tool Steel for Additive Manufacturing

Small objects of an alloy tool steel were built by selective laser melting at different scan speeds, and their microstructures were analyzed using electron backscatter diffraction (EBSD). To present an explicit correlation with the local thermal cycles in the objects, prior austenite grains were reconstructed using the EBSD mapping data. Extensive growth of austenitic grains after solidification could be detected by the disagreement between the networks of carbides and austenite grain boundaries. A rapid laser scan at 2000 mm/s led to less growth, but retained a larger amount of austenite than a slow one at 50 mm/s. The rapid scan also exhibited definite evolution of Goss-type textures in austenite, which could be attributed to the growth of austenitic grains under a steep temperature gradient. The local variations in the microstructures and the textures enabled us to speculate the locally different thermal cycles determined by the different process conditions, that is, scan speeds.

Impact of Mechanical Processes as a Pre-Sulphonitriding Treatment on Tribology Properties of Selected P/M Tool Steels

We have evaluated phase composition changes in the surface layer (SL) and wear resistance of steels investigated after various mechanical processes such as a pre-sulphonitriding treatments. Two various paths of surface modification were employed: Grinding–sulphonitriding (G-SN) and hard turning–slide burnishing–sulphonitriding (T-B-SN). Studies were carried out on Vanadis 8 and Vancron 40 tool steels, which are classified as advanced powder metallurgy (P/M) high-alloyed steels with different types and amounts of carbides. Heat treatment to the final hardness of 64 ± 1 HRC (Vanadis 8) and 62 ± 1 HRC (Vancron 40) was performed in vacuum furnaces with gas quenching. Precipitation of different types such as sulfides, nitrides, and carbides was observed using X-ray diffraction analysis. Tribological properties of SL were evaluated by pin-on-disc experiments. Pins of Al₂O₃ and 19MnB4 steel were used as counterbodies materials. 3D surface geometrical structure measurements were also performed. Wear tracks and cross-sections of SL were observed using optical and scanning electron microscopy. The three-stage process increases the wear resistance about 37% and 30%, respectively for Vanadis 8 and Vancron 40 (in case of alumina pins), whereas values of wear rates after tests performed against steel pins were very similar for two compared processes for both steels.

Improvement of Adhesive Wear Behavior by Variable Heat Treatment of a Tool Steel for Sheet Metal Forming

Vanadis 10 steel is a powder metallurgy (PM) processed tool steel. It is a ledeburitic steel with 8% Cr and 10% V. By deliberately varying the process parameters related to the quenching, tempering, and nitriding of these steels, the aim of this study is to determine which of these parameters have a significant influence on its adhesive wear resistance. The research methodology employed was a Design of Experiments (DoE) with six factors and two levels for each factor. The tempering temperature, number of temperings, and carrying out of a thermochemical nitriding treatment were found to have a significant effect. To increase adhesive wear resistance, austenitization at 1100 °C with air cooling is recommended, followed by three temperings at 500 °C and a subsequent nitriding treatment. It should be noted that the quench cooling medium does not have a significant influence on wear resistance. Furthermore, (Fe,Cr)₇C₃ (M₇C₃ carbides) are transformed into carbonitrides during nitriding. However, (Fe,V)C (MC carbides) are not affected by this nitriding process.

Effect of Plasma Nitriding Pretreatment on the Mechanical Properties of AlCrSiN-Coated Tool Steels

Surface modification of steel has been reported to improve hardness and other mechanical properties, such as increase in resistance, for reducing plastic deformation, fatigue, and wear. Duplex surface treatment, such as a combination of plasma nitriding and physical vapor deposition, achieves superior mechanical properties and resistance to wear. In this study, the plasma nitriding process was conducted prior to the deposition of hard coatings on the SKH9 substrate. This process was done by a proper mixture of nitrogen/hydrogen gas at suitable duty cycle, pressure, and voltage with proper temperature. Later on, the deposition of gradient AlCrSiN coatings synthesized by a cathodic-arc deposition process was performed. During the deposition of AlCrSiN, CrN, AlCrN/CrN, and AlCrSiN/AlCrN were deposited as gradient interlayers to improve adhesion between the coatings and nitrided steels. A repetitive impact test (200k⁻400k times) was performed at room temperature and at high temperature (~500 °C) to assess impact resistance. The results showed that the tribological impact resistance for the synthesized AlCrSiN increased because of a progressive hardness support. The combination of plasma nitriding and AlCrSiN hard coatings is capable of increasing the life of molding dies and metal forging dies in mass production.