Phytotoxic effects of chromium and tannery effluent on growth and metabolism of Phaseolus mungo Roxb

The various dilution levels of treated tannery effluent (T.E.) (10, 25, 50 and 100%) and Cr6+ (0.5, 2.0, 5.0 and 10 ppm) were used in experiment to know their effect on seed germination, seedling growth, pigments and enzymes content in Black gram (Phaseolus mungo Roxb.). Chromium is known as the main toxic component of tannery effluent so its various concentration were given to know their effects. For the recovery of plant damage, protective value of 10 and 25 ppm of zinc, potassium and iron sulphate were also given with 50% treated tannery effluent and 10 ppm Cr6+ levels in separate petridishes. The different concentrations of tannery effluent and Cr6+ showed significant reduction in germination percentage, seedling growth (plumule and radicle length, number of lateral roots, fresh and dry weight, and moisture %) and pigments (chlorophyll, pheophytin and carotenoids) with increase in concentrations. The lower doses of tannery effluent (10%) and Cr6+ (0.5, 2 and 5 ppm) slightly increases the pigments concentration. The amylase activity and total sugar contents were also significantly decreased while catalase and peroxidase activity showed significant increase with rise in concentrations of treatments. The lower concentrations of tannery effluent (dilution 10 and 25%) and Cr6+ (0.5 and 2 ppm) showed significant increase in total protein contents while decrease at higher concentrations. The zinc, potassium and iron treatments led to recover the damage caused by chromium and tannery effluent in all parameters. In recovery treatments zinc showed highest and significant recovery in maximum parameters. Iron also showed almost similar effect to the zinc while potassium showed minimum recovery.

The use of microemulsions to remove chromium from industrial sludge

In this work microemulsion systems were used to remove chromium from leather tannery sediments. The sludge was treated by a solid-liquid extraction process (acid digestion). The effects of particle size, digestion temperature and digestion time with regards to the efficiency of chromium removal were considered. The raw sludge (3 Mesh) was dried, grounded and sieved. Particles with 3, 14, 65, 100, 200, and 325 Mesh were evaluated. Sludge digestion solutions were prepared using each studied granule size at 25 degrees C, 70 degrees C, and 95 degrees C. Microemulsion extraction experiments to remove chromium III from the acid digestion solution were made according to a Scheffé Net experimental design methodology, using microemulsion systems inside the Winsor II region (System I) and inside the microemulsion region (Winsor IV--System II). A statistical treatment was used to obtain the isoresponse plots. Chromium extraction percentages were up to 73.3% for System I and up to 93.4% for System II.

Electrocoagulation efficiency of the tannery effluent treatment using aluminium electrodes

An electro-coagulation laboratory scale system using aluminium plates electrodes was studied for the removal of organic and inorganic pollutants as a by-product from leather finishing industrial process. A fractional factorial 2(3) experimental design was applied in order to obtain optimal values of the system state variables. The electro-coagulation (EC) process efficiency was based on the chemical oxygen demand (COD), turbidity, total suspended solid, total fixed solid, total volatile solid, and chemical element concentration values. Analysis of variance (ANOVA) for final pH, total fixed solid (TFS), turbidity and Ca concentration have confirmed the predicted models by the experimental design within a 95% confidence level. The reactor working conditions close to real effluent pH (7.6) and electrolysis time in the range 30-45 min were enough to achieve the cost effective reduction factors of organic and inorganic pollutants' concentrations. An appreciable improvement in COD removal efficiency was obtained for electro-coagulation treatment. Finally, the technical-economical analysis results have clearly shown that the electro-coagulation method is very promising for industrial application.

Tannery wastewater pre-treatment

Tannery wastewater is one of the most pollution sources. It can cause environmental problems related to its high organic matter, suspended solids and chromium. Chromium (III) salts are the most widely used chemicals for tanning processes, causing the tannery wastewater to be highly pollutant with chromium. The main objective of this study is to investigate the pre-treatment of an actual Egyptian tannery wastewater using two systems; the first electrolytic system and the second physico-chemical system. The performances of electrolytic system at current of 10, 20, 30 and 40 A were discussed. Poor removal efficiencies of chemical oxygen demand (COD), total suspended solids (TSS), chromium (III), ammonia (NH(4) (+) and sulfide (S(2-)) were obtained. In the second physico-chemical system, calcium hydroxide was used as a coagulant material for chromium precipitation and plain sedimentation was applied for reducing of COD, biochemical oxygen demand (BOD(5)) and TSS. The results demonstrate 98.8% removal of chromium, 31% removal of COD, 25.8% removal of BOD(5) and 51.2% removal of TSS.

Research on orthogonal coagulated setting and coagulation-flotation test of tannery wastewater

The treatment of the tannery wastewater was studied by orthogonal test of beaker coagulation. FeSO4 and alkaline sodium aluminum waste liquid contained NaOH-NaAlO2 were used as flocculants, with polyacrylamide (PAM) as coagulation. When the dosage of FeSO4 was 2.66 g/L (pH 5.5), the wastewater pH value of adding alkaline sodium aluminum waste liquid was 8, and the dosage of PAM was 1 mg/L, the optimum result was obtained. A test device of co-coagulation flotation reactor was designed on the basis of the conglutination of bubble, flocci and turbulent flotation theory. In the device, the gas-1iuid mixed pump substituted the air compressor and the pressure releaser. The combination of coagulation and air flotation were realized. The pump is a new kind of air saturation equipment. The air compressor and the pressure releaser were used commonly in traditional air flotation device. The results of treatment of the tannery wastewater showed a stable state, when the operating pressure was 5×10(5) Pa, circumfluence ratio was 225%.

Generation of endocrine disruptor compounds during ozone treatment of tannery wastewater confirmed by biological effect analysis and substance specific analysis

Ozone (O3) with its high oxidation potential was used to degrade or eliminate pollutants contained in tannery wastewater when applying different pHs and quantities of O3. Our objective was a chemical degradation by O3 to achieve an enhancement of biodegradability, with a parallel decrease in toxicity. Conventional analyses and bioassays beside substance specific analyses were performed to clear-up the behaviour of wastewater content from tanning process. The results demonstrate that the dominant organic pollutants were chemically degraded by oxidation as the chemical and biochemical oxygen demand (COD and BOD) prove, while changes in carbon content monitored by total or dissolved organic carbon content (TOC or DOC) were only marginal. Vibrio fischeri and Daphnia magna toxicity testing performed in parallel proved a decrease in toxicity after O3-treatment, while the estrogenic activity determined by enzyme-linked receptor assay (ELRA), however, proved an increase of endocrine disruptor compounds (EDC). Results could be explained by substance-specific analyses using gas chromatography (GC-MS) and liquid chromatography/mass spectrometry (LC-MS). From GC-MS analysis the elimination of non-polar compounds could be recognized, whereas the oxidative conversion led to an increase of EDC compounds, which qualitatively could be identified by LC-MS as nonylphenol ethoxylate (NPEO) degradation products: short chain NPEOs, nonylphenol carboxylates (NPECs) and nonylphenol (NP).

Antimutagenic and antioxidant activities of quebracho phenolics (Schinopsis balansae) recovered from tannery wastewaters

Quebracho extracts are used in tannery due to their high concentration of phenolics. The Mexican tannery industry uses around 450 kg/m(3) of which, 150 kg/m(3) remains in wastewaters and are discharged in drain pipe systems or rivers. The quebracho phenolics recovered from tannery wastewater (QPTW) was characterized by HPLC. The antimutagenic and antioxidant activities as well as the microbiological quality were evaluated. Total phenolic content of QPTW was 621mg catechin equivalent/g sample. Gallic and protocatechuic acids were the major components characterized by HPLC. QPTW showed an inhibition range on aflatoxin B(1) mutagenicity from 16 to 60% and was dose-dependent. Antioxidant activity (defined as beta-carotene bleaching) of QPTW (64.4%) at a dose of 12.3mg/mL was similar to that of BHT (68.7%) at a dose of 0.33 mg/mL, but lower than Trolox (90.8% at a dose of 2.5mg/mL); meanwhile antiradical activity (measured as reduction of DPPH) (60.8%) was higher than that of BHT (50.8%) and Trolox (34.2%). Quebracho residues were demonstrated to be an outstanding source of phenolic acids and for research and industrial uses.

Leather waste--potential threat to human health, and a new technology of its treatment

In this paper, the authors deal with the problem of processing various types of waste generated by leather industry, with special emphasis to chrome-tanned waste. The agent that makes this waste potentially hazardous is hexavalent chromium. Its compounds can have negative effects on human health and some CrVI salts are considered carcinogens. The authors present the risks of spontaneous oxidization of CrIII to CrVI in the open-air dumps as well as the possible risks of wearing bad quality shoes, in which the chromium content is not controlled. There are several ways of handling primary leather waste, but no satisfactory technology has been developed for the secondary waste (manipulation waste, e.g. leather scraps and used leather products). In this contribution, a new three-step hybrid technology of processing manipulation waste is presented and tested under laboratory, pilot-scale and industrial conditions. The filtrate can be used as a good quality NPK fertilizer. The solid product, titanium-chromium sludge, can serve as an inorganic pigment in glass and ceramic industry. Further, the authors propose selective collection of used leather products (e.g. old shoes), the hydrolysable parts of which can be also processed by the new hybrid technology.

Physico-chemical analysis of tannery solid waste and structural characterization of its isolated humic acids after composting

In Marrakech, solid by-products from tanneries are highly polluting, generating large amounts of nitrogenous and organic matter. In the present study composting is tested as a cost-effective method for waste management to overcome many of the environmental hazards and produce a stable, rich material for soil fertilization. Two composting trials were conducted after neutralization by ammonia or lime. The aim of the neutralization was to avoid the antimicrobial effects of the acidity in the tannery waste, thus ensuring correct composting. Different techniques such as elemental analysis and 13C NMR spectroscopy were applied to analyse humic acids isolated from raw and composted materials, and to monitor the process of tannery waste composting, and the stability and maturity of the final product according to the means of neutralization. Comparison of data showed similar behaviour in both trials, but the composting process appeared to be more complete following neutralization with lime. The C, H and N content decreased, while the O increased. The FTIR and 13C NMR spectra show the decrease of aliphatic compounds demonstrated by the reduction of absorbance around 2922cm(-1) and of the resonance in the C-alkyl area around 0-55ppm. The humic acids newly formed during composting were richer in the O-N alkyl and oxidized aromatic structures that increased almost twofold on composting after neutralization with lime. The first principal component axis PC1 (54%) separated C-aliphatic, C-carboxylic and other less stable and less polycondensed compounds such as polyphenols from the more polycondensed O-N alkyl and oxidized C-aromatic compounds.

Process efficiency and microbial monitoring in MBR (membrane bioreactor) and CASP (conventional activated sludge process) treatment of tannery wastewater

In this study a pilot-scale membrane bioreactor (MBR) and a conventional activated sludge plant (CASP), treating the same tannery wastewaters and in the same operating conditions, have been compared in order to evaluate the overall treatment efficiency, the presence and distribution of Gram negative bacteria and the kinetics of nitrifying bacteria. Process efficiency was evaluated in terms of organic and nitrogen compounds: the MBR showed a higher COD removal (+4%) and a more stable and complete nitrification. The Gram negative bacteria were detected by fluorescent in situ hybridization (FISH) with phylogenetic probes monitoring of alpha-, beta- and gamma-Proteobacteria, of the main ammonia-oxidizing bacteria (AOB) and nitrite-oxidizing bacteria of the Nitrobacter and Nitrospira genera. The results showed that the main differences between the two sludges were: the higher abundance of alpha- and gamma-Proteobacteria in the MBR bioreactor and the presence of AOB aggregates only on the surfaces of MBR flocs. Finally, the titrimetric (pH-stat, DO-stat) tests showed similar values of the kinetic parameters of the nitrifiers both in MBR and CASP sludge.

Characterization of tannery wastewater and biomass in a membrane bioreactor using respirometric analysis

Respirometric techniques and an activated sludge model (ASM) were applied for the characterization of tannery wastewater and biomass in a pilot plant membrane bioreactor (MBR) operating at high sludge age. The traditional respirometric tests and the IWA-ASM1 were modified to take into account the specific operating conditions, the solid-liquid separation technology and the wastewater complexity. As a result the wastewater biodegradable COD was fractionated into four components: readily biodegradable, rapidly hydrolysable, slowly hydrolysable and inorganic (due to the presence of reduced sulphur compounds). The kinetic and stoichiometric parameters of the biomass (heterotrophic and nitrifying) were estimated through the integration of model simulations and respirometric tests results. In particular the ammonium and nitrite-oxidizing biomasses were separately characterized: the growth kinetics of ammonium and nitrite-oxidizing bacteria resulted noticeably lower than the traditional reference values (mu(max,AOB)=0.25d(-1)e mu(max,NOB)=0.23d(-1) at 20 degrees C, respectively). The ASM was finally used to confirm that the results of the wastewater and biomass characterization allow to properly simulate the mixed liquor suspended solids in the MBR pilot plant and the COD concentration in the effluent.

Hypertension in leather tanning workers working in Istanbul, Turkey

INTRODUCTION

Leather tanning may result in various occupational diseases. The aim of this study was to compare the relation between blood pressure levels and vocations in leather tanning.

METHODS

Our study was conducted in Turkey's leading leather process plant located in Tuzla organised industry zone, between March 11 and May 30, 2005. All leather plants that consented to participate in our study were included. The blood pressure, height and weight of the workers were measured. Their ages, educational levels, smoking habits and hypertension history were obtained via interviewing the subjects. The relation between three main factors, i.e. age, body mass index (BMI), working period, and hypertension were analysed through multiple logistic regression analysis.

RESULTS

40.4 percent (295) of 730 workers' blood pressure values were found to be within normal limits. 59.6 percent (435) were found to be hypertensive. The hypertension correlation remained significant, along with BMI and their working period (p-values were 0.0001 and 0.035, respectively).

CONCLUSION

Our study demonstrated that BMI and working period have a key influence on the increased risk of hypertension, which leads us to consider the importance of occupational exposure. Different hypertension studies to be conducted in various occupational fields would likely be able to confirm our findings.

Studies of chromium removal from tannery wastewaters by algae biosorbents, Spirogyra condensata and Rhizoclonium hieroglyphicum

Chromium in the effluent is a major concern for tanning industry. Chemical precipitation methods are commonly employed for the removal of chromium but this leads to formation of chrome-bearing solid waste, plus it is uneconomical when the concentration of chromium in the effluent is low. Ion exchange and membrane separation methods are relatively expensive. In this study, two algae namely, Spirogyra condensata and Rhizoclonium hieroglyphicum have been employed to remove chromium from tannery effluent. The effect of pH and chromium concentration showed S. condensata to exhibit maximum uptake of about 14 mg Cr(III)/g of algae at optimum pH of 5.0 whereas R. hieroglyphicum had 11.81 mg of Cr(III)/g of algae at pH of 4.0. Langmuir and Freundlich models were applied. Increase of initial concentration of Cr resulted to a decrease in adsorption efficiency. Dilute sulphuric acid (0.1M) showed good desorption efficiency (>75%). Interference from cations negatively impacted on biosorption of chromium. Immobilized algae on Amberlite XAD-8 in a glass column, gave better recovery of chromium in tannery effluent compared to a batch method with unimmobilized algae. Fourier transform infra red (FT-IR) analysis of the two algae revealed the presence of carboxyl groups as possible binding sites.

Quality assessment of treated tannery wastewater with special emphasis on pathogenic E. coli detection through serotyping

The present study was undertaken to assess the quality of treated tannery effluent discharged from Common Effluent Treatment Plant (CETP), Unnao, India, to various water bodies and agricultural lands. The physico-chemical analyses revealed that the effluent was yellowish-brown in colour, having alkaline pH, high BOD, COD values and contained large quantities of organic and inorganic constituents well above the prescribed standards. The bacteriological quality was assessed in terms of the presence of heterotrophs and total as well as faecal coliforms. All faecal coliforms were identified as Escherichia coli, of which 50% were found pathogenic after serotyping. Most of the serotypes were uropathogenic Escherichia coli (UPEC) 04. The potential risks of the contamination of different ecosystems situated to the vicinity of such sites are obvious. The observations of this investigation indicate that the treated tannery effluent released for various purposes is not satisfactory, and is far from optimal in attaining the safe limits of disposal.

Evaluation of different substrates to support the growth of Typha latifolia in constructed wetlands treating tannery wastewater over long-term operation

The aim of this study was to investigate the performance of horizontal subsurface flow constructed wetlands planted with Typha latifolia treating tannery wastewater under long-term operation. Two expanded clay aggregates (Filtralite MR3-8-FMR and Filtralite NR3-8-FNR) and a fine gravel-FG were used as substrate for the constructed wetland units plus one unit with FMR was left as an unvegetated control. The systems were subject to three hydraulic loadings, 18, 8 and 6cmd(-1), and to periods of interruption in the feed. The relationship between the substrate, plant development and removal efficiency, especially of organic matter, was investigated. Organic loadings up to 1800kg BOD(5)ha(-1)d(-1) and 3849kg COD ha(-1)d(-1) were applied leading to mass removals of up to 652kg BOD(5)ha(-1)d(-1) and 1869kg COD ha(-1)d(-1), respectively. The three different substrates were adequate for the establishment of T. latifolia, although the clay aggregates allowed for higher plant propagation levels. The units with FNR and FMR achieved significantly higher COD and BOD5 removal when compared to the FG and to the unplanted units. The systems proved to be tolerant to high organic loadings and to interruptions in feed suggesting this technology as a viable option for the biological treatment of tannery wastewater.

Comparative growth response of two varieties of Vigna radiata L. (var. PDM 54 and var. NM 1) grown on different tannery sludge applications: effects of treated wastewater and ground water used for irrigation

This study evaluates the possibility of using contaminated soil by treated tannery wastewater and the use of tannery sludge in agriculture. The plants of Vigna radiata var. PDM 54 grown on contaminated soil and irrigated with ground water have not shown the translocation of toxic metal (Cr) in the upper part. The biomass of the plant increased when irrigated with treated tannery wastewater compared to ground water, whereas no significant change was observed in chlorophyll and protein contents. In both the varieties (var. PDM 54 and var. NM 1) of V. radiata grown on tannery sludge amendments, the growth parameters exhibited a pronounced positive growth response up to 35% tannery sludge amendments compared with the plants grown on garden soil. Despite the Cr accumulation at lower amendments, no toxicity symptoms were observed in both the varieties of the plants. Higher amendments affected various growth parameters, NR activity, and carbohydrate content of the plants. The results suggest that the plants of V. radiata (var. PDM 54) may be grown on contaminated soil or lower sludge amendments and irrigated with ground water. No translocation of toxic metal Cr was found in the seeds of the plants grown in up to 25% tannery sludge. However, periodical monitoring is required before the consumption of seeds. Overall, the results showed that plant growth patterns were influenced to some extent by the level of soil contamination and the water used for irrigation.

The effects of tannery wastewater on the development of different plant species and chromium accumulation in Phragmites australis

Toxicity tests were performed to assess the effect of tannery wastewater with different treatment levels on two wetland plants, Phragmites australis and Typha latifolia, which are frequently used in constructed wetlands (CWs) for water treatment, and thus deepen the knowledge on their capacity to withstand the application of industrial wastewater. Trifolium pratense, a plant generally used as an indicator in toxicity tests, was included as a control. End points measured were germination percentage, shoot length, root elongation, and biomass growth of the plants. When tannery effluent, with a low treatment level, was supplied to the wetland plants germination occurred even at effluent concentrations of 100%, whereas germination of T. pratense was completely inhibited, almost invariably, at effluent concentration of 50%. Higher germination levels were achieved when the plants were exposed to effluent originating from the outlet of constructed wetland pilot units, allowing germination of all tested plants, indicating a significant decrease in its toxicity level. Experiments conducted with the same plants using different growing substrata as the germination matrix, namely expanded clay aggregates (Filtralite MR 3-8 and Filtralite NR 3-8) and two types of sand (fine gravel and standard sand) have shown that higher germination levels were achieved in standard sand and that P. australis was the plant species showing higher germination in all cases, reinforcing the robustness of this plant to environmental stress. The phytoextraction potential of P. australis, was evaluated by subjecting the plant to tannery wastewater supplemented with 50 and 150 mg Cr/L. After 6 weeks of exposure, levels up to 4825, 883, and 627 mg Cr/kg were found in the rhizome, shoot, and leaves, respectively, although phytotoxic signs in the plant were evident. This plant might not be considered a chromium hyperacumulator, but the potential to extract and accumulate this metal on its rhizomes is high.

Identification and characterization of sulfur-oxidizing bacteria in an artificial wetland that treats wastewater from a tannery

Wastewater from tanneries contains high concentrations of organic matter, chromium, nitrogen, and sulfur compounds. In this study, an artificial wetland is is used as the tertiary treatment in a tannery in León Gto., México. It consists of three subplots with an area of about 450 m2. Two subplots were planted with Typha sp. and the third with Scirpus americanus. Geochemical analyses along the flowpath of the wetland show that contaminants were effectively attenuated. The most probable number technique was used to determine rhizospheric microbial populations involved in the sulfur cycle and suggested that there were 104-10(6) cells g(-1) sediment of sulfate-reducing bacteria and 10(2)-10(5) of sulfur-oxidizing bacteria (SOB). Representatives of SOB were isolated on media containing thiosulfate. Phylogenetic analysis of 16S rRNA of SOB isolates shows that they belong to the genera Acinetobacter, Alcaligenes, Ochrobactrum, and Pseudomonas. Most of the isolates are organotrophic and can oxidize reduced sulfur compounds such as elemental sulfur or thiosulfate, accumulating thiosulfate, or tetrathionate during growth. All isolates can use reduced-sulfur compounds as their sole sulfur source and some can use nitrate as an electron acceptor to grow anaerobically. Our results illustrate the relevance of SOB in the functioning of the wetland constructed for tannery wastewater remediation.

Use of modified hydroxy-aluminum bentonites for chromium(III) removal from solutions

The retention of chromium(III) from a 2,000 ppm chromium basic sulfate and tannery waste solution at pH 4.5 using modified hydroxy-aluminum bentonites (OH-Al bentonites) as adsorbents was studied. OH-Al bentonite was prepared by mixing clay with a hydrolyzed commercial chlorohydroxy Al solution. The modified Al bentonites were obtained by (a) a treatment with 0.5M sodium chloride and (b) a treatment with a Na-hexametaphosphate solution (HMP) after adding sodium chloride. The effect of heating the adsorbents at 100, 500, 700 and 800 degrees C on Cr retention as a function of time was also analyzed. Cr retention by modified OH-Al bentonite with HMP increased with time (up to 100 mg Cr/g) where modified OH-Al bentonite was twice that of untreated bentonite. The relatively high uptake of metal from the salt solution by modified OH-Al bentonite treated at 800 degrees C, in which a complete interlayer collapse occurred, indicated the importance of the contribution of external surface sites to the retention capacity. The maximum Cr uptake from a water waste was 24 mg/g, due to interferences and different chromium species in the industrial solution.

The effect of mixing pharmaceutical and tannery wastewaters on the biodegradation characteristics of the effluents

This paper evaluated the effect of mixing the effluent of a pharmaceutical plant producing acetylsalicylic acid with tannery wastewater, on the biodegradation of the effluents. The evaluation involved the analysis of the oxygen uptake rate (OUR), profiles of each wastewater and the mixture by respirometry. Model calibration using the experimental OUR data identified major COD fractions and associated process kinetics for all samples analyzed. The tannery sample was a plain-settled effluent having a total COD of around 2200 mg/L with a readily biodegradable fraction of 15%. The same fraction was 57% in the pharmaceutical wastewater sample having a much stronger total COD content of 40,435 mg/L. Consequently, mixing of the pharmaceutical effluent with the tannery wastewater up to 38% of the total COD in the mixture increased the readily biodegradable COD fraction but had an inhibitory effect on the biodegradation kinetics. This effect was relatively lower on growth, but quite significant on the hydrolysis of the slowly biodegradable COD decreasing the maximum hydrolysis rate from 2.0 day(-1) to 1.2 day(-1). Model evaluation of the respirometric data, as performed in this study sets a workable protocol for the assessment of the compatibility of different wastewater mixtures for biological treatability.

Leaching behavior of chromium in chrome shaving generated in tanning process and its stabilization

In this study, leaching properties and pollution potential of chromium in chrome shaving (CS), which is a solid residue of leather industry, containing 2.27% Cr were investigated and thermal stabilization procedure was applied to the CS for chromium immobilization. For this purpose, firstly, effects of the liquid/solid ratio, contact time, pH and sequential extraction on the leaching behavior of chromium in the CS were studied. It was determined that the CS-caused chromium pollution is a hazardous material for environment. Thermal stabilization procedure was applied to the CS in the temperature range of 250-500 degrees C for the chromium immobilization. Effective stabilization of chromium in the CS was achieved by heating of CS at 350 degrees C under CO(2) atmosphere. Leaching experiments were also carried out with the samples obtained from the stabilization process and the results compared with that of the CS. Also, TCLP test method was applied to the samples to determine pollution potentials and discharge situations of the CS and its stabilization products. While the chromium concentrations in the test solutions of all samples stabilized thermally at above 350 degrees C were below the USEPA regulatory limit of 5 mg/l, the concentration of chromium leached out from the CS was 30-fold bigger than the USEPA regulatory limit.

Volatility of heavy metals during incineration of tannery sludge in the presence of chlorides and phosphoric acid

Knowledge of the behaviour of heavy metals in the combustion process is a most important factor in selecting disposal alternatives for waste materials. Accordingly, in this work, the vaporization behaviour of highly concentrated heavy metals (Pb, Zn, Cu and Cr) in tannery sludge were investigated experimentally. The sludge was spiked with various chlorine compounds (i.e. PVC, FeCl3, CaCl2 and NaCl) and pre-treated with phosphoric acid in order to evaluate the capacity of enhancement and weakening of the volatility of the heavy metals contained in tannery sludge. The experimental results show that the vaporization percentages increased with increasing ratio of Cl/sludge and temperature, and the accelerating and increasing effect of the addition of chlorides on the vaporization percentage of heavy metals was dependent on the release capacity of chlorine radicals. The vaporization percentages of lead and zinc increased by 15-20%, whereas those of copper and chromium increased by only about 3 and 10% at 800 degrees C. However, heavy metals were not expected to be completely released in the combustion process in spite of the high ratio of Cl/sludge. Alternately, heavy metals contained in tannery sludge can be immobilized effectively by pre-treatment with phosphoric acid. When the 85% phosphoric acid accounted for 10% of dry basis of tannery sludge, the phosphate-treated sludge showed the lowest vaporization percentage of about 3-15% with formation of Ca18Cu3(PO4)14, Ca9Cr(PO4)7, Ca19Zn2(PO4)14 and PbMgP2O7 in the bottom ash.

Haematological and biochemical effects of polyphenolics in animal models

Polyphenols of natural and synthetic origin are exploited in tanning sector to convert putrescible skin/hide to non-putrescible leather. However, only 30-40% of the inputs have been taken up for processing, the remaining is released as unspent. The existing conventional wastewater treatment systems are inefficient in removing or degrading these unspent polyphenols and thus detrimental to ecosystem. The present study demonstrates the evaluation of impact of both synthetic and natural polyphenols on biochemical and haematological properties of blood and serum in animal models. The results reveal that concentrations of polyphenols play a major role. At higher concentrations, irrespective of their nature, there was a marked change in the lipid profile (81% reduction), followed by insignificant change in glucose levels, RBC and WBC counts and other haematological parameters. At lower concentrations, no significant changes in the above said properties were observed.

Environmental conditions affecting exopolysaccharide production by Pseudomonas aeruginosa, Micrococcus sp., and Ochrobactrum sp

Three different chromium-resistant microorganisms (Pseudomonas aeruginosa, Micrococcus sp., and Ochrobactrum sp.) were tested with regard to their EPS production at different pH levels, temperatures, Cr(VI) concentrations, and incubation periods. The optimum pH level was 7 for P. aeruginosa and Micrococcus sp., while it was 8 for Ochrobactrum sp. according to the highest EPS amount at 100 mg/L Cr(VI) concentration. The highest production of EPSs by the three bacteria was obtained under different environmental conditions. P. aeruginosa produced the highest EPS (863.3 mg/L) after incubation for 96 h on media with 50 mg/L Cr(VI) at 20 degrees C, Micrococcus sp. gave the highest yield (444.6 mg/L) after incubation for 72 h on media with 100 mg/L Cr(VI) at the same temperature, and Ochrobactrum sp. had the highest production (430.5 mg/L) on media with 150 mg/L Cr(VI) at 30 degrees C at the end of 48 h of incubation.